Search Results

Search found 9975 results on 399 pages for 'enterprise architecture'.

Page 377/399 | < Previous Page | 373 374 375 376 377 378 379 380 381 382 383 384  | Next Page >

  • PC: Quick Freeze, then BSOD, then forced reboot, then freezes again

    - by cr0z3r
    Lately I have been experiencing a weird issue. My PC will hang for a second and then BSOD - it stays there, so I have to reboot. Once Windows starts again and I'm logged in, after 1-10min it freezes again, this time without BSOD. RECAP: 1 second freeze BSOD, hangs there I have to force-reboot Once PC rebooted, I log back into Windows second freeze between a 1-10min range, no BSOD (alternatively, I get a freeze with a constant sound/noise, no BSOD) I contacted my PC provider, who told me my graphics-card might be flawed (Quadro 4000), so I used a Quadro 2000 that they lend me. The issue still occurred. The issue now seemed to belong to a flawed RAM module. Following my provider's steps, I removed all but the first from the left column and kept using my PC for a week or so without any issues. I then added the bottom-right module, and so on, until all modules were back inside - I had no problems. Now it seemed that a simple take-out-put-back-in of the RAM modules had fixed the issue. However, after a few months, the issue was back. I redid all the RAM-swapping I had done before, and concluded that the lower-right module was flawed. My provider changed it for another, and everything was great until now. My PC froze again for barely a second, hanged on a BSOD, I rebooted it, logged-in to Windows to get a freeze (without BSOD or reboot) 40 seconds later. Something worth noting, is that every time I reboot after the BSOD, it is something within Chrome that freezes my PC (e.g. this time I clicked the "restore" button as Chrome mentioned it had exited unexpectedly - from the previous freeze obviously - and it instantly froze). Finally, the Event Viewer lists 2 critical events in the past hour as "ID: 41, Type: Kernel-Power". PC-Specs: http://i.imgur.com/VZpbr.jpg Previous Dump-files: https://dl.dropbox.com/u/716600/DumpFiles_08_2012.zip I would like to thank anybody in advance for your help. You're great. UPDATE 1: I realized that I did not mention an awkward fact about this issue. After I have gotten the 1-sec freeze followed by a BSOD, after I rebooted because the BSOD hanged, and after I logged back in to get another (this time, eternal) freeze and rebooted once again, the PC does not boot back up. The power-light is on, but my monitor says "no signal", as if the PC wouldn't really be turned on. This truly seems a like a power-related issue, doesn't it? UPDATE 2: I just got a freeze, but without BSOD. My screen froze (while on Chrome, which is starting to seem suspicious to me) with an ongoing sound/noise. I had to force-reboot my PC. I would say this is a graphics-card issue, but this issue also happened when I was using the Quadro 2000 from my provider. UPDATE 3: I just got a BSOD while trying to render something (quite heavy, actually) in 3ds Max 2012. I left the BSOD "running", as it said it was writing dump files to disk. However, the percentage number stayed at 0, so after 15 minutes I force-rebooted. I then used the software WhoCrashed (thank you Dave) which reported the following from the C:\Windows\Memory.dmp file: On Thu 22.11.2012 22:13:45 GMT your computer crashed crash dump file: C:\Windows\memory.dmp uptime: 01:05:27 This was probably caused by the following module: Unknown () Bugcheck code: 0x124 (0x0, 0xFFFFFA80275AC028, 0xF200001F, 0x100B2) Error: WHEA_UNCORRECTABLE_ERROR Bug check description: This bug check indicates that a fatal hardware error has occurred. This bug check uses the error data that is provided by the Windows Hardware Error Architecture (WHEA). This is likely to be caused by a hardware problem problem. This problem might be caused by a thermal issue. A third party driver was identified as the probable root cause of this system error. It is suggested you look for an update for the following driver: Unknown . Google query: Unknown WHEA_UNCORRECTABLE_ERROR

    Read the article

  • Exchange Server 2007 Setup

    - by AlamedaDad
    Hi, I'm working on a upgrade to Exchange 2007 and I wanted to get some advise on hardware choices. We currently have an Exchange 2003 STD server with 400 users split between 6 AD Sites, that is housed on a single server. We need to move to a redundant, fault tolerant system to support our users. I'm planning on installing 2 Dell 1950 servers with W2k8-std to act as CAS and Hub servers, with NLB to allow abstraction of the actual server name to the users. There won't be an edge system since we have a Barracuda box already that will handle in/out spam/virus filtering. Backend I'm planning on 2 mailbox servers which will be Dell 2950s with 16GB RAM, 2 either dual-core or quad-core CPUs and 6 300GB SAS drives in some RAID config. These systems will be clustered using W2k8 Ent clustering and running CCR in Exchange. My questions are as follows: Is 16GB enough RAM for serving that many mailboxes along with the windows clustering and ccr? I'm trying to figure out disk layouts and I'm unsure of whether to use all local disk or some local and some SAN, via an OpenFiler iSCSI server. The SAN would be a Dell 2850 with 6 - 300GB SCSI drives and a PERC controller to slice as I want, with 8GB RAM. Option 1: 2 drives, RAID 1 - OS 2 drives, RAID 1 - Logs 2 drives, RAID 1 - Mail stores Option 2: 2 drives, RAID 1 - OS and logs 4 drives, RAID 5 - Mail Stores and scratch space for eseutil. Option 3: 2 drives, RAID 1 - OS 2 drives, RAID 1 - Logs 2 drives, RAID 0 - scratch space ~300GB iSCSI volume for mail stores Option 4: 2 drives, RAID 1 - OS 4 drives, RAID 5 - scratch space ~300GB iSCSI volume for mail stores ~300GB iSCSI volume for logs I have 2 sockets for CPUs and need to chose between dual and quad cores. The dual core have faster clocks but less cache and I'm thinking older architecture. Am I better off with more cores and cache while sacraficing clock speed? I am planning on adding the new E2K7 cluster to the E2K3 server and then move each mailbox over, all at once, then remove the old server. This seems more complicated than simply getting rid of the 2003 server and then adding the 2007 cluster and restoring the mailboxes using PowerControls or exmerge. The migration option lets me do this on my time, where a cutover means it all needs to work at once. If I go with the cutover method, how can I prebuild the servers and add them to the domain right after removing the 2003 server, or can't I? I think the answer is no and the migration is my only real option if I want to prebuild. I need to also migrate about 30GB of Public Folders. Is there anything special about this, other than specifying in the E2K7 install that I want older Outlook clients and PF's setup? I guess I could even keep the E2K3 server to host just the PFs? Lastly, if I have a mix of Outlook 200, 2003 and 2007 what do I need to do to make sure they all have access to the GAL and OAB? At time of cutover, we'll be at like 90% 2007, but we will have some older stuff around. My plan is to use Outlook Anywhere on laptops that are used outside the physical network. Are there any gotchas involved in that? I'm even thinking about using is for all Outlook clients, does anyone do that? The reason I'm considering it is that our WAN is really VPN tunnels over internet connections, so not a fully messhed, stable WAN. Thank you all very much for the assistance in advance and I look forward to discussion of these points! Regards...Michael

    Read the article

  • windows 2003 server : can't join domain

    - by phill
    I originally tried to rejoin a computer to a network which led to a "cannot find domain" error. The username/password box don't even come up. some tests i ran: I can ping the server, however I can't ping the domain name domain1.local. nslookup can't find the domain either. It looks to the isp's dns instead of my own to resolve the local machines. So i go to the dns and run netdiag.exe and gives me this error. DNS test . . . . . . . . . . . . . : Failed [WARNING] Cannot find a primary authoritative DNS server for the name 'stmartinsrv.stmartin.local.'. [RCODE_SERVER_FAILURE] The name 'srv.domain1.local.' may not be registered in DNS. [WARNING] The DNS entries for this DC are not registered correctly on DNS se rver '68.94.156.1'. Please wait for 30 minutes for DNS server replication. [WARNING] The DNS entries for this DC are not registered correctly on DNS se rver '68.94.157.1'. Please wait for 30 minutes for DNS server replication. [FATAL] No DNS servers have the DNS records for this DC registered. Redir and Browser test . . . . . . : Passed List of NetBt transports currently bound to the Redir NetBT_Tcpip_{04BB0F6B-06AE-4D60-80C8-2A7A24C1D87B} The redir is bound to 1 NetBt transport. List of NetBt transports currently bound to the browser NetBT_Tcpip_{04BB0F6B-06AE-4D60-80C8-2A7A24C1D87B} The browser is bound to 1 NetBt transport. then running dcdiag C:\Program Files\Support Toolsdcdiag Domain Controller Diagnosis Performing initial setup: Done gathering initial info. Doing initial required tests Testing server: Default-First-Site-Name\SRV Starting test: Connectivity The host 1c99f63c-49ec-40db-b3d3-6265c00fbd3e._msdcs.domain1.local cou ld not be resolved to an IP address. Check the DNS server, DHCP, server name, etc Although the Guid DNS name (1c99f63c-49ec-40db-b3d3-6265c00fbd3e._msdcs.domain1.local) couldn't be resolved, the server name (srv.domain1.local) resolved to the IP address (192.168.1.21) and was pingable. Check that the IP address is registered correctly with the DNS server. ......................... SRV failed test Connectivity Doing primary tests Testing server: Default-First-Site-Name\SRV Skipping all tests, because server SRV is not responding to directory service requests Running partition tests on : ForestDnsZones Starting test: CrossRefValidation ......................... ForestDnsZones passed test CrossRefValidation Starting test: CheckSDRefDom ......................... ForestDnsZones passed test CheckSDRefDom Running partition tests on : DomainDnsZones Starting test: CrossRefValidation ......................... DomainDnsZones passed test CrossRefValidation Starting test: CheckSDRefDom ......................... DomainDnsZones passed test CheckSDRefDom Running partition tests on : Schema Starting test: CrossRefValidation ......................... Schema passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Schema passed test CheckSDRefDom Running partition tests on : Configuration Starting test: CrossRefValidation ......................... Configuration passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Configuration passed test CheckSDRefDom Running partition tests on : domain1 Starting test: CrossRefValidation ......................... domain1 passed test CrossRefValidation Starting test: CheckSDRefDom ......................... domain1 passed test CheckSDRefDom Running enterprise tests on : domain1.local Starting test: Intersite ......................... domain1.local passed test Intersite Starting test: FsmoCheck ......................... domain1.local passed test FsmoCheck from previous postings, I've tried adding the domain suffix to the nic ip properties to both the client machine and the dc server which didn't help. note: there is only one nic on the server any ideas? thanks in advance

    Read the article

  • WDS DHCP same server on Windows Server 2008

    - by Richard
    I have been struggling with a problem on my Windows Server 2008 for the past 4 - 5 hours and cannot figure out whats wrong. I have tried pretty much everything that I found on google and all the links are purple. Hopefully you guys can help me. I am running a Windows Server 2008 Standard edition with the latest updates as of today. Furthermore I am running a Windows Server 2003. Both are virtual machines on my ESXi 5 server. My network is: 192.168.10.0/24 W2k8: 192.168.10.251 is the PDC running ADS, DHCP and WDS W2k3: 192.168.10.253 AND 192.168.1.175 running Routing and Remote Access and ISA 2006 Enterprise In my internal network (192.168.10.0/24) I have my client machine (192.168.10.10) that runs a VMWare Workstation. I am trying to deploy Windows 7 Home Premium to a virtual machine on my VMWorkstation via PXE. I have set the Workstation's VM network adapter to "bridged" so that it uses the physical network adapter and is connected to my internal network. The DHCP pool is configured to give IP addresses from 192.168.10.10-192.168.10.15 (works for normal clients and is not used up) When I start my VM with the PXE I get the error: PXE-E52:proxyDHCP offers were received. No DHCP offers were received Apperently this means "that means that WDS responded but the DHCP server did not." People suggested to direct the traffic to both WDS and DHCP on the router, since everything is on the same subnet there is no need for that as the broadcast is seen by everyone (WDS and DHCP) No reservation for the virtual mac addrs is made on the DHCP. Furthermore it was suggested to configure the DHCP options: Option 60= PXEClient Option 66= WDS server name or IP address Option 67= Boot file name However, this is not recommended by Microsoft, I tried it and it did not solve my problem. The configuration on the WDS (My System is German therefore the actual naming might be different): PXE response tab: PXE responses is set to "ALL (known and unknown)" DHCP Tab: Do not listen to port 67 is NOT ticked - if I tick this I do not get any responses and the PXE errors gets PXE-E51 that neither DHCP or proxyDHCP were received DHCP-Option 60 for "PXEClient" is ticked The confusing part here is that it is advised in the tab to tick the first option since it is on the same server. Network Configuration Tab: Use the following IP-Address range for Multicast-IP-Address: 224.0.1.0 - 224.0.10.0 Thats not the default one, however it is in the allowed range. The UDP port range is the default since it is not advised to change them. I tried to change the "networkprofile" from 100mbits/1gbits and custom. I am running a 1gbit network with CAT6 cables and 1gbit netgear switch 5 ports. Everything is configured to use 1gbit. The WDS is authorised for the DHCP server. My ISA 2006 configuration: For the internal networking i have configured the following policy array: Allow protocols on internal network including the w2k3 host: 67,68,53,ICMP, 4011 UDP receive, 64001-6500 UDP send receive, 69 UDP send Routing and Remote Access I tried the DHCP relay agent configuration that was suggested as well, but that did not work I would highly appreciate anykind of help because I am pretty much done here with my nerves. Thank you very much in advance.

    Read the article

  • Strange enduser experience with Liferay, Glassfish and Apache on RedHat

    - by Pete Helgren
    Tried multiple forums to get to the bottom of this. I hope I can get some direction here: Here is the stack I am working with: Red Hat Enterprise Linux Server release 5.6 (Tikanga) Liferay 6.0.6 on Glassfish 3.0.1 MySQL 5.0.77 Apache 2.2.3 The Liferay portal provides a variety of portlets to end users. Static content (web pages), static resources (primarily pdf and mp3 files 1mb - 80mb in size), File upload and download capabilities (primarily 40-60mb mp3 files) and online streaming of those MP3 files. Here is the strange end user experiences: Under normal load: (20-30) users uploading, downloading or streaming files and 20-30 accessing static content (some of it downloads), we see the following: 1) Clicking a link triggers the download of a portion of an MP3 (the portion is a few seconds long). 2) Clicking on a link tiggers the download of the page content rather than rendering. 3) Clicking a link causes the page to dump binary data to the end user rather than the expected content. 4) Clicking a link returns the text of a javascript file rather than rendering the page. Each occurrence is totally random (or appears so). Sometimes it works, sometimes it doesn't. It seems to have no relation to browser or client OS. The strange events seem to occur much more frequently when using an SSL connection rather than regular http. Apache serves as a proxy server only (reverse). It basically passes all the requests through to Glassfish. There isn't any static content proxy served by Apache. We rebuilt the entire stack from scratch and redeployed the portlet wars and still have the same issues. Liferay is running as a single server (not clustered). We disabled mod_cache in Apache. The problems are more frequent as the server load grows. This morning the load is pretty light and we are seeing few problems but the use of the site will grow, particularly tonight around 9pm CST through Wednesday morning. You could try the site (http://preview.bsfinternational.org) during those times and I would expect that you might experience one of the weirdnesses as you randomly click links on the site (https is invoked only when signed in). Again, https seems to exacerbate the issue. This seems very much like a caching issue but I don't know where in the stack to start peeling the onion. Apache? Liferay? Glassfish? MySQL? Maybe even Redhat? We are stumped and most forums we have posted to (LifeRay and Glassfish) have returned very few suggestions. I just need an idea of where to start looking. I understand that we could have a portlet EDIT: Opening the files in a Hex editor that appear to be pages that download rather than render, we see that the first 4000 characters are "junk" and then the "HTTP/1.1 ...." 'normal' header is seen. So something is dumping a jumble of characters up to offset 4000 (when viewing it in a Hex editor). Perhaps a clue? Ideas?

    Read the article

  • Strange Upload Problem on Hyper-V

    - by Ring0
    Hi, This one is driving me totally nuts. I have being trying to upload a file to www.virustotal.com (its a harmless exe I have since found out - DiskWipe.exe from diskwipe.org). Using IE8. From Win 7 and Win 2008 R2 Datacenter (which I select to boot from vhd's) onto my main machine hardware, and also on another Win 7 PC elsewhere on my network, when I upload the file to virustotal.com it works perfectly. So, using my native NIC's everything is fine. Using another machine also perfect. Right. OK, from my boot menu the default is my main development machine - the one I'm typing on now. This runs on the metal and has Hyper-V role and I have some guests. All guests are not running. Amazingly, from my console (root partition to be exact) or any guest OS 2003 /XP / 2008 R2 etc. My upload to virustotal.com slows at 32% then HANGS at 38.something% & never finishes!! Here is the kicker. I have another box (my main server) running Hyper-V on the metal and three live guests. Identical H/W to my main dev machine in another room. (Except OS is Datacenter - Mine is Enterprise). If I try and upload from its bare metal console or any guest this file to virustotal.com using IE8 it stops exactly in the same place!! As for "steps I have tried etc." are kind-of blown out of the water as my server box is doing the precise same thing as the machine in my room here. OK, comonalities: Mobo: Gigabyte GA-X58-UD5, 12GB Kingston RAM, Corei7 920 4 cores hyperthreading = 8 & Realtek RTL8168D/8111D Family PCI-E Gigabit Ethernet NIC's. All 3 machines have this same motherboard - revision F11 Bios, all have 12GB RAM, all have the Realtek Nic's. All x64 by the way as I mentioned before I have a Win 7 box also with the UD5 m/Board, 12 GB RAM - bit of an overkill. :-) All these machines when NOT running Hyper-V can upload this file. Perhaps you may like to try it on a Hyepr-v (2008 R2) yourselves with IE8 and the desktop experience is on. See if it works or fails for you. Root OS or any guest. So, looking like its the NIC + Hyper-V = Cannot upload this file (any file I must add.) Realtek Nic is Ver 7.002.1125.2008. Using IE8 I see in the nic settings there are the usual parameters for Jumbo frames / Checksum offloading etc. several others. Should I fiddle with these? I ran Netmon 3.3 in a guest and the TCP session halted as the upload failed. I suppose I could study that further. I dont have Netmon on the root partition machine (yet)! All OS's fully patched - including todays defender files. My box running Office 2007 - but identical server in another room is not. Also, if I fire up a VPN to a distant client and do the upload it works! Of course its a different network path. Suggestions welcome please. If I left out anything important - please yell at me. Many Thanks,

    Read the article

  • apache2.2 + php5 , process never die and stay blocked to LOCK_SH

    - by Givre
    Server version: Apache/2.2.22 (Unix) Server built: Mar 28 2012 16:31:45 Server's Module Magic Number: 20051115:30 Server loaded: APR 1.4.6, APR-Util 1.4.1 Compiled using: APR 1.4.6, APR-Util 1.4.1 Architecture: 64-bit Server MPM: Prefork threaded: no forked: yes (variable process count) Server compiled with.... -D APACHE_MPM_DIR="server/mpm/prefork" -D APR_HAS_SENDFILE -D APR_HAS_MMAP -D APR_HAVE_IPV6 (IPv4-mapped addresses enabled) -D APR_USE_SYSVSEM_SERIALIZE -D APR_USE_PTHREAD_SERIALIZE -D SINGLE_LISTEN_UNSERIALIZED_ACCEPT -D APR_HAS_OTHER_CHILD -D AP_HAVE_RELIABLE_PIPED_LOGS -D DYNAMIC_MODULE_LIMIT=128 -D HTTPD_ROOT="/opt/apache2" -D SUEXEC_BIN="/opt/apache2/bin/suexec" -D DEFAULT_PIDLOG="logs/httpd.pid" -D DEFAULT_SCOREBOARD="logs/apache_runtime_status" -D DEFAULT_LOCKFILE="logs/accept.lock" -D DEFAULT_ERRORLOG="logs/error_log" -D AP_TYPES_CONFIG_FILE="conf/mime.types" -D SERVER_CONFIG_FILE="conf/httpd.conf" Php5.2.17. Using mod_php5 as a DSO module compiled Problem: On shared webhosting, a lot of apache2 process never stop or die and they waiting as long as apache2 restart. Strace of one of theses process: access("tmp/meta_cache.txt", F_OK) = 0 getcwd("/home/exemple.com/htdocs"..., 4096) = 34 lstat("/var", {st_mode=S_IFDIR|0755, st_size=4096, ...}) = 0 lstat("/var/www", {st_mode=S_IFDIR|0755, st_size=4096, ...}) = 0 lstat("/home", {st_mode=S_IFDIR|0755, st_size=1715, ...}) = 0 lstat("/home/exemple.com", {st_mode=S_IFDIR|0755, st_size=16, ...}) = 0 lstat("/home/exemple.com/htdocs", {st_mode=S_IFDIR|0770, st_size=51, ...}) = 0 lstat("/home/exemple.com/htdocs/tmp", {st_mode=S_IFDIR|0777, st_size=51, ...}) = 0 lstat("/home/exemple.com/htdocs/tmp/meta_cache.txt", {st_mode=S_IFREG|0666, st_size=8901, ...}) = 0 lstat("/var", {st_mode=S_IFDIR|0755, st_size=4096, ...}) = 0 lstat("/var/www", {st_mode=S_IFDIR|0755, st_size=4096, ...}) = 0 lstat("/home", {st_mode=S_IFDIR|0755, st_size=1715, ...}) = 0 lstat("/home/exemple.com", {st_mode=S_IFDIR|0755, st_size=16, ...}) = 0 lstat("/home/exemple.com/htdocs", {st_mode=S_IFDIR|0770, st_size=51, ...}) = 0 lstat("/home/exemple.com/htdocs/tmp", {st_mode=S_IFDIR|0777, st_size=51, ...}) = 0 lstat("/home/exemple.com/htdocs/tmp/meta_cache.txt", {st_mode=S_IFREG|0666, st_size=8901, ...}) = 0 lstat("/var", {st_mode=S_IFDIR|0755, st_size=4096, ...}) = 0 lstat("/var/www", {st_mode=S_IFDIR|0755, st_size=4096, ...}) = 0 lstat("/home", {st_mode=S_IFDIR|0755, st_size=1715, ...}) = 0 lstat("/home/exemple.com", {st_mode=S_IFDIR|0755, st_size=16, ...}) = 0 getcwd("/home/exemple.com/htdocs"..., 4096) = 34 lstat("/var", {st_mode=S_IFDIR|0755, st_size=4096, ...}) = 0 lstat("/var/www", {st_mode=S_IFDIR|0755, st_size=4096, ...}) = 0 lstat("/home", {st_mode=S_IFDIR|0755, st_size=1715, ...}) = 0 lstat("/home/exemple.com", {st_mode=S_IFDIR|0755, st_size=16, ...}) = 0 lstat("/home/exemple.com/htdocs", {st_mode=S_IFDIR|0770, st_size=51, ...}) = 0 lstat("/home/exemple.com/htdocs/tmp", {st_mode=S_IFDIR|0777, st_size=51, ...}) = 0 lstat("/home/exemple.com/htdocs/tmp/meta_cache.txt", {st_mode=S_IFREG|0666, st_size=8901, ...}) = 0 open("/home/exemple.com/htdocs/tmp/meta_cache.txt", O_RDONLY) = 10905 fstat(10905, {st_mode=S_IFREG|0666, st_size=8901, ...}) = 0 lseek(10905, 0, SEEK_CUR) = 0 flock(10905, LOCK_SH) = The process never die, and stay like this. All files are on NFS V3 I'dont know how to solve this problem or find more informations. The effect is that all apache2 process become used and apache2 crash totaly . Thanks for you help.

    Read the article

  • redhat Apache fast-cgi selinux permissions

    - by Alejo JM
    My apache installation is running php as fastcgi, and the virtual hosts are pointing to /home/*/public_html. and the fastcgi are home/*/cgi-bin/php.fcgi the public_html setup with selinux was: /usr/sbin/setsebool -P httpd_enable_homedirs 1 chcon -R -t httpd_sys_content_t /home/someuser/public_html The owner and group are the user, for example the user "someuser": ls -all /home/someuser/cgi-bin/ drwxr-xr-x 2 someuser someuser 4096 Sep 7 13:14 . drwx--x--x 6 someuser someuser 4096 Sep 6 18:17 .. -rwxr-xr-x 1 someuser someuser 308 Sep 7 13:14 php.fcgi ls -all /home/someuser/public_html/ | greep info.php -rw-r--r-- 1 someuser someuser 24 Sep 3 16:24 info.php When is visits the site I get "Forbidden ..." and the log said: [Fri Sep 07 12:02:51 2012] [error] [client x.x.x.x] (13)Permission denied: access to /cgi-bin/php.fcgi/info.php denied My selinux conf is: SELINUX=enforcing SELINUXTYPE=targeted SETLOCALDEFS=0 So I kill Selinux (SELINUX=disabled), reboot the system and everything works !!!!! The problem is Selinux, I don't want disable Selinux. I trying this with no success: setsebool -P httpd_enable_cgi 1 chcon -t httpd_sys_script_exec_t /home/someuser/cgi-bin/php.fcgi chcon -R -t httpd_sys_content_t /home/someuser/cgi-bin Or maybe is better change Selinux SELINUX=enforcing to SELINUX=permissive And disable selinux for httpd ? (I think I better find the correct configuration) Thanks for any suggestion on this matter My environment: Red Hat Enterprise Linux Server release 5.8 (Tikanga) Server version: Apache/2.2.3 PHP 5.1.6 (cli) (built: Jun 22 2012 06:20:25) Copyright (c) 1997-2006 The PHP Group Zend Engine v2.1.0, Copyright (c) 1998-2006 Zend Technologies Some logs: ps -ZC httpd LABEL PID TTY TIME CMD system_u:system_r:httpd_t 2822 ? 00:00:00 httpd system_u:system_r:httpd_t 2823 ? 00:00:00 httpd system_u:system_r:httpd_t 2824 ? 00:00:00 httpd system_u:system_r:httpd_t 2825 ? 00:00:00 httpd system_u:system_r:httpd_t 2826 ? 00:00:00 httpd system_u:system_r:httpd_t 2836 ? 00:00:00 httpd system_u:system_r:httpd_t 2837 ? 00:00:00 httpd system_u:system_r:httpd_t 2838 ? 00:00:00 httpd system_u:system_r:httpd_t 2839 ? 00:00:00 httpd system_u:system_r:httpd_t 2840 ? 00:00:00 httpd getsebool -a | grep httpd allow_httpd_anon_write --> off allow_httpd_bugzilla_script_anon_write --> off allow_httpd_cvs_script_anon_write --> off allow_httpd_mod_auth_pam --> off allow_httpd_nagios_script_anon_write --> off allow_httpd_prewikka_script_anon_write --> off allow_httpd_squid_script_anon_write --> off allow_httpd_sys_script_anon_write --> off httpd_builtin_scripting --> on httpd_can_network_connect --> off httpd_can_network_connect_db --> off httpd_can_network_relay --> off httpd_can_sendmail --> on httpd_disable_trans --> off httpd_enable_cgi --> on httpd_enable_ftp_server --> off httpd_enable_homedirs --> on httpd_execmem --> off httpd_read_user_content --> off httpd_rotatelogs_disable_trans --> off httpd_setrlimit --> off httpd_ssi_exec --> off httpd_suexec_disable_trans --> off httpd_tty_comm --> on httpd_unified --> on httpd_use_cifs --> off httpd_use_nfs --> off

    Read the article

  • Why are my httpd mpm_prefork processes being reaped so quickly?

    - by Dan Pritts
    We've got a system running RHEL6, x64. We are using a local installation of apache 2.2.22 from source. we serve primarily: mod_perl applications (with a local installation of perl 5.16.0) tomcat applications proxied with mod_jk Here is some context; the main question is below. All of this talks to an Oracle backend. We are having issues with Oracle becoming unresponsive. We think this is because we're hitting the maximum process limit in oracle. We've upped the process limit, but now we are hitting memory pressure on the oracle server. We have tons of oracle sessions sitting idle. I can trace a bunch of them back to the httpd processes. We have mod_perl's Apache::DBI start up a new connection to the database with each httpd child that's spawned. We are concerned that these are not always getting closed out properly when the httpd's exit...and the httpd's are exiting very frequently. I know that it would be good to modify the mod_perl applications to use some better form of db connection pooling; we plan to pursue that but would like to solve our immediate problem sooner. So here's the main question. We are using the prefork MPM. The apache child processes are lasting at most a few minutes. Log analysis shows that each one is serving fewer than 50 clients before exiting; the last request each child serves is OPTIONS * HTTP/1.0 on some sort of internal connection; I'm under the impression that this is a "ping" from the master process. I've adjusted the MPM config as follows. I didn't want to raise MinSpareServers too high, because, after all, i'm trying to minimize the number of sessions to oracle. MinSpareServers 5 MaxSpareServers 30 MaxClients 150 MaxRequestsPerChild 10000 Right now we're serving 250-300 requests per minute. We've got 21 httpd's running, the eldest (other than the master, owned by root) being 3 minutes old. This rate of reaping of the apache children really seems excessive. What could be causing it? Apache was built with: $ ./configure --prefix=/opt/apache --with-ssl=/usr/lib --enable-expires --enable-ext-filter --enable-info --enable-mime-magic --enable-rewrite --enable-so --enable-speling --enable-ssl --enable-usertrack --enable-proxy --enable-headers --enable-log-forensic Apache config info: % /opt/apache/bin/httpd -V Server version: Apache/2.2.22 (Unix) Server built: Jul 23 2012 22:30:13 Server's Module Magic Number: 20051115:30 Server loaded: APR 1.4.5, APR-Util 1.4.1 Compiled using: APR 1.4.5, APR-Util 1.4.1 Architecture: 64-bit Server MPM: Prefork threaded: no forked: yes (variable process count) Server compiled with.... -D APACHE_MPM_DIR="server/mpm/prefork" -D APR_HAS_SENDFILE -D APR_HAS_MMAP -D APR_HAVE_IPV6 (IPv4-mapped addresses enabled) -D APR_USE_SYSVSEM_SERIALIZE -D APR_USE_PTHREAD_SERIALIZE -D SINGLE_LISTEN_UNSERIALIZED_ACCEPT -D APR_HAS_OTHER_CHILD -D AP_HAVE_RELIABLE_PIPED_LOGS -D DYNAMIC_MODULE_LIMIT=128 -D HTTPD_ROOT="/opt/apache" -D SUEXEC_BIN="/opt/apache/bin/suexec" -D DEFAULT_PIDLOG="logs/httpd.pid" -D DEFAULT_SCOREBOARD="logs/apache_runtime_status" -D DEFAULT_LOCKFILE="logs/accept.lock" -D DEFAULT_ERRORLOG="logs/error_log" -D AP_TYPES_CONFIG_FILE="conf/mime.types" -D SERVER_CONFIG_FILE="conf/httpd.conf" modules are compiled into apache rather than shared libs: % /opt/apache/bin/httpd -l Compiled in modules: core.c mod_authn_file.c mod_authn_default.c mod_authz_host.c mod_authz_groupfile.c mod_authz_user.c mod_authz_default.c mod_auth_basic.c mod_ext_filter.c mod_include.c mod_filter.c mod_log_config.c mod_log_forensic.c mod_env.c mod_mime_magic.c mod_expires.c mod_headers.c mod_usertrack.c mod_setenvif.c mod_version.c mod_proxy.c mod_proxy_connect.c mod_proxy_ftp.c mod_proxy_http.c mod_proxy_scgi.c mod_proxy_ajp.c mod_proxy_balancer.c mod_ssl.c prefork.c http_core.c mod_mime.c mod_status.c mod_autoindex.c mod_asis.c mod_info.c mod_cgi.c mod_negotiation.c mod_dir.c mod_actions.c mod_speling.c mod_userdir.c mod_alias.c mod_rewrite.c mod_so.c One final note - the red hat httpd, apr, and perl packages are all installed, but ldd shows that none of those libraries are linked with the running httpd.

    Read the article

  • Unable to remove limit on memory usage for PHP script.

    - by Jess Telford
    The Situation I am having an issue with a PHP script getting the following error message: Fatal error: Out of memory (allocated 359923712) (tried to allocate 72 bytes) in /path/to/piwik/core/DataTable.php on line 969 The script I'm running is: /path/to/piwik/misc/cron/archive.sh I am assuming the numbers are Bytes, which means that total is approximately 360MB. For all intents and purposes, I have increased the memory limits on the server well above 360MB, yet this is the number (give or take a byte) it consistently errors out at. Please note: This question is not about fixing a memory leak in the script, nor about why the script itself is using so much memory. The script is part of the Piwik archiving process, so I cannot just fix any memory leaks, etc. For more info on this script and why I am increasing the memory limit, see "How to setup auto archiving" The question Given that the script is attempting to use over 360MB of memory, which I cannot change, why does it not seem possible for me to increase the amount of memory available to php on my server? What I've tried Increasing PHP's memory_limit Given the php.ini file: php -i | grep php.ini Configuration File (php.ini) Path => /usr/local/lib Loaded Configuration File => /usr/local/lib/php.ini I have edited that file, so the memory_limit directive reads; memory_limit = -1 Restart Apache, and check the new value has stuck; $ php -i | grep memory_limit memory_limit => -1 => -1 Run the script, and get the same error. I've also tried 1G, 768M, etc, all to the same result (ie; no change). Update 22nd June: Based on Vangel's help, I have attempted to set post_max_size to 20M in combination with setting memory_limit. Again, this has no effect. Removing the memory limit on child processes of Apache I have found and edited the httpd.conf file to make sure there is no RLimitMEM directive. I then used WHM's Apache Configuration Memory Usage Restrictions to generate a restriction, which it claimed was at 1000M (and confirmed by checking httpd.conf). Both of these resulted in no change to the script erroring at 360MB. Increasing the per process memory limits of Linux The current limits set on the system: $ ulimit -m 524288 $ ulimit -v 524288 I have attempted to set both of these to unlimited: $ ulimit -m unlimited $ ulimit -v unlimited $ ulimit -m unlimited $ ulimit -v unlimited Once again, this has resulted in absolutely no improvement in my problem. My setup $ cat /etc/redhat-release CentOS release 5.5 (Final) $ uname -a Linux example.com 2.6.18-164.15.1.el5 #1 SMP Wed Mar 17 11:30:06 EDT 2010 x86_64 x86_64 x86_64 GNU/Linux $ php -i | grep "PHP Version" PHP Version => 5.2.9 $ httpd -V Server version: Apache/2.0.63 Server built: Feb 2 2011 01:25:12 Cpanel::Easy::Apache v3.2.0 rev5291 Server's Module Magic Number: 20020903:13 Server loaded: APR 0.9.17, APR-UTIL 0.9.15 Compiled using: APR 0.9.17, APR-UTIL 0.9.15 Architecture: 64-bit Server compiled with.... -D APACHE_MPM_DIR="server/mpm/prefork" -D APR_HAS_SENDFILE -D APR_HAS_MMAP -D APR_HAVE_IPV6 (IPv4-mapped addresses enabled) -D APR_USE_SYSVSEM_SERIALIZE -D APR_USE_PTHREAD_SERIALIZE -D SINGLE_LISTEN_UNSERIALIZED_ACCEPT -D APR_HAS_OTHER_CHILD -D AP_HAVE_RELIABLE_PIPED_LOGS -D HTTPD_ROOT="/usr/local/apache" -D SUEXEC_BIN="/usr/local/apache/bin/suexec" -D DEFAULT_PIDLOG="logs/httpd.pid" -D DEFAULT_SCOREBOARD="logs/apache_runtime_status" -D DEFAULT_LOCKFILE="logs/accept.lock" -D DEFAULT_ERRORLOG="logs/error_log" -D AP_TYPES_CONFIG_FILE="conf/mime.types" -D SERVER_CONFIG_FILE="conf/httpd.conf" Output of $ php -i: http://pastebin.com/EiRut6Nm

    Read the article

  • An error occured synchronizing windows with time.windows.com

    - by Killrawr
    Okay so I've tried stopping/registering the win32tm service on this Windows Server 2008 Enterprise Computer. C:\Users\Administrator>net stop w32time The Windows Time service is stopping. The Windows Time service was stopped successfully. C:\Users\Administrator>w32tm /unregister The following error occurred: Access is denied. (0x80070005) C:\Users\Administrator>w32tm /unregister W32Time successfully unregistered. C:\Users\Administrator>w32tm /register W32Time successfully registered. C:\Users\Administrator>net start w32time The Windows Time service is starting. The Windows Time service was started successfully. (Source : http://social.technet.microsoft.com/Forums/en-US/winserverDS/thread/9bdfc2cc-4775-4435-8868-57d214e1e3ba/) And I get this error from the Date and Time, Internet Time tab (After also following the steps here). I've even tried the Atomic Time Clock Worldtimeserver and I get the error The following error occurred: The specified module could not be found. (0x8007007E). I've also disabled the Windows Firewall, that might of been blocking the synchronization. I've done a file scan with sfc /scannow that came back with no errors. C:\Users\Administrator>sfc /scannow Beginning system scan. This process will take some time. Beginning verification phase of system scan. Verification 100% complete. Windows Resource Protection did not find any integrity violations. C:\Users\Administrator> But I'm not having much luck. Is there anyway lo possibly solve this? or is the time.windows.com servers unsupported? because the software is from 2008? (I really don't know :/), My ping result to time.windows.com C:\Users\Administrator>ping time.windows.com Pinging time.microsoft.akadns.net [65.55.21.22] with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for 65.55.21.22: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), And tracert result C:\Users\Administratortracert time.windows.com Tracing route to time.microsoft.akadns.net [65.55.21.24] over a maximum of 30 hops: 1 1 ms <1 ms <1 ms 192.168.1.1 2 32 ms 31 ms 32 ms be2-100.bras1wtc.wlg.vf.net.nz [203.109.129.113] 3 31 ms 32 ms 31 ms be5-100.ppnzwtc01.wlg.vf.net.nz.129.109.203.in-a ddr.arpa [203.109.129.114] 4 31 ms 31 ms 31 ms gi0-2-0-3.ppnzwtc01.wlg.vf.net.nz.180.109.203.in -addr.arpa [203.109.180.210] 5 31 ms 31 ms 30 ms gi0-2-0-3.ppnzwtc02.wlg.vf.net.nz [203.109.180.2 09] 6 167 ms 166 ms 166 ms ip-141.199.31.114.VOCUS.net.au [114.31.199.141] 7 175 ms 175 ms 175 ms microsoft.com.any2ix.coresite.com [206.223.143.1 43] 8 177 ms 180 ms 176 ms xe-7-0-2-0.by2-96c-1a.ntwk.msn.net [207.46.42.17 6] 9 205 ms 205 ms 204 ms xe-10-0-2-0.co1-96c-1b.ntwk.msn.net [207.46.45.3 1] 10 * * * Request timed out. 11 * * * Request timed out. 12 * * * Request timed out. 13 * * * Request timed out. 14 * * * Request timed out. 15 * * * Request timed out. 16 ^C And nslookup C:\Users\Administrator>nslookup time.windows.com Server: UnKnown Address: 192.168.1.1 Non-authoritative answer: Name: time.microsoft.akadns.net Address: 65.55.21.22 Aliases: time.windows.com

    Read the article

  • CPU Utilization LAMP stack

    - by Max
    We've got an ec2 m2.4xlarge running Magento (centos 5.6, httpd 2.2, php 5.2.17 with eaccelerator 0.9.5.3, mysql 5.1.52). Right now we're getting a large traffic spike, and our top looks like this: top - 09:41:29 up 31 days, 1:12, 1 user, load average: 120.01, 129.03, 113.23 Tasks: 1190 total, 18 running, 1172 sleeping, 0 stopped, 0 zombie Cpu(s): 97.3%us, 1.8%sy, 0.0%ni, 0.5%id, 0.0%wa, 0.0%hi, 0.0%si, 0.4%st Mem: 71687720k total, 36898928k used, 34788792k free, 49692k buffers Swap: 880737784k total, 0k used, 880737784k free, 1586524k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 2433 mysql 15 0 23.6g 4.5g 7112 S 564.7 6.6 33607:34 mysqld 24046 apache 16 0 411m 65m 28m S 26.4 0.1 0:09.05 httpd 24360 apache 15 0 410m 60m 25m S 26.4 0.1 0:03.65 httpd 24993 apache 16 0 410m 57m 21m S 26.1 0.1 0:01.41 httpd 24838 apache 16 0 428m 74m 20m S 24.8 0.1 0:02.37 httpd 24359 apache 16 0 411m 62m 26m R 22.3 0.1 0:08.12 httpd 23850 apache 15 0 411m 64m 27m S 16.8 0.1 0:14.54 httpd 25229 apache 16 0 404m 46m 17m R 10.2 0.1 0:00.71 httpd 14594 apache 15 0 404m 63m 34m S 8.4 0.1 1:10.26 httpd 24955 apache 16 0 404m 50m 21m R 8.4 0.1 0:01.66 httpd 24313 apache 16 0 399m 46m 22m R 8.1 0.1 0:02.30 httpd 25119 apache 16 0 411m 59m 23m S 6.8 0.1 0:01.45 httpd Questions: Would giving msyqld more memory help it cache queries and react faster? If so, how? Other than splitting mysql and php to separate servers (which we're about to do) is there anything else we could/should be doing? Thanks! UPDATE: Here's our my.cnf along with the output of mysqltuner. It looks like a cache problem. Thanks again! # cat /etc/my.cnf [client] port = **** socket = /var/lib/mysql/mysql.sock [mysqld] datadir=/mnt/persistent/mysql port=**** socket=/var/lib/mysql/mysql.sock key_buffer = 512M max_allowed_packet = 64M table_cache = 1024 sort_buffer_size = 8M read_buffer_size = 4M read_rnd_buffer_size = 2M myisam_sort_buffer_size = 64M thread_cache_size = 128M tmp_table_size = 128M join_buffer_size = 1M query_cache_limit = 2M query_cache_size= 64M query_cache_type = 1 max_connections = 1000 thread_stack = 128K thread_concurrency = 48 log-bin=mysql-bin server-id = 1 wait_timeout = 300 innodb_data_home_dir = /mnt/persistent/mysql/ innodb_data_file_path = ibdata1:10M:autoextend innodb_buffer_pool_size = 20G innodb_additional_mem_pool_size = 20M innodb_log_file_size = 64M innodb_log_buffer_size = 8M innodb_flush_log_at_trx_commit = 1 innodb_lock_wait_timeout = 50 innodb_thread_concurrency = 48 ft_min_word_len=3 [myisamchk] ft_min_word_len=3 key_buffer = 128M sort_buffer_size = 128M read_buffer = 2M write_buffer = 2M # ./mysqltuner.pl >> MySQLTuner 1.2.0 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.52-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB +Federated +InnoDB -ISAM -NDBCluster [--] Data in MyISAM tables: 2G (Tables: 26) [--] Data in InnoDB tables: 749M (Tables: 250) [!!] Total fragmented tables: 262 -------- Security Recommendations ------------------------------------------- -------- Performance Metrics ------------------------------------------------- [--] Up for: 31d 2h 30m 38s (680M q [253.371 qps], 2M conn, TX: 4825B, RX: 236B) [--] Reads / Writes: 89% / 11% [--] Total buffers: 20.6G global + 15.1M per thread (1000 max threads) [OK] Maximum possible memory usage: 35.4G (51% of installed RAM) [OK] Slow queries: 0% (35K/680M) [OK] Highest usage of available connections: 53% (537/1000) [OK] Key buffer size / total MyISAM indexes: 512.0M/457.2M [OK] Key buffer hit rate: 100.0% (9B cached / 264K reads) [OK] Query cache efficiency: 42.3% (260M cached / 615M selects) [!!] Query cache prunes per day: 4384652 [OK] Sorts requiring temporary tables: 0% (1K temp sorts / 38M sorts) [!!] Joins performed without indexes: 100404 [OK] Temporary tables created on disk: 17% (7M on disk / 45M total) [OK] Thread cache hit rate: 99% (537 created / 2M connections) [!!] Table cache hit rate: 0% (1K open / 946K opened) [OK] Open file limit used: 9% (453/5K) [OK] Table locks acquired immediately: 99% (758M immediate / 758M locks) [OK] InnoDB data size / buffer pool: 749.3M/20.0G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance Enable the slow query log to troubleshoot bad queries Adjust your join queries to always utilize indexes Increase table_cache gradually to avoid file descriptor limits Variables to adjust: query_cache_size (> 64M) join_buffer_size (> 1.0M, or always use indexes with joins) table_cache (> 1024)

    Read the article

  • Looking for advice on Hyper-v storage replication

    - by Notre1
    I am designing a 2-host Hyper-V R2 cluster with 6-10 guests stored on a SMB iSCSI SAN device (probably Promise VessRAID). I will be getting at least two of the SAN devices and need to eliminate the storage a single point of failure. Ideally, that would involve real-time failover for the storage, like the Windows failover clustering does for the hosts. This design will be used at around six of our sites, and I would like to allow for us to eventually setup a cluster at colocation site and replicate each site's VMs there for DR. (Ideally a live multi-site cluster, but a manual import of the VMs would be fine for this sort of DR.) The tools that come with enterprise SANs, like EMC and NetApp, seem to be the most commonly used items for a Hyper-V cluster, but I can't afford their prices with my budget. Outside of them, the two tools that seem to be most common for Hyper-V storage replication are SteelEye (now SIOS) DataKeeper Cluster Edition and Double-Take Availability. Originally, I was planning on using Clustered Shared Volume(s) (CSV), but it seems like replication support for these is either not available or brand new in both these products. It looks like CSVs are supported in Double-Take 5.22, see this discussion, but I don't think I want to run something that new in production. Right now, it seems like the best option for me is not to implement CSVs, implement some sort of storage replication, and upgrade to CSVs at a later date once replicating them is more mature. I would love to have live migration, and CSVs are not required for live migration if you are using one LUN per VM, so I guess this is what I'll do. I would prefer to stick to the using the Microsoft Windows Server and Hyper-V tools and features as much as possible. From that standpoint, SteelEye looks more appealing than Double-Take because they make the DataKeeper volume(s) available to the Failover Clustering Manager and then failover clustering is all configured and managed through the native Microsoft tools. Double-Take says that "clustered Hyper-V hosts are not supported," and Double-Take Availability itself seems to be what is used for the actual clustering and failover. Does anyone know if any of these replication tools work with more than two hosts in the cluster? All the information I can find on the web only uses two hosts in their examples. Are there any better tools than SteelEye and Double-Take for doing what I am trying to do, which is eliminate the storage as as single point of failure? Neverfail, AppAssure, and DataCore all seem to offer similar functionality, but they don't seems to be as popular as SteelEye and Double-Take. I have seen a number of people suggest using Starwind iSCSI SAN software for the shared storage, which includes replication (and CSV replication at that). There are a couple of reasons I have not seriously considered this route: 1) The company I work for is exclusively a Dell shop and Dell does not have any servers with that I can pack with more than six 3.5" SATA drives. 2) In the future, it could be advantegous for us to not be locked into a particular brand or type of storage and third-party replication softwares all allow replication to heterogeneous storage devices. I am pretty new to iSCSI and clustering, so please let me know if it looks like I am planning something that goes against best practices or overlooking/missing something.

    Read the article

  • how to use ajax with json in ruby on rails

    - by rafik860
    I am implemeting a facebook application in rails using facebooker plugin, therefore it is very important to use this architecture if i want to update multiple DOM in my page. if my code works in a regular rails application it would work in my facebook application. i am trying to use ajax to let the user know that the comment was sent, and update the comments bloc. migration: class CreateComments < ActiveRecord::Migration def self.up create_table :comments do |t| t.string :body t.timestamps end end def self.down drop_table :comments end end controller: class CommentsController < ApplicationController def index @comments=Comment.all end def create @comment=Comment.create(params[:comment]) if request.xhr? @comments=Comment.all render :json=>{:ids_to_update=>[:all_comments,:form_message], :all_comments=>render_to_string(:partial=>"comments" ), :form_message=>"Your comment has been added." } else redirect_to comments_url end end end view: <script> function update_count(str,message_id) { len=str.length; if (len < 200) { $(message_id).innerHTML="<span style='color: green'>"+ (200-len)+" remaining</span>"; } else { $(message_id).innerHTML="<span style='color: red'>"+ "Comment too long. Only 200 characters allowed.</span>"; } } function update_multiple(json) { for( var i=0; i<json["ids_to_update"].length; i++ ) { id=json["ids_to_update"][i]; $(id).innerHTML=json[id]; } } </script> <div id="all_comments" > <%= render :partial=>"comments/comments" %> </div> Talk some trash: <br /> <% remote_form_for Comment.new, :url=>comments_url, :success=>"update_multiple(request)" do |f|%> <%= f.text_area :body, :onchange=>"update_count(this.getValue(),'remaining');" , :onkeyup=>"update_count(this.getValue(),'remaining');" %> <br /> <%= f.submit 'Post'%> <% end %> <p id="remaining" >&nbsp;</p> <p id="form_message" >&nbsp;</p> <br><br> <br> if i try to do alert(json) in the first line of the update_multiple function , i got an [object Object]. if i try to do alert(json["ids_to_update"][0]) in the first line of the update_multiple function , there is no dialog box displayed. however the comment got saved but nothing is updated. it seems like the object sent by rails is nil or cant be parsed by JSON.parse(json). questions: 1.how can javascript and rails know that i am dealing with json objects?deos ROR sent it a object format or a text format?how can it check that the json object has been sent 2.how can i see what is the returned json?do i have to parse it?how? 2.how can i debug this problem? 3.how can i get it to work?

    Read the article

  • Supermicro IPMI on MBD-X8DAH+-F-O motherboard. Keyboard and mouse do not work after booting Windows Server 2008 R2

    - by LDelgado
    Hell Everyone, I built a server with the mentioned motherboard. I installed Windows Server 2008 R2 Enterprise on this server. IPMI is integrated on the motherboard with its own dedicated NIC. I've got that NIC configured with its own IP address. I can remote into it using IPMI, and I can remotely control the server settings before booting the OS ( BIOS, RAID configuration, etc). When the OS boots, I lose the mouse and keyboard. I cannot use the keyboard or mouse when installing the OS either. So the Keyboard and Mouse only work when no OS is loaded. Once the OS loads I lose it - that is my problem. I've been doing some research and trying a few things, but I have not been successful in fixing this issue. I may be wrong, but based on the things I've found online, it seems that the problem could be caused by the way the OS handles USB. The server is headless. There is no keyboard, mouse, or monitor plugged into it. When I boot up the OS and remote into it, I cannot see a mouse or keyboard listed in the Device Manager. Based on what I've read, it seems that the OS should detect a mouse and a keyboard when connecting remotely via IPMI. The following are the solutions I've tried. Nothing has worked so far: I've updated the firmware of the IPMI component to the latest firmware - 1.33. I made sure that the mouse mode was set to Absolute (Windows OS). I've loaded the factory defaults several times. I've enabled Port64h/60h Emulation under the USB settings in the BIOS. I've disabled USB legacy support in the BIOS. I made sure the firewall wasn't blocking IPMI (disabled the firewall). And that's about it. I've found threads in some forums from people having the same issue as me, but they were not running the same OS. They were either running Linux or FreeBSD. Most of them fixed their problem by selecting the right mouse mode (Linux in their case). There was one other that solved the problem by disabling USB Mass Storage mode. He stated "When I set it to disable USB Mass Storage when no image is loaded, the ukbd came alive, and I'm typing this on the IPMI Console. " source: http://freebsd.1045724.n5.nabble.com/IPMI-Console-No-luck-once-OS-is-booted-td3967868.html I suspect the solution described in the previous paragraph is somehow related to my problem. I've found several threads on the internet with issues describing the same problem, but none of them were with Windows Server 2008 R2. Again, I may be wrong, but it seems like that could be the issue. I just don't know how I go about applying a solution in Windows Server 2008 R2. In any case, I could use your expertise. Maybe I am missing something, or maybe I'm on the right track. Your help is much appreciated. Thank you in advance,

    Read the article

  • How can I check if PHP was compiled with the UNICODE version of the Win32 API?

    - by Wesley Murch
    This is related to this Stack Overflow post: glob() can't find file names with multibyte characters on Windows? I'm having issues with PHP and files that have multibyte characters on Windows. Here's my test case: print_r(scandir('./uploads/')); print_r(glob('./uploads/*')); Correct Output on remote UNIX server: Array ( [0] => . [1] => .. [2] => filename-äöü.jpg [3] => filename.jpg [4] => test?test.jpg [5] => ??? ?????.jpg [6] => ?????????.jpg [7] => ???.jpg ) Array ( [0] => ./uploads/filename-äöü.jpg [1] => ./uploads/filename.jpg [2] => ./uploads/test?test.jpg [3] => ./uploads/??? ?????.jpg [4] => ./uploads/?????????.jpg [5] => ./uploads/???.jpg ) Incorrect Output locally on Windows: Array ( [0] => . [1] => .. [2] => ??? ?????.jpg [3] => ???.jpg [4] => ?????????.jpg [5] => filename-äöü.jpg [6] => filename.jpg [7] => test?test.jpg ) Array ( [0] => ./uploads/filename-äöü.jpg [1] => ./uploads/filename.jpg ) Here's a relevant excerpt from the answer I chose to accept (which actually is a quote from an article that was posted online over 2 years ago): From the comments on this article: http://www.rooftopsolutions.nl/blog/filesystem-encoding-and-php The output from your PHP installation on Windows is easy to explain : you installed the wrong version of PHP, and used a version not compiled to use the Unicode version of the Win32 API. For this reason, the filesystem calls used by PHP will use the legacy "ANSI" API and so the C/C++ libraries linked with this version of PHP will first try to convert yout UTF-8-encoded PHP string into the local "ANSI" codepage selected in the running environment (see the CHCP command before starting PHP from a command line window) Your version of Windows is MOST PROBABLY NOT responsible of this weird thing. Actually, this is YOUR version of PHP which is not compiled correctly, and that uses the legacy ANSI version of the Win32 API (for compatibility with the legacy 16-bit versions of Windows 95/98 whose filesystem support in the kernel actually had no direct support for Unicode, but used an internal conversion layer to convert Unicode to the local ANSI codepage before using the actual ANSI version of the API). Recompile PHP using the compiler option to use the UNICODE version of the Win32 API (which should be the default today, and anyway always the default for PHP installed on a server that will NEVER be Windows 95 or Windows 98...) I can't confirm whether this is my problem or not. I used phpinfo() and did not find anything interesting, but I wasn't sure what to look for. I've been using XAMPP for easy installations, so I'm really not sure exactly how it was installed. I'm using Windows 7, 64 bit - so forgive my ignorance, but I'm not even sure if "Win32" is relevant here. How can I check if my current version of PHP was compiled with the configuration mentioned above? PHP Version: 5.3.8 System: Windows NT WES-PC 6.1 build 7601 (Windows 7 Home Premium Edition Service Pack 1) i586 Build Date: Aug 23 2011 11:47:20 Compiler: MSVC9 (Visual C++ 2008) Architecture: x86 Configure Command: cscript /nologo configure.js "--enable-snapshot-build" "--disable-isapi" "--enable-debug-pack" "--disable-isapi" "--without-mssql" "--without-pdo-mssql" "--without-pi3web" "--with-pdo-oci=D:\php-sdk\oracle\instantclient10\sdk,shared" "--with-oci8=D:\php-sdk\oracle\instantclient10\sdk,shared" "--with-oci8-11g=D:\php-sdk\oracle\instantclient11\sdk,shared" "--enable-object-out-dir=../obj/" "--enable-com-dotnet" "--with-mcrypt=static" "--disable-static-analyze"

    Read the article

  • Looking for advice on Hyper-v storage replication

    - by Notre1
    I am designing a 2-host Hyper-V R2 cluster with 6-10 guests stored on a SMB iSCSI SAN device (probably Promise VessRAID). I will be getting at least two of the SAN devices and need to eliminate the storage a single point of failure. Ideally, that would involve real-time failover for the storage, like the Windows failover clustering does for the hosts. This design will be used at around six of our sites, and I would like to allow for us to eventually setup a cluster at colocation site and replicate each site's VMs there for DR. (Ideally a live multi-site cluster, but a manual import of the VMs would be fine for this sort of DR.) The tools that come with enterprise SANs, like EMC and NetApp, seem to be the most commonly used items for a Hyper-V cluster, but I can't afford their prices with my budget. Outside of them, the two tools that seem to be most common for Hyper-V storage replication are SteelEye (now SIOS) DataKeeper Cluster Edition and Double-Take Availability. Originally, I was planning on using Clustered Shared Volume(s) (CSV), but it seems like replication support for these is either not available or brand new in both these products. It looks like CSVs are supported in Double-Take 5.22, see this discussion, but I don't think I want to run something that new in production. Right now, it seems like the best option for me is not to implement CSVs, implement some sort of storage replication, and upgrade to CSVs at a later date once replicating them is more mature. I would love to have live migration, and CSVs are not required for live migration if you are using one LUN per VM, so I guess this is what I'll do. I would prefer to stick to the using the Microsoft Windows Server and Hyper-V tools and features as much as possible. From that standpoint, SteelEye looks more appealing than Double-Take because they make the DataKeeper volume(s) available to the Failover Clustering Manager and then failover clustering is all configured and managed through the native Microsoft tools. Double-Take says that "clustered Hyper-V hosts are not supported," and Double-Take Availability itself seems to be what is used for the actual clustering and failover. Does anyone know if any of these replication tools work with more than two hosts in the cluster? All the information I can find on the web only uses two hosts in their examples. Are there any better tools than SteelEye and Double-Take for doing what I am trying to do, which is eliminate the storage as as single point of failure? Neverfail, AppAssure, and DataCore all seem to offer similar functionality, but they don't seems to be as popular as SteelEye and Double-Take. I have seen a number of people suggest using Starwind iSCSI SAN software for the shared storage, which includes replication (and CSV replication at that). There are a couple of reasons I have not seriously considered this route: 1) The company I work for is exclusively a Dell shop and Dell does not have any servers with that I can pack with more than six 3.5" SATA drives. 2) In the future, it could be advantegous for us to not be locked into a particular brand or type of storage and third-party replication softwares all allow replication to heterogeneous storage devices. I am pretty new to iSCSI and clustering, so please let me know if it looks like I am planning something that goes against best practices or overlooking/missing something.

    Read the article

  • MySQL reserves too much RAM

    - by Buddy
    I have a cheap VPS with 128Mb RAM and 256Mb burst. MySQL starts and reserves about 110Mb, but uses not more than 20Mb of them. My VPS Control Panel shows, that I use 127Mb (I also running nginx and sphinx), I know, that it shows reserved RAM, but when I reach over 128Mb, my VPS reboots automatically every 4 hours. So I want to force MySQL to reserve less RAM. How can i do that? I did some tweaks with my.conf but it helped not so much. top output: PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1 root 15 0 2156 668 572 S 0.0 0.3 0:00.03 init 11311 root 15 0 11212 356 228 S 0.0 0.1 0:00.00 vzctl 11312 root 18 0 3712 1484 1248 S 0.0 0.6 0:00.01 bash 11347 root 18 0 2284 916 732 R 0.0 0.3 0:00.00 top 13978 root 17 -4 2248 552 344 S 0.0 0.2 0:00.00 udevd 14262 root 15 0 1812 564 472 S 0.0 0.2 0:00.03 syslogd 14293 sphinx 15 0 11816 1172 672 S 0.0 0.4 0:00.07 searchd 14305 root 25 0 7192 1036 636 S 0.0 0.4 0:00.00 sshd 14321 root 25 0 2832 836 668 S 0.0 0.3 0:00.00 xinetd 15389 root 18 0 3708 1300 1132 S 0.0 0.5 0:00.00 mysqld_safe 15441 mysql 15 0 113m 16m 4440 S 0.0 6.4 0:00.15 mysqld 15489 root 21 0 13056 1456 340 S 0.0 0.6 0:00.00 nginx 15490 nginx 18 0 13328 2388 992 S 0.0 0.9 0:00.06 nginx 15507 nginx 25 0 19520 5888 4244 S 0.0 2.2 0:00.00 php-cgi 15508 nginx 18 0 19636 4876 2748 S 0.0 1.9 0:00.12 php-cgi 15509 nginx 15 0 19668 4872 2716 S 0.0 1.9 0:00.11 php-cgi 15518 root 18 0 4492 1116 568 S 0.0 0.4 0:00.01 crond MySQL tuner: >> MySQLTuner 1.0.1 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering Please enter your MySQL administrative login: root Please enter your MySQL administrative password: -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.0.77 [OK] Operating on 32-bit architecture with less than 2GB RAM -------- Storage Engine Statistics ------------------------------------------- [--] Status: -Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in InnoDB tables: 1M (Tables: 1) [OK] Total fragmented tables: 0 -------- Performance Metrics ------------------------------------------------- [--] Up for: 38m 43s (37 q [0.016 qps], 20 conn, TX: 4M, RX: 3K) [--] Reads / Writes: 100% / 0% [--] Total buffers: 28.1M global + 832.0K per thread (100 max threads) [OK] Maximum possible memory usage: 109.4M (42% of installed RAM) [OK] Slow queries: 0% (0/37) [OK] Highest usage of available connections: 1% (1/100) [OK] Key buffer size / total MyISAM indexes: 128.0K/64.0K [OK] Query cache efficiency: 42.1% (8 cached / 19 selects) [OK] Query cache prunes per day: 0 [!!] Temporary tables created on disk: 27% (3 on disk / 11 total) [!!] Thread cache is disabled [OK] Table cache hit rate: 57% (8 open / 14 opened) [OK] Open file limit used: 1% (12/1K) [OK] Table locks acquired immediately: 100% (22 immediate / 22 locks) [!!] Connections aborted: 10% [OK] InnoDB data size / buffer pool: 1.5M/8.0M -------- Recommendations ----------------------------------------------------- General recommendations: MySQL started within last 24 hours - recommendations may be inaccurate Enable the slow query log to troubleshoot bad queries When making adjustments, make tmp_table_size/max_heap_table_size equal Reduce your SELECT DISTINCT queries without LIMIT clauses Set thread_cache_size to 4 as a starting value Your applications are not closing MySQL connections properly Variables to adjust: tmp_table_size (> 32M) max_heap_table_size (> 16M) thread_cache_size (start at 4) I think if I do what MySQLtuner says, MySQL will use more RAM.

    Read the article

  • need assistance with my.cnf - 1500% CPU usage

    - by Alan Long
    I'm running into a few issues with our new database server. It is a HP G8 with 2 INTEL XEON E5-2650 processors and 32GB of ram. This server is dedicated as a MySQL server (5.1.69) for our intranet portal. I have been having issues with this server staying alive - I notice high CPU usage during certain times of day (8% ~ 1500%+) and see very low memory usage (7 ~ 15%) based on using the 'top' command. When the CPU usage passes 1000%, that is when the app usually dies. I'm trying to see what I'm doing wrong with the config file, hopefully one of the experts can chime in and let me know what they think. See below for my.cnf file: [mysqld] default-storage-engine=InnoDB datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock #user=mysql large-pages # Disabling symbolic-links is recommended to prevent assorted security risks symbolic-links=0 max_connections=275 tmp_table_size=1G key_buffer_size=384M key_buffer=384M thread_cache_size=1024 long_query_time=5 low_priority_updates=1 max_heap_table_size=1G myisam_sort_buffer_size=8M concurrent_insert=2 table_cache=1024 sort_buffer_size=8M read_buffer_size=5M read_rnd_buffer_size=6M join_buffer_size=16M table_definition_cache=6k open_files_limit=8k slow_query_log #skip-name-resolve # Innodb Settings innodb_buffer_pool_size=18G innodb_thread_concurrency=0 innodb_log_file_size=1G innodb_log_buffer_size=16M innodb_flush_log_at_trx_commit=2 innodb_lock_wait_timeout=50 innodb_file_per_table #innodb_buffer_pool_instances=4 #eliminating double buffering innodb_flush_method = O_DIRECT flush_time=86400 innodb_additional_mem_pool_size=40M #innodb_io_capacity = 5000 #innodb_read_io_threads = 64 #innodb_write_io_threads = 64 # increase until threads_created doesnt grow anymore thread_cache=1024 query_cache_type=1 query_cache_limit=4M query_cache_size=256M # Try number of CPU's*2 for thread_concurrency thread_concurrency = 0 wait_timeout = 1800 connect_timeout = 10 interactive_timeout = 60 [mysqldump] max_allowed_packet=32M [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid log-slow-queries=/var/log/mysql/slow-queries.log long_query_time = 1 log-queries-not-using-indexes we connect to one database with 75 tables, the largest table has 1,150,000 entries and the second largest has 128,036 entries. I have also verified that our PHP queries are optimized as best as possible. Reference - MySQLtuner: >> MySQLTuner 1.2.0 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.69-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: -Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in InnoDB tables: 420M (Tables: 75) [!!] Total fragmented tables: 75 -------- Security Recommendations ------------------------------------------- [!!] User '[email protected]' has no password set. -------- Performance Metrics ------------------------------------------------- [--] Up for: 1h 14m 50s (8M q [1K qps], 705 conn, TX: 6B, RX: 892M) [--] Reads / Writes: 68% / 32% [--] Total buffers: 19.7G global + 35.2M per thread (275 max threads) [!!] Maximum possible memory usage: 29.1G (93% of installed RAM) [OK] Slow queries: 0% (472/8M) [OK] Highest usage of available connections: 66% (183/275) [OK] Key buffer size / total MyISAM indexes: 384.0M/91.0K [OK] Key buffer hit rate: 100.0% (173 cached / 0 reads) [OK] Query cache efficiency: 96.2% (7M cached / 7M selects) [!!] Query cache prunes per day: 553614 [OK] Sorts requiring temporary tables: 0% (3 temp sorts / 1K sorts) [!!] Temporary tables created on disk: 49% (3K on disk / 7K total) [OK] Thread cache hit rate: 74% (183 created / 705 connections) [OK] Table cache hit rate: 97% (231 open / 238 opened) [OK] Open file limit used: 0% (17/8K) [OK] Table locks acquired immediately: 100% (432K immediate / 432K locks) [OK] InnoDB data size / buffer pool: 420.9M/18.0G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Reduce your overall MySQL memory footprint for system stability Increasing the query_cache size over 128M may reduce performance Temporary table size is already large - reduce result set size Reduce your SELECT DISTINCT queries without LIMIT clauses Variables to adjust: *** MySQL's maximum memory usage is dangerously high *** *** Add RAM before increasing MySQL buffer variables *** query_cache_size (> 256M) [see warning above] Thanks in advanced for your help!

    Read the article

  • mySQL Optimization Suggestions

    - by Brian Schroeter
    I'm trying to optimize our mySQL configuration for our large Magento website. The reason I believe that mySQL needs to be configured further is because New Relic has shown that our SELECT queries are taking a long time (20,000+ ms) in some categories. I ran MySQLTuner 1.3.0 and got the following results... (Disclaimer: I restarted mySQL earlier after tweaking some settings, and so the results here may not be 100% accurate): >> MySQLTuner 1.3.0 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering [OK] Currently running supported MySQL version 5.5.37-35.0 [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +ARCHIVE +BLACKHOLE +CSV -FEDERATED +InnoDB +MRG_MYISAM [--] Data in MyISAM tables: 7G (Tables: 332) [--] Data in InnoDB tables: 213G (Tables: 8714) [--] Data in PERFORMANCE_SCHEMA tables: 0B (Tables: 17) [--] Data in MEMORY tables: 0B (Tables: 353) [!!] Total fragmented tables: 5492 -------- Security Recommendations ------------------------------------------- [!!] User '@host5.server1.autopartsnetwork.com' has no password set. [!!] User '@localhost' has no password set. [!!] User 'root@%' has no password set. -------- Performance Metrics ------------------------------------------------- [--] Up for: 5h 3m 4s (5M q [317.443 qps], 42K conn, TX: 18B, RX: 2B) [--] Reads / Writes: 95% / 5% [--] Total buffers: 35.5G global + 184.5M per thread (1024 max threads) [!!] Maximum possible memory usage: 220.0G (174% of installed RAM) [OK] Slow queries: 0% (6K/5M) [OK] Highest usage of available connections: 5% (61/1024) [OK] Key buffer size / total MyISAM indexes: 512.0M/3.1G [OK] Key buffer hit rate: 100.0% (102M cached / 45K reads) [OK] Query cache efficiency: 66.9% (3M cached / 5M selects) [!!] Query cache prunes per day: 3486361 [OK] Sorts requiring temporary tables: 0% (0 temp sorts / 812K sorts) [!!] Joins performed without indexes: 1328 [OK] Temporary tables created on disk: 11% (126K on disk / 1M total) [OK] Thread cache hit rate: 99% (61 created / 42K connections) [!!] Table cache hit rate: 19% (9K open / 49K opened) [OK] Open file limit used: 2% (712/25K) [OK] Table locks acquired immediately: 100% (5M immediate / 5M locks) [!!] InnoDB buffer pool / data size: 32.0G/213.4G [OK] InnoDB log waits: 0 -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Reduce your overall MySQL memory footprint for system stability Enable the slow query log to troubleshoot bad queries Increasing the query_cache size over 128M may reduce performance Adjust your join queries to always utilize indexes Increase table_cache gradually to avoid file descriptor limits Read this before increasing table_cache over 64: http://bit.ly/1mi7c4C Variables to adjust: *** MySQL's maximum memory usage is dangerously high *** *** Add RAM before increasing MySQL buffer variables *** query_cache_size (> 512M) [see warning above] join_buffer_size (> 128.0M, or always use indexes with joins) table_cache (> 12288) innodb_buffer_pool_size (>= 213G) My my.cnf configuration is as follows... [client] port = 3306 [mysqld_safe] nice = 0 [mysqld] tmpdir = /var/lib/mysql/tmp user = mysql port = 3306 skip-external-locking character-set-server = utf8 collation-server = utf8_general_ci event_scheduler = 0 key_buffer = 512M max_allowed_packet = 64M thread_stack = 512K thread_cache_size = 512 sort_buffer_size = 24M read_buffer_size = 8M read_rnd_buffer_size = 24M join_buffer_size = 128M # for some nightly processes client sessions set the join buffer to 8 GB auto-increment-increment = 1 auto-increment-offset = 1 myisam-recover = BACKUP max_connections = 1024 # max connect errors artificially high to support behaviors of NetScaler monitors max_connect_errors = 999999 concurrent_insert = 2 connect_timeout = 5 wait_timeout = 180 net_read_timeout = 120 net_write_timeout = 120 back_log = 128 # this table_open_cache might be too low because of MySQL bugs #16244691 and #65384) table_open_cache = 12288 tmp_table_size = 512M max_heap_table_size = 512M bulk_insert_buffer_size = 512M open-files-limit = 8192 open-files = 1024 query_cache_type = 1 # large query limit supports SOAP and REST API integrations query_cache_limit = 4M # larger than 512 MB query cache size is problematic; this is typically ~60% full query_cache_size = 512M # set to true on read slaves read_only = false slow_query_log_file = /var/log/mysql/slow.log slow_query_log = 0 long_query_time = 0.2 expire_logs_days = 10 max_binlog_size = 1024M binlog_cache_size = 32K sync_binlog = 0 # SSD RAID10 technically has a write capacity of 10000 IOPS innodb_io_capacity = 400 innodb_file_per_table innodb_table_locks = true innodb_lock_wait_timeout = 30 # These servers have 80 CPU threads; match 1:1 innodb_thread_concurrency = 48 innodb_commit_concurrency = 2 innodb_support_xa = true innodb_buffer_pool_size = 32G innodb_file_per_table innodb_flush_log_at_trx_commit = 1 innodb_log_buffer_size = 2G skip-federated [mysqldump] quick quote-names single-transaction max_allowed_packet = 64M I have a monster of a server here to power our site because our catalog is very large (300,000 simple SKUs), and I'm just wondering if I'm missing anything that I can configure further. :-) Thanks!

    Read the article

  • What networking hardware do I need in this situation (Fairpoint [ISP] "E-DIA" connection)?

    - by Tegeril
    Right away you'd probably want to say, "Well just ask Fairpoint." I've done that, a number of times in as many different ways I can phrase it and just keep hitting a brick wall where they will not commit to giving any useful information and instead recommend contracting an outside firm and spending a pile of money. Anyway... I'm trying to help a family member out with an office connection that is being setup. I've managed to scrape tiny details here and there from our discussions with the ISP (Fairpoint in Maine) about what is going to be done and what is going to be needed. This is the connection that is being setup: http://www.fairpoint.com/enterprise/vantagepoint/e-dia/index.jsp Information I have been given: Via this connection I can get IPs across different C blocks if that were necessary (it is not) Fairpoint is bringing hardware with them that they claim simply does the conversion from whatever line is coming in the building to ethernet, they have referred to this as the "Fairpoint Netvanta" which I know suggests a line of products that I have looked up, but some (most? all?) of those seems to handle all the routing that I saw. Fairpoint says that I need to bring my own router to sit behind their device. They have literally declined to even suggest products that have worked for other clients in the past and fall back on "any business router works, not a home router." That alone makes my head spin. Detail and clarity hit a brick wall from there. At one moment I got them to cough up that the router I provide needs to be able to do VPN tunneling but they typically fall back to "not a home router" and I was even given "just a business router, Cisco or something, it'll be $500-$1000". Now I know that VPN tunneling routers exist well below that price point and since this connection is going to one machine, possibly two only via ethernet, my desire to purchase networking hardware that over-delivers what I need is not very high. They are literally setting all this up, have provided no configuration details for after they finish, and expect me to just plunk a $500+ router behind it and cross my fingers or contract out to a third party company. If there were other options available for the location, I would have dropped them in a second, but there aren't. The device that is connected requires a static IP and I'm honestly a bit hazy on the necessity of an additional router behind their device and generally a bit over my head. I presume that the router needs to be able to serve external static IPs to its clients, but I really don't know what is going to show up when they come to do the install. This was originally going to be run via an ADSL bridge modem with a range of static IPs (which is easy and is currently setup properly) but the location is too far from the telco to get speeds that we really want for upload and this is also a connection that needs high availability. Any suggestions would be greatly appreciated (I see a number of options in the Cisco Small Business line and other competitors that aren't going to break the bank…), especially if you've worked with Fairpoint before! Thanks for reading my wall of text.

    Read the article

  • Compiling program that uses libpcap on Mac OSX using iPhone 3.1.1 SDK for use on iPhone

    - by Alan
    Hey SOV users, I have a question that I'm hoping some iPhone Developers may be able to help with. I had a look at statically compiling a binary on my Mac and moving it over to the iPhone for execution. I have managed to get this bit of it working by installing the iPhone 3.1.3 SDK on my Mac and setting the architecture to the iPhone in the gcc line as follows; /Developer/Platforms/iPhoneOS.platform/Developer/usr/bin/gcc -I ~/Downloads/libpcap-1.1.1/pcap-compiled/ -arch armv6 -isysroot /Developer/Platforms/iPhoneOS.platform/Developer/SDKs/iPhoneOS2.1.sdk -o test test.c I have managed to successfully compile a "Hello World" C program and executed it on the iPhone with success. e.g. include int main() { printf("Hello, World!\n"); return(0); } This worked a charm. I am also using 'ldid' to sign the application (but only if necessary). Anyways, I have been trying to get a program to compile which uses libpcap (http://www.tcpdump.org/) but with little success. I have downloaded and installed libpcap-1.1.1 on my mac and set the configure --prefix to /Developer/Platforms/iPhoneOS.platform/Developer/SDKs/iPhoneOS2.1.sdk/usr/local and build the application. I then saw that the includes actually reside in Developer/Platforms/iPhoneOS.platform/Developer/SDKs/iPhoneOS2.1.sdk/usr/includes and so moved the Developer/Platforms/iPhoneOS.platform/Developer/SDKs/iPhoneOS2.1.sdk/usr/local/include files (which contained only the pcap stuff) to the correct location. I then attempted to compile the test program using; /Developer/Platforms/iPhoneOS.platform/Developer/usr/bin/gcc -I /Developer/Platforms/iPhoneOS.platform/Developer/SDKs/iPhoneOS3.1.3.sdk/usr/include/ -arch armv6 -isysroot /Developer/Platforms/iPhoneOS.platform/Developer/SDKs/iPhoneOS2.1.sdk -o pcap pcap.c -lpcap This worked a lot better than other tests but produces an error; i.e. ld: library not found for -lcrt1.o collect2: ld returned 1 exit status Do you have any ideas as to how I can do this successfully? I've tried a load of different things but none seem to be successful. Basically, I just want to install (or add) some headers to the existing iPhoneOS SDK for use in compiling programs. Any ideas? Cheers, A

    Read the article

  • JBoss 6 deployment of message-driven bean error

    - by AntonioP
    Hello, I have an java EE application which has one message-driven bean and it runs fine on JBoss 4, however when I configure the project for JBoss 6 and deploy on it, I get this error; WARN [org.jboss.ejb.deployers.EjbDeployer.verifier] EJB spec violation: ... The message driven bean must declare one onMessage() method. ... org.jboss.deployers.spi.DeploymentException: Verification of Enterprise Beans failed, see above for error messages. But my bean HAS the onMessage method! It would not have worked on jboss 4 either then. Why do I get this error!? Edit: The class in question looks like this package ... imports ... public class MyMDB implements MessageDrivenBean, MessageListener { AnotherSessionBean a; OneMoreSessionBean b; public MyMDB() {} public void onMessage(Message message) { if (message instanceof TextMessage) { try { //Lookup sessionBeans by jndi, create them lookupABean(); // check message-type, then invokie a.handle(message); // else b.handle(message); } catch (SomeException e) { //handling it } } } public void lookupABean() { try { // code to lookup session beans and create. } catch (CreateException e) { // handling it and catching NamingException too } } } Edit 2: And this is the jboss.xml relevant parts <message-driven> <ejb-name>MyMDB</ejb-name> <destination-jndi-name>topic/A_Topic</destination-jndi-name> <local-jndi-name>A_Topic</local-jndi-name> <mdb-user>user</mdb-user> <mdb-passwd>pass</mdb-passwd> <mdb-client-id>MyMessageBean</mdb-client-id> <mdb-subscription-id>subid</mdb-subscription-id> <resource-ref> <res-ref-name>jms/TopicFactory</res-ref-name> <jndi-name>jms/TopicFactory</jndi-name> </resource-ref> </message-driven>

    Read the article

  • Best ASP.NET E-Commerce Framework (aspDotNetStoreFront, AbleCommerce, BVCommerce, MediaChase,...)

    - by EfficionDave
    I need a full-featured asp.net E-Commerce solution for a project. It needs to be easily extensible as I need to extend it to integrate with a custom Flash based personalization engine. It should also have a great administrative back-end that handles inventory tracking, report, labels, shipping, ... so that the client can really use it as the basis for their business. I've used quite a few different E-Commerce systems including OSCommerce, Zen Cart, Catalook, and eTailer. While I was impressed with Zen Cart and eTailer, this project is big enough that I want to try a more serious, commercial offering. I'm particularly interested in thoughts on aspdotnetstorefront, BVCommerce, AbleCommerce, and MediaChase. [UPDATE] I've done quite a bit of evaluation since I posted this question and will give some of my findings below: BVCommerce - The price point is nice, the product seems fairly well regarded, and I've heard good things about customizing/extending it, it just doesn't seem like it's going to meet my needs as an Top Tier ECommerce solution. After viewing the tutorial videos, the Admin interface just seems too basic and outdated. aspDotNetStorefront - The integration with DotNetNuke was it's biggest selling point for me but after reading peoples opinions, it's integration seems quite weak. It's sounds like there's a significant learning curve and the architecture just doesn't sound like it's as clean as it should be. AbleCommerce - After a rather thorough evaluation, I have selected AbleCommerce for at least my next project. The Admin interface is beautiful and has a nice list of features. The E-Commerce portion of the user side is very well done, highly skin-able (using Master Pages and a couple other techniques), and the checkout workflow has all the features I need while still being very clean. Source to the API can be bought for $500 but you generally won't need it. There are some 3rd party modules available but there's not currently a large market for these. The biggest glaring weakness of AbleCommerce I've found is their CMS capabilities are very limited and not at all well suited for a non-technical user to make most site content updates. But I have a good solution for that that I plan adapting into AbleCommerce. They will automatically generate a site for you to play with to your heart's content for 30 days. It is defniitely worth checking out.

    Read the article

  • Qt vs .NET - plz no n00bs who don't know wtf they're talking about [closed]

    - by Pirate for Profit
    Man in all these Qt vs. .NET discussions 90% these people don't know WTF they're talking about. Trying to get a real comparison chart going before we embark on a major fucking project. And yes I'm drunk, and yes I use cocaine. Event Handling In Qt the event handling system you just emit signals when something cool happens and then catch them in slots, for instance emit valueChanged(int percent, bool something); and void MyCatcherObj::valueChanged(int p, bool ok){} blocking them and disconnecting them when needed, doing it across threads... once you get the hang of it, it just seems a lot more natural and intuitive than the way the .NET event handling is set up (you know, object sender, CustomEventArgs e). And I'm not just talking about syntax, because in the end the .NET delegate crap is the bomb. I'm also talking about in more than just reflection (because, yes, .NET obviously has much stronger reflection capabilities). I'm talking about in the way the system feels to a human being. Qt wins hands down i m o. Basically, the footprints make more sense and you can visualize the project easier without the clunky event handling system. I wish I could it explain it better. The only thing is, I do love some of the ease of C# compared to C++ and .NET's assembly architecture. That is a big bonus for modular projects, which are a PITA to do in C++. Database Ease of Doing Crap Also what about datasets and database manipulations. I think .net wins here but I'm not sure. Threading/Conccurency How do you guys think of the threading? In .NET, all I've ever done is make like a list of master worker threads with locks. I like QConcurrentFramework, you don't worry about locks or anything, and with the ease of the signal slot system across threads it's nice to get notified about the progress of things. Memory Usage Also what do you think of the overall memory usage comparison. Is the .NET garbage collector pretty on the ball and quick compared to the instantaneous nature of native memory management? Or does it just let programs leak up a storm and lag the computer then clean it up when it's about to really lag? However, I am a n00b who doesn't know what I'm talking about, please school me on the subject.

    Read the article

< Previous Page | 373 374 375 376 377 378 379 380 381 382 383 384  | Next Page >