Search Results

Search found 10285 results on 412 pages for 'cpu architecture'.

Page 377/412 | < Previous Page | 373 374 375 376 377 378 379 380 381 382 383 384  | Next Page >

• GRUB 2 freezing at OS selection screen, what could be the cause?

  - by Michael Kjörling

  Mains power is somewhat unreliable where I live, so every now and then, the computer gets rebooted when the PSU can't maintain proper voltage during a brown-out or momentary black-out. It's happened a few times recently that when power is restored, the BIOS POST completes successfully, GRUB starts to load and then freezes. I've seen this at the Welcome to GRUB! message, but it seems to happen more often just past the switch to the graphical OS list. At this point, the computer will not respond to anything (arrow keys, control commands, Ctrl+Alt+Del, ...) - it simply sits there displaying this image, seemingly doing nothing more. At that point, turning the computer off using the power button and letting it sit for a while (cooling down?) has allowed it to boot successfully. Turning the computer off and immediately back on seems to give the same result (successful POST then freeze in GRUB). This behavior began recently, although does not seem to be directly correlated with my hard disk woes (although it may be relevant that GRUB resides on that physical disk, I don't know). Once the computer has booted, it runs without a hitch. I know that a "proper" solution would be to invest in a UPS, but what might be causing behavior like this? I was thinking in terms of perhaps the CPU shutting down as a thermal control measure, but if that was the cause then wouldn't I see similar freezes during use (which I do not)? What else could cause freezes apparently closely but not perfectly related to the BIOS handover from POST to OS bootloader? The BIOS settings are to reset to previous power status after a power loss. Since the PC in question is almost always turned on, this means restore to full power status. I have no expansion cards installed that make any BIOS extensions known by screen output during the boot process, at least, but I do have a few expansion cards installed. Haven't made any changes in that regard in a long time, now. I haven't touched GRUB itself for a long time, whether configuration or binaries, so I don't think that's the problem. Also, it doesn't really make sense that a bug in GRUB would manifest itself only once in a blue moon but significantly more often after a power failure.

  Read the article

• TPROXY Not working with HAProxy, Ubuntu 14.04

  - by Nyxynyx

  I'm trying to use HAProxy as a fully transparent proxy using TPROXY in Ubuntu 14.04. HAProxy will be setup on the first server with eth1 111.111.250.250 and eth0 10.111.128.134. The single balanced server has eth1 and eth0 as well. eth1 is the public facing network interface while eth0 is for the private network which both servers are in. Problem: I'm able to connect to the balanced server's port 1234 directly (via eth1) but am not able to reach the balanced server via Haproxy port 1234 (which redirects to 1234 via eth0). Am I missing out something in this configuration? On the HAProxy server The current kernel is: Linux extremehash-lb2 3.13.0-24-generic #46-Ubuntu SMP Thu Apr 10 19:11:08 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux The kernel appears to have TPROXY support: # grep TPROXY /boot/config-3.13.0-24-generic CONFIG_NETFILTER_XT_TARGET_TPROXY=m HAProxy was compiled with TPROXY support: haproxy -vv HA-Proxy version 1.5.3 2014/07/25 Copyright 2000-2014 Willy Tarreau <[email protected]> Build options : TARGET = linux26 CPU = x86_64 CC = gcc CFLAGS = -g -fno-strict-aliasing OPTIONS = USE_LINUX_TPROXY=1 USE_LIBCRYPT=1 USE_STATIC_PCRE=1 Default settings : maxconn = 2000, bufsize = 16384, maxrewrite = 8192, maxpollevents = 200 Encrypted password support via crypt(3): yes Built without zlib support (USE_ZLIB not set) Compression algorithms supported : identity Built without OpenSSL support (USE_OPENSSL not set) Built with PCRE version : 8.31 2012-07-06 PCRE library supports JIT : no (USE_PCRE_JIT not set) Built with transparent proxy support using: IP_TRANSPARENT IPV6_TRANSPARENT IP_FREEBIND Available polling systems : epoll : pref=300, test result OK poll : pref=200, test result OK select : pref=150, test result OK Total: 3 (3 usable), will use epoll. In /etc/haproxy/haproxy.cfg, I've configured a port to have the following options: listen test1235 :1234 mode tcp option tcplog balance leastconn source 0.0.0.0 usesrc clientip server balanced1 10.111.163.76:1234 check inter 5s rise 2 fall 4 weight 4 On the balanced server In /etc/networking/interfaces I've set the gateway for eth0 to be the HAProxy box 10.111.128.134 and restarted networking. auto eth0 eth1 iface eth0 inet static address 111.111.250.250 netmask 255.255.224.0 gateway 111.131.224.1 dns-nameservers 8.8.4.4 8.8.8.8 209.244.0.3 iface eth1 inet static address 10.111.163.76 netmask 255.255.0.0 gateway 10.111.128.134 ip route gives: default via 111.111.224.1 dev eth0 10.111.0.0/16 dev eth1 proto kernel scope link src 10.111.163.76 111.111.224.0/19 dev eth0 proto kernel scope link src 111.111.250.250

  Read the article

• ffmpeg hangs when creating a video

  - by FearUs

  I am trying to insert an audio channel with a video: first of all I extract the audio from the original video for processing: ffmpeg -i lotr.mp4 lotr.wav I then extract all frames for later processing too: ffmpeg -i lotr.mp4 -f image2 %d.jpg When done processing audio and video streams, I try to create the video ffmpeg -f image2 -r 15 -i %d.jpg new.mp4 then merge with the audio: ffmpeg -i new.mp4 -i lotr.wav -map 0:0 -map 1:0 new_w_audio.mp4 Result: CPU activity = 100%, the process hangs and never returns. PS: I even tried it without modifying the images or the audio (so just trying to unpack then repack the video) but still the same output FFmpeg version SVN-r26400, Copyright (c) 2000-2011 the FFmpeg developers built on Jan 18 2011 04:07:05 with gcc 4.4.2 configuration: --enable-gpl --enable-version3 --enable-libgsm --enable-libvorb is --enable-libtheora --enable-libspeex --enable-libmp3lame --enable-libopenjpeg --enable-libschroedinger --enable-libopencore_amrwb --enable-libopencore_amrnb --enable-libvpx --disable-decoder=libvpx --arch=x86 --enable-runtime-cpudetect - -enable-libxvid --enable-libx264 --enable-librtmp --extra-libs='-lrtmp -lpolarss l -lws2_32 -lwinmm' --target-os=mingw32 --enable-avisynth --enable-w32threads -- cross-prefix=i686-mingw32- --cc='ccache i686-mingw32-gcc' --enable-memalign-hack libavutil 50.36. 0 / 50.36. 0 libavcore 0.16. 1 / 0.16. 1 libavcodec 52.108. 0 / 52.108. 0 libavformat 52.93. 0 / 52.93. 0 libavdevice 52. 2. 3 / 52. 2. 3 libavfilter 1.74. 0 / 1.74. 0 libswscale 0.12. 0 / 0.12. 0 Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'new.mp4': Metadata: major_brand : isom minor_version : 512 compatible_brands: isomiso2mp41 creation_time : 1970-01-01 00:00:00 encoder : Lavf52.93.0 Duration: 00:00:29.66, start: 0.000000, bitrate: 193 kb/s Stream #0.0(und): Video: mpeg4, yuv420p, 200x134 [PAR 1:1 DAR 100:67], 192 k b/s, 15 fps, 15 tbr, 15 tbn, 15 tbc Metadata: creation_time : 1970-01-01 00:00:00 [wav @ 01fed010] max_analyze_duration reached Input #1, wav, from 'lotr.wav': Duration: 00:00:29.90, bitrate: 176 kb/s Stream #1.0: Audio: pcm_s16le, 11025 Hz, 1 channels, s16, 176 kb/s File 'new_w_audio.mp4' already exists. Overwrite ? [y/N] y [buffer @ 01b03820] w:200 h:134 pixfmt:yuv420p Output #0, mp4, to 'new_w_audio.mp4': Metadata: major_brand : isom minor_version : 512 compatible_brands: isomiso2mp41 creation_time : 1970-01-01 00:00:00 encoder : Lavf52.93.0 Stream #0.0(und): Video: mpeg4, yuv420p, 200x134 [PAR 1:1 DAR 100:67], q=2-3 1, 200 kb/s, 15 tbn, 15 tbc Metadata: creation_time : 1970-01-01 00:00:00 Stream #0.1: Audio: aac, 11025 Hz, 1 channels, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #1.0 -> #0.1 Press [q] to stop encoding

  Read the article

• Tuning Linux IP routing parameters -- secret_interval and tcp_mem

  - by Jeff Atwood

  We had a little failover problem with one of our HAProxy VMs today. When we dug into it, we found this: Jan 26 07:41:45 haproxy2 kernel: [226818.070059] __ratelimit: 10 callbacks suppressed Jan 26 07:41:45 haproxy2 kernel: [226818.070064] Out of socket memory Jan 26 07:41:47 haproxy2 kernel: [226819.560048] Out of socket memory Jan 26 07:41:49 haproxy2 kernel: [226822.030044] Out of socket memory Which, per this link, apparently has to do with low default settings for net.ipv4.tcp_mem. So we increased them by 4x from their defaults (this is Ubuntu Server, not sure if the Linux flavor matters): current values are: 45984 61312 91968 new values are: 183936 245248 367872 After that, we started seeing a bizarre error message: Jan 26 08:18:49 haproxy1 kernel: [ 2291.579726] Route hash chain too long! Jan 26 08:18:49 haproxy1 kernel: [ 2291.579732] Adjust your secret_interval! Shh.. it's a secret!! This apparently has to do with /proc/sys/net/ipv4/route/secret_interval which defaults to 600 and controls periodic flushing of the route cache The secret_interval instructs the kernel how often to blow away ALL route hash entries regardless of how new/old they are. In our environment this is generally bad. The CPU will be busy rebuilding thousands of entries per second every time the cache is cleared. However we set this to run once a day to keep memory leaks at bay (though we've never had one). While we are happy to reduce this, it seems odd to recommend dropping the entire route cache at regular intervals, rather than simply pushing old values out of the route cache faster. After some investigation, we found /proc/sys/net/ipv4/route/gc_elasticity which seems to be a better option for keeping the route table size in check: gc_elasticity can best be described as the average bucket depth the kernel will accept before it starts expiring route hash entries. This will help maintain the upper limit of active routes. We adjusted elasticity from 8 to 4, in the hopes of the route cache pruning itself more aggressively. The secret_interval does not feel correct to us. But there are a bunch of settings and it's unclear which are really the right way to go here. /proc/sys/net/ipv4/route/gc_elasticity (8) /proc/sys/net/ipv4/route/gc_interval (60) /proc/sys/net/ipv4/route/gc_min_interval (0) /proc/sys/net/ipv4/route/gc_timeout (300) /proc/sys/net/ipv4/route/secret_interval (600) /proc/sys/net/ipv4/route/gc_thresh (?) rhash_entries (kernel parameter, default unknown?) We don't want to make the Linux routing worse, so we're kind of afraid to mess with some of these settings. Can anyone advise which routing parameters are best to tune, for a high traffic HAProxy instance?

  Read the article

• Cannot run a VM with more than three network interfaces with KVM

  - by Bostonvaulter

  I'm running KVM on top of Ubuntu 10.10 Server I can create VM's (Virtual Machine) and network interfaces fine but I cannot seem to add more than three network interfaces. As soon as I have a VM with four network interfaces it gets stuck on startup at the starting SeaBIOS page with this message: Starting SeaBIOS (version pre-0.6.1-20100702_143500-palmer) So far I've verified this with two VM's, a Ubuntu 10.10 desktop and a Vyatta router. The specific network hardware I assign to the VM's doesn't seem to matter. I'm trying to have one bridged interface and three private networks using Vyatta to route between them. Does anyone know why I can't run a VM with more than three network interfaces? Edit: Additionally the KVM thread responsible for the specific VM hangs using ~100% CPU (i.e. one core). Here's the command for the process that is hanging: /usr/bin/kvm -S -M pc-0.12 -enable-kvm -m 512 -smp 1,sockets=1,cores=1,threads=1 -name vyatta -uuid 6dff7c94-6810-423e-5fea-fec10da0e9b7 -nodefaults -chardev socket,id=monitor,path=/var/lib/libvirt/qemu/vyatta.monitor,server,nowait -mon chardev=monitor,mode=readline -rtc base=utc -boot c -drive file=/home/rams/virtual-machines/vyatta.img,if=none,id=drive-ide0-0-0,boot=on,format=raw -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0 -drive if=none,media=cdrom,id=drive-ide0-1-0,readonly=on,format=raw -device ide-drive,bus=ide.1,unit=0,drive=drive-ide0-1-0,id=ide0-1-0 -device rtl8139,vlan=0,id=net0,mac=00:54:00:be:cc:4b,bus=pci.0,addr=0x3 -net tap,fd=97,vlan=0,name=hostnet0 -device rtl8139,vlan=1,id=net1,mac=52:54:00:da:59:ed,bus=pci.0,addr=0x5 -net tap,fd=98,vlan=1,name=hostnet1 -device rtl8139,vlan=2,id=net2,mac=52:54:00:ce:22:b6,bus=pci.0,addr=0x6 -net tap,fd=99,vlan=2,name=hostnet2 -device rtl8139,vlan=3,id=net3,mac=52:54:00:1e:bc:46,bus=pci.0,addr=0x7 -net tap,fd=101,vlan=3,name=hostnet3 -chardev pty,id=serial0 -device isa-serial,chardev=serial0 -usb -vnc 127.0.0.1:0 -k en-us -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x4 Edit: I've also found an error in dmesg that might be related (it also shows up when running virtd in verbose mode): 14:47:24.399: warning : qemudParsePCIDeviceStrs:1422 : Unexpected exit status '1', qemu probably failed I've also tried disabling app armor but that doesn't seem to make a difference.

  Read the article

• Error Installing ruby with RVM Single User mode on Arch Linux

  - by ChrisBurnor

  I've just installed RVM on ArchLinux x64 in single user mode via the recommended install script curl -L https://get.rvm.io | bash -s stable I've also installed all the requirements listed in rvm requirements However, I'm having trouble actually installing any version of ruby. And getting the following error: arch:~ % rvm install 1.9.3 No binary rubies available for: ///ruby-1.9.3-p194. Continuing with compilation. Please read 'rvm mount' to get more information on binary rubies. Fetching yaml-0.1.4.tar.gz to /home/christopher/.rvm/archives % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 460k 100 460k 0 0 702k 0 --:--:-- --:--:-- --:--:-- 767k Extracting yaml-0.1.4.tar.gz to /home/christopher/.rvm/src Prepare yaml in /home/christopher/.rvm/src/yaml-0.1.4. Configuring yaml in /home/christopher/.rvm/src/yaml-0.1.4. Error running ' ./configure --prefix=/home/christopher/.rvm/usr ', please read /home/christopher/.rvm/log/ruby-1.9.3-p194/yaml/configure.log Compiling yaml in /home/christopher/.rvm/src/yaml-0.1.4. Error running 'make', please read /home/christopher/.rvm/log/ruby-1.9.3-p194/yaml/make.log Please note that it's required to reinstall all rubies: rvm reinstall all --force Installing Ruby from source to: /home/christopher/.rvm/rubies/ruby-1.9.3-p194, this may take a while depending on your cpu(s)... ruby-1.9.3-p194 - #downloading ruby-1.9.3-p194, this may take a while depending on your connection... ruby-1.9.3-p194 - #extracting ruby-1.9.3-p194 to /home/christopher/.rvm/src/ruby-1.9.3-p194 ruby-1.9.3-p194 - #extracted to /home/christopher/.rvm/src/ruby-1.9.3-p194 Skipping configure step, 'configure' does not exist, did autoreconf not run successfully? ruby-1.9.3-p194 - #compiling Error running 'make', please read /home/christopher/.rvm/log/ruby-1.9.3-p194/make.log There has been an error while running make. Halting the installation. The log files are as follows: arch:~ % cat ~/.rvm/log/ruby-1.9.3-p194/yaml/configure.log __rvm_log_command:32: permission denied: arch:~ % cat ~/.rvm/log/ruby-1.9.3-p194/yaml/make.log make: *** No targets specified and no makefile found. Stop. arch:~ % cat ~/.rvm/log/ruby-1.9.3-p194/make.log make: *** No targets specified and no makefile found. Stop.

  Read the article

• NRPE Warning threshold must be a positive integer

  - by Frida

  OS: Ubuntu 12.10 Server 64bits I've installed Icinga, with ido2db, pnp4nagios and icinga-web (last release, following the instruction given in the documentation, installation with apt, etc). I am using icinga-web to monitor my hosts. For the moment, I have just my localhost, and all is perfect. I am trying to add a host and monitor it with NRPE (version 2.12): root@server:/etc/icinga# /usr/lib/nagios/plugins/check_nrpe -H client NRPE v2.12 The configuration looks good. I've created a file in /etc/icinga/objects/client.cfg as below on the server: root@server:/etc/icinga/objects# cat client.cfg define host{ use generic-host ; Name of host template to use host_name client alias client.toto address xx.xx.xx.xx } # Service Definitions define service{ use generic-service host_name client service_description CPU Load check_command check_nrpe_1arg!check_load } define service{ use generic-service host_name client service_description Number of Users check_command check_nrpe_1arg!check_users } And add in my /etc/icinga/commands.cfg: # this command runs a program $ARG1$ with no arguments define command { command_name check_nrpe command_line /usr/lib/nagios/plugins/check_nrpe -H $HOSTADDRESS$ -c $ARG1$ -a $ARG2$ } # this command runs a program $ARG1$ with no arguments define command { command_name check_nrpe_1arg command_line /usr/lib/nagios/plugins/check_nrpe -H $HOSTADDRESS$ -c $ARG1$ } But it does not work. These are the logs from the client: Dec 3 19:45:12 client nrpe[604]: Connection from xx.xx.xx.xx port 32641 Dec 3 19:45:12 client nrpe[604]: Host address is in allowed_hosts Dec 3 19:45:12 client nrpe[604]: Handling the connection... Dec 3 19:45:12 client nrpe[604]: Host is asking for command 'check_users' to be run... Dec 3 19:45:12 client nrpe[604]: Running command: /usr/lib/nagios/plugins/check_users -w -c Dec 3 19:45:12 client nrpe[604]: Command completed with return code 3 and output: check_users: Warning t hreshold must be a positive integer#012Usage:check_users -w -c Dec 3 19:45:12 client nrpe[604]: Return Code: 3, Output: check_users: Warning threshold must be a positive integer#012Usage:check_users -w -c Dec 3 19:44:49 client nrpe[32582]: Connection from xx.xx.xx.xx port 32129 Dec 3 19:44:49 client nrpe[32582]: Host address is in allowed_hosts Dec 3 19:44:49 client nrpe[32582]: Handling the connection... Dec 3 19:44:49 client nrpe[32582]: Host is asking for command 'check_load' to be run... Dec 3 19:44:49 client nrpe[32582]: Running command: /usr/lib/nagios/plugins/check_load -w -c Dec 3 19:44:49 client nrpe[32582]: Command completed with return code 3 and output: Warning threshold mu st be float or float triplet!#012#012Usage:check_load [-r] -w WLOAD1,WLOAD5,WLOAD15 -c CLOAD1,CLOAD5,CLO AD15 Dec 3 19:44:49 client nrpe[32582]: Return Code: 3, Output: Warning threshold must be float or float trip let!#012#012Usage:check_load [-r] -w WLOAD1,WLOAD5,WLOAD15 -c CLOAD1,CLOAD5,CLOAD15 Dec 3 19:44:49 client nrpe[32582]: Connection from xx.xx.xx.xx closed. Have you any ideas?

  Read the article

• HT Link Sync Error after Ubuntu 10.04 LTS Installation

  - by marklab

  Update 1 I just assembled an exact replica of this server, and successfully installed Ubuntu 10.04 LTS in a RAID10 configuration. The success was confirmed by a login to the initial account. There must be a hardware component that is faulty. Since the error mentions HT, which I believe to be Hyper Threading, I will start with the CPUs. Please indicate if this error is more strongly associated with any other piece of hardware. Or make a recommendation of another approach that would be good for this issue. Issue I was attempting to install Ubuntu 10.04 LTS on this system with the board RAID10 configured. However, the installation failed at the partitioning stage by rebooting the system. Upon reboot, there is an error report after POST listing the following: Node0: NB WatchDog Timer Error Node1: HT Link Sync Error Node2: HT Link Sync Error ... Node7: HT Link Sync Error Press F1 to continue/resume. After pressing F1 the system will boot from the Ubuntu 10.04 LTS installation disc. However, it will fail at the same stage, and go through the same process from there. Hardware CPU: AMD OPTERON X12 6172 G34 2.1G 18MB Motherboard: Supermicro H8QG6-F HDD: WD Caviar Green 2TB 5.4K RPM Troubleshooting I disabled RAID10 on the system, and installed the Ubuntu on a single drive. It installed successfully. I then went back to a RAID10 setup and attempted to install on the system again, and was able to make it through the partitioning stage. However, upon reboot, the system reported: Error: file not found, and then booted me into the Grub Rescue console. I feel I have aggravated the problem at this point because when I attempted to install from the boot disc again, the system reboots upon hitting enter to even start the installation process. It does the same thing when trying to boot from an Ubuntu 11 disc. I have not been able to find any information on this HT Link Sync Error, which I feel may have started the problems I am experiencing now with the installation of the OS. I am also aware that Ubuntu is said not to be supported by the motherboard according to Supermicro's site. However, since I was able to install it successfully on a single drive, I do not believe it is incompatible. I would like to know a reason for why it's failing to install on/off.

  Read the article

• Low framerate on background apps

  - by user1698923

  My problem is that when a game is running in the foreground, in Full Screen mode, any applications on my second monitor (such as youtube videos, videos, not app specific) drop their frame-rate to about 2-3 FPS. It seems like some sort of power management option that I can't track down. As far as I can tell, it's not due to the GPU not being able to keep up. For instance, my PC can play League of Legends at about 280FPS when the framerate is uncapped. If i cap it at 60FPS using the in-game option, it has no affect on the performance of the background app. Summary Operating System Windows 8 Pro 64-bit CPU Intel Core i7 3820 @ 3.60GHz 42 °C Sandy Bridge-E 32nm Technology RAM 12.0GB Triple-Channel DDR3 @ 533MHz (7-7-7-20) Motherboard Gigabyte Technology Co., Ltd. X79-UD3 (SOCKET 0) 37 °C Graphics DELL U2713HM (2560x1440@59Hz) DELL U2713HM (2560x1440@59Hz) 1280MB NVIDIA GeForce GTX 570 (Gigabyte) 58 °C Hard Drives 212GB Volume0 (RAID) 1863GB Western Digital WDC WD20EARS-00MVWB0 (SATA) 36 °C 1863GB Western Digital WDC WD20EARS-00MVWB0 (SATA) 34 °C Optical Drives No optical disk drives detected Audio ASUS Xonar Essence STX Audio Device Operating System Windows 8 Pro 64-bit Computer type: Desktop Graphics Monitor 1 Name DELL U2713HM on NVIDIA GeForce GTX 570 Current Resolution 2560x1440 pixels Work Resolution 2560x1400 pixels State Enabled, Output devices support Multiple displays Extended, Secondary, Enabled Monitor Width 2560 Monitor Height 1440 Monitor BPP 32 bits per pixel Monitor Frequency 59 Hz Device \\.\DISPLAY4\Monitor0 Monitor 2 Name DELL U2713HM on NVIDIA GeForce GTX 570 Current Resolution 2560x1440 pixels Work Resolution 2560x1400 pixels State Enabled, Output devices support Multiple displays Extended, Primary, Enabled Monitor Width 2560 Monitor Height 1440 Monitor BPP 32 bits per pixel Monitor Frequency 59 Hz Device \\.\DISPLAY5\Monitor0 NVIDIA GeForce GTX 570 Manufacturer NVIDIA Model GeForce GTX 570 GPU GF110 Device ID 10DE-1086 Revision A2 Subvendor Gigabyte (1458) Series GeForce GTX 500 Current Performance Level Level 3 Current GPU Clock 845 MHz Current Memory Clock 1900 MHz Current Shader Clock 1690 MHz Voltage 0.988 V Technology 40 nm Die Size 520 mm² Release Date Dec 07, 2010 DirectX Support 11.0 OpenGL Support 5.0 Bus Interface PCI Express x16 Temperature 57 °C Driver version 9.18.13.2018 BIOS Version 70.10.55.00.01 ROPs 40 Shaders 512 unified Memory Type GDDR5 Memory 1280 MB Bus Width 64x5 (320 bit) Filtering Modes 16x Anisotropic Noise Level Moderate Max Power Draw 219 Watts Count of performance levels : 3 Level 1 - "Default" GPU Clock 50 MHz Memory Clock 135 MHz Shader Clock 101 MHz Level 2 - "2D Desktop" GPU Clock 405 MHz Memory Clock 324 MHz Shader Clock 810 MHz Level 3 - "3D Applications" GPU Clock 845 MHz Memory Clock 1900 MHz Shader Clock 1690 MHz Things I've tried: 1) Updating the graphics driver 2) Setting windows power mode to High Performance 3) Reset Nvidia Global Performance settings to default

  Read the article

• gunicorn + django + nginx unix://socket failed (11: Resource temporarily unavailable)

  - by user1068118

  Running very high volume traffic on these servers configured with django, gunicorn, supervisor and nginx. But a lot of times I tend to see 502 errors. So I checked the nginx logs to see what error and this is what is recorded: [error] 2388#0: *208027 connect() to unix:/tmp/gunicorn-ourapp.socket failed (11: Resource temporarily unavailable) while connecting to upstream Can anyone help debug what might be causing this to happen? This is our nginx configuration: sendfile on; tcp_nopush on; tcp_nodelay off; listen 80 default_server; server_name imp.ourapp.com; access_log /mnt/ebs/nginx-log/ourapp-access.log; error_log /mnt/ebs/nginx-log/ourapp-error.log; charset utf-8; keepalive_timeout 60; client_max_body_size 8m; gzip_types text/plain text/xml text/css application/javascript application/x-javascript application/json; location / { proxy_pass http://unix:/tmp/gunicorn-ourapp.socket; proxy_pass_request_headers on; proxy_read_timeout 600s; proxy_connect_timeout 600s; proxy_redirect http://localhost/ http://imp.ourapp.com/; #proxy_set_header Host $host; #proxy_set_header X-Real-IP $remote_addr; #proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; #proxy_set_header X-Forwarded-Proto $my_scheme; #proxy_set_header X-Forwarded-Ssl $my_ssl; } We have configure Django to run in Gunicorn as a generic WSGI application. Supervisord is used to launch the gunicorn workers: home/user/virtenv/bin/python2.7 /home/user/virtenv/bin/gunicorn --config /home/user/shared/etc/gunicorn.conf.py daggr.wsgi:application This is what the gunicorn.conf.py looks like: import multiprocessing bind = 'unix:/tmp/gunicorn-ourapp.socket' workers = multiprocessing.cpu_count() * 3 + 1 timeout = 600 graceful_timeout = 40 Does anyone know where I can start digging to see what might be causing the problem? This is what my ulimit -a output looks like on the server: core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 0 file size (blocks, -f) unlimited pending signals (-i) 59481 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) unlimited open files (-n) 50000 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) 1024 virtual memory (kbytes, -v) unlimited file locks (-x) unlimited

  Read the article

• How to diagnose repeated "Starting up database '<dbname>'"

  - by Richard Slater

  I have a SQL 2008 server which is predominantly used as a development server, in the last two weeks it has been having occasional "fits", I have isolated the cause of these fits as CHECKDB being run almost continuiously, the following log information is logged to the Windows Event Log (Source: MSSQLSERVER, Category: Server): Event: 1073758961, Message: Starting up database 'DBName1'. Event: 1073758961, Message: Starting up database 'DBName2'. Event: 1073759397, Message: CHECKDB for database 'DBName1' finished without errors on 2010-07-19 20:29:26.993 (local time). This is an informational message only; no user action is required. Event: 1073759397, Message: CHECKDB for database 'DBName1' finished without errors on 2010-07-19 20:29:26.993 (local time). This is an informational message only; no user action is required. This is repeated every 1-2 seconds untill SQL Server is restarted or the offending databases are detatched. I initially thought that it was a problem with the databases so I took a backup and restored them to a SQL Express instance, all of the data is in tact, and CHECKDB runs without problem. The two databases that were causing a problem last week were not being used; so I took full backups of them and detached the databases, this resolved the problem. However at 0100 GMT this morning to other totally unrelated databases started showing the same problems. There is nothing in the event log to suggest that something happened to the server such as a restart, there are no messages about processes crashing or issues being detected with the storage controller. Speaking to the owner of the company this computer has suffered from "gremlins" in the past, however advice was taken and the motherboard was replaced and the computer rebuilt, memory and processor are the same. Stats: O/S: Windows 2008 Standard Build 6002 CPU: 2x Pentium Dual-Core E5200 @ 2.5GHz RAM: 2GB SQL: 2008 Standard 10.0.2531 Edit: someone posted then deleted a comment about AutoClose, it was turned on on the databases affected. It seems that best practice is to disable it so I have done that with the folllowing. EXECUTE sp_MSforeachdb 'IF (''?'' NOT IN (''master'', ''tempdb'', ''msdb'', ''model'')) EXECUTE (''ALTER DATABASE [?] SET AUTO_CLOSE OFF WITH NO_WAIT'')' I won't know if the problem recurs for some time so I am still open to further answers.

  Read the article

• Elasticsearch won't start anymore

  - by Oleander

  I restarted my elasticsearch instance 5 days ago and I haven't manage to start it since then. I get no output in the log file /var/log/elasticsearch/ nor does the elasticsearch binary print any information when running at using elasticsearch -f. I once manage to get this output. [2012-11-15 22:51:18,427][INFO ][node ] [Piper] {0.19.11}[29584]: initializing ... [2012-11-15 22:51:18,433][INFO ][plugins ] [Piper] loaded [], sites [] Running curl http://localhost:9200 resulted in curl: (7) couldn't connect to host. I've tried increasing the memory from 3gb to 10gb, but that didn't make any diffrence. Running /etc/init.d/elasticsearch start takes 30 seconds. ps aux | grep elasticsearch results in this output. /usr/local/share/elasticsearch/bin/service/exec/elasticsearch-linux-x86-64 /usr/local/share/elasticsearch/bin/service/elasticsearch.conf wrapper.syslog.ident=elasticsearch wrapper.pidfile=/usr/local/share/elasticsearch/bin/service/./elasticsearch.pid wrapper.name=elasticsearch wrapper.displayname=ElasticSearch wrapper.daemonize=TRUE wrapper.statusfile=/usr/local/share/elasticsearch/bin/service/./elasticsearch.status wrapper.java.statusfile=/usr/local/share/elasticsearch/bin/service/./elasticsearch.java.status wrapper.script.version=3.5.14 /usr/lib/jvm/java-7-openjdk-amd64/jre/bin/java -Delasticsearch-service -Des.path.home=/usr/local/share/elasticsearch -Xss256k -XX:+UseParNewGC -XX:+UseConcMarkSweepGC -XX:CMSInitiatingOccupancyFraction=75 -XX:+UseCMSInitiatingOccupancyOnly -XX:+HeapDumpOnOutOfMemoryError -Djava.awt.headless=true -Xms1024m -Xmx1024m -Djava.library.path=/usr/local/share/elasticsearch/bin/service/lib -classpath /usr/local/share/elasticsearch/bin/service/lib/wrapper.jar:/usr/local/share/elasticsearch/lib/elasticsearch-0.19.11.jar:/usr/local/share/elasticsearch/lib/elasticsearch-0.19.11.jar:/usr/local/share/elasticsearch/lib/jna-3.3.0.jar:/usr/local/share/elasticsearch/lib/log4j-1.2.17.jar:/usr/local/share/elasticsearch/lib/lucene-analyzers-3.6.1.jar:/usr/local/share/elasticsearch/lib/lucene-core-3.6.1.jar:/usr/local/share/elasticsearch/lib/lucene-highlighter-3.6.1.jar:/usr/local/share/elasticsearch/lib/lucene-memory-3.6.1.jar:/usr/local/share/elasticsearch/lib/lucene-queries-3.6.1.jar:/usr/local/share/elasticsearch/lib/snappy-java-1.0.4.1.jar:/usr/local/share/elasticsearch/lib/sigar/sigar-1.6.4.jar -Dwrapper.key=k7r81VpK3_Bb3N_5 -Dwrapper.port=32000 -Dwrapper.jvm.port.min=31000 -Dwrapper.jvm.port.max=31999 -Dwrapper.disable_console_input=TRUE -Dwrapper.pid=23888 -Dwrapper.version=3.5.14 -Dwrapper.native_library=wrapper -Dwrapper.service=TRUE -Dwrapper.cpu.timeout=10 -Dwrapper.jvmid=1 org.tanukisoftware.wrapper.WrapperSimpleApp org.elasticsearch.bootstrap.ElasticSearchF My current system: ElasticSearch Version: 0.19.11, JVM: 23.2-b09 Ubuntu 12.04 LTS I've tried re-install elasticsearch, removing old directories. Why can't I get it to start?

  Read the article

• Django + gunicorn + virtualenv + Supervisord issue

  - by Florian Le Goff

  Dear all, I have a strange issue with my virtualenv + gunicorn setup, only when gunicorn is launched via supervisord. I do realize that it may very well be an issue with my supervisord and I would appreciate any feedback on a better place to ask for help... In a nutshell : when I run gunicorn from my user shell, inside my virtualenv, everything is working flawlessly. I'm able to access all the views of my Django project. When gunicorn is launched by supervisord at the system startup, everything is OK. But, if I have to kill the gunicorn_django processes, or if I perform a supervisord restart, once that gunicorn_django has relaunched, every request is answered with a weird Traceback : (...) File "/home/hc/prod/venv/lib/python2.6/site-packages/Django-1.2.5-py2.6.egg/django/db/__init__.py", line 77, in connection = connections[DEFAULT_DB_ALIAS] File "/home/hc/prod/venv/lib/python2.6/site-packages/Django-1.2.5-py2.6.egg/django/db/utils.py", line 92, in __getitem__ backend = load_backend(db['ENGINE']) File "/home/hc/prod/venv/lib/python2.6/site-packages/Django-1.2.5-py2.6.egg/django/db/utils.py", line 50, in load_backend raise ImproperlyConfigured(error_msg) TemplateSyntaxError: Caught ImproperlyConfigured while rendering: 'django.db.backends.postgresql_psycopg2' isn't an available database backend. Try using django.db.backends.XXX, where XXX is one of: 'dummy', 'mysql', 'oracle', 'postgresql', 'postgresql_psycopg2', 'sqlite3' Error was: cannot import name utils Full stack available here : http://pastebin.com/BJ5tNQ2N I'm running... Ubuntu/maverick (up-to-date) Python = 2.6.6 virtualenv = 1.5.1 gunicorn = 0.12.0 Django = 1.2.5 psycopg2 = '2.4-beta2 (dt dec pq3 ext)' gunicorn configuration : backlog = 2048 bind = "127.0.0.1:8000" pidfile = "/tmp/gunicorn-hc.pid" daemon = True debug = True workers = 3 logfile = "/home/hc/prod/log/gunicorn.log" loglevel = "info" supervisord configuration : [program:gunicorn] directory=/home/hc/prod/hc command=/home/hc/prod/venv/bin/gunicorn_django -c /home/hc/prod/hc/gunicorn.conf.py user=hc umask=022 autostart=True autorestart=True redirect_stderr=True Any advice ? I've been stuck on this one for quite a while. It seems like some weird memory limit, as I'm not enforcing anything special : $ ulimit -a core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 20 file size (blocks, -f) unlimited pending signals (-i) 16382 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) unlimited open files (-n) 1024 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) unlimited virtual memory (kbytes, -v) unlimited file locks (-x) unlimited Thank you.

  Read the article

• Windows 7 x64 "upgrade" repair fails

  - by Polynomial

  I've been running into issues with Windows Update, which I can't seem to fix. The hotfixes don't work, nor does the Windows update readyness tool, or the manual SP1 upgrade. I get various esoteric errors which nobody seems to have a fix for. Looks like some of the update cache is corrupt and digital signatures seem to be broken on some packages / Windows Update components. Long story short, I have discovered the only option is to do a repair operation on the OS, to repair everything. It's so corrupt that only a complete replacement will fix it. According to various sources (including MSKB) one can perform a repair by running an in-place upgrade. I've got the Windows 7 Ultimate retail disc, which I've inserted into my machine. I ran setup.exe and went through in the following order: Install now Go online to get latest updates (I've also tried not getting updates) Wait for updates to be downloaded Select Windows 7 Ultimate (x64 architecture) and click next Accept the T&Cs, click next Click Upgrade At this point it spends a minute on the "checking compatibility" screen, after which I get the following error: The following issues are preventing Windows from upgrading. Cancel the upgrade, complete each task, and then restart the upgrade to continue. You can’t upgrade 64-bit Windows to a 32-bit version of Windows. To upgrade, obtain a 64-bit version of the installation disc, or go online to see how to install Windows 7 and keep your files and settings. 32-bit Windows cannot be upgraded to a 64-bit version of Windows. To upgrade, obtain a 32-bit version of the Windows installation disc. It also mentions a warning about potential conflicts with a storage driver and VS2010, but that doesn't seem to be the blocking issue. My currently installed version of Windows is Ultimate 64-bit (absolutely sure of this) and the disc is definitely a x86 / x64 combined Ultimate retail disc. There seem to be a few people who have run into this (e.g. this question), but I've not seen any answers. I've checked the event viewer, but can't spot anything in there that's related. Any idea how I can get this working? P.S: Just to pre-empt the inevitable "are you suuuuuuuuuuuuure it's x64 Ultimate?" questions:

  Read the article

• Torque jobs does not enter "E" state (unless "qrun")

  - by Vi.

  Jobs I add to the queue stays there in "Queued" state without attempts to be executed (unless I manually qrun them) /var/spool/torque/server_logs say just 04/11/2011 12:43:27;0100;PBS_Server;Job;16.localhost;enqueuing into batch, state 1 hop 1 04/11/2011 12:43:27;0008;PBS_Server;Job;16.localhost;Job Queued at request of test@localhost, owner = test@localhost, job name = Qqq, queue = batch The job requires just 1 CPU on 1 node. # qmgr -c "list queue batch" Queue batch queue_type = Execution total_jobs = 0 state_count = Transit:0 Queued:0 Held:0 Waiting:0 Running:0 Exiting:0 max_running = 3 acl_host_enable = True acl_hosts = localhost resources_min.ncpus = 1 resources_min.nodect = 1 resources_default.ncpus = 1 resources_default.nodes = 1 resources_default.walltime = 00:00:10 mtime = Mon Apr 11 12:07:10 2011 resources_assigned.ncpus = 0 resources_assigned.nodect = 0 kill_delay = 3 enabled = True started = True I can't set resources_assigned to nonzero because of Cannot set attribute, read only or insufficient permission resources_assigned.ncpus. When I qrun some task, this goes to mom's log: 04/11/2011 21:27:48;0001; pbs_mom;Svr;pbs_mom;LOG_DEBUG::mom_checkpoint_job_has_checkpoint, FALSE 04/11/2011 21:27:48;0001; pbs_mom;Job;TMomFinalizeJob3;job 18.localhost started, pid = 28592 04/11/2011 21:27:48;0080; pbs_mom;Job;18.localhost;scan_for_terminated: job 18.localhost task 1 terminated, sid=28592 04/11/2011 21:27:48;0008; pbs_mom;Job;18.localhost;job was terminated 04/11/2011 21:27:48;0080; pbs_mom;Svr;preobit_reply;top of preobit_reply 04/11/2011 21:27:48;0080; pbs_mom;Svr;preobit_reply;DIS_reply_read/decode_DIS_replySvr worked, top of while loop 04/11/2011 21:27:48;0080; pbs_mom;Svr;preobit_reply;in while loop, no error from job stat 04/11/2011 21:27:48;0080; pbs_mom;Job;18.localhost;obit sent to server Scheduler log (/var/spool/torque/sched_logs/20110705): 07/05/2011 21:44:53;0002; pbs_sched;Svr;Log;Log opened 07/05/2011 21:44:53;0002; pbs_sched;Svr;TokenAct;Account file /var/spool/torque/sched_priv/accounting/20110705 opened 07/05/2011 21:44:53;0002; pbs_sched;Svr;main;/usr/sbin/pbs_sched startup pid 16234 qstat -f: Job Id: 26.localhost Job_Name = qwe Job_Owner = test@localhost job_state = Q queue = batch server = localhost Checkpoint = u ctime = Tue Jul 5 21:43:31 2011 Error_Path = localhost:/home/test/jscfi/default/0.738784810485275/qwe.e26 Hold_Types = n Join_Path = n Keep_Files = n Mail_Points = a mtime = Tue Jul 5 21:43:31 2011 Output_Path = localhost:/home/test/jscfi/default/0.738784810485275/qwe.o26 Priority = 0 qtime = Tue Jul 5 21:43:31 2011 Rerunable = True Resource_List.ncpus = 1 Resource_List.neednodes = 1:ppn=1 Resource_List.nodect = 1 Resource_List.nodes = 1:ppn=1 Resource_List.walltime = 00:01:00 substate = 10 Variable_List = PBS_O_HOME=/home/test,PBS_O_LANG=en_US.UTF-8, PBS_O_LOGNAME=test, PBS_O_PATH=/usr/local/bin:/usr/bin:/bin:/usr/bin/X11:/usr/games, PBS_O_MAIL=/var/mail/test,PBS_O_SHELL=/bin/sh,PBS_SERVER=127.0.0.1, PBS_O_WORKDIR=/home/test/jscfi/default/0.738784810485275, PBS_O_QUEUE=batch,PBS_O_HOST=localhost euser = test egroup = test queue_rank = 1 queue_type = E etime = Tue Jul 5 21:43:31 2011 submit_args = run.pbs Walltime.Remaining = 6 fault_tolerant = False How to make it execute jobs automatically, without manual qrun?

  Read the article

• How to install 32-bit libraries using Debian Testing

  - by bgoodr

  Question: What is the way to determine, ahead of time and without doing a full install of 64-bit Debian Testing NETINST, when Debian Testing has 32-bit libraries available and fully working and installable so that the following command works without broken package errors?: apt-get install ia32-libs ia32-libs-gtk The errors that occur when 32-bit libraries are not available, still in some broken state, or whatever is broken are detailed below. I already have concluded that "Just install Stable" is my stop-gap measure for now, but I would like to know the answer to the above question so as to avoid a lengthy installation process only to run into these problems at the very end. Details: I downloaded the 64-bit Debian Testing netinst a couple of days ago. This was "Jessie" built 20131014-06:07 via http://tinyurl.com/lejpa. This is weekly testing build. Yes, I know I should expect problems, and I did. I managed to get it completely installed and was able to invoke into GNOME, but not get past the 32-bit library problem. The problems starts when I attempt to install the 32-bit libraries via: apt-get install ia32-libs ia32-libs-gtk that returns: root@breath:~# apt-get install ia32-libs ia32-libs-gtk Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: ia32-libs : Depends: ia32-libs-i386 but it is not installable ia32-libs-gtk : Depends: ia32-libs-i386 but it is not installable Depends: ia32-libs-gtk-i386 but it is not installable E: Unable to correct problems, you have held broken packages. I then found an old (2012 is old to me) answer at ia32-libs : Depends: ia32-libs-i386 but it is not installable and even tried what they suggested there which was dpkg --add-architecture i386 apt-get update After executing the above, I tried again but got: root@breath:~# apt-get install ia32-libs ia32-libs-gtk Reading package lists... Done Building dependency tree Reading state information... Done Some packages could not be installed. This may mean that you have requested an impossible situation or if you are using the unstable distribution that some required packages have not yet been created or been moved out of Incoming. The following information may help to resolve the situation: The following packages have unmet dependencies: ia32-libs : Depends: ia32-libs-i386 ia32-libs-gtk : Depends: ia32-libs-i386 E: Unable to correct problems, you have held broken packages. root@breath:~# And then tried this: root@breath:~# dpkg --get-selections | grep hold And that returned nothing. Not only is there broken packages, the system doesn't even know what packages are broken, so Debian Stable is my only solution I know of right now. Hence my question above.

  Read the article

• Is dual-booting an OS more or less secure than running a virtual machine?

  - by Mark

  I run two operating systems on two separate disk partitions on the same physical machine (a modern MacBook Pro). In order to isolate them from each other, I've taken the following steps: Configured /etc/fstab with ro,noauto (read-only, no auto-mount) Fully encrypted each partition with a separate encryption key (committed to memory) Let's assume that a virus infects my first partition unbeknownst to me. I log out of the first partition (which encrypts the volume), and then turn off the machine to clear the RAM. I then un-encrypt and boot into the second partition. Can I be reasonably confident that the virus has not / cannot infect both partitions, or am I playing with fire here? I realize that MBPs don't ship with a TPM, so a boot-loader infection going unnoticed is still a theoretical possibility. However, this risk seems about equal to the risk of the VMWare/VirtualBox Hypervisor being exploited when running a guest OS, especially since the MBP line uses UEFI instead of BIOS. This leads to my question: is the dual-partitioning approach outlined above more or less secure than using a Virtual Machine for isolation of services? Would that change if my computer had a TPM installed? Background: Note that I am of course taking all the usual additional precautions, such as checking for OS software updates daily, not logging in as an Admin user unless absolutely necessary, running real-time antivirus programs on both partitions, running a host-based firewall, monitoring outgoing network connections, etc. My question is really a public check to see if I'm overlooking anything here and try to figure out if my dual-boot scheme actually is more secure than the Virtual Machine route. Most importantly, I'm just looking to learn more about security issues. EDIT #1: As pointed out in the comments, the scenario is a bit on the paranoid side for my particular use-case. But think about people who may be in corporate or government settings and are considering using a Virtual Machine to run services or applications that are considered "high risk". Are they better off using a VM or a dual-boot scenario as I outlined? An answer that effectively weighs any pros/cons to that trade-off is what I'm really looking for in an answer to this post. EDIT #2: This question was partially fueled by debate about whether a Virtual Machine actually protects a host OS at all. Personally, I think it does, but consider this quote from Theo de Raadt on the OpenBSD mailing list: x86 virtualization is about basically placing another nearly full kernel, full of new bugs, on top of a nasty x86 architecture which barely has correct page protection. Then running your operating system on the other side of this brand new pile of shit. You are absolutely deluded, if not stupid, if you think that a worldwide collection of software engineers who can't write operating systems or applications without security holes, can then turn around and suddenly write virtualization layers without security holes. -http://kerneltrap.org/OpenBSD/Virtualization_Security By quoting Theo's argument, I'm not endorsing it. I'm simply pointing out that there are multiple perspectives here, so I'm trying to find out more about the issue.

  Read the article

• How to set up dual quadro cards on RHEL 5.5?

  - by Alex J. Roberts

  I have a RHEL 5 workstation with 2 nvidia Quadro FX4500 cards, with one display attached to each card. After doing a clean install of RHEL 5.5, the second display doesnt work (it worked ok in RHEL 5.2). Neither separate X screens nor Xinerama are working. The kernel version is 2.6.18-194.el5 I've tried nvidia drivers 185.18.36 (the ones that i was using on 5.2) and the latest 260.19.36 and neither works. My xorg.conf is as follows: # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 1.0 (buildmeister@builder58) Fri Aug 14 18:34:43 PDT 2009 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 0 0 Screen 1 "Screen1" RightOf "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection Section "Files" FontPath "unix/:7100" EndSection Section "ServerFlags" Option "Xinerama" "1" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/input/mice" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from data in "/etc/sysconfig/keyboard" Identifier "Keyboard0" Driver "kbd" Option "XkbLayout" "us" Option "XkbModel" "pc105" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "DELL 3007WFP" HorizSync 49.3 - 98.5 VertRefresh 60.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor1" VendorName "Unknown" ModelName "DELL 3007WFP" HorizSync 49.3 - 98.5 VertRefresh 60.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro FX 4500" BusID "PCI:10:0:0" EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro FX 4500" BusID "PCI:129:0:0" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection And the Xorg Log: X Window System Version 7.1.1 Release Date: 12 May 2006 X Protocol Version 11, Revision 0, Release 7.1.1 Build Operating System: Linux 2.6.18-164.11.1.el5 x86_64 Red Hat, Inc. Current Operating System: Linux blur.svsdsde 2.6.18-194.el5 #1 SMP Tue Mar 16 21:52:39 EDT 2010 x86_64 Build Date: 06 March 2010 Build ID: xorg-x11-server 1.1.1-48.76.el5 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Module Loader present Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Fri Feb 18 09:52:08 2011 (==) Using config file: "/etc/X11/xorg.conf" (==) ServerLayout "Layout0" (**) |-->Screen "Screen0" (0) (**) | |-->Monitor "Monitor0" (**) | |-->Device "Device0" (**) |-->Screen "Screen1" (1) (**) | |-->Monitor "Monitor1" (**) | |-->Device "Device1" (**) |-->Input Device "Keyboard0" (**) |-->Input Device "Mouse0" (**) FontPath set to: unix/:7100 (==) RgbPath set to "/usr/share/X11/rgb" (==) ModulePath set to "/usr/lib64/xorg/modules" (**) Option "Xinerama" "1" (**) Xinerama: enabled (==) Max clients allowed: 512, resource mask: 0xfffff (II) Open ACPI successful (/var/run/acpid.socket) (II) Module ABI versions: X.Org ANSI C Emulation: 0.3 X.Org Video Driver: 1.0 X.Org XInput driver : 0.6 X.Org Server Extension : 0.3 X.Org Font Renderer : 0.5 (II) Loader running on linux (II) LoadModule: "bitmap" (II) Loading /usr/lib64/xorg/modules/fonts/libbitmap.so (II) Module bitmap: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.0.0 Module class: X.Org Font Renderer ABI class: X.Org Font Renderer, version 0.5 (II) Loading font Bitmap (II) LoadModule: "pcidata" (II) Loading /usr/lib64/xorg/modules/libpcidata.so (II) Module pcidata: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.0.0 ABI class: X.Org Video Driver, version 1.0 (++) using VT number 7 (II) PCI: PCI scan (all values are in hex) (II) PCI: 00:00:0: chip 10de,005e card 103c,1500 rev a3 class 05,80,00 hdr 00 (II) PCI: 00:01:0: chip 10de,0051 card 103c,1500 rev a3 class 06,01,00 hdr 80 (II) PCI: 00:01:1: chip 10de,0052 card 103c,1500 rev a2 class 0c,05,00 hdr 80 (II) PCI: 00:02:0: chip 10de,005a card 103c,1500 rev a2 class 0c,03,10 hdr 80 (II) PCI: 00:02:1: chip 10de,005b card 103c,1500 rev a3 class 0c,03,20 hdr 80 (II) PCI: 00:04:0: chip 10de,0059 card 103c,1500 rev a2 class 04,01,00 hdr 00 (II) PCI: 00:06:0: chip 10de,0053 card 103c,1500 rev f2 class 01,01,8a hdr 00 (II) PCI: 00:07:0: chip 10de,0054 card 103c,1500 rev f3 class 01,01,85 hdr 00 (II) PCI: 00:08:0: chip 10de,0055 card 103c,1500 rev f3 class 01,01,85 hdr 00 (II) PCI: 00:09:0: chip 10de,005c card 0000,0000 rev a2 class 06,04,01 hdr 01 (II) PCI: 00:0a:0: chip 10de,0057 card 103c,1500 rev a3 class 06,80,00 hdr 00 (II) PCI: 00:0e:0: chip 10de,005d card 0000,0000 rev a3 class 06,04,00 hdr 01 (II) PCI: 00:18:0: chip 1022,1100 card 0000,0000 rev 00 class 06,00,00 hdr 80 (II) PCI: 00:18:1: chip 1022,1101 card 0000,0000 rev 00 class 06,00,00 hdr 80 (II) PCI: 00:18:2: chip 1022,1102 card 0000,0000 rev 00 class 06,00,00 hdr 80 (II) PCI: 00:18:3: chip 1022,1103 card 0000,0000 rev 00 class 06,00,00 hdr 80 (II) PCI: 00:19:0: chip 1022,1100 card 0000,0000 rev 00 class 06,00,00 hdr 80 (II) PCI: 00:19:1: chip 1022,1101 card 0000,0000 rev 00 class 06,00,00 hdr 80 (II) PCI: 00:19:2: chip 1022,1102 card 0000,0000 rev 00 class 06,00,00 hdr 80 (II) PCI: 00:19:3: chip 1022,1103 card 0000,0000 rev 00 class 06,00,00 hdr 80 (II) PCI: 05:05:0: chip 104c,8023 card 103c,1500 rev 00 class 0c,00,10 hdr 00 (II) PCI: 0a:00:0: chip 10de,009d card 10de,02af rev a1 class 03,00,00 hdr 00 (II) PCI: End of PCI scan (II) PCI-to-ISA bridge: (II) Bus -1: bridge is at (0:1:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set) (II) Subtractive PCI-to-PCI bridge: (II) Bus 5: bridge is at (0:9:0), (0,5,5), BCTRL: 0x0206 (VGA_EN is cleared) (II) Bus 5 non-prefetchable memory range: [0] -1 0 0xf5000000 - 0xf50fffff (0x100000) MX[B] (II) PCI-to-PCI bridge: (II) Bus 10: bridge is at (0:14:0), (0,10,10), BCTRL: 0x000a (VGA_EN is set) (II) Bus 10 I/O range: [0] -1 0 0x00003000 - 0x00003fff (0x1000) IX[B] (II) Bus 10 non-prefetchable memory range: [0] -1 0 0xf3000000 - 0xf4ffffff (0x2000000) MX[B] (II) Bus 10 prefetchable memory range: [0] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[B] (II) Host-to-PCI bridge: (II) Bus 0: bridge is at (0:24:0), (0,0,10), BCTRL: 0x0008 (VGA_EN is set) (II) Bus 0 I/O range: [0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B] (II) Bus 0 non-prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x100000000) MX[B] (II) Bus 0 prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x100000000) MX[B] (--) PCI:*(10:0:0) nVidia Corporation Quadro FX 4500 rev 161, Mem @ 0xf3000000/24, 0xc0000000/28, 0xf4000000/24, I/O @ 0x3000/7 (II) Addressable bus resource ranges are [0] -1 0 0x00000000 - 0xffffffff (0x100000000) MX[B] [1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B] (II) OS-reported resource ranges: [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [5] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] (II) Active PCI resource ranges: [0] -1 0 0xf5000000 - 0xf5003fff (0x4000) MX[B] [1] -1 0 0xf5004000 - 0xf50047ff (0x800) MX[B] [...snipped... post too long] [28] -1 0 0x0000fb00 - 0x0000fbff (0x100) IX[B] [29] -1 0 0x00003000 - 0x0000307f (0x80) IX[B](B) (II) Active PCI resource ranges after removing overlaps: [0] -1 0 0xf5000000 - 0xf5003fff (0x4000) MX[B] [1] -1 0 0xf5004000 - 0xf50047ff (0x800) MX[B] [...snipped... post too long] [28] -1 0 0x0000fb00 - 0x0000fbff (0x100) IX[B] [29] -1 0 0x00003000 - 0x0000307f (0x80) IX[B](B) (II) OS-reported resource ranges after removing overlaps with PCI: [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [5] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] (II) All system resource ranges: [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [4] -1 0 0xf5000000 - 0xf5003fff (0x4000) MX[B] [5] -1 0 0xf5004000 - 0xf50047ff (0x800) MX[B] [6] -1 0 0xf5104000 - 0xf5104fff (0x1000) MX[B] [7] -1 0 0xf5103000 - 0xf5103fff (0x1000) MX[B] [8] -1 0 0xf5102000 - 0xf5102fff (0x1000) MX[B] [9] -1 0 0xf5101000 - 0xf5101fff (0x1000) MX[B] [10] -1 0 0xfebf0000 - 0xfebf00ff (0x100) MX[B] [11] -1 0 0xf5100000 - 0xf5100fff (0x1000) MX[B] [12] -1 0 0xf4000000 - 0xf4ffffff (0x1000000) MX[B](B) [13] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[B](B) [14] -1 0 0xf3000000 - 0xf3ffffff (0x1000000) MX[B](B) [15] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [16] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [17] -1 0 0x000048f0 - 0x000048f7 (0x8) IX[B] [18] -1 0 0x000048c0 - 0x000048cf (0x10) IX[B] [19] -1 0 0x00004c04 - 0x00004c07 (0x4) IX[B] [20] -1 0 0x000048e8 - 0x000048ef (0x8) IX[B] [21] -1 0 0x00004c00 - 0x00004c03 (0x4) IX[B] [22] -1 0 0x000048e0 - 0x000048e7 (0x8) IX[B] [23] -1 0 0x000048b0 - 0x000048bf (0x10) IX[B] [24] -1 0 0x000048fc - 0x000048ff (0x4) IX[B] [25] -1 0 0x000048d8 - 0x000048df (0x8) IX[B] [26] -1 0 0x000048f8 - 0x000048fb (0x4) IX[B] [27] -1 0 0x000048d0 - 0x000048d7 (0x8) IX[B] [28] -1 0 0x000048a0 - 0x000048af (0x10) IX[B] [29] -1 0 0x00004400 - 0x000044ff (0x100) IX[B] [30] -1 0 0x00004000 - 0x000040ff (0x100) IX[B] [31] -1 0 0x00004840 - 0x0000487f (0x40) IX[B] [32] -1 0 0x00004800 - 0x0000483f (0x40) IX[B] [33] -1 0 0x00004880 - 0x0000489f (0x20) IX[B] [34] -1 0 0x0000fb00 - 0x0000fbff (0x100) IX[B] [35] -1 0 0x00003000 - 0x0000307f (0x80) IX[B](B) (II) LoadModule: "extmod" (II) Loading /usr/lib64/xorg/modules/extensions/libextmod.so (II) Module extmod: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.0.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 0.3 (II) Loading extension SHAPE (II) Loading extension MIT-SUNDRY-NONSTANDARD (II) Loading extension BIG-REQUESTS (II) Loading extension SYNC (II) Loading extension MIT-SCREEN-SAVER (II) Loading extension XC-MISC (II) Loading extension XFree86-VidModeExtension (II) Loading extension XFree86-Misc (II) Loading extension XFree86-DGA (II) Loading extension DPMS (II) Loading extension TOG-CUP (II) Loading extension Extended-Visual-Information (II) Loading extension XVideo (II) Loading extension XVideo-MotionCompensation (II) Loading extension X-Resource (II) LoadModule: "dbe" (II) Loading /usr/lib64/xorg/modules/extensions/libdbe.so (II) Module dbe: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.0.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 0.3 (II) Loading extension DOUBLE-BUFFER (II) LoadModule: "glx" (II) Loading /usr/lib64/xorg/modules/extensions/libglx.so (II) Module glx: vendor="NVIDIA Corporation" compiled for 4.0.2, module version = 1.0.0 Module class: X.Org Server Extension (II) NVIDIA GLX Module 185.18.36 Fri Aug 14 18:27:24 PDT 2009 (II) Loading extension GLX (II) LoadModule: "freetype" (II) Loading /usr/lib64/xorg/modules/fonts/libfreetype.so (II) Module freetype: vendor="X.Org Foundation & the After X-TT Project" compiled for 7.1.1, module version = 2.1.0 Module class: X.Org Font Renderer ABI class: X.Org Font Renderer, version 0.5 (II) Loading font FreeType (II) LoadModule: "type1" (II) Loading /usr/lib64/xorg/modules/fonts/libtype1.so (II) Module type1: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.0.2 Module class: X.Org Font Renderer ABI class: X.Org Font Renderer, version 0.5 (II) Loading font Type1 (II) LoadModule: "record" (II) Loading /usr/lib64/xorg/modules/extensions/librecord.so (II) Module record: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.13.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 0.3 (II) Loading extension RECORD (II) LoadModule: "dri" (II) Loading /usr/lib64/xorg/modules/extensions/libdri.so (II) Module dri: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.0.0 ABI class: X.Org Server Extension, version 0.3 (II) Loading sub module "drm" (II) LoadModule: "drm" (II) Loading /usr/lib64/xorg/modules/linux/libdrm.so (II) Module drm: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.0.0 ABI class: X.Org Server Extension, version 0.3 (II) Loading extension XFree86-DRI (II) LoadModule: "nvidia" (II) Loading /usr/lib64/xorg/modules/drivers/nvidia_drv.so (II) Module nvidia: vendor="NVIDIA Corporation" compiled for 4.0.2, module version = 1.0.0 Module class: X.Org Video Driver (II) LoadModule: "kbd" (II) Loading /usr/lib64/xorg/modules/input/kbd_drv.so (II) Module kbd: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.1.0 Module class: X.Org XInput Driver ABI class: X.Org XInput driver, version 0.6 (II) LoadModule: "mouse" (II) Loading /usr/lib64/xorg/modules/input/mouse_drv.so (II) Module mouse: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.1.1 Module class: X.Org XInput Driver ABI class: X.Org XInput driver, version 0.6 (II) NVIDIA dlloader X Driver 185.18.36 Fri Aug 14 17:51:02 PDT 2009 (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs (II) Primary Device is: PCI 0a:00:0 (--) Chipset NVIDIA GPU found (II) Loading sub module "fb" (II) LoadModule: "fb" (II) Loading /usr/lib64/xorg/modules/libfb.so (II) Module fb: vendor="X.Org Foundation" compiled for 7.1.1, module version = 1.0.0 ABI class: X.Org ANSI C Emulation, version 0.3 (II) Loading sub module "wfb" (II) LoadModule: "wfb" (II) Loading /usr/lib64/xorg/modules/libwfb.so (II) Module wfb: vendor="NVIDIA Corporation" compiled for 7.1.99.2, module version = 1.0.0 (II) Loading sub module "ramdac" (II) LoadModule: "ramdac" (II) Loading /usr/lib64/xorg/modules/libramdac.so (II) Module ramdac: vendor="X.Org Foundation" compiled for 7.1.1, module version = 0.1.0 ABI class: X.Org Video Driver, version 1.0 (II) resource ranges after xf86ClaimFixedResources() call: [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [4] -1 0 0xf5000000 - 0xf5003fff (0x4000) MX[B] [5] -1 0 0xf5004000 - 0xf50047ff (0x800) MX[B] [6] -1 0 0xf5104000 - 0xf5104fff (0x1000) MX[B] [7] -1 0 0xf5103000 - 0xf5103fff (0x1000) MX[B] [8] -1 0 0xf5102000 - 0xf5102fff (0x1000) MX[B] [9] -1 0 0xf5101000 - 0xf5101fff (0x1000) MX[B] [10] -1 0 0xfebf0000 - 0xfebf00ff (0x100) MX[B] [11] -1 0 0xf5100000 - 0xf5100fff (0x1000) MX[B] [12] -1 0 0xf4000000 - 0xf4ffffff (0x1000000) MX[B](B) [13] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[B](B) [14] -1 0 0xf3000000 - 0xf3ffffff (0x1000000) MX[B](B) [15] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [16] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [17] -1 0 0x000048f0 - 0x000048f7 (0x8) IX[B] [18] -1 0 0x000048c0 - 0x000048cf (0x10) IX[B] [19] -1 0 0x00004c04 - 0x00004c07 (0x4) IX[B] [20] -1 0 0x000048e8 - 0x000048ef (0x8) IX[B] [21] -1 0 0x00004c00 - 0x00004c03 (0x4) IX[B] [22] -1 0 0x000048e0 - 0x000048e7 (0x8) IX[B] [23] -1 0 0x000048b0 - 0x000048bf (0x10) IX[B] [24] -1 0 0x000048fc - 0x000048ff (0x4) IX[B] [25] -1 0 0x000048d8 - 0x000048df (0x8) IX[B] [26] -1 0 0x000048f8 - 0x000048fb (0x4) IX[B] [27] -1 0 0x000048d0 - 0x000048d7 (0x8) IX[B] [28] -1 0 0x000048a0 - 0x000048af (0x10) IX[B] [29] -1 0 0x00004400 - 0x000044ff (0x100) IX[B] [30] -1 0 0x00004000 - 0x000040ff (0x100) IX[B] [31] -1 0 0x00004840 - 0x0000487f (0x40) IX[B] [32] -1 0 0x00004800 - 0x0000483f (0x40) IX[B] [33] -1 0 0x00004880 - 0x0000489f (0x20) IX[B] [34] -1 0 0x0000fb00 - 0x0000fbff (0x100) IX[B] [35] -1 0 0x00003000 - 0x0000307f (0x80) IX[B](B) (II) resource ranges after probing: [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [4] -1 0 0xf5000000 - 0xf5003fff (0x4000) MX[B] [5] -1 0 0xf5004000 - 0xf50047ff (0x800) MX[B] [6] -1 0 0xf5104000 - 0xf5104fff (0x1000) MX[B] [7] -1 0 0xf5103000 - 0xf5103fff (0x1000) MX[B] [8] -1 0 0xf5102000 - 0xf5102fff (0x1000) MX[B] [9] -1 0 0xf5101000 - 0xf5101fff (0x1000) MX[B] [10] -1 0 0xfebf0000 - 0xfebf00ff (0x100) MX[B] [11] -1 0 0xf5100000 - 0xf5100fff (0x1000) MX[B] [12] -1 0 0xf4000000 - 0xf4ffffff (0x1000000) MX[B](B) [13] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[B](B) [14] -1 0 0xf3000000 - 0xf3ffffff (0x1000000) MX[B](B) [15] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B] [16] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B] [17] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B] [18] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [19] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [20] -1 0 0x000048f0 - 0x000048f7 (0x8) IX[B] [21] -1 0 0x000048c0 - 0x000048cf (0x10) IX[B] [22] -1 0 0x00004c04 - 0x00004c07 (0x4) IX[B] [23] -1 0 0x000048e8 - 0x000048ef (0x8) IX[B] [24] -1 0 0x00004c00 - 0x00004c03 (0x4) IX[B] [25] -1 0 0x000048e0 - 0x000048e7 (0x8) IX[B] [26] -1 0 0x000048b0 - 0x000048bf (0x10) IX[B] [27] -1 0 0x000048fc - 0x000048ff (0x4) IX[B] [28] -1 0 0x000048d8 - 0x000048df (0x8) IX[B] [29] -1 0 0x000048f8 - 0x000048fb (0x4) IX[B] [30] -1 0 0x000048d0 - 0x000048d7 (0x8) IX[B] [31] -1 0 0x000048a0 - 0x000048af (0x10) IX[B] [32] -1 0 0x00004400 - 0x000044ff (0x100) IX[B] [33] -1 0 0x00004000 - 0x000040ff (0x100) IX[B] [34] -1 0 0x00004840 - 0x0000487f (0x40) IX[B] [35] -1 0 0x00004800 - 0x0000483f (0x40) IX[B] [36] -1 0 0x00004880 - 0x0000489f (0x20) IX[B] [37] -1 0 0x0000fb00 - 0x0000fbff (0x100) IX[B] [38] -1 0 0x00003000 - 0x0000307f (0x80) IX[B](B) [39] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B] [40] 0 0 0x000003c0 - 0x000003df (0x20) IS[B] (II) Setting vga for screen 0. (**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32 (==) NVIDIA(0): RGB weight 888 (==) NVIDIA(0): Default visual is TrueColor (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0) (**) NVIDIA(0): Option "TwinView" "0" (**) NVIDIA(0): Option "MetaModes" "nvidia-auto-select +0+0" (**) NVIDIA(0): Enabling RENDER acceleration (II) NVIDIA(0): Support for GLX with the Damage and Composite X extensions is (II) NVIDIA(0): enabled. (II) NVIDIA(0): NVIDIA GPU Quadro FX 4500 (G70GL) at PCI:10:0:0 (GPU-0) (--) NVIDIA(0): Memory: 524288 kBytes (--) NVIDIA(0): VideoBIOS: 05.70.02.41.01 (II) NVIDIA(0): Detected PCI Express Link width: 16X (--) NVIDIA(0): Interlaced video modes are supported on this GPU (--) NVIDIA(0): Connected display device(s) on Quadro FX 4500 at PCI:10:0:0: (--) NVIDIA(0): DELL 3007WFP (DFP-0) (--) NVIDIA(0): DELL 3007WFP (DFP-0): 310.0 MHz maximum pixel clock (--) NVIDIA(0): DELL 3007WFP (DFP-0): Internal Dual Link TMDS (II) NVIDIA(0): Assigned Display Device: DFP-0 (II) NVIDIA(0): Validated modes: (II) NVIDIA(0): "nvidia-auto-select+0+0" (II) NVIDIA(0): Virtual screen size determined to be 2560 x 1600 (--) NVIDIA(0): DPI set to (101, 101); computed from "UseEdidDpi" X config (--) NVIDIA(0): option (WW) NVIDIA(0): UBB is incompatible with the Composite extension. Disabling (WW) NVIDIA(0): UBB. (==) NVIDIA(0): Disabling 32-bit ARGB GLX visuals. (--) Depth 24 pixmap format is 32 bpp (II) do I need RAC? No, I don't. (II) resource ranges after preInit: [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [4] -1 0 0xf5000000 - 0xf5003fff (0x4000) MX[B] [5] -1 0 0xf5004000 - 0xf50047ff (0x800) MX[B] [6] -1 0 0xf5104000 - 0xf5104fff (0x1000) MX[B] [7] -1 0 0xf5103000 - 0xf5103fff (0x1000) MX[B] [8] -1 0 0xf5102000 - 0xf5102fff (0x1000) MX[B] [9] -1 0 0xf5101000 - 0xf5101fff (0x1000) MX[B] [10] -1 0 0xfebf0000 - 0xfebf00ff (0x100) MX[B] [11] -1 0 0xf5100000 - 0xf5100fff (0x1000) MX[B] [12] -1 0 0xf4000000 - 0xf4ffffff (0x1000000) MX[B](B) [13] -1 0 0xc0000000 - 0xcfffffff (0x10000000) MX[B](B) [14] -1 0 0xf3000000 - 0xf3ffffff (0x1000000) MX[B](B) [15] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B] [16] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B] [17] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B] [18] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [19] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [20] -1 0 0x000048f0 - 0x000048f7 (0x8) IX[B] [21] -1 0 0x000048c0 - 0x000048cf (0x10) IX[B] [22] -1 0 0x00004c04 - 0x00004c07 (0x4) IX[B] [23] -1 0 0x000048e8 - 0x000048ef (0x8) IX[B] [24] -1 0 0x00004c00 - 0x00004c03 (0x4) IX[B] [25] -1 0 0x000048e0 - 0x000048e7 (0x8) IX[B] [26] -1 0 0x000048b0 - 0x000048bf (0x10) IX[B] [27] -1 0 0x000048fc - 0x000048ff (0x4) IX[B] [28] -1 0 0x000048d8 - 0x000048df (0x8) IX[B] [29] -1 0 0x000048f8 - 0x000048fb (0x4) IX[B] [30] -1 0 0x000048d0 - 0x000048d7 (0x8) IX[B] [31] -1 0 0x000048a0 - 0x000048af (0x10) IX[B] [32] -1 0 0x00004400 - 0x000044ff (0x100) IX[B] [33] -1 0 0x00004000 - 0x000040ff (0x100) IX[B] [34] -1 0 0x00004840 - 0x0000487f (0x40) IX[B] [35] -1 0 0x00004800 - 0x0000483f (0x40) IX[B] [36] -1 0 0x00004880 - 0x0000489f (0x20) IX[B] [37] -1 0 0x0000fb00 - 0x0000fbff (0x100) IX[B] [38] -1 0 0x00003000 - 0x0000307f (0x80) IX[B](B) [39] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B] [40] 0 0 0x000003c0 - 0x000003df (0x20) IS[B] (II) NVIDIA(GPU-1): NVIDIA GPU Quadro FX 4500 (G70GL) at PCI:129:0:0 (GPU-1) (--) NVIDIA(GPU-1): Memory: 524288 kBytes (--) NVIDIA(GPU-1): VideoBIOS: 05.70.02.41.01 (II) NVIDIA(GPU-1): Detected PCI Express Link width: 16X (--) NVIDIA(GPU-1): Interlaced video modes are supported on this GPU (--) NVIDIA(GPU-1): Connected display device(s) on Quadro FX 4500 at PCI:129:0:0: (--) NVIDIA(GPU-1): DELL 3007WFP (DFP-0) (--) NVIDIA(GPU-1): DELL 3007WFP (DFP-0): 310.0 MHz maximum pixel clock (--) NVIDIA(GPU-1): DELL 3007WFP (DFP-0): Internal Dual Link TMDS (II) NVIDIA(0): Initialized GPU GART. (II) NVIDIA(0): Setting mode "nvidia-auto-select+0+0" (II) Loading extension NV-GLX (II) NVIDIA(0): NVIDIA 3D Acceleration Architecture Initialized (==) NVIDIA(0): Disabling shared memory pixmaps (II) NVIDIA(0): Using the NVIDIA 2D acceleration architecture (==) NVIDIA(0): Backing store disabled (==) NVIDIA(0): Silken mouse enabled (**) Option "dpms" (**) NVIDIA(0): DPMS enabled (II) Loading extension NV-CONTROL (==) RandR enabled (II) Setting vga for screen 0. (II) Initializing built-in extension MIT-SHM (II) Initializing built-in extension XInputExtension (II) Initializing built-in extension XTEST (II) Initializing built-in extension XKEYBOARD (II) Initializing built-in extension XC-APPGROUP (II) Initializing built-in extension SECURITY (II) Initializing built-in extension XINERAMA (II) Initializing built-in extension XFIXES (II) Initializing built-in extension XFree86-Bigfont (II) Initializing built-in extension RENDER (II) Initializing built-in extension RANDR (II) Initializing built-in extension COMPOSITE (II) Initializing built-in extension DAMAGE (II) Initializing built-in extension XEVIE (II) Initializing extension GLX (WW) Disabling Composite since Xinerama is enabled (**) Option "CoreKeyboard" (**) Keyboard0: Core Keyboard (**) Option "Protocol" "standard" (**) Keyboard0: Protocol: standard (**) Option "AutoRepeat" "500 30" (**) Option "XkbRules" "xorg" (**) Keyboard0: XkbRules: "xorg" (**) Option "XkbModel" "pc105" (**) Keyboard0: XkbModel: "pc105" (**) Option "XkbLayout" "us" (**) Keyboard0: XkbLayout: "us" (**) Option "CustomKeycodes" "off" (**) Keyboard0: CustomKeycodes disabled (**) Option "Protocol" "auto" (**) Mouse0: Device: "/dev/input/mice" (**) Mouse0: Protocol: "auto" (**) Option "CorePointer" (**) Mouse0: Core Pointer (**) Option "Device" "/dev/input/mice" (**) Option "Emulate3Buttons" "no" (**) Option "ZAxisMapping" "4 5" (**) Mouse0: ZAxisMapping: buttons 4 and 5 (**) Mouse0: Buttons: 9 (II) XINPUT: Adding extended input device "Mouse0" (type: MOUSE) (II) XINPUT: Adding extended input device "Keyboard0" (type: KEYBOARD) (--) Mouse0: PnP-detected protocol: "ExplorerPS/2" (II) Mouse0: ps2EnableDataReporting: succeeded (II) Open ACPI successful (/var/run/acpid.socket) (II) NVIDIA(0): Setting mode "nvidia-auto-select+0+0" (II) Mouse0: ps2EnableDataReporting: succeeded (the snipped part can be changed if necessary) Any help at all would be appreciated. Cheers, Alex

  Read the article

• How to troubleshoot performance issues of PHP, MySQL and generic I/O

  - by jbx

  I have a WordPress based website running on a shared hosting. Its response time is very decent (around 2s to retrieve the HTML page and 5s to load all the resources). I was planning to move it to a dedicated virtual server (Ubuntu 12.04 LTS), which should theoretically improve things and make them more consistent given its not shared. However I observed severe performance degredation, with the page taking 10seconds to be generated. I ruled out network issues by editing /etc/hosts on the server and mapping the domain to 127.0.0.1. I used the Apache load tester ab to get the HTML, so JS, CSS and images are all excluded. It still took 10 seconds. I have Zpanel installed on the server which also uses MySQL, and its pages come up quite fast (1.5s) and also phpMyAdmin. Performing some queries on the wordpress database directly through phpMyAdmin returns them quite fast too, with query times in the 10 to 30 millisecond region. Memory is also sufficient, with only 800Mb being used of the 1Gb physical memory available, so it doesn't seem to be a swap issue either. I have also installed APC to try to improve the PHP performance, but it didn't have any effect. What else should I look for? What could be causing this degradation in performance? Could it be some kind of I/O issue since I am running on a cloud based virtual server? I wish to be able to raise the issue with my provider but without showing actual data from some diagnosis I am afraid he will just blame my application. UPDATE with sar output (every second) when I did an HTTP request: 02:31:29 CPU %user %nice %system %iowait %steal %idle 02:31:30 all 0.00 0.00 0.00 0.00 0.00 100.00 02:31:31 all 2.22 0.00 2.22 0.00 0.00 95.56 02:31:32 all 41.67 0.00 6.25 0.00 2.08 50.00 02:31:33 all 86.36 0.00 13.64 0.00 0.00 0.00 02:31:34 all 75.00 0.00 25.00 0.00 0.00 0.00 02:31:35 all 93.18 0.00 6.82 0.00 0.00 0.00 02:31:36 all 90.70 0.00 9.30 0.00 0.00 0.00 02:31:37 all 71.05 0.00 0.00 0.00 0.00 28.95 02:31:38 all 14.89 0.00 10.64 0.00 2.13 72.34 02:31:39 all 2.56 0.00 0.00 0.00 0.00 97.44 02:31:40 all 0.00 0.00 0.00 0.00 0.00 100.00 02:31:41 all 0.00 0.00 0.00 0.00 0.00 100.00 My suspicion that this comes from I/O related issue is also because a caching plugin I use to reduce the amount of queries to the database, by precompiling PHP pages is actually making things worse instead of better. It seems that file access is making things worse instead.

  Read the article

• Apache/Jboss Issue - is this connection timeout?

  - by user115391

  We have an application. The architecture is as below 1 load balancer (apache), which redirects to 2 app servers (jboss). The site is working fine and I am able to access it fine. But sometimes, randomly the homepage takes a while (like 30-40 secs) to load. I tried checking the logs but could not figure out why. I used the httptraffic analyzer, fiddler to see the traffic, but it just says the request/response took 30 secs or so. I checked the apache access logs, mod_jk.log. My configurations are below mod-jk.conf LoadModule jk_module modules/mod_jk.so JkWorkersFile conf/workers.properties JkLogFile logs/mod_jk.log #JkLogLevel info #JkLogLevel debug JkLogLevel error # Select the log format JkLogStampFormat "[%a %b %d %H:%M:%S %Y]" JkOptions +ForwardKeySize +ForwardURICompatUnparsed -ForwardDirectories JkRequestLogFormat "%w %V %T %P %{tid}P %D" JkMount /__application__/* loadbalancer JkUnMount /__application__/images/* loadbalancer <VirtualHost *:8080 > JkMountFile conf/uriworkermap.properties </VirtualHost> JkShmFile run/jk.shm <Location /jkstatus> JkMount status Order deny,allow Deny from all Allow from 127.0.0.1 </Location> ----------------------------- uriworkermap.properties Simple worker configuration file # Mount the Servlet context to the ajp13 worker /=loadbalancer /*=loadbalancer ----------------------------- workers.properties worker.list=loadbalancer,status worker.template.port=8009 worker.template.type=ajp13 worker.template.lbfactor=1 worker.template.prepost_timeout=10000 worker.template.connect_timeout=10000 worker.template.ping_mode=A worker.worker1.reference=worker.template worker.worker1.host=hostname1 worker.worker2.reference=worker.template worker.worker2.host=hostname2 worker.loadbalancer.type=lb worker.loadbalancer.balance_workers=worker1,worker2 worker.status.type=status ----------------------------- my jboss server.xml - $JBOSS_HOME/server/default/deploy/jbossweb.sar/server.xml --------------------------------- The logs from access log is below The issue where it took time - look at the seconds column [23/Mar/2012:12:10:38 -0400] "GET / HTTP/1.1" 200 138 x.x.x.x - - [23/Mar/2012:12:10:49 -0400] "GET /index.jsp HTTP/1.1" 302 - x.x.x.x - - [23/Mar/2012:12:11:10 -0400] "GET /home.jsp HTTP/1.1" 200 936 x.x.x.x - - [23/Mar/2012:12:11:31 -0400] "POST /login/ HTTP/1.1" 200 8895 x.x.x.x - - [23/Mar/2012:12:11:52 -0400] "GET /login/includes/login-style.css HTTP/1.1" 304 - The one after the issue x.x.x.x - - [23/Mar/2012:12:12:18 -0400] "GET / HTTP/1.1" 200 138 x.x.x.x - - [23/Mar/2012:12:12:18 -0400] "GET /index.jsp HTTP/1.1" 302 - x.x.x.x - - [23/Mar/2012:12:12:18 -0400] "GET /home.jsp HTTP/1.1" 200 936 x.x.x.x - - [23/Mar/2012:12:12:18 -0400] "POST /login/ HTTP/1.1" 200 8895 x.x.x.x - - [23/Mar/2012:12:12:18 -0400] "GET /login/includes/login-style.css HTTP/1.1" 304 - Would it be a cache or timeout issue? Any help is appreciated. Thanks.

  Read the article

• What "pieces" are needed in order to set up a cluster of physical servers?

  - by Chris Dutrow

  Background: Currently, we use Rackspace cloud servers. We have no intention to stop using them, but would like to look into setting up a cluster of physical servers (probably desktop computers in the $400 range with 8gb memory each) to offset some of our load and work as a secondary, more powerful, less reliable system. To put things in perspective, we can buy comparable desktop computers for the same price as we pay in one month to rent them on Rackspace Cloud. I understand that this is generally a dumb idea. However, in this particular instance, the server cluster is needed for its computation power. It is not mission-critical, it does not host a consumer-facing website, and if it goes down for a day or two, its not really a problem. Currently, we have access to business class verizon fios. If I understand correctly, we can get at least 25 dedicated IP addresses with this service, this should be enough. Requirements: Each server runs Linux Centos 6.3 Some of the servers run Python and execute processes from a task queue (Redis or RabbitMQ) Some of the servers are capable of serving static files and Python driven REST APIs Some of the servers host a Cassandra database cluster One or more of the servers are a Redis database servers One or more of the servers are PostgreSQL servers Questions: What kind of router or switch is needed? We would like the computers to be able to communicate effectively with each other via internal IP addresses. This is especially important for communicating with servers hosting Redis that need to be able to respond to requests very quickly. Are there special switches or routers that need to be used to connect the servers together? Are Desktop computers ok for this? We have found that we are mostly RAM-bottle necked, I understand that some servers have highly superior CPUs, but I'm not sure we need CPU power as much as we need RAM, which is cheap in Desktop computers. Will we have problems with the WIFI cards in the desktops or any other unexpected hardware limitation? What tools should be used to "image" the servers. For example, when we get an installation right for a Redis server or Cassandra node, are there tools that come with Linux Centos 6.3 to image the server to a USB drive or something like that? Or do we need to use some other software for this? What other things are we missing that we should be concerned about? Thanks so much!

  Read the article

• Python Django sites on Apache+mod_wsgi with nginx proxy: highly fluctuating performance

  - by Halfgaar

  I have an Ubuntu 10.04 box running several dozen Python Django sites using mod_wsgi (embedded mode; the faster mode, if properly configured). Performance highly fluctuates. Sometimes fast, sometimes several seconds delay. The smokeping graphs are al over the place. Recently, I also added an nginx proxy for the static content, in the hopes it would cure the highly fluctuating performance. But, even though it reduced the number of requests Apache has to process significantly, it didn't help with the main problem. When clicking around on websites while running htop, it can be seen that sometimes requests are almost instant, whereas sometimes it causes Apache to consume 100% CPU for a few seconds. I really don't understand where this fluctuation comes from. I have configured the mpm_worker for Apache like this: StartServers 1 MinSpareThreads 50 MaxSpareThreads 50 ThreadLimit 64 ThreadsPerChild 50 MaxClients 50 ServerLimit 1 MaxRequestsPerChild 0 MaxMemFree 2048 1 server with 50 threads, max 50 clients. Munin and apache2ctl -t both show a consistent presence of workers; they are not destroyed and created all the time. Yet, it behaves as such. This tells me that once a sub interpreter is created, it should remain in memory, yet it seems sites have to reload all the time. I also have a nginx+gunicorn box, which performs quite well. I would really like to know why Apache is so random. This is a virtual host config: <VirtualHost *:81> ServerAdmin [email protected] ServerName example.com DocumentRoot /srv/http/site/bla Alias /static/ /srv/http/site/static Alias /media/ /srv/http/site/media WSGIScriptAlias / /srv/http/site/passenger_wsgi.py <Directory /> AllowOverride None </Directory> <Directory /srv/http/site> Options -Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> Ubuntu 10.04 Apache 2.2.14 mod_wsgi 2.8 nginx 0.7.65 Edit: I've put some code in the settings.py file of a site that writes the date to a tmp file whenever it's loaded. I can now see that the site is not randomly reloaded all the time, so Apache must be keeping it in memory. So, that's good, except it doesn't bring me closer to an answer... Edit: I just found an error that might also be related to this: File "/usr/lib/python2.6/subprocess.py", line 633, in __init__ errread, errwrite) File "/usr/lib/python2.6/subprocess.py", line 1049, in _execute_child self.pid = os.fork() OSError: [Errno 12] Cannot allocate memory The server has 600 of 2000 MB free, which should be plenty. Is there a limit that is set on Apache or WSGI somewhere?

  Read the article

• Server freezes at XX:25

  - by Karevan

  We've ordered a 50 euro/month server on hetzner.de, it has debian OS. The problem is that server is freezing in random time of the day and nothing appears in log. Only hardware reboot helps. Part of the log file while it was freezing: Aug 17 22:38:26 Debian-60-squeeze-64-minimal pure-ftpd: ([email protected]) [INFO] New connection from 95.211.120.220 Aug 17 22:38:26 Debian-60-squeeze-64-minimal pure-ftpd: ([email protected]) [INFO] Logout. Aug 17 22:39:01 Debian-60-squeeze-64-minimal /USR/SBIN/CRON[22828]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -type$ Aug 17 23:09:01 Debian-60-squeeze-64-minimal /USR/SBIN/CRON[22835]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -type$ Aug 17 23:17:01 Debian-60-squeeze-64-minimal /USR/SBIN/CRON[22842]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Aug 17 23:39:01 Debian-60-squeeze-64-minimal /USR/SBIN/CRON[22847]: (root) CMD ( [ -x /usr/lib/php5/maxlifetime ] && [ -d /var/lib/php5 ] && find /var/lib/php5/ -type$ Aug 18 09:47:47 Debian-60-squeeze-64-minimal kernel: imklog 4.6.4, log source = /proc/kmsg started. Aug 18 09:47:47 Debian-60-squeeze-64-minimal rsyslogd: [origin software="rsyslogd" swVersion="4.6.4" x-pid="1229" x-info="http://www.rsyslog.com"] (re)start Aug 18 09:47:47 Debian-60-squeeze-64-minimal kernel: [ 0.000000] Initializing cgroup subsys cpuset Aug 18 09:47:47 Debian-60-squeeze-64-minimal kernel: [ 0.000000] Initializing cgroup subsys cpu Aug 18 09:47:47 Debian-60-squeeze-64-minimal kernel: [ 0.000000] Linux version 2.6.32-5-amd64 (Debian 2.6.32-45) ([email protected]) (gcc version 4.3.5 (Debian 4.3.5$ Aug 18 09:47:47 Debian-60-squeeze-64-minimal kernel: [ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-2.6.32-5-amd64 root=/dev/md2 ro As you can see, it appears only the fact of starting. No. theres no way to look in server's console right after when it freezes, sadly. Datacenter supporters do not really want to help about that. Server has been installed 30th july, times and dates of freezes are down there: 6 august, 0:25 18 august, 2:27 21 august, 1:25 26 august, 23:26. We decided that freezing around ??:25 isn't a hardware fault, and decided to reinstall the OS. Later, 31 august, our admin backed up all files, reinstalled Debian, and restored the backup. But then, 7 september, server went down again, at 5:05. We thought it was related to Anyone else experiencing high rates of Linux server crashes during a leap second day? and turned ntp off. But then the server went down twice again, 21 september, 17:29 and 24 september, 20:27. I called all linux admins I knew to help with solving it and they said everything is fine about configuring OS and it could be hardware only. But they dont know why it always freezes at XX:25-30. Maybe some of you know about something related to that?

  Read the article

• My server is slower than the average user's computer, should I still offload Access queries to SQL Server? [closed]

  - by andrewb

  Possible Duplicate: How do you do Load Testing and Capacity Planning for Databases I have a database set up with MS Access 2007 front ends and an SQL Server 2005 back end. At the moment, all the queries are saved in the front end as I've only recently moved to an SQL Server backend. I'm wondering how much of those queries I should save as stored procedures/views on SQL Server. About the system The number of concurrent users is only a handful, though it could be as high as 25 at one time (very unlikely). The average computer has an Intel i3-2120 CPU running at 3.3 GHz, which gets a PassMark score of 3,987, whilst the server has an Intel Xeon E5335 running at 2.0 GHz, which gets a PassMark score of 2,637. Always an awkward situation when an i3 outperforms a Xeon... though the i3 is from Q1 2011 and the Xeon is Q2 2009. There is potential for a server upgrade in the future, though it wouldn't come easy. I'm inclined to move the queries to the back end, as they are beginning to take noticeable time and I figure that is a better way of doing things. I like the idea of throwing everything at the server, then pushing for a server upgrade. It makes more sense in my mind to be upgrading one server rather than 30 PCs. Or am I being overzealous? Why my question isn't a duplicate It seems that my question has been misinterpreted and labelled a duplicate of quite a different question, one about testing and capacity planning. I'll try explain how my question is very different from the linked question. The crux of my question is something like "Even though my server is technically slower, is it better to have it doing more of the queries?" There's two ways that people could have answered this: I agree the server is going to be slower, but the extra benefits of such and such (like the less Access the better) means you should move most to the server anyway. (OR no it doesn't outweigh the benefit, keep them in Access) Actually the server will be faster because of such and such. I'm hoping that people out there could provide some answers like this, and the question in the dupe link doesn't really provide either of these answers. Ok sure, I suppose I could do extensive performance testing to compare Access queries running on a local machine to SQL Server queries running on the server, but that sounds like a very hard task (particularly performance testing of access) compared to someone giving some quick general guidance, and again, my question is looking for a lot more than immediate performance benefit.

  Read the article

• How to stop a random ramp in FCGI Processes Killing the server

  - by Andy Main

  So got the below earlier to day... Around that time the logs show a ramp in processes(600) and associated memory (1.2g), cpu usage load average (80) untill the server gave out. Server had to be hard reset by host as there was no ssh or plesk panel access. Fast CGI is configured as below and is setup for one high use site. As I understand it FcgidMaxProcesses 20 should protect against what happen but has not. I've read many forums with differing answers and references to many different fcgi directives, but have found nothing conclusive. Any one got some definitive answers on how to stop this sort of server process ramping and subsequent server failure? If you need more info let me know. Cheers Andy  /var/log/apache2/error_log [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17651 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17650 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17649 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17644 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17643 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17638 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17633 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17627 graceful kill fail, sending SIGKILL [Thu May 17 07:40:47 2012] [warn] mod_fcgid: process 17622 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17674 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17673 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17672 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17667 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17666 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17665 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17664 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17659 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17658 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17657 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17656 graceful kill fail, sending SIGKILL [Thu May 17 07:40:51 2012] [warn] mod_fcgid: process 17651 graceful kill fail, sending SIGKILL https://docs.google.com/a/thesugarrefinery.com/open?id=0B_XbpWChge0VRmFLWEZfR2VBb2M https://docs.google.com/a/thesugarrefinery.com/open?id=0B_XbpWChge0VWTcwZEhoV2Fqejg https://docs.google.com/a/thesugarrefinery.com/open?id=0B_XbpWChge0VUUtVWWFINHZjZ0U https://docs.google.com/a/thesugarrefinery.com/open?id=0B_XbpWChge0VZEVMclh6ZUdaOUE <IfModule mod_fcgid.c> <IfModule !mod_fastcgi.c> AddHandler fcgid-script fcg fcgi fpl </IfModule> FcgidIPCDir /var/lib/apache2/fcgid/sock FcgidProcessTableFile /var/lib/apache2/fcgid/shm FcgidIdleTimeout 40 FcgidProcessLifeTime 30 FcgidMaxProcesses 20 FcgidMaxProcessesPerClass 20 FcgidMinProcessesPerClass 0 FcgidConnectTimeout 30 FcgidIOTimeout 120 FcgidInitialEnv RAILS_ENV production FcgidIdleScanInterval 10 FcgidMaxRequestLen 1073741824 </IfModule>

  Read the article

< Previous Page | 373 374 375 376 377 378 379 380 381 382 383 384  | Next Page >