Search Results

Search found 10245 results on 410 pages for 'quick guide to irm'.

Page 372/410 | < Previous Page | 368 369 370 371 372 373 374 375 376 377 378 379  | Next Page >

• Issue in setting up VPN connection (IKEv1) using android (ICS vpn client) with Strongswan 4.5.0 server

  - by Kushagra Bhatnagar

  I am facing issues in setting up VPN connection(IKEv1) using android (ICS vpn client) and Strongswan 4.5.0 server. Below is the set up: Strongswan server is running on ubuntu linux machine which is connected to some wifi hotspot. Using the steps in this guide link, I generated CA, server and client certificate. Once certificates are generated, following (clientCert.p12 and caCert.pem) are sent to mobile via mail and installed on android device. Below are the ip addresses assigned to various interfaces Linux server wlan0 interface ip where server is running: 192.168.43.212, android device eth0 interface ip address: 192.168.43.62; Android device is also attached with the same wifi hotspot. On the Android device, I uses IPsec Xauth RSA option for setting up VPN authentication configuration. I am using the following ipsec.conf configuration: # basic configuration config setup plutodebug=all # crlcheckinterval=600 # strictcrlpolicy=yes # cachecrls=yes nat_traversal=yes # charonstart=yes plutostart=yes # Add connections here. # Sample VPN connections conn ios1 keyexchange=ikev1 authby=xauthrsasig xauth=server left=%defaultroute leftsubnet=0.0.0.0/0 leftfirewall=yes leftcert=serverCert.pem right=192.168.43.62 rightsubnet=10.0.0.0/24 rightsourceip=10.0.0.2 rightcert=clientCert.pem pfs=no auto=add      With the above configurations when I enable VPN on android device, VPN connection is not successful and it gets timed out in Authentication phase. I ran wireshark on both the android device and strongswan server, from the tcpdump below are the observations. Initially Identity Protection (Main mode) exchanges happens between device and server and all are successful. After all successful Identity Protection (Main mode) exchanges server is sending Transaction (Config mode) to device. In reply android device is sending Informational message instead of Transaction (Config mode) message. Further server is keep on sending Transaction (Config mode) message and device is again sending Identity Protection (Main mode) messages. Finally timeout happens and connection fails. I also capture Strongswan server logs and below are the snippets from the server logs which also verifies the same(described above). Apr 27 21:09:40 Linux pluto[12105]: | **parse ISAKMP Message: Apr 27 21:09:40 Linux pluto[12105]: | initiator cookie: Apr 27 21:09:40 Linux pluto[12105]: | 06 fd 61 b8 86 82 df ed Apr 27 21:09:40 Linux pluto[12105]: | responder cookie: Apr 27 21:09:40 Linux pluto[12105]: | 73 7a af 76 74 f0 39 8b Apr 27 21:09:40 Linux pluto[12105]: | next payload type: ISAKMP_NEXT_HASH Apr 27 21:09:40 Linux pluto[12105]: | ISAKMP version: ISAKMP Version 1.0 Apr 27 21:09:40 Linux pluto[12105]: | exchange type: ISAKMP_XCHG_INFO Apr 27 21:09:40 Linux pluto[12105]: | flags: ISAKMP_FLAG_ENCRYPTION Apr 27 21:09:40 Linux pluto[12105]: | message ID: a2 80 ad 82 Apr 27 21:09:40 Linux pluto[12105]: | length: 92 Apr 27 21:09:40 Linux pluto[12105]: | ICOOKIE: 06 fd 61 b8 86 82 df ed Apr 27 21:09:40 Linux pluto[12105]: | RCOOKIE: 73 7a af 76 74 f0 39 8b Apr 27 21:09:40 Linux pluto[12105]: | peer: c0 a8 2b 3e Apr 27 21:09:40 Linux pluto[12105]: | state hash entry 25 Apr 27 21:09:40 Linux pluto[12105]: | state object not found Apr 27 21:09:40 Linux pluto[12105]: packet from 192.168.43.62:500: Informational Exchange is for an unknown (expired?) SA Apr 27 21:09:40 Linux pluto[12105]: | next event EVENT_RETRANSMIT in 10 seconds for #9 Can anyone please provide update on this issue. Why the VPN connection gets timed out and why the ISAKMP exchanges are not proper between Android and strongswan server.

  Read the article

• DNS lookups failing somewhere between firewall and router

  - by TessellatingHeckler

  we have a setup of ADSL line - Cisco 837 ADSL router - Zyxel ZyWall 35 firewall/NAT - Switch == Intel load balanced NICS in a server. It has been fine for years, suddenly DNS resolution stopped working on the server. No changes that I know of, so I can't work backwards from there. It was configured with the ISP's DNS servers, neither network device does DNS relaying. Wireshark shows the request go out but nothing comes back. The server networking stack seems OK though, because if we query an internal DNS server on a remote site, that works. I can logon to the Cisco, and DNS resolves OK from the command line. I can logon to the ZyWall, and DNS does not resolve from the command line. So the problem seems to be the firewall, patch cable or router, yes? On the router: interface Ethernet0 ip address aaa.bbb.ccc.ddd 255.255.255.ddd ip tcp adjust-mss 1450 hold-queue 100 out On the firewall: DNS server set to 8.8.8.8 (Google's), DNS traffic allowed LAN-WAN. What else should I look for? Update: Following This guide I've got traffic logging on the Cisco. I have also got access to a public DNS server which I can run tcpdump on to see things from the other side. And as per the below comments, I've tested with Dig and see that DNS over TCP works, and over UDP does not. Currently: DNS request from the server using TCP shows up in the firewall log, and in the Cisco log, and in tcpdump on the DNS server, the answer comes back, it works fine. DNS request from the server using UDP shows up in the firewall log, and in the Cisco log, does NOT show in tcpdump on the DNS server, times out. DNS request from the cisco (using UDP) does show up in tcpdump on the DNS server, answer received, works fine. Ping requests from the server and the cisco to the DNS server show up in tcpdump on the DNS server. DNS request from the server using UDP does show up on the firewall. Summary: TCP seems fine throughought. UDP works over the ADSL and to the Cisco, and it works from the server to the Cisco, but it doesn't cross the Cisco properly, it seems. I did see the Cisco showing as connected at 10Mb/full-duplex internally, and the firewall showing as 100Mb/full-duplex externally. I have forced the firewall to 10Mb and rebooted both devices. That seemed to help get UDP traffic (server-firewall-cisco) instead of (server-firewall), but did not fix it. Update: Sanitized Cisco config: version 12.2 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname cisco ! logging queue-limit 100 enable secret 5 {password} enable password 7 {password} ! ip subnet-zero ip domain name example.org ip name-server {nameserver_IP} ! ! ip audit notify log ip audit po max-events 100 no ftp-server write-enable ! interface Ethernet0 ip address {Inside_public_IP} 255.255.255.248 ip tcp adjust-mss 1460 hold-queue 100 out ! interface ATM0 no ip address no atm ilmi-keepalive pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 ! dsl operating-mode auto ! interface Dialer1 ip unnumbered Ethernet0 encapsulation ppp dialer pool 1 dialer idle-timeout 0 dialer persistent no cdp enable ppp chap hostname {ADSL_Username} ppp chap password 7 {ADSL_Password} ! ip classless ip route 0.0.0.0 0.0.0.0 Dialer1 no ip http server no ip http secure-server ! access-list 23 permit {IP} dialer-list 1 protocol ip permit no cdp run snmp-server enable traps tty ! {con, vty} end

  Read the article

• fail2ban custom action to permanent ban IPs from China

  - by John Magnolia

  When a IP address gets banned how can I check if the banned IP address is from China. If yes, then add it to the permanent ban list. I have found this nice guide which write the banned IP to file. Reason: I am getting a lot of brute force attacks from China daily, thankfully fail2ban is helping restrict this although they appear to be getting worse and they are just changing their IP Address. Or even better would be if there was a maintained database of known hacker IP addresses. Example 1 Hi, The IP 60.169.78.77 has just been banned by Fail2Ban after 4 attempts against vsftpd. Here are more information about 60.169.78.77: % [whois.apnic.net node-7] % Whois data copyright terms http://www.apnic.net/db/dbcopyright.html inetnum: 60.166.0.0 - 60.175.255.255 netname: CHINANET-AH descr: CHINANET anhui province network descr: China Telecom descr: A12,Xin-Jie-Kou-Wai Street descr: Beijing 100088 country: CN admin-c: CH93-AP tech-c: JW89-AP mnt-by: APNIC-HM mnt-routes: MAINT-CHINANET-AH mnt-lower: MAINT-CHINANET-AH status: ALLOCATED PORTABLE changed: [email protected] 20040721 source: APNIC person: Chinanet Hostmaster nic-hdl: CH93-AP e-mail: [email protected] address: No.31 ,jingrong street,beijing address: 100032 phone: +86-10-58501724 fax-no: +86-10-58501724 country: CN changed: [email protected] 20070416 mnt-by: MAINT-CHINANET source: APNIC person: Jinneng Wang address: 17/F, Postal Building No.120 Changjiang address: Middle Road, Hefei, Anhui, China country: CN phone: +86-551-2659073 fax-no: +86-551-2659287 e-mail: [email protected] nic-hdl: JW89-AP mnt-by: MAINT-NEW changed: [email protected] 19990818 source: APNIC Regards, Fail2Ban Example 2 Hi, The IP 60.169.78.81 has just been banned by Fail2Ban after 4 attempts against vsftpd. Here are more information about 60.169.78.81: % [whois.apnic.net node-6] % Whois data copyright terms http://www.apnic.net/db/dbcopyright.html inetnum: 60.166.0.0 - 60.175.255.255 netname: CHINANET-AH descr: CHINANET anhui province network descr: China Telecom descr: A12,Xin-Jie-Kou-Wai Street descr: Beijing 100088 country: CN admin-c: CH93-AP tech-c: JW89-AP mnt-by: APNIC-HM mnt-routes: MAINT-CHINANET-AH mnt-lower: MAINT-CHINANET-AH status: ALLOCATED PORTABLE changed: [email protected] 20040721 source: APNIC person: Chinanet Hostmaster nic-hdl: CH93-AP e-mail: [email protected] address: No.31 ,jingrong street,beijing address: 100032 phone: +86-10-58501724 fax-no: +86-10-58501724 country: CN changed: [email protected] 20070416 mnt-by: MAINT-CHINANET source: APNIC person: Jinneng Wang address: 17/F, Postal Building No.120 Changjiang address: Middle Road, Hefei, Anhui, China country: CN phone: +86-551-2659073 fax-no: +86-551-2659287 e-mail: [email protected] nic-hdl: JW89-AP mnt-by: MAINT-NEW changed: [email protected] 19990818 source: APNIC Regards, Fail2Ban Example 3 Hi, The IP 222.133.244.99 has just been banned by Fail2Ban after 4 attempts against vsftpd. Here are more information about 222.133.244.99: % [whois.apnic.net node-6] % Whois data copyright terms http://www.apnic.net/db/dbcopyright.html inetnum: 222.133.244.96 - 222.133.244.127 netname: LCZFFHQ country: CN descr: liaochenggovermentfanghuoqiang admin-c: DS95-AP tech-c: DS95-AP status: ASSIGNED NON-PORTABLE changed: [email protected] 20060122 mnt-by: MAINT-CNCGROUP-SD source: APNIC route: 222.132.0.0/14 descr: CNC Group CHINA169 Shandong Province Network country: CN origin: AS4837 mnt-by: MAINT-CNCGROUP-RR changed: [email protected] 20060118 source: APNIC person: Data Communication Bureau Shandong nic-hdl: DS95-AP e-mail: [email protected] address: No.77 Jingsan Road,Jinan,Shandong,P.R.China phone: +86-531-6052611 fax-no: +86-531-6052414 country: CN changed: [email protected] 20050330 mnt-by: MAINT-CNCGROUP-SD source: APNIC Regards, Fail2Ban

  Read the article

• What would make a noise in a PC on graphics operations on a passively-cooled system?

  - by T.J. Crowder

  I have this system based on the Intel D510MO motherboard, which is basically an Atom D510 (dual-core HT Atom w/built-in GPU), an Intel NM10 chipset, and a Realtek Gigabit LAN controller. It's entirely passively cooled. I noticed almost immediately that there was a kind of very, very soft noise that corresponded with graphics operations, sort of the noise you'd get if you had a sheet of flat paper and slid something really light across it — but more electronic than that. I wrote it off as observation error and/or disk activity triggered by the graphics operation (although the latter seemed like a lot of unnecessary disk activity). It isn't. I got curious enough that I finally did a few controlled experiments, and here's what I've determined: It isn't the HDD. For one thing, the sounds the HDD makes (when seeking, when reading or writing, when just sitting there spinning) is different. For another, I used sudo hdparm -y /dev/sda (I'm using Ubuntu 10.04 LTS) to temporarily put the disk on standby while making sure that non-disk graphics op was happening in a loop. The disk spun down, but the other sound continued, corresponding perfectly with the timing of the graphics op. (Then the disk spun up again, but it takes long enough that I could rule out the HDD.) It isn't the monitor; I ensured the two were well physically-separated and the sound was definitely coming from the main box. It isn't something else in the room; the sound is coming from the box. It isn't cross-talk to an audio circuit coming out the speakers. (It doesn't have any speakers.) It isn't my mouse (e.g., when I'm trying to make graphics ops happen); the sound happens if I set up a recurring operation and don't use the mouse at all, or if I lift the mouse off the table slightly (but enough that the laser still registers movement). It isn't the voices in my head; they never whisper like that. Other observations: It doesn't seem to matter what the graphics operation is; anything that changes what's on the screen seems to do it. I get the sound when moving the mouse over the Chromium tab bar (which makes the tab backgrounds change); I get it when a web page has a counter on it that changes the text on the page: I get it when dragging window contents around. The sound is very, very slightly louder if the graphics op is larger, like scrolling a text area when writing a question on superuser.com, than for smaller operations like the tick counter on the web page. But it's very slight. It's fairly loud (and of good duration) when the op involves color changes to substantial surface areas. For instance, when asking a question here on superuser and you move the cursor between the question box and the tag box, and the help to the right fades out, changes, and fades back in. (Yet another example related to the web browser, so let me say: I hear it when operations completely unrelated to the web browser as well.) It doesn't sound like arcing or anything like that (I'd've shut off the machine Right Quick Like if it did). Moving windows does it. Scrolling windows (by and large) doesn't. I have the feeling I've heard this sort of thing before, when all system fans were on low and such, with other systems — but (again) written it off as observational error. For all the world it's like I'm hearing the CPU working (as opposed to the GPU; note the window scroll thing above) or data being transferred somewhere, but that just seems...unlikely. So what am I hearing? This may seem like a very localized question, but perhaps other silent PC enthusiasts may be interested as well...

  Read the article

• Facing issues in setting up VPN connection(IKEv1) using iphone (Defult Cisco VPN client) and Strongswan 4.5.0 server

  - by Kushagra Bhatnagar

  I am facing issues in setting up VPN connection(IKEv1) using iPhone (Defult Cisco VPN client) and Strongswan 4.5.0 server. The Strongswan server is running on Ubuntu Linux, which is connected to some wifi hotspot. This is the guide which was used. I generated CA, server and client certificate, with the only difference mentioned below. “While generating server certificate, as per link CN=vpn.strongswan.org instead of this I changed CN name to CN=192.168.43.212.” Once certificates are generated, following (clientCert.p12 and caCert.pem) are sent to mobile via mail and installed on iphone. After installation I notice that certificates are considered as trusted also. Below are the ip addresses assigned to various interfaces Linux server wlan0 interface ip where server is running: 192.168.43.212 Iphone eth0 interface ip address: 192.168.43.72. iphone is also attached with the same wifi hotspot. Below is the snapshot of client configurations. Description Strong swan Server 192.168.43.212 Account ipsecvpn Password ***** Use certificate ON Certificate client The above username and password are in sync with the ipsec.secrets file. I am using the following ipsec.conf configuration: # basic configuration config setup plutodebug=all # crlcheckinterval=600 # strictcrlpolicy=yes # cachecrls=yes nat_traversal=yes # charonstart=yes plutostart=yes # Add connections here. # Sample VPN connections conn ios1 keyexchange=ikev1 authby=xauthrsasig xauth=server left=%defaultroute leftsubnet=0.0.0.0/0 leftfirewall=yes leftcert=serverCert.pem right=192.168.43.72 rightsubnet=10.0.0.0/24 rightsourceip=10.0.0.2 rightcert=clientCert.pem pfs=no auto=add With the above configurations when I enable VPN on iphone, it says Could not able to verify server certificate. I ran Wireshark on a Linux server and observe that initially some ISAKMP message exchanges happens between client and server, which are successful but before authorization, client is sending some informational message and soon after this client is showing error as popup Could not able to verify server certificate. Capture logs on Strongswan server and in server logs below errors are observed: From auth.log Apr 25 20:16:08 Linux pluto[4025]: | ISAKMP version: ISAKMP Version 1.0 Apr 25 20:16:08 Linux pluto[4025]: | exchange type: ISAKMP_XCHG_INFO Apr 25 20:16:08 Linux pluto[4025]: | flags: ISAKMP_FLAG_ENCRYPTION Apr 25 20:16:08 Linux pluto[4025]: | message ID: 9d 1a ea 4d Apr 25 20:16:08 Linux pluto[4025]: | length: 76 Apr 25 20:16:08 Linux pluto[4025]: | ICOOKIE: f6 b7 06 b2 b1 84 5b 93 Apr 25 20:16:08 Linux pluto[4025]: | RCOOKIE: 86 92 a0 c2 a6 2f ac be Apr 25 20:16:08 Linux pluto[4025]: | peer: c0 a8 2b 48 Apr 25 20:16:08 Linux pluto[4025]: | state hash entry 8 Apr 25 20:16:08 Linux pluto[4025]: | state object not found Apr 25 20:16:08 Linux pluto[4025]: **packet from 192.168.43.72:500: Informational Exchange is for an unknown (expired?) SA** Apr 25 20:16:08 Linux pluto[4025]: | next event EVENT_RETRANSMIT in 8 seconds for #8 Apr 25 20:16:16 Linux pluto[4025]: | Apr 25 20:16:16 Linux pluto[4025]: | *time to handle event Apr 25 20:16:16 Linux pluto[4025]: | event after this is EVENT_RETRANSMIT in 2 seconds Apr 25 20:16:16 Linux pluto[4025]: | handling event EVENT_RETRANSMIT for 192.168.43.72 "ios1" #8 Apr 25 20:16:16 Linux pluto[4025]: | sending 76 bytes for EVENT_RETRANSMIT through wlan0 to 192.168.43.72:500: Apr 25 20:16:16 Linux pluto[4025]: | a6 a5 86 41 4b fb ff 99 c9 18 34 61 01 7b f1 d9 Apr 25 20:16:16 Linux pluto[4025]: | 08 10 06 01 e9 1c ea 60 00 00 00 4c ba 7d c8 08 Apr 25 20:16:16 Linux pluto[4025]: | 13 47 95 18 19 31 45 30 2e 22 f9 4d 85 2c 27 bc Apr 25 20:16:16 Linux pluto[4025]: | 9e 9b e1 ae 1e 35 51 6f ab 80 f5 73 3c 15 8d 20 Apr 25 20:16:16 Linux pluto[4025]: | 4b 46 47 86 50 24 3f 13 15 7d d5 17 Apr 25 20:16:16 Linux pluto[4025]: | inserting event EVENT_RETRANSMIT, timeout in 40 seconds for #8 Apr 25 20:16:16 Linux pluto[4025]: | next event EVENT_RETRANSMIT in 2 seconds for #10 Apr 25 20:16:16 Linux pluto[4025]: | rejected packet: Apr 25 20:16:16 Linux pluto[4025]: | Apr 25 20:16:16 Linux pluto[4025]: | control: Apr 25 20:16:16 Linux pluto[4025]: | 30 00 00 00 00 00 00 00 00 00 00 00 0b 00 00 00 Apr 25 20:16:16 Linux pluto[4025]: | 6f 00 00 00 02 03 03 00 00 00 00 00 00 00 00 00 Apr 25 20:16:16 Linux pluto[4025]: | 02 00 00 00 c0 a8 2b 48 00 00 00 00 00 00 00 00 Apr 25 20:16:16 Linux pluto[4025]: | name: Apr 25 20:16:16 Linux pluto[4025]: | 02 00 01 f4 c0 a8 2b 48 00 00 00 00 00 00 00 00 Apr 25 20:16:16 Linux pluto[4025]: **ERROR: asynchronous network error report on wlan0 for message to 192.168.43.72 port 500, complainant 192.168.43.72: Connection refused [errno 111, origin ICMP type 3 code 3 (not authenticated)]** Anybody please provide some update about this error and how to solve this issue.

  Read the article

• How to save POST&GET headers of a web page with "Wireshark"?

  - by brilliant

  Hello everybody, I've been trying to find a python code that would log in to my mail box on yahoo.com from "Google App Engine". I was given this code: import urllib, urllib2, cookielib url = "https://login.yahoo.com/config/login?" form_data = {'login' : 'my-login-here', 'passwd' : 'my-password-here'} jar = cookielib.CookieJar() opener = urllib2.build_opener(urllib2.HTTPCookieProcessor(jar)) form_data = urllib.urlencode(form_data) # data returned from this pages contains redirection resp = opener.open(url, form_data) # yahoo redirects to http://my.yahoo.com, so lets go there instead resp = opener.open('http://mail.yahoo.com') print resp.read() The author of this script looked into HTML script of yahoo log-in form and came up with this script. That log-in form contains two fields, one for users' Yahoo! ID and another one is for users' password. However, when I tried this code out (substituting mu real Yahoo login for 'my-login-here' and my real password for 'my-password-here'), it just return the log-in form back to me, which means that something didn't work right. Another supporter suggested that I should send an MD5 hash of my password, rather than a plain password. He also noted that in that log-in form there are a lot other hidden fields besides login and password fields (he called them "CSRF protections") that I would also have to deal with: <input type="hidden" name=".tries" value="1"> <input type="hidden" name=".src" value="ym"> <input type="hidden" name=".md5" value=""> <input type="hidden" name=".hash" value=""> <input type="hidden" name=".js" value=""> <input type="hidden" name=".last" value=""> <input type="hidden" name="promo" value=""> <input type="hidden" name=".intl" value="us"> <input type="hidden" name=".bypass" value=""> <input type="hidden" name=".partner" value=""> <input type="hidden" name=".u" value="bd5tdpd5rf2pg"> <input type="hidden" name=".v" value="0"> <input type="hidden" name=".challenge" value="5qUiIPGVFzRZ2BHhvtdGXoehfiOj"> <input type="hidden" name=".yplus" value=""> <input type="hidden" name=".emailCode" value=""> <input type="hidden" name="pkg" value=""> <input type="hidden" name="stepid" value=""> <input type="hidden" name=".ev" value=""> <input type="hidden" name="hasMsgr" value="0"> <input type="hidden" name=".chkP" value="Y"> <input type="hidden" name=".done" value="http://mail.yahoo.com"> He said that I should do the following: Simulate normal login and save login page that I get; Save POST&GET headers with "Wireshark"; Compare login page with those headers and see what fields I need to include with my request; I really don't know how to carry out the first two of these three steps. I have just downloaded "Wireshark" and have tried capturing some packets there. However, I don't know how to "simulate normal login and save the login page". Also, I don't how to save POST$GET headers with "Wireshark". Can anyone, please, guide me through these two steps in "Wireshark"? Or at least tell me what I should start with. Thank You.

  Read the article

• COPSSH RSA only authentication connection problem

  - by Siriss

  Hello all- I am trying to setup an RSA Authentication only SSH/SFTP server. The SSH will be used primarily for RDC. Everything works just fine if I use password authentication. I am using Putty Key Generator to create he keys and I have pasted the key into authorized_keys file and restarted the OpenSSH server. I am using FileZilla to test the SFTP connection as that is the most important. For my tests I have created the keys without password correction. It will not work with a standard SSH connection either. It says "Server refused our key". I have recreated the key twice double checking with a guide on google, and I am pretty sure I did it correctly. I load the key file into FileZilla under settings/SFTP and try to connect and I get the following error: Disconnected: No supported authentication methods available. I have been playing with the different settings all night and I cannot figure it out. Here is my sshd_config file: # $OpenBSD: sshd_config,v 1.80 2008/07/02 02:24:18 djm Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/usr/bin:/bin:/usr/sbin:/sbin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. #Port 22 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # Disable legacy (protocol version 1) support in the server for new # installations. In future the default will change to require explicit # activation of protocol 1 Protocol 2 # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh/ssh_host_rsa_key #HostKey /etc/ssh/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 1024 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH #LogLevel INFO # Authentication: #LoginGraceTime 2m PermitRootLogin no #StrictModes yes #MaxAuthTries 6 #MaxSessions 10 RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh/ssh_known_hosts RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! PasswordAuthentication no PermitEmptyPasswords no # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no #GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication and # PasswordAuthentication. Depending on your PAM configuration, # PAM authentication via ChallengeResponseAuthentication may bypass # the setting of "PermitRootLogin without-password". # If you just want the PAM account and session checks to run without # PAM authentication, then enable this but set PasswordAuthentication # and ChallengeResponseAuthentication to 'no'. UsePAM no #AllowAgentForwarding yes #AllowTcpForwarding yes #GatewayPorts no #X11Forwarding no #X11DisplayOffset 10 #X11UseLocalhost yes #PrintMotd yes #PrintLastLog yes #TCPKeepAlive yes UseLogin no #UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner none # override default of no subsystems Subsystem sftp /bin/sftp-server # Example of overriding settings on a per-user basis #Match User anoncvs # X11Forwarding no # AllowTcpForwarding no # ForceCommand cvs server Thank you so much for your help!

  Read the article

• Performance issues when using SSD for a developer notebook (WAMP/LAMP stack)?

  - by András Szepesházi

  I'm a web application developer using my notebook as a standalone development environment (WAMP stack). I just switched from a Core2-duo Vista 32 bit notebook with 2Gb RAM and SATA HDD, to an i5-2520M Win7 64 bit with 4Gb RAM and 128 GB SDD (Corsair P3 128). My initial experience was what I expected, fast boot, quick load of all the applications (Eclipse takes now 5 seconds as opposed to 30s on my old notebook), overall great experience. Then I started to build up my development stack, both as LAMP (using VirtualBox with a debian guest) and WAMP (windows native apache + mysql + php). I wanted to compare those two. This still all worked great out, then I started to pull in my projects to these stacks. And here came the nasty surprise, one of those projects produced a lot worse response times than on my old notebook (that was true for both the VirtualBox and WAMP stack). Apache, php and mysql configurations were practically identical in all environments. I started to do a lot of benchmarking and profiling, and here is what I've found: All general benchmarks (Performance Test 7.0, HDTune Pro, wPrime2 and some more) gave a big advantage to the new notebook. Nothing surprising here. Disc specific tests showed that read/write operations peaked around 380M/160M for the SSD, and all the different sized block operations also performed very well. Started apache performance benchmarking with Apache Benchmark for a small static html file (10 concurrent threads, 500 iterations). Old notebook: min 47ms, median 111ms, max 156ms New WAMP stack: min 71ms, median 135ms, max 296ms New LAMP stack (in VirtualBox): min 6ms, median 46ms, max 175ms Right here I don't get why the native WAMP stack performed so bad, but at least the LAMP environment brought the expected speed. Apache performance measurement for non-cached php content. The php runs a loop of 1000 and generates sha1(uniqid()) inisde. Again, 10 concurrent threads, 500 iterations were used for the benchmark. Old notebook: min 0ms, median 39ms, max 218ms New WAMP stack: min 20ms, median 61ms, max 186ms New LAMP stack (in VirtualBox): min 124ms, median 704ms, max 2463ms What the hell? The new LAMP performed miserably, and even the new native WAMP was outperformed by the old notebook. php + mysql test. The test consists of connecting to a database and reading a single record form a table using INNER JOIN on 3 more (indexed) tables, repeated 100 times within a loop. Databases were identical. 10 concurrent threads, 100 iterations were used for the benchmark. Old notebook: min 1201ms, median 1734ms, max 3728ms New WAMP stack: min 367ms, median 675ms, max 1893ms New LAMP stack (in VirtualBox): min 1410ms, median 3659ms, max 5045ms And the same test with concurrency set to 1 (instead of 10): Old notebook: min 1201ms, median 1261ms, max 1357ms New WAMP stack: min 399ms, median 483ms, max 539ms New LAMP stack (in VirtualBox): min 285ms, median 348ms, max 444ms Strictly for my purposes, as I'm using a self contained development environment (= low concurrency) I could be satisfied with the second test's result. Though I have no idea why the VirtualBox environment performed so bad with higher concurrency. Finally I performed a test of including many php files. The application that I mentioned at the beginning, the one that was performing so bad, has a heavy bootstrap, loads hundreds of small library and configuration files while initializing. So this test does nothing else just includes about 100 files. Concurrency set to 1, 100 iterations: Old notebook: min 140ms, median 168ms, max 406ms New WAMP stack: min 434ms, median 488ms, max 604ms New LAMP stack (in VirtualBox): min 413ms, median 1040ms, max 1921ms Even if I consider that VirtualBox reached those files via shared folders, and that slows things down a bit, I still don't see how could the old notebook outperform so heavily both new configurations. And I think this is the real root of the slow performance, as the application uses even more includes, and the whole bootstrap will occur several times within a page request (for each ajax call, for example). To sum it up, here I am with a brand new high-performance notebook that loads the same page in 20 seconds, that my old notebook can do in 5-7 seconds. Needless to say, I'm not a very happy person right now. Why do you think I experience these poor performance values? What are my options to remedy this situation?

  Read the article

• moving raid 10 to another identical server both on Smart Array 6i controllers

  - by SalimQrdl

  I have dead HP DL 380G4 with RAID 1+0 with 1 logical volume from 4x72GB drives on built-in Smart Array 6i 128Mb BBWC. It was shut down properly. It seems it was usual death for Proliant with ILO led 2,3,8 lighting. I want to move array to another identical server with same raid firmware level. What is the best strategy?: I have RAID 1+0 on bay 0 bay 1 bay 2 bay 3 As I understand bay0+bay1 are in RAID 1 , bay2+bay3 are in RAID 1, and both RAID 1 pairs are in RAID 0. So should I : Clear RAID config on new server, insert bay 0, bay 2 and power-on or Create RAID 1+0 with 1 logical volume from clear HDDs , and then poweroff ,remove HDDs and insert 2 HDDs(bay 0, bay 2) from old RAID 1+0. then power-on. (each hdd has its raid position info stored but may be could work on same config) According to documentation for Smart Array 6i it could be possible to migrate. however one requirement point is unclear for me Before you move drives, the following conditions must be met: • The array is in its original configuration. " What is orginal and non-original config for RAID 1+0? Another point "If you want to move an array to another controller, you must also consider the following additional limitations: • All drives in the array must be moved at the same time." I want to move one hdd from each RAID 1 pair. to have mirrors untouched just in case. Do they mean to move all 4 simultaniously? Smart Array 6i User Guide: Moving Drives and Arrays You can move drives to other ID positionson the same array controller. You can also move a complete arrayfrom one controller to another, even if the controllers are on different servers. Before you move drives, the following conditions must be met: • If moving thedrives to a different server, the new server must have enough empty bays to accommodate all the drives simultaneously. • The move will not result in more than 14 physical drives per controller channel. • No controller will be configured with more than 32 logical volumes. • The array has no failed or missing drives. • The array is in its original configuration. • The controller is not reading from or writing to any of the spare drives in the array. • The controller is not running capacity expansion, capacity extension, or RAID or stripe size migration. • The controller is using the latestfirmware version (recommended). If you want to move an array to another controller, you must also consider the following additional limitations: • All drives in the array must be moved at the same time. • In most cases, a moved array (and the logical drives that it contains) can still undergo arraycapacity expansion, logical drive capacity extension, or migration of RAID level orstripe size. When all the conditions have been met: Back up all data before removing any drives or changing configuration. This step is requiredif you are moving data-containing drives from a controller that does not have a battery-backed cache. Power down the system. If you are moving an array from a controller that contains a RAID ADG logical volume to a controller that does not support RAID ADG: Move the drives. Power up the system. If a 1724 POST message is displayed, drive positions were changed successfully and the configuration was updated. If a 1785 (NotConfigured)POST message is displayed: a. Power down the system immediately to prevent data loss. b. Return the drives to their original locations. c. Restore the data from backup, if necessary. Check the new drive configuration byrunning ORCA or ACU ("Configuring an Array" on page 9).

  Read the article

• How can I work around problems with certificate configuration in Remote Desktop Services?

  - by Michael Steele

  I am setting up a Remote Desktop Services farm, and am having trouble configuring certificates for it to use. A demonstration of the problem I'm seeing can be found in Step #4. At this point I am convinced that there are problems with the user interface, and am looking for ways around them. Is there any way to configure certificates in Remote Desktop Services so that the settings hold and are reflected in the GUI? If not, is there any way for me to verify that the settings are correct? Step #1 - Create certificate to be used. I've configured a certificate to use with RD Web Access. The certificate is stored with in the Certificates MMC on my RD Connection Broker, and I am configuring the farm from that computer. I found by letting RD Web Access generate its own certificate that the following properties are required: Enhanced Key Usage Server Authentication Client Authentication This may not be required, but the self-signed certificate includes it. Key Usage Digital Signature Key Agreement Subject Alternative Name DNS Name=domain.com Detour about self-signed certificate generation As a quick detour, I was able to work around a problem with creating self-signed certificates using powershell. The documentation for the New-RDCertificate cmdlet gives the following example: PS C:\> $password = ConvertTo-SecureString -string "password" -asplaintext -force New-RDCertificate -Role RDWebAccess -DnsName "test-rdwa.contoso.com" -Password $password -ConnectionBroker rdcb.contoso.com -ExportPath "c:\test-rdwa.pfx" Typing this into the shell will result in an error message claiming that a function, Get-Server cannot be found. Prior to using New-RDCertificate, you must import the RemoteDesktop Module with Import-Module RemoteDesktop. Step #2 - Observe out-of-box behavior The first time you visit the Deployment Properties dialog box by navigating to Server Manager - Remote Desktop Services - Collections and selecting "Edit Deployment Properties" from the "TASKS" dropdown list in the "COLLECTIONS" grouping, you will see the following screen: This window is misleading because the level field is listed as "Not Configured". If I understand correctly all three of the role services are using a self-signed certificate. For the RD Web Access role this can be verified by visiting the website: The certificate being used also appears in the Certificates MMC: Step #3 - Assign new certificate The Deployment Properties dialog box will allow me to select my existing certificate. The certificate must be placed within the local computers Certificates MMC in the "Personal" certificate store. The private key will need to be exportable, and you will need to provide the password. I temporarily exported my certificate to a file named temp.pfx with a password, and then imported it into Remote Desktop Services from there. Once this is done the GUI will indicate that it is ready to accept the new configuration. Once I click the "Apply" button, the GUI indicates success. This can be verified by visiting the RD Web Access web site a second time. There is no certificate error. Step #4 - The GUI fails to maintain its state If the GUI is closed and reopened, all of these settings appear to be lost. Actually, the certificate I configured is still being used. I am able to continue accessing the RD Web Access site without any certificate errors. Oddly, if I use the "Create new certificate..." button to generate a self-signed certificate this window will update to an "Untrusted" level. This setting will then be maintained through the opening and closing of the Deployment Properties dialog box. Is there anything I can do to have my settings appear to stick? I feel like something is wrong when the GUI claims I haven't fully configured certificates.

  Read the article

• postfix: Temporary lookup failure for FQDN

  - by Thufir

  I'm using the FQDN of dur.bounceme.net which I want to resolve(?) to localhost. That is, I want mail to [email protected] to get delivered to user@localhost. I've tried following the Ubuntu guide on this and seem to be going in circles a bit. root@dur:~# root@dur:~# postfix stop postfix/postfix-script: stopping the Postfix mail system root@dur:~# postfix start postfix/postfix-script: starting the Postfix mail system root@dur:~# telnet dur.bounceme.net 25 Trying 127.0.1.1... telnet: Unable to connect to remote host: Connection refused root@dur:~# root@dur:~# telnet localhost 25 Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. 220 dur.bounceme.net ESMTP Postfix (Ubuntu) ehlo dur 250-dur.bounceme.net 250-PIPELINING 250-SIZE 10240000 250-VRFY 250-ETRN 250-STARTTLS 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN mail from:[email protected] 250 2.1.0 Ok rcpt to:[email protected] 451 4.3.0 <[email protected]>: Temporary lookup failure rcpt to:thufir@localhost 451 4.3.0 <thufir@localhost>: Temporary lookup failure quit 221 2.0.0 Bye Connection closed by foreign host. root@dur:~# root@dur:~# grep telnet /var/log/mail.log Aug 28 00:24:45 dur postfix/smtpd[18256]: NOQUEUE: reject: RCPT from localhost[127.0.0.1]: 451 4.3.0 <thufir@localhost>: Temporary lookup failure; from=<[email protected]> to=<thufir@localhost> proto=ESMTP helo=<dur> Aug 28 00:24:58 dur postfix/smtpd[18256]: NOQUEUE: reject: RCPT from localhost[127.0.0.1]: 451 4.3.0 <[email protected]>: Temporary lookup failure; from=<[email protected]> to=<[email protected]> proto=ESMTP helo=<dur> Aug 28 00:54:55 dur postfix/smtpd[18825]: NOQUEUE: reject: RCPT from localhost[127.0.0.1]: 451 4.3.0 <[email protected]>: Temporary lookup failure; from=<[email protected]> to=<[email protected]> proto=ESMTP helo=<dur> Aug 28 00:55:08 dur postfix/smtpd[18825]: NOQUEUE: reject: RCPT from localhost[127.0.0.1]: 451 4.3.0 <thufir@localhost>: Temporary lookup failure; from=<[email protected]> to=<thufir@localhost> proto=ESMTP helo=<dur> root@dur:~# root@dur:~# postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases, hash:/var/lib/mailman/data/aliases append_dot_mydomain = no biff = no broken_sasl_auth_clients = yes config_directory = /etc/postfix default_transport = smtp home_mailbox = Maildir/ inet_interfaces = loopback-only mailbox_command = /usr/lib/dovecot/deliver -c /etc/dovecot/conf.d/01-mail-stack-delivery.conf -m "${EXTENSION}" mailbox_size_limit = 0 mailman_destination_recipient_limit = 1 mydestination = dur, dur.bounceme.net, localhost.bounceme.net, localhost myhostname = dur.bounceme.net mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 readme_directory = no recipient_delimiter = + relay_domains = lists.dur.bounceme.net relay_transport = relay relayhost = smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_recipient_restrictions = reject_unknown_sender_domain, reject_unknown_recipient_domain, reject_unauth_pipelining, permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination smtpd_sasl_auth_enable = yes smtpd_sasl_authenticated_header = yes smtpd_sasl_local_domain = $myhostname smtpd_sasl_path = private/dovecot-auth smtpd_sasl_security_options = noanonymous smtpd_sasl_type = dovecot smtpd_tls_auth_only = yes smtpd_tls_cert_file = /etc/ssl/certs/ssl-mail.pem smtpd_tls_key_file = /etc/ssl/private/ssl-mail.key smtpd_tls_mandatory_ciphers = medium smtpd_tls_mandatory_protocols = SSLv3, TLSv1 smtpd_tls_received_header = yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes tls_random_source = dev:/dev/urandom transport_maps = hash:/etc/postfix/transport root@dur:~#

  Read the article

• SBS2003 to SBS2011 Migration - Installation Error

  - by Shawn Gradwell

  Microsoft Small Business Server 2003 to 2011 Migration. I followed the Migration Guide from Microsoft and the source server had no errors when running the various tests prior to the migration. I have completed the destination server setup using the Answer File and the server is up and running. It all looks good, I can access Exchange and AD and the only problem is the error message when you log in stating that the setup did not complete and to check the logs. Because all looks good I am continuing the migration to the destination server. I also have to state that this client does not use Sharepoint at all. Do I have to redo everything? Herewith the logs: [4992] 121016.225454.5905: Task: Starting Add User or Group access VSS registry. [4992] 121016.225454.7645: TaskManagement: In TaskScheduler.RunTasks(): The "ConfigureSharePointVSSRegistryTask" Task threw an Exception during the Run() call:System.Security.Principal.IdentityNotMappedException: Some or all identity references could not be translated. at System.Security.Principal.NTAccount.Translate(IdentityReferenceCollection sourceAccounts, Type targetType, Boolean forceSuccess) at System.Security.Principal.NTAccount.Translate(Type targetType) at System.Security.AccessControl.CommonObjectSecurity.ModifyAccess(AccessControlModification modification, AccessRule rule, Boolean& modified) at System.Security.AccessControl.CommonObjectSecurity.AddAccessRule(AccessRule rule) at Microsoft.WindowsServerSolutions.IWorker.Tasks.ConfigureSharePointVSSRegistryTask.AddUsersToAccessRegistry(List`1 names) at Microsoft.WindowsServerSolutions.IWorker.Tasks.ConfigureSharePointVSSRegistryTask.Run(ITaskDataLink dl) at Microsoft.WindowsServerSolutions.TaskManagement.Data.Task.Run(ITaskDataLink dataLink) at Microsoft.WindowsServerSolutions.TaskManagement.TaskScheduler.RunTasks(String taskListId, String stateFileName) [4992] 121016.225454.7655: Setup: An error was encountered on the TME thread: System.Security.Principal.IdentityNotMappedException: Some or all identity references could not be translated. at System.Security.Principal.NTAccount.Translate(IdentityReferenceCollection sourceAccounts, Type targetType, Boolean forceSuccess) at System.Security.Principal.NTAccount.Translate(Type targetType) at System.Security.AccessControl.CommonObjectSecurity.ModifyAccess(AccessControlModification modification, AccessRule rule, Boolean& modified) at System.Security.AccessControl.CommonObjectSecurity.AddAccessRule(AccessRule rule) at Microsoft.WindowsServerSolutions.IWorker.Tasks.ConfigureSharePointVSSRegistryTask.AddUsersToAccessRegistry(List`1 names) at Microsoft.WindowsServerSolutions.IWorker.Tasks.ConfigureSharePointVSSRegistryTask.Run(ITaskDataLink dl) at Microsoft.WindowsServerSolutions.TaskManagement.Data.Task.Run(ITaskDataLink dataLink) at Microsoft.WindowsServerSolutions.TaskManagement.TaskScheduler.RunTasks(String taskListId, String stateFileName) at Microsoft.WindowsServerSolutions.Setup.SBSSetup.ProgressPagePresenter._RunTasks(Object sender, DoWorkEventArgs e) [4956] 121016.225455.0685: Setup: _UnhandledExceptionHandler: Setup encountered an error: System.Reflection.TargetInvocationException: Exception has been thrown by the target of an invocation. ---> System.Reflection.TargetInvocationException: The TME thread failed (see the inner exception). ---> System.Security.Principal.IdentityNotMappedException: Some or all identity references could not be translated. at System.Security.Principal.NTAccount.Translate(IdentityReferenceCollection sourceAccounts, Type targetType, Boolean forceSuccess) at System.Security.Principal.NTAccount.Translate(Type targetType) at System.Security.AccessControl.CommonObjectSecurity.ModifyAccess(AccessControlModification modification, AccessRule rule, Boolean& modified) at System.Security.AccessControl.CommonObjectSecurity.AddAccessRule(AccessRule rule) at Microsoft.WindowsServerSolutions.IWorker.Tasks.ConfigureSharePointVSSRegistryTask.AddUsersToAccessRegistry(List`1 names) at Microsoft.WindowsServerSolutions.IWorker.Tasks.ConfigureSharePointVSSRegistryTask.Run(ITaskDataLink dl) at Microsoft.WindowsServerSolutions.TaskManagement.Data.Task.Run(ITaskDataLink dataLink) at Microsoft.WindowsServerSolutions.TaskManagement.TaskScheduler.RunTasks(String taskListId, String stateFileName) at Microsoft.WindowsServerSolutions.Setup.SBSSetup.ProgressPagePresenter._RunTasks(Object sender, DoWorkEventArgs e) at System.ComponentModel.BackgroundWorker.WorkerThreadStart(Object argument) --- End of inner exception stack trace --- at Microsoft.WindowsServerSolutions.Setup.SBSSetup.ProgressPagePresenter.TasksCompleted(Object sender, RunWorkerCompletedEventArgs e) --- End of inner exception stack trace --- at System.RuntimeMethodHandle._InvokeMethodFast(IRuntimeMethodInfo method, Object target, Object[] arguments, SignatureStruct& sig, MethodAttributes methodAttributes, RuntimeType typeOwner) at System.Reflection.RuntimeMethodInfo.Invoke(Object obj, BindingFlags invokeAttr, Binder binder, Object[] parameters, CultureInfo culture, Boolean skipVisibilityChecks) at System.Delegate.DynamicInvokeImpl(Object[] args) at System.Windows.Forms.Control.InvokeMarshaledCallbackDo(ThreadMethodEntry tme) at System.Windows.Forms.Control.InvokeMarshaledCallbackHelper(Object obj) at System.Threading.ExecutionContext.runTryCode(Object userData) at System.Runtime.CompilerServices.RuntimeHelpers.ExecuteCodeWithGuaranteedCleanup(TryCode code, CleanupCode backoutCode, Object userData) at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state, Boolean ignoreSyncCtx) at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state) at System.Windows.Forms.Control.InvokeMarshaledCallback(ThreadMethodEntry tme) at System.Windows.Forms.Control.InvokeMarshaledCallbacks() at System.Windows.Forms.Control.WndProc(Message& m) at System.Windows.Forms.NativeWindow.DebuggableCallback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam) at System.Windows.Forms.UnsafeNativeMethods.DispatchMessageW(MSG& msg) at System.Windows.Forms.Application.ComponentManager.System.Windows.Forms.UnsafeNativeMethods.IMsoComponentManager.FPushMessageLoop(IntPtr dwComponentID, Int32 reason, Int32 pvLoopData) at System.Windows.Forms.Application.ThreadContext.RunMessageLoopInner(Int32 reason, ApplicationContext context) at System.Windows.Forms.Application.ThreadContext.RunMessageLoop(Int32 reason, ApplicationContext context) at Microsoft.WindowsServerSolutions.Common.Wizards.Framework.WizardChainEngine.Launch() at Microsoft.WindowsServerSolutions.Setup.SBSSetup.MainClass._LaunchWizard() at Microsoft.WindowsServerSolutions.Setup.SBSSetup.MainClass.RealMain(String[] args) at Microsoft.WindowsServerSolutions.Setup.SBSSetup.MainClass.Main(String[] args) [4956] 121016.225455.0865: Setup: Removed the password. [4956] 121016.225455.0905: Setup: Deleting scheduled task at path Microsoft\Windows\Windows Small Business Server 2011 Standard with name Setup [4956] 121016.225455.8055: Setup: Removed SBSSetup from the RunOnce.

  Read the article

• nginx + php-fpm cycle redirection error on linode new vps

  - by chifliiiii

  I'm new to nginx, and I'm trying to make my first server run. I followed this guide as I'm trying to use it for a multisite wordpress site. After installing everything, I get a 500 Internal server error. If I check logs, I see this: 012/09/27 08:55:54 [error] 11565#0: *8 rewrite or internal redirection cycle while internally redirecting to "/index.html", client: xxx.xxx.xxx.xxx, server: localhost, request: "GET /favicon.ico HTTP/1.1", host: "www.mydomain.com" 2012/09/27 08:59:32 [error] 11618#0: *1 rewrite or internal redirection cycle while internally redirecting to "/index.html", client: xxx.xxx.xxx.xxx, server: localhost, request: "GET /phpmyadmin HTTP/1.1", host: "www.mydomain.com" My conf files are the following: nano /etc/nginx/sites-available/mydomain.com server { listen 80 default_server; server_name mydomain.com *.mydomain.com; root /srv/www/aciup.com/public; access_log /srv/www/mydomain.com/log/access.log; error_log /srv/www/mydomain.com/log/error.log; location / { index index.php; try_files $uri $uri/ /index.php?$args; } # Add trailing slash to */wp-admin requests. rewrite /wp-admin$ $scheme://$host$uri/ permanent; # Directives to send expires headers and turn off 404 error logging. location ~* \.(js|css|png|jpg|jpeg|gif|ico)$ { expires 24h; log_not_found off; } # this prevents hidden files (beginning with a period) from being served location ~ /\. { access_log off; log_not_found off; deny all; } # Pass uploaded files to wp-includes/ms-files.php. rewrite /files/$ /index.php last; if ($uri !~ wp-content/plugins) { rewrite /files/(.+)$ /wp-includes/ms-files.php?file=$1 last; } # Rewrite multisite '.../wp-.*' and '.../*.php'. if (!-e $request_filename) { rewrite ^/[_0-9a-zA-Z-]+(/wp-.*) $1 last; rewrite ^/[_0-9a-zA-Z-]+.*(/wp-admin/.*\.php)$ $1 last; rewrite ^/[_0-9a-zA-Z-]+(/.*\.php)$ $1 last; } location ~ \.php$ { client_max_body_size 25M; fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_index index.php; include /etc/nginx/fastcgi_params; } } nano /etc/nginx/nginx.conf user www-data; worker_processes 4; worker_cpu_affinity 0001 0010 0100 1000; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 2048; } http { include /etc/nginx/mime.types; access_log /var/log/nginx/access.log; sendfile on; tcp_nopush on; keepalive_timeout 5; tcp_nodelay on; server_tokens off; gzip on; gzip_types text/plain text/css application/x-javascript text/xml application/xml application/xml+rss text/javascript; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } Any help will be appreciated.

  Read the article

• Severe mysqldump performance degradation using Centos Linux, 8GB PAE and MySQL 5.0.77

  - by Duncan Harris

  We use MySQL 5.0.77 on CentOS 5.5 on VMWare: Linux dev.ic.soschildrensvillages.org.uk 2.6.18-194.11.4.el5PAE #1 SMP Tue Sep 21 05:48:23 EDT 2010 i686 i686 i386 GNU/Linux We have recently upgraded from 4GB RAM to 8GB. When we did this the time of our mysqldump overnight backup jumped from under 10 minutes to over 2 hours. It also caused unresponsiveness on our plone based web site due to database load. The dump is using the optimized mysqldump format and is spooled directly through a socket to another server. Any ideas on what we could do to fix gratefully appreciated. Would a MySQL upgrade help? Anything we can do to MySQL config? Anything we can do to Linux config? Or do we have to add another server or go to 64-bit? We ran a previous (non-virtual) server on 6GB PAE and didn't notice a similar issue. This was on same MySQL version, but Centos 4.4. Server config file: [mysqld] port=3307 socket=/tmp/mysql_live.sock wait_timeout=31536000 interactive_timeout=31536000 datadir=/var/mysql/live/data user=mysql max_connections = 200 max_allowed_packet = 64M table_cache = 2048 binlog_cache_size = 128K max_heap_table_size = 32M sort_buffer_size = 2M join_buffer_size = 2M lower_case_table_names = 1 innodb_data_file_path = ibdata1:10M:autoextend innodb_buffer_pool_size=1G innodb_log_file_size=300M innodb_log_buffer_size=8M innodb_flush_log_at_trx_commit=1 innodb_file_per_table [mysqldump] # Do not buffer the whole result set in memory before writing it to # file. Required for dumping very large tables quick max_allowed_packet = 64M [mysqld_safe] # Increase the amount of open files allowed per process. Warning: Make # sure you have set the global system limit high enough! The high value # is required for a large number of opened tables open-files-limit = 8192 Server variables: mysql> show variables; +---------------------------------+------------------------------------------------------------------+ | Variable_name | Value | +---------------------------------+------------------------------------------------------------------+ | auto_increment_increment | 1 | | auto_increment_offset | 1 | | automatic_sp_privileges | ON | | back_log | 50 | | basedir | /usr/local/mysql-5.0.77-linux-i686-glibc23/ | | binlog_cache_size | 131072 | | bulk_insert_buffer_size | 8388608 | | character_set_client | latin1 | | character_set_connection | latin1 | | character_set_database | latin1 | | character_set_filesystem | binary | | character_set_results | latin1 | | character_set_server | latin1 | | character_set_system | utf8 | | character_sets_dir | /usr/local/mysql-5.0.77-linux-i686-glibc23/share/mysql/charsets/ | | collation_connection | latin1_swedish_ci | | collation_database | latin1_swedish_ci | | collation_server | latin1_swedish_ci | | completion_type | 0 | | concurrent_insert | 1 | | connect_timeout | 10 | | datadir | /var/mysql/live/data/ | | date_format | %Y-%m-%d | | datetime_format | %Y-%m-%d %H:%i:%s | | default_week_format | 0 | | delay_key_write | ON | | delayed_insert_limit | 100 | | delayed_insert_timeout | 300 | | delayed_queue_size | 1000 | | div_precision_increment | 4 | | keep_files_on_create | OFF | | engine_condition_pushdown | OFF | | expire_logs_days | 0 | | flush | OFF | | flush_time | 0 | | ft_boolean_syntax | + -><()~*:""&| | | ft_max_word_len | 84 | | ft_min_word_len | 4 | | ft_query_expansion_limit | 20 | | ft_stopword_file | (built-in) | | group_concat_max_len | 1024 | | have_archive | YES | | have_bdb | NO | | have_blackhole_engine | YES | | have_compress | YES | | have_crypt | YES | | have_csv | YES | | have_dynamic_loading | YES | | have_example_engine | NO | | have_federated_engine | YES | | have_geometry | YES | | have_innodb | YES | | have_isam | NO | | have_merge_engine | YES | | have_ndbcluster | DISABLED | | have_openssl | DISABLED | | have_ssl | DISABLED | | have_query_cache | YES | | have_raid | NO | | have_rtree_keys | YES | | have_symlink | YES | | hostname | app.ic.soschildrensvillages.org.uk | | init_connect | | | init_file | | | init_slave | | | innodb_additional_mem_pool_size | 1048576 | | innodb_autoextend_increment | 8 | | innodb_buffer_pool_awe_mem_mb | 0 | | innodb_buffer_pool_size | 1073741824 | | innodb_checksums | ON | | innodb_commit_concurrency | 0 | | innodb_concurrency_tickets | 500 | | innodb_data_file_path | ibdata1:10M:autoextend | | innodb_data_home_dir | | | innodb_adaptive_hash_index | ON | | innodb_doublewrite | ON | | innodb_fast_shutdown | 1 | | innodb_file_io_threads | 4 | | innodb_file_per_table | ON | | innodb_flush_log_at_trx_commit | 1 | | innodb_flush_method | | | innodb_force_recovery | 0 | | innodb_lock_wait_timeout | 50 | | innodb_locks_unsafe_for_binlog | OFF | | innodb_log_arch_dir | | | innodb_log_archive | OFF | | innodb_log_buffer_size | 8388608 | | innodb_log_file_size | 314572800 | | innodb_log_files_in_group | 2 | | innodb_log_group_home_dir | ./ | | innodb_max_dirty_pages_pct | 90 | | innodb_max_purge_lag | 0 | | innodb_mirrored_log_groups | 1 | | innodb_open_files | 300 | | innodb_rollback_on_timeout | OFF | | innodb_support_xa | ON | | innodb_sync_spin_loops | 20 | | innodb_table_locks | ON | | innodb_thread_concurrency | 8 | | innodb_thread_sleep_delay | 10000 | | interactive_timeout | 31536000 | | join_buffer_size | 2097152 | | key_buffer_size | 8384512 | | key_cache_age_threshold | 300 | | key_cache_block_size | 1024 | | key_cache_division_limit | 100 | | language | /usr/local/mysql-5.0.77-linux-i686-glibc23/share/mysql/english/ | | large_files_support | ON | | large_page_size | 0 | | large_pages | OFF | | lc_time_names | en_US | | license | GPL | | local_infile | ON | | locked_in_memory | OFF | | log | OFF | | log_bin | OFF | | log_bin_trust_function_creators | OFF | | log_error | | | log_queries_not_using_indexes | OFF | | log_slave_updates | OFF | | log_slow_queries | OFF | | log_warnings | 1 | | long_query_time | 10 | | low_priority_updates | OFF | | lower_case_file_system | OFF | | lower_case_table_names | 1 | | max_allowed_packet | 67108864 | | max_binlog_cache_size | 4294963200 | | max_binlog_size | 1073741824 | | max_connect_errors | 10 | | max_connections | 200 | | max_delayed_threads | 20 | | max_error_count | 64 | | max_heap_table_size | 33554432 | | max_insert_delayed_threads | 20 | | max_join_size | 18446744073709551615 | | max_length_for_sort_data | 1024 | | max_prepared_stmt_count | 16382 | | max_relay_log_size | 0 | | max_seeks_for_key | 4294967295 | | max_sort_length | 1024 | | max_sp_recursion_depth | 0 | | max_tmp_tables | 32 | | max_user_connections | 0 | | max_write_lock_count | 4294967295 | | multi_range_count | 256 | | myisam_data_pointer_size | 6 | | myisam_max_sort_file_size | 2146435072 | | myisam_recover_options | OFF | | myisam_repair_threads | 1 | | myisam_sort_buffer_size | 8388608 | | myisam_stats_method | nulls_unequal | | ndb_autoincrement_prefetch_sz | 1 | | ndb_force_send | ON | | ndb_use_exact_count | ON | | ndb_use_transactions | ON | | ndb_cache_check_time | 0 | | ndb_connectstring | | | net_buffer_length | 16384 | | net_read_timeout | 30 | | net_retry_count | 10 | | net_write_timeout | 60 | | new | OFF | | old_passwords | OFF | | open_files_limit | 8192 | | optimizer_prune_level | 1 | | optimizer_search_depth | 62 | | pid_file | /var/mysql/live/mysqld.pid | | plugin_dir | | | port | 3307 | | preload_buffer_size | 32768 | | profiling | OFF | | profiling_history_size | 15 | | protocol_version | 10 | | query_alloc_block_size | 8192 | | query_cache_limit | 1048576 | | query_cache_min_res_unit | 4096 | | query_cache_size | 0 | | query_cache_type | ON | | query_cache_wlock_invalidate | OFF | | query_prealloc_size | 8192 | | range_alloc_block_size | 4096 | | read_buffer_size | 131072 | | read_only | OFF | | read_rnd_buffer_size | 262144 | | relay_log | | | relay_log_index | | | relay_log_info_file | relay-log.info | | relay_log_purge | ON | | relay_log_space_limit | 0 | | rpl_recovery_rank | 0 | | secure_auth | OFF | | secure_file_priv | | | server_id | 0 | | skip_external_locking | ON | | skip_networking | OFF | | skip_show_database | OFF | | slave_compressed_protocol | OFF | | slave_load_tmpdir | /tmp/ | | slave_net_timeout | 3600 | | slave_skip_errors | OFF | | slave_transaction_retries | 10 | | slow_launch_time | 2 | | socket | /tmp/mysql_live.sock | | sort_buffer_size | 2097152 | | sql_big_selects | ON | | sql_mode | | | sql_notes | ON | | sql_warnings | OFF | | ssl_ca | | | ssl_capath | | | ssl_cert | | | ssl_cipher | | | ssl_key | | | storage_engine | MyISAM | | sync_binlog | 0 | | sync_frm | ON | | system_time_zone | GMT | | table_cache | 2048 | | table_lock_wait_timeout | 50 | | table_type | MyISAM | | thread_cache_size | 0 | | thread_stack | 196608 | | time_format | %H:%i:%s | | time_zone | SYSTEM | | timed_mutexes | OFF | | tmp_table_size | 33554432 | | tmpdir | /tmp/ | | transaction_alloc_block_size | 8192 | | transaction_prealloc_size | 4096 | | tx_isolation | REPEATABLE-READ | | updatable_views_with_limit | YES | | version | 5.0.77 | | version_comment | MySQL Community Server (GPL) | | version_compile_machine | i686 | | version_compile_os | pc-linux-gnu | | wait_timeout | 31536000 | +---------------------------------+------------------------------------------------------------------+ 237 rows in set (0.00 sec)

  Read the article

• OpenVPN on Tomato and Vista - can't see my network

  - by Ian

  I followed the instructions here (http://todayguesswhat.blogspot.ca/2011/03/quick-simple-vpn-setup-guide-using.html) to set up a TCP connection to OpenVPN on my Tomato router. Used TCP because the place I usually surf at seems to have the other ports blocked. My Vista laptop is able to connect to the router but I don't appear to be getting an IP address. I'm able to access my router's admin page, but I can't see the network at home. When I browse to Whatsmyip I see my home IP. Here are the results of route print -4 when I'm just connect to the library and when I've fired up the VP connection as well: Library only: =========================================================================== Interface List 22 ...00 ff c4 a0 e7 5c ...... TAP-Win32 Adapter V9 15 ...00 23 4e 20 b3 64 ...... Atheros AR9281 Wireless Network Adapter 10 ...00 23 8b 39 ec 71 ...... Marvell Yukon 88E8040T PCI-E Fast Ethernet Controller 1 ........................... Software Loopback Interface 1 11 ...00 00 00 00 00 00 00 e0 isatap.{834A8A0A-5E2C-47D0-9673-7965DE8B5470} 14 ...02 00 54 55 4e 01 ...... Teredo Tunneling Pseudo-Interface 17 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3 20 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 18 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 19 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 23 ...00 00 00 00 00 00 00 e0 isatap.{C4A0E75C-765E-4F7D-A55C-77945779816A} 34 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #5 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.1.29.1 10.1.29.117 25 10.1.29.0 255.255.255.0 On-link 10.1.29.117 281 10.1.29.117 255.255.255.255 On-link 10.1.29.117 281 10.1.29.255 255.255.255.255 On-link 10.1.29.117 281 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.1.29.117 281 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.1.29.117 281 =========================================================================== Library and TCP OpenVPN: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.1.29.1 10.1.29.117 25 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.116 30 0.0.0.0 128.0.0.0 192.168.1.1 192.168.1.116 30 10.1.29.0 255.255.255.0 On-link 10.1.29.117 281 10.1.29.117 255.255.255.255 On-link 10.1.29.117 281 10.1.29.255 255.255.255.255 On-link 10.1.29.117 281 24.212.205.68 255.255.255.255 10.1.29.1 10.1.29.117 25 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.0.0.0 128.0.0.0 192.168.1.1 192.168.1.116 30 192.168.1.0 255.255.255.0 On-link 192.168.1.116 286 192.168.1.116 255.255.255.255 On-link 192.168.1.116 286 192.168.1.255 255.255.255.255 On-link 192.168.1.116 286 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.116 286 224.0.0.0 240.0.0.0 On-link 10.1.29.117 281 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.116 286 255.255.255.255 255.255.255.255 On-link 10.1.29.117 281 =========================================================================== Thanks for any advice. I looked at one of the answers but I'm not sure if it applied to me as it said that 10...* was the vpn connection, but I appear to have 10...* when I connect just to the library.

  Read the article

• Oracle Virtual Server OEL vm fails to start - kernel panic on cpu identify

  - by Towndrunk

  I am in the process of following a guide to setup various oracle vm templates, so far I have installed OVS 2. 2 and got the OVM Manager working, imported the template for OEL5U5 and created a vm from it.. the problem comes when starting that vm. The log in the OVMM console shows the following; Update VM Status - Running Configure CPU Cap Set CPU Cap: failed:<Exception: failed:<Exception: ['xm', 'sched-credit', '-d', '32_EM11g_OVM', '-c', '0'] => Error: Domain '32_EM11g_OVM' does not exist. StackTrace: File "/opt/ovs-agent-2.3/OVSXXenVMConfig.py", line 2531, in xen_set_cpu_cap run_cmd(args=['xm', File "/opt/ovs-agent-2.3/OVSCommons.py", line 92, in run_cmd raise Exception('%s => %s' % (args, err)) The xend.log shows; [2012-11-12 16:42:01 7581] DEBUG (DevController:139) Waiting for devices vtpm [2012-11-12 16:42:01 7581] INFO (XendDomain:1180) Domain 32_EM11g_OVM (3) unpaused. [2012-11-12 16:42:03 7581] WARNING (XendDomainInfo:1907) Domain has crashed: name=32_EM11g_OVM id=3. [2012-11-12 16:42:03 7581] ERROR (XendDomainInfo:2041) VM 32_EM11g_OVM restarting too fast (Elapsed time: 11.377262 seconds). Refusing to restart to avoid loops .> [2012-11-12 16:42:03 7581] DEBUG (XendDomainInfo:2757) XendDomainInfo.destroy: domid=3 [2012-11-12 16:42:12 7581] DEBUG (XendDomainInfo:2230) Destroying device model [2012-11-12 16:42:12 7581] INFO (image:553) 32_EM11g_OVM device model terminated I have set_on_crash="preserve" in the vm.cfg and have then run xm create -c to get the console screen while booting and this is the log of what happens.. Started domain 32_EM11g_OVM (id=4) Bootdata ok (command line is ro root=LABEL=/ ) Linux version 2.6.18-194.0.0.0.3.el5xen ([email protected]) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-48)) #1 SMP Mon Mar 29 18:27:00 EDT 2010 BIOS-provided physical RAM map: Xen: 0000000000000000 - 0000000180800000 (usable)> No mptable found. Built 1 zonelists. Total pages: 1574912 Kernel command line: ro root=LABEL=/ Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) Xen reported: 1600.008 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) Software IO TLB disabled Memory: 6155256k/6299648k available (2514k kernel code, 135548k reserved, 1394k data, 184k init) Calibrating delay using timer specific routine.. 4006.42 BogoMIPS (lpj=8012858) Security Framework v1.0.0 initialized SELinux: Initializing. selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 16K (64 bytes/line) CPU: L2 Cache: 2048K (64 bytes/line) general protection fault: 0000 [1] SMP last sysfs file: CPU 0 Modules linked in: Pid: 0, comm: swapper Not tainted 2.6.18-194.0.0.0.3.el5xen #1 RIP: e030:[ffffffff80271280] [ffffffff80271280] identify_cpu+0x210/0x494 RSP: e02b:ffffffff80643f70 EFLAGS: 00010212 RAX: 0040401000810008 RBX: 0000000000000000 RCX: 00000000c001001f RDX: 0000000000404010 RSI: 0000000000000001 RDI: 0000000000000005 RBP: ffffffff8063e980 R08: 0000000000000025 R09: ffff8800019d1000 R10: 0000000000000026 R11: ffff88000102c400 R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffffffff805d2000(0000) knlGS:0000000000000000 CS: e033 DS: 0000 ES: 0000 Process swapper (pid: 0, threadinfo ffffffff80642000, task ffffffff804f4b80) Stack: 0000000000000000 ffffffff802d09bb ffffffff804f4b80 0000000000000000 0000000021100800 0000000000000000 0000000000000000 ffffffff8064cb00 0000000000000000 0000000000000000 Call Trace: [ffffffff802d09bb] kmem_cache_zalloc+0x62/0x80 [ffffffff8064cb00] start_kernel+0x210/0x224 [ffffffff8064c1e5] _sinittext+0x1e5/0x1eb Code: 0f 30 b8 73 00 00 00 f0 0f ab 45 08 e9 f0 00 00 00 48 89 ef RIP [ffffffff80271280] identify_cpu+0x210/0x494 RSP ffffffff80643f70 0 Kernel panic - not syncing: Fatal exception clear as mud to me. are there any other logs that will help me? I have now deployed another vm from the same template and used the default vm settings rather than adding more memory etc - I get exactly the same error.

  Read the article

• Why my laptop sends ARP request to itself ?

  - by user58859

  I have just started to learn about protocols. While studying the packets in wireshark, I came across a ARP request sent by my machine to my own IP. Here is the details of the packet : No. Time Source Destination Protocol Info 15 1.463563 IntelCor_aa:aa:aa Broadcast ARP Who has 192.168.1.34? Tell 0.0.0.0 Frame 15: 42 bytes on wire (336 bits), 42 bytes captured (336 bits) Arrival Time: Jan 7, 2011 18:51:43.886089000 India Standard Time Epoch Time: 1294406503.886089000 seconds [Time delta from previous captured frame: 0.123389000 seconds] [Time delta from previous displayed frame: 0.123389000 seconds] [Time since reference or first frame: 1.463563000 seconds] Frame Number: 15 Frame Length: 42 bytes (336 bits) Capture Length: 42 bytes (336 bits) [Frame is marked: False] [Frame is ignored: False] [Protocols in frame: eth:arp] [Coloring Rule Name: ARP] [Coloring Rule String: arp] Ethernet II, Src: IntelCor_aa:aa:aa (aa:aa:aa:aa:aa:aa), Dst: Broadcast (ff:ff:ff:ff:ff:ff) Destination: Broadcast (ff:ff:ff:ff:ff:ff) Address: Broadcast (ff:ff:ff:ff:ff:ff) .... ...1 .... .... .... .... = IG bit: Group address (multicast/broadcast) .... ..1. .... .... .... .... = LG bit: Locally administered address (this is NOT the factory default) Source: IntelCor_aa:aa:aa (aa:aa:aa:aa:aa:aa) Address: IntelCor_aa:aa:aa (aa:aa:aa:aa:aa:aa) .... ...0 .... .... .... .... = IG bit: Individual address (unicast) .... ..0. .... .... .... .... = LG bit: Globally unique address (factory default) Type: ARP (0x0806) Address Resolution Protocol (request) Hardware type: Ethernet (0x0001) Protocol type: IP (0x0800) Hardware size: 6 Protocol size: 4 Opcode: request (0x0001) [Is gratuitous: False] Sender MAC address: IntelCor_aa:aa:aa (aa:aa:aa:aa:aa:aa) Sender IP address: 0.0.0.0 (0.0.0.0) Target MAC address: 00:00:00_00:00:00 (00:00:00:00:00:00) Target IP address: 192.168.1.34 (192.168.1.34) Here the sender's mac address is mine(Here I have hiden my mac address). target IP is mine. Why my machine is sending ARP request to itself? I found 3 packets of this type. There was no ARP reply for these packets. Can anybody explain me why it is? (My operating system is windows-7. I am directly connected to a wifi modem. I got these packets as soon as I started my connection.) I want one suggestion also. many places I read that RFC's are enough for study about protocols. I studied the RFC 826 on ARP. I personally feel that is not enough at all. Any suggestion regarding this? Is there more then 1 RFC for a protocol? I want to study about the protocols in very detail. Can anybody guide me for this? Thanks in advance.

  Read the article

• Openvpn issue with linux

  - by catsy

  So I've tried to setup openvpn, I followed some guide but it's stuck att "initialization sequence completed" with no connection and I can't find any working solution... here's the log: $Sun Sep 23 19:14:32 2012 OpenVPN 2.1.0 i486-pc-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [MH] [PF_INET6] [eurephia] built on Jul 20 2010 Enter Auth Username:pumpedup Enter Auth Password: Sun Sep 23 19:14:37 2012 WARNING: No server certificate verification method has been enabled. See http://openvpn.net/howto.html#mitm for more info. Sun Sep 23 19:14:37 2012 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Sun Sep 23 19:14:37 2012 LZO compression initialized Sun Sep 23 19:14:37 2012 Control Channel MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Sun Sep 23 19:14:38 2012 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Sun Sep 23 19:14:38 2012 Local Options hash (VER=V4): '41690919' Sun Sep 23 19:14:38 2012 Expected Remote Options hash (VER=V4): '530fdded' Sun Sep 23 19:14:38 2012 Socket Buffers: R=[163840-131072] S=[163840-131072] Sun Sep 23 19:14:38 2012 UDPv4 link local: [undef] Sun Sep 23 19:14:38 2012 UDPv4 link remote: [AF_INET]192.162.102.162:1194 Sun Sep 23 19:14:38 2012 TLS: Initial packet from [AF_INET]192.162.102.162:1194, sid=87a95723 a6d7b7f9 Sun Sep 23 19:14:38 2012 WARNING: this configuration may cache passwords in memory -- use the auth-nocache option to prevent this Sun Sep 23 19:14:38 2012 VERIFY OK: depth=1, /C=NV/ST=NV/L=nVPN/O=nVpn/CN=nVpn_CA/[email protected] Sun Sep 23 19:14:38 2012 VERIFY OK: depth=0, /C=NV/ST=NV/L=nVPN/O=nVpn/CN=server/[email protected] Sun Sep 23 19:14:39 2012 WARNING: 'link-mtu' is used inconsistently, local='link-mtu 1542', remote='link-mtu 6042' Sun Sep 23 19:14:39 2012 WARNING: 'tun-mtu' is used inconsistently, local='tun-mtu 1500', remote='tun-mtu 6000' Sun Sep 23 19:14:39 2012 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Sun Sep 23 19:14:39 2012 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Sun Sep 23 19:14:39 2012 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Sun Sep 23 19:14:39 2012 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Sun Sep 23 19:14:39 2012 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Sun Sep 23 19:14:39 2012 [server] Peer Connection Initiated with [AF_INET]192.162.102.162:1194 Sun Sep 23 19:14:41 2012 SENT CONTROL [server]: 'PUSH_REQUEST' (status=1) Sun Sep 23 19:14:41 2012 PUSH: Received control message: 'PUSH_REPLY,redirect-gateway def1,dhcp-option DNS 8.8.8.8,dhcp-option DNS 8.8.8.8,route 10.102.162.1,topology net30,ping 10,ping-restart 120,ifconfig 10.102.162.6 10.102.162.5' Sun Sep 23 19:14:41 2012 OPTIONS IMPORT: timers and/or timeouts modified Sun Sep 23 19:14:41 2012 OPTIONS IMPORT: --ifconfig/up options modified Sun Sep 23 19:14:41 2012 OPTIONS IMPORT: route options modified Sun Sep 23 19:14:41 2012 OPTIONS IMPORT: --ip-win32 and/or --dhcp-option options modified Sun Sep 23 19:14:41 2012 ROUTE default_gateway=10.0.2.2 Sun Sep 23 19:14:41 2012 TUN/TAP device tun0 opened Sun Sep 23 19:14:41 2012 TUN/TAP TX queue length set to 100 Sun Sep 23 19:14:41 2012 /sbin/ifconfig tun0 10.102.162.6 pointopoint 10.102.162.5 mtu 1500 Sun Sep 23 19:14:41 2012 /sbin/route add -net 192.162.102.162 netmask 255.255.255.255 gw 10.0.2.2 Sun Sep 23 19:14:41 2012 /sbin/route add -net 0.0.0.0 netmask 128.0.0.0 gw 10.102.162.5 Sun Sep 23 19:14:41 2012 /sbin/route add -net 128.0.0.0 netmask 128.0.0.0 gw 10.102.162.5 Sun Sep 23 19:14:41 2012 /sbin/route add -net 10.102.162.1 netmask 255.255.255.255 gw 10.102.162.5 Sun Sep 23 19:14:41 2012 Initialization Sequence Completed

  Read the article

• Symantec Protection Suite and System Recovery 2011 Desktop Edition

  - by rihatum

  I am re-posting this as my previous question was being treated as if I am "Shopping or seeking Product Recommendations" even though I was NOT - BTW they have deleted my comments too which were not offensive in nature. anyway - I have re-phrased some parts of my question and I hope SF Admins "Do Not Modify / Edit" this one - will be most grateful for that. I have a lot of respect for the People who visit this SITE and help others ! Just To clarify : Just to go by SF rules - I am not seeking someone to Design this solution, I am simply seeking real world examples, experiences, technical expert opinions / suggestions, any tips or tricks they may have or any problems they may have faced while doing something similar above with these products. I am also not asking for Capacity Planning for Storage, We have done some research and I am seeking Expert Assurance / Suggestions. We (our company) are planning to deploy Symantec Endpoint Protection and Symantec Desktop Recovery 2011 Desktop Edition to our 3000 - 4000 workstations (Windows7 32 and 64) with a few 100s with Windows XP 32/64 Bit. I have read the implementation guide for SEP and have read tech-notes for Desktop Recovery 2011. Our team have planned to deploy this as follows : 1 x dedicated SQL 2008R2 for Symantec Endpoint Protection (Instead of using the Embedded Database) 1 x Dedicated SQL 2008R2 for Symantec Desktop Recovery 2011 (Instead of using the Embedded Database) 1 x Dedicated W2K8 R2 Box for the SEPM (Symantec Endpoint Protection Manager - Mgmt. APP) 1 x Dedicated W2K8 R2 Box for the Symantec Desktop Recovery 2011 Management Application Agent Deployment : As per Symantec Documentation for both of the above, an agent can be pushed via the Mgmt. Application (provided no firewalls are blocking ports required etc. - we have Windows firewall disabled already). Server Hardware : Per SQL Server : 16GB RAM + SAS DISKS + Dual XEON, RAID-10 for the SQL DB or I can always mount a LUN from our existing Hitachi or EMC SAN. SEPM Server : 16GB RAM + SAS DISKS + DUAL XEON System Recovery MGMT SERVER : 16GB RAM + SAS DISKS + DUAL XEON Above is the initial plan we have for 3000 - 4000 client workstation (Windows) Now my Questions :-) a) If we had these users distributed amongst two sites with AD DC / GC in each site, How would I restrict SEPM and Desktop Mgmt. solution to only check for users in their respective site ? b) At present all users are under one building but we are going to move some dept. to a new location (with dedicated connectivity), How would we control which SEPM / MGMT Server is responsible for which site ? c) We have netbackup in our environment backing up other servers, I am planning to protect these 4 (2 x SQL, 1 x SEPM, 1 x System Recovery Mgmt. Server) via netbackup or I can use System recovery 2011 server edition on all 4 of these boxes as well. (License is not an issue as we have the complete symantec portfolio included in our license). d) Now - Saving Desktop backups - What strategies have you implemented ? Any best practice recommendation for a large user base ? I was thinking to either mount a LUN from our Hitachi SAN on the Symantec Recovery Server itself or backup to the users hard drive locally and then copy it over to a network location ? Suggestions welcome :-) If you have anything to add / correct - that will be really helpful before diving into the actual implementation phase. Will be most grateful with your suggestions, recommendations and corrections with above - Many Thanks !

  Read the article

• Windows 7 inbuilt and 3rd party (de)fragmentation related queries

  - by Karan

  I have a pretty good idea of how files end up getting fragmented. That said, I just copied ~3,200 files of varying sizes (from a few KB to ~20GB) from an external USB HDD to an internal, freshly formatted (under Windows 7 x64), NTFS, 2TB, 5400RPM, WD, SATA, non-system (i.e. secondary) drive, filling it up 57%. Since it should have been very much possible for each file to have been stored in one contiguous block, I expected the drive to be fragmented not more than 1-2% at most after this rather lengthy exercise (unfortunately this older machine doesn't support USB 3.0). Windows 7's inbuilt defrag utility told me after a quick analysis that the drive was fragmented only 1% or so, which dovetailed neatly with my expectations. However, just out of curiosity I downloaded and ran the latest portable x64 version of Piriform's Defraggler, and was shocked to see the drive being reported as being ~85% fragmented! The portable version of Auslogics Disk Defrag also agreed with Defraggler, and both clearly expected to grind away for ~10 hours to completely defragment the drive. 1) How in blazes could the inbuilt and 3rd party defrag utils disagree so badly? I mean, 10-20% variance is probably understandable, but 1% and 85% are miles apart! This Engineering Windows 7 blog post states: In Windows XP, any file that is split into more than one piece is considered fragmented. Not so in Windows Vista if the fragments are large enough – the defragmentation algorithm was changed (from Windows XP) to ignore pieces of a file that are larger than 64MB. As a result, defrag in XP and defrag in Vista will report different amounts of fragmentation on a volume. ... [Please read the entire post so the quote is not taken out of context.] Could it simply be that the 3rd party defrag utils ignore this post-XP change and continue to use analysis algos similar to those XP used? 2) Assuming that the 3rd party utils aren't lying about the real extent of fragmentation (which Windows is downplaying post-XP), how could the files have even got fragmented so badly given they were just copied over afresh to an empty drive? 3) If vastly differing analysis algos explain the yawning gap, which do I believe? I'm no defrag fanatic for sure, but 85% is enough to make me seriously consider spending 10 hours defragging this drive. On the other hand, 1% reported by Windows' own defragger clearly implies that there is no cause for concern and defragging would actually have negative consequences (as per the post). Is Windows' assumption valid and should I just let it be, or will there be any noticeable performance gains after running one of the 3rd party utils for 10 hours straight? 4) I see that out of the box Windows 7 defrag is scheduled to run weekly. Does anyone know whether it defrags every single time, or only if its analysis reveals a fragmentation percentage over a set threshold? If the latter, what is this threshold and can it be changed, maybe via a Registry edit? Thanks for reading through (my first query on this wonderful site!) and for any helpful replies. Also, if you're answering question #3, please keep in mind that any speed increases post defragging with 3rd party utils vis-à-vis Windows' inbuilt program should not include pre-Vista (preferably pre-Win7) examples. Further, examples of programs that made your system boot faster won't help in this case, since this is a non-system drive (although one that'll still be used daily).

  Read the article

• Using different SSDs types (not only SATA based) as system drive

  - by Hubert Kario

  Currently I have a Thinkpad X61s and want to make it both a bit faster and a bit more power efficient. For that reason I thought that adding SSD drive would make most sense. Unfortunately, because of financial reasons, buying SSD of over 200GB capacity is out of reach for me (not only it would be worth more than the rest of the laptop, but also I currently have a 500GB drive in it, so even such a drive would be kind of a downgrade for me). During preliminary testing with a cheap Transcend 4GB Class 6 (14MiB/s streaming, 9MiB/s random read) card I experienced boot times to be reduced by half so putting the OS only on it would already would be an improvement. Unfortunately, my system now is about 11GiB in size so anything less than 16GB would be constraining. In this laptop I can connect additional drives on at least 5 different ways: using SATA-ATA converter caddy in the X6 Ultrabase using internal mini PCIe slot using integrated SDHC slot using CardBus (a.k.a PCMCIA or PC Card) slot using USB Thankfully, because I use only Linux on this PC the bootability of them is irrelevant as I can put the /boot partition on internal HDD and / on any of the above mentioned Flash memories (as I already did for the SDHC test). From what I was able to research and from my own experience those options come with rather big downsides or other problems: SATA-ATA caddy It has three downsides: I have to carry the Ultrabse with me at all times (it's not really inconvenient, but those grams do add) and couldn't disconnect it when I want to disconnect the battery It makes the bay unusable for the optical drive and occasional quick access to other hard drives the only caddies I could buy have rather flaky controllers in them so putting my OS on it would hamper its stability Internal mini PCIe slot This would be an ideal solution, if only I could find real PCIe SSDs, not only devices that could talk only SATA or ATA over PCIe mechanical connection (the ones used in Dell Mini or Asus EEE). Theoretically Samsung did release such devices but I couldn't find them in retail anywhere. Integrated SDHC slot It's a nice solution with a single drawback: the fastest 16GB SDHC card on the market can only do around 35MiB/s read and 15MiB/s write while still costing like a normal 40GB SATA SSD that's 10 times faster. Not really cost-effective. CardBus (a.k.a PCMCIA or PC Card) slot Those cards are much faster than the SDHC option (there are ones that can do well over 50MiB/s read in benchmarks) and from what I could find the PCMCIA controller in my laptop does support UDMA so it should be able to deliver comparable speeds. They still cost similarly to SD cards but at least they provide streaming performance comparable to my current HDD. USB That's the worst option. Not only is it limited to 20-30MiB/s by the interface itself the drive would stick out of the laptop so it's a big no no. The question As such I think that going the "CF in a CardBus adapter" route will be the best option. My question is: did anyone try using CF cards in CardBus adapters as system drives with Linux on Thinkpad laptops? Laptops in general? What was the real-world performance? I don't have any CF cards so I can't check how well does it work with suspend/resume, or whatever it's easy to make it work in initramfs (I'm using ArchLinux and SD card was trivial — add 3 modules in single config line and rebuilding initramfs) so any tips/gotchas on this are welcome as well.

  Read the article

• Why does my computer run slowly and freeze sometimes?

  - by Brae

  EDIT I disabled sound in the BIOS, rebooted and it hung. I removed the (previously) faulty HDD, rebooted and it hung. I have managed to get my Realtek audio manager open again after its mysterious disappearance. Subsequently my microphone is now working again, to fix it I had to uninstall audio drivers, disable audio in BIOS, install audio drivers, enable audio in BIOS. Access via network (with faulty HDD in) seems to not be triggering hangs at the moment. I think with the sound problem fixed it might play a little nicer, but I think its still going to hang. If it does, then I'm fairly sure its been narrowed down to the mobo. EDIT Pretty convinced my motherboard is the culprit, because nothing else seems to have any obvious problems (bar the hard drive, which the PC still hangs without it being plugged in) So thank you all for helping, once I get more rep ill up a few of the answers. My PC is doing some weird things... Sometimes when I open up a program, lets say Adobe Photoshop, it will load everything normally, nice and quick no problems and I can use it fine. Other times its a little odd, and it loads the program as if it's only using half of the CPU. It's pretty obvious when it does it, normally the loading screen skims past, but when it does this weird load you see it slowly tick though each thing, and the program itself becomes incredibly slow. Even Google Chrome does it sometimes. Yet when I exit and reopen the program without doing anything else, it typically opens fine without lagging. I think this problem is probably a symptom of something bigger, because of other problems I'm having. Random hangs; no matter what I have open or what I'm doing. My PC will sort of freeze up for a few seconds. If music is playing it will either loop the last second or two, or it will buzz. This only lasts for a few seconds then it returns to normal without having to restart. During this time all programs lock up and freeze, and the mouse and keyboard are useless. I am also having a weird issue with my audio jacks, without touching my PC at all, sometimes I will see a popup saying that I have unplugged something or plugged something in, neither of which has actually happened. Pretty sure this is cause by the motherboard. I recently had a 'Pink Screen of Death' (yes pink) which pointed to my audio drivers. The lockups seem to happen with some consistency when someone is accessing my shared files via my home LAN. Which leads me to believe either one of my hard drives is acting up or more likely the controller. One of my drives had a bit of a crash before, I used Spinrite and managed to recover my stuff and now the drive appears to be working okay. This is possibly adding to the problems. My best guess is something has gone wrong with my motherboard, possibly a power issue or a chip has died, I really don't know. So what I would like to know is: Have I have missed some obvious diagnostic to help figure out what it is, or should I just bite the bullet and assume its my motherboard acting up and buy a new system? dxdiag[64-bit] - http://pastebin.com/G30kb2TL PSOD (minidump) - http://pastebin.com/aZsv0H56 HWiNFO64 (system info / specs) - http://pastebin.com/X6h3K8g6

  Read the article

• Issues Converting Plain Text Into Microsoft Word Bulleted Lists

  - by user787832

  I'm a programmer. I hate status reports. I found a way to live with it. While I am working in my IDE ( Visual Slickedit ) I keep a plain text file open in one of the file/buffer tabs. As I finish things I just jot down a quick note into that file. At the end of the week that becomes my weekly status report. Example entries: The Datatables.net plugin runs very slowly in IE 8 with more than 2,000 records. I changed the way I did the server side code to process the data to make less work for the plugin to get decent performance for the IE 8 users. I made a class to wrap data from the new data collection objects into the legacy data holder objects. This will let the new database code be backward compatible with the legacy code until we can replace it. I found the bug reported by Jane. The software is fine. The database we use for the test site has data that is corrupted in a way it wouldn't be for production site At the end of the month I go back to each weekly *.txt file and paste all of the entries into a MS Word file for a monthly report. I give the monthly report to a liason to the contracting company who has to compile everyone's monthly reports into a single MS Word 2007 document. His problem, soon to be my problem, comes when he highlights my paragraphs like the ones above to put bullets in front of my paragraphs. When he highlights my notes to put bullets in front of them with MS Word 2007, Word rearranges the text a bit and the new line chars/carriage returns stagger the text so the text is no longer in neat chunks. This: I found the bug reported by Jane. The software is fine. The database we use for the test site has data that is corrupted in a way it wouldn't be for production site Becomes This: I found the bug reported by Jane. The software is fine. The database we use for the test site has data that is corrupted in a way it wouldn't be for production site I tried turning word wrap on in my IDE for the text files I put my status notes in. It just puts some kind of newline character in anyway. Searching/Replacing those chars in the text files has the result of destroying the paragraphs. Once my notes are pasted into MS Word, Word automatically translates them into paragraph breaks. Searching/Replacing them there has similar results. Blank lines separating the notes disappears. One big mess. What I would like is to be able to keep adding my status notes to a text file as I am now, but do something different when I paste the notes into MS Word such that my liason can select the text, hit the bulleting command and NOT have the staggered text as shown above. Any ideas? Thanks much in advance Steve

  Read the article

• VPS 512 MB RAM with WordPressMU comes to consumes lots of memory

  - by CAPitalZ

  I have googled for days and gathered all optimization suggestions and tried. My sites are not getting any high hits. May be like 100 hits per day [all my sites combined]. Here are my specs I have 512 MB RAM VPS with burstable 1024 MB. Centos 5 32-bit & cPanel/WHM Apache 2.2 MySQL 5.0 PHP 5.3.2 Here is my Configs I have 2 WordPressMU production sites, and 1 test site my.cnf # The following options will be passed to all MySQL clients [client] #password = your_password port = 3306 socket = /var/lib/mysql/mysql.sock # Here follows entries for some specific programs # The MySQL server [mysqld] port = 3306 socket = /var/lib/mysql/mysql.sock skip-locking skip-bdb skip-innodb key_buffer = 16M max_allowed_packet = 1M table_cache = 64 sort_buffer_size = 512K net_buffer_length = 8K read_buffer_size = 256K read_rnd_buffer_size = 512K myisam_sort_buffer_size = 8M #CAPitalZ thread_cache_size=8 thread_concurrency=4 #query_cache_type=1 #query_cache_limit=1M query_cache_size=16M concurrent_insert=2 low_priority_updates=1 max_connections=50 tmp_table_size=16M max_heap_table_size=16M join_buffer_size=1M interactive_timeout=25 wait_timeout=1000 #connect_timout=10 not able to restart mysql max_connect_errors=10 # Don't listen on a TCP/IP port at all. This can be a security enhancement, # if all processes that need to connect to mysqld run on the same host. # All interaction with mysqld must be made via Unix sockets or named pipes. # Note that using this option without enabling named pipes on Windows # (via the "enable-named-pipe" option) will render mysqld useless! # skip-networking # Disable Federated by default skip-federated # Replication Master Server (default) # binary logging is required for replication log-bin=mysql-bin # required unique id between 1 and 2^32 - 1 # defaults to 1 if master-host is not set # but will not function as a master if omitted server-id = 1 [mysqld_safe] open_files_limit=8192 [mysqldump] quick max_allowed_packet = 16M [mysql] no-auto-rehash # Remove the next comment character if you are not familiar with SQL #safe-updates [isamchk] key_buffer = 20M sort_buffer_size = 20M read_buffer = 2M write_buffer = 2M [myisamchk] key_buffer = 20M sort_buffer_size = 20M read_buffer = 2M write_buffer = 2M [mysqlhotcopy] interactive-timeout httpd.conf I have unselected many modules and recompiled using EasyApache in WHM. Only have the following modules built Deflate Expires Fileprotect Imagemap MPM Prefork Version [default] EAccelerator for PHP Bcmath Calendar CurlSSL [I'm using Curl. But I don't have any https sites] Expat GD [for image cropping] Gettext Imap Mbregex [default] Mbstring [need both Mbregex and Mbstring for utf-8] Mysql of the system MySQL "Improved" extension. Sockets TTF (FreeType) [I'm using custom font] Zlib Under Global Configuration I only have FollowSymLinks enabled I Have TraceEnable, ServerSignature, FileETag OFF ServerTokens ProductOnly DirectoryIndex Priority has index.php as the first one I have removed Clamd [Clam Anti-virus] SpamAssasin is Off Under Tweak Settings Default catch-all/default address behavior for new accounts. This is set to "fail" All stats programs turned off I have eAccelerator installed and checked in phpinfo and its working [Pre VirtualHost Include under WHM] Timeout 20 KeepAlive On MaxKeepAliveRequests 200 KeepAliveTimeout 3 MinSpareServers 1 MaxSpareServers 3 StartServers 1 ServerLimit 50 MaxClients 50 MaxRequestsPerChild 4000 ExtendedStatus Off #ServerType standalone this throws error HostnameLookups Off <Directory "/"> AllowOverride None </Directory> My sites will take ages to load and WHM/CPanel will not even load. adadaa.com/ http://adadaa.net/ kadais.ca/ My average memory consumption is like 1000 MB! [yes always bursting] The process that consumes most CPU and also most memory is mysql But I also get like 15 httpd processes [when its bursting] I already got warning from cpuwatchcheck saying "While processing, the cpu has been maxed out for more than a 6 hour period. The current load/uptime line on the server at the time of this email is 07:00:37 up 11:30, 0 users, load average: 14.64, 16.79, 20.07" I don't know, I have tried switching these config values many different times, but nothing seems to work. Please show some light... Thanks

  Read the article

• What's the difference between find and findstr commands in Windows?

  - by Prashant Bhate

  In Windows, what are the differences between find and findstr commands? Both seems to search text in files: find c:\>find /? Searches for a text string in a file or files. FIND [/V] [/C] [/N] [/I] [/OFF[LINE]] "string" [[drive:][path]filename[ ...]] /V Displays all lines NOT containing the specified string. /C Displays only the count of lines containing the string. /N Displays line numbers with the displayed lines. /I Ignores the case of characters when searching for the string. /OFF[LINE] Do not skip files with offline attribute set. "string" Specifies the text string to find. [drive:][path]filename Specifies a file or files to search. If a path is not specified, FIND searches the text typed at the prompt or piped from another command. findstr c:\>findstr /? Searches for strings in files. FINDSTR [/B] [/E] [/L] [/R] [/S] [/I] [/X] [/V] [/N] [/M] [/O] [/P] [/F:file] [/C:string] [/G:file] [/D:dir list] [/A:color attributes] [/OFF[LINE]] strings [[drive:][path]filename[ ...]] /B Matches pattern if at the beginning of a line. /E Matches pattern if at the end of a line. /L Uses search strings literally. /R Uses search strings as regular expressions. /S Searches for matching files in the current directory and all subdirectories. /I Specifies that the search is not to be case-sensitive. /X Prints lines that match exactly. /V Prints only lines that do not contain a match. /N Prints the line number before each line that matches. /M Prints only the filename if a file contains a match. /O Prints character offset before each matching line. /P Skip files with non-printable characters. /OFF[LINE] Do not skip files with offline attribute set. /A:attr Specifies color attribute with two hex digits. See "color /?" /F:file Reads file list from the specified file(/ stands for console). /C:string Uses specified string as a literal search string. /G:file Gets search strings from the specified file(/ stands for console). /D:dir Search a semicolon delimited list of directories strings Text to be searched for. [drive:][path]filename Specifies a file or files to search. Use spaces to separate multiple search strings unless the argument is prefixed with /C. For example, 'FINDSTR "hello there" x.y' searches for "hello" or "there" in file x.y. 'FINDSTR /C:"hello there" x.y' searches for "hello there" in file x.y. Regular expression quick reference: . Wildcard: any character * Repeat: zero or more occurances of previous character or class ^ Line position: beginning of line $ Line position: end of line [class] Character class: any one character in set [^class] Inverse class: any one character not in set [x-y] Range: any characters within the specified range \x Escape: literal use of metacharacter x \<xyz Word position: beginning of word xyz\> Word position: end of word For full information on FINDSTR regular expressions refer to the online Command Reference.

  Read the article

< Previous Page | 368 369 370 371 372 373 374 375 376 377 378 379  | Next Page >