Search Results

Search found 14015 results on 561 pages for 'extended desktop'.

Page 371/561 | < Previous Page | 367 368 369 370 371 372 373 374 375 376 377 378  | Next Page >

  • Dual booting Linux/Win7, Grub refuses to load Win7

    - by JohnB
    Decided to give Linux Mint a try (Ubuntu's interface annoys me), so I installed it with the intention of dual booting with Windows 7. Installation went fine, but now I can only boot into Linux Mint. Grub lists two Windows 7 menu options, but selecting either of them causes an "unknown file system" error and dumps me into a Grub recovery prompt. There, I have to manually reset the root and prefix options, as they reset hd0,msdos6 when they should be hd0,msdos5. I ran Boot Repair twice, once to fix grub errors, once to rebuild the MBR, but it didn't fix anything. Here is the log: http://paste.ubuntu.com/1029675/ fdisk output: Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 1486249145 743021149 7 HPFS/NTFS/exFAT /dev/sda3 1486249982 1953523711 233636865 5 Extended /dev/sda5 1486249984 1945141247 229445632 83 Linux /dev/sda6 1945143296 1953523711 4190208 82 Linux swap / Solaris grub.cfg: ### BEGIN /etc/grub.d/30_os-prober ### menuentry "Windows 7 (loader) (on /dev/sda1)" --class windows --class os { insmod part_msdos insmod ntfs set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root 86184D18184D091F chainloader +1 } menuentry "Windows 7 (loader) (on /dev/sda2)" --class windows --class os { insmod part_msdos insmod ntfs set root='(hd0,msdos2)' search --no-floppy --fs-uuid --set=root 56D84F84D84F60FB chainloader +1 } ### END /etc/grub.d/30_os-prober ### I have found a few similar troubleshooting guides so far, but so far no amount of updating/configuring Grub has been successful. Last resort is, I suppose, use the W7 recovery disc and start over. Thanks in advance! Linux Mint 13 Maya, 64-bit Windows 7 Home Edition, 64-bit

    Read the article

  • Cisco ASA: How to route PPPoE-assigned subnet?

    - by Martijn Heemels
    We've just received a fiber uplink, and I'm trying to configure our Cisco ASA 5505 to properly use it. The provider requires us to connect via PPPoE, and I managed to configure the ASA as a PPPoE client and establish a connection. The ASA is assigned an IP address by PPPoE, and I can ping out from the ASA to the internet, but I should have access to an entire /28 subnet. I can't figure out how to get that subnet configured on the ASA, so that I can route or NAT the available public addresses to various internal hosts. My assigned range is: 188.xx.xx.176/28 The address I get via PPPoE is 188.xx.xx.177/32, which according to our provider is our Default Gateway address. They claim the subnet is correctly routed to us on their side. How does the ASA know which range it is responsible for on the Fiber interface? How do I use the addresses from my range? To clarify my config; The ASA is currently configured to default-route to our ADSL uplink on port Ethernet0/0 (interface vlan2, nicknamed Outside). The fiber is connected to port Ethernet0/2 (interface vlan50, nicknamed Fiber) so I can configure and test it before making it the default route. Once I'm clear on how to set it all up, I'll fully replace the Outside interface with Fiber. My config (rather long): : Saved : ASA Version 8.3(2)4 ! hostname gw domain-name example.com enable password ****** encrypted passwd ****** encrypted names name 10.10.1.0 Inside-dhcp-network description Desktops and clients that receive their IP via DHCP name 10.10.0.208 svn.example.com description Subversion server name 10.10.0.205 marvin.example.com description LAMP development server name 10.10.0.206 dns.example.com description DNS, DHCP, NTP ! interface Vlan2 description Old ADSL WAN connection nameif outside security-level 0 ip address 192.168.1.2 255.255.255.252 ! interface Vlan10 description LAN vlan 10 Regular LAN traffic nameif inside security-level 100 ip address 10.10.0.254 255.255.0.0 ! interface Vlan11 description LAN vlan 11 Lab/test traffic nameif lab security-level 90 ip address 10.11.0.254 255.255.0.0 ! interface Vlan20 description LAN vlan 20 ISCSI traffic nameif iscsi security-level 100 ip address 10.20.0.254 255.255.0.0 ! interface Vlan30 description LAN vlan 30 DMZ traffic nameif dmz security-level 50 ip address 10.30.0.254 255.255.0.0 ! interface Vlan40 description LAN vlan 40 Guests access to the internet nameif guests security-level 50 ip address 10.40.0.254 255.255.0.0 ! interface Vlan50 description New WAN Corporate Internet over fiber nameif fiber security-level 0 pppoe client vpdn group KPN ip address pppoe ! interface Ethernet0/0 switchport access vlan 2 speed 100 duplex full ! interface Ethernet0/1 switchport trunk allowed vlan 10,11,30,40 switchport trunk native vlan 10 switchport mode trunk ! interface Ethernet0/2 switchport access vlan 50 speed 100 duplex full ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 switchport access vlan 20 ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! boot system disk0:/asa832-4-k8.bin ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server dns.example.com domain-name example.com same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network inside-net subnet 10.10.0.0 255.255.0.0 object network svn.example.com host 10.10.0.208 object network marvin.example.com host 10.10.0.205 object network lab-net subnet 10.11.0.0 255.255.0.0 object network dmz-net subnet 10.30.0.0 255.255.0.0 object network guests-net subnet 10.40.0.0 255.255.0.0 object network dhcp-subnet subnet 10.10.1.0 255.255.255.0 description DHCP assigned addresses on Vlan 10 object network Inside-vpnpool description Pool of assignable addresses for VPN clients object network vpn-subnet subnet 10.10.3.0 255.255.255.0 description Address pool assignable to VPN clients object network dns.example.com host 10.10.0.206 description DNS, DHCP, NTP object-group service iscsi tcp description iscsi storage traffic port-object eq 3260 access-list outside_access_in remark Allow access from outside to HTTP on svn. access-list outside_access_in extended permit tcp any object svn.example.com eq www access-list Insiders!_splitTunnelAcl standard permit 10.10.0.0 255.255.0.0 access-list iscsi_access_in remark Prevent disruption of iscsi traffic from outside the iscsi vlan. access-list iscsi_access_in extended deny tcp any interface iscsi object-group iscsi log warnings ! snmp-map DenyV1 deny version 1 ! pager lines 24 logging enable logging timestamp logging asdm-buffer-size 512 logging monitor warnings logging buffered warnings logging history critical logging asdm errors logging flash-bufferwrap logging flash-minimum-free 4000 logging flash-maximum-allocation 2000 mtu outside 1500 mtu inside 1500 mtu lab 1500 mtu iscsi 9000 mtu dmz 1500 mtu guests 1500 mtu fiber 1492 ip local pool DHCP_VPN 10.10.3.1-10.10.3.20 mask 255.255.0.0 ip verify reverse-path interface outside no failover icmp unreachable rate-limit 10 burst-size 5 asdm image disk0:/asdm-635.bin asdm history enable arp timeout 14400 nat (inside,outside) source static any any destination static vpn-subnet vpn-subnet ! object network inside-net nat (inside,outside) dynamic interface object network svn.example.com nat (inside,outside) static interface service tcp www www object network lab-net nat (lab,outside) dynamic interface object network dmz-net nat (dmz,outside) dynamic interface object network guests-net nat (guests,outside) dynamic interface access-group outside_access_in in interface outside access-group iscsi_access_in in interface iscsi route outside 0.0.0.0 0.0.0.0 192.168.1.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa-server SBS2003 protocol radius aaa-server SBS2003 (inside) host 10.10.0.204 timeout 5 key ***** aaa authentication enable console SBS2003 LOCAL aaa authentication ssh console SBS2003 LOCAL aaa authentication telnet console SBS2003 LOCAL http server enable http 10.10.0.0 255.255.0.0 inside snmp-server host inside 10.10.0.207 community ***** version 2c snmp-server location Server room snmp-server contact [email protected] snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart snmp-server enable traps syslog crypto ipsec transform-set TRANS_ESP_AES-256_SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set TRANS_ESP_AES-256_SHA mode transport crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group5 crypto dynamic-map outside_dyn_map 20 set transform-set TRANS_ESP_AES-256_SHA crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet 10.10.0.0 255.255.0.0 inside telnet timeout 5 ssh scopy enable ssh 10.10.0.0 255.255.0.0 inside ssh timeout 5 ssh version 2 console timeout 30 management-access inside vpdn group KPN request dialout pppoe vpdn group KPN localname INSIDERS vpdn group KPN ppp authentication pap vpdn username INSIDERS password ***** store-local dhcpd address 10.40.1.0-10.40.1.100 guests dhcpd dns 8.8.8.8 8.8.4.4 interface guests dhcpd update dns interface guests dhcpd enable guests ! threat-detection basic-threat threat-detection scanning-threat threat-detection statistics host number-of-rate 2 threat-detection statistics port number-of-rate 3 threat-detection statistics protocol number-of-rate 3 threat-detection statistics access-list threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200 ntp server dns.example.com source inside prefer webvpn group-policy DfltGrpPolicy attributes vpn-tunnel-protocol IPSec l2tp-ipsec group-policy Insiders! internal group-policy Insiders! attributes wins-server value 10.10.0.205 dns-server value 10.10.0.206 vpn-tunnel-protocol IPSec l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value Insiders!_splitTunnelAcl default-domain value example.com username martijn password ****** encrypted privilege 15 username marcel password ****** encrypted privilege 15 tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group Insiders! type remote-access tunnel-group Insiders! general-attributes address-pool DHCP_VPN authentication-server-group SBS2003 LOCAL default-group-policy Insiders! tunnel-group Insiders! ipsec-attributes pre-shared-key ***** ! class-map global-class match default-inspection-traffic class-map type inspect http match-all asdm_medium_security_methods match not request method head match not request method post match not request method get ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map type inspect http http_inspection_policy parameters protocol-violation action drop-connection policy-map global-policy class global-class inspect dns inspect esmtp inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect icmp inspect icmp error inspect mgcp inspect netbios inspect pptp inspect rtsp inspect snmp DenyV1 ! service-policy global-policy global smtp-server 123.123.123.123 prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily hpm topN enable Cryptochecksum:a76bbcf8b19019771c6d3eeecb95c1ca : end asdm image disk0:/asdm-635.bin asdm location svn.example.com 255.255.255.255 inside asdm location marvin.example.com 255.255.255.255 inside asdm location dns.example.com 255.255.255.255 inside asdm history enable

    Read the article

  • How can i get more low memory with the following setup:

    - by user539484
    Modules using memory below 1 MB: Name Total = Conventional + Upper Memory -------- ---------------- ---------------- ---------------- MSDOS 14 317 (14K) 14 317 (14K) 0 (0K) HIMEM 1 120 (1K) 1 120 (1K) 0 (0K) EMM386 3 120 (3K) 3 120 (3K) 0 (0K) OAKCDROM 36 064 (35K) 36 064 (35K) 0 (0K) POWER 80 (0K) 80 (0K) 0 (0K) NLSFUNC 2 784 (3K) 2 784 (3K) 0 (0K) COMMAND 2 928 (3K) 2 928 (3K) 0 (0K) MSCDEX 15 712 (15K) 15 712 (15K) 0 (0K) SMARTDRV 30 384 (30K) 13 984 (14K) 16 400 (16K) KEYB 6 752 (7K) 6 752 (7K) 0 (0K) MOUSE 17 296 (17K) 17 296 (17K) 0 (0K) DISPLAY 8 336 (8K) 0 (0K) 8 336 (8K) SETVER 512 (1K) 0 (0K) 512 (1K) DOSKEY 4 144 (4K) 0 (0K) 4 144 (4K) POWER 4 672 (5K) 0 (0K) 4 672 (5K) Free 552 944 (540K) 539 088 (526K) 13 856 (14K) Memory Summary: Type of Memory Total = Used + Free ---------------- ---------- ---------- ---------- Conventional 653 312 114 224 539 088 Upper 47 920 34 064 13 856 Reserved 0 0 0 Extended (XMS)* 64 898 256 2 671 824 62 226 432 ---------------- ---------- ---------- ---------- Total memory 65 599 488 2 820 112 62 779 376 Total under 1 MB 701 232 148 288 552 944 Total Expanded (EMS) 33 947 648 (33 152K Free Expanded (EMS)* 33 538 048 (32 752K * EMM386 is using XMS memory to simulate EMS memory as needed. Free EMS memory may change as free XMS memory changes. Largest executable program size 538 976 (526K) Largest free upper memory block 7 488 (7K) MS-DOS is resident in the high memory area. I'm running MS-DOS 6.22 on VMWare virtual hardware. This is memory state after memmaker pass, so i'm looking for optimization beyond memmaker. Note: NLS drivers (DISPLAY, KEYB, NSLFUNC) are essential for me. Thanks to @mtone for valuable reminder about MSCDEX /E which gave me 16KiB of low memory (see the diff)!

    Read the article

  • Can't reset Windows 7 Registry permissions.

    - by n10i
    hi all, i am trying to reset win 7 registry permissions using secedit /configure /cfg %windir%\inf\defltbase.inf /db defltbase.sdb /verbose /areas REGKEYS But i am receiving the following error: An extended error has occurred. The task has completed with an error. See log %windir%\security\logs\scesrv.log for detail info. The content Of the log file: ------------------------------------------- Friday, April 16, 2010 1:50:43 PM ----Configuration engine was initialized successfully.---- ----Reading Configuration Template info... ----Configure 64-bit Registry Keys... Configure users.default. Warning 5: Access is denied. Error taking ownership of users.default\software\SetID. Warning 5: Access is denied. Error opening users.default\software\SetID. Warning 5: Access is denied. Error setting security on users.default\software\SetID. Configure machine\software. Warning 5: Access is denied. Error setting security on machine\software. Warning 1336: The access control list (ACL) structure is invalid. Error setting security on machine\software\Macrovision. Configuration of Registry Keys was completed with one or more errors. ----Configure 32-bit Registry Keys... Configure machine\software. Warning 1336: The access control list (ACL) structure is invalid. Error setting security on machine\software\Audible. Configuration of Registry Keys was completed with one or more errors. ----Un-initialize configuration engine... plz! help me guys!

    Read the article

  • Ungrounded laptop (Macbook Pro) buzzes in headphones, weird feeling when fingers brush lightly

    - by donut
    I've got a nearly 3-year-old MacBook Pro 15" 2.16GHz (MacBookPro2,2). When I have am not using the extended, grounded adapter for the power supply, just using the simple, two-prong plug I can hear a buzzing when I use very sensitive earbuds. This goes away if I touch a metal part of the laptop. Also, I can feel a weird, fuzzy feeling when I brush the metal parts of the laptop lightly with my fingers/skin. Somewhat similar to feeling of a touching hair or a balloon that's charged with static electricity. But I'm not getting sparks or anything. And if I'm touching a metal part of my laptop solidly (not just brushing it) and then I touch someone else's skin I can feel the same effect and so can my victim. I've noticed similar effects with an ungrounded electric blanket. But with that the buzzing can be easily heard without headphones. Is this a defect, normal, or something else? And what exactly is happening?

    Read the article

  • Setting up a dualboot by installing cloned partitions using clonezilla

    - by Nimjox
    I'm trying to setup a dual boot system where I have Windows 7 and Linux Mint. Here's the kicker both are partitions I've saved using Clonzezilla from different places and to make matters worse Linux Mint is formated as a LVM. I need both of these images specifically as windows is a corporate image that I must use and the other is a development image that took me a week to setup. I've gotten it almost all working but my issue is that I can't get clonezilla to not mess up the partition table of Windows when installing Mint or vise-vera. I can use the (-k1 option) which doens't copy the partition table but then I have a unusable partition when it clones and I'm not sure how to fix the partition table. Here's what I'm doing: Using Gparted to make partitions sda1 40GB ntfs (windows), sda2 extended 70GB, sda5 lvm2 pv 69.99 GB (Linux), sda3 500MB (GRUB) Clonezilla windows image into sda1 partition (keeping partition table) Clonezilla linux image into sda5 partition (not recreating partition table) After all that I can boot into windows using the default MBR. I can use rescue-repair cd to reinstall GRUB which will see Windows 7 but I can't get it to see the Linux OS. I'm thinking its because of the sda5 partition but I'm not sure any ideas on what I could do to get this working or where I might be going wrong. If there is any additional detail you need please let me know and I'll edit as this is a lot.

    Read the article

  • Apache Logs - Not Showing Requested URL or User IP

    - by iarfhlaith
    Hey all, I'm having a problem with a server that keeps falling over. Looking through the Apache error logs it appears to come from a rogue PHP script. I'm trying to track this down using Apache's error_log and access_log but the server log format isn't giving me the detail I need. I suspect the log format isn't sufficient, but I've reviewed the Apache documentation and I've included the switches that I think I need to see. Here's my LogFormat configuration in the httpd.conf file: `LogFormat "%h %l %u %t \"%r\" %s %b %U %q %T \"%{Referer}i\" \"%{User-Agent}i\"" extended CustomLog logs/access_log extended` Using the %U %q %T switches I expected to see the requested URL, query string, and the time it took to serve the request, but I'm not seeing any of this information when I tail the log. Here's an example: 127.0.0.1 - - [01/Jun/2010:14:12:04 +0100] "OPTIONS * HTTP/1.0" 200 - * 0 "-" "Apache/2.2.15 (Unix) mod_ssl/2.2.15 OpenSSL/0.9.8e-fips-rhel5 mod_bwlimited/1.4 (internal dummy connection)" 127.0.0.1 - - [01/Jun/2010:14:12:05 +0100] "OPTIONS * HTTP/1.0" 200 - * 0 "-" "Apache/2.2.15 (Unix) mod_ssl/2.2.15 OpenSSL/0.9.8e-fips-rhel5 mod_bwlimited/1.4 (internal dummy connection)" 127.0.0.1 - - [01/Jun/2010:14:12:06 +0100] "OPTIONS * HTTP/1.0" 200 - * 0 "-" "Apache/2.2.15 (Unix) mod_ssl/2.2.15 OpenSSL/0.9.8e-fips-rhel5 mod_bwlimited/1.4 (internal dummy connection)" 127.0.0.1 - - [01/Jun/2010:14:12:07 +0100] "OPTIONS * HTTP/1.0" 200 - * 0 "-" "Apache/2.2.15 (Unix) mod_ssl/2.2.15 OpenSSL/0.9.8e-fips-rhel5 mod_bwlimited/1.4 (internal dummy connection)" 127.0.0.1 - - [01/Jun/2010:14:12:08 +0100] "OPTIONS * HTTP/1.0" 200 - * 0 "-" "Apache/2.2.15 (Unix) mod_ssl/2.2.15 OpenSSL/0.9.8e-fips-rhel5 mod_bwlimited/1.4 (internal dummy connection)" 127.0.0.1 - - [01/Jun/2010:14:12:09 +0100] "OPTIONS * HTTP/1.0" 200 - * 0 "-" "Apache/2.2.15 (Unix) mod_ssl/2.2.15 OpenSSL/0.9.8e-fips-rhel5 mod_bwlimited/1.4 (internal dummy connection)" Have a made a mistake in configuring the LogFormat or is it something else? Also, each request appears to come from the localhost. How come it's not giving me the remote user's IP address? Thanks, Iarfhlaith

    Read the article

  • W2K INACCESSIBLE_BOOT_DEVICE, with System Commander

    - by Gary Kephart
    I have a system that was originally had Win NT. I added System Commander (SC7) and then added W2K. The relevant partitions are: 0 - Primary - MultiFAT (Has Win NT, mapped to C:) 1 - Extended - with many logical partitions: 1.1 NTFS which has W2K and is mapped to D: 1.2 other logical partitions which are irrelevant to this D: was getting full. It needed room for virus definitions and Windows upgrades. In the past, I had simple used SC7 to resize D: without problems. So I did it again this time. However, upon finishing, I got the message "Unable to create partition". It also marked the partition as unformatted. I checked that the files on the disk were still there using SC7's Partition Explorer, and they were there. I continued and the system managed to boot up fine anyways. Then I rebooted the system again. This time, I got a message saying "INACCESSIBLE_BOOT_DEVICE". I went back in to SC7 and to Partition Commander, and it was still saying that the partition was unformatted but the Partition Explorer still showed the files on the system. I finally decided to resize the partition again, figuring that this would force a rewrite of the partition information. That seemed to work, until I had to reboot again. Now I can't see the files using Partition Explorer, and the Resize button is now disabled. What now?

    Read the article

  • Deploying workstations - best practices?

    - by V. Romanov
    Hi guys I've been researching on the subject of workstation deployment for a while, and found a ton of info and dozens different methods and tools, but no "best practice" method that doesn't lack at least one feature that i consider required for the solution to be perfect. I'm currently interested in windows workstation deployment, but if the tools can be extended to Linux, then it's an added value. I want the deployment tools I use to be able to do the following: hardware independent - I want my image or installation to have a minimum of hardware and driver dependency, so that i can use a single image/package for all workstations easily updatable - I want to be able to update my image as easily as possible without redeploying/rebuilding/reimaging all configurations PXE bootable deployment - I want the tools to be bootable off the network so that I don't need a boot cd/DOK. scriptable for minimum human input - Ideally, the tool should run automatically after being booted and perform a "default" deployment (including partitioning) unless prompted otherwise. i.e - take a pc, hook it up, power on, PXE boot and forget about it until the OS is deployed. I found no single product or environment that does all this. Closest i came to is the windows deployment services/WIM image format. I also checked out numerous imaging and deployment tools including clonezilla, ghost, g4u, wpkg and others, but most of them lack the hardware Independence and updatability features. We currently have a Symantec Ghost server setup that does imaging over the network, but I'm not satisfied with it as it has all the drawbacks i listed above. Do you have suggestions how to optimize the process of workstation deployment? How do you deploy them in your organization? Thanks! Vadim.

    Read the article

  • Windows XP dual screen problems, user account related

    - by Chris
    I have had this issue with a few laptops now and it looks like it is some sort of user account problem. Specifics of the system are: Dell Laptop Windows XP Pro SP3 Non-domain member computer DLP Projector connected to laptop via VGA I use this setup almost daily to do presentations, always the mirrored display mode where I can see on the laptop monitor the same thing that is displayed on the projector. Today, when I boot up, I get the mirrored display at the login screen, but after I log in, it switches to Extended Desktop (like two desktops side-by-side). Fn+F8 just cycles through all the normal settings except the mirrored display. I created a new user account on the computer and it performs normally. Mirrored display works as normal. I have run into this about 4 times now and it always can be solved by creating a new user account on the computer, and then all is well. I would like to either: 1. Find a way to reset the customized settings for a specific user account which would hopefully make this go away, or 2. Find the specific setting that causes this so that I can easily fix it when the problem comes up. Creating new user accounts is kind of a pain and a easy fix must be out there somewhere.

    Read the article

  • Unsigned lenny packages with aptitude safe-upgrade

    - by Liam
    I have several Debian lenny computers. Two have nearly identical sources.list files. On both, I do regular update/safe-upgrades. On one it always goes smoothly. On the other, much of the time I get the following: sudo aptitude safe-upgrade Reading package lists... Done Building dependency tree Reading state information... Done Reading extended state information Initializing package states... Done Reading task descriptions... Done The following packages will be upgraded: krb5-clients krb5-ftpd krb5-rsh-server krb5-telnetd krb5-user libimlib2 libkadm55 libkrb53 libpng12-0 libpulse0 xpdf xpdf-common xpdf-reader 13 packages upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 2906kB of archives. After unpacking 36.9kB will be used. Do you want to continue? [Y/n/?] WARNING: untrusted versions of the following packages will be installed! Untrusted packages could compromise your system's security. You should only proceed with the installation if you are certain that this is what you want to do. krb5-rsh-server krb5-user krb5-ftpd krb5-clients libkrb53 xpdf-reader libpng12-0 libkadm55 xpdf libpulse0 libimlib2 krb5-telnetd xpdf-common Do you want to ignore this warning and proceed anyway? To continue, enter "Yes"; to abort, enter "No": no Abort. Needless to say, I don't proceed. What is going on? How do I fix it? These are the non-comment lines in the sources.list for this computer: deb ftp://ftp.debian.org/debian/ lenny main contrib non-free deb-src ftp://ftp.debian.org/debian/ lenny main contrib deb http://security.debian.org/ lenny/updates main contrib non-free Thank you.

    Read the article

  • how to correctly mount fat32 partition in Ubuntu in order to preserve case

    - by Dean
    I've found there are couple of problems might be related how my FAT32 partition was mounted. I hope you can help me to solve the problem. I also included the command I used to help others when they find this post, sorry to those might feel I should use less space. I've the following file structures on my disk dean@notebook:~$ sudo fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x08860886 Device Boot Start End Blocks Id System /dev/sda1 * 1 13 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 13 5737 45978624 7 HPFS/NTFS /dev/sda3 5738 10600 39062047+ 83 Linux /dev/sda4 10601 19457 71143852+ 5 Extended /dev/sda5 10601 11208 4883728+ 82 Linux swap / Solaris /dev/sda6 11209 15033 30720000 b W95 FAT32 /dev/sda7 15033 19457 35537920 7 HPFS/NTFS In the etc/fstab I've got UUID=91c57a65-dc53-476b-b219-28dac3682d31 / ext4 defaults 0 1 UUID=BEA2A8AFA2A86D99 /media/NTFS ntfs-3g quiet,defaults,locale=en_US.utf8,umask=0 0 0 UUID=0C0C-9BB3 /media/FAT32 vfat user,auto,utf8,fmask=0111,dmask=0000,uid=1000 0 0 /dev/sda5 swap swap sw 0 0 /dev/sda1 /media/sda1 ntfs nls=iso8859-1,ro,noauto,umask=000 0 0 /dev/sda2 /media/sda2 ntfs nls=iso8859-1,ro,noauto,umask=000 0 0 I checked my id using id and I've got dean@notebook:~$ id uid=1000(dean) gid=1000(dean) groups=4(adm),20(dialout),24(cdrom),46(plugdev),103(fuse),104(lpadmin),115(admin),120(sambashare),1000(dean) I don't know why with these settings I still have problem of using svn like in this one Thank you for your help!

    Read the article

  • Openldap with ppolicy

    - by nitins
    We have working installation of OpenLDAP version 2.4 which is using shadowAccount attributes. I want to enable ppolicy overlays. I have gone through the steps provided at OpenLDAP and ppolicy howto. I have made the changes to slapd.conf and imported the password policy. On restart OpenLDAP is working fine and I can see the password policy when I do a ldapsearch. The user object looks like given below. # extended LDIF # # LDAPv3 # base <dc=xxxxx,dc=in> with scope subtree # filter: uid=testuser # requesting: ALL # # testuser, People, xxxxxx.in dn: uid=testuser,ou=People,dc=xxxxx,dc=in uid: testuser cn: testuser objectClass: account objectClass: posixAccount objectClass: top objectClass: shadowAccount shadowMax: 90 shadowWarning: 7 loginShell: /bin/bash uidNumber: 569 gidNumber: 1005 homeDirectory: /data/testuser userPassword:: xxxxxxxxxxxxx shadowLastChange: 15079 The password policy is given below. # default, policies, xxxxxx.in dn: cn=default,ou=policies,dc=xxxxxx,dc=in objectClass: top objectClass: device objectClass: pwdPolicy cn: default pwdAttribute: userPassword pwdMaxAge: 7776002 pwdExpireWarning: 432000 pwdInHistory: 0 pwdCheckQuality: 1 pwdMinLength: 8 pwdMaxFailure: 5 pwdLockout: TRUE pwdLockoutDuration: 900 pwdGraceAuthNLimit: 0 pwdFailureCountInterval: 0 pwdMustChange: TRUE pwdAllowUserChange: TRUE pwdSafeModify: FALSE I do not what should be done after this. How can the shadowAccount attributes be replaced with the password policy.

    Read the article

  • Hard drive had reallocated sectors...but now it magically doesn't! Can I trust it?

    - by rob
    Last week my SMART diagnostics utility, CrystalDiskInfo, reported that the external hard drive that I was saving my backups to had suddenly reported 900+ reallocated sectors. I double-checked to confirm, then ordered a replacement drive. I spent all of this week copying data from that drive to the new drive. But toward the end of the copy, something peculiar happened. CrystalDiskInfo popped up an alert that the reallocated sector count had gone back down to 0. I know that when SMART detects a read error on a block, it adds that block to the current pending reallocation list. If it subsequently is successfully written or read later, it is removed from the list and assumed to be fine, but if a subsequent write fails, it is marked bad and added to the reallocated sector count. What concerns me most is that I've never read anywhere that a sector can be recovered as "good" after it has been marked as a bad sector and remapped. I've just finished running an extended SMART diagnostic, and it found no surface errors. Now I'm doubtful that the manufacturer will honor a warranty claim if the SMART info does not report any problems. Has anyone had this happen? If so, then is the drive, indeed, okay, or should I be concerned about an imminent failure?

    Read the article

  • Ubuntu 13.04 to 13.10: Filesystem check or mount failed [migrated]

    - by SamHuckaby
    I attempted to upgrade from Ubuntu 13.04 to 13.10 today, and mid upgrade the system started flaking out, and eventually locked up entirely. I was forced to restart the computer, and am now unable to get the computer to boot up at all. When I boot currently, it takes me to the GRUB menu, and I can choose to boot normally, or boot in an older version. I have tried several things, which I list below, but no matter what, when I try to finish booting into Ubuntu, I receive the following error: Filesystem check or mount failed. A maintenance shell will now be started. CONTROL-D will terminate this shell and continue booting after re-trying filesystems. Any further errors will be ignored root@ubuntu-computername:~# I have fun fsck -f and everything appears correct, no errors are reported. and it passes all 5 checks. If I run fdisk -l then I get the following information: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 4096 bytes / 4096 bytes Disk identifier: 0x00010824 Device Boot Start End Blocks Id System /dev/sda1 * 2048 608456703 304227328 83 Linux /dev/sda2 608458750 625141759 8341505 5 Extended Partition 2 does not start on physical sector boundary. /dev/sda5 608458752 625141759 8341504 82 Linux swap / Solaris Disk /dev/sdb: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0fb4b7e8 Device Boot Start End Blocks Id System /dev/sdb1 8192 625139711 312565760 7 HPFS/NTFS/exFAT I am considering just installing a new OS on the other disk, that currently has nothing on it, and then just attempting to scrape my data off the old disk (thankfully I didn't encrypt the files). Really my question is this: Can I salvage this Ubuntu install, or should I give up and just reinstall?

    Read the article

  • Extend RAID 1 (HP SmartArray P410i) running Linux

    - by Oliver
    I took over a fairly simple server setup with the following RAID 1 config running Ubuntu 11.10 (Kernel 3.0.0-12-server x86_64): => ctrl all show config Smart Array P410i in Slot 0 (Embedded) (sn: removed) array A (SAS, Unused Space: 1335535 MB) logicaldrive 1 (279.4 GB, RAID 1, OK) physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 1 TB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 1 TB, OK) Initially there were two 300GB disks that got replaced by 1TB disks and I now have to extend the logical volume to use that extra space. However, when trying to do so I get the following warning: => ctrl slot=0 ld 1 modify size=max Warning: Extension may not be supported on certain operating systems. Performing extension on these operating systems can cause data to become inaccessible. See ACU documentation for details. Continue? (y/n) Is it safe to say yes or am I at risk of corrupting the file system / loosing data? Rearranging and extending the file system afterwards shouldn't be an issue as I can take the server offline and boot from a gparted live disk. Here's the config of the RAID controller in use: => ctrl all show detail Smart Array P410i in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Serial Number: removed RAID 6 (ADG) Status: Disabled Controller Status: OK Hardware Revision: Rev C Firmware Version: 5.12 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: False Drive Write Cache: Disabled SATA NCQ Supported: True And the partition table: Number Start End Size Type File system Flags 1 1049kB 274GB 274GB primary ext4 boot 2 274GB 300GB 25.8GB extended 5 274GB 300GB 25.8GB logical linux-swap(v1)

    Read the article

  • a disk read error occurred

    - by kellogs
    Hi, ¨a disk read error occurred¨ appears on screen after choosing to boot into Windows XP from GRUB. [root@localhost linux]# fdisk -lu Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x48424841 Device Boot Start End Blocks Id System /dev/sda1 63 204214271 102107104+ 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 204214272 255606783 25696256 af HFS / HFS+ Partition 2 does not end on cylinder boundary. /dev/sda3 255606784 276488191 10440704 c W95 FAT32 (LBA) Partition 3 does not end on cylinder boundary. /dev/sda4 276490179 312576704 18043263 5 Extended /dev/sda5 * 276490240 286709759 5109760 83 Linux /dev/sda6 286712118 310488254 11888068+ b W95 FAT32 /dev/sda7 310488318 312576704 1044193+ 82 Linux swap / Solaris sda is a 160GB hard disk with quite a few partitions and 3 OSes installed. I am able to boot into Linux and Mac OS fine, but not into Windows anymore. The Windows system is located on /dev/sda1. I can not recall how exactly have I used testdisk but it once said that ¨The harddisk /dev/sda (160GB / 149 GB) seems too small! (< 172GB / 157GB)¨ or something simillar. So far I have tried to ¨fixboot¨ and ¨chkdsk¨ from a recovery console on the affected windows partition (/dev/sda1), the plug off power cord for 15 seconds trick, reinstalling GRUB, repairing the MFT and boot sector of the affected partition via testdisk, what next please ? Thank you!

    Read the article

  • What could cause the file command in Linux to report a text file as data?

    - by Jonah Bishop
    I have a couple of C++ source files (one .cpp and one .h) that are being reported as type data by the file command in Linux. When I run the file -bi command against these files, I'm given this output (same output for each file): application/octet-stream; charset=binary Each file is clearly plain-text (I can view them in vi). What's causing file to misreport the type of these files? Could it be some sort of Unicode thing? Both of these files were created in Windows-land (using Visual Studio 2005), but they're being compiled in Linux (it's a cross-platform application). Any ideas would be appreciated. Update: I don't see any null characters in either file. I found some extended characters in the .cpp file (in a comment block), removed them, but file still reports the same encoding. I've tried forcing the encoding in SlickEdit, but that didn't seem to have an effect. When I open the file in vim, I see a [converted] line as soon as I open the file. Perhaps I can get vim to force the encoding?

    Read the article

  • Dual-booting Ubuntu and Pardus with GRUB2...Pardus no show?

    - by Ibn Ali al-Turki
    Hello all, I have Ubuntu 10.10 installed and used to dual-boot Fedora, but I replaced Fedora with Pardus. After the install, I went into ubuntu, and did a sudo update-grub. It detected my Pardus 2011 install there. When I rebooted, it did not show up in my grub2 menu however. I went back to Ubuntu and did it again...then checked the grub.cfg, and it is not there. I have read that Pardus uses a grub legacy. How can I get Pardus into my grub2 menu? Thanks! sudo fdisk -l Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xd9b3496e Device Boot Start End Blocks Id System /dev/sda1 * 1 15197 122067968 83 Linux /dev/sda2 36394 60802 196059757 5 Extended /dev/sda3 15197 30394 122067968 83 Linux /dev/sda5 36394 59434 185075308 7 HPFS/NTFS /dev/sda6 59434 60802 10983424 82 Linux swap / Solaris Partition table entries are not in disk order and update-grub Found linux image: /boot/vmlinuz-2.6.35-25-generic Found initrd image: /boot/initrd.img-2.6.35-25-generic Found memtest86+ image: /boot/memtest86+.bin Found Pardus 2011 (2011) on /dev/sda3 Yet after this, I go to grub.cfg, and Pardus is not there.

    Read the article

  • Cannot increase Datastore

    - by k4w4zz
    Hello, We have an ESX 4.0 cluster with 2 hosts, EMC Clarion SAN storage with 10 LUNs. We have added 2 new 400 GB LUNs. All the LUNs are visible from both hosts. I have extended an existing 500 GB datastore with one of these 400 GB LUNs - the new datastore size is now 900 GB. I'd like to do the same operation with the second 400 GB LUN to extend another existing datastore but I'm not able to do it. The LUN is available to create a brand new datastore but is not visible to extend an existing one. I don't understand why everything was fine with the other one and why can't I do the same exact operation with this LUN. The result is the same on both hosts. The SAN admin have erased and re-created several times this LUN. I have rescan the HBA each time. In attachment you can find the result of the esxcfg-mpath -l and fdisk -l commands on both servers. Does somebody have an idea please?

    Read the article

  • How to crop Screen Recordings under Snow Leopard?

    - by willc2
    Quicktime Player for Snow Leopard now allows you record the screen. Awesome! Once you have a movie it will let you trim screen recordings for length. Is there a way to crop the movie's dimensions, either in QT or using some built-in or free software? Update: How to crop to an arbitrary size and aspect ratio? iMovie only seems to let you crop to the aspect ratio of the containing project. Result: Both good answers but since I have QuickTime Player 7 and Photoshop, that's the workflow I choose as the answer. NOTE: If you have Photoshop Extended, you can import a movie, use the crop tool, and Export the cropped movie. Not free or built-in, but convenient. To summarize the instructions from the video link ricbax posted: Open movie in QuickTime Player 7 Copy a frame and Paste it into a new document in Photoshop Draw a rectangular selection around the area to keep and fill with black Invert the selection and fill with white Save as .GIF, with 2 colors Back in QuickTime Player 7, open Movie Properties window Select the Video Track Select the Visual Settings Tab Drag and Drop the 2-color .GIF file onto the Mask drop area (or use choose file button) Export the (now cropped) movie DONE

    Read the article

  • Expand disk space on Ubuntu 10.04 (VMWare Guest)

    - by Jason Clawson
    I need to resize the disk space of an ubuntu guest in VMWare Workstation. After using the expand disk utility in vmware workstation, I need to do some linux magic to resize the parition. I have searched and found a lot of posts about resizing it. Unfortunately I don't really understand it all that well. Can anyone help me out with this? df -h gives me: Filesystem Size Used Avail Use% Mounted on /dev/mapper/ubuntu-root 19G 2.6G 16G 15% / none 496M 172K 495M 1% /dev none 500M 0 500M 0% /dev/shm none 500M 64K 500M 1% /var/run none 500M 0 500M 0% /var/lock none 500M 0 500M 0% /lib/init/rw none 19G 2.6G 16G 15% /var/lib/ureadahead/debugfs /dev/sda1 228M 36M 181M 17% /boot lvs says: LV VG Attr LSize Origin Snap% Move Log Copy% Convert root ubuntu -wi-ao 18.88g swap_1 ubuntu -wi-ao 884.00m fdisk -l says: Disk /dev/sda: 21.5 GB, 21474836480 bytes 255 heads, 63 sectors/track, 2610 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00033718 Device Boot Start End Blocks Id System /dev/sda1 * 1 32 248832 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 32 2611 20719617 5 Extended /dev/sda5 32 2611 20719616 8e Linux LVM I really appreciate the help.

    Read the article

  • How to fix Quicktime video color problems on nVidia chipset and Windows XP?

    - by Matthew Glidden
    My laptop frequently plays video as if in very low-color mode. Though the sound remains clear, it looks terrible, showing only a few shades of red, blue, or yellow. (It's even worse than 8-bit color.) The problem doesn't happen consistently, so I'm looking for troubleshooting advice or known solutions. I use a Dell Latitude D620 laptop with Windows XP, on-board nVidia video chipset, Quicktime, and multiple monitors (laptop screen + VGA-connected LCD). Color problems happen in each application I tried, iTunes, a browser, and the Quicktime standalone player. It doesn't happen right after reboot, so could be from a sleep-wake cycle, or at least being on for an extended period. Google results suggest reinstalling nVidia drivers, which I've done several times with no change. I have found 2 workarounds. Reboot, sacrificing significant time and disrupting work In nVidia control panel, change color to 16-bit, and then back to 32-bit This happens with all video playback, so it's definitely not one corrupt file. I use workaround #2 consistently, but would love a longer-term solution.

    Read the article

  • SSO "Portal"

    - by Clinton Blackmore
    Pursuant to my question on alleviating the password explosion, I've contacted some of the services to whom we are paying money to access their websites to ask if we could authenticate our own users, and some of them said yes and send me specs on how to do so. (One of the sites called such a system a page a "portal"; I've never heard the term used in quite that way.) It is simple enough that I am tempted to roll my own. The largest complication is that one site wants us to store a key for every user in our database (and I think the LDAP database makes sense) after their initial login. So, non-trivial, but doable. The nature of these sorts of tasks, I expect, is that if they start out small and simple, they don't end that way. There must be some software that addresses this that is readily extended, surely. In my searching, I've come across: SimpleSAMLphp JOSSO RubyCAS-Server Shibboleth Pubcookie OpenID [Wow, gee. I'd missed some of those in my previous searches! The wikipedia page on Central Authentication Services is useful, and the section on Alternatives to OpenID makes it look like there is a lot of choice.] Can anyone recommend any of these, or suggest ones to avoid? Internally, we are authenticating using Apple's Open Directory [ == OpenLDAP + Kerberos + Password Server (which, I believe, == SAML) ]. As far as extending/tweaking/advanced configuration of a system, I am able to program in Python, C++, can do some basic PHP, and may be able to remember some Java. Looks like I need to pick up Ruby at some point. Addendum: I would also like users to be able to change their passwords over the web (and for certain users to change passwords of other users).

    Read the article

  • Probability of Blade Chassis Failure

    - by ChrisZZ
    In my organisation we are thinking about buying blade servers - instead of rack servers. Of course technology vendors also make them sound very nice. A concern, that I read very often in different forums, is, that there is a theoretical possibility of the server chassis going down - which would in consequence take all the blades down. That is due to shared infrastructure. My reaction on this probability would be to have redundancy and by two chassis instead of one (very costly of course). Some people (including e.g. HP Vendors) try to convince us, that the chassis is very very unlikely to fail, due to many redundancies (redundant power supply, etc.). Another concern on my side is, that if something goes down, spare parts might be required - which is difficult in our location (Ethiopia). So I would ask to experienced administrators, that have managed blade server: What is your experience? Do they go down as a whole - and what is the sensible shared infrastructure, that might fail? That question could be extended to shared storage. Again I would say, that we need two storage units instead of only one - and again the vendors say, that this things are so rock solid, that no failure is expected. Well - I can hardly believe, that such a critical infrastructure can be very reliable without redundancy - but maybe you can tell me, whether you have successfull blade-based projects, that work without redundancy in its core parts (chassis, storage...) At the moment, we look at HP - as IBM looks much to expensive... thanks a lot best regards Christian

    Read the article

< Previous Page | 367 368 369 370 371 372 373 374 375 376 377 378  | Next Page >