Search Results

Search found 10196 results on 408 pages for 'features'.

Page 374/408 | < Previous Page | 370 371 372 373 374 375 376 377 378 379 380 381  | Next Page >

• Cannot access a very specific site from my router

  - by DJDarkViper

  This is a problem for me because this site is important to me. It's MY website. And sadly my email is hosted on my site (which I cant access either) When I try to access my website when connected to my Linksys E3000 router, these days it simply just doesn't go through. When I ping it, its all Request Timed Out, and when I tracert C:\Users\Kyle>tracert blackjaguarstudios.com Tracing route to blackjaguarstudios.com [199.188.204.228] over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms CISCO26565 [192.168.1.1] 2 16 ms 15 ms 11 ms 11.4.64.1 3 11 ms 9 ms 11 ms rd1cs-ge1-2-1.ok.shawcable.net [64.59.169.2] 4 20 ms 21 ms 22 ms 66.163.76.98 5 37 ms 36 ms 35 ms rc1nr-tge0-9-2-0.wp.shawcable.net [66.163.77.54] 6 112 ms 84 ms 85 ms rc2ch-pos9-0.il.shawcable.net [66.163.76.174] 7 86 ms 89 ms 90 ms rc4as-ge12-0-0.vx.shawcable.net [66.163.64.46] 8 90 ms 84 ms 85 ms eqix.xe-3-3-0.cr2.iad1.us.nlayer.net [206.223.115.61] 9 97 ms 97 ms 99 ms xe-3-3-0.cr1.atl1.us.nlayer.net [69.22.142.105] 10 128 ms 128 ms 126 ms ae1-40g.ar1.atl1.us.nlayer.net [69.31.135.130] 11 101 ms 97 ms 96 ms as16626.xe-2-0-5-102.ar1.atl1.us.nlayer.net [69.31.135.46] 12 100 ms 97 ms 197 ms 6509-sc1.abstractdns.com [207.210.114.166] 13 * * * Request timed out. 14 * * * Request timed out. 15 * * * Request timed out. 16 * * * Request timed out. 17 * * * Request timed out. 18 * * * Request timed out. 19 * * * Request timed out. 20 * * * Request timed out. 21 * * * Request timed out. 22 * * * Request timed out. 23 * * * Request timed out. 24 * * * Request timed out. 25 * * * Request timed out. 26 * * * Request timed out. 27 * * * Request timed out. 28 * * * Request timed out. 29 * * * Request timed out. 30 * * * Request timed out. Trace complete. C:\Users\Kyle> SHAW Cable being my ISP. Figuring this was all something to do with some setting I made on the router, I reset the thing back to factory defaults. Nope. So I'm at a bit of a loss what to do here, as NO device (Computers, Laptops, Tablets, Phones, PS3/ 360, etc) can access my site or its features, so it's not just my computer either. But every other site is just fine. When I connect to my neighbors router, the site comes up just fine. And shes with SHAW as well. What should I do?!

  Read the article

• KeePass justification

  - by Jeff Walker

  I work at a place that tries to take security seriously, but sadly, they often fail. Currently, one of the major ways they fail is password management. I personally have about 20 accounts (my personal user id on lots of machines). For shared "system" accounts, there are about 45 per environment; development, test, and production. I have access to 2 of those, so my personal total is somewhere around 115 accounts. Passwords have to be at least 15 characters with some extensive but standard complexity constraints, and have to be changed every 60 days or so (system accounts every year). They also should not be the same for different accounts, but that isn't enforced. Think DoD-type standards. There is no way to remember and keep up with this. It just isn't humanly possible, as far as I'm concerned. This might be a good justification of a centralized account management system, a la LDAP or ActiveDirectory, but that is a totally different battle. Currently the solution is an Excel spreadsheet. They use Excel to put a password on it, and then most people make a copy and remove the password. This makes my stomach turn. I use KeePass for this problem and it manages all of my account very well. I like the features like auto-typing, grouping, plugins, password generation, etc. It uses AES-256 encryption via the .Net framework, and while not FIPS compliant, it has a very good reputation. The only problem is that they are also very careful about using randomly downloaded software. So we have to justify every piece of software on our workstations. I have been told that they really don't want me to use this, be cause of the "sensitive nature" of storing passwords. sigh My justification has to be "VERY VERY strong". I have been tasked with writing a justification for KeePass, but as I am lazy, I would like any input that I can get from the community. What do you recommend? Is there something out there that is better or more respected than KeePass? Is there any security experts saying interesting things on this topic? Anything will help at this point. Thanks.

  Read the article

• SQL server 2008 R2 installation error

  - by Sonia

  I have a windows 7,32 bit laptop. I am the administrator with all permissions. when I click on the SQL server 2008R2 set up file,it says : "SQL server set up has encountered the following error:Failed to retreive data for this request" click on OK. I have uninstalled all the components of SQL from control panel. I used Windows installer clean up to remove the files(which I must have not done ),but still no go. The summary.txt log says: Overall summary: Final result: Failed: see details below Exit code (Decimal): 847168662 Exit facility code: 638 Exit error code: 50326 Exit message: Failed to retrieve data for this request. Start time: 2012-05-25 14:59:15 End time: 2012-05-25 15:00:09 Requested action: RunRules Log with failure: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20120525_145905\Detail.txt Exception help link: http%3a%2f%2fgo.microsoft.com%2ffwlink%3fLinkId%3d20476%26ProdName%3dMicrosoft%2bSQL%2bServer%26EvtSrc%3dsetup.rll%26EvtID%3d50000%26ProdVer%3d10.0.5500.0%26EvtType%3d0xEF814B06%400x92D13C14 Machine Properties: Machine name: EWAN-PC Machine processor count: 4 OS version: Windows Vista OS service pack: Service Pack 1 OS region: Australia OS language: English (United States) OS architecture: x86 Process architecture: 32 Bit OS clustered: No Package properties: Description: SQL Server Database Services 2008 SQLProductFamilyCode: {628F8F38-600E-493D-9946-F4178F20A8A9} ProductName: SQL2008 Type: RTM Version: 10 SPLevel: 0 Installation location: c:\385030d65c6ff61fb9\x86\setup\ Installation edition: EXPRESS User Input Settings: ACTION: RunRules CONFIGURATIONFILE: FEATURES: HELP: False INDICATEPROGRESS: False INSTANCENAME: QUIET: False QUIETSIMPLE: False RULES: GLOBALRULES,SqlUnsupportedProductBlocker,PerfMonCounterNotCorruptedCheck,Bids2005InstalledCheck,BlockInstallSxS,AclPermissionsFacet,FacetDomainControllerCheck,SSMS_IsInternetConnected,FacetWOW64PlatformCheck,FacetPowerShellCheck X86: False Configuration file: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20120525_145905\ConfigurationFile.ini Detailed results: Rules with failures: Global rules: There are no scenario-specific rules. Rules report file: The rule result report file is not available. Exception summary: The following is an exception stack listing the exceptions in outermost to innermost order Inner exceptions are being indented Exception type: Microsoft.SqlServer.Management.Sdk.Sfc.EnumeratorException Message: Failed to retrieve data for this request. Data: HelpLink.ProdName = Microsoft SQL Server HelpLink.BaseHelpUrl = http://go.microsoft.com/fwlink HelpLink.LinkId = 20476 DisableWatson = true Stack: at Microsoft.SqlServer.Setup.Chainer.Workflow.PendingActions.InvokeActions(WorkflowObject metaDb, TextWriter loggingStream) at Microsoft.SqlServer.Setup.Chainer.Workflow.ActionEngine.RunActionQueue() at Microsoft.SqlServer.Setup.Chainer.Workflow.Workflow.RunWorkflow(HandleInternalException exceptionHandler) at Microsoft.SqlServer.Chainer.Setup.Setup.RunRequestedWorkflow() at Microsoft.SqlServer.Chainer.Setup.Setup.Run() at Microsoft.SqlServer.Chainer.Setup.Setup.Start() at Microsoft.SqlServer.Chainer.Setup.Setup.Main() Inner exception type: Microsoft.SqlServer.Configuration.Sco.ScoException Message: Attempted to perform an unauthorized operation. Data: WatsonData = HKEY_LOCAL_MACHINE@SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall\Microsoft SQL Server 10 Stack: at Microsoft.SqlServer.Configuration.Sco.InternalRegistryKey.OpenSubKey(String subkey, RegistryAccess requestedAccess) at Microsoft.SqlServer.Configuration.Sco.SqlRegistryKey.OpenSubKey(String subkey, RegistryAccess requestedAccess) at Microsoft.SqlServer.Discovery.RegistryKeyExistsPropertyValueProvider.GetPropertyValue(Object[] context) at Microsoft.SqlServer.Discovery.DiscoveryEnumObject.GetPropertyValueFromProvider(IPropertyValueProvider propertyValueProvider, String machineName, Object[] context) at Microsoft.SqlServer.Discovery.ObjectInstanceSettings.IsObjectFound(String machineName, String idFilter) at Microsoft.SqlServer.Discovery.Product.FilterObjectSet(ArrayList objects, String idFilter) at Microsoft.SqlServer.Discovery.Product.GetData(EnumResult erParent) at Microsoft.SqlServer.Management.Sdk.Sfc.Environment.GetData() at Microsoft.SqlServer.Management.Sdk.Sfc.Environment.GetData(Request req, Object ci) at Microsoft.SqlServer.Management.Sdk.Sfc.Enumerator.GetData(Object connectionInfo, Request request) at Microsoft.SqlServer.Management.Sdk.Sfc.Enumerator.Process(Object connectionInfo, Request request) Inner exception type: System.UnauthorizedAccessException Message: Attempted to perform an unauthorized operation. Stack: at Microsoft.SqlServer.Configuration.Sco.InternalRegistryKey.OpenSubKey(String subkey, RegistryAccess requestedAccess) Ineed to install SQL server 2008 R2 for one of the company softwares to work. Any immediate help will be greatly appreciated. Thanks Sonia

  Read the article

• Critique My Backup and Storage Plan

  - by MetaHyperBolic

  My current storage (RAID-1 off of a hardware RAID card) and backup (a spare drive) solutions for my home network are inadequate. I have too much data scattered on various one-off drives. It is time to evolve. Backups seem simple enough, at least: lots of big drives. However, I am bewildered by the number of choices for small home storage. The Drobo S looks appealing. So does the ReadyNAS. I am not looking for bunches of shiny features, I'm mostly interested in reliability. I am not interested in building Yet Another PC to create a file server or doing something in the cloud, or whatever. I'm stupid, so I am keeping it simple. Requirements for Main Volume: Starting working space roughly 2TB, with options for growth up to 5TB RAID or something RAID-like with at least one parity drive eSATA II for speed during backups Ability to shut down gracefully when alerted of low power by a UPS Optional but Desirable: Will take 2TB drives now with options for the larger 3TB drives coming in 2010-2011 Optional but Desirable: : RAID-6 or something similar, with two parity drives Optional but Desirable: : Hot spare Ethernet connection not required, as the volume will be shared via the same machines which runs my home print server Backups: Backup performed via ROBOCOPY in mirror mode to an external hard drive via a eSATA II connection. Start with rotating between two external 2TB hard drives, will go up to six external 2TB drives. Start with a weekly backup, move to a bi-weekly backup as more drives are added. Move to 3TB drives as the size of my main volume increases. Backup drives will be stored on an off-site location. Hard drives: I plan on buying all of the same model, but different batches from different vendors. I found a "burn-in" utility with which I can pound away on the drives for a couple of weeks before adding them to the backup pool or the main volume. I estimate that I am looking at roughly $1,500 to start, once I start throwing in two TB drives for backup and four for storage. So, are there any obvious flaws in my plan? What have I overlooked? Any suggestions for the storage device for my main volume that fits my requirements? Or do I just keep it simple, 2 drives in RAID-1, then perform due diligence with my backups, accepting that I will have to buy a whole new unit when my data grows past 2TB?

  Read the article

• MacVim, Command-T: SEGV

  - by Ramon Tayag

  Details: OSX 10.7.4 I installed the latest MacVim via Homebrew: $ command-t brew install macvim ==> Downloading https://github.com/b4winckler/macvim/tarball/snapshot-64 Already downloaded: /Library/Caches/Homebrew/macvim-7.3-64.tgz ==> ./configure --with-features=huge --with-tlib=ncurses --enable-multibyte --with-macarchs=x86_64 --enable-perlinterp --enable-pythoninterp --enable-rubyinterp --enable-t ==> make getenvy ==> make ==> Caveats MacVim.app installed to: /usr/local/Cellar/macvim/7.3-64 To link the application to a normal Mac OS X location: brew linkapps or: ln -s /usr/local/Cellar/macvim/7.3-64/MacVim.app /Applications ==> Summary /usr/local/Cellar/macvim/7.3-64: 1733 files, 27M, built in 53 seconds $ command-t brew linkapps Linking /usr/local/Cellar/macvim/7.3-64/MacVim.app Finished linking. Find the links under ~/Applications. $ command-t ruby -v ruby 1.8.7 (2011-12-28 patchlevel 357) [universal-darwin11.0] $ command-t rvm list rvm rubies ree-1.8.7-2012.02 [ i686 ] ruby-1.8.7-p358 [ i686 ] ruby-1.9.2-p290 [ x86_64 ] ruby-1.9.2-p320 [ x86_64 ] ruby-1.9.3-p194 [ x86_64 ] # Default ruby not set. Try 'rvm alias create default <ruby>'. # => - current # =* - current && default # * - default $ command-t cd ~/.vim/bundle/vim-command-t/ruby/command-t ruby extconf.rb $ command-t ruby extconf.rb checking for ruby.h... yes creating Makefile $ command-t make cc -arch i386 -arch x86_64 -pipe -bundle -undefined dynamic_lookup -o ext.bundle ext.o match.o matcher.o -L. -L/System/Library/Frameworks/Ruby.framework/Versions/1.8/usr/lib -L. -arch i386 -arch x86_64 -lruby -lpthread -ldl -lobjc ld: warning: ignoring file ext.o, file was built for unsupported file format which is not the architecture being linked (i386) ld: warning: ignoring file match.o, file was built for unsupported file format which is not the architecture being linked (i386) ld: warning: ignoring file matcher.o, file was built for unsupported file format which is not the architecture being linked (i386) $ command-t mvim MacVim then opens here. But when I open Command-T, MacVim crashes and I see this in the command line: $ command-t dyld: lazy symbol binding failed: Symbol not found: _rb_intern2 Referenced from: /Users/ramon/.vim/bundle/vim-command-t/ruby/command-t/ext.bundle Expected in: flat namespace dyld: Symbol not found: _rb_intern2 Referenced from: /Users/ramon/.vim/bundle/vim-command-t/ruby/command-t/ext.bundle Expected in: flat namespace Vim: Caught deadly signal TRAP Vim: Finished. The problem I have is very similar to this, except that I switched to the system Ruby and still got the error.

  Read the article

• Tracking down rogue disk usage

  - by Amadan

  I found several other questions regarding the theory behind my problem (e.g. this, this), but I don't know how to apply the answers to my machine. # du -hsx / 11000283 / # df -kT / Filesystem Type 1K-blocks Used Available Use% Mounted on /dev/mapper/csisv13-root ext4 516032952 361387456 128432532 74% / There is a big difference between 11G (du) and 345G (df). Where are the remaining 334G? It's not in deleted files. There was only one, it was short, and I truncated it just in case. This is what remains: # lsof -a +L1 / COMMAND PID USER FD TYPE DEVICE SIZE/OFF NLINK NODE NAME zabbix_ag 4902 zabbix 1w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4902 zabbix 2w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4906 zabbix 1w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4906 zabbix 2w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4907 zabbix 1w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4907 zabbix 2w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4908 zabbix 1w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4908 zabbix 2w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4909 zabbix 1w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4909 zabbix 2w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4910 zabbix 1w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4910 zabbix 2w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) I rebooted to see if fsck does anything. But, from /var/log/boot.log, it seems there are no issues: /dev/mapper/server-root: clean, 3936097/32768000 files, 125368568/131064832 blocks Thinking maybe someone overzealously reserved root space, I checked the master record: # tune2fs -l /dev/mapper/server-root tune2fs 1.42 (29-Nov-2011) Filesystem volume name: <none> Last mounted on: / Filesystem UUID: 86430ade-cea7-46ce-979c-41769a41ecbe Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal ext_attr resize_inode dir_index filetype needs_recovery extent flex_bg sparse_super large_file huge_file uninit_bg dir_nlink extra_isize Filesystem flags: signed_directory_hash Default mount options: user_xattr acl Filesystem state: clean Errors behavior: Continue Filesystem OS type: Linux Inode count: 32768000 Block count: 131064832 Reserved block count: 6553241 Free blocks: 5696264 Free inodes: 28831903 First block: 0 Block size: 4096 Fragment size: 4096 Reserved GDT blocks: 992 Blocks per group: 32768 Fragments per group: 32768 Inodes per group: 8192 Inode blocks per group: 512 Flex block group size: 16 Filesystem created: Fri Feb 1 13:44:04 2013 Last mount time: Tue Aug 19 16:56:13 2014 Last write time: Fri Feb 1 13:51:28 2013 Mount count: 9 Maximum mount count: -1 Last checked: Fri Feb 1 13:44:04 2013 Check interval: 0 (<none>) Lifetime writes: 1215 GB Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 256 Required extra isize: 28 Desired extra isize: 28 Journal inode: 8 First orphan inode: 28836028 Default directory hash: half_md4 Directory Hash Seed: bca55ff5-f530-48d1-8347-25c004f66d43 Journal backup: inode blocks The system is: # uname -a Linux server 3.2.0-67-generic #101-Ubuntu SMP Tue Jul 15 17:46:11 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux # cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.2 LTS" Does anyone have any tips on what exactly to do to find and hopefully reclaim the missing space?

  Read the article

• Perl missing while installing nginx on centos

  - by Ahoura Ghotbi

  I am trying to install nginx on my server, however it keeps returning "./configure: error: perl 5.6.1 or higher is required" eventhough I have perl v5.8.8!!!! I have already downloaded perl and trying to configure it using the following command : ./configure --with-http_stub_status_module --with-http_perl_module --with-http_flv_module --add-module=nginx_mod_h264_streaming here is the output : [root@fst nginx-0.8.55]# ./configure --with-http_stub_status_module --with-http_perl_module --with-http_flv_module --add-module=nginx_mod_h264_streaming checking for OS + Linux 2.6.18-308.el5 x86_64 checking for C compiler ... found + using GNU C compiler + gcc version: 4.1.2 20080704 (Red Hat 4.1.2-52) checking for gcc -pipe switch ... found checking for gcc builtin atomic operations ... found checking for C99 variadic macros ... found checking for gcc variadic macros ... found checking for unistd.h ... found checking for inttypes.h ... found checking for limits.h ... found checking for sys/filio.h ... not found checking for sys/param.h ... found checking for sys/mount.h ... found checking for sys/statvfs.h ... found checking for crypt.h ... found checking for Linux specific features checking for epoll ... found checking for sendfile() ... found checking for sendfile64() ... found checking for sys/prctl.h ... found checking for prctl(PR_SET_DUMPABLE) ... found checking for sched_setaffinity() ... found checking for crypt_r() ... found checking for sys/vfs.h ... found checking for nobody group ... found checking for poll() ... found checking for /dev/poll ... not found checking for kqueue ... not found checking for crypt() ... not found checking for crypt() in libcrypt ... found checking for F_READAHEAD ... not found checking for posix_fadvise() ... found checking for O_DIRECT ... found checking for F_NOCACHE ... not found checking for directio() ... not found checking for statfs() ... found checking for statvfs() ... found checking for dlopen() ... not found checking for dlopen() in libdl ... found checking for sched_yield() ... found checking for SO_SETFIB ... not found configuring additional modules adding module in nginx_mod_h264_streaming + ngx_http_h264_streaming_module was configured checking for PCRE library ... found checking for system md library ... not found checking for system md5 library ... not found checking for OpenSSL md5 crypto library ... found checking for zlib library ... found checking for perl + perl version: v5.8.8 built for x86_64-linux-thread-multi ./configure: error: perl 5.6.1 or higher is required

  Read the article

• Remove DRM from *.pdb e-book that I own - while maintaining footnotes, etc.?

  - by ziesemer

  Background: I've already reviewed Remove DRM from ePub Files? and How can I remove DRM from Kindle books? - the answers to which have already brought me partial process. The challenge is that I have a few purchased *.pdb e-books that I purchased in years past, e.g. 2006. In particular, they were purchased from the palm eBook Store (ebooks.palm.com - now defunct, possibly part of http://www.ereader.com / Barnes & Noble?) - originally for use on a Palm Treo that has since died. Of particular note is that I have a revision / publication of a book that is no longer published, and not available as an e-book from anywhere else that I've been able to find. (I feel fortunate to have even found the *.pdb files on backup.) I have a copy of the electronic invoice for it - which includes the details necessary for unlocking - the "Purchaser's Name" and the "Unlock Code" - which is the digits of my credit card # that I had used to purchase it. Given the above information, I was surprised to be able to open the book using the Windows eReader software and unlock it. Here I am able to view the complete contents and functionality of the book as I had done on the Palm Treo - including viewing of linked annotations / footnotes, etc. Following the full spirit of Remove DRM from ePub Files?, I want to ensure that I can access this on any device of my choosing - especially now and in the future, and as new technologies arrive and disappear. Ideally, I'm just looking to accomplish the minimum necessary to allow import into calibre. Outstanding Issue: I've found a few solutions that have given me "90%" success - all based on various versions of some Python scripts - including versions 0.21 and 0.11 of "erdr2pml.py" (based on "ereader2html"). Unfortunately, unless I'm missing something, these programs are attempting to also "convert" - instead of just "decrypting". As such, the outputs are missing embedded images and/or footnotes. I.E., there is a linked, underlined, and super-scripted "a" after some text - but the content of the footnote no longer exists. I can validate this by inspecting the generated *.pmlz file, and nowhere does it contain the original footnotes that are still visible in the original *.pdb file. I'm hoping to find a process that focuses on the decryption only, instead of attempting any type of a content conversion - or if a content conversion is required / involved, that it maintains all of the features and content of the original. (Again, I'm confident that if/once a version is obtained that calibre can import, I'll be able to fulfill the rest of my requirements.)

  Read the article

• Blank displays after inactivity, mouse cursor not showing up

  - by Mike Christiansen

  I have a Windows 7 Enterprise x86 machine that is exhibiting some strange problems. After some inactivity (it varies how long it takes), when I come back to my computer, both of my monitors are black. The monitors are on, with a black display. Moving the mouse and pressing keys on the keyboard do not work. This happens at least once a day. When I first encountered the issue, I performed a hard shutdown and restarted the computer. About 10% of the time when I did this, the resolutions on my monitors were messed up. The native resolution on the primary monitor is 1600x900, and the native on my secondary is 1440x900. None of the widescreen resolutions would be present in the display properties. I had 800x600, 1024x768, and 1280x1024. As a workaround to this issue, I've found that if I plug in my secondary monitor as the primary monitor, and leave the secondary unplugged, then Windows will start in 1024x768 on the secondary. Then, I can use Windows 7's "Detect" feature and it finds the 1440x900 resolution, and sets it. Then I have to connect the primary monitor to the secondary port and set it as the primary. Then I can switch the two cables, putting the primary into the primary, the secondary into the secondary. Then use the "Detect" feature again, and it finds the correct resolutions. Some time after performing the above, I discovered that when the screens were blanked, I could simply press "Control+Alt+Delete", type in my password, and everything comes up fine - except my mouse cursor. All applications and features work as intended, except there is no mouse cursor (the mouse actually works though...). I have the "Show location of pointer when I press CTRL key" option selected, so I can press CTRL and use my mouse as normal - but I have no actual cursor. When the computer is in this state, UAC is also not functional. Whenever a UAC prompt appears, the screens go black (the original symptoms) and I have to press Escape to exit UAC. Because of the above symptoms (the UAC black screen thing, etc) I beleive winlogon.exe may be the culprit. However, I have no idea how to fix it. I am unable to restart winlogon.exe due to the problems I am having with winlogon.exe (the UAC black screen) Looking for any ideas.... More information Windows 7 x86 Enterprise Domain environment (I have a secondary account with administrator rights) Dell Optiplex 960 Cannot perform "optional" windows updates due to an activation issue (I am testing a windows 7 image, and an activation infrastructure has not been created yet. However, this issue was happening before I was unable to perform windows update, and windows was up to date at the time Updated video card driver (as an attempt to fixing the resolution issue) Disabled all power saving options Please let me know what else you need to help me solve this issue! Thanks in advance, Mike

  Read the article

• Looking for a Software to harden Windows machines

  - by MosheH

  I'm a network administrator of a small/medium network. I'm looking for a software (Free or Not) which can harden Windows Computers (XP And Win7) for the propose of hardening standalone desktop computers (not in domain network). Note: The computers are completely isolated (standalone), so i can't use active directory group policy. moreover, there are too many restriction that i need to apply, so it is not particle to set it up manual (one by one). Basically what I’m looking for is a software that can restrict and disable access for specific user accounts on the system. For Example: User john can only open one application and nothing else -- He don’t see no icon on the desktop or start menu, except for one or two applications which i want to allow. He can't Right click on the desktop, the task-bar icons are not shown, there is no folder options, etc... User marry can open a specific application and copy data to one folder on D drive. User Dan, have access to all drives but cannot install software, and so on... So far ,I've found only the following solutions, but they all seems to miss one or more feature: Desktop restriction Software 1. Faronics WINSelect The application seems to answer most of our needs except one feature which is very important to us but seems to be missing from WINSelect, which is "restriction per profile". WINSelect only allow to set up restrictions which are applied system-wide. If I have multiple user accounts on the system and want to apply different restrictions for each user, I cant. Deskman (No Restriction per user)- Same thing, no restriction per profile. Desktop Security Rx - not relevant, No Win7 Support. The only software that I've found which is offering a restriction per profile is " 1st Security Agent ". but its GUI is very complicated and not very intuitive. It's worth to mention that I'm not looking for "Internet Kiosk software" although they share some features with the one I need. All I need is a software (like http://www.faronics.com/standard/winselect/) that is offering a way to restrict Windows user interface. So IF anybody know an Hardening software which allows to set-up user restrictions on Windows systems, It will be a big, big, big help for me! Thanks to you all

  Read the article

• How should I set up my Hyper-V server and network topology?

  - by Daniel Waechter

  This is my first time setting up either Hyper-V or Windows 2008, so please bear with me. I am setting up a pretty decent server running Windows Server 2008 R2 to be a remote (colocated) Hyper-V host. It will be hosting Linux and Windows VMs, initially for developers to use but eventually also to do some web hosting and other tasks. Currently I have two VMs, one Windows and one Ubuntu Linux, running pretty well, and I plan to clone them for future use. Right now I'm considering the best ways to configure developer and administrator access to the server once it is moved into the colocation facility, and I'm seeking advice on that. My thought is to set up a VPN for access to certain features of the VMs on the server, but I have a few different options for going about this: Connect the server to an existing hardware firewall (an old-ish Netscreen 5-GT) that can create a VPN and map external IPs to the VMs, which will have their own IPs exposed through the virtual interface. One problem with this choice is that I'm the only one trained on the Netscreen, and its interface is a bit baroque, so others may have difficulty maintaining it. Advantage is that I already know how to do it, and I know it will do what I need. Connect the server directly to the network and configure the Windows 2008 firewall to restrict access to the VMs and set up a VPN. I haven't done this before, so it will have a learning curve, but I'm willing to learn if this option is better long-term than the Netscreen. Another advantage is that I won't have to train anyone on the Netscreen interface. Still, I'm not certain if the capabilities of the Windows software firewall as far as creating VPNs, setting up rules for external access to certain ports on the IPs of Hyper-V servers, etc. Will it be sufficient for my needs and easy enough to set up / maintain? Anything else? What are the limitations of my approaches? What are the best practices / what has worked well for you? Remember that I need to set up developer access as well as consumer access to some services. Is a VPN even the right choice?

  Read the article

• How to change key mappings in Cygwin's Vim

  - by Boldewyn

  I'm using Vim under Debian, Win Vista and WinXP (the latter two with Cygwin). To handle tabs more easily, I mapped <C-Left> and <C-Right> to :tab(prev|next). This mapping works like a charm on the Debian machine. On the Windows machines, however, pressing <C-Left> deletes 5 lines, as far as I can tell, and meddles with cursor position, while <C-Right> does this, too, and additionally enters Insert mode. Question: To put it in a nutshell, how can I find out, why Vim behaves as it does? Is there a way to backtrace the active commands and keystrokes? Could there be a plugin the culprit? (I didn't install one, perhaps a default include by the Cygwin distro...) If so, how can I find it? Edit 1: OK, it seems, that I got a first trace: The terminal sends for <C-Left> '^[[1;5D', and for right '^[[1;5C' (evaluated with the <C-V><C-Left> trick). If vim interprets this literally and discards the first characters, it explains the strange behaviour. Any ideas, how I could change this key mapping? Additional Diagnosis: This behaviour occurs regardless of any existing ~/.vimrc file (is therefore not related to my above mentioned mapings) and is not inherited of some /etc/vim/vimrc, since this doesn't exist in the default Cygwin installation. :verbose map doesn't yield any new insights. Either nothing or my mentioned mappings appear, based on the existence of the .vimrc file :help <C-Left> suggests, that the default would be a simple cursor movement, which is apparently not the case. Vim's version under Cygwin: VIM - Vi IMproved 7.2 (2008 Aug 9, compiled Feb 11 2010 17:36:58) Included patches: 1-264 Compiled by http://cygwin.com/ Huge version without GUI. Features included (+) or not (-): +arabic +autocmd -balloon_eval -browse ++builtin_terms +byte_offset +cindent -clientserver -clipboard +cmdline_compl +cmdline_hist +cmdline_info +comments +cryptv +cscope +cursorshape +dialog_con +diff +digraphs -dnd -ebcdic +emacs_tags +eval +ex_extra +extra_search +farsi +file_in_path +find_in_path +float +folding -footer +fork() -gettext -hangul_input +iconv +insert_expand +jumplist +keymap +langmap +libcall +linebreak +lispindent +listcmds +localmap +menu +mksession +modify_fname +mouse -mouseshape +mouse_dec -mouse_gpm -mouse_jsbterm +mouse_netterm -mouse_sysmouse +mouse_xterm +multi_byte +multi_lang -mzscheme -netbeans_intg -osfiletype +path_extra -perl +postscript +printer +profile -python +quickfix +reltime +rightleft -ruby +scrollbind +signs +smartindent -sniff +statusline -sun_workshop +syntax +tag_binary +tag_old_static -tag_any_white -tcl +terminfo +termresponse +textobjects +title -toolbar +user_commands +vertsplit +virtualedit +visual +visualextra +viminfo +vreplace +wildignore +wildmenu +windows +writebackup -X11 -xfontset -xim -xsmp -xterm_clipboard -xterm_save system vimrc file: "$VIM/vimrc" user vimrc file: "$HOME/.vimrc" user exrc file: "$HOME/.exrc" fall-back for $VIM: "/usr/share/vim" Compilation: gcc -c -I. -Iproto -DHAVE_CONFIG_H -g -O2 -D_FORTIFY_SOURCE=1 Linking: gcc -L/usr/local/lib -o vim.exe -lm -lncurses -liconv

  Read the article

• Hyper-V causes boot loop/failure on a non-Gigabyte Win8 Pro system

  - by Nick

  Hardware: Intel i7 2600K (not overclocked, SLAT compatible, virt. features enabled in bios) Asus Maximus IV Extreme-Z (Z68) 16Gb RAM 256Gb SSD Other non-trivial working parts Adding Hyper-V is causing a boot loop resulting in an attempt at automatic repair by Windows 8 after the second or third loop: I'm trying to get the Windows Phone 8 SDK installed and I've narrowed down my troubles to the Hyper-V feature in Win8. This is required to run the WP8 emulator and there are no install options to omit this feature. My first attempt completely borked the OS as I did not have a recent restore point or system image, so I did a completely clean install and made plenty of backups/restore points. I skipped the SDK install and went straight for the windows feature add-on for Hyper-V. This confirmed that Hyper-V is the issue as the same behavior resulted. I cannot find any hint in the Event Logs. Cancelling automatic recovery causes the same behavior to repeat. I don't have any other VM products installed. My only recourse is to use a restore point, try something else, install it again, and see what happens. No luck so far. I'm on my 10th attempt here. Any help would be much appreciated. EDIT: I found a collection of tips here.. http://social.msdn.microsoft.com/Forums/en-US/wptools/thread/b06cc9f2-aa5e-4cb3-9df1-0c273e1dfd68 So i've been attempting various bios settings to resolve this issue with no luck. I've tried setting 'CPUID Limit' to disabled. This seems to work partly as Win8 boots but no USB devices work at all. I also attempted disabling the usb 3.0 controller as the msdn topic lists an issue with USB controllers on Gigabyte boards. This also doesn't work. The USB devices light up but no input is received by the OS. All of my other bios CPU settings are in line with the info in the post. I'm totally stumped. Bios screenshots: http://i.imgur.com/yKN5u.png http://i.imgur.com/Y9wI4.png http://i.imgur.com/F6EuO.png

  Read the article

• mounting ext4 fs with block size of 65536

  - by seaquest

  I am doing some benchmarking on EXT4 performance on Compact Flash media. I have created an ext4 fs with block size of 65536. however I can not mount it on ubuntu-10.10-netbook-i386. (it is already mounting ext4 fs with 4096 bytes of block sizes) According to my readings on ext4 it should allow such big block sized fs. I want to hear your comments. root@ubuntu:~# mkfs.ext4 -b 65536 /dev/sda3 Warning: blocksize 65536 not usable on most systems. mke2fs 1.41.12 (17-May-2010) mkfs.ext4: 65536-byte blocks too big for system (max 4096) Proceed anyway? (y,n) y Warning: 65536-byte blocks too big for system (max 4096), forced to continue Filesystem label= OS type: Linux Block size=65536 (log=6) Fragment size=65536 (log=6) Stride=0 blocks, Stripe width=0 blocks 19968 inodes, 19830 blocks 991 blocks (5.00%) reserved for the super user First data block=0 1 block group 65528 blocks per group, 65528 fragments per group 19968 inodes per group Writing inode tables: done Creating journal (1024 blocks): done Writing superblocks and filesystem accounting information: done This filesystem will be automatically checked every 37 mounts or 180 days, whichever comes first. Use tune2fs -c or -i to override. root@ubuntu:~# tune2fs -l /dev/sda3 tune2fs 1.41.12 (17-May-2010) Filesystem volume name: <none> Last mounted on: <not available> Filesystem UUID: 4cf3f507-e7b4-463c-be11-5b408097099b Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal ext_attr resize_inode dir_index filetype extent flex_bg sparse_super large_file huge_file uninit_bg dir_nlink extra_isize Filesystem flags: signed_directory_hash Default mount options: (none) Filesystem state: clean Errors behavior: Continue Filesystem OS type: Linux Inode count: 19968 Block count: 19830 Reserved block count: 991 Free blocks: 18720 Free inodes: 19957 First block: 0 Block size: 65536 Fragment size: 65536 Blocks per group: 65528 Fragments per group: 65528 Inodes per group: 19968 Inode blocks per group: 78 Flex block group size: 16 Filesystem created: Sat Feb 5 14:39:55 2011 Last mount time: n/a Last write time: Sat Feb 5 14:40:02 2011 Mount count: 0 Maximum mount count: 37 Last checked: Sat Feb 5 14:39:55 2011 Check interval: 15552000 (6 months) Next check after: Thu Aug 4 14:39:55 2011 Lifetime writes: 70 MB Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 256 Required extra isize: 28 Desired extra isize: 28 Journal inode: 8 Default directory hash: half_md4 Directory Hash Seed: afb5b570-9d47-4786-bad2-4aacb3b73516 Journal backup: inode blocks root@ubuntu:~# mount -t ext4 /dev/sda3 /mnt/ mount: wrong fs type, bad option, bad superblock on /dev/sda3, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so

  Read the article

• Establishing a web page bookmarking process - looking for ideas to improve

  - by Matt

  Like many others, I have a process for bookmarking web pages to read later. My requirements for web page bookmarking are: Ability to bookmark pages must be available from all (within reason) platforms - PC/browser, mobile device, etc. Bookmarks must be centrally stored (implicit from #2) so that I can read the bookmarks from anywhere/any device Full text of web pages must be stored Bonus features would be: Bookmarks and page content should be full text searchable Maintain an archive indefinitely Distinguish between what's read vs. unread Bookmarked page content is cleaned up, e.g. ads eliminated, unnecessary html removed, pages better formatted for reading My current process (which addresses most of these requirements) is as follows: I set up a Gmail account with 2 labels, "Bookmarks Unread" and "Bookmarks Read" Gmail filters set up such that depending on the form of the address (using Gmail's '+string' functionality in addresses), the incoming bookmark gets labeled appropriately On each of my browsers/devices, I have an address book entry for [email protected] and [email protected]. If I want to clean up the page content, I use the Readability bookmarklet which does a great job of giving me the essential content only Anywhere I have Firefox, I use the Send Page by Email extension which, with 2 clicks, allows me to send the cleaned-up Readability page URL and content to one of the above email addresses. Where I don't have Firefox (e.g. iPhone or other mobile device) I use the native ability to send the current link via email (most/all apps have them, including the browser, RSS readers, NYTimes, etc.). In most cases (unless it's built into the particular app), this won't include the page body. The process is almost perfect. I've got the central access and ubiquitous access of Gmail as the storage mechanism, full text searchability (due to Gmail, but of course only for the URLs I send from that Firefox extension), a cleaned up page due to Readability, ability to read offline (assuming I use an IMAP client against Gmail) and permanent archiving of content, including what's been read vs. unread. The missing pieces are: The Send Page by Email Firefox extension seems to only send X bytes of a web page. Or some portion. So it limits my full text searchability. Where I don't have Firefox, I can only send the link, so no full text search at all in those cases. Instapaper looks like it meets most of my requirements (and bonus items). The only downside to me (personal preference) is that central storage is based on Instapaper vs. something more broad like Gmail, which as a generalized service and with Google behind it pretty much means it's permanent. I'm not too hung up on this, but I would definitely prefer to keep Gmail if possible. An upside of Instapaper is that it does the page clean-up as well as stores the entire page content, unlike my Firefox extension. Thoughts on addressing the gaps and improving this process further?

  Read the article

• How to find out Vim's currently mapped commandos

  - by Boldewyn

  I'm using Vim under Debian, Win Vista and WinXP (the latter two with Cygwin). To handle tabs more easily, I mapped <C-Left> and <C-Right> to :tab(prev|next). This mapping works like a charm on the Debian machine. On the Windows machines, however, pressing <C-Left> deletes 5 lines, as far as I can tell, and meddles with cursor position, while <C-Right> does this, too, and additionally enters Insert mode. Question: To put it in a nutshell, how can I find out, why Vim behaves as it does? Is there a way to backtrace the active commands and keystrokes? Could there be a plugin the culprit? (I didn't install one, perhaps a default include by the Cygwin distro...) If so, how can I find it? Additional Diagnosis: This behaviour occurs regardless of any existing ~/.vimrc file (is therefore not related to my above mentioned mapings) and is not inherited of some /etc/vim/vimrc, since this doesn't exist in the default Cygwin installation. :verbose map doesn't yield any new insights. Either nothing or my mentioned mappings appear, based on the existence of the .vimrc file :help <C-Left> suggests, that the default would be a simple cursor movement, which is apparently not the case. Vim's version under Cygwin: VIM - Vi IMproved 7.2 (2008 Aug 9, compiled Feb 11 2010 17:36:58) Included patches: 1-264 Compiled by http://cygwin.com/ Huge version without GUI. Features included (+) or not (-): +arabic +autocmd -balloon_eval -browse ++builtin_terms +byte_offset +cindent -clientserver -clipboard +cmdline_compl +cmdline_hist +cmdline_info +comments +cryptv +cscope +cursorshape +dialog_con +diff +digraphs -dnd -ebcdic +emacs_tags +eval +ex_extra +extra_search +farsi +file_in_path +find_in_path +float +folding -footer +fork() -gettext -hangul_input +iconv +insert_expand +jumplist +keymap +langmap +libcall +linebreak +lispindent +listcmds +localmap +menu +mksession +modify_fname +mouse -mouseshape +mouse_dec -mouse_gpm -mouse_jsbterm +mouse_netterm -mouse_sysmouse +mouse_xterm +multi_byte +multi_lang -mzscheme -netbeans_intg -osfiletype +path_extra -perl +postscript +printer +profile -python +quickfix +reltime +rightleft -ruby +scrollbind +signs +smartindent -sniff +statusline -sun_workshop +syntax +tag_binary +tag_old_static -tag_any_white -tcl +terminfo +termresponse +textobjects +title -toolbar +user_commands +vertsplit +virtualedit +visual +visualextra +viminfo +vreplace +wildignore +wildmenu +windows +writebackup -X11 -xfontset -xim -xsmp -xterm_clipboard -xterm_save system vimrc file: "$VIM/vimrc" user vimrc file: "$HOME/.vimrc" user exrc file: "$HOME/.exrc" fall-back for $VIM: "/usr/share/vim" Compilation: gcc -c -I. -Iproto -DHAVE_CONFIG_H -g -O2 -D_FORTIFY_SOURCE=1 Linking: gcc -L/usr/local/lib -o vim.exe -lm -lncurses -liconv

  Read the article

• Can't get virtual desktops to show up on RDWeb for Server 2012 R2

  - by Scott Chamberlain

  I built a test lab using the Windows Server 2012 R2 Preview. The initial test lab has the following configuration (I have replaced our name with "OurCompanyName" because I would like it if Google searches for our name did not cause people to come to this site, please do the same in any responses) Physical hardware running Windows Server 2012 R2 Preview full GUI, acting as Hyper-V host (joined to the test domain as testVwHost.testVw.OurCompanyName.com) with the following VM's running on it VM running 2012 R2 Core acting as domain controller for the forest testVw.OurCompanyName.com (testDC.testVw.OurCompanyName.com) VM running 2012 R2 Core with nothing running on it joined to the test domain as testIIS.testVw.OurCompanyName.com A clean install of Windows 7, all that was done to it was all windows updates where loaded and sysprep /generalize /oobe /shutdown /mode:vm was run on it A clean install of Windows 8, all that was done to it was all windows updates where loaded and sysprep /generalize /oobe /shutdown /mode:vm was run on it I then ran "Add Roles and Features" from testVwHost and chose the "Remote Desktop Services Installation", "Standard Deployment", "Virtual machine-based desktop deployment". I choose testIIS for the roles "RD Connection Broker" and "RD Web Access" and testVwHost as "RD Virtualization Host" The Install of the roles went fine, I then went to Remote Desktop Services in server manager and wet to setup Deployment Properties. I set the certificate for all 3 roles to our certificate signed by a CA for *.OurCompanyName.com. I then created a new Virtual Desktop Collection for Windows 7 and Windows 8 and both where created without issue. On the Windows 7 pool I added RemoteApp to launch WordPad, For windows 8 I did not add any RemoteApp programs. Everything now appears to be fine from a setup perspective however if I go to https://testIIS.testVw.OurCompanyName.com/RDWeb and log in as the use Administrator (or any orher user) I don't see the virtual desktops I created nor the RemoteApp publishing of WordPad. I tried adding a licensing server, using testDC as the server but that made no difference. What step did I miss in setting this up that is causing this not to show up on RDWeb? If any additional information is needed pleas let me know. I have tried every possible thing I can think of and I am just groping around in the dark now. The virtual machines running on testVwHost The configuration screen for RD Services The Windows 7 Pool The Windows 8 Pool This is logged in as testVw\Administrator

  Read the article

• How to upgrade a 1.4.3 TortoiseSVN-created repository to 1.6.x?

  - by SiegeX

  A few years ago, TortoiseSVN 1.4.3 was deployed to our software development team and we are now looking at upgrading the client to the latest 1.6.x version. I had hoped this upgrade would be transparent with the additional features and modifications being client-side. For the most part, this was true except for a very important feature -- merging. When I try to merge a feature branch back into truck I get a show-stopping "Merge tracking not supported error." Here are some facts worth noting: When the repo was first created (before I was on board), it was created via the TortoiseSVN client itself. We do not have a 'svn server daemon' per se, rather the repository folders/database resides on a share folder that is accessible from our workstation machines via file:///. This was actually an eye opener for me, I had always thought there was some SVN server daemon we were talking to. We do not have any access to the underlying machine hosting the SVN share other than the ability to read/write to the share itself. I don't even know what OS the machine is running on. This share server was chosen because its drives are backed up nightly by our IT group. In all honesty, we really don't need the merge tracking feature although it would be nice to have. For the time being it would be sufficient to be able to use a 1.6.x TortoiseSVN client on the 1.4.3 repository and have it merge (sans tracking) without error. So now the question becomes, how does one upgrade a client-created 1.4.3 repo to a 1.6.x compatible version without access to the underlying machine the repo resides on? I was hoping the TortoiseSVN client itself had the ability to do this but that does not appear to be the case. Will I be forced to copy the entire repo over to my local drive, run some svn commands to upgrade the repo locally then copy the repo back to the share point? If so, will doing this break any compatibility with the the 1.4.3 clients in case we cant upgrade them all at the same time? Thanks for the help.

  Read the article

• How to upgrade a 1.4.3 TortoiseSVN-created repository to 1.6.x?

  - by SiegeX

  A few years ago, TortoiseSVN 1.4.3 was deployed to our software development team and we are now looking at upgrading the client to the latest 1.6.x version. I had hoped this upgrade would be transparent with the additional features and modifications being client-side. For the most part, this was true except for a very important feature -- merging. When I try to merge a feature branch back into truck I get a show-stopping "Merge tracking not supported error." Here are some facts worth noting: When the repo was first created (before I was on board), it was created via the TortoiseSVN client itself. We do not have a 'svn server daemon' per se, rather the repository folders/database resides on a share folder that is accessible from our workstation machines via file:///. This was actually an eye opener for me, I had always thought there was some SVN server daemon we were talking to. We do not have any access to the underlying machine hosting the SVN share other than the ability to read/write to the share itself. I don't even know what OS the machine is running on. This share server was chosen because its drives are backed up nightly by our IT group. In all honesty, we really don't need the merge tracking feature although it would be nice to have. For the time being it would be sufficient to be able to use a 1.6.x TortoiseSVN client on the 1.4.3 repository and have it merge (sans tracking) without error. So now the question becomes, how does one upgrade a client-created 1.4.3 repo to a 1.6.x compatible version without access to the underlying machine the repo resides on? I was hoping the TortoiseSVN client itself had the ability to do this but that does not appear to be the case. Will I be forced to copy the entire repo over to my local drive, run some svn commands to upgrade the repo locally then copy the repo back to the share point? If so, will doing this break any compatibility with the the 1.4.3 clients in case we cant upgrade them all at the same time? Thanks for the help.

  Read the article

• Using IIS7 why are my PNGs being cached by the browser, but my JS and CSS files not?

  - by Craig Shearer

  I am trying to sort out caching in IIS for my site. Basically, I want nothing cached, except for .png, .js, and .css files. At my site level, I opened the HTTP Reponse Headers and used the "Set Common Hedaers..." to set content to expire immediately. I have no Output Caching profiles set at any level in IIS. I clear my browser cache then try accessing my site. When my site requests a PNG file, I see responses like: Accept-Ranges bytes Age 0 Connection Keep-Alive Content-Type image/png Date Thu, 12 Apr 2012 21:55:15 GMT Etag "83b7322de318cd1:0" Last-Modified Thu, 12 Apr 2012 19:33:45 GMT Server Microsoft-IIS/7.5 X-Powered-By ASP.NET For JS and CSS files, I see responses like: Accept-Ranges bytes Cache-Control no-cache Connection Keep-Alive Content-Encoding gzip Content-Length 597 Content-Type text/css Date Thu, 12 Apr 2012 21:55:15 GMT Etag "06e45ede15bca1:0" Last-Modified Mon, 02 Nov 2009 17:28:44 GMT Server Microsoft-IIS/7.5 Vary Accept-Encoding X-Powered-By ASP.NET Accept-Ranges bytes Cache-Control no-cache Connection Keep-Alive Content-Encoding gzip Content-Length 42060 Content-Type application/x-javascript Date Thu, 12 Apr 2012 21:55:14 GMT Etag "2356302de318cd1:0" Last-Modified Thu, 12 Apr 2012 19:33:45 GMT Server Microsoft-IIS/7.5 Vary Accept-Encoding X-Powered-By ASP.NET So, why are my PNGs able to be cached, but JS and CSS files not? Then, I go into the Output Caching feature in IIS and set up profiles for .png, .css, and .js files. This updates the web.config file as follows: <caching> <profiles> <add extension=".png" policy="CacheUntilChange" kernelCachePolicy="DontCache" /> <add extension=".css" policy="CacheUntilChange" kernelCachePolicy="DontCache" /> <add extension=".js" policy="CacheUntilChange" kernelCachePolicy="DontCache" /> </profiles> </caching> I do a "precautionary" IISReset then try accessing my site again. For PNG files, I see the following response: Accept-Ranges bytes Age 0 Connection Keep-Alive Content-Length 3833 Content-Type image/png Date Thu, 12 Apr 2012 22:02:30 GMT Etag "0548c9e2c5dc81:0" Last-Modified Tue, 22 Jan 2008 19:26:00 GMT Server Microsoft-IIS/7.5 X-Powered-By ASP.NET For CSS and JS files, I see the following responses: Accept-Ranges bytes Cache-Control no-cache,no-cache Connection Keep-Alive Content-Encoding gzip Content-Length 2680 Content-Type application/x-javascript Date Thu, 12 Apr 2012 22:02:29 GMT Etag "0f743af9015c81:0" Last-Modified Tue, 23 Oct 2007 16:20:54 GMT Server Microsoft-IIS/7.5 Vary Accept-Encoding X-Powered-By ASP.NET Accept-Ranges bytes Cache-Control no-cache,no-cache Connection Keep-Alive Content-Encoding gzip Content-Length 3831 Content-Type text/css Date Thu, 12 Apr 2012 22:02:29 GMT Etag "c3f42d2de318cd1:0" Last-Modified Thu, 12 Apr 2012 19:33:45 GMT Server Microsoft-IIS/7.5 Vary Accept-Encoding X-Powered-By ASP.NET What am I doing wrong? Have I completely misunderstood the features of IIS, or is there a bug. Most importantly, how do I achieve what I want - that is get the browser to cache only PNG, JS and CSS files?

  Read the article

• HOW TO Convert DVD to iPad(Also converts to iPods)?

  - by goodm

  DVD to iPad Converter (Also converts to iPods) DVD to iPad Converter is the easiest-to-use and fastest DVD to iPad converter for Apple iPad movie and iPad video. It can convert almost any kind of DVD to iPad movie or iPad video format. It is also a powerful DVD to iPad converter with a conversion speed that is much faster than real-time. With this converter, you can use your iPad as a portable DVD player and enjoy your favorite DVDs on your iPad. http://www.softseeking.com/prodail.aspx?proid=83" Features of this DVD to iPad Converter Three Running Modes --In Direct Mode, you can directly click the DVD menu to select the movie you want to rip. This mode is very easy for ripping DVD movies. --In Batch Mode, you can select the DVD titles or chapters you want to rip via a checkbox list. This mode is very easy for batch ripping music DVDs, MTV DVDs and episodic DVDs. --In 1-Click Mode, you just need one click to open a DVD, after which the rest of the task will be done automatically. This is a “designed-for-dummies” mode. Input Types You can convert almost any kind of DVD format to iPad. Output Splitting You can split your output video by DVD chapters and titles. Fully supports MTV DVDs and episodic DVDs. File Size and Quality Adjustment You can customize the output file size and corresponding video quality. Flexible Output Profiles You can easily customize the various video settings such as brightness, bit rate, etc. Language Selection for Subtitles and Audio Track In Direct mode and in Batch mode, you can select the subtitle and audio track language. (In 1-Click mode, the default language is chosen automatically). Video Crop You can crop your video to 16:9, 4:3, full screen, etc. Video Resize You can resize your video. For example, you can set it to "Keep aspect ratio" or "Stretch to fit screen." Other Converts DVD to MP3 audio. Supports Dolby, DTS Surround audio track. Converts to the latest iPhone, 4th generation iPad nano, nano chromatic, 2nd generation iPad touch, and Apple TV.

  Read the article

• How do i enable innodb on ubuntu server 10.04

  - by Matt

  Here is my entire my.cnf [client] port = 3306 socket = /var/run/mysqld/mysqld.sock # Here is entries for some specific programs # The following values assume you have at least 32M ram # This was formally known as [safe_mysqld]. Both versions are currently parsed. [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] key_buffer = 224M sort_buffer_size = 4M read_buffer_size = 4M read_rnd_buffer_size = 4M myisam_sort_buffer_size = 12M query_cache_size = 44M # # * Basic Settings # # # * IMPORTANT # If you make changes to these settings and your system uses apparmor, you may # also need to also adjust /etc/apparmor.d/usr.sbin.mysqld. # user = mysql socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. bind-address = 127.0.0.1 # # * Fine Tuning # #key_buffer = 16M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 8 # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP #max_connections = 100 #table_cache = 64 #thread_concurrency = 10 # # * Query Cache Configuration # query_cache_limit = 1M #query_cache_size = 16M # # * Logging and Replication # # Both location gets rotated by the cronjob. # Be aware that this log type is a performance killer. # As of 5.1 you can enable the log at runtime! #general_log_file = /var/log/mysql/mysql.log #general_log = 1 log_error = /var/log/mysql/error.log # Here you can see queries with especially long duration #log_slow_queries = /var/log/mysql/mysql-slow.log #long_query_time = 2 #log-queries-not-using-indexes # # The following can be used as easy to replay backup logs or for replication. # note: if you are setting up a replication slave, see README.Debian about # other settings you may need to change. #server-id = 1 #log_bin = /var/log/mysql/mysql-bin.log expire_logs_days = 10 max_binlog_size = 100M #binlog_do_db = include_database_name #binlog_ignore_db = include_database_name # # * InnoDB # # InnoDB is enabled by default with a 10MB datafile in /var/lib/mysql/. # Read the manual for more InnoDB related options. There are many! # # * Security Features # # Read the manual, too, if you want chroot! # chroot = /var/lib/mysql/ # # For generating SSL certificates I recommend the OpenSSL GUI "tinyca". # # ssl-ca=/etc/mysql/cacert.pem # ssl-cert=/etc/mysql/server-cert.pem # ssl-key=/etc/mysql/server-key.pem [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] #no-auto-rehash # faster start of mysql but no tab completition [isamchk] key_buffer = 16M # # * IMPORTANT: Additional settings that can override those from this file! # The files must end with '.cnf', otherwise they'll be ignored. # !includedir /etc/mysql/conf.d/ And here is my show engines call....i have no idea what i need to do to enable innodb show engines; +------------+---------+----------------------------------------------------------------+--------------+------+------------+ | Engine | Support | Comment | Transactions | XA | Savepoints | +------------+---------+----------------------------------------------------------------+--------------+------+------------+ | MyISAM | DEFAULT | Default engine as of MySQL 3.23 with great performance | NO | NO | NO | | MRG_MYISAM | YES | Collection of identical MyISAM tables | NO | NO | NO | | BLACKHOLE | YES | /dev/null storage engine (anything you write to it disappears) | NO | NO | NO | | CSV | YES | CSV storage engine | NO | NO | NO | | MEMORY | YES | Hash based, stored in memory, useful for temporary tables | NO | NO | NO | | FEDERATED | NO | Federated MySQL storage engine | NULL | NULL | NULL | | ARCHIVE | YES | Archive storage engine | NO | NO | NO | +------------+---------+----------------------------------------------------------------+--------------+------+------------+ 7 rows in set (0.00 sec)

  Read the article

• Vim configuration slow in Terminal & iTerm2 but not in MacVim

  - by Jey Balachandran

  Ideally, I want to use Vim from Terminal or iTerm2. However, it becomes unbearably slow so I had to resort to using MacVim. There is nothing wrong with MacVim, however my workflow would be much smoother if I used only Terminal/iTerm2. When its slow Loading files, in particular Rails files takes about 1 - 1.5s. Removing rails.vim decreases this time to 0.5 - 1s. In MacVim this is instantaneous. Scrolling through the rows and columns via h, j, k, l. It progressively gets slower the longer I hold down the keys. Eventually, it starts jumping rows. I have my Key Repeat set to Fast and Delay Until Repeat set to Short. After 10 - 15 minutes of usage, using plugins such as ctrlp or Command-T gets very laggy. I'd type a letter, wait 2 - 3s, then type the next. My Setup 11" MacBook Air running Mac OS X Version 10.7.3 (1.6 Ghz Intel Core 2 Duo, 4 GB DDR3) My dotfiles. > vim --version VIM - Vi IMproved 7.3 (2010 Aug 15, compiled Nov 16 2011 16:44:23) MacOS X (unix) version Included patches: 1-333 Huge version without GUI. Features included (+) or not (-): +arabic +autocmd -balloon_eval -browse ++builtin_terms +byte_offset +cindent -clientserver +clipboard +cmdline_compl +cmdline_hist +cmdline_info +comments +conceal +cryptv -cscope +cursorbind +cursorshape +dialog_con +diff +digraphs -dnd -ebcdic +emacs_tags +eval +ex_extra +extra_search +farsi +file_in_path +find_in_path +float +folding -footer +fork() -gettext -hangul_input +iconv +insert_expand +jumplist +keymap +langmap +libcall +linebreak +lispindent +listcmds +localmap -lua +menu +mksession +modify_fname +mouse -mouseshape +mouse_dec -mouse_gpm -mouse_jsbterm +mouse_netterm -mouse_sysmouse +mouse_xterm +multi_byte +multi_lang -mzscheme +netbeans_intg +path_extra -perl +persistent_undo +postscript +printer +profile +python -python3 +quickfix +reltime +rightleft +ruby +scrollbind +signs +smartindent -sniff +startuptime +statusline -sun_workshop +syntax +tag_binary +tag_old_static -tag_any_white -tcl +terminfo +termresponse +textobjects +title -toolbar +user_commands +vertsplit +virtualedit +visual +visualextra +viminfo +vreplace +wildignore +wildmenu +windows +writebackup -X11 -xfontset -xim -xsmp -xterm_clipboard -xterm_save system vimrc file: "$VIM/vimrc" user vimrc file: "$HOME/.vimrc" user exrc file: "$HOME/.exrc" fall-back for $VIM: "/usr/local/Cellar/vim/7.3.333/share/vim" Compilation: /usr/bin/llvm-gcc -c -I. -Iproto -DHAVE_CONFIG_H -DMACOS_X_UNIX -no-cpp-precomp -O3 -march=core2 -msse4.1 -w -pipe -D_FORTIFY_SOURCE=1 Linking: /usr/bin/llvm-gcc -L. -L/usr/local/lib -o vim -lm -lncurses -liconv -framework Cocoa -framework Python -lruby I've tried running without any plugins or syntax highlighting. It opens files a lot faster but still not as fast as MacVim. But the other two problems still exist. Why is my vim configuration slow? How can I improve the speed of my vim configuration within Terminal or iTerm2?

  Read the article

• Need advice on which PCI SATA Controller Card to Purchase

  - by Matt1776

  I have a major issue with the build of a machine I am trying to get up and running. My goal is to create a file server that will service the needs of my software development, personal media storage and streaming/media server needs, as well as provide a strong platform for backing up all this data in a routine, cron-job oriented German efficiency sort of way. The issue is a simple one - all my drives are SATA drives and my motherboard controller only contains 4 ports. Solving the issue has proven to be an unmitigated nightmare. I would like advice on the purchase of the following: 4 Port internal SATA / 2 Port external eSATA PCI SATA Controller Card that has the following features and/or advantages: It must function. If I plug it in and attach drives, I expect my system to still make it to the Operating System login screen. It must function on CentOS, and I mean it must function WELL and with MINIMAL hassle. If hassle is unavoidable, there shall be CLEAR CUT and EASY TO FOLLOW instructions on how to install drivers and other supporting software. I do not need nor want fakeRAID - I will be setting up any RAID configurations from within the operating system. Now, if I am able to find such a mythical device, I would be eternally grateful to whomever would be able to point me in the right direction, a direction which I assume will be paved with yellow bricks. I am prepared to pay a considerable sum of money (as SATA controller cards go) and so paying anywhere between 60 to 120 dollars will not be an issue whatsoever. Does such a magical device exist? The following link shows an "example" of the type of thing I am looking for, however, I have no way of verifying that once I plug this baby in that my system will still continue to function once I've attached the drives, or that once I've made it to the OS, I will be able to install whatever drivers or software programs I need to make it work with relative ease. It doesn't have to be dog-shit simple, but it cannot involve kernels or brain surgery. http://www.amazon.com/gp/product/B00552PLN4/ref=pd_lpo_k2_dp_sr_1?pf_rd_p=486539851&pf_rd_s=lpo-top-stripe-1&pf_rd_t=201&pf_rd_i=B003GSGMPU&pf_rd_m=ATVPDKIKX0DER&pf_rd_r=1HJG60XTZFJ48Z173HKY So does anyone have a suggestion regarding the subject I am asking about? PCI SATA Controller Cards? It would help if you've had experience with the component before - that is after all why I am asking here - for those who have had experience that I do not have. Bear in mind that this is for a home setup and that I do not have a company credit card. I have a budget with a 'relative' upper limit of about $150.00.

  Read the article

• Media Archive System with branches?

  - by Ian McEwen

  In short, how can I get VCS features (revisioning, branching, and deduplication) for a media collection that's far too large for most/all VCS systems? Background I have a 300GB music folder; unfortunately, I only have the hard drive space for this on my desktop system. However, a good portion of my collection is FLAC; therefore, I could theoretically have a space-optimized version in which I transcode all the FLAC to mp3 or some other lossy format, and use only that version on the laptop. However, a portion of my collection isn't FLAC. And that which isn't FLAC shouldn't be transcoded to an equivalent format; it won't have any space savings, which is the point. Moreover, it shouldn't be duplicated: the mp3/ogg portions of the collection should probably be exactly the same files. Thoughts One solution is to have format-specific organization of my music folders, and use some script to transcode the FLAC directory to mp3 or such into another directory. Another is some sort of hack using entirely separate copies and symbolic links for deduplication, or something similar. But these also have a disadvantage of lacking versioning; I'd like to be able to reorganize my music collection, retag things, etc. and save history. This isn't key, but would be awfully nice. I can't see it as entirely unreasonable to set up VCS hooks or something equivalent to keep directory structure synced between two copies, update tags, and transcode FLAC automatically into the space-optimized copy. Basically, the system I really want is a version control system. Two branches: one archival/desktop branch including the FLAC, one space-optimized/laptop branch without it; most VCSes would deal well with whole chunks being the same files well by compressing in a reasonable way (i.e. don't keep two copies of the same data). I could also do a lot of what I talk about above with hooks. But I don't know of any VCS that would deal with a 300GB repository with almost 20k files. Many of them would just not even initialize the whole affair; others would just do it inexpressibly slowly or otherwise badly. checkpoint looks like it's designed for something close (it's at least for media), but wouldn't do deduplication well (and I'm not convinced I'd be able to script it to do things like automatic transcoding and directory-structure syncing). So. Is there anything out there that can do all this, or should I consider it a programming project?

  Read the article

< Previous Page | 370 371 372 373 374 375 376 377 378 379 380 381  | Next Page >