Search Results

Search found 61414 results on 2457 pages for 'daylight saving time'.

Page 371/2457 | < Previous Page | 367 368 369 370 371 372 373 374 375 376 377 378  | Next Page >

• Bladecenter-E Power Module fault

  - by Lihnjo

  We have problem on IBM Bladecenter-E Critical Events Power module 2 is off. DC fault. Power module 4 is off. DC fault. Warnings and System Events Insufficient chassis power to support redundancy What is the best solution for this problem? Thanks AMM Service Data Help SPAPP Capture Available 10/13/2010 17:03:47 1090347 bytes Time: 11/19/2012 11:02:31 UUID: 42E1 5D2F D7BF 41A6 A4A2 48D1 3FB7 0540 MAC Address xx:xx:xx:xx:xx:xx MM Information Name: nnnnn Contact: aaa, bbb, ccc, England Location: [email protected] IP address: 111.222.333.444 Date Time Information GMT offset: +1:00 - Central Europe Time (Western Europe, Algeria, Nigeria, Angola) Adjust for DST: Yes NTP: Enabled NTP Hostname/IP: 111.222.333.444 System Health: Critical System Status Summary One or more monitored parameters are abnormal. Critical Events Power module 2 is off. DC fault. Power module 4 is off. DC fault. Warnings and System Events Insufficient chassis power to support redundancy CHASSIS (BladeCenter-E) in CHASSIS slot: 01 TopoPath is "CHASSIS[1]". Description : BladeCenter-E Width : 1 Sub Type : BladeCenter (BC) Power Mode : 220 v KVM Owner : CHASSIS[1]/BLADE[9] MT Owner : CHASSIS[1]/MGMT_MOD[1] Component Type : CHASSIS Inventory: VPD ID: 336 (decimal) POS ID EXT: 0 (decimal) POS ID: 8 (decimal) Machine Type/Model: 86773RG Machine Serial Number: 99ZL816 Part Number: 39R8561 FRU Number: 39R8563 FRU Serial Number: YK109174W1HV Manufacturer ID: IBM Hardware Revision: 3 (decimal) Manufacture Date: 18 (wk), 07 (yr) UUID: 42E1 5D2F D7BF 41A6 A4A2 48D1 3FB7 0540 (hex) Type Code: 97 (decimal) Sub-type Code: 0 (decimal) IANA Num: 336 (decimal) Product ID: 8 (decimal) Manufacturer Sub ID: FOXC Enviroment data: -------------- Type: : POWER_USAGE Unit: : WATTS Reading: : 0xa Sensor Label: : Midplane Sensor ID: : 0x0 MGMT MOD (Advanced Management Module) in MGMT_MOD slot: 01 TopoPath is "CHASSIS[1]/MGMT_MOD[1]". Description : Advanced Management Module Name : kant Width : 1 Component Role : Primary Component Type : MGMT MOD Insert Time : 28050132 Inventory: VPD ID: 288 (decimal) POS ID EXT: 0 (decimal) POS ID: 4 (decimal) Part Number: 39Y9659 FRU Number: 39Y9661 FRU Serial Number: YK11836CE2RC Manufacturer ID: IBM Hardware Revision: 4 (decimal) Manufacture Date: 50 (wk), 06 (yr) UUID: 1D95 9937 8CA5 11DB 9499 0014 5EDF 1C98 (hex) Type Code: 81 (decimal) Sub-type Code: 1 (decimal) IANA Num: 20301 (decimal) Product ID: 65 (decimal) Manufacturer Sub ID: ASUS Firmware data: Type : AMM firmware Build ID : BPET50P File Name : CNETCMUS.PKT Release Date : 03/26/2010 Release Level : 50 Revision - Major: 80 Port info: ======================================================== Topology Path ID : 1 Label : External Phy Orientation : EXTERNAL Port Number : 1 Type : MGT Physical Meidum : Copper Number of Link Intferfaces : 1 ------------------------------------ Link Ifc ID Number : 1 Link Ifc Transport Protocol : ENET Link Ifc Addr Type : MAC Link Ifc Burned-in Addr : xx:xx:xx:xx:xx:xx Link Ifc Admin Addr : 00:00:00:00:00:00 Link Ifc Addr in use : xx:xx:xx:xx:xx:xx ---------------------------------------------------------- Configuration behaviors: Save Only Enviroment data: -------------- Type: : TEMPERATURE Unit: : DEGREES_C Reading: : 38.00 Sensor Label: : MM Ambient Sensor ID: : 0x0 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +4.81 Sensor Label: : +5V Sensor ID: : 0x1b -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +3.26 Sensor Label: : +3.3V Sensor ID: : 0x19 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +11.97 Sensor Label: : +12V Sensor ID: : 0x16 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : -4.88 Sensor Label: : -5V Sensor ID: : 0x1e -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +2.47 Sensor Label: : +2.5V Sensor ID: : 0x18 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +1.76 Sensor Label: : +1.8V Sensor ID: : 0x15 -------------- Type: : POWER_USAGE Unit: : WATTS Reading: : 0x19 Sensor Label: : kant Sensor ID: : 0x0

  Read the article

• Taking a screencast in Backtrack 4

  - by Leboff

  I'm working on a tutorial using Backtrack 4 Live USB, and I would like to take a screencast of what I'm doing (not just screenshots) So far I have tried these application with limited success: -recordmydesktop -xvidcap -wink -istanbul -vlc -vnc2flv Each time I try the resulting files are generally choppy (at best 1 frame per second) and most don't even end up with a clear view of the screen each time. If anyone has suggestions for the screencast I would greatly appreciate it. Thanks, Bryan

  Read the article

• Slow Windows Explorer on Windows 7

  - by MadBoy

  I have Laptop with i7 (4 cores), 8GB ram and SSD OCZ Vertex 3 MaxIOPS which in testing that I did just now does 400mb/s+ read/write. However the responsiveness of Windows Explorer is far from being perfect. Opening up Computer, Documents, going into folders is very slow (1-5seconds). I don't have any viruses or spyware and I have tried changing properties to optimize view for General Items. I tried disabling Search Indexer but it made search in Outlook 2010 crawl and didn't bring any other effect. Even double clicking on file takes some time to open things up (like clicking a Word document). I don't have any drives mapped, my computer is not joined to domain. I have multiple VPN connections that I connect to but they all have disabled default gateways. I tried using CC Cleaner or some Windows 7 Tweaks app to disable some things. I am power user using Visual Studio, Tortoise SVN and other developer/administration apps. Any non obvious ideas? Edit: So I've been trying to pinpoint where the issue comes from and it seems that straight after reboot Windows Explorer opens very fast, when I load 3-4 programs (Royal TS, Visual Studio, Outlook) it's noticeably slower and the more programs I have it gets worse. After I start closing programs it starts working better and if I leave 2 open it's fast again. I tried doing some research with DiskMon and other programs from sysinternals but couldn't find anything suspicious. Below are stats during normal usage with a lots of programs open: - Ram usage with a lot of programs open and no swap file (i disabled it for testing): 6.95GB - CPU usage: 15%, none of the cores takes more then 50% (I have VS 2010 open x 4) HD Tune Pro: OCZ-VERTEX3 MI Benchmark Test capacity: full Read transfer rate Transfer Rate Minimum : 363.9 MB/s Transfer Rate Maximum : 505.5 MB/s Transfer Rate Average : Access Time : Burst Rate : CPU Usage : HD Tune Pro: OCZ-VERTEX3 MI File Benchmark Drive C: Transfer rate test File Size: 500 MB Sequential read 484102 KB/s Sequential write 444714 KB/s Random read 7779 IOPS Random write 16888 IOPS Random read (queue depth = 32) 73007 IOPS Random write (queue depth = 32) 69790 IOPS HD Tune Pro: OCZ-VERTEX3 MI Random Access Test capacity: full Read test Transfer size operations / sec avg. access time max. access time avg. speed 512 bytes 3260 IOPS 0.306 ms 2.106 ms 1.592 MB/s 4 KB 4161 IOPS 0.240 ms 2.006 ms 16.256 MB/s 64 KB 2382 IOPS 0.419 ms 2.367 ms 148.934 MB/s 1 MB 449 IOPS 2.225 ms 4.197 ms 449.407 MB/s Random 809 IOPS 1.235 ms 6.551 ms 410.527 MB/s HD Tune Pro: OCZ-VERTEX3 MI Extra Tests Test capacity: full Random seek 3975 IOPS 0.252 ms 1.941 MB/s Random seek 4 KB 4245 IOPS 0.236 ms 16.583 MB/s Butterfly seek 4086 IOPS 0.245 ms 1.995 MB/s Random seek / size 64 KB 3812 IOPS 0.262 ms 58.606 MB/s Random seek / size 8 MB 120 IOPS 8.348 ms 485.737 MB/s Sequential outer 4524 IOPS 0.221 ms 282.721 MB/s Sequential middle 4429 IOPS 0.226 ms 276.818 MB/s Sequential inner 5504 IOPS 0.182 ms 344.000 MB/s Burst rate 4472 IOPS 0.224 ms 279.475 MB/s

  Read the article

• how to get CPU utilization in zabbix from Windows server?

  - by kusoksna

  I'm trying to monitor CPU utilization of windows 7 32bit PC (C2D E8400) using zabbix. I tried both "perf_counter[\Processor Information(_Total)\% Processor Time]" and "system.cpu.util[,system,avg5]". After some time status of these items reverted itself to "Unsupported". Is this problem on agent side, or at server? How to fix it? Ideally I want to see percentages load per each core. UPD: topic and description updated.

  Read the article

• Hosts file resetting on Windows 7

  - by Simon

  Recently I've noticed my hosts file resetting itself. D:\Windows\System32\drivers\etc (OS installed on D drive) First time it reset it to the default, and now for the first time its completely disappeared after installing a whole bunch of updates. I don't have any virus protection other than Microsoft's Security Essentials. What's going on???

  Read the article

• Microsoft Office 2007

  - by nardone25

  Hello everyone in serverfault. I am having a big problem at my job. I will let everyone know what I am using. I have two ibm x3690 servers with vmware esxi on both. Our product server has 8 vm on there. I have two lefthand san from HP. I have a watchgurd firewall. Our other site. I have one server over there ibm x3b90 sever. with one vm on there. I have a cisco 1700 router. and another watchgurd firewall. I have a vpn tunnel to my watchgurd firewall, to my cisco router. Site one works great. site two is having problems saving word documents and having problems printing in publisher 2007. Can someone please help?

  Read the article

• WYSIWYG editor for structured text (suitable for SVN versioning)

  - by chris_l

  I'm looking for an open source cross platform WYSIWYG editor that I can use to write documentation. I'm not looking for a web based solution - i.e. it should work without a web server, and I want to save my files directly to disk. The result could be any structured format, like Wiki markup, ReStructuredText, DocBook, or a small subset of HTML, ... But it's important, that Subversion diff can be used to see differences between the versions easily (this wouldn't work with .odt or .rtf files for example) I'm currently thinking about using Open Office, and saving the files as HTML, but is there a better solution?

  Read the article

• How to configure LAN IP Filter on Huawei E586 UMTS Modem

  - by Mose

  I need to prevent clients of an Huawei E586 UMTS to WiFi modem from downloading much data from specific servers eg. Windows update or OSX update. On the config page of the device there's an "LAN IP Filter" which seems pretty good but I can't figure out the right settings. The mask looks like this: The help pages states the following: My problem with this is, I want some wildcard for the local ip and port. In my opinion the help page can not be correct by "lan port: enter 80" because the source port is normally dynamic. I tried to set it up like stated there but as expected it doesn't work. As wildcards I tried * and "ALL" but nothing worked as it prevents me from saving settings with an "wrong value" error. Any suggestions? Thanks in advance!

  Read the article

• PCI-e v2.0 video card in a PCI-e v1.0 slot? [closed]

  - by Kevin

  Possible Duplicate: Will a PCI-E V2.0 Graphics Card work with a PCI-E V1.0 Motherboard? Will a PCI-e 2.0 card work in a PCI-e 1.0 motherboard? Currently I've got an older ASUS M2N-E motherboard, and I would like get a newer video card (GTX 280 or similar) which will last me a while after I upgrade my motherboard at some point in the future. I currently have a 6600 GT which has served me well for a long time, but it's time to upgrade.

  Read the article

• Nagios3: Conditional operators for service checks?

  - by Dave

  I'm trying to setup Nagios to monitor my various using hostgroups to define 'machine roles', against which I run services to check the machines by role. However, I'd like to use conditional operators that would enable me to run the service check against an intersection of two host groups, rather than their unions... i.e. using &&, ||, or () operators. For example, imagine I have the following servers: www-eu: Linux WWW (Apache) server, in the EU www-us: Windows WWW (IIS) server, in the US (West coast) ftp-eu: Linux FTP server, in the EU ftp-us: Windows FTP server, in the US I would want to create the following host groups: US-Servers: www-us, ftp-us EU-Servers: www-eu, ftp-eu WWW-Servers: www-us, www-eu FTP-Servers: ftp-us, ftp-eu Now say I'm interested in checking the HTTP response time for my web servers. Then let's say this particular Nagios service is running from the US (West Coast), and that I have a command called *check_http_response_time*. This command will check the responsiveness of the HTTP server, which I can provide an argument which defines the max response time before raising critical. My command might look like: check_http_response_time $HOSTNAME$ 50 Now traditionally, I can run my checks by specifying a list of host or hostgroups. define service{ use local-service hostgroup_name WWW-Servers # Servers = www-us, www-eu servicegroups WWW Checks service_description Check HTTP Response Time check_command check_http_response_time!50 } However, with the above service definition, given my Nagios service is in US West, I could reasonably expect that my EU server will return critical. Really, I want different thresholds for each region (50 for US West, 200 for EU.) I would have to permutate my service for each host and set their custom threshold, or alternatively permutate out my service groups by role & region (i.e. WWW-Servers-EU), and run my specific thresholds against those. Though the latter is better, both are much messier than I'd like... What I would love, and what this post is asking for, is a way to use hostgroups to perform an intersection using conditional logic, rather than a simple union. It might look like: define service{ use local-service hostgroup_name WWW-Servers && US-Servers servicegroups WWW Checks service_description Check HTTP Response Time check_command check_http_response_time!50 } It then would run the check only against servers that are in both WWW-Servers and US-Servers, in my example, just www-us. The benefits of such a feature would be significant for Nagios services configured for large-scale. Is this feature available? If it isn't, will it be available in the future? Is there an alternative way to accomplish this given the most recent Nagios version? Any tips/suggestions are most appreciated! Dave

  Read the article

• Wake network adapter from deep sleep mode

  - by BeatMe

  I recently buyed a new Mainboard (Asrock ALiveXFire) and got some trouble with the network adapter. After switching my Windows 7 x64 in energey saving mode and returning from it, my network adapter couldn't be found. After some googling I found out, that apparently my network adapter has been put in a deep sleep mode and didn't reactivate. Their solution was to switch the PC off, take out the RAM and the CMOS battery for some time. After that, the adapter should be powered on again, but that didn't happen for me. I waited several hours before turning my PC on again, but that didn't help. Formatting and reinstalling didn't help either. The network adapter is not found in the hardware manager and reinstalling the drivers didn't help. I have the newest BIOS installed on the mainboard. I literally don't know what to try next. I'm thinking of returning my board, but I would like to avoid the hassle.

  Read the article

• How can I prevent cron from filling up my syslog?

  - by user7321

  I have a script which needs to be executed each minute. The problem is that cron is logging to /var/log/syslog each time it executes. I end up seeing something like this repeated over and over in /var/log/syslog- Jun 25 00:56:01 myhostname /USR/SBIN/CRON[1144]: (root) CMD (php /path/to/script.php /dev/null) btw- i'm using debian My questions is- Is there any way I can tell cron not write this information to syslog every time?

  Read the article

• How to backup millions of small files?

  - by grassbl8d

  What is the best way to backup millions of small files in a very small time period? We have less than 5 hours to backup a file system which contains around 60 million files which are mostly small files. We have tried several solutions such as richcopy, 7z, rsync and all of them seems to have a hard time. We are looking for the most optimal way... We are open to putting the file in an archive first or transferring the file to another location via network or hard disk transfer thanks

  Read the article

• Block IP Address including ICMP using UFW

  - by dr jimbob

  I prefer ufw to iptables for configuring my software firewall. After reading about this vulnerability also on askubuntu, I decided to block the fixed IP of the control server: 212.7.208.65. I don't think I'm vulnerable to this particular worm (and understand the IP could easily change), but wanted to answer this particular comment about how you would configure a firewall to block it. I planned on using: # sudo ufw deny to 212.7.208.65 # sudo ufw deny from 212.7.208.65 However as a test that the rules were working, I tried pinging after I setup the rules and saw that my default ufw settings let ICMP through even from an IP address set to REJECT or DENY. # ping 212.7.208.65 PING 212.7.208.65 (212.7.208.65) 56(84) bytes of data. 64 bytes from 212.7.208.65: icmp_seq=1 ttl=52 time=79.6 ms ^C --- 212.7.208.65 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 79.630/79.630/79.630/0.000 ms Now, I'm worried that my ICMP settings are too generous (conceivably this or a future worm could setup an ICMP tunnel to bypass my firewall rules). I believe this is the relevant part of my iptables rules is given below (and even though grep doesn't show it; the rules are associated with the chains shown): # sudo iptables -L -n | grep -E '(INPUT|user-input|before-input|icmp |212.7.208.65)' Chain INPUT (policy DROP) ufw-before-input all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-before-input (1 references) ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 3 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 4 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 11 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 12 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 8 ufw-user-input all -- 0.0.0.0/0 0.0.0.0/0 Chain ufw-user-input (1 references) DROP all -- 0.0.0.0/0 212.7.208.65 DROP all -- 212.7.208.65 0.0.0.0/0 How should I go about making it so ufw blocks ICMP when I specifically attempt to block an IP address? My /etc/ufw/before.rules has in part: # ok icmp codes -A ufw-before-input -p icmp --icmp-type destination-unreachable -j ACCEPT -A ufw-before-input -p icmp --icmp-type source-quench -j ACCEPT -A ufw-before-input -p icmp --icmp-type time-exceeded -j ACCEPT -A ufw-before-input -p icmp --icmp-type parameter-problem -j ACCEPT -A ufw-before-input -p icmp --icmp-type echo-request -j ACCEPT I'm tried changing ACCEPT above to ufw-user-input: # ok icmp codes -A ufw-before-input -p icmp --icmp-type destination-unreachable -j ufw-user-input -A ufw-before-input -p icmp --icmp-type source-quench -j ufw-user-input -A ufw-before-input -p icmp --icmp-type time-exceeded -j ufw-user-input -A ufw-before-input -p icmp --icmp-type parameter-problem -j ufw-user-input -A ufw-before-input -p icmp --icmp-type echo-request -j ufw-user-input But ufw wouldn't restart after that. I'm not sure why (still troubleshooting) and also not sure if this is sensible? Will there be any negative effects (besides forcing the software firewall to force ICMP through a few more rules)?

  Read the article

• Excel Add-In not loading properly with 64-bit Excel 2013

  - by David Hyde

  I have an Excel Add-In saved to an .xla file in %appdata%\Microsoft\Addins. In the subject version of Excel it is checked on the Add-Ins list. One thing this addin does is create a drop-down menu in ThisWorkbook's Workbook_Open sub. But the menu is not created and there is no Add-Ins tab on the ribbon. No error messages. This works fine in Excel 2010 and 2007 (at least), and worked fine on the 32-bit Excel 2013 that came preinstalled on this system before I nuked it. The really maddening thing is that if I get rid of this addin and open that same .xla file, either by double-clicking or using the Open command in Excel, the menu appears as expected. I get the same behavior if I instead open the source .xls file - it all works. I've also tried saving to a .xlam file instead of .xla, but get the same bad result. Any ideas?

  Read the article

• Centos and dell PowerEdge Rxxx Series.

  - by OrenM

  hi we lately purchase few dell servers all of them from Rxxx series couple of R410 and R710 the OS we used on those servers is: CentOS 5.4 we're getting very weird error messages and we lost network connectivity couple of times (restarting the network interface was needed to fix it) the messages we're getting are: Message from syslogd@ at Wed Nov 18 12:07:08 2009 ... servername kernel: Uhhuh. NMI received for unknown reason 20. Message from syslogd@ at Wed Nov 18 12:07:08 2009 ... servername kernel: Do you have a strange power saving mode enabled? Message from syslogd@ at Wed Nov 18 12:07:08 2009 ... servername kernel: Dazed and confused, but trying to continue we have never seen those messages in the previous series of dell poweredge servers do someone here using centOS 5.4 on Rxxx series? did it happen to him too? maybe you have a suggestion about how to prevent it from happening

  Read the article

• Move "XP Mode" from Windows Virtual PC to VirtualBox?

  - by JoelFan

  I installed "XP Mode" in Windows 7 (which uses Windows Virtual PC to host XP). I have now discovered that VirtualBox, which I have installed on the same Windows 7 machine, refuses to run at the same time as Windows Virtual PC (it gives me an error about not running multiple visualization programs). Is there any way I can convert the "XP Mode" image so that it will run inside VirtualBox instead of Windows Virtual PC? That way I will be able to run XP as well as other VM's at the same time.

  Read the article

• Is there any way to do 'software raid' without losing data?I

  - by user1706582

  I say software raid because that is a pretty tentative guess at what I actually want. I have two drives, both with stuff already on them which I want to combine. If they weren't full of stuff (data, not windows installation) I would use software raid to combine them into one big drive or make them into one partition. I could probably do this with some complicated reference system but really I just want to be able to keep saving things to X: without running out of space until both drives are full. Thanks in advance.

  Read the article

• Enabled storing Bitlocker keys in Active Directory, is there a way to upload keys of drives encrypted before this?

  - by Rossaluss

  We have enabled storing of Bitlocker keys within the device object on Active Directory, however before this was implemented, we had encrypted 100+ devices using bitlocker and we've only found ways to upload the key to AD when enabling bitlocker for the first time on an install. Does anybody know of a way where we can upload all the keys for all the devices which already had their drives encrypted with Bitlocker into their respective device objects in AD? Or are we going to have to decrypt and re-encrypt all the devices on the floor? (Google seems to say this is what we're going to have to do, however we're no experts in Bitlocker, so may have missed something) When we go into Manage Bitlocker of an already encrypted device, we only get the same options of saving the key to a file, a memory stick or printing it out, no option is available to save to AD etc. Any help would be appreciated.

  Read the article

• Keyboard shortcut to minimize Remote Desktop

  - by Vaccano

  Is there a way, using the keyboard, to switch from a maximized (full screen) Remote Desktop Connection back to the main computer? I have about 4 Remote Desktop connections that I am switching between and it would be nice to not have to go to the mouse each time I want to switch. I know I can press Ctrl+Alt+Break and that normalizes the remote desktop screen. That is close, but I would like a way to just minimize it (so I don't have to normalize-switch-maximize each time I want to switch screens)

  Read the article

• Postgresql - Error: Could not create log file /var/log/postgresql/...

  - by nicefinly

  Every time I try to start postgresql, I get this error: * Starting PostgreSQL 9.2 database server * Error: Could not create log file /var/log/postgresql/postgresql-9.2-main.log To start the server, I have to sudo mkdir the postgresql folder in /var/log/ How can I start postgresql automatically every time I boot up? I already have a postgres user on the Ubuntu 12.10 system.

  Read the article

• HOSTS File Edit in Windows 7 Not Effective - Pinging URL Still Shows Original IP Address

  - by Sootah

  I've edited my HOSTS file on my Windows 7 Ultimate PC to re-route a couple of URLs so that they point to 127.0.0.1, but after saving the file (and re-opening to verify the changes were written) and pinging them they still reply with the actual IP instead of being redirected to 127.0.0.1 as they should be. At least, that's how it worked in XP, Vista, etc. I even went so far as to restart my DNS service on the machine via services.msc; but no dice. So - I would imagine that Windows 7 keeps the HOSTS file there for legacy purposes and doesn't actually use it anymore. Is there a way to make W7 pay attention to the HOSTS file? In the event that you can't do that, where would I go to edit where these URLs point to? Thanks in advance! -Sootah

  Read the article

• Ubuntu Lucid: Erratic screen behaviour after boot

  - by fgysin

  In short: about 50% of the time I have a screwed up monitor setup after reboot. About 50% it is totally correct. Now the longer version: I updated my machine from 9.04 to 10.04 (via 9.10). At first I run into some monitor problems (I have a 3-monitor setup) because of the known bug in the new xserver driver for xinerama. This messes up behaviour if the mouse goes either left or above the screen number 0, i.e. I had to make my left-most monitor screen 0. Everything worked out fine finally, I got my 3-monitor setup back with xinerama enabled to get one big desktop streched over 3 screens. Now the fun part: Every time I start up my machine only one of the 3 monitors gets a signal and is woken up: it only recognizes the left-most monitor (screen 0) and crams all the desktop stuff into this one screen. If I go into nvidia settings I only see one physical device although all 3 are connected and have power. When I look into the xorg.conf I can still see my old setup with 3 devices, 3 screens, xinerama active etc... But I was totally unable to get 3 montitors to work. (I tried unplugging monitors, reconfiguring whole nvidia setup, ...) But it gets even better: When I restart my machine (i.e. choose the restart option from the Ubuntu menu) it shuts down and tries to restart. The restart then gets stuck after showing the Ubuntu splash screen with the 'loading bar' (the moving dots thingy) and I am forced to kill the machine by cutting power. But after the power cut the machine boots up normally and suddenly I get my 3 monitor setup back up working. That is until the next time I shut down and start up, where it all starts over again and I only have one monitor... (see above) I really have a hard time seeing where the error is. It must be that the restart boot somehow differs from the 'normal' boot. But the fact that it gets stuck and I need to cut power which then basically triggers a 'normal' boot does not really support this theory... My setup (please tell me if you need further info): 3 monitors as 3 screens as one desktop (with xinerama) 2 nvidia cards where screen 0 and 1 are on card 0 and screen 2 is on card 1 Ubuntu 10.04 Lucid Lynx (updated from 9.10, 9.04, ....) I would appreciate every idea on the subject, at the moment I really don't have any clue what to do...

  Read the article

• Web Site Serving, Cloud-Computing, oh, my

  - by Frank

  I'm planning a software based service. To give it a bit of context (type of traffic), assume it similar to facebook in nature (with a little GitHub thrown in). I've been trying to understand my different hosting options. I've been using a shared host with GoDaddy for years just fine. I currently host a Wordpress web site there and I've not had any problems. Quite frankly, they've taken good care of me. However, the nature of a shared hosting environment is limited in nature. For example, I can't do anything but host a web site there. For example, I can not run a Mercurial server. Last time I attempted to build a web application with the intention of eventually launching it via GoDaddy, I ran in to all sorts of troubles because it was shared-hosted. Assembly issues, etc. At the time, the cost and time sank my project. (The lack of direct access was also frustrating.) (to be fair to godaddy, this was over 3 years ago) I've been looking at Rackspace or Amazon as a possible cloud solution but it seems to be just processing power and bandwidth (and an OS). From what I understand, I'd need to get Apache and MySQL Working on my own. The way cloud hosting is priced, however, seems appealing. I figure my final option might be to use a virtual private host. I think this would be more flexible than a shared-host site but less scalable than a cloud based server. So, I guess my question is what is an appropriate solution for someone who intends to build a web application service? I figure that I need to establish a hosting environment now rather than later so I can plan to effectively use the environment. I'd prefer to be fairly economical to start out with. I really can't afford to pay $999 (or even $99) while I build up the site and get the core functionality online but at the same time, I'd like to have the selected environment grow as needed. Thank you.

  Read the article

• keyboard mappings are totally screwed after updating to kde4

  - by zeonglow

  I recently upgraded from KDE 3.5 to KDE 4, and I have been having weird issues with my keyboard. In one of the virtual consoles e.g. when I press ctrl + alt 1 , I can type perfectly, but in KDE, several of the number keys don't work, the left and right arrows don't work either. When I press the right arrow key in xev I get this: KeyRelease event, serial 34, synthetic NO, window 0x3600001, root 0x6f, subw 0x0, time 903459, (111,55), root:(115,836), state 0x10, keycode 114 (keysym 0x1008ff11, XF86AudioLowerVolume), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False When I press the '3' key it toggles my Bookmarks toolbar in Firefox, in xev I get this: KeyPress event, serial 34, synthetic NO, window 0x3600001, root 0x6f, subw 0x0, time 999968, (94,115), root:(98,896), state 0x10, keycode 12 (keysym 0x1008ff30, XF86Favorites), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False KeyRelease event, serial 34, synthetic NO, window 0x3600001, root 0x6f, subw 0x0, time 1000032, (94,115), root:(98,896), state 0x10, keycode 12 (keysym 0x1008ff30, XF86Favorites), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False As this is deeper down, changing the type of keyboard in the KDE meun's has no effect. I'm slowly beginning to wade through the mountains of documentation about the X keyboard model, but there has to be a better way. Does anyone no what it is? Edit: 1234567890 ! after deleting the entire .kde folder. but only until I change the Keyboard settings from the "system settings" applet, then its hosed full time. Regardless of what I set the settings too. (restore to default settings doesn't) 2nd Edit: I'm using Gentoo AMD64, I was upgrading from KDE 3.5 KDE 4.2. I think I had manual settings before, although I didn't change anything. I was originally running KDE without HAL until that stop working a year or so ago. The only customisation I made was to set the multimedia keys to control Amarok. 3rd Edit $ grep xkb /var/log/Xorg.0.log (**) Option "xkb_rules" "evdev" (**) Option "xkb_model" "evdev" (**) Option "xkb_layout" "us" (**) Option "xkb_rules" "evdev" (**) Option "xkb_model" "evdev" (**) Option "xkb_layout" "us" Xorg.0.log has this to say: (WW) AllowEmptyInput is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled. (WW) Disabling Mouse1 (WW) Disabling Keyboard1 My Xorg.conf has this in it. Identifier "Keyboard1" Driver "kbd" Option "AutoRepeat" "500 30" # Specify which keyboard LEDs can be user-controlled (eg, with xset(1)) Option "XkbRules" "xorg" Option "XkbModel" "pc105" Option "XkbLayout" "gb"

  Read the article

< Previous Page | 367 368 369 370 371 372 373 374 375 376 377 378  | Next Page >