Search Results

Search found 91524 results on 3661 pages for 'new it manager'.

Page 364/3661 | < Previous Page | 360 361 362 363 364 365 366 367 368 369 370 371  | Next Page >

  • startx doesnt run gives an error xauth unable to link authority files

    - by Sandeep
    I have installed windows xp on VPC and have installed cygwin-x on that virtual machine. When i run startx command. I get the following error: xauth: creating new authority file /home/Administrator/.serverauth.1480 xauth: unable to link authority file /home/Administrator/.serverauth.1480, use /home/Administrator/.serverauth.1480-n xauth: creating new authority file /home/Administrator/.Xauthority xauth: creating new authority file /home/Administrator/.Xauthority xauth: unable to link authority file /home/Administrator/.Xauthority, use /home /Administrator/.Xauthority-n xauth: creating new authority file /home/Administrator/.Xauthority xauth: creating new authority file /home/Administrator/.Xauthority xauth: unable to link authority file /home/Administrator/.Xauthority, use /home /Administrator/.Xauthority-n giving up. xinit: No such file or directory (errno 2): unable to connect to X server xinit: No such process (errno 3): Server error. xauth: creating new authority file /home/Administrator/.Xauthority

    Read the article

  • startx doesnt run gives an error xauth unable to link authority files

    - by Sandeep
    I have installed windows xp on VPC and have installed cygwin-x on that virtual machine. When i run startx command. I get the following error: xauth: creating new authority file /home/Administrator/.serverauth.1480 xauth: unable to link authority file /home/Administrator/.serverauth.1480, use /home/Administrator/.serverauth.1480-n xauth: creating new authority file /home/Administrator/.Xauthority xauth: creating new authority file /home/Administrator/.Xauthority xauth: unable to link authority file /home/Administrator/.Xauthority, use /home /Administrator/.Xauthority-n xauth: creating new authority file /home/Administrator/.Xauthority xauth: creating new authority file /home/Administrator/.Xauthority xauth: unable to link authority file /home/Administrator/.Xauthority, use /home /Administrator/.Xauthority-n giving up. xinit: No such file or directory (errno 2): unable to connect to X server xinit: No such process (errno 3): Server error. xauth: creating new authority file /home/Administrator/.Xauthority

    Read the article

  • Page numbers in Word 2007

    - by ldigas
    I'm gonna skip the usual rant which normally follows upon mention of the words "Word 2007" I have a numbered section. Which has page numbers. Then, I insert a new section break at the end of the current section ... go to page numbers, format ..., and "start at ...", and the new section then has a new page numbering (starting with some other number). But, how do I after inserting a new section break, remove the page numbering in the new section ? If I go to remove page numbers option, Word removes the numbers from the new, but also from the old section (i.e. all of them). Help ... time is short ...

    Read the article

  • Can't the NetworkManager applet to appear in the Gnome panel in Ubuntu

    - by Nate
    I have researched this problem extensively and I can't seem to find an answer. In Ubuntu 10.04 LTS, I want to connect to my VPN through the NetworkManager applet. I installed all the network manager packages, including the gnome client. I understand I need to add the "Notification Area" to the panel, which I have done. I checked that the NetworkManager is running: nate@nate-desktop:~$ service network-manager status network-manager start/running, process 763 In /etc/NetworkManager/nm-system-settings.conf, I have added managed=true (don't know if this matters, but I saw it suggested on one forum): nate@nate-desktop:~$ more /etc/NetworkManager/nm-system-settings.conf # This file is installed into /etc/NetworkManager, and is loaded by # NetworkManager by default. To override, specify: '--config file' # during NM startup. This can be done by appending to DAEMON_OPTS in # the file: # # /etc/default/NetworkManager # [main] plugins=ifupdown,keyfile [ifupdown] #managed=false managed=true At this point, it looks like NetworkManager is running but it's not appearing in the NotificationArea of the panel. I don't know what else to try. Any ideas?

    Read the article

  • Can't the NetworkManager applet to appear in the Gnome panel in Ubuntu

    - by Nate
    I have researched this problem extensively and I can't seem to find an answer. In Ubuntu 10.04 LTS, I want to connect to my VPN through the NetworkManager applet. I installed all the network manager packages, including the gnome client. I understand I need to add the "Notification Area" to the panel, which I have done. I checked that the NetworkManager is running: nate@nate-desktop:~$ service network-manager status network-manager start/running, process 763 In /etc/NetworkManager/nm-system-settings.conf, I have added managed=true (don't know if this matters, but I saw it suggested on one forum): nate@nate-desktop:~$ more /etc/NetworkManager/nm-system-settings.conf # This file is installed into /etc/NetworkManager, and is loaded by # NetworkManager by default. To override, specify: '--config file' # during NM startup. This can be done by appending to DAEMON_OPTS in # the file: # # /etc/default/NetworkManager # [main] plugins=ifupdown,keyfile [ifupdown] #managed=false managed=true At this point, it looks like NetworkManager is running but it's not appearing in the NotificationArea of the panel. I don't know what else to try. Any ideas?

    Read the article

  • How to install software packages on a shared Red Hat Linux host account without root access or rpm?

    - by jeff
    I have a shared RHEL 4 host account where I do not have root privileges. I would like to install Git and Bash Complete in a way that they can be upgraded easily. To date, I've just been installing from source providing $HOME as a prefix to autoconf. Obviously this isn't ideal as I need to hunt down the files associated with the version I'm upgrading away from and delete them. I've tried using rpm but I just get -bash: rpm: command not found back so it's not available. I also looked into checkinstall but it looks like that requires rpm, dpkg, or Slackware's package manager to be available. Is there anything out there that can be used like a package manager without requiring root access or an existing package manager?

    Read the article

  • Easy Transfer from a dead computer

    - by Nathan DeWitt
    I had a computer that electrocuted me and the company sent me a new one. The hard drive from the old computer works fine and is in my new computer. I would like to transfer my files from the old drive to the new one, preferably using Easy Transfer (old & new computers were Win7). When I go through the Easy Transfer wizard, it assumes my old computer is running and that I can run a process to backup all my data to a single file. However, in my case I have the system drive in my new computer and want to pull the data off it. I would like to avoid rebooting the old computer, to avoid damage to myself or my data. I would like to avoid booting into the old system drive, as my new hardware is significantly different and I imagine I'll run into some missing hardware issues. What's the easiest way to get my data off this drive?

    Read the article

  • Create private key with CSR

    - by Daniel Schlieckmann
    I have a CSR file (as a text file) and the corresponding P7B certificate. My problem is that I have to create a P12 file on a machine where I do not have created the CSR. I have created the CSR in Firefox Key Manager. Before, I imported the P7B file into certificate store in msc, then exported a CER-file, imported it in Key Manager and then exported the P12 file. This doesn't work anymore because I have another machine now. If I try to import the CER file created by msc, Key Manager says that there is no private key. Is there a possibility to create a private key?

    Read the article

  • Cannot start `Routing and Remote Access Service` and it's dependencies

    - by ahmadali shafiee
    I tried to start Routing and Remote Access Service but I've got an error says the dependency service or group failed to start then I tried to start Remote Access Connection Manager (one of RRAS's dependencies) and the error way same. then I tried to start The Secure Socket Tuning Protocol Service but there was an error says that the the service started then stopped! the errors form event log is here: The Remote Access Connection Manager service depends on the Secure Socket Tunneling Protocol Service service which failed to start because of the following error: The operation completed successfully. The Secure Socket Tunneling Protocol Service service entered the stopped state. The Routing and Remote Access service depends on the Remote Access Connection Manager service which failed to start because of the following error: The dependency service or group failed to start. sort by date Does anyone know how can I resolve the problem?

    Read the article

  • Using windowmaker with quartz-wm in proxy mode on Snow Leopard

    - by Graham Lee
    I can modify my .xinitrc file to exec /opt/local/bin/wmaker, and get WindowMaker 0.90.2 as my window manager in X11.app. I'd like to use quartz-wm not as a window manager, but to provide the pasteboard integration with Aqua using the --only-proxy flag (see the man page). If I add the following line to .xinitrc: exec /usr/bin/quartz-wm --only-proxy & then WindowMaker never starts, complaining that there's already a window manager running. Is it possible to get the two to play nicely together, or is proxy feature part of the Xquartz server now? It seems that the Xquartz manpage has a number of pasteboard-to-clipboard synchronisation settings, but it's not clear whether quartz-wm needs to be running for those to work.

    Read the article

  • How to automatically show USB camera or memory stick contents in Icewm?

    - by darenw
    I normally use a very lightweight Linux setup. No desktop like Gnome or KDE, just Icewm as the windows manager and nothing else that normal users might consider essential. Well, I do need a file manager - I use Thunar. Recently I've been trying Gnome. Whenever I shove a memory stick into a USB port, or connect my digital camera, it can automatically pop up a file manager showing all the goodies on that device. KDE does this too. I like this. Although quick at the command line, I like not having to go sudo to mount the device and all that. If I want to stick with a lightweight setup using Icewm+Thunar, is there something non-huge I can install to make external devices fire up a Thunar window, or otherwise make access to the contents brainlessly easy?

    Read the article

  • Windows XP Home Edition SP3 cant recognise PCMIA SD Card

    - by Pozo
    System Specifications: Laptop : Dell Inspiron 6000 OS: Windows Home Edition SP3 SD Adapter: Hagiwara Smart Media Adapter I inserted the card into the slot, windows xp recognises the device, lists the pcmia controller on the device manager list, an entry appears under the IDE ATA/ATAPI category on the device manager as well. However, the device does not show under my computer and the driver does not get assigned a letter number. I checked the system logs from the device manager and there were no logged errors. Checking the Hagiwara support website, the manufacturer indicates that the adapter driver is the same as the windows xp pcmia controller. Checking Dell's website, no specific drivers were listed for that either. General Search on the web indicates that multiple people face similar problems with their SD cards, yet none actually spell out the route issue that causes this. Please let me know if you have any suggestions for further debugging. Thanks in advance

    Read the article

  • Wireless router not connection -> AP Not associated

    - by candido
    I can not connect to internet by wireless router after some months with ubuntu 10.04. I can connect with the same portable but with win OS. My SO is ubuntu 10.04 linux 2.6.32-41 arch SMP i686. The internet wireless network controller is Atheros AR9285 chipset (pci express) Kernel module ath9k I have tried a command line connection: $ sudo /etc/init.d/network-manager stop #stop gui network manager $ iwconfig wlan0 essid WLAN_3C key s:C001D20550B3C $ ifconfig Access Point: NOT-ASSOCIATED $dmesg ... AP 00:1a:2b:08:60:49 associated Is the SO has connected to router for booting long ( associated message), after boot and login why the connection to router is not possible by network-manager or command line (NOT associated message)? Thanks in advance

    Read the article

  • hyperv machine guest loads slow

    - by Dani Avni
    this is by far one of the strangest things I have seen. I have a win 2008R2 cluster with a CSV. the CSV itself is on an iSCSI storage (hitachi HUS 110) basic config of the two hosts in the cluster is Dell R610 Win 2008 R2 with all patches 64GB 1 NIC for host access 2 NICs for guest access 2 NICs for iSCSI these machine work great and I can load a 2008R2 test guest machine on them in less than 90 seconds after the above config is running for over a year, I now need to add a new host. now the host is Dell R620 (Still intel but different CPU) Win 2008 R2 with all patches 64GB 1 NIC for host access 2 NICs for guest access 2 NICs for iSCSI I added this new host to the domain and to the cluster, I gave it access to the CSV and I tried loading the same guest machine that loads in 90 seconds in the other hosts. the machine loads in about 6 minutes. no matter how many times I try this the old hosts load the machine in about 90 seconds and this new host in around 6 minutes to eliminate any problems with the iSCSI connection, I added a new LUN and directly accessed it from the new host and I was working at around 300MB/s so no problem there. I also tested the connection between the other hosts and the new one and network is working fine there too. to eliminate problems in HyperV, I copied the machine to the local disk of the new host and it loaded in less than 20 seconds. now is the point were things get a lot stranger: in my tests I tried installing a fresh windows guest machine to the CSV from the new host. I noticed that while the fresh windows was installing, my test guest was loading in less than 90 seconds even on the new host (I repeated this a few times). If I paused the fresh install guest and tried loading the test guest again it loaded in 6 minutes. and again after I resumed the guest installation the test guest loaded fast. after the fresh windows was also loaded, I ran tests loading the fresh window and my test machine. each one of them loaded in about 5 minutes when I tried loading them separately. however when I started both of them in the same time they both loaded in around 2.5 minutes it seems that the iSCSI disk access is only working if it is under some load (although I never got to above 10% utilization according to the task manager) does anyone have any idea what could be the problem?

    Read the article

  • Speakers will not work after I use USB Headset

    - by Josh K
    I am trying to configure my SteelSeries Siberia V2 Frost USB Headset to work with my 2.0 speakers using a jack. My goal is to find a easy way (no restart) to switch playback from my headset and my speakers and vice-versa. If i plug my headset in and make it the default device then restart my application/web page then the sounds works out of headset. If I switch the default to my speakers and restart apps/web pages then sound does not play. I know my speakers are on because if I configure them through windows and test, the sounds play, and sounds also play when I test it through my audio manager. Even if I unplug my headset, I still cannot get sound out of my speakers unless I restart My audio manager is RealTek HD Audio Manager, Windows 7 x64. I have tried the speaker back, usb front. speaker front, usb in front port. I have not tried speaker back, usb back.

    Read the article

  • Transport rule - Exchange 2010

    - by Jeff
    I have two transport rules on my exchange server. One is: > Apply rule to messages: From users that are 'outside the organization' > and when any of the recipients in the To or Cc fields is a member of > '[email protected]' Forward the messageto sender's manager > for moderation The second is: Apply rule to messages from a member of '[email protected]' and sent to users that are 'outside the organization' forward the message to the sender's manager for moderation. nointernetmail is a distribution group, and each user has the managed by set to there local manager. However these transport rules do not work, internet mail is still sent and received without issue. I have read various tutorials / articles of how to do this on sites such as msexchangeblog and even microsoft technet, however even after following the guides I am still unable to have this function properly. Any help is appreciated.

    Read the article

  • Let task explorer always run with realtime priority

    - by Simon Verbeke
    I have replaced task manager by process explorer from sysinternals. I would like this to always run at realtime, so that I can easily get it open when my system is really slow. I have noticed that it can take a while to start this program at those moments. I have gone over the different options mentioned on SU. I can't change the shortcut, it immediately opens the .exe. I also can't use the task manager plugins/extensions, as I'm not using task manager. Any idea what I could do? Preferably without installing any other software. That is, if the priority would have any effect on starting the program.

    Read the article

  • How to modify Chrome newtab.css from within a Chrome theme?

    - by user143423
    I want to modify the CSS for new tab page. NOT make new tab page. I already made a new tab page, but many users installing my themes won't also install the new tab page extension. So I want to modify the CSS on the new tab page for those who ONLY want my theme. It is my understanding that chrome://theme/css/newtab.css is the stylesheet I need to change. Feel free to tell other ways to add CSS to the ORIGINAL new tab page in Chrome.

    Read the article

  • Exchange Server 2003 Drive Error

    - by Saif Khan
    My exchange box went offline this AM. The logs show The device, \Device\Harddisk1, has a bad block. I tried running chkdsk D: /x /r but that didn't help either. I went to the Exchange Manager and tried to move the .stm file from D: to C: but got Exchange System Manager The database files in this store are corrupted. ID no: c104173b Exchange System Manager What else is there to try just to get this online for a few hours until I can get onsite to change the drive. This is a Windows Server 2003 server.

    Read the article

  • moving my site, IP change worries...

    - by Sherif Buzz
    Hi all, my site has outgrown the shared hosting account it's on and i've setup a VPS that i'll be moving to soon. I cannot keep the same IP between my new account and the old one and I'm a bit at loss as to how to minimize user downtime while the new IP is reflected in all DNS caches. Note I cannot have the site running on both accounts at the same time as it's a dating site and this would cause data inconsistency. Here's what i am planning to do : Put up a 'under maintenance' page on old host Get the site up and running on new host, and update domain to point to new host. Hope downtime isn't too long. Would it be a good idea to have a link on the page in (1) that opens the new site but using it's ip ? Or even redirect all requests at the old host, to the new one (again by ip) ? Any advice much appreciated.

    Read the article

  • RedirectPermanent vs RewriteRule [R]

    - by notbrain
    I currently have a perm_redirects.conf file that gets included into my apache config stack where I have lines in the format RedirectPermanent /old/url/path /new/url/path It looks like I'm required to use an absolute URL for the new path, e.g.: http://example.com/new/url/path. In the logs I'm getting "incomplete redirect target /new/url/path was corrected to http://example.com/new/url/path." (paraphrased). In the 2.2 docs for RewriteRule, at the bottom they show the following as being a valid redirect, with only the url-paths instead of an abs URL for the right hand side of the redirect: RewriteRule ^/old/url/path(.*) /new/url/path$1 [R] But I can't seem to get that format to work to replicate the functionality of the RedirectPermanent version. Is this possible?

    Read the article

  • How to monitor RAM usage for Hyper-V VMs ?

    - by Mac
    A bit of context first : on Windows 2008 Standard x64 with 8Gb RAM, I have 5 VMs running which should take up 1664Mb RAM (3*256Mb+384Mb+512Mb). There is nothing else running on this server except the basic OS components (this not a Core installation). I know that each VM will use more RAM on the host than what has been configured in Hyper-V. But when I run the task manager, it says 6.7Gb used ! If I sum up the RAM used by each process in the task manager (showing all users processes), I get to something around 1Gb... So : how can I check how much RAM each VM is really using on the host (it does not seem to be available via task manager) ? Note that I am aware of the fact that my problem could be unrelated to VM RAM usage, but I would still very much like to know how to do this.

    Read the article

  • Temporarily disable window snapping in xfce4

    - by icyrock.com
    I'm using Xubuntu 12.04 and I can move windows by pressing Alt and then dragging a window. I have window snapping enabled via xfce4-settings-manager (Window Manager / Advanced tab / Snap windows to screen border). I like the snapping feature in general, however sometimes it gets in the way. Is there a way to temporarily disable snapping while doing this? Obviously I can open the settings manager, disable, move, enable, but I'm looking for a less intrusive solution, especially if there's something built in already (e.g. pressing Shift in addition to Alt to disable snapping or something along these lines) or a plugin of some sorts.

    Read the article

  • SQL Server 2008 (64-bit)

    - by Grace09
    I have transaction log backup failures randomly. SQL Server Log says 'Memory constraints resulted reduced backup/restore buffer sizes. Proceding with 6 buffers of size 64KB.', and the SQL Server Agent Error Log has quite a few errors like 'Unable to start Job Manager thread for job xxx', '[298] SQLServer Error: 768, Client unable to establish connection [SQLSTATE 08001]', [298] SQLServer Error: 768, SSL Provider: Not enough memory is available to complete this request [SQLSTATE 08001]'. I am really low on the memory? It has total of 32 GB, but I set maximum to 20. Task manager shows it is using 99% of physical memory. Memoryclerk-sqlbufferpool has 32GB for the Virtual Memory Reserved, and 20 GB for the Virtual Memory Committed. From the perfmon, SQLServer:Memory Manager/Total ServerMemory shows 21GB of memory in use, that's what I set the maximum to. I don't where the rest of memory go. Can anyone advice? Thanks in advance.

    Read the article

  • How do you mock ViewModel Commands using moq?

    - by devnet247
    Hi I might be approaching this all wrong.But please help me to understand. I really want to TDD building wpf application using Moq. I would like to mock the viewmodel. Application Show a list of contacts and when you double click on a contact it shows the contact. Test Moq GetContactsCommand.Test it has been called. Test that you get a list of contacts. Not sure how to mock the viewModel and it's commands can you correct me? So I have started to do the following [Test] public void Should_be_able_to_mock_getContactsCommand_and_get_a_list_of_contacts() { //Arrange var expectedContacts = new ObservableCollection<ContactViewModel> { new ContactViewModel(new ContactModel { FirstName = "Jo", LastName = "Bloggs", Email = "[email protected]" }), new ContactViewModel(new ContactModel { FirstName = "Mary", LastName = "Bloggs", Email = "[email protected]" }) }; var mock = new Mock<IContactListViewModel>(); mock.SetupGet(x => x.GetContactsCommand).Verifiable(); mock.SetupGet(x => x.Contacts).Returns(expectedContacts); //Act //? //assert mock.VerifySet(x => x.Contacts, Times.AtLeastOnce()); mock.Object.Contacts.Count.ShouldEqual(expectedContacts.Count); } public interface IContactListViewModel { ObservableCollection<ContactViewModel> Contacts { get; set; } ICommand GetContactsCommand{ get; } } public interface IContactModel { string FirstName { get; set; } string LastName { get; set; } string Email { get; set; } } public class ContactModel : IContactModel { public string FirstName { get; set; } public string LastName { get; set; } public string Email { get; set; } } public class ContactViewModel : ViewModelBase { private readonly ContactModel _contactModel; public ContactViewModel(ContactModel contactModel) { _contactModel = contactModel; } public string FirstName { get { return _contactModel.FirstName; } set { _contactModel.FirstName = value; OnPropertyChanged("FirstName"); } } public string LastName { get { return _contactModel.LastName; } set { _contactModel.LastName = value; OnPropertyChanged("LastName"); } } public string Email { get { return _contactModel.Emai; } set { _contactModel.Email = value; OnPropertyChanged("Email"); } } } public class ContactListViewModel : ViewModelBase, IContactListViewModel { private ObservableCollection<ContactViewModel> _contacts; public ObservableCollection<ContactViewModel> Contacts { get { return _contacts; } set { _contacts = value; OnPropertyChanged("Contacts"); } } private RelayCommand _getContactsCommand; public ICommand GetContactsCommand { get { return _getContactsCommand ?? (_getContactsCommand = new RelayCommand(x => GetContacts(), x => CanGetContacts)); } } private static bool CanGetContacts { get { return true; } } private void GetContacts() { //pretend we are going to the service or db whatever Contacts = new ObservableCollection<ContactViewModel> { new ContactViewModel(new ContactModel { FirstName = "Jo", LastName = "Bloggs", Email = "[email protected]" }), new ContactViewModel(new ContactModel { FirstName = "Mary", LastName = "Bloggs", Email = "[email protected]" }) }; } }

    Read the article

< Previous Page | 360 361 362 363 364 365 366 367 368 369 370 371  | Next Page >