Search Results

Search found 19878 results on 796 pages for 'bit pirate'.

Page 374/796 | < Previous Page | 370 371 372 373 374 375 376 377 378 379 380 381  | Next Page >

• Asus z53 laptop overheating problem

  - by Tiberiu Hajas

  hi all, wondering if anyone encountered overheating of asus laptop ? especially the z53 model ? usually the right side of the laptop and vent in the upper corner is blowing hot air when under even minimal load, the CPU temperature can easily get to 65-70C and GPU is even above 80C. I'm using NHC (notebook health control) to set to a higher conservatory power consumption but that helps only a bit, anyone opened up the case ? wondering is require a dust clean ...etc ? I still have some warranty on it. thanks

  Read the article

• I cannot install anything in ubuntu that has dependency problem

  - by phpGeek

  I wanted to install teamviewer on linux 64-bit system. What I did was to download teamviewer.deb file and install it as below: sudo dpkg -i install teamviewer.deb Then I wanted to correct dependency problem so I issued the following command: sudo apt-get install libc6:i386 libgcc1:i386 libasound2:i386 libfreetype6:i386 zlib1g:i386 libsm6:i386 libxdamage1:i386 libxext6:i386 libxfixes3:i386 libxrender1:i386 libxtst6:i386 I got the following error: E: Error, pkgProblemResolver::Resolve generated breaks, this may be caused by held packages. E: Unable to correct dependencies I then tried: sudo apt-get install -f Again I got the following error: E: Error, pkgProblemResolver::Resolve generated breaks, this may be caused by held packages. E: Unable to correct dependencies Even I tried to install gdebi, but I got the above error again. I emptied archives folder: sudo apt-get clean sudo apt-get update sudo apt-get upgrade Again I have problem installing my deb package. Is there anything I could do now to solve this problem? I've read the below article as well: Install Teamviewer using a 64-bits system but I get a dependency error EDIT: I found libperl5.14:amd64 as a broken package. I used: sudo apt-get remove libperl5.14:amd64 I got the following message: E: Unable to locate package Broken

  Read the article

• change email address format with minimal disruption

  - by femi

  Hello, all the email addresses in my organization are in the format [email protected]. this was started when we were a small organization. Now we have grown and need to use something a bit more professional like [email protected] how can this change be implemented with minimal disruption? We currently only use smarteremail. Could recieving ONLY with the old and replying with the new be a solution..till we wean our recipients off the old email address? Any suggestions are welcome. How will moving to exchange help in this instance? Can it be configured to automatically send out using a different address? Thanks

  Read the article

• pdating modules on VPS [closed]

  - by tertle

  Been trying to install openVPN on a VPS but come into a few problems when trying to start the openvpn server. Service deferred error: IPTablesServiceBase: failed to run iptables-restore [status=1]: ['FATAL: Could not load /lib/modules/2.6.18-028stab070.14/modules.dep: No such file or directory', 'FATAL: Could not load /lib/modules/2.6.18-028stab070.14/modules.dep: No such file or directory', 'iptables-restore: line 46 failed']: internet/base:1175,internet/base:752,internet/process:45,internet/process:306,internet/_baseprocess:48,internet/process:775,internet/_baseprocess:60,svc/pp:116,svc/svcnotify:26,internet/defer:238,internet/defer:307,internet/defer:323,sagent/ipts:105,sagent/ipts:39,util/error:52,util/error:32 service failed to start due to unresolved dependencies: set(['user', 'iptables_openvpn']) service failed to start due to unresolved dependencies: set(['user', 'iptables_openvpn']) service failed to start due to unresolved dependencies: set(['iptables_openvpn']) Anyway so after a bit of playing around and some advice, I found that the linux kernal and modules don't match on my server. uname -r returns: 2.6.18-028stab070.14 and ls /lib/modules returns: 2.6.18-028stab070.7 The server is running OpenVZ and my container uses ubuntu 9.10. So my question is, is it possible for me to update my modules on a VPS and if so how would I do this, or is this something I'll need to try get my host to do? Thanks in advance.

  Read the article

• UML Diagrams of Multi-Threaded Applications

  - by PersonalNexus

  For single-threaded applications I like to use class diagrams to get an overview of the architecture of that application. This type of diagram, however, hasn’t been very helpful when trying to understand heavily multi-threaded/concurrent applications, for instance because different instances of a class "live" on different threads (meaning accessing an instance is save only from the one thread it lives on). Consequently, associations between classes don’t necessarily mean that I can call methods on those objects, but instead I have to make that call on the target object's thread. Most literature I have dug up on the topic such as Designing Concurrent, Distributed, and Real-Time Applications with UML by Hassan Gomaa had some nice ideas, such as drawing thread boundaries into object diagrams, but overall seemed a bit too academic and wordy to be really useful. I don’t want to use these diagrams as a high-level view of the problem domain, but rather as a detailed description of my classes/objects, their interactions and the limitations due to thread-boundaries I mentioned above. I would therefore like to know: What types of diagrams have you found to be most helpful in understanding multi-threaded applications? Are there any extensions to classic UML that take into account the peculiarities of multi-threaded applications, e.g. through annotations illustrating that some objects might live in a certain thread while others have no thread-affinity; some fields of an object may be read from any thread, but written to only from one; some methods are synchronous and return a result while others are asynchronous that get requests queued up and return results for instance via a callback on a different thread.

  Read the article

• "The user account does not have permission to run this task"

  - by Ken

  I'm trying to get a scheduled task to run on Windows Server 2008. It has been working fine for months, and then hung, so I killed it, and now I can't get it to start. (In case it's not obvious, I'm not a Windows sysadmin by any stretch of the imagination. I inherited responsibility for this system, more or less.) The error it gives is: "The user account does not have permission to run this task". The task's "author" is "A". The task's "When running the task, use the following user account:" is "B". And my user is "C". All of A, B, C are members of the Administrators group, so I'm a bit puzzled as to why it thinks I don't have permissions to run this. Ideas?

  Read the article

• SQL server peformance, virtual memory usage

  - by user45641

  Hello, I have a very large DB used mostly for analytics. The performance overall is very sluggish. I just noticed that when running the query below, the amount of virtual memory used greatly exceeds the amount of physical memory available. Currently, physical memory is 10GB (10238 MB) whereas the virtual memory returns significantly more - 8388607 MB. That seems really wrong, but I'm at a bit of a loss on how to proceed. USE [master]; GO select cpu_count , hyperthread_ratio , physical_memory_in_bytes / 1048576 as 'mem_MB' , virtual_memory_in_bytes / 1048576 as 'virtual_mem_MB' , max_workers_count , os_error_mode , os_priority_class from sys.dm_os_sys_info

  Read the article

• Duplication of code (backend and javascript - knockout)

  - by Michal B.

  We have a new developer in our team. He seems a smart guy (he just came in so I cannot really judge). He started with implementing some small enhancements in the project (MVC3 web application using javascript - jquery and knockout). Let's say we have two values: A - quite complex calculation C - constant B = A + C On the screen there is value B and user can change it (normal texbox). When B changes, A changes as well because C is constant. So there is linear dependency between A and B. Now, all the calculations are done in the backend, but we need to recalculate A as user changes B (in js, I would use knockout). I thought about storing old A and B and when B changes by 10 then we know that new A will be old A + 10. He says this is dirty, because it's duplication of code (we make use of the fact that they are dependent and according to him that should be only in one place in our app). I understand it's not ideal, but making AJAX request after every key press seems a bit too much. It's a really small thing and I would not post if we haven't had long discussion about it. How do you deal with such problems? Also I can imagine that using knockout implies lots of calculations on the client side, which very often leads to duplication of the same calculations from the backend. Does anyone have links to some articles/thoughts on this topic?

  Read the article

• Windows 7 admin denied access to taskmgr, system32 dir

  - by DotNet Zebra

  I have a Windows 7 (32-bit) box with 2 users, both admins (my wife and I are both developers). My admin account was created during Windows setup, hers was created later. Both accounts are in the same groups, yet we have VERY different permissions. In the beta and RC, both accounts worked identically (RC to RTM was a fresh install on this box, not an upgrade). I have a C:\bin folder with the sysinternals utilities and a bunch of other stuff. Running anything in there or in system32 just works on my account, on hers I get access denied errors (cannot access file or path). If I right click and try Run As Administrator, I still get the same thing!!!

  Read the article

• need to run command against multiple lines in file that start with ica-tcp

  - by Nick Parsells

  I want to run a command on each line of a file I have, however its a bit more complicated then I originally thought. The file contents look like this typically; however there are sometimes more connections: SESSIONNAME USERNAME ID STATE TYPE DEVICE services 0 Disc console 1 Conn t-rpal 48 Disc ica-tcp#0 bpofiretest 50 Active wdica rdp-tcp#2 a-nparsells 51 Active rdpwd ica-tcp 65536 Listen rdp-tcp 65537 Listen The command I want to run is reset session ica-tcp#0. I also want to run the same command on any additional connections that start with ica-tcp that the scripts finds in the file. How can I write a script like that in powershell? thanks!

  Read the article

• Working with multiple interfaces on a single mock.

  - by mehfuzh

  Today , I will cover a very simple topic, which can be useful in cases we want to mock different interfaces on our expected mock object.  Our target interface is simple and it looks like:   public interface IFoo : IDisposable {     void Do(); } Now, as we can see that our target interface has implemented IDisposable and in normal cases if we have to implement it in class where language rules require use to implement that as well[no doubt about it] and whether or not there can be more complex cases, we want to ensure that rather having an extra call(..As()) or constructs to prepare it for us, we should do it in the simplest way possible. Therefore, keeping that in mind, first we create a mock of IFoo var foo = Mock.Create<IFooDispose>(); Then, as we are interested with IDisposable, we simply do: var iDisposable = foo as IDisposable;   Finally, we proceed with our existing mock code. Considering the current context, we I will check if the dispose method has invoked our mock code successfully.   bool called = false;   Mock.Arrange(() => iDisposable.Dispose()).DoInstead(() => called = true);     iDisposable.Dispose();   Assert.True(called);   Further, we assert our expectation as follows: Mock.Assert(() => iDisposable.Dispose(), Occurs.Once());   Hopefully that will help a bit and stay tuned. Enjoy!!

  Read the article

• SSH access from outside to a pc inside network

  - by Raja

  I have a static IP and ADSL router linked to a linksys wireless router to which all my machines are connected. I would want to setup SVN on one of machines and provide SSH access which should be accessible by users outside my network. Would this be possible? Even just SVN access through web should be fine. Please let me know what all things should be done to achieve this ? I have Ubuntu VM running in a iMac Leopard machine and another 2 Win 7 32/64 bit machines. I can setup standalone Ubuntu or Win XP on another machine. Thanks, Raja.

  Read the article

• virtualbox ftp hangs on list command

  - by Tiddo

  Hi all, I have virtual box installed on a windows 7 64-bit computer, with Cent OS 5.5 as guest os. I want to be able to use ftp between those. I've installed vsftpd on the guest os, and the guest os uses a nat connection with the host os for internet. So far, I am able to connect to the guest os using ftp (in filezilla), but after the list command is executed, nothing happens, until the command is timed out. This happens in both active and passive mode. I do have set a pasv_min/max_port in the vsftpd.conf file, listing is enabled, and the ports are redirected in virtualbox. Also the ftp_data_port is set to 20. I also tried setting the pasv_address, but I had to set it to 127.0.0.1, but than filezilla gives me this: Command: PASV Response: 500 OOPS: bad family Command: PORT 127,0,0,1,139,204 Response: 500 OOPS: child died Can someone help me with this?

  Read the article

• Diablo 3 "freezes" periodically

  - by Shauna

  I'm running Diablo 3 (start edition, digital download) on the following: Ubuntu 12.04 64-bit (stock Unity, Gnome, etc; kernel version 3.2.0-29-generic) Wine version 1.5.11 (base, from Wine's PPA, game started with setarch i386 -3) Intel i7 920 CPU nVidia GTX260 with driver version 295.49 ("post-release updates" entry within the proprietary drivers tool), dual monitors 6GB RAM Every so often (and what appears to be at random), the game video will freeze up. I can still move the mouse, and it reacts to ctrl+alt+f2 to drop into text mode, but I can't get back to the desktop (which means I can check terminal to see what's going on after launching from terminal, especially since even in windowed mode, the secondary screen gets shut off by the game), and I can't continue to play the game. In order to get it running again, I have to restart lightdm, then relaunch the game (or, in a couple of rare cases, I had to restart the computer entirely, because running sudo service lightdmn [stop/start] doesn't appear to react). Turning down the video settings seems to have helped in some cases, but not all of them. Times it's frozen on me: The beginning of The Fallen Start quest part 6 - kill the Wretched Mother, right as you walk out of New Tristram and engage in the monsters on the northern path (repeatedly froze here until I adjusted the graphics down) Within the cinematic/event upon finding Deckard Cain While fighting the skeletons to protect Deckard Cain When about to enter Leoric's passage after Cain sends you back to where you found him That's as far as I've gotten through the game so far. Additionally, this doesn't happen on other games I play and seems to only occur with Diablo 3. Has anyone else run into this issue and know a possible cause or fix, or at least know where I can look (and what to look for) to figure out why this is happening?

  Read the article

• Problem with Ogre::Camera lookAt function when target is directly below.

  - by PigBen

  I am trying to make a class which controls a camera. It's pretty basic right now, it looks like this: class HoveringCameraController { public: void init(Ogre::Camera & camera, AnimatedBody & target, Ogre::Real height); void update(Ogre::Real time_delta); private: Ogre::Camera * camera_; AnimatedBody * target_; Ogre::Real height_; }; HoveringCameraController.cpp void HoveringCameraController::init(Ogre::Camera & camera, AnimatedBody & target, Ogre::Real height) { camera_ = &camera; target_ = &target; height_ = height; update(0.0); } void HoveringCameraController::update(Ogre::Real time_delta) { auto position = target_->getPosition(); position.y += height_; camera_->setPosition(position); camera_->lookAt(target_->getPosition()); } AnimatedBody is just a class that encapsulates an entity, it's animations and a scene node. The getPosition function is simply forwarded to it's scene node. What I want(for now) is for the camera to simply follow the AnimatedBody overhead at the distance given(the height parameter), and look down at it. It follows the object around, but it doesn't look straight down, it's tilted quite a bit in the positive Z direction. Does anybody have any idea why it would do that? If I change this line: position.y += height_; to this: position.x += height_; or this: position.z += height_; it does exactly what I would expect. It follows the object from the side or front, and looks directly at it.

  Read the article

• Do you have a contract between the Product Owner and the Team?

  - by Martin Hinshelwood

  Working in Scrum it is useful to define a Sprint Contract between the Product Owner (PO) and the implementation Team. Doing this helps to improve common understanding in, and sometimes to enforce, the relationship between the PO and the Team. This is simply an agreement between the PO for one Sprint and is not really a commercial contract and should be confirmed via an e-mail at the beginning of every Sprint. “The implementation team agrees to do its best to deliver an agreed on set of features (scope) to a defined quality standard by the end of the sprint. (Ideally they deliver what they promised, or even a bit more.) The Product Owner agrees not to change his instructions before the end of the Sprint.” - Agile Project management (http://agilesoftwaredevelopment.com/blog/peterstev/10-agile-contracts#Sprint) Each of the Sprints in a Scrum project can be considered a mini-project that has Time (Sprint Length), Scope (Sprint Backlog), Quality (Definition of Done) and Cost (Team Size*Sprint Length). Only the scope can vary and this is measured every sprint. Figure: Good Example, the product owner should reply to the team and commit to the contract This Rule has been added to SSW’s Rules to better Scrum with TFS   Technorati Tags: SSW,Scrum,SSW Rules

  Read the article

• Huge procedurally generated 'wilderness' worlds

  - by The Communist Duck

  I'm sure you all know of games like Dwarf Fortress - massive, procedural generated wilderness and land. Something like this, taken from this very useful article. However, I was wondering how I could apply this to a much larger scale; the scale of Minecraft comes to mind (isn't that something like 8x the size of the Earth's surface?). Pseudo-infinite, I think the best term would be. The article talks about fractal perlin noise. I am no way an expert on it, but I get the general idea (it's some kind of randomly generated noise which is semi-coherent, so not just random pixel values). I could just define regions X by X in size, add some region loading type stuff, and have one bit of noise generating a region. But this would result in just huge amounts of islands. On the other extreme, I don't think I can really generate a supermassive sheet of perlin noise. And it would just be one big island, I think. I am pretty sure Perlin noise, or some noise, would be the answer in some way. I mean, the map is really nice looking. And you could replace the ascii with tiles, and get something very nice looking. Anyone have any ideas? Thanks. :D

  Read the article

• Oracle Kicks Summer off Right with Our FY14 Global Partner Kickoff

  - by Kristin Rose

  Are you ready to see what Oracle has in store for FY14? How about hearing from top Oracle Executives like Mark Hurd and Thomas Kurian, as they explain how you can make more money with Oracle? Are you reading this blog? If you answered yes to any of the above questions and want to find out how Oracle’s strategy for the next fiscal year will affect your business, don’t miss Oracle’s FY14 Global Partner Kickoff event taking place Tuesday, June 25th at 9:00AM PT. Kick start your summer by participating in this live Oracle PartnerNetwork event! Here is how you can: 1. Send questions during the live event via Twitter using @oraclepartners and #OPN in your tweets! 2. Take part in our exciting FY14 Partner Kickoff Twitter contest and get entered to win a FREE OPN Exchange pass! Do this by tweeting @oraclepartners a creative picture of your team watching the LIVE event. The winner will be selected at the end of the show! 3. Finally, help us spread the word to the Twitter community using this tweet: “Can’t wait for #Oracle’s Global FY14 Partner Kickoff tomorrow 6/25 at 9AM PT! Join the #OPN conversation! http://bit.ly/12goIPR” You can join the live event by visiting the OPN homepage or OPN's Facebook page the day of the event. Red Stack. Red team. Engineered for Growth! The OPN Communications Team 

  Read the article

• Shibboleth + IIS and Pound Reverse Proxy

  - by boburob

  Having a bit of a problem getting Shibboleth (SSO) working with ADFS and Pound. The main problem seems to be that: The website address will be https://website.domain.com Pound will then terminate the SSL and forward the traffic to the webserver on a different port (http://server.domain.com:8888) I have set up Shibboleth to protect the address http://server.domain.com:8888, which allows me to retrieve metadata and it all seems to be working fine. However the problem seems to be that ADFS is configured to protect the https website, so when Shibboleth attempts to recieve information from ADFS I get nothing except the following error: A token request was received for a relying party identified by the key 'https://msstagrevproxy.cwpintranet.com/shibboleth', but the request could not be fulfilled because the key does not identify any known relying party trust. Key: https://msstagrevproxy.cwpintranet.com/shibboleth I am not really sure how I can work around this as to retrieve the metadata from Shibboleth I have to use the https address but this does not actually exist in Shibboleth or IIS. Has anyone had any experience with this before or using any other SSO with a reverse proxy that works?

  Read the article

• Public Facing Recursive DNS Servers - iptables rules

  - by David Schwartz

  We run public-facing recursive DNS servers on Linux machines. We've been used for DNS amplification attacks. Are there any recommended iptables rules that would help mitigate these attacks? The obvious solution is just to limit outbound DNS packets to a certain traffic level. But I was hoping to find something a little bit more clever so that an attack just blocks off traffic to the victim IP address. I've searched for advice and suggestions, but they all seem to be "don't run public-facing recursive name servers". Unfortunately, we are backed into a situation where things that are not easy to change will break if we don't do so, and this is due to decisions made more than a decade ago before these attacks were an issue.

  Read the article

• How to install rgdal on Ubuntu 12.10?

  - by radek

  I'm strugling to install rgdal library on Ubuntu 12.10. Installation from within R results in error: Error: gdal-config not found The gdal-config script distributed with GDAL could not be found. If you have not installed the GDAL libraries, you can download the source from http://www.gdal.org/ If you have installed the GDAL libraries, then make sure that gdal-config is in your path. Try typing gdal-config at a shell prompt and see if it runs. If not, use: --configure-args='--with-gdal-config=/usr/local/bin/gdal-config' with appropriate values for your installation. ERROR: configuration failed for package ‘rgdal’ * removing ‘/home/rdk/R/x86_64-pc-linux-gnu-library/2.15/rgdal’ Warning in install.packages : installation of package ‘rgdal’ had non-zero exit status R-sig-Geo, this two SE questions and other websites pointed me to the requirements of libgdal1-dev. But when I tried sudo apt-get install libgdal1-dev I end up with another error message Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: libgdal1-dev : Depends: libgdal-dev but it is not going to be installed E: Unable to correct problems, you have held broken packages. Again - when I try to install libgdal-dev another dependencies error shows up The following packages have unmet dependencies: libgdal-dev : Depends: libgeos-dev but it is not going to be installed Depends: libspatialite-dev but it is not going to be installed Again trying libgeos-dev gives message: Depends: libgeos-c1 (= 3.3.3-1.1) but 3.3.3-2~precise2 is to be installed E: Unable to correct problems, you have held broken packages. and libspatialite-dev: Depends: libspatialite3 (= 3.1.0~rc2-1ubuntu1) but 3.1.0~rc2-2~precise1 is to be installed Is there any way to tame those dependencies and have rgdal running in Ubuntu? My sessionInfo() R version 2.15.1 (2012-06-22) Platform: x86_64-pc-linux-gnu (64-bit)

  Read the article

• Suggestions for wireless adapter

  - by Michael Kniskern

  I recently purchased a desktop computer and it did not come with a wireless network card. I am currently using the Belkin Wireless G USB Adapter and it is a very sub par product. It has very slow response times and download speeds with just basic browsing and downloads podcasts through iTunes. Does anyone have a better suggestion for a wireless adapter? Should I go with another USB adapter or one that connects directly into the motherboard? I am current using Windows Vista 64 bit Home Premium.

  Read the article

• Preventing possible burnout in a junior dev, or perhaps I'm not doing enough?

  - by m.edmondson

  I'm a software developer with 5 years experience over 3 companies. Within the last year a junior (brand new to the industry) has started at my current employer. I believe he is an excellent developer, who always delivers and is skilled as solving complex problems. However I'm slightly concerned that he is possibly applying himself too much for the following reasons: He begins work approximately 2 hours before most (and is expected) In his free time he has developed an application that was clearly months worth of work that is specific to our employer I and the team are completely greatful for all he is doing, and is clearly an asset to our team. However I'm worried that this is not sustainable. I can almost see that he has the same enthusiasm that I had when I began coding for work, however over the years I've realised that extra curricular work not only doesn't progress your career, but eats into your all important free time. The question I'm asking is: Should I advise him to take things a bit more slowly? Or perhaps I need to learn from him and do more for my employer out of hours?

  Read the article

• Restful WebAPI VS Regular Controllers

  - by Rohan Büchner

  I'm doing some R&D on what seems like a very confusing topic, I've also read quite a few of the other SO questions, but I feel my question might be unique enough to warrant me asking. We've never developed an app using pure WebAPI. We're trying to write a SPA style app, where the back end is fully decoupled from the front end code Assuming our service does not know anything about who is accessing/consuming it: WebAPI seems like the logical route to serve data, as opposed to using the standard MVC controllers, and serving our data via an action result and converting it to JSON. This to me at least seems like an MC design... which seems odd, and not what MVC was meant for. (look mom... no view) What would be considered normal convention in terms of performing action(y) calls? My sense is that my understanding of WebAPI is incorrect. The way I perceive WebAPI, is that its meant to be used in a CRUD sense, but what if I want to do something like: "InitialiseMonthEndPayment".... Would I need to create a WebAPI controller, called InitialiseMonthEndPaymentController, and then perform a POST... Seems a bit weird, as opposed to a MVC controller where i can just add a new action on the MonthEnd controller called InitialisePayment. Or does this require a mindset shift in terms of design? Any further links on this topic will be really useful, as my fear is we implement something that might be weird an could turn into a coding/maintenance concern later on?

  Read the article

• How to block own rpcap traffic where tshark is running?

  - by Pankaj Goyal

  Platform :- Fedora 13 32-bit machine RemoteMachine$ ./rpcapd -n ClientMachine$ tshark -w "filename" -i "any interface name" As soon as capture starts without any capture filter, thousands of packets get captured. Rpcapd binds to 2002 port by default and while establishing the connection it sends a randomly chosen port number to the client for further communication. Both client and server machines exchange tcp packets through randomly chosen ports. So, I cannot even specify the capture filter to block this rpcap related tcp traffic. Wireshark & tshark for Windows have an option "Do not capture own Rpcap Traffic" in Remote Settings in Edit Interface Dialog box. But there is no such option in tshark for linux. It will be also better if anyone can tell me how wireshark blocks rpcap traffic....

  Read the article

< Previous Page | 370 371 372 373 374 375 376 377 378 379 380 381  | Next Page >