Search Results

Search found 12834 results on 514 pages for 'small wolf'.

Page 369/514 | < Previous Page | 365 366 367 368 369 370 371 372 373 374 375 376  | Next Page >

  • Windows XP corrupts registry every several hours

    - by Ilya Kazakevich
    There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

    Read the article

  • What do you upgrade to make games load faster? [on hold]

    - by Superbest
    Let's say you have a relatively modern game like Shogun 2. The loading screens take several minutes. This bothers you and you'd like to improve it. What is actually going on when loading screens are up? I'm guessing assets are being loaded into memory from disk, and possibly being decompressed first. However, what is actually causing the slow down? The memory? Mainboard? CPU? HDD? If you had $100 to spend on upgrades and your only goal is to speed up loading screens without reducing other performance, what component of the computer does it make sense to upgrade for maximum benefit? If your answer is "it depends on the existing setup", what sort of benchmarks would you run to determine what is causing the bottleneck? What if you had $500 instead? I give the two budgets for context. I am not asking for actual recommendations about which component to buy (nor are the numbers supposed to be rigid limits), but what features are important when shopping for components with small and large budgets (a large budget could allow buying multiple components which are not so good on their own, but work particularly well together). I mention Shogun 2 as an example, but I'm asking about reducing overall loading times, across all games, not just one game. Therefore, "put it on a solid state disk" probably won't be good solution, because putting every game on your SDD will quickly fill it up.

    Read the article

  • Recommendations for colocation in the US

    - by Emil
    Hello serverfault I work for a European media company and we are currently looking for colocation in the US. I know the European market quite well unfortunately that is not the case for the US. I'm hoping for you guys to help me out a bit with a few questions, it would be much appreciated! I am looking for a data center that can deliver a high level of availability (tier 3 or better). The installation will be fairly large so capacity is important. Good internet connectivity/carrier presence. However most important is good customer support, skilled dedicated and responsive technical staff, since we won't have tech staff close by. I'm looking for a small and fast moving company that target internet businesses rather than big old enterprise hosting. What locations should we go for given that we want to reach all of the US from a single site and still maintain decent latency? (do we need east and west coast?) Where are the main internet hubs and should you try and get as close as possible? Are there any good online resources I should look at? Where do the large scale internet/media services colocate? Lastly I would be very happy to get some actual recommendations for companies to talk to P.S I'm happy to return the favor if anyone has question regarding data centers and colocation in Europe.

    Read the article

  • who has files open on a linux server

    - by Robert
    I have the fairly common task of finding who has files open on our Linux (Ubuntu ) file server in our Windows environment. We use Samba on the network and I use Putty from my workstation to establish a shell window to run bash scripts. I have been using something like this to find what files are open: (this returns a list of process ids with each open file) Robert:$ sudo lsof | grep "/srv/office/some/folder" Then, I follow up with something like this to show who owns the process: (this returns the name of the machine on the network using the IP4 protocol who owns the process) Robert:$ sudo lsof -p 27295 | grep "IPv4" Now I know the windows client who has a file open and can take action from there. As you can tell this is not difficult but time consuming. I would prefer to have a windows application I can run that would just give me what I want. So, I have been thinking about creating some process I can run on Linux that listens on a port and then returns a clean list of all open files with the IP address of the host who has the file open. Then, a small windows client application that can send the request on the port. It seems like this should be a very common need but I can not find anything like this that has been done before. Any suggestions?

    Read the article

  • RRAS Public Address Pool on Windows Server 2008

    - by Art
    I have a Windows 2008 server with two NICs running RRAS and a small public website. It also does NAT for several other PCs on my network and everything works great. I have a block of 5 public static IPs from my ISP, one of which is bound to the public NIC in the Windows 2008 server. I would like to assign one of the remainging 4 public IPs to a machine on my private network. I thought I could do this by going into RRAS, selecting NAT under IPv4 and then adding the public IP address to the address pool and specifying a reservation for the machine I would like to use that address by adding its private ip address. When I do this, the machine I reserved the public IP address for seems to loose all outside network connectivity. I can still ping other PCs on my 192.168.0.* net, but anything outside is no longer reachable. When I remove the reservation, everything seems to work. After setting the reservation and right clicking on the external public interface and selecting 'Show Mappings' I can see outbound requests from my private address with the desired associated private address, however I do not see any inbound requests. What am I doing wrong/missing?

    Read the article

  • Running multiple sites on a LAMP with secure isolation

    - by David C.
    Hi everybody, I have been administering a few LAMP servers with 2-5 sites on each of them. These are basically owned by the same user/client so there are no security issues except from attacks through vulnerable deamons or scripts. I am builing my own server and would like to start hosting multiple sites. My first concern is... ISOLATION. How can I avoid that a c99 script could deface all the virtual hosts? Also, should I prevent that c99 to be able to write/read the other sites' directories? (It is easy to "cat" a config.php from another site and then get into the mysql database) My server is a VPS with 512M burstable to 1G. Among the free hosting managers, is there any small one which works for my VPS? (which maybe is compatible with the security approach I would like to have) Currently I am not planning to host over 10 sites but I would not accept that a client/hacker could navigate into unwanted directories or, worse, run malicious scripts. FTP management would be fine. I don't want to complicate things with SSH isolation. What is the best practice in this case? Basically, what do hosting companies do to sleep well? :) Thanks very much! David

    Read the article

  • Remote Desktop *from* Windows 2008 R2 Server

    - by freefaller
    Summary: how do I create an RDC connection from a Windows 2008 server to another server? Our client will only allow us to connect to their server via a static IP address (which is fair enough), but unfortunately as we're a very small company we don't have one in the office. As a work around, we had the connection working through our old Windows 2003 server (dynamic-cloud from 1and1). .. however we have just rebuilt the server to run under Windows 2008 R2 (don't ask, but it was necessary), and now I simply cannot get the connection working. I have added an "Outbound Rule" to Windows Firewall with Advanced Security (TCP, All local ports, 3389 remote port - I have also tried the other way around). I have added a packet filter IP security rule with the same details. The 1and1 firewall rules (through their online control panel) allows for 3389 TCP and UDP. But it is simply not connecting (yes, the server is definitely on and able to accept connections) with the general error of... Remote Desktop can’t connect to the remote computer for one of these reasons: 1) Remote access to the server is not enabled 2) The remote computer is turned off 3) The remote computer is not available on the network Is there anything obvious I've missed - or something I can use to find out where the request is being blocked? The new server is using the exact same IP address as before, so I don't believe that would be an issue. Unless it's trying to use an IPv6 address rather than the old IPv4 address that it was before? I apologise that I am not a network person by trade, but I know more than anybody else in my office!!

    Read the article

  • Macs don't connect to wifi access point but PCs will

    - by Josh
    So, as a side project I'm going to try and figure out why the wifi APs in my building exhibit the following behavior: - They typically allow all types of computers to connect without issues - Sometimes Apples can't get an IP address but will still connect to the AP's signal - Less often, PCs can't connect to the wifi (same as above - yes signal, no IP addy) - Don't let Raiders fans on no matter the time of day! My first thought was that the DHCP leases were all taken up when the Apples would try to connect, and it was just their unlucky timing, but I would then try to log on with a PC that had a new, unleased MAC address and it would work... Could this be something to do with interoperability between an apple wifi card, and the APs? Different parts of the DHCP lease being taken up first? The fact that the Seattle Mariners might actually be good this year?? If this hasn't used up everyone's patience (with my crappy sports jokes), something else I could use some help with: - We don't have the model or type of AP - This is because there is no documentation available for them, and they literally look like small white boxes with no writing on them. Also, the company that installed them is out of business, so the situation might be that no docs will ever be on the way. -- Do you guys have any ideas on how to figure out what we have? Thanks as always for all the help, and I'm looking forward to the day when I know enough to start contributing back to the site, Josh

    Read the article

  • Using IIS7 as a reverse proxy

    - by Eric Petroelje
    I'm setting up a server at home to host a few small websites. One of them is .NET based and needs IIS, the others are PHP based and need Apache. So, I have both IIS 7 and Apache 2.2.x installed on my server with IIS on port 80 and Apache running on port 8080. I would like to set up IIS to work as a reverse proxy, forwarding the requests for the Apache sites to port 8080 and serving the requests for the .NET site itself based on the host headers. Like this: www.mydotnetsite.com/* -> IIS -> serve from IIS www.myapachesite.com/* -> IIS -> forward to apache on port 8080 www.myothersite.com/* -> IIS -> forward to apache on port 8080 I did a bit of googling and it seemed like the Application Request Routing feature would do what I needed, but I can't seem to get it to work the way I want it to. I can get it to forward ALL traffic to the Apache server and I can get it to forward traffic with a specific URL pattern to the Apache server, but I can't seem to get it to forward based on the host headers (e.g. "forward all requests for www.apachesite.com - localhost:8080") So the question is, how would I go about configuring ARR to do this? Or do I need a different tool? I'm also open to using Apache as the reverse proxy and forwarding the .NET site requests to IIS instead if that's easier (running Apache on port 80 and IIS on 8080).

    Read the article

  • Transfering call asterisk to different context

    - by Necronet
    I have a Small and basic PBX, and with two contexts wich basicly are sales and supervisor both have different roles and privileges. I notice that it is possible to transfer call from the same context but it have been imposible to transfer anything to another context. Any insight, i am kinda a rookie on asterisk but currently there is no one else in charge... Thanks Edit This is the extension.conf [supervisor] include => from-internal exten => _40XX,1,Answer exten => _40XX,n,Set(calltime=${STRFTIME(${EPOCH},,%C%y%m%d.%H.%M.%S)}) exten => _40XX,n,Set(CALLEDNUMBER=${EXTEN}) exten => _40XX,n,MixMonitor(/tmp/Para_${CALLEDNUMBER}-${calltime}-De_${CALLERID(num)}.wav) exten => _40XX,n,Dial(SIP/${EXTEN},40,TtRr) exten => _40XX,n,Hangup [sales] include => out-trunksip exten => _41XX,1,Answer exten => _41XX,n,Set(calltime=${STRFTIME(${EPOCH},,%C%y%m%d.%H.%M.%S)}) exten => _41XX,n,Set(CALLEDNUMBER=${EXTEN}) exten => _41XX,n,MixMonitor(/tmp/Para_${CALLEDNUMBER}-${calltime}-De_${CALLERID(num)}.wav) exten => _41XX,n,Dial(SIP/${EXTEN},40,TtRr) exten => _41XX,n,Hangup and the sip.conf looks like this: [supervisor] username=sales secret=ASUPERSECRETPASSWORD type=peer ..... context=supervisor mailbox=supervisor [sales] username=sales secret=ASUPERSECRETPASSWORD type=peer ..... context=sales mailbox=sales What do you suggest in order to get the supervisor with the same privileges that he already has and the sales been able to transfer calls to him

    Read the article

  • Is encryption really needed for having network security? [closed]

    - by Cawas
    I welcome better key-wording here, both on tags and title. I'm trying to conceive a free, open and secure network environment that would work anywhere, from big enterprises to small home networks of just 1 machine. I think since wireless Access Points are the most, if not only, true weak point of a Local Area Network (let's not consider every other security aspect of having internet) there would be basically two points to consider here: Having an open AP for anyone to use the internet through Leaving the whole LAN also open for guests to be able to easily read (only) files on it, and even a place to drop files on Considering these two aspects, once everything is done properly... What's the most secure option between having that, or having just an encrypted password-protected wifi? Of course "both" would seem "more secure". But it shouldn't actually be anything substantial. I've always had the feeling using any kind of the so called "wireless security" methods is actually a bad design. I'm talking mostly about encrypting and pass-phrasing (which are actually two different concepts), since I won't even consider hiding SSID and mac filtering. I understand it's a natural way of thinking. With cable networking nobody can access the network unless they have access to the physical cable, so you're "secure" in the physical way. In a way, encrypting is for wireless what building walls is for the cables. And giving pass-phrases would be adding a door with a key. So, what do you think?

    Read the article

  • BackupExec 12 + RALUS - VERY slow backups

    - by LVDave
    We use Backup Exec 12 and the Remote Agent for Linux/Unix Servers (RALUS) to backup a large RHEL5 system. For various reasons we need to do a daily working set job. These working-set jobs run abysmally slow. The link between the target machine and the BE server is gigabit, and any other type of job runs 1-3GB/min. These working-set jobs start out at perhaps 40MB/min and over the course of the backup job slowly drops down so low that the BE job rate display in the "current jobs" goes blank.. Since we usually are only doing changed-files for one day, the job is usually small and finishes overnight and we don't worry abotu the slowness, but we had some issues with the backup server, and missed about 6 days of fairly heavy work on the Linux box, so this working-set job will be a doozy.. We have support with Symantec, and I've pestered them a lot about this, they've had me run RALUS in debug mode, sent them that log and a VXgather from the BE host and they had no fix/workaround.. To give an idea, I have the mentioned working-set job running for the last 3 1/2 hours and it's backed up just under 10MEGAbytes.... I'm posting this here to see if anybody in the "real world" has seen this/and/or has any ideas what might be causing these abysmally slow jobs, since Symantec seems to be clueless...

    Read the article

  • Internet Radio Station for University

    - by ryan
    I am trying to help my University Student Radio station rethink the setup of the way they stream music, but I have some questions regarding the use of Ubuntu to stream music. Currently, the radio station uses two windows machines: one of which is used to stream the radio station and serve the website, and the other is used by rotating djs to select songs and create playlists. The computer used by djs feeds mono into the sound card of the server and the server streams the feed online. -Ideally I would like to maintain a two-computer setup: One computer as server, and another that is used to select and play music by rotating djs. -I would like to use Ubuntu for the server. -I would like to use Windows for the other machine. -The server should be able to stream song information. First, is there a way to somehow get the song information from an analog feed? Second, what is the best streaming server for radio? I have encountered shoutcast, icecast, and darwin, but I don't know where to begin in attempting to gauge them. Finally, if anyone has any tips or pointers about small internet radio station management/ setup they would be appreciated as this is my first radio station, and I am eager to hear of past experiences.

    Read the article

  • Using our own certificate authority for business email encryption

    - by LumenAlbum
    I've read the available similar questions on serverfault but I haven't quite found a definite answer to the security aspect of it - hence here's my question: I'm administrator of an office working with tax data and we want to start using certificate-based eMail encryption with our clients. Considering the prices for issued certificates by VeriSign & Co I was wondering if we couldn't issue the necessary certificates with a certificate authority of our own. I realize that they do not offer the trust hierarchy that commercial certificates do but I don't see why we would need that. Most of our clients have small businesses and only 20% of them even exchange data with us via email. So if we were to issue certificates for those 20% and our employees, that would enable us to use encrypted emails. Of course they would have to trust our certificate authority and thus once receive our public root certificate. But if we would hand them out to them (or install it) personally, they'd know that it really is our certificate. Is thery a huge security risk that I am missing here? As long as nobody has access to our certificate authority server nobody should be able to interfere with security, right? And the client certificates would be generated and handed out by us, as well... Please advise me if I am making an error in judgement here and thank you in advance.

    Read the article

  • Using UDF on a USB flash drive

    - by CesarB
    After failing to copy a file bigger than 4G to my 8G USB flash drive, I formatted it as ext3. While this is working fine for me so far, it will cause problems if I want to use it to copy files to someone which does not use Linux. I am thinking of formatting it as UDF instead, which I hope would allow it to be read (and possibly even written) on the three most popular operating systems (Windows, MacOS, and Linux), without having to install any extra drivers. However, from what I found on the web already, there seem to be several small gotchas related to which parameters are used to create the filesystem, which can reduce the compability (but most of the pages I found are about optical media, not USB flash drives). I would like to know: Which utility should I use to create the filesystem? (So far I have found mkudffs and genisoimage, and mkudffs seems the best option.) Which parameters should I use with the chosen utility for maximum compability? How compatible with the most common versions of these three operating systems UDF actually is? Is using UDF actually the best idea? Is there another filesystem which would have better compatibility, with no problematic restrictions like the FAT32 4G file size limit, and without having to install special drivers in every single computer which touches it?

    Read the article

  • Silent install FirePro v4900 Driver on Windows Embedded 7 Standard

    - by Birgit_B
    I'm trying to install the Drivers for a FirePro v4900 on a Windows Embedded 7 Standard 64bit OS. I want the system to be as small as possible, so i would rather not install the whole catalyst control center, but only the necessary drivers. Because the installation should be accomplished absolutely unattended, the installation process of the FirePro-Driver should also be done without any user interaction. I see two possible solutions for the Problem: Install only the Drivers: Is it possible to solely install the necessary drivers? How would i achieve that? This solution would be the preferred one, because of the smaller footprint. Silent custom install the provided "FirePro_8.911.3.3_VistaWin7_X32X64_135673.exe" (found at ATI FirePro™ Driver). Is there a way, to do that? Thank you in advance for your support! Update: I managed to accomplish a silent installation. I extracted the contents of the above mention installer-file and ran \$_OUTDIR\Bin64\Setup.exe -Install. (There are some other Parameters, just run Setup.exe /?). But i couldn't achieve to just install the drivers without the Cataclyst Control Center, and it seams the Control Center has some unfulfilled dependencies and so it crashes...

    Read the article

  • a disk read error occurred

    - by kellogs
    Hi, ¨a disk read error occurred¨ appears on screen after choosing to boot into Windows XP from GRUB. [root@localhost linux]# fdisk -lu Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x48424841 Device Boot Start End Blocks Id System /dev/sda1 63 204214271 102107104+ 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 204214272 255606783 25696256 af HFS / HFS+ Partition 2 does not end on cylinder boundary. /dev/sda3 255606784 276488191 10440704 c W95 FAT32 (LBA) Partition 3 does not end on cylinder boundary. /dev/sda4 276490179 312576704 18043263 5 Extended /dev/sda5 * 276490240 286709759 5109760 83 Linux /dev/sda6 286712118 310488254 11888068+ b W95 FAT32 /dev/sda7 310488318 312576704 1044193+ 82 Linux swap / Solaris sda is a 160GB hard disk with quite a few partitions and 3 OSes installed. I am able to boot into Linux and Mac OS fine, but not into Windows anymore. The Windows system is located on /dev/sda1. I can not recall how exactly have I used testdisk but it once said that ¨The harddisk /dev/sda (160GB / 149 GB) seems too small! (< 172GB / 157GB)¨ or something simillar. So far I have tried to ¨fixboot¨ and ¨chkdsk¨ from a recovery console on the affected windows partition (/dev/sda1), the plug off power cord for 15 seconds trick, reinstalling GRUB, repairing the MFT and boot sector of the affected partition via testdisk, what next please ? Thank you!

    Read the article

  • Is there an IE8 setting or policy to make it work like IE7 with respect to persistent connections?

    - by Stephen Pace
    I am working with a commercial application running on XP using IIS 5.1. Periodically the application is returning an IIS error "There are too many people accessing the Web site at this time." This is caused by Microsoft artificially limiting the number of connections (10) under IIS 5.1 under Windows XP, but in this case, there is really only one user (albeit a few tabs open at a time). Microsoft suggests you can reduce the problem by turning off HTTP Keep-Alives for that particular web site: http://support.microsoft.com/kb/262635 If you use IIS 5.0 on Windows 2000 Professional or IIS 5.1 on Microsoft Windows XP Professional, disable HTTP keep-alives in the properties of the Web site. When you do this, a limit of 10 concurrent connections still exists, but IIS does not maintain connections for inactive users. I may do that; however, I'm worried about performance degradation. However, I also notice that IE8 appears to handle this differently than IE7. By default, IE6 and IE7 use 2 persistent connections while IE8 uses 6. Perhaps in this case IE8 itself is generating multiple connections in an attempt to be faster, but those additional connections are overwhelming the artificially limited IIS 5.1 on XP? Assuming that is the case, is there an Internet Explorer option, registry setting, or policy I can set to force IE8 to behave like IE7 with respect to persistent connections? I would not set this for all users, but for the small number of users that used this application, it might solve their intermittent problem until the application can be rehosted on Windows Server 2008. Thanks.

    Read the article

  • MS licensing of multiple RDP sessions for non-MS products in Windows XP Pro

    - by vgv8
    Question 1) and 2) were moved into separate thread Which Windows remote connections bypass LSA? and what r definitions of login vs. logon session? 3) Do I understand correctly that multiple remote RDP sessions are supported by Windows XP but require additional (or modified) licensing? Which one? Or it is always illegal to run multiple RDP sessions on Windows XP? even through non-MS commercial software? ---------- Update1: I already understood my error - the main questions were about definitions (important to find the common language with others) and the licensing questions were collateral - but it was already answered. I shall try to separate these questions leaving here the questions about RDp licensing and migrating other questions into separate thread ---------- Update2: Trying to "work around" licensing terms is pointless and wasteful of time I never try "working around" and I never ask anything like this, I am not specialist in licensing. My clients/employers provide me with tools and licensing support. They have corporate lawyers, planning/accounting/purchase departments for these issues. The questions that I ask is the matter of scalability and efficiency (saving my and others time) in my developing work. For ex., Just because I need autentication against Windows AD it is time-saving to use ADAM instead of deploying full-fledged AD with DC + servers + whatever else? Nobody is forcing you to use Windows XP I shall not rush into re-installing all my operating systems on all my development machines (at home, at client premises) just because a few guys have a lot of fun downvoting development-related questions in serverfault.com. If I do so, I make a joker from me in the eyes of my clolleagues et al Update: I unmarked this question as answered since it had not even adressed the question, at least mine. Should I understand that Terminal Server PRO, allowing Windows® XP and Windows® Small Business Server 2003 to host multiple remote desktop sessions, is illegal? Related: My answer to question Has windows XP support multiple remote login session (RDP) at a time?

    Read the article

  • Is it possible/practical to install and run Linux on a USB flash drive?

    - by Graeme Donaldson
    I'm going to replace my old 2004 vintage desktop PC soon and I have an idea of what I want to do, I'm just not sure if it's possible or realistic. In the time since I built the old PC it has slowly become less used as a PC and more as a file server, so I figured I'd build a small file server which could also function as a router/DHCP/DNS/whatever box. The idea is to base it on an Atom system. I have my eye on the Intel D510MO for the moment. This supports 2 SATA disks, and I'd prefer to dedicate those to data storage. I'd like to install Ubuntu Server or maybe Debian on a 8/16GB USB flash drive. I have seen plenty of tutorials on how to perform an installation from a USB drive, but I can't seem to find any info on actually booting and running the OS from USB flash. Is this even possible? Is it practical? This box will mostly be used for: Making backups of mine and my wife's notebooks via LAN. Will use SMB or NFS for this. Digital media storage, which will be accessed by a Mede8er box with no storage of its own. I will most likely use NFS for this.

    Read the article

  • Error importing large MySQL dump file which includes binary BLOBs in Windows

    - by Daniel Magliola
    I'm trying to import a MySQL dump file, which I got from my hosting company, into my Windows dev machine, and i'm running into problems. I'm importing this from the command line, and i'm getting a very weird error: ERROR 2005 (HY000) at line 3118: Unknown MySQL server host '+?*á±dÆ-N+Æ·h^ye"p-i+ Z+-$?P+Y.8+|?+l8/l¦¦î7æ¦X¦XE.ºG[ ;-ï?éµ?º+¦¦].?+f9d릦'+ÿG?-0à¡úè?-?ù??¥'+NÑ' (11004) I'm attaching the screenshot because i'm assuming the binary data will get lost... I'm not exactly sure what the problem is, but two potential issues are the size of the file (2 Gb) which is not insanely large, but it's not trivially small either, and the other is the fact that many of these tables have JPG images in them (which is why the file is 2Gb large, for the most part). Also, the dump was taken in a Linux machine and I'm importing this into Windows, not sure if that could add to the problems (I understand it shouldn't) Now, that binary garbage is why I think the images in the file might be a problem, but i've been able to import similar dumps from the same hosting company in the past, so i'm not sure what might be the issue. Also, trying to look into this file (and line 3118 in particular) is kind of impossible given its size (i'm not really handy with Linux command line tools like grep, sed, etc). The file might be corrupted, but i'm not exactly sure how to check it. What I downloaded was a .gz file, which I "tested" with WinRar and it says it looks OK (i'm assuming gz has some kind of CRC). If you can think of a better way to test it, I'd love to try that. Any ideas what could be going on / how to get past this error? I'm not very attached to the data in particular, since I just want this as a copy for dev, so if I have to lose a few records, i'm fine with that, as long as the schema remains perfectly sound. Thanks! Daniel

    Read the article

  • How should I monitor memory usage/performance in SunOS/Solaris?

    - by exhuma
    Last week we decided to add some SunOS (uname -a = SunOS bbs-sam-belair 5.10 Generic_127128-11 i86pc i386 i86pc) machines into our running munin instance. First off, the machines are pre-configured appliances, so, I want to avoid touching the system too much without supervision of the service provider. But adding it to munin was fairly easy by writing a small socket-service (if anyone is interested, I put it up on github: https://github.com/munin-monitoring/contrib/tree/master/tools/pypmmn) Yesterday, I implemented/adapted the required plugins for our machines. And here the questions start: First, I have not found a way to determine detailed memory usage values. I get the total memory by running prtconf | grep Memory, and the free memory using vmstat. Fiddling together a munin-plugin, gives me the following graph: This is pretty much uninformative. Compare this to the default plugin for linux nodes which has a lot more detail: Most importantly, this shows me how much memory is actually used by applications. So, first question: Is it possible to get detailed memory information on SunOS with the default system tools (i.e. not using top)? Onto the next puzzle: Seeing the graphs, I noticed activity in the "Paging in/out" graphs, even though the memory graph still has unused memory: Upon further investigation, I found out that df reports that /tmp is mounted on swap. Drilling around on the web, I understood that df will display swap, but in fact, it's mounted as a tmpfs. Now I don't know if this explains the swap activity. The default munin-plugin for solaris uses kstat -p -c misc -m cpu_stat to get these values. I find it already strange that this is using the cpu_stat module. So maybe I simply misinterpret the "paging" graphs? Second question: Do the paging graphs indicate that parts of the memory are paged to disk? Or is the activity caused by file operations in /tmp?

    Read the article

  • PC powers off at random times

    - by Timo Huovinen
    Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

    Read the article

  • Why do clients on Branch Sites insist on accessing SYSVOL on the HQ DC instead of the branches' RODC?

    - by pepoluan
    I'm still scratching my head over this situation... You see, we have 3 RW DCs in the HQ, and 1 RODC on every branch sites (50+ locations). During startup, a script will pull in some files from \\example.com\SYSVOL\example.com\Common\Data But we have been experiencing bandwidth overload. A traffic analysis indicated that lots of clients in the Branch Sites were trying to access the SYSVOL located in the RW DCs. E.g.: If the RW DCs are 10.1.0.15, 10.2.0.15, and 10.3.0.15, and site 'X' has a subnet of 10.27.0.0/16 (with its RODC at 10.27.0.15), clients at site 'X' seem to insist on accessing \\10.1.0.15\SYSVOL or \\10.2.0.15\SYSVOL or \\10.3.0.15\SYSVOL; they seem to be ignoring the RODC completely. What is going on here? Where should I start investigating what went wrong? BTW, I'm already using DFS-R, and replication have been going on successfully; I can put a small 'canary' file on one of the RW DCs, and within minutes all the RODCs will have successfully replicated the 'canary' file.

    Read the article

  • NTBackup Error: C: is not a valid drive

    - by Chris
    I'm trying to use NtBackup to back up the C: Drive on a Microsoft Windows Small Business Server 2003 machine and get the following error in the log file: Backup Status Operation: Backup Active backup destination: 4mm DDS Media name: "Media created 04/02/2011 at 21:56" Error: The device reported an error on a request to read data from media. Error reported: Invalid command. There may be a hardware or media problem. Please check the system event log for relevant failures. Error: C: is not a valid drive, or you do not have access. The operation did not successfully complete. I'm using a brand new SATA Quantum Dat-72 drive with a brand new tape (tried a couple of tapes). I carry out the following: Open NTBackup Select Backup Tab Tick the box next to C: Ensure Destination is 4mm DDS Media is set to New Press Start Backup Choose Replace the data on the media and press Start Backup NTBackup tries to mount the media Error Message shows: The device reported an error on a request to read data from media. Error reported: INvalid command. There may be a hardware or media problem. Please check the system event log for relevant failures. On checking the log I find the following: Event Type: Information Event Source: NTBackup Event Category: None Event ID: 8018 Date: 04/02/2011 Time: 22:02:02 User: N/A Computer: SERVER Description: Begin Operation For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. and then; Event Type: Information Event Source: NTBackup Event Category: None Event ID: 8019 Date: 04/02/2011 Time: 22:02:59 User: N/A Computer: SERVER Description: End Operation: The operation was successfully completed. Consult the backup report for more details. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

    Read the article

< Previous Page | 365 366 367 368 369 370 371 372 373 374 375 376  | Next Page >