Search Results

Search found 57569 results on 2303 pages for 'windows scheduler'.

Page 367/2303 | < Previous Page | 363 364 365 366 367 368 369 370 371 372 373 374  | Next Page >

• Getting 2560x1600 out of an ATI Radeon HD 4670 on Windows 7

  - by Alexey

  Greetings, I've got a Dell Studio XPS 1640 laptop (with an ATI Radeon HD 4670 graphics card) running Windows 7, and just bought a Dell 3007HPC 30-inch monitor for it. I'm trying to figure out how to get the full 2560x1600 experience out of this setup. Here's what I've done so far: Plug in using an HDMI cable and an HDMI--D-DVI converter on the monitor side. Open up Screen Resolution. Maximum supported setting is 1920x1080. Tried that (several times) - sometimes it doesn't work at all (blank screen); other times, it only shows the first 1280x800 pixels on the bigger screen. Tried using the Catalyst control center - played with various settings there, couldn't get the screen to show anything interesting. Tried using PowerStrip to set a custom resolution, again, no luck. Spoke to a Dell Preferred Custom Support guy for about an hour before giving up. He remote-accessed my computer, and told me that (1) The maximum supported resolution for XPS 1640 is 1920x1080, and (2) 'it seems to be working from where he sees it, must be a connection issue'. None of this has helped. Does anybody have ideas? Should I be using a different cable set up? Am I using Powerstrip wrong?

  Read the article

• Windows Server 2003 DC hangs after network drivers update

  - by tcv

  Earlier today, we attempted to update the Broadcom BCM5716C network drivers on a Windows Server 2003. (Dell PowerEdge T310, FWIW). Since then we have not been able to boot the server in any normal mode. Safe Mode works. Safe Mode with Networking and regular bootups hang at "Applying Network Settings." I haven't tried Last Known Good Configuration nor have I tried Directory Services Restore Mode. I should also mention that the longest I've allowed "Applying Network Settings" was perhaps 30 minutes. I spoke to Dell since the server is under a basic warranty. They sent me the original Broadcom drivers. The trouble seems to be, however, that since I can only boot in Safe Mode, I can't install the application package as given. In safe mode, I receive the error: "The system administrator has set policies to prohibit this installation." I can install the drivers independently, but that doesn't allow the NICs to work. The most I've been able to get are Code 10 errors on each NIC. I plan to get back to the site tomorrow to attempt installation of a different NIC. I'm wondering what else I can try.

  Read the article

• Windows 7 Blank Screen on Boot / Login

  - by Greg

  I have a new system that's having a few problems... sometimes (seems to be when the PC is cold, i.e. has been switched off for a while, though that could be my imagination) I get a blank blue screen when I boot up. The system boots normally and auto-logs-in. The desktop loads and I'm even able to launch applications, but then everything disappears and the screen goes to the default windows desktop blue colour (not the desktop image, just a plain blue with no mouse cursor). At this point the machine completely locks up - I'm unable to even toggle Num Lock and have to hold in the power button for 5 seconds to kill it. Interestingly if I manage to launch some applications before it goes blank, they will usually crash... sometimes explorer.exe will crash too. When I reboot, the system is fine and stable. I've installed the latest graphics drivers and run memtest86+ for 6 passes (and counting) with no errors. The system specs are: CPU: Intel I7 2.66 @ 3.4GHz RAM: 6GB (3 * 2GB DDR3) HDD: 128GB Crucial M225 SSD Motherboard: Gigabyte EX58-UD3R Gfx: ATI Radeon Sapphire 5870 1GB Note: There are a few similar questions but I haven't found one that matches my symptoms

  Read the article

• Possible DNS issue after a reinstall of Windows Server 2000 (get off my lawn)

  - by cop1152

  I just replaced a drive on a Win2000 Server that replicates AD and issues out DHCP at one of our offices. I successfully joined it to the domain, setup range of IP's, etc, but am still having issues. I cannot RDC to it with name or IP. I can ping it, browse to it with Windows Explorer, and remote to it with some other software, but not RDC. The other issue is this: Users are unable to authenticate on it. They receive the message 'username or password incorrect' (or something like that). Changes made on the main domain controller seem to take forever to trickle down. The most significant entry in the DNS Server Log is Event ID 7062: The DNS Server Encountered a Packet Addressed to Itself. At least, I think its significant. The Directory Services Log shows numerous Event IDs 1265: The attempt to establish a replication link with parameters failed with the following status: The DSA operation is unable to proceed because of a DNS lookup failure. Does this make any sense to anyone? I feel like its something very simple that I am overlooking. Thanks in advance.

  Read the article

• Windows Phone 7 Development &ndash; Useful Links

  - by David Turner

  Here are some excellent links for anyone developing for Windows Phone 7: J.D. Meier’s Windows Phone Developer Guidance Map – this is immense.  Also check out the Silverlight version Justin Angel’s site – some really great articles on unlocked roms, automation and Continuous Integration Windows Phone 7 Development Best Practices Wiki Jeff Blankenburg’s 31 days of Windows Phone 7 This post of Links to sample code for Windows Phone Tim Heuers blog, particularly this post of Tips and Tricks Kevin Marshall's blog, particularly the epic WP7 Development Tips Part 1 post Code Samples for Windows Phone on MSDN If you have unlocked your phone for development, then you can use the WPConnect tool to connect to the device rather than using the Zune client.  I found it useful to pin a shortcut to WPConnect in my Start Menu. The Performance Counters displayed when you debug your app on a device are useful for seeing things like frame rate and memory usage, this page on MSDN explains what the numbers mean.  Jeff Blankenburg covers this in more details on his blog I also came across this set of links to tutorials recently which looks very useful. Creating Windows Phone 7 Application and Marketplace Icons: http://expression.microsoft.com/en-us/gg317447.aspx

  Read the article

• User cannot access a system DSN on Windows Server 2008

  - by Ra Osolage

  We run our SQL Server services using a low privileged domain account. That account is NOT a local admin on the OS. Only access I give the user account is assigned during install of SQL: full control over its mount points and then everything else is granted by the SQL Server 2005/2008 installer. I need to create a linked server in SQL Server 2008 to an ODBC data source. So I remoted into the computer using my domain account, which is part of a group that DOES have local admin privs to the OS. I created a system DSN and configured it to connect to another SQL Server. The DSN works perfectly when I test it. However, when I try to create the linked server, I get an error. It appears to me that the DSN is invisible to the domain account that SQL Server is running as. It seems that this problem is only happening to me on Windows 2008 servers. Does anybody know whether there's anything that you need to do after creating a DSN to make it visible for other users to access?

  Read the article

• Backup hardware and strategy on distributed Windows Server 2008 network

  - by CesarGon

  This question is a follow up to this. We have a Windows Server 2008 R2 domain over a network that spans two different buildings, linked by a 100-Mbps point-to-point line. Over 60 users work in the organisation. We are planning to use DFS folders and DFS replication for file serving across the organisation. The estimated data volume is over 2 TB, and will grow at approximately 20% annually. The idea is to set up a DFS file server in each building and use DFS so that all the contents stay replicated over the 100-Mbps link. We are now considering backup hardware and strategies. We are Dell customers and, after browsing the online Dell catalogue, I can see a number of backup hardware options. My main doubts are the following: Would you go for a tape library, disk backup, or are there other options worth considering? Would you perform batch backups (i.e. nightly) or would you use continuous backup (i.e. while users are working)? Would you use a dedicated backup server to which the tape library (or any other backup device) is attached, or is there any other alternative way of doing things? My experience with backup hardware and overall setup is limited, so I appreciate any good piece of advice that you may have. Thanks.

  Read the article

• Problems with word completion on Windows Mobile

  - by Rowland Shaw

  For "some reason" the word completion function on my windows mobile phone (HTC Diamond, rebadged as a T-Mobile MDA Compact IV (UK) running WM6.1 with HTC Touch Flo 3D) hasn't worked since one of my firends was taking a look at the phone (I remember him bitching about it being too obtrusive for him, as an iPhone fanboy). I've checked all the obvious settings ( Start Input Word Completion ) and everything looks set there; I tried a hard reset, to no avail and even tried upgrading the ROM t the latest from my network provider. I even tried walking into the store where I bought the phone, and the staff couldn't fix the issue. I still have my old handset, which also runs WM6.1 (a T-Mobile MDA Compact III (UK), albeit without Touch Flo 3D), and the word completion works on there, so I'm a little confused as to why I can't get it to work again on my new handset. Can anybody identify why this might not be working, or help me fix it? Edit: Even "Touch Input Settings" has both "Word Completion in T9 mode" and "Word Completion in ABC mode" checked. The full qwerty keyboard option is in T9 mode, and word completion works for this input method; It still does not work for my preferred, "Letter Recogniser" method.

  Read the article

• Application to automate Windows software installation in a test lab

  - by Marc

  I have several test environments (hyper-V) which contain a variety of windows servers. Each machine needs periodically rolling back to a given snapshot and then re-installing with the latest version of our software to test. The software installs are quite complex MSI's with a fair few option screens. I know that the installs can be driven from the command line, passing in parameters to override the wizard options. At the simplest level I suppose I could just write a batch file to kick off each install with the required parameters, however the values that are passed in do need to change from time to time (and environment to environment) so a tool with a config file and simple GUI seems like a better idea. I think what makes it slightly more painful is the multiple environments. For example one environment might contain 4 servers and need a config file with all the server names, service endpoints etc. Another environment might be a 1-box install with all names and endpoints set to localhost. So, ideally I want to be able to store different setup configurations and use them to run all the required installers with the relevant settings against the relevant machines. Before I go off to write the thing, does anyone know of an existing, simple, free tool that will let me achieve this?

  Read the article

• No LPT port in Windows 7 virtual machines

  - by KeyboardMonkey

  Windows 7 has MS virtual PC integrated, the VM settings don't give a parallel LPT port mapping to the physical machine. Where did it go? Has anyone else noticed this, and found a solution? Update: After much digging, I found the one and only reference to this issue, on the VPC Blog: "Parallel port devices are not supported, as they are relatively rare today." -More details- It's a XP VM I've been using since VPC 2007 days, which did have this functionality. This is to configure barcode printers via the LPT port. Since the (new) MS VM can't map to my physical LPT port, I'm having a hard time configuring printers. My physical ports are enabled in the BIOS. It has worked the past 3 years, before switching to Win 7. Any help is appreciated. This screen shot of the VM settings shows COM ports, but LPT is no more In contrast, here is a screen shot of VPC 2007 (before it got integrated into Win 7). Notice how it has LPT support

  Read the article

• Sluggish Windows SBS 2003

  - by TomWilsonFL

  One of my customers has a Windows 2003 Small Business Server which at this point is basically the DC, DNS, Fileserver and Symantec Protection Manager. I have disabled Exchange because I moved their mail to Google Apps. The server is extremely sluggish when doing anything. It is most noticeable when a dialog box is open (say the System properties), and you try to change tabs. This is usually instant, but on this machine can take 3-5 seconds. What additional services / packages can I uninstall from this machine knowing that it is only performing the above roles? Will removing the "Small Business Server" package in Add / Remove Programs get rid of a few unnecessary things? Any other thoughts? P.S. I know Symantec Endpoint and the Protection Manager are hogs, but I have nothing to replace the solution with at the moment. Thanks, Tom UPDATE: I looked over the different performance metrics, but nothing stood out as a problem. One of my friends mentioned Symantec's log and temp files can get quite huge and slow things down, so I ran CCleaner on the machine and found close to 3 GB of Symantec "stuff." Removed that and now the machine is MUCH better. I am still unsure why the data just sitting there would cause such a slowdown. The drive is not even near full. The only thing I can imagine is that Symantec must have to run through this stuff now and then.

  Read the article

• Windows Vista: Folder options not working

  - by Thomas Matthews

  I'm running Windows Vista Service Pack 2. I have the Folder Options set to "Open each folder in the same window." (Organize | Folder Options | General). Each time I open a folder, it opens in a new window. How do I get it to open each folder in the same window? I have tried the following techniques with no success: 1. Expand number of MBAG entries in Registry. (The number is 40,000 now.) 2. Delete Bags and MBAG entries in Registry. (Rebooted machine after, still no success). 3. Change to "Open each folder in its own window". Saved, then changed back. 4. Under View tab, changed "Remember each folder's view settings": unchecked, Apply to Folders, checked, Apply to folders. 5. Applied application from Annoyances.org. Still no success. 6. Clicked on Reset Default Options, then OK. (Opening in same fold is a default option!) Still unsucessful. I want the folders to open in the same window, just like the options say.

  Read the article

• Silent install FirePro v4900 Driver on Windows Embedded 7 Standard

  - by Birgit_B

  I'm trying to install the Drivers for a FirePro v4900 on a Windows Embedded 7 Standard 64bit OS. I want the system to be as small as possible, so i would rather not install the whole catalyst control center, but only the necessary drivers. Because the installation should be accomplished absolutely unattended, the installation process of the FirePro-Driver should also be done without any user interaction. I see two possible solutions for the Problem: Install only the Drivers: Is it possible to solely install the necessary drivers? How would i achieve that? This solution would be the preferred one, because of the smaller footprint. Silent custom install the provided "FirePro_8.911.3.3_VistaWin7_X32X64_135673.exe" (found at ATI FirePro™ Driver). Is there a way, to do that? Thank you in advance for your support! Update: I managed to accomplish a silent installation. I extracted the contents of the above mention installer-file and ran \$_OUTDIR\Bin64\Setup.exe -Install. (There are some other Parameters, just run Setup.exe /?). But i couldn't achieve to just install the drivers without the Cataclyst Control Center, and it seams the Control Center has some unfulfilled dependencies and so it crashes...

  Read the article

• windows clients cannot get dns resolution until you open and close ipv4 properties page

  - by GC78

  This strange problem has started recently. Some windows clients cannot seem to get dns resolution to the internet after boot, and sometimes again at some point in the day. Internal hosts are also slow to resolve. trying to ping an interal host by name will take a long time for the hostname to resolve to ip address and trying to ping a website by name will fail to resolve. If you go into the tcp/ip v4 properties and view but not change anything, ok/close out of that then the client starts working fine, hostnames will resolve quickly. I have seen this happen on both Vista and W7 clients. ipconfig /all at a client experiencing this problem shows everything in order. proper ip addr, gateway, dns server, dns suffix ect.. ipconfig /dnsflush will not fix them, neither will /release and /renew the clients get their ip address, mask and dns server info from either one of 2 OES dhcp servers that assign addresses in different scopes in the same subnet. the internal dns server is a different OES dns server the default gateway is not assigned by the OES server but is statically put in at the client (only for those who need to get to the Internet for their job) flat network topology What can I do to get to the bottom of this? It only happens to a few of the client machines and typically the same ones. It started happening when we made a change to one of the DHCP scopes in iManager. Strangly this problem only happens to clients that get an IP address from the scope that we didn't make any changes to.

  Read the article

• Windows Vista - Can Boot into Safe Mode Command Prompt, Cannot Access Flash Drive

  - by Adam

  Hey there, Got a laptop dropped into my lap. Has Vista installed. Normal boot never gets past the login screen. Safe mode will get past, but just barely. I can try and start the task manager at that point, but it never opens. Only reliable way to do anything I've got is the safe mode command prompt... Boots up and logs in fine. I can't see anything noticably wrong via regedit, but it's been a long time since I've had to fix up a Windows box... not sure that I would. Problem I'm having, is that I want to run ComboFix/etc, but have no way to get them on there... When I pop a flash drive in, it seems to mount it (flash drive flickers as normal) but it never seems to be mounted... I cannot access it through any drive letter on the command line. I managed to start the device manager (devmgmt.msc) and the flash drive was recognized and listed... Any ideas on how to get this thing going again? (Short of a reinstall.) (It has no CD drive, either, so burning files to CD would not be easy...) Thanks! Adam

  Read the article

• Software Diagnostics Tool recommendations for Debugging a Windows 8 freeze

  - by Stuart

  I've had my HP Pavillion dv6 laptop since last November - and it has had 8GB RAM and a 256GB Crucial M4 SSD installed since the start. I use it for software development and it's had a Windows 8 RTM installation since early September. Yesterday I had to give a presentation at a customer site - so used Powerpoint for the first time since installing Win8... since that point my machine has 'frozen' every 2 hours or so after startup. There doesn't seem to be any easy to see reason behind the freeze - the system just freezes, even if I have left it idle with just a desktop there. My immediate suspicion is that the SSD is the mostly likely cause of the problem. I've looked at some of the questions on here - e.g. How do I troubleshoot hardware issues related to a computer freeze/crash? - but don't really want to start taking my laptop apart. Another suspicion is that this might be related to the WiFi adapter (Broadcom 802.11n) since I have noticed that this doesn't seem to play perfectly with things like Hyper-V in Win8. Can anyone recommend any software diagnostic tools that I can run in order to evaluate the health of the SSD or of other parts of the system? Thanks Stuart P.S. I doubt Powerpoint is the cause of this, but I may use it as an excuse never to use it again... More realistically perhaps something got damaged during travel to the customer site?

  Read the article

• how to reinstall ubuntu 12.04 after dual boot installation fails with windows 7

  - by Rini

  I have installed Ubuntu 12.04 on my preinstalled windows 7 Sony vaio s series laptop following instructions here: http://www.linuxbsdos.com/2012/05/17/how-to-dual-boot-ubuntu-12-04-and-windows-7/ Everything went well and I am able to boot in to windows after complete installation of Ubuntu. Now following instructions on web I tried to add Ubuntu to my BIOS using Easy BCD (but forget to add windows 7 entry). As a result, I loose windows 7 OS and can't boot in to either OS then I successfully repaired windows 7 using recovery CD. Now my problem is that I can't reinstall Ubuntu 12.04 using Live CD it halts every time before disk partition step giving error. There is only one partition which corresponds to windows 7 but I don't know whether the Ubuntu is still there or probably corrupted. So, how to repair it or again install ubuntu ? Please suggest what I should do now? Thanks in advance. R Shukla

  Read the article

• network policy + WPA enterprise (tkip) Windows 2008 R2

  - by Aceth

  hi I've attempted the following guide and in a bit of a pickle. http://techblog.mirabito.net.au/?p=87 My main goal is to have a username / password based wireless authentication with active directory integration. I keep getting the error Network Policy Server denied access to a user. Contact the Network Policy Server administrator for more information. User: Security ID: domain\rhysbeta Account Name: rhysbeta Account Domain: domain Fully Qualified Account Name: domain\rhysbeta Client Machine: Security ID: NULL SID Account Name: - Fully Qualified Account Name: - OS-Version: - Called Station Identifier: 00-12-BF-00-71-3C:wirelessname Calling Station Identifier: 00-23-76-5D-1E-31 NAS: NAS IPv4 Address: 0.0.0.0 NAS IPv6 Address: - NAS Identifier: - NAS Port-Type: Wireless - IEEE 802.11 NAS Port: 2 RADIUS Client: Client Friendly Name: Belkin54g Client IP Address: x.x.x.10 Authentication Details: Connection Request Policy Name: Secure Wireless Connections Network Policy Name: Secure Wireless Connections Authentication Provider: Windows Authentication Server: srvr.example.com Authentication Type: EAP EAP Type: - Account Session Identifier: - Logging Results: Accounting information was written to the local log file. Reason Code: 22 Reason: The client could not be authenticated because the Extensible Authentication Protocol (EAP) Type cannot be processed by the server. ` I would love to have it so that non domain devices

  Read the article

• Windows PE network setup

  - by microchasm

  I'm walking through the following step-by-step guide for deploying Windows 7 via AIK: http://technet.microsoft.com/en-us/library/dd349348%28WS.10%29.aspx On step 4 (Capturing the Installation onto a Network Share), I run into a bit of a snag: attempting to connect to a network drive repeatedly fails. I'm using/deploying Dell Optiplex 380 64 bit machines, and the network cards seem to be really wonky. On the machine that I'm using to run AIK etc, the network driver wasn't found automatically. I had to manually go in and install the driver (which was found on the OEM installation media). I've since copied this to the USB key that I'm using for the Autounattend.xml so its handy. I think that because of this, the PE environment doesn't or can't instantiate the network device. Is there a way to install/configure the network device through the command prompt in PE? If not, I read about adding in the answer file path(s) to drivers, but if I did it this way, would I have to start the process all over again (i.e. create new Autounattend.xml with the PnPcustomizations path included, re-run the installation on the reference machine, install all the applications, re-make the PE iso, reboot into new PE iso)? Any shortcuts, direction, or advice would be appreciated. Thanks!

  Read the article

• Windows 2008 64bit: applications and explorer always hang

  - by Phil Farthing

  I setup a couple of Window 2008 64bit systems about 5 months ago. Initially all seemed well. Now however, for no apparent reason, things are dog slow, apps hang, explorer hangs, just clicking on something can cause a CPU spike of 100%, and often it's explorer that is eating it up. As I have two on identical hardware, and they experience the same problem, it doesn't seem related to addon software. The only thing these have in common is Kaspersky and I've tried disabling/uninstalling to no avail. There are no useful error messages in the event logs. Actually, the system never even reports app hangs. Sometimes, it similar to what I've seen on Windows 7 systems where the screen goes milky and asks if I want to trouble shoot, that's only when get impatient and click happy. The really odd thing, is that it will NOT do this for a few minutes at a time, and then starts up again. Like I will click on the start menu and browse for the Admin Tools, the start menu will hang at some point and I'll have to wait about a minute, then it's OK. The next time I do this, a few seconds later, it's fine. Every click seems to hang the first time around, then be ok the second time if I do the exact same thing. If anyone has any suggestions, please PLEASE let me know! thanks =)

  Read the article

• windows xp blue screen dumping physical memory

  - by dotnet-practitioner

  I get following blue screen after running my laptop for an hour... A problem has been detected and windows has been shut down to prevent damange to your computer. If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to be sure you have adequate disk space. If a driver is identified in the stop message, disable the driver or check with the manufacturer for driver updates. Try changing video adapters. Check with your hardware vendor for any BIOS updates. Disable BIOS memory options such as cashing or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select advanced startup options, and the select safe mode. Technical Information: * STOP 0x0000008E (0xc0000005, 0x805B03F5, 0xF703DC7C, 0x00000000) Beginning dump of physical memory Physical memory dump complete. Contact you system administrator or technical support group for further assistance. so.... if this is a faulty memory.... from where I could buy RAM for following laptop.... TOSHIBA SATELLITE A45-S250 My local Frys store does not carry memory for this laptop.

  Read the article

• Windows Server 2008 (Web Server) Replication

  - by justjoshingyou

  We have a load balanced environment with Windows Server 2008. What are some best practices to setting up replication across the web servers? Do I only want to replicate the web folders? How about replicating IIS changes - or do I need to make IIS changes on every server? I've never, ever set up replication, but I have worked with a web farm that used it before. Basically, I only know the basics about how it works, and am looking for any advice, guides, warnings, etc on setting this up. If you'd like to offer any advice, I'll let you know how our environment is for now. We have 1 prod server up and the second is nearly ready to go. We are using a cloud system and all machines are VM's. I am in the process of setting up the domain controller now (as I need to have one for DFS). Any ideas on the best way to go about setting up replication? Should we just stick the prod server in from the start or set up using a test VM and our second server and then switch it up later? I do not want to risk overwriting our prod server. Thanks!

  Read the article

• Compressing and copying large files on Windows Server?

  - by Aaron

  I've been having a hard time copying large database backups from the database server to a test box at another site. I'm open to any ideas that would help me get this database moved without having to resort to a USB hard drive and the mail. The database server is running Windows Server 2003 R2 Enterprise, 16 GB of RAM and two quad-core 3.0 GHz Xeon X5450s. Files are SQL Server 2005 backup files between 100 GB and 250 GB. The pipe is not the fastest and SQL Server backup files typically compress down to 10-40% of the original, so it made sense to me to compress the files first. I've tried a number of methods, including: gzip 1.2.4 (UnxUtils) and 1.3.12 (GnuWin) bzip2 1.0.1 (UnxUtils) and 1.0.5 (Cygwin) WinRAR 3.90 7-Zip 4.65 (7za.exe) I've attempted to use WinRAR and 7-Zip options for splitting into multiple segments. 7za.exe has worked well for me for database backups on another server, which has ~50 GB backups. I've also tried splitting the .BAK file first with various utilities and compressing the resulting segments. No joy with that approach either- no matter the tool I've tried, it ends up butting against the size of the file. Especially frustrating is that I've transferred files of similar size on Unix boxes without problems using rsync+ssh. Installing an SSH server is not an option for the situation I'm in, unfortunately. For example, this is how 7-Zip dies: H:\dbatmp>7za.exe a -t7z -v250m -mx3 h:\dbatmp\zip\db-20100419_1228.7z h:\dbatmp\db-20100419_1228.bak 7-Zip (A) 4.65 Copyright (c) 1999-2009 Igor Pavlov 2009-02-03 Scanning Creating archive h:\dbatmp\zip\db-20100419_1228.7z Compressing db-20100419_1228.bak System error: Unspecified error

  Read the article

• Black Screen on Logon (windows 7 home premium)

  - by Blacknight334

  i have been having some trouble with a dell Xps 15 laptop that i recently purchased. it is under a month old, and a problem has occurred, upon logging on just after start up, the computer will just sit on a black log on screen (with the mouse still visible and active) for a few minutes. it is extremely annoying, especially when im in a rush. the laptop is under a month old. So far, i have tried to update the drivers, all windows update, and still, nothing. also, it doesnt seem to do it when i log into safe mode, or if it does, it will do it for less than 10 seconds, then load the desktop (in normal boot, it usually takes a few minutes). i have also run a number of the inbuilt diagnostics, but found no errors. i want to avoid having to do a system restore for as long as i can. does anyone know anything that can help? (the laptop is running a 500gb SSD, 2gb Nvidia 640m, 8gb ram, 3rd gen i7 quad core with 8 threads) thanks.

  Read the article

• Windows 7 boot issues

  - by Michael

  Ok, I tried to install linux and dual boot my laptop with 7 ultimate. I messed up. When I tried to boot to 7 it said no. Something along the lines of device not found. So I being young and stupid I uninstalled linux which I could boot into, and I still could not boot to windows. Next step was to run the startup fixes from the boot cd. Swing and a miss, I also ran the fixmbr and fixboot. Which brings us up to my current place. I installed 7 again on my blank partition in hopes I could access my other partion. No dice. So my question to yall is how can I fix my original filesystem or at least get to the stuff on it. In the new 7 install the old partion does not even have a drive letter. That is my sad story any help would be apreciated.

  Read the article

< Previous Page | 363 364 365 366 367 368 369 370 371 372 373 374  | Next Page >