Search Results

Search found 22900 results on 916 pages for 'pascal case'.

Page 368/916 | < Previous Page | 364 365 366 367 368 369 370 371 372 373 374 375  | Next Page >

• unknown codec 0x0064 (G726 ADPCM)

  - by Colin Pickard

  I've got a number of audio recordings which I can't play back. It appears to be a case of a missing codec, but I can't locate the codec in question. VLC will not play the files. ffmpeg gives the error Unsupported codec (id=0) for input stream 0. This is the output from MediaInfo. General CompleteName : Format : Wave FileSize/String : 164 KiB Duration/String : 1mn 24s OverallBitRate/String : 16.0 Kbps Audio Format : ADPCM CodecID : 64 CodecID/Info : G.726 CodecID/Hint : APICOM Duration/String : 1mn 24s BitRate_Mode/String : Constant BitRate/String : 16.0 Kbps Channel(s)/String : 1 channel SamplingRate/String : 8 000 Hz BitDepth/String : 2 bits StreamSize/String : 164 KiB (100%) Can anyone help?

  Read the article

• How to open a VirtualBox (.VDI) Virtual Machine

  - by [email protected]

   How to open a .VDI Virtual MachineSometimes someone share with us one Virtual machine with extension .VDI, after that we can wonder how and what with?Well the answer is... It is a VirtualBox - Virtual Machine. If you have not downloaded it you can do this easily, just follow this post.http://listeningoracle.blogspot.com/2010/04/que-es-virtualbox.htmlorhttp://oracleoforacle.wordpress.com/2010/04/14/ques-es-virtualbox/Ok, Now with VirtualBox Installed open it and proceed with the following:1. Open the Virtual File Manager. 2. Click on Actions ? Add and select the .VDI fileClick "Ok"3.  A new Virtual machine will be displayed, (in this Case, an OEL5 32GB Virtual Machine is available.)4. This step is important. Once you have open the settings, under General option click the advanced settings. Here you must change the default directory to save your Snapshots; my recommendation set it to the same directory where the .Vdi file is. Otherwise you can have the same Virtual Machine and its snapshots in different paths.5. Now Click on System, and proceed to assign the correct memory and define the processors for the Virtual machine. Note: Enable  "Enable IO APIC" if you are planning to assign more than one CPU to the Virtual Machine.6. Associated the storage disk to the Virtual machineThe disk must be selected as IDE Primary Master. 7. Well you can verify the other options, but with these changes you will be able to start the VM. Note: Sometime the VM owner may share some instructions, if so follow his instructions.8. Click Ok and Push Start Button, and enjoy your Virtual Machine

  Read the article

• SQL SERVER – Fun Post – Connecting Same SQL Server using Different Methods

  - by pinaldave

  Yesterday I had faced error when I was connecting SQL Server using 127.0.0.1. I had immediately checked if SQL Server is working perfectly by connecting to it by specifiing my local box computer. While I was doing this suddenly I realize that it is indeed interesting to know how many different way we can connect to SQL Server which is installed in the local box. I created list of 5 different way but I am sure there are many more ways and I would like to document there here. Here is my setup. I am attempting to connect to the default instance of SQL Server from the same system where it is installed. Method 1: Connecting using local host IP 127.0.0.1 Method 2: Connecting using just a single dot (.) Method 3: Connecting using (local) Method 4: Connecting using localhost Method 5: Connecting using computer name – in my case it is BIG Here are my two questions for you? (Scroll below the image) 1) Which is your favorite method? 2) What are other methods you are familiar with to connect to local host? Reference: Pinal Dave (http://blog.SQLAuthority.com)     Filed under: PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

  Read the article

• Interactive Reporting with BI Publisher 11G

  - by kanichiro.nishida

  One of the new features that came out with BI Publisher 11G and made me really excited about is the Interactive Viewer, which allows you to interact with the data presented in the reports and gain more insights about the data. You can have as many Table, Chart, Pivot Table, Gauge components in a single report and all of them are linked together so that you can click on any data point on the components such as Chart, Pivot Table, Gauge, and that would refresh other components in the report to reflect the selection without refreshing the whole report or page. No longer you need to navigate to another report or open other reports to see related data or drill down to the detail data. It’s all there within a single report. Well, sounds cliché but really this is a typical case of ‘seeing is believing’, so instead of reading I would love you guys to take a look so I’ve recorded the following video. Please take a look !   The above video shows you the power of the BI Publisher Interactive Viewer with a real data from San Francisco Airport. The lists shown at the top or the left are one of the new features that we’ll be introducing in coming future very soon, but everything else is there with 11.1.1.3. So why not start today ? And please share your feedback with us!

  Read the article

• zfs rename/move root filesystem into child

  - by Anton

  Similar question exists but the solution (using mv) is awful because in this case it works as "copy, then remove" rather than pure "move". So, I created a pool: zpool create tank /dev/loop0 and rsynced my data from another storage in there directly so that my data is now in /tank. zfs list NAME USED AVAIL REFER MOUNTPOINT tank 591G 2.10T 591G /tank Now I've realized that I need my data to be in a child filesystem, not in /tank filesystem directly. So how do I move or rename the existing root filesystem so that it becomes a child within the pool? Simple rename won't work: zfs rename tank tank/mydata cannot rename to 'tank/mydata': datasets must be within same pool (Btw, why does it complain the datasets are not within same pool when if fact I only have one pool?) I know there are solutions that involve copying all the data (mv, or sending the whole dataset to another device and back), but shouldn't there be a simple elegant way? Just noting that I do not care of snapshots at this stage (there are none yet to care of).

  Read the article

• Community Events and Workshops in November 2012 #ssas #tabular #powerpivot

  - by Marco Russo (SQLBI)

  I and Alberto have a busy agenda until the end of the month, but if you are based in Northern Europe there are many chance to meet one of us in the next couple of weeks! Belgium, 20 November 2012 – SQL Server Days 2012 with Marco Russo I will present two sessions in this conference, “Data Modeling for Tabular” and “Querying and Optimizing DAX” Copenhagen, 21-22 November, 2012 – SSAS Tabular Workshop with Alberto Ferrari Alberto will be the speaker for 2 days – you can still register if you want a full immersion! Copenhagen, 21 November 2012 – Free Community Event with Alberto Ferrari (hosted in Microsoft Hellerup) In the evening Alberto will present “Excel 2013 PowerPivot in Action” Munich, 27-28 November 2012 - SSAS Tabular Workshop with Alberto Ferrari The SSAS workshop will run also in Germany, this time in Munich. Also here there is still some seat still available. Munich, 27 November 2012 - Free Community Event with Alberto Ferrari (hosted in Microsoft ) In the evening Alberto will present “Excel 2013 PowerPivot in Action” Moscow, 27-28 November 2012 – TechEd Russia 2012 with Marco Russo I will speak during the keynote on November 27 and I will present two session the day after, “Developing an Analysis Services Tabular Project BI Semantic Model” and “Excel 2013 PowerPivot in Action” Stockholm, 29-30 November 2012 - SSAS Tabular Workshop with Marco Russo I will run this workshop in Stockholm – if you want to register here, hurry up! Few seats still available! Stockholm, 29 November 2012 - Free Community Event with Marco Russo In the evening I will present “Excel 2013 PowerPivot in Action” If you want to attend a SSAS Tabular Workshop online, you can also register to the Online edition of December 5-6, 2012, which is still in early bird and is scheduled with a friendly time zone for America’s countries (which could be good for Europe too, in case you don’t mind attending a workshop until midnight!).

  Read the article

• TweetMeme Button or Template Plug-In for WLW

  - by Tim Murphy

  In my search for a way to allow readers to tweet post that I put on GWB I have come across the TweetMeme plug-in for Windows Live Writer.  It automatically puts a twitter button at either the top or bottom of your post depending on how you configure it.  It comes with a warning that it does not work with blog servers that strip out script from posts which I made me afraid it was going to make it incompatible with GWB.  This turned out to be the case so I figured we would need either an upgrade to the GWB platform or writing my own WLW plug-in.  In comes the Template plug-in.  This allows you to have standardized content that you can insert with a couple of clicks via the interface below. This solved the problem (sort of).  It required that I remove the standard javascript that is defined by Twitter’s button page.  In the end I am hoping for an update to our Subtext implementation to incorporate features like Facebook, Twitter, Reddit and G+, but this should help us until that comes along. Update: It looks like this was all useless since it seems that the buttons are in GWB.  I didn’t think I saw them before.  Either it is recent or I am blind. del.icio.us Tags: Twitter,TweetMeme,GWB,WLW,Windows Live Writer,Geeks With Blogs,plug-ins Tweet

  Read the article

• DNS: forward part of a managed domain to one host, but sub domain services to another (Google Apps)

  - by Paul Zee

  I was going to post this as a comment against DNS: Forward domain to another host, but I don't seem able to do that. I'm in a similar situation. I have a DNS registered/managed by enom, except with the slight twist that the domain was originally registered with enom through a Google Apps account creation. The domain currently supports a Google Apps site/account. I now want to direct the bare primary domain and www entries to a hosting provider for the website component, but leave the Google Apps setup intact for its services such as calendar, mail etc. For now, I'm leaving the domain managed by enom. Also note that when I registered my account with the hosting provider, I gave the same domain name as the existing domain (e.g. example.com), so at their end I'm working with the same domain name in cpanel, etc. In my case, the existing enom DNS entries don't have an A record for the www.example.com, or the bare example.com domain. Instead, there are 4 x @ records with the Google Apps IP Address, 2 x TXT records with what I assume are Google Apps site verification strings/tokens, and a bunch of CNAME records for the various features of Google Apps (mail, calendar, docs, sites, etc). So, my questions: How do I point the www.example.com and example.com DNS entries at enom to my web site hosting provider, while leaving the domain managed by enom, and the Google Apps services working as they are now (with the obvious exception of Google Sites)? How do I setup the example.com mail-related DNS records (MX, etc) at the web site hosting provider, so that outbound email to [email protected] gets correctly sent to the google apps mail account, and doesn't get trapped inside the pseudo domain within the hosting providers servers?

  Read the article

• Have SSIS' differing type systems ever caused you problems?

  - by jamiet

  One thing that has always infuriated me about SSIS is the fact that every package has three different type systems; to give you an idea of what I am talking about consider the following: The SSIS dataflow's type system is made up of types called DT_*  (e.g. DT_STR, DT_I4) The SSIS variable type system is based on .Net datatypes (e.g. String, Int32) The types available for Execute SQL Task's parameters are based on something else - I don't exactly know what (e.g. VARCHAR, LONG) Speaking euphemistically ... this is not an optimum situation (were I not speaking euphemistically I would be a lot ruder) and hence I have submitted a suggestion to Connect at [SSIS] Consolidate three type systems into one requesting that it be remedied. This accompanying blog post is not however a request for votes (though that would be nice); the reason is actually subtler than that. Let me explain. I have been submitting bugs and suggestions pertaining to SSIS for years and have, so far, submitted over 200 Connect items. If that experience has taught me anything it is this - Connect items are not generally actioned because they are considered "nice to have". No, SSIS Connect items get actioned because they cause customers grief and if I am perfectly honest I must admit that, other than being a bit gnarly, SSIS' three type system architecture has never knowingly caused me any significant problems. The reason for this blog post is to ask if any reader out there has ever encountered any problems on account of SSIS' three type systems or have you, like me, never found them to be a problem? Errors or performance degredation caused by implicit type conversions would, I believe, present a strong case for getting this situation remedied in a future version of SSIS so if you HAVE encountered such problems I would encourage you to leave a comment on the Connect submission accordingly. Let me know in the comments too - I would be interested to hear others' opinions on this. @Jamiet

  Read the article

• Wacom Bamboo CTH460L issues

  - by Robert Smith

  I recently bought a Wacom Bamboo Pen & Touch CTH460L. I installed doctormo's PPA, however, the pen functionality didn't work and the touch was very glitchy (when I touched it, it immediately double clicked and began to drag elements in the screen). I tried to configure it using the wacom-utility package in the Synaptic Package Manager (version 1.21-1) but that didn't work either. Then I followed this post (#621, written by aaaalex), and after some problems trying to restart Ubuntu (graphics related problems), the pen works fine (it could be better, though) but the touch functionality doesn't work anymore. Currently I have installed xserver-xorg-input-wacom (1:0.10.11-0ubuntu7), wacom-dkms (0.8.10.2-1ubuntu1) and wacom-utility. The Wacom Utility only displays an "options" field under "Wacom BambooPT 2FG 4X5" but no other option to configure it. What is the correct way to get this tablet working on Ubuntu 10.04?. By the way, currently I can't start Ubuntu properly when the tablet is connected (in that case, Ubuntu start in low graphics mode). I need to connect it later. UPDATE: I uninstalled xserver -xorg-input-wacom, and wacom-utility because one of them prevented Ubuntu to start normally. I only re-installed wacom-dkms 0.8.10.2-1ubuntu1. The pen is working but no touch functionality. The side buttons don't work either. Thanks in advance.

  Read the article

• arp problems with transparent bridge on linux

  - by Mink

  I've been trying to secure my virtual machines on my esx server by putting them behind a transparent bridge with 2 interfaces, one in front, one at the back. My intention is to put all the firewall rules in one place (instead of on each virtual server). I've been using as bridge a blank new virtual machine based on arch linux (but I suspect it doesn't matter which brand of linux it is). What I have is 2 virtual switchs (thus two Virtual Network, VN_front and VN_back), each with 2 types of ports (switched/separated or promiscious/where the machine can see all packets). On my bridge machine, I've set up 2 virtual NIC, one on VN_front, one on VN_back, both in promisc mode. I've created a bridge br0 with both NIC in it: brctl addbr br0 brctl stp br0 off brctl addif br0 front_if brctl addif br0 back_if Then brought them up: ifconfig front_if 0.0.0.0 promisc ifconfig back_if 0.0.0.0 promisc ifconfig br0 0.0.0.0 (I use promisc mode, because I'm not sure I can do without, thinking that maybe the packets don't reach the NICs) Then I took one of my virtual server sitting on VN_front, and plugged it to VN_back instead (that's the nifty use case I'm thinking about, being able to move my servers around just by changing the VN they are plugged into, without changing anything in the configuration). Then I looked into the macs "seen" by my addressless bridge using brctl showmacs br0 and it did show my server from both sides: I get something that looks like this : port no mac addr is local? ageing timer 2 00:0c:29:e1:54:75 no 9.27 1 00:0c:29:fd:86:0c no 9.27 2 00:50:56:90:05:86 no 73.38 1 00:50:56:90:05:88 no 0.10 2 00:50:56:90:05:8b yes 0.00 << FRONT VN 1 00:50:56:90:05:8c yes 0.00 << BACK VN 2 00:50:56:90:19:18 no 13.55 2 00:50:56:90:3c:cf no 13.57 the thing is that the server that are plugged in front/back are not shown on the correct port. I suspect some horrible thing happening in the ARP-world... :-/ If I ping from a front virtual server to a back virtual server, I can only see the back machine if that back machine pings something in the front. As soon as I stop the ping from the back machine, the ping from the front machine stops getting through... I've noticed that if the back machine pings, then its port on the bridge is the correct one... I've tried to play with the arp_ switch of /proc/sys, but with no clear effect on the end result... /proc/sys/net/ipv4/ip_forward doesn't seem to be of any use when using a bridge (seems it's all taken care of by brctl) /proc/sys/net/ipv4/conf//arp_ don't seem to change much either... (tried arp_announce to 2 or 8 - like suggested elsewhere - and arp_ignore to 0 or 1 ) All the examples I've seen have a different subnet on either side like 10.0.1.0/24 and 10.0.2.0/24... In my case I want 10.0.1.0/24 on both side (just like a transparent switch - except it's a hidden fw ). Turning stp on/off doesn't seem to have any impact on my issue. It's as if the arp packets where getting through the bridge, corrupting the other side with false data... I've tried to use the -arp on each interface, br0, front, back... it breaks the thing altogether... I suspect it has something to do with both side being on the same subnet... I've thought about putting all my machine behind the fw, so as to have all the same subnet at the back... but I'm stuck with my provider's gateway standing at the front with part of my subnet (in fact 3 appliance to route the whole subnet), so I'll always have ips from the same subnet on both side, whatever I do... (I'm using fixed front IPs on my delegated subnet). I'm at a loss... -_-'' Thx for your help. (As anyone tried something like this? from within ESXi?) (It's not just a stunt, the idea is to have something like fail2ban running on some servers, sending their banned IP to the bridge/fw so that it too could ban them - saving all the other servers from that same attacker in one go, allowing for some honeypot that would trigger the fw from any kind of suitable response, and stuffs of the sort... I am aware I could use something like snort, but it addresses some completely different kind of problems, in a completely different way... )

  Read the article

• IoT end-to-end demo – Remote Monitoring and Service By Harish Doddala

  - by JuergenKress

  Historically, data was generated from predictable sources, stored in storage systems and accessed for further processing. This data was correlated, filtered and analyzed to derive insights and/or drive well constructed processes. There was little ambiguity in the kinds of data, the sources it would originate from and the routes that it would follow. Internet of Things (IoT) creates many opportunities to extract value from data that result in significant improvements across industries such as Automotive, Industrial Manufacturing, Smart Utilities, Oil and Gas, High Tech and Professional Services, etc. This demo showcases how the health of remotely deployed machinery can be monitored to illustrate how data coming from devices can be analyzed in real-time, integrated with back-end systems and visualized to initiate action as may be necessary. Use-case: Remote Service and Maintenance Critical machinery once deployed on the field, is expected to work with minimal failures, while delivering high performance and reliability. In typical remote monitoring and industrial automation scenarios, although many physical objects from machinery to equipment may already be “smart and connected,” they are typically operated in a standalone fashion and not integrated into existing business processes. IoT adds an interesting dynamic to remote monitoring in industrial automation solutions in that it allows equipment to be monitored, upgraded, maintained and serviced in ways not possible before. Read the complete article here. SOA & BPM Partner Community For regular information on Oracle SOA Suite become a member in the SOA & BPM Partner Community for registration please visit www.oracle.com/goto/emea/soa (OPN account required) If you need support with your account please contact the Oracle Partner Business Center. Blog Twitter LinkedIn Facebook Wiki Technorati Tags: IoT,Iot demo,sales,SOA Community,Oracle SOA,Oracle BPM,Community,OPN,Jürgen Kress

  Read the article

• Deploying site on Amazon Beantalk and IIS settings

  - by Idan Shechter

  I am interested in working with Amazon Elastic Beantalk to deploy my new site. A few things that I need to know and can't get an answer to: 1) How can I maintain IIS settings of all deployed and future deployed machines? 2) If I can maintain, what happens if I change the settings on one server, will it automatically set it on other servers? 3) How can I backup the data. In other servers I usually make an AMI and deploy to a new server in case of a problem?

  Read the article

• Setting up Ubuntu Server on Amazon EC2 for hosting multiple domains with wildcard subdomains

  - by Ashish Kumar

  I'm trying to set up multiple domains on my Amazon EC2 micro instance running Ubuntu Server 12.04. I installed Apache correctly and set up virtual hosts but having problems with wildcard subdomains. This is what my httpd.conf file looks like NameVirtualHost *:80 <VirtualHost *:80> UseCanonicalName Off VirtualDocumentRoot /home/username/domains/%0/html/ </VirtualHost> My DNS records (on Amazon Route 53) are: domain.tld A 1.2.3.4 *.domain.tld A 1.2.3.4 If i create a test.domain.tld directory with the html subdirectory, it works fine. But what I want to do is to redirect *.domain.tld to domain.tld in case there is no directory for the sub-domain accessed. I would also like www.domain.tld to redirect to domain.tld. The system should also work if I decide to host another website, example.com, on the server. I tried Googling a lot but without any luck. Suggestions?

  Read the article

• OS X Lion: Emptying the trash takes "forever": is using rm -r safe?

  - by EOL

  Emptying my Trash in OS X Lion (non securely) is taking about three hours (about 1.5 million files, from a Time Machine backup). I had to stop the process a few times already, because I could not move my laptop with the external harddrive the files are on. This is also a problem because the Trash emptying is restarted from the very beginning each time I empty the Trash again (i.e., files are not deleted when the Trash emptying is aborted). I read that it is faster to use rm -rf on ~/.Trash, in this case. However, is this safe? (I am afraid that does OS X Lion performs tasks behind the scenes—which would explain its slowness—that rm -r does not, which could lead to problems in the future.)

  Read the article

• Unable to connect to the Report Server

  - by pghcpa

  Win/7 Professional SQL Server 2008 R2 Express Reporting Services Configuration Manager When I launch it, shows correct Server Name, but report server instance is blank. When I press FIND I get: "Unable to connect to the Report Server " This is my development workstation, so no IIS installed. Seems to work fine on XP. SSMS works fine - no issues. I tried uninstalling SQL Server completely, rebooting, reinstalling a fresh download. Same result. I've googled every article I can find - nothing. Can anyone point me in the right direction in case you've come across this yourself? Thanks.

  Read the article

• How to Make Sure Your Company Doesn't Go Underwater If Your Programmers Are Hit by a Bus

  - by Graviton

  I have a few programmers under me, they are all doing very great and very smart obviously. Thank you very much. But the problem is that each and every one of them is responsible for one core area, which no one else on the team have foggiest idea on what it is. This means that if anyone of them is taken out, my company as a business is dead because they aren't replaceable. I'm thinking about bringing in new programmers to cover them, just in case they are hit by a bus, or resign or whatever. But I afraid that The old programmers might actively resist the idea of knowledge transfer, fearing that a backup might reduce their value. I don't have a system to facilitate technology transfer between different developers, so even if I ask them to do it, I've no assurance that they will do it properly. My question is, How to put it to the old programmers in such they would agree What are systems that you use, in order to facilitate this kind of "backup"? I can understand that you can do code review, but is there a simple way to conduct this? I think we are not ready for a full blown, check-in by check-in code review.

  Read the article

• Unused Indexes Gotcha

  - by DavidWimbush

  I'm currently looking into dropping unused indexes to reduce unnecessary overhead and I came across a very good point in the excellent SQL Server MVP Deep Dives book that I haven't seen highlighted anywhere else. I was thinking it was simply a case of dropping indexes that didn't show as being used in DMV sys.dm_db_index_usage_stats (assuming a solid representative workload had been run since the last service start). But Rob Farley points out that the DMV only shows indexes whose pages have been read or updated. An index that isn't listed in the DMV might still be useful by providing metadata to the Query Optimizer and thus streamlining query plans. For example, if you have a query like this: select  au.author_name         , count(*) as books from    books b         inner join authors au on au.author_id = b.author_id group by au.author_name If you have a unique index on authors.author_name the Query Optimizer will realise that each author_id will have a different author_name so it can produce a plan that just counts the books by author_id and then adds the author name to each row in that small table. If you delete that index the query will have to join all the books with their authors and then apply the GROUP BY - a much more expensive query. So be cautious about dropping apparently unused unique indexes.

  Read the article

• Linux command to concatenate audio files and output them to ogg

  - by hasen j

  What command-line tools do I need in order to concatenate several audio files and output them as one ogg (and/or mp3)? If you can provide the complete command to concatenate and output to ogg, that would be awesome. Edit: Input files (in my case, currently) are in wma format, but ideally it should be flexible enough to support a wide range of popular formats. Edit2: Just to clarify, I don't want to merge all wmas in a certain directory, I just want to concatenate 2 or 3 files into one. Thanks for the proposed solutions, but they all seem to require creating temporary files, if possible at all, I'd like to avoid that.

  Read the article

• Merging Two KML Files to Display Them with Different Marker Icons on Google Maps

  - by Maxim Z.

  Let's say that I have two spreadsheets with addresses. I uploaded these spreadsheets into Google Fusion Tables, geocoded the addresses, and exported the results as KML files. Now, I want to take these two KML files and merge them, while maintaining the location data and using it to map the points with Google Maps. Well, I found a way to easily merge the KML files: import both of them into a "My Maps" map with Google Maps! However, my problem is this: when I do that, all of the locations in my data have the same marker icon on the map. From past experience, I know that these markers can be somehow defined inside the KML files. Is it possible to combine these two KML files while giving one's points one marker icon and the other's points another marker icon? Just in case my question is confusing, what I mean, is giving the first set of points blue markers, for example, and the other set of points red markers, so that they can be overlayed.

  Read the article

• Cannot log on to a remote server using rdp from windows 7 machine when I am remotley connected to th

  - by Gary

  Bear withe me, here is my set up. I use my 27" iMac 3.06GHz Core 2 Duo 4GB Ram to connect to my work desktop running Windows 7. From there I can administer other remote servers. Here is the problem. Using the Remote Desktop Client on my Mac I can connect to my work machine no problem. But when I then use the work machine to open a remote desktop session with another Windows server (usually SBS 2003 but applies to all) I get the log in prompt, I enter the user name password ensure i'm connecting to the domain, but it wont log me in. The error message is the same, as though I had typed the wrong password (i know this is not the case). Does anyone have a solution? Thanks in advance. Gary

  Read the article

• Problem with SNMP and MIBs

  - by jap1968

  I am installing Zabbix to monitor via snmp some devices from a machine running Ubuntu 12.04 server. There is a problem with MIB definitions, since snmp commands do no properly translate some of the MIBs. I have already installed the "snmp-mibs-downloader" package, so the files containing the MIB descriptions are properly installed. The MIB are only translated to obtain the numeric key (the MIB files are accessible to the snmp commands), but the results returned by the snmpget command do not properly translate the key. The zabbix templates that I am using do expect the key translated (SNMPv2-MIB::sysUpTime.0) , so, the current results are not recognised and these are ignored. Test case: $ snmptranslate -On SNMPv2-MIB::sysUpTime.0 .1.3.6.1.2.1.1.3.0 $ snmpget -v 2c -c public 192.168.1.1 1.3.6.1.2.1.1.3.0 iso.3.6.1.2.1.1.3.0 = Timeticks: (2911822510) 337 days, 0:23:45.10 On another machine (running a very old Red Hat based distribution), the snmp commands perform both, the directe and reverse traslation, as expected: # snmptranslate -On SNMPv2-MIB::sysUpTime.0 .1.3.6.1.2.1.1.3.0 # snmpget -v 2c -c public 192.168.1.1 1.3.6.1.2.1.1.3.0 SNMPv2-MIB::sysUpTime.0 = Timeticks: (2911819485) 337 days, 0:23:14.85 What is the problem on my Ubuntu box? Is there something I am missing?

  Read the article

• Qmail does not forward mail to a specific domain

  - by jahufar

  Hi I have a dedicated hosting account with GoDaddy.com. I've pointed my domain's email to work with Google apps. The server has qmail running and it forwards email to all domains just fine except for MY domain (mydomain.com) - it says 550 User xxx not found in mydomain.com I believe it thinks I've hosted email on the server itself (not gmail) and it's trying to validate if [email protected] exists on my server (which is not the case since it's all handled by google apps). How do I make it forward mail to all domains? Thank you :) EDIT: I would only need it forwarding emails if the connection originates from 127.0.0.1 - which I believe is the default way it's configured. So to clarify: I just need a purely forwarded configuration so my PHP scripts have the ability to send email.

  Read the article

• Create Windows Bootloader/Boot into Windows from Ubuntu

  - by Kincaid

  I have computer that dual-boots (or tri-boots) Windows 8 Release Preview, Windows 7, and Ubuntu 12.04. Grub boots between Windows 8 and Ubuntu; for which I use primarily. Recently, I have decided I wanted to remove Ubuntu, as I hardly used it. As a stupid mistake, I deleted the Ubuntu partition before changing the bootloader to replace Grub. Whenever I know boot the machine, it gives me the "grub-rescue" prompt -- I am unable to boot into either Windows (8 nor 7), nor Ubuntu (except via USB, of course). I do not have any Windows 7/8 recovery media, so that isn't an option. Please note that after I deleted the Ubuntu partition, I put the PC into hibernate, and then turned it on. This means the C:\ [Windows 8] drive cannot be mounted. I don't know if that is bad, but it definitely doesn't make things better. I am currently booting Ubuntu via USB, in an effort to restore the Windows bootloader solutions. I have looked into using boot-repair to solve the problem using the instructions here, although after attempting to apply the changes, it gave the error: "Please install the [mbr] packages. Then try again." I don't know why I'm getting this error; is there a way to install the 'mbr packages?' I honestly don't know what exactly they are, nor how to install them. Is there any options I have not yet exhausted to be able to boot back into Windows, in the case that there is a better way? In the end, I want to set the bootloader to boot into Windows 8, but booting into either Windows 7 or 8 is fine -- I can use EasyBCD from there. Is there a simple solution to this? I've checked BIOS, and I haven't been able to find a way to boot into Windows. Any help would be greatly appreciated.

  Read the article

• Partner Spotlight

  - by rituchhibber

  FADATA   Fadata officially became a WebCenter Content Specialized partner in the Adriatic region upon the successful completion of the corresponding Oracle specialization tests. ''Being recognized by Oracle and customers will greatly help our company in maintaining a high level of implementation services related to Oracle Web Center Content, as one of strategic products we are focused on. This certification, that our team is very proud of, will certainly help our company FADATA to gain additional advantage, competitiveness, and integrity in implementing Oracle Web Center Content solutions, both on current and future projects in the region'' according to Velimir Corovic and Marjan Nikolic from Fadata. Please put link www.fadata.bg, under Fadata Please also include logo after 1st sentence FISHBOWL SOLUTIONS Google Search Appliance Connector for Oracle WebCenter Content The Google Search Appliance (GSA) provides fast search for your intranet or website. Fishbowl Solutions provides a connector for the Google Search Appliance to integrate it with the Oracle WebCenter Content Server while retaining the security benefits of Oracle WebCenter Content. For more information and real customer example click here Fairview Health Services Case Study or Webinar recording SIGNUM Signum TTE, from Turkey and a Gold member of Oracle® PartnerNetwork (OPN), recently announced it has achieved OPN Specialized status for Oracle WebCenter Portal. Signum TTE which began operations in the IT sector in 2005, is an innovative software solution house focusing on two main issues. Signum TTE presents services and solutions on Oracle Middleware products and technologies and its own product "WinDesk Service Management".

  Read the article

< Previous Page | 364 365 366 367 368 369 370 371 372 373 374 375  | Next Page >