Search Results

Search found 57250 results on 2290 pages for 'windows 2008r2'.

Page 363/2290 | < Previous Page | 359 360 361 362 363 364 365 366 367 368 369 370  | Next Page >

• Silent install FirePro v4900 Driver on Windows Embedded 7 Standard

  - by Birgit_B

  I'm trying to install the Drivers for a FirePro v4900 on a Windows Embedded 7 Standard 64bit OS. I want the system to be as small as possible, so i would rather not install the whole catalyst control center, but only the necessary drivers. Because the installation should be accomplished absolutely unattended, the installation process of the FirePro-Driver should also be done without any user interaction. I see two possible solutions for the Problem: Install only the Drivers: Is it possible to solely install the necessary drivers? How would i achieve that? This solution would be the preferred one, because of the smaller footprint. Silent custom install the provided "FirePro_8.911.3.3_VistaWin7_X32X64_135673.exe" (found at ATI FirePro™ Driver). Is there a way, to do that? Thank you in advance for your support! Update: I managed to accomplish a silent installation. I extracted the contents of the above mention installer-file and ran \$_OUTDIR\Bin64\Setup.exe -Install. (There are some other Parameters, just run Setup.exe /?). But i couldn't achieve to just install the drivers without the Cataclyst Control Center, and it seams the Control Center has some unfulfilled dependencies and so it crashes...

  Read the article

• windows clients cannot get dns resolution until you open and close ipv4 properties page

  - by GC78

  This strange problem has started recently. Some windows clients cannot seem to get dns resolution to the internet after boot, and sometimes again at some point in the day. Internal hosts are also slow to resolve. trying to ping an interal host by name will take a long time for the hostname to resolve to ip address and trying to ping a website by name will fail to resolve. If you go into the tcp/ip v4 properties and view but not change anything, ok/close out of that then the client starts working fine, hostnames will resolve quickly. I have seen this happen on both Vista and W7 clients. ipconfig /all at a client experiencing this problem shows everything in order. proper ip addr, gateway, dns server, dns suffix ect.. ipconfig /dnsflush will not fix them, neither will /release and /renew the clients get their ip address, mask and dns server info from either one of 2 OES dhcp servers that assign addresses in different scopes in the same subnet. the internal dns server is a different OES dns server the default gateway is not assigned by the OES server but is statically put in at the client (only for those who need to get to the Internet for their job) flat network topology What can I do to get to the bottom of this? It only happens to a few of the client machines and typically the same ones. It started happening when we made a change to one of the DHCP scopes in iManager. Strangly this problem only happens to clients that get an IP address from the scope that we didn't make any changes to.

  Read the article

• Software Diagnostics Tool recommendations for Debugging a Windows 8 freeze

  - by Stuart

  I've had my HP Pavillion dv6 laptop since last November - and it has had 8GB RAM and a 256GB Crucial M4 SSD installed since the start. I use it for software development and it's had a Windows 8 RTM installation since early September. Yesterday I had to give a presentation at a customer site - so used Powerpoint for the first time since installing Win8... since that point my machine has 'frozen' every 2 hours or so after startup. There doesn't seem to be any easy to see reason behind the freeze - the system just freezes, even if I have left it idle with just a desktop there. My immediate suspicion is that the SSD is the mostly likely cause of the problem. I've looked at some of the questions on here - e.g. How do I troubleshoot hardware issues related to a computer freeze/crash? - but don't really want to start taking my laptop apart. Another suspicion is that this might be related to the WiFi adapter (Broadcom 802.11n) since I have noticed that this doesn't seem to play perfectly with things like Hyper-V in Win8. Can anyone recommend any software diagnostic tools that I can run in order to evaluate the health of the SSD or of other parts of the system? Thanks Stuart P.S. I doubt Powerpoint is the cause of this, but I may use it as an excuse never to use it again... More realistically perhaps something got damaged during travel to the customer site?

  Read the article

• Windows Vista - Can Boot into Safe Mode Command Prompt, Cannot Access Flash Drive

  - by Adam

  Hey there, Got a laptop dropped into my lap. Has Vista installed. Normal boot never gets past the login screen. Safe mode will get past, but just barely. I can try and start the task manager at that point, but it never opens. Only reliable way to do anything I've got is the safe mode command prompt... Boots up and logs in fine. I can't see anything noticably wrong via regedit, but it's been a long time since I've had to fix up a Windows box... not sure that I would. Problem I'm having, is that I want to run ComboFix/etc, but have no way to get them on there... When I pop a flash drive in, it seems to mount it (flash drive flickers as normal) but it never seems to be mounted... I cannot access it through any drive letter on the command line. I managed to start the device manager (devmgmt.msc) and the flash drive was recognized and listed... Any ideas on how to get this thing going again? (Short of a reinstall.) (It has no CD drive, either, so burning files to CD would not be easy...) Thanks! Adam

  Read the article

• how to reinstall ubuntu 12.04 after dual boot installation fails with windows 7

  - by Rini

  I have installed Ubuntu 12.04 on my preinstalled windows 7 Sony vaio s series laptop following instructions here: http://www.linuxbsdos.com/2012/05/17/how-to-dual-boot-ubuntu-12-04-and-windows-7/ Everything went well and I am able to boot in to windows after complete installation of Ubuntu. Now following instructions on web I tried to add Ubuntu to my BIOS using Easy BCD (but forget to add windows 7 entry). As a result, I loose windows 7 OS and can't boot in to either OS then I successfully repaired windows 7 using recovery CD. Now my problem is that I can't reinstall Ubuntu 12.04 using Live CD it halts every time before disk partition step giving error. There is only one partition which corresponds to windows 7 but I don't know whether the Ubuntu is still there or probably corrupted. So, how to repair it or again install ubuntu ? Please suggest what I should do now? Thanks in advance. R Shukla

  Read the article

• network policy + WPA enterprise (tkip) Windows 2008 R2

  - by Aceth

  hi I've attempted the following guide and in a bit of a pickle. http://techblog.mirabito.net.au/?p=87 My main goal is to have a username / password based wireless authentication with active directory integration. I keep getting the error Network Policy Server denied access to a user. Contact the Network Policy Server administrator for more information. User: Security ID: domain\rhysbeta Account Name: rhysbeta Account Domain: domain Fully Qualified Account Name: domain\rhysbeta Client Machine: Security ID: NULL SID Account Name: - Fully Qualified Account Name: - OS-Version: - Called Station Identifier: 00-12-BF-00-71-3C:wirelessname Calling Station Identifier: 00-23-76-5D-1E-31 NAS: NAS IPv4 Address: 0.0.0.0 NAS IPv6 Address: - NAS Identifier: - NAS Port-Type: Wireless - IEEE 802.11 NAS Port: 2 RADIUS Client: Client Friendly Name: Belkin54g Client IP Address: x.x.x.10 Authentication Details: Connection Request Policy Name: Secure Wireless Connections Network Policy Name: Secure Wireless Connections Authentication Provider: Windows Authentication Server: srvr.example.com Authentication Type: EAP EAP Type: - Account Session Identifier: - Logging Results: Accounting information was written to the local log file. Reason Code: 22 Reason: The client could not be authenticated because the Extensible Authentication Protocol (EAP) Type cannot be processed by the server. ` I would love to have it so that non domain devices

  Read the article

• Windows PE network setup

  - by microchasm

  I'm walking through the following step-by-step guide for deploying Windows 7 via AIK: http://technet.microsoft.com/en-us/library/dd349348%28WS.10%29.aspx On step 4 (Capturing the Installation onto a Network Share), I run into a bit of a snag: attempting to connect to a network drive repeatedly fails. I'm using/deploying Dell Optiplex 380 64 bit machines, and the network cards seem to be really wonky. On the machine that I'm using to run AIK etc, the network driver wasn't found automatically. I had to manually go in and install the driver (which was found on the OEM installation media). I've since copied this to the USB key that I'm using for the Autounattend.xml so its handy. I think that because of this, the PE environment doesn't or can't instantiate the network device. Is there a way to install/configure the network device through the command prompt in PE? If not, I read about adding in the answer file path(s) to drivers, but if I did it this way, would I have to start the process all over again (i.e. create new Autounattend.xml with the PnPcustomizations path included, re-run the installation on the reference machine, install all the applications, re-make the PE iso, reboot into new PE iso)? Any shortcuts, direction, or advice would be appreciated. Thanks!

  Read the article

• Windows 2008 64bit: applications and explorer always hang

  - by Phil Farthing

  I setup a couple of Window 2008 64bit systems about 5 months ago. Initially all seemed well. Now however, for no apparent reason, things are dog slow, apps hang, explorer hangs, just clicking on something can cause a CPU spike of 100%, and often it's explorer that is eating it up. As I have two on identical hardware, and they experience the same problem, it doesn't seem related to addon software. The only thing these have in common is Kaspersky and I've tried disabling/uninstalling to no avail. There are no useful error messages in the event logs. Actually, the system never even reports app hangs. Sometimes, it similar to what I've seen on Windows 7 systems where the screen goes milky and asks if I want to trouble shoot, that's only when get impatient and click happy. The really odd thing, is that it will NOT do this for a few minutes at a time, and then starts up again. Like I will click on the start menu and browse for the Admin Tools, the start menu will hang at some point and I'll have to wait about a minute, then it's OK. The next time I do this, a few seconds later, it's fine. Every click seems to hang the first time around, then be ok the second time if I do the exact same thing. If anyone has any suggestions, please PLEASE let me know! thanks =)

  Read the article

• Windows Server 2008 (Web Server) Replication

  - by justjoshingyou

  We have a load balanced environment with Windows Server 2008. What are some best practices to setting up replication across the web servers? Do I only want to replicate the web folders? How about replicating IIS changes - or do I need to make IIS changes on every server? I've never, ever set up replication, but I have worked with a web farm that used it before. Basically, I only know the basics about how it works, and am looking for any advice, guides, warnings, etc on setting this up. If you'd like to offer any advice, I'll let you know how our environment is for now. We have 1 prod server up and the second is nearly ready to go. We are using a cloud system and all machines are VM's. I am in the process of setting up the domain controller now (as I need to have one for DFS). Any ideas on the best way to go about setting up replication? Should we just stick the prod server in from the start or set up using a test VM and our second server and then switch it up later? I do not want to risk overwriting our prod server. Thanks!

  Read the article

• windows xp blue screen dumping physical memory

  - by dotnet-practitioner

  I get following blue screen after running my laptop for an hour... A problem has been detected and windows has been shut down to prevent damange to your computer. If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to be sure you have adequate disk space. If a driver is identified in the stop message, disable the driver or check with the manufacturer for driver updates. Try changing video adapters. Check with your hardware vendor for any BIOS updates. Disable BIOS memory options such as cashing or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select advanced startup options, and the select safe mode. Technical Information: * STOP 0x0000008E (0xc0000005, 0x805B03F5, 0xF703DC7C, 0x00000000) Beginning dump of physical memory Physical memory dump complete. Contact you system administrator or technical support group for further assistance. so.... if this is a faulty memory.... from where I could buy RAM for following laptop.... TOSHIBA SATELLITE A45-S250 My local Frys store does not carry memory for this laptop.

  Read the article

• Compressing and copying large files on Windows Server?

  - by Aaron

  I've been having a hard time copying large database backups from the database server to a test box at another site. I'm open to any ideas that would help me get this database moved without having to resort to a USB hard drive and the mail. The database server is running Windows Server 2003 R2 Enterprise, 16 GB of RAM and two quad-core 3.0 GHz Xeon X5450s. Files are SQL Server 2005 backup files between 100 GB and 250 GB. The pipe is not the fastest and SQL Server backup files typically compress down to 10-40% of the original, so it made sense to me to compress the files first. I've tried a number of methods, including: gzip 1.2.4 (UnxUtils) and 1.3.12 (GnuWin) bzip2 1.0.1 (UnxUtils) and 1.0.5 (Cygwin) WinRAR 3.90 7-Zip 4.65 (7za.exe) I've attempted to use WinRAR and 7-Zip options for splitting into multiple segments. 7za.exe has worked well for me for database backups on another server, which has ~50 GB backups. I've also tried splitting the .BAK file first with various utilities and compressing the resulting segments. No joy with that approach either- no matter the tool I've tried, it ends up butting against the size of the file. Especially frustrating is that I've transferred files of similar size on Unix boxes without problems using rsync+ssh. Installing an SSH server is not an option for the situation I'm in, unfortunately. For example, this is how 7-Zip dies: H:\dbatmp>7za.exe a -t7z -v250m -mx3 h:\dbatmp\zip\db-20100419_1228.7z h:\dbatmp\db-20100419_1228.bak 7-Zip (A) 4.65 Copyright (c) 1999-2009 Igor Pavlov 2009-02-03 Scanning Creating archive h:\dbatmp\zip\db-20100419_1228.7z Compressing db-20100419_1228.bak System error: Unspecified error

  Read the article

• Black Screen on Logon (windows 7 home premium)

  - by Blacknight334

  i have been having some trouble with a dell Xps 15 laptop that i recently purchased. it is under a month old, and a problem has occurred, upon logging on just after start up, the computer will just sit on a black log on screen (with the mouse still visible and active) for a few minutes. it is extremely annoying, especially when im in a rush. the laptop is under a month old. So far, i have tried to update the drivers, all windows update, and still, nothing. also, it doesnt seem to do it when i log into safe mode, or if it does, it will do it for less than 10 seconds, then load the desktop (in normal boot, it usually takes a few minutes). i have also run a number of the inbuilt diagnostics, but found no errors. i want to avoid having to do a system restore for as long as i can. does anyone know anything that can help? (the laptop is running a 500gb SSD, 2gb Nvidia 640m, 8gb ram, 3rd gen i7 quad core with 8 threads) thanks.

  Read the article

• Windows 7 boot issues

  - by Michael

  Ok, I tried to install linux and dual boot my laptop with 7 ultimate. I messed up. When I tried to boot to 7 it said no. Something along the lines of device not found. So I being young and stupid I uninstalled linux which I could boot into, and I still could not boot to windows. Next step was to run the startup fixes from the boot cd. Swing and a miss, I also ran the fixmbr and fixboot. Which brings us up to my current place. I installed 7 again on my blank partition in hopes I could access my other partion. No dice. So my question to yall is how can I fix my original filesystem or at least get to the stuff on it. In the new 7 install the old partion does not even have a drive letter. That is my sad story any help would be apreciated.

  Read the article

• Feasibility of Windows Server 2008 DFS replication over WAN link

  - by CesarGon

  We have just set up a WAN link that connects two buildings in our organisation. The link is provided by a 100-Mbps point to point line. We have a Windows Server 2008 R2 domain controller on each side of the link. Now we are planning to set up DFS for file services across the organisation. The estimated data volume is over 2 TB, and will grow at approximately 20% annually. My idea is to set up a file server in each building and install DFS so that all the contents stay replicated over the 100-Mbps link. I hope that this will ensure that any user will be directed to the closest (and fastest) server when requesting a file from the DFS folders. My concern is whether a 100-Mbps WAN link is good enough to guarantee DFS replication. I've no experience with DFS, so any solid advice is welcome. The line is reliable (i.e. it doesn't crash often) and our data transfer tests show that a 5 MB/sec transfer rate is easily achieved. This is approximately 40% of the nominal bandwidth. I am also concerned about the latency. I mean, how long will users need to wait to see one change on one side of the link after the change has been made on the other side. My questions are: Is this link between networks a reliable infrastructure on which to set up DFS replication? What latency times would be typical (seconds, minutes, hours, days)? Would you recommend that we go for DFS in this scenario, or is there a better alternative? Many thanks.

  Read the article

• The MySQL service is in the status "starting" on windows

  - by andres descalzo

  I have several months working to "MySQL-5-1-47" on windows 2003. When I restarted, the service "MySQL" stay in this state "starting". The only way to raise the service was running the program directly: C:\Program Files\MySQL\MySQL Server 5.1\bin\mysqld This is the MySQL error log 100906 16:07:29 [Note] Event Scheduler: Purging the queue. 0 events 100906 16:07:32 InnoDB: Starting shutdown... 100906 16:07:37 [Note] Plugin 'FEDERATED' is disabled. 100906 16:07:38 InnoDB: Shutdown completed; log sequence number 0 44233 100906 16:07:38 [Note] mysqld: Shutdown complete 100906 16:07:39 InnoDB: Started; log sequence number 0 44233 100906 16:17:21 [Note] Plugin 'FEDERATED' is disabled. 100906 16:17:22 InnoDB: Started; log sequence number 0 44233 100906 16:22:01 [Note] Plugin 'FEDERATED' is disabled. 100906 16:22:02 InnoDB: Started; log sequence number 0 44233 100906 16:22:02 [Note] Event Scheduler: Loaded 0 events 100906 16:22:02 [Note] C:\Program Files\MySQL\MySQL Server 5.1\bin\mysqld.exe: ready for connections. Version: '5.1.47-community' socket: '' port: 3306 MySQL Community Server (GPL) The last lines are after loading the program from the shell Thank.

  Read the article

• Windows XP Setup Fails to Recognize USB Floppy after formatting AHCI disk

  - by Strahn

  I am attempting to install Windows XP Professional x64 onto a HP EliteBook 8540w. I have downloaded both the latest Intel Rapid Storage Technology drivers and the Intel Storage Matrix drivers that are listed on HPs website and copied the drivers over to a floppy disk (two separate floppies, one for each version of the drivers.) Booting to my WinXP Pro x64 install CD, I go through the F6 process, load the driver and am able to see my HDD, delete, create and format partitions on it. When I go to continue the install, after checking the disk, the system asks me to enter the disk labeled "Intel Rapid Storage Technology" and press enter to continue. Nothing happens at this point when I press enter. This happens if I use the latest drivers or the older drivers. We have created a slipstreamed install CD using nLite that has the AHCI drivers integrated, which installs fine. However, we have identified a number of issues with the system that I believe are side-effects of using nLite for the slipstreaming and I am attempting to verify that. I have researched this issue and found a few examples of others having the same problem, but no solution. The USB floppy is a Lacie branded floppy, connecting it to a working XP workstation shows it to be the Y-E Data USB floppy drive that is supposedly 100% compatible with XP per MS KB 916196.

  Read the article

• Windows 7 64bit will not register a 32bit DLL

  - by Bad Neighbor

  I'm trying to install a 32bit Oracle instant client onto several Windows 7 PCs. This version is the one required by the customer's software. I have successfully installed it on about a dozen PCs using the same installer, but two machines refuse to register a DLL. The two PCs are of different make and model. I have been able to install this software in the past on these models. This is the error that the installer throws up: The file copies to the location referenced above. If I choose to ignore the error and manually register it later, I get the following error: This error is returned whether I use the 32bit (syswow64) or 64bit version of regsvr32. Command Prompt is run as admin, and the ID with which I'm logged into the PC is an admin. I've tried copying the file into the syswow64 folder, but I get the same error. This same installer works on other PCs. To further complicate the issue, one of the two PCs also will not register an OCX file from a different 32bit installer: Both PCs are relatively new and have standard software installed. We use MS Forefront for security, but disabling that didn't change the behavior. What am I missing?

  Read the article

• Limit copssh users to home directory Windows 7

  - by Siriss

  Hello all- I have found these two sites below: CopSSH SFTP -- limit users access to their home directory only and http://blogs.windowsnetworking.com/wnadmin/2006/11/07/copssh-restricting-users-access/ as well as the Copssh website, but upon completion they do not seem to work. I have copssh installed and I have a separate Windows account "sftpuser" created that is used to connect. The connection works just fine, but I want to limit that user to just their home directory and sub folders. I have 3 hard drives, the C:, a W: and an S: and I want the FTP account to only be able to access the W: drive and its contents (the root of the W: drive is the FTP home directory). Right now "sftpuser" can access all folders, including jump drives to C:, and S:. The linked tutorials do not seem to work, because it seems when I create a group "ftpusersgroup" and add "sftpuser" to the group, and then deny "ftpusersgroup" access to the C: drive, the service breaks and I can no longer login. I have undone everything and am ready to start fresh. Does anyone know how to do this, or is there a better tutorial that someone has or has found? I hope this makes sense. Thank you very much for any help!

  Read the article

• Restoring Windows 2008 Server X86 and X64

  - by rihatum

  Restoring Windows 2008 Server (Domain Controller) We are using Backup Exec System Recovery 2010 to Image our DC. Now this software has a feature to convert the backup into a vmware or hyper-v VM I have also used disk2vhd to convert one of our dc's to a vhd and when I connected it into Hyper-V, it booted fine, I can login - BUT :-) As soon as I login, I get the activation error, that change product key, this product key isn't good for this machine etc. Question is : When in a real recovery situation, what would be the procedure to restore it either virtual or onto a physical box but be able to login and change product key etc ? In this scenario its just locked down and I cant' do anything, if this is the case, how would I replicate my production environment via these tools ? Any Ideas ? Will be grateful for some real world examples here. Same thing happens with our exchange backup / test restore either physical or virtual, can login but nothing else. Now we don't have the keys as they are OEM keys and just wondering what will happen in a real scenario, would we be purchasing another KEY or using the OEM key on our new server ? This is a test environment I am trying to create by restoring our backups either into hyper-v or physical test machines. Also, If I build up a machine (Server 2008) in a VM (Hyper-V), How can I restore just the system state backup of my DC into it ? will that give me the activation error too ? even though I would use the TRIAL ISOs provided by Microsoft ? Kind regards

  Read the article

• Fixed Resource Monitor Graph Scale in Windows Server 2008 R2

  - by Clever Human

  In Windows Server 2008 R2's Resource Monitor, is there a way to set the scale of the various graphs to be constant values instead of variable based on data? It seems to me that the utility of a graph is to get a quick overview glance at the values those graphs are showing. So if I look at the CPU graph and the line is up near the top, I can know immediately that something is using all my CPU and go investigate what. I don't really care if the CPU is jumping between .01% and 2%. Or if the network usage monitor is up near the top, I will know that all my bandwidth is being used up, and go figure out what. But the way things are now, the graphs are meaningless because the scales constantly shift. If you look at the network usage graph in one second it might have a scale out of 100kbps, and the next second have a scale based on 1mbps! So... is there a registry key or something that will peg the scale of these graphs to logical maximums?

  Read the article

• Maintaining "Portability" Between Linux and Windows 7

  - by lokheart

  I am using the following ways in my office's Windows 7 machine to maintain my "portabilibity" when disaster strikes and I need to switch computer while I have no luxury of time for reinstalling all my program to the new PC. a majority of programs I used are portable, mostly from portableapp.com, like notepad+, GIMP, even R, I extract them and store them in a folder in My document, in a structure similar to the default portableapp installation when they are installed to a thumbdrive only a few software that portable version is not available and I will install them as usual all of my working files are stored in a folder in My document I regularly backup them all using syncback, because this program can keep versioning of my backup, and the backup is stored in a portable drive. One day I need to switch my computer and the operation is relative simple for me: I just move the two folders mentioned above into the my document folder of the new PC, install those few "non-portable" program in it, and this is almost done, some minor hiccups can be solved by reinstalling the portableapp into the drive. Overall speaking it is a smooth process. I would like to maintain the same degree of "portability" in my home Linux desktop (Ubuntu or Mint, I'm still deciding), that is, if my Linux crash and I need to reinstall it again. All I need to do is the move the two folder back to the new Linux, and most of my work will be almost ready to be worked on again. But I don't know how to find a Linux-alternative of portableapps. Being a newer to Linux, can anyone tell me whether this is possible in Linux?

  Read the article

• FTP issues with Windows 2003 box and Filezilla

  - by vanhornRF

  We've set up a Windows 2003 server with IIS 6 and the FTP is Filezilla. I'm not a sys admin by any means and neither is my other developer. I'm trying to connect to FTP on a Mac with a Cyberduck FTP client. I'm running OSX 10.6.3. The problem is that I can connect to the FTP address, but when I do it will hang for a minute or two trying to list the directories. This address is pointed to the webroot folder so it's only trying to list the pertinent folders for the site we're working on. Eventually after a minute or two it will go through and list everything and then if you try and open a file or another folder, it will hang again and then eventually list the folders. My question: Is there some stupid default setting we're missing? Is this a common occurrence? Like I said I'm not a sys admin at all and I'm sure I'm missing some valuable questions for anyone that reads this, so please fire away if you can help and you need more info, I'll do my best to provide it. Thanks!

  Read the article

• Hiding subfolders from users with Windows Server security

  - by Frans

  Using Windows Server 2008. I would like to allow all users to map to a common network drive and be able to browse it. But, I only want them to be able to see the subfolders they actually have access rights to. Is this doable? Example I have a share with two folders on it; \\domain\share\FolderA \\domain\share\FolderB With three different security groups, I would like to map a network drive for all three to \\domain\share. However, for group1, I want them to only be able to see FolderA, group2 should only see FolderB and group3 should see both. I am not just talking about denying access to the actual folder, which is easy enough, I don't want the user to even be able to see that the folder exists. In other words, when group 1 logs in and do "dir n:\" they should see N:\FolderA When group 2 logs in, they should see N:\FolderB and when group 3 logs in they should see N:\Folder A N:\Folder B My half-baked solution If I completely block access to the root then I can't map a drive to it. I can give everyone the traverse right which then allows the user to map a drive. However, if a member of group1 or group2 tries to go to "N:\" they get an access denied error. If they go to N:\FolderA (for group1) then it works. So, that sort of works, but it would be nicer if the user could actually browse to N:\ and just only see the subfolders they have access to. I am pretty sure I have seen this done but not sure how to do it myself. Any advice would be greatly appreciated.

  Read the article

• "Enter/Return" Key with Word Mobile on Windows Mobile

  - by Maarx

  Some of our employees are using PDAs running Windows Mobile. I wish I could provide more data regarding versions, but frankly these things aren't my jurisdiction. Someone's simply come to me looking for what they thought would be a quick fix. They're using Word Mobile and the barcode scanner to record large volumes of data. The scanner's default action is to insert the scanned text exactly as if it had been input with the keyboard, and puts a newline at the end. That's great, because it's exactly what we need it to do: separate data with newlines. The issue comes when system can't read the barcode, and the employee has to type in the data by hand. They've discovered a very peculiar quirk of Mobile applications: pressing the hardware Enter/Return key on the keyboard appears to save and exit the application. How do we change this behavior? They've realized that using the stylus to "click" the virtual on-screen keyboard's Enter/Return key will add the necessary newline, but it's a huge inconvenience for them. How do I fix the default behavior of the Enter/Return key for Word Mobile to instead insert a newline?

  Read the article

• Cross-forest universal groups on Windows Server?

  - by DotGeorge

  I would like to create a Universal Group whose members are a mix of cross-forests users and groups. In the following example, two forests are mentioned (US and UK) and two domains in each forest (GeneralStaff and Java): For example, the universalDevelopers group may comprise of members from UK.Java.Developers and US.Java.Developers. Then, for example, there may be a group of universalSales which contains the users UK.GeneralStaff.John and US.GeneralStaff.Dave. In UK forest at the minute, I can freely add members and groups from the UK. But there is no way to add members from the US forest, despite having a two-way trust in place... e.g. I can login with US members into UK and vice-versa. A further complication is that, with a Universal group in the UK (which contains three domains), I can only add two of the three. It can't see the third. Could people please provide some thoughts on why cross-forest groups can't be created and ways of 'seeing' all domains within a forest. EDIT: This is on a combination of Windows 2003 and 2008 server. Answers can be regarding either. Thanks!

  Read the article

< Previous Page | 359 360 361 362 363 364 365 366 367 368 369 370  | Next Page >