Search Results

Search found 11331 results on 454 pages for 'resource monitor'.

Page 371/454 | < Previous Page | 367 368 369 370 371 372 373 374 375 376 377 378  | Next Page >

• Low-profile, PCI Express, x1 video card with VGA-out?

  - by Dandy

  I just bought an Acer Aspire EasyStore H340 system (http://us.acer.com/acer/productv.do?LanguageISOCtxParam=en&kcond61e.c2att101=54825&sp=page16e&ctx2.c2att1=25&link=ln438e&CountryISOCtxParam=US&ctx1g.c2att92=450&ctx1.att21k=1&CRC=936243954) It comes with Windows Home Server, which I don't particularly care for (too dumbed down for my liking)--I bought the box mainly for the form factor, and intend to install Server 2008 on it and have it run as a small domain controller. The geniuses at Acer however went out of their way to ensure you can only run Home Server--you can only connect to it via the Home Server Connector software, as it has no video-out whatsoever (so essentially, there's no way to even get into the BIOS). It only has a low-profile, PCI Express x1 slot. It turns out to be way harder than I thought to locate a video card that both has an x1 connector, and is low-profile (I'd really rather not snip the bracket at the back just so it'll fit the case). I know they're out there, and I've seen one with Display Port outputs, but I don't have a monitor with this connection. So to reiterate, it needs to be: - x1 connector - low profile - VGA out (though DVI would be okay; I have some spare adapters) Can anyone recommend anything at all?

  Read the article

• Subversion error: Repository moved permanently to please relocate

  - by Bart S.

  I've set up subversion and apache on my server. If I browse to it through my webbrowser it works fine (http://svn.host.com/reposname). However, if I do a checkout on my machine I get the following error: Command: Checkout from http://svn.host.com/reposname, revision HEAD, Fully recursive, Externals included Error: Repository moved permanently to 'http://svn.host.com/reposname/'; please relocate I checked apache's error log, but it doesn't say anything. (it does now - see edit) My repositories are stored under: /var/www/svn/repos/ My website is stored under: /var/www/vhosts/x/... Here's the conf file for the subdomain: <Location /> DAV svn SVNParentPath /var/www/svn/repos/ AuthType Basic AuthName "Authorization Realm" AuthUserFile /var/www/svn/auth/svn.htpasswd Require valid-user </Location> Authentication works fine. Does anyone know what might be causing this? -- Edit So I restarted apache (again) and tried it again and now it give me an error message, but it doesn't really help. Anyone have an idea what it means? [Wed Mar 31 23:41:55 2010] [error] [client my.ip.he.re] Could not fetch resource information. [403, #0] [Wed Mar 31 23:41:55 2010] [error] [client my.ip.he.re] (2)No such file or directory: The URI does not contain the name of a repository. [403, #190001] -- Edit 2 If I do svn info it doesn't give anything usefull: [root@eduro eduro.nl]# svn info http://svn.domain.com/repos/ Username: username Password for 'username': svn: Repository moved permanently to 'http://svn.domain.com/repos/'; please relocate I also tried doing a local checkout (svn checkout file:///var/www/svn/repos/reposname) and that works fine (also adding / commiting works fine). So it seems is has something to do with apache. Some other information: I'm running CentOs 5.3 Plesk 9.3 Subversion, version 1.6.9 (r901367) -- Edit 3 I tried moving the repositories, but it didn't make any difference. selinux is disabled so that isn't it either. -- Edit 4 Really? Nobody :(?

  Read the article

• How can I confirm that burn process was completed successfully??

  - by infant programmer

  Just now I tried to make a duplicate copy of my Windows XP Pro SP3 CD. I had set 32X speed while the max speed allowed is 48X. And checked "Verify the Data after burning". I didn't observe how much % did it complete. But after 15 mins (which is sufficient period to burn disc), I heard "Fatal Error" sound. When I saw the monitor, There was a message box which was showing "Error while burning Disc", I saved the error log which you can find here click_me. How do I acknowledge that burning process is done?? Well. my PC is able to read the CD and CD is bootable too.. I am not sure .. whether the burning process got failed or the verify Process! Please let me know if you have come across or aware of such situation .. As it is XP installation CD .. I don't want to do trial and error method. regards,

  Read the article

• Windows 7 Paging file apparently not being used

  - by Daniel F.

  I'm running Windows 7 Home Premium 32bit on a mobo with 24GB RAM. Of those 24GB, 20GB are assigned as a RAMDISK via ASRock XFastRAM. This RAMDISK has the drive letter X assigned to it. On X:\ I'm storing the temporary files folder, as well as pagefile.sys. Pagefile.sys has 6GB of size. The X:\ has usually around 14GB free space, so the temporary files are negligible, it's mostly the browsers which are storing their caches on there. Now my issue is that Firefox is crashing a lot on me, no error message pops up, but I know that this is because it's out of memory. I could kind of live with that, but now that I switched from using Eclipse to Android Studio, I know that I'm in trouble, because Java isn't capable of allocating, and Android Studio, together with the Java instances it launches, is quite a memory hog. So I tried to figure out what's wrong, and apparently Windows isn't swapping out memory onto the paging file. While my applications are crashing (firefox) / not starting (java vm's), the paging file is only using constantly around 15% of its size (checked with the performance monitor). 15% equals to 1GB aprox. I know that the correct solution would be to switch to 64 bit Windows, but I had to use the 32 bit version because of driver issues which I had about two years ago, and I guess that I'll have them again if I reformat and install the 64 bit version. Also, the machine is running quite stable, the only issue is the memory, so I'd like to use it as it is (as the apps are installed and configured) Is there a way to make Windows use the paging file more efficiently? None of my processes require more than 1GB, I'd just like it to swap out some seldomly used stuff, like GoogleCrashHandler.exe and stuff like that in order to have "more physical memory avaliable". Is that possible?

  Read the article

• Dual DC Time Service

  - by poconnor

  I believe I'm having an issue with my Domain Controllers and Time Server. On my back up DC, I keep seeing a warning stating "The time service has stopped advertising as a time source because the local clock is not synchronized." Does this mean that my backup DC believes it's a Time Server? My PDC should be the time server and I have gone through setting up the PDC as the time server. I was not around for the original setup of the time server with the old PDC and Backup DC. But I believe the old PDC was the time server so I setup the new PDC as the new time server, when I decommissioned the old PDC. Is it possible that the Backup DC was setup as the time server and it still thinks it's suppose to be giving out time to everyone? Registry for PDC has NTP Registry for Backup has NT5D5 Results of w32tm /monitor Getting AD DC list for default domain... Analyzing:delayoffset from DC1.local..com Stratum: 4 delayoffset from DC1.local..com Stratum: 3 Warning: Reverse name resolution is best effort. It may not be correct since RefID field in time packets differs across NTP implementations and may not be using IP addresses. DC2.local..com[192.168.1.8:123]: ICMP: 1ms NTP: -0.6349491s RefID: DC1.local..com [192.168.1.9] DC1.local..com *** PDC ***[192.168.1.9:123]: ICMP: 0ms NTP: +0.0000000s RefID: wwwco1test12.microsoft.com [65.55.21.20]

  Read the article

• Clone Microsoft VM > SharePoint issues

  - by Rob

  Hi, We have an existing (production) Hyper-V VM that I want to clone to create a staging server. This server is NOT on a domain/active-directory - uses all local computer accounts. It is Windows 2008 OS, SharePoint 2007, SQL server 2008, Reporting Services, and some custom line-of-business web-applications. We rename the server etc as per the documentation we have, but are having troubles specifically with SharePoint. Some of the sites do not come up, and some issues adding/updating site settings such as site owners. Does anyone know of a definitive resource to this process? thanks Update: We seem to have most working, but the Shared Service Provider, and the SSP's admin site, are not working. In addition, the custom web-parts that reference IIS Session objects are failing (which seem to be related to the Share Service Provider). All the Windows user accounts for various services are renamed during the server cloning, but the windows account names in SQL server are not automatically changed. We've tried to change them in SQL server but still does not seem to work Seems like allot of work - and am thinking that there must be some guidance out there. also getting this: NullReferenceException: Object reference not set to an instance of an object.] Microsoft.Office.Server.Administration.SqlSessionStateResolver.System.Web. IPartitionResolver.ResolvePartition(Object key) +135

  Read the article

• Server 2008 R2 & Domain Trusts - Attempt to Compromise Security

  - by SnAzBaZ

  We have two separate Active Directory domains; EUROPE and US. There is a two way trust between the domains / forests. I have a group of users called "USA Staff" that have access to certain shares on servers in the EUROPE domain and a group called "EUROPE Staff" which have access to shares in the USA domain. Recently the USA PDC was upgraded to Windows Server 2008 R2. Now when I try to access a share on a USA server from a Windows 7 workstation in the EUROPE domain I get the "Please enter your username / password" dialog box appear, with a message at the bottom: "The system has detected a possible attempt to compromise security." When I enter a username / password for a user in the USA domain, I can then access the network resource. Entering credentials for a EUROPE user however does not give me access, even though my NTFS and Share permissions are set to allow that. Windows Server 2003 / Windows Server 2008 did not have this problem, it seems to be unique to R2. I found KB938457 and opened up port 88 on the Server 2008 R2 firewall but it did not make any difference. Any other suggestions as to what to turn off in R2 to get this working again ? Thanks

  Read the article

• Nginx: Disallow index.html in URL

  - by Martin Vilcans

  We're generating a site consisting of only static files (using Assemble). Having the .html extension on URLs looks so nineties, so we generate every static HTML file in its own directory and call it index.html. For example, the url http://www.example.com/foo/bar/ is in the file /var/www/foo/bar/index.html. This works well, but there is one small thing nagging me: Now there are two possible URLs to the same resource: http://www.example.com/foo/bar/ (slash URL) http://www.example.com/foo/bar/index.html (index.html URL) By accident someone may link to the index.html form of the URL, which is bad for SEO and looks ugly (remember the nineties?). Is it possible in Nginx to give a 404 error on the index.html URL, but serve the slash URL? I tried this: location ~ /index\.html$ { return 404; } But it seems that Nginx does some internal rewrite of the slash URL to the index.html URL, and then matches this location so we get a 404 even on the slash URL. Note that to catch mistakes, we want index.html URLs to be an error, not just redirect to the slash URL.

  Read the article

• Starting old computer - nothing shown on screen at boot

  - by Jonas

  I'm trying to start an about 10 years old PC computer. But nothing is shown on the screen, and it beeps everytime I press a key on the keyboard. I can press Ctrl+Alt+Del to reboot the computer. The monitor is newer and seem to work with other computers. I don't see anything from POST/BIOS at start or later. I have tried to change to another graphic card, but it didn't change anything. What can I do to solve this problem? Update: I have now tried with another computer (the one where the "another graphic card" came from) and I got the same problem. I doesn't show anything on the screen. Both these computers had a GeForce2 MX 400 graphic card. I tried with another computer screen it didn't work - it was showing "signal out of range". So is the graphic card GeForce2 MX 400 too old for newer TFT-monitors? I tried with a third computer so I know that the monitors are working, and both monitors work fine with that computer.

  Read the article

• Rkhunter reports file properties have changed

  - by CountMurphy

  I am running a fully updated LTS copy of Ubuntu server. Today I ran rkhunter (as I do from time to time). This is the output I got: Warning: The file properties have changed: [15:52:25] File: /bin/ps [15:52:25] Current hash: f22991ec93ae966c856d367f42fc3d8a484bd827 [15:52:25] Stored hash : 1892268bf195ac118076b1b0f53e7a637eb6fbb3 [15:52:25] Current inode: 142902 Stored inode: 130894 [15:52:25] Current file modification time: 1324307913 (19-Dec-2011 07:18:33) [15:52:25] Stored file modification time : 1260992081 (16-Dec-2009 11:34:41) Warning: The file properties have changed: [15:52:33] File: /usr/bin/ldd [15:52:33] Current hash: f1e2ca5aa3a28994e2cebb64c993a72b7d97b28c [15:52:33] Stored hash : 295d9cedb121a5e431a39a6d201ecd7ce5640497 [15:52:33] Current inode: 2236210 Stored inode: 2234359 [15:52:33] Current size: 5280 Stored size: 5279 [15:52:33] Current file modification time: 1331165514 (07-Mar-2012 16:11:54) [15:52:33] Stored file modification time : 1295653965 (21-Jan-2011 15:52:45) Warning: The file properties have changed: [15:52:37] File: /usr/bin/pgrep [15:52:37] Current hash: 3eada9a96760f3e2c9111cfe32901d1432813c1d [15:52:37] Stored hash : ce265d0db9964b173fe5036f703a9b8d66e55df3 [15:52:37] Current inode: 2229646 Stored inode: 2224867 [15:52:37] Current file modification time: 1324307913 (19-Dec-2011 07:18:33) [15:52:37] Stored file modification time : 1260992081 (16-Dec-2009 11:34:41) Warning: The file properties have changed: [15:52:41] File: /usr/bin/top [15:52:41] Current hash: 6be13737d8b0950cea2f1ae3a46d4af713dbe971 [15:52:41] Stored hash : c7b495ecef3982eeb6f08a511861b1a1ae8775e6 [15:52:41] Current inode: 2229629 Stored inode: 2224862 [15:52:41] Current file modification time: 1324307913 (19-Dec-2011 07:18:33) [15:52:41] Stored file modification time : 1260992081 (16-Dec-2009 11:34:41) Warning: The file properties have changed: [15:52:53] File: /usr/sbin/cron [15:52:53] Current hash: e783ca973f970aa8a4bf5edc670e690b33914c3d [15:52:53] Stored hash : 4718257a8060736b9058aed025c992f02a74a5a7 [15:52:53] Current inode: 2224719 Stored inode: 2228839 [15:52:54] Current file modification time: 1330965568 (05-Mar-2012 08:39:28) There were also a few other I left out. Has my server been rooted? I am running fail2ban and do monitor failed ssh logins. nothing has come up. Could someone compare these hashes to their copy of Ubuntu Server (lts)? Please tell me these are false positives..... Edit: is something else like rkhunter I can run for a second scan?

  Read the article

• 2012 R2 services will not start after promotion to Domain Controller

  - by Cybersylum

  Having a peculiar issue promoting a Windows 2012 R2 server in a domain at 2003 domain/forest functional level. Built a new 2012 R2 server, added the following software (labtech, appassure, eset A/V, & Teamviewer). It activated and appeared to be working fine. I added the Active Directory Domain Services role, and completed the configuration (Domain/Forest Prep, and DC promotion). All appeared to go well. I rebooted the server, and that's where the peculiar stuff began. I noticed the server indicated it needed activated again; but would not accept the key. I verified the key was good. That's when I noticed the Software Protection service (as well as many other core services - Base Filtering engine, DHCP client, firewall, etc) would not start. The error message for all of them was "Access Denied". I called MS, and they wanted to troubleshoot at a service level. Their fix was to use procmon and identify the resource that needed permissions (registry key, file or folder) and add "everyone" with full control). That got the services to start; but the problem re-appeared after a reboot. Thinking the issue might have been with the anti-virus package during the promotion process, I rebuilt the DCs from scratch and removed the metadata from AD (as I could not demote the machines "rpc server unavailble"). I tried to promote the newly built machines again. The only changes to the brand new machines being critical updates. Again the promotion appeared to work fine; but upon reboot (and a long wait to allow replication to occur) similar problems began to re-appear. I have verified that the schema updates are correct (schema version is 69 - for Windows 2012 R2). I am not finding much about this issue through my own searches, so I thought I would post this to see if anyone else has seen anything similar...

  Read the article

• ability to see free/busy detail information for conference rooms in Outlook 2007 and Microsoft hosted Exchange solution

  - by Malav

  recently my company migrated from an in-house Exchange server to the Microsoft hosted exchange online solution. My client is Outlook 2007. Before the migration, I could see the details of the meetings when I hovered on the busy blue bar for a resource such as a conference room. I could click on the meetings and see the invite list and the contents of the meeting. Ofcourse if the meeting was marked as private I could not. however after the migration to the online solution, I cannot see the detailed information. I can still see if the room is busy or not but I can no longer see the details of that meeting. The IT folks can see the information and they claim that they can see it because they have full admin rights. It is their claim that in the hosted Exchange solution you can either have full access (admin access) and see the details or not see anything but just that the room is busy. there is no middle ground such as being able to see the details of the meeting but not having any admin rights. For some reason I believe this to be not true. Can someone please verify my doubts and inform me of what needs to be done to see that information if my IT folks are wrong? thanks

  Read the article

• Bandwidth monitoring with iptables for non-router machine

  - by user1591276

  I came across this tutorial here that describes how to monitor bandwidth using iptables. I wanted to adapt it for a non-router machine, so I want to know how much data is going in/coming out and not passing through. Here are the rules I added: iptables -N ETH0_IN iptables -N ETH0_OUT iptables -I INPUT -i eth0 -j ETH0_IN iptables -I OUTPUT -o eth0 -j ETH0_OUT And here is a sample of the output: user@host:/tmp$ sudo iptables -x -vL -n Chain INPUT (policy ACCEPT 1549 packets, 225723 bytes) pkts bytes target prot opt in out source destination 199 54168 ETH0_IN all -- eth0 * 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 1417 packets, 178128 bytes) pkts bytes target prot opt in out source destination 201 19597 ETH0_OUT all -- * eth0 0.0.0.0/0 0.0.0.0/0 Chain ETH0_IN (1 references) pkts bytes target prot opt in out source destination Chain ETH0_OUT (1 references) pkts bytes target prot opt in out source destination As seen above, there are no packet and byte values for ETH0_IN and ETH0_OUT, which is not the same result in the tutorial I referenced. Is there a mistake that I made somewhere? Thanks for your time.

  Read the article

• Windows Server 2003 IPSec Tunnel Connected, But Not Working (Possibly NAT/RRAS Related)

  - by Kevinoid

  Configuration I have setup a "raw" IPSec tunnel between a Windows Server 2003 (SBS) machine and a Netgear FVG318 according to the instructions in Microsoft KB816514. The configuration is as follows (using the same conventions as the article): NetA | SBS2003 | FVG318 | NetB 10.0.0.0/24 | 216.x.x.x | 69.y.y.y | 10.0.254.0/24 Both the Main Mode and Quick Mode Security Associations are successfully completed and appear in the IP Security Monitor. I am also able to ping the SBS2003 server on its private address from any computer on NetB. The Problem Any traffic sent from a computer on NetA to NetB, or from SBS2003 to NetB (excluding ICMP Ping responses), is sent out on the public network interface outside the IPSec tunnel (no encryption or header authentication, as if the tunnel were not there). Pings sent from a computer on NetB to a computer on NetA successfully reach computers on NetA, but the responses are silently discarded by SBS2003 (they do not go out in the clear and do not generate any encrypted traffic). Possible Solutions Incorrect Configuration I could have mistyped something, somewhere, or KB816514 could be incorrect in some way. I have tried very hard to eliminate the first option. Have re-created the configuration several times, tried tweaking and adjusting all the settings I could without success (most prevent the SA from being established). NAT/RRAS I have seen multiple posts elsewhere suggesting that this could be due to interaction between NAT and the IPSec filters. Possibly the NetA private addresses get rewritten to 216.x.x.x before being compared with the Quick Mode IPSec filters and don't get tunneled because of the mismatch. In fact, The Cable Guy article from June 2005 "TCP/IP Packet Processing Paths" suggests that this is the case, (see step 2 and 4 of the Transit Traffic path). If this is the case, is there a way to exclude NetA-NetB traffic from NAT? Any thoughts, ideas, suggestions, and/or comments are appreciated.

  Read the article

• PC dies when running at 100% CPU

  - by user155631

  I recently wrote some Java code to generate images of the Mandelbrot set (fractal). I made use of the new Fork/Join facility in Java 7 to run separate threads on all four cores (2 real, 2 virtual)simultaneously, using a large number of iterations for greater accuracy. The problem is, the process runs fine for about a minute, and then it's as if someone has pulled the plug and the PC just dies. I thought it must be the CPUs overheating, so I ran Real Temp to monitor the temperature. It's an Intel i3 processor. I can see the temperature creeping up to 70 degrees, and then it seems to level off there and run for about another 30 seconds before dying. According to Real Temp, there's still a gap of 35 degrees between the actual temperature and TJ max. I also tried disabling "CPU TM function" in the BIOS, but the problem still occurs. A colleague suggested that it might be a power supply problem, so I borrowed a more powerful PSU (can't remember what wattage it was, but it's higher than mine which is 500W). The exact same thing still happens though. Is anyone able to suggest what the problem might be, or what I can try next?

  Read the article

• How does Firefox sync really work (when adding new devices)?

  - by tim11g

  I'm adding some less frequently used computers to my Firefox sync account. These computers were previously synced using Foxmarks BYOS. When I started using Firefox Sync, I deleted some old bookmarks. Later, as I added some other machines, old bookmarks (that still existed on the other machines) were synced back to my main machine. To prevent that from happening, I wonder if I perhaps need to delete all the bookmarks from new machines before adding them to the Sync account. But then I worry that it might sync the deletion of all the bookmarks and delete them all from the server and my other machines. Is there any documentation on the exact syncing behavior in the case of adding new devices? Is there any way to monitor progress and sync status? Is there any way to cause a "one way" sync for first time connection (sync server to browser only, overwriting everything in the browser? Is there any way to see a list of devices that are associated, and the last time they have synced? Thanks!

  Read the article

• How can I confirm that burn process is completed successfully??

  - by infant programmer

  Just now I tried to make a duplicate copy of my Windows XP Pro SP3 CD. I had set 32X speed while the max speed allowed is 48X. And checked "Verify the Data after burning". I didn't observe how much % did it complete. But after 15 mins (which is sufficient period to burn disc), I heard "Fatal Error" sound. When I saw the monitor, There was a message box which was showing "Error while burning Disc", I saved the error log which you can find here click_me. How do I acknowledge that burning process is done?? Well. I my PC is able to read the cd and it is bootable too.. I am not sure .. whether the burning process got failed or the verify Process! Please let me know if you have come across or aware of such situation .. As it is XP installation CD .. I don't want to do trial and error method. regards,

  Read the article

• Win 8.1 Hyper-v Full Screen and VPN problems

  - by tr0users

  I need to connect to my office using Cisco VPN software (RSA). Once connected all my internet traffic goes through the employer's VPN and this prevents me from listening to spotify. As a way around this I created a Win 2012 VM that I run in hyper-v from my Windows 8.1 Client. First I RDP to the VM, then I connect to the VPN. This forces the RDP session between my host laptop and the VM to close. I then open the hyper-v manager and double-click my VM to get a connection back (not great because I don't get the use of copy & paste this way). Previously when I opened my VM this way I would have full screen. I'm using a 1920x1080 monitor. Today when I re-open my connection to the VM it is displayed in a window that uses maybe 75% of the full screen. I have tried the menu option View\Full Screen Mode only centres the screen and apply black borders around the outside. Could anyone please suggest how I may solve the VPN or Full Screen problems? Thanks Rob.

  Read the article

• Proper approach to debug PC startup problems (POST)

  - by saurabhj

  My CPU was heating up to around 65 deg C and last time this had happened (about a year ago), I got thermal paste put between the CPU and heat sink and this managed to get it down to about 45 - 50 degrees. This time, I got some thermal paste and put it myself. However, my PC is not showing the POST display and not starting up. This is what happens LEDs light up HDDs spin Mouse is getting power All fans including the processor fan starts No display on monitor No diagnostic beep sounds (no sounds at all) What I have tried Removing everything including RAM, HDD, PCI cards, AGP card Boot up machine No changes from first state. What steps can I take to figure out where the problem lies? Note (might be important) When I removed the heat sink, the processor came out with it (it was stuck to it inspite of the processor latch on) Had to pry it separate with a screw-driver. Configuration Pentium 4, 2.8 Ghz with HT (very old, I know) Original Intel Mobo with onboard sound and graphics (GB series) 2x512 Mb DDR-RAM 2 SATA disks (320 Gigs / 250 gigs) DVD Writer Creative Sound Card Network card Any help would be appreciated. Thanks!

  Read the article

• Windows disk change monitoring for malware analysis

  - by SuperDuck

  Not sure if this question belongs to here, because it has some relations with 'serverfault' (system backups) and 'stackoverflow' (software analysis). I'm looking for a solution to monitor disk changes on a Windows system and selectively revert them. It should be able to handle live files like registry parts, so may need to be an offline backup software. It shouldn't silently pass over files which the current admin user doesn't have permissions on (files with no permission entries or owned by the 'system' user) Registry change tracking would be a bonus but is not a requirement I use virtual machines for malware analysis, there is even no solution to list file changes in disk snapshot files (delta VMDK). I currently use Ashampoo for monitoring changes. Though it's the best one between similars, it's not a good software and hasn't really evolved in many 'platinum', 'deluxe' versions released in the last 10 years (it even used non-resizable windows until the latest version). The real problem is it misses some disk / registry changes. Perhaps it only compares modification dates and doesn't catch a change if the dates are preserved. So, I think the solution should compare files using hashes, or file sizes at least. There are numerous backup software out there and I'm sure one can handle this, offline or online.

  Read the article

• DRBD as a block device for XEN VM (Centos 5.3)

  - by SaberTooth

  Hi all, I have setup a drbd resource between 2 server nodes - everything works correctly when doing sync tests between the two. (I want to create a HA cluster using drbd,xen and heartbeat) However, when I try and create a XEN VM with Centos as guest operating system, I get through to the partitioning screen on the install but when I select a partitioning type the next screen gives me the following error : "An error has occurred - no valid devices were found on which to create new file systems. Please check your hardware for the cause of this problem." This is the first time attempting create a setup like this and searching Google does not help much... my config files for DRBD and XEN.... DRBD (just the section that is pertinent) on xennode0 { device /dev/drbd0; disk /dev/sda5; address X.X.X.X:7788; flexible-meta-disk internal; } on xennode1 { device /dev/drbd0; disk /dev/sda5; address X.X.X.X:7788; meta-disk internal; } XEN kernel = "/boot/xeninstall/vmlinuz" ramdisk = "/boot/xeninstall/initrd.img" extra = "text" name = "VM" maxmem = 3000 memory = 3000 vcpus = 4 on_poweroff = "destroy" on_reboot = "restart" on_crash = "restart" vfb = [ ] disk = [ "phy:/dev/drbd0,sda1,w", "tap:aio:/srv/xen/xenswap.img,sda2,w" ] vif = [ "mac=00:16:3e:11:67:ae,bridge=xenbr0" ] root = "/dev/sda1 ro" Thanks in advance!

  Read the article

• Running .NET code in XML file [closed]

  - by Stuart McIntosh

  We have 2 servers, 1 already configured with .net which works fine and a new one which appears to be configured the same but when I open an xml page in Internet Explorer it complains about the <% tag. We have IIS on win srvr 2003 SP2. The website is configured with .NET 1.1.4322. In ISAPI extensions have set the .XML extension to use c:\windows\microsoft.net\framework\v1.1.4322\aspnet_isapi.dll But the page: <property name="documentmaxage" value="0"/> <property name="documentmaxstale" value="0"/> <var name="m_Prompt_Path" /> <form id="InitVoiceXmlDoc"> <block> <assign name="m_Prompt_Path" expr="&quot;<% Response.Write(Request.QueryString["m_Prompt_Path"]); %>&quot;"/> </block> </form> gives the error: The XML page cannot be displayed Cannot view XML input using XSL style sheet. Please correct the error and then click the Refresh button, or try again later. The character '<' cannot be used in an attribute value. Error processing resource 'http://localhost:11119/fails.xml'. Lin... &quo... We have the same config on another server which works fine. So are there other options apart from the ISAPI extensions that I need to look at

  Read the article

• Extend Linux Desktop to another X Windows Display

  - by unknown (google)

  Hello, I am a long time Linux user of the Xinerama and other technologies for extending a desktop to multiple monitors. However when I travel with my laptop I miss the multi-monitor support I enjoy at home. Recently I acquired a second laptop for a low price. Both laptops are running Fedora (versions 10 and 11 respectively). I use Gnome as my primary desktop environment. I know about synergy. I use synergy all the time to control the screen of other Windows / Linux systems I use. I would like to know, can I sit both my primary and secondary laptops together and achieve a Xinerama-like extended desktop environment? Ideally I would like to start a GNOME session on my primary laptop. And then start a X-Windows Desktop on my secondary laptop and extend my primary laptop's desktop onto it. I would like to be able to move Windows from the primary desktop to the secondary laptop desktop. Would I need to use synergy to do this with some other bit of X-Windows technology? Or is there X-Windows technology that will do all this for me? I am familiar with X Windows ability to display applications remotely. I am also familiar with Nomachine's NoX.

  Read the article

• Measuring performance indicators on a cluster

  - by Aditya Singh

  My architecture is based on Amazon. A ELB load balancer balances POST requests among m1.large instances. Every instance has a nginx server on port 80 which distributes the requests to 4 python-tornado servers on backend which handle the request. These tornado servers are taking about 5 - 10ms to respond to one request but this is the internal compute time of every request. I want to put this thing on test and i want to measure the response time from ELB to upstream and back and how does it vary when the QPS throughput is increased and plot a graph of Time vs. QPS vs. Latency and other factors like CPU and Memory. Is there a software to do that or should i log everything somewhere with latency checks and then analyze the whole log to get the stuff out. I would also need to write a self-monitor which keeps checking the whole response time. Is it possible to do it with a script from within the server. If so, will it be accurate ?

  Read the article

• Half of installed RAM is hardware reserved

  - by user968270

  After a rather arduous and convoluted series of problems that left me without a desktop for ~80 days, I've finally got the thing up and running, having replaced the power supply, motherboard, graphics card and CPU. Now, however, I'm experiencing the 'hardware reserved RAM' issue. Perhaps this is the exhaustion talking, but looking at the question that tends to get pointed to when this kind of topic gets locked as a duplicate hasn't helped. I have 16 GB of RAM installed in an MSi 970A-G46, which is spec'd for up to 32 GB of RAM. The BIOS recognizes that I have 16 GB installed, and the resource monitor also shows the whole 16 GB, only it shows 8 GB as hardware reserved. I've seen suggestions that it's an OS issue, but the particular installation of Windows 7 (64-bit) which I'm running on my boot drive is the same as the one that could actually access the 16 GB in my previous motherboard (MSi 870A-G54). I've updated my BIOS using the MSi Live Update tool and restarted the machine with no effect, and I cannot seem to locate any 'Memory Remapping' option as I've seen mentioned. I've physically swapped the RAM between the slots to no effect. I've unchecked the Maximum Memory box in the msconfig Boot tab's advanced options, also to no effect. These are my system's basic specifications OS: Windows 7 Home Premium (64-Bit) Motherboard: MSi 970A-G46 CPU: AMD FX-8150 Graphics Card: XFX Radeon HD 6870 Boot Drive: OCZ Agility 3 Storage Drive: Samsung Spinpoint F3 ST1000DM005/HD103SJ 1TB PSU: Thermaltake TR-2 TR600 600W ATX12V v2.3

  Read the article

< Previous Page | 367 368 369 370 371 372 373 374 375 376 377 378  | Next Page >