rails routing - Page 379

Inbound SIP calls through Cisco 881 NAT hang up after a few seconds

- by MasterRoot24

I've recently moved to a Cisco 881 router for my WAN link. I was previously using a Cisco Linksys WAG320N as my modem/router/WiFi AP/NAT firewall. The WAG320N is now running in bridged mode, so it's simply acting as a modem with one of it's LAN ports connected to FE4 WAN on my Cisco 881. The Cisco 881 get's a DHCP provided IP from my ISP. My LAN is part of default Vlan 1 (192.168.1.0/24). General internet connectivity is working great, I've managed to setup static NAT rules for my HTTP/HTTPS/SMTP/etc. services which are running on my LAN. I don't know whether it's worth mentioning that I've opted to use NVI NAT (ip nat enable as opposed to the traditional ip nat outside/ip nat inside) setup. My reason for this is that NVI allows NAT loopback from my LAN to the WAN IP and back in to the necessary server on the LAN. I run an Asterisk 1.8 PBX on my LAN, which connects to a SIP provider on the internet. Both inbound and outbound calls through the old setup (WAG320N providing routing/NAT) worked fine. However, since moving to the Cisco 881, inbound calls drop after around 10 seconds, whereas outbound calls work fine. The following message is logged on my Asterisk PBX: [Dec 9 15:27:45] WARNING[27734]: chan_sip.c:3641 retrans_pkt: Retransmission timeout reached on transmission [email protected] for seqno 1 (Critical Response) -- See https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions Packet timed out after 6528ms with no response [Dec 9 15:27:45] WARNING[27734]: chan_sip.c:3670 retrans_pkt: Hanging up call [email protected] - no reply to our critical packet (see https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions). (I know that this is quite a common issue - I've spend the best part of 2 days solid on this, trawling Google.) I've done as I am told and checked https://wiki.asterisk.org/wiki/display/AST/SIP+Retransmissions. Referring to the section "Other SIP requests" in the page linked above, I believe that the hangup to be caused by the ACK from my SIP provider not being passed back through NAT to Asterisk on my PBX. I tried to ascertain this by dumping the packets on my WAN interface on the 881. I managed to obtain a PCAP dump of packets in/out of my WAN interface. Here's an example of an ACK being reveived by the router from my provider: 689 21.219999 193.x.x.x 188.x.x.x SIP 502 Request: ACK sip:[email protected] | However a SIP trace on the Asterisk server show's that there are no ACK's received in response to the 200 OK from my PBX: http://pastebin.com/wwHpLPPz In the past, I have been strongly advised to disable any sort of SIP ALGs on routers and/or firewalls and the many posts regarding this issue on the internet seem to support this. However, I believe on Cisco IOS, the config command to disable SIP ALG is no ip nat service sip udp port 5060 however, this doesn't appear to help the situation. To confirm that config setting is set: Router1#show running-config | include sip no ip nat service sip udp port 5060 Another interesting twist: for a short period of time, I tried another provider. Luckily, my trial account with them is still available, so I reverted my Asterisk config back to the revision before I integrated with my current provider. I then dialled in to the DDI associated with the trial trunk and the call didn't get hung up and I didn't get the error above! To me, this points at the provider, however I know, like all providers do, will say "There's no issues with our SIP proxies - it's your firewall." I'm tempted to agree with this, as this issue was not apparent with the old WAG320N router when it was doing the NAT'ing. I'm sure you'll want to see my running-config too: ! ! Last configuration change at 15:55:07 UTC Sun Dec 9 2012 by xxx version 15.2 no service pad service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec localtime show-timezone service timestamps log datetime msec localtime show-timezone no service password-encryption service sequence-numbers ! hostname Router1 ! boot-start-marker boot-end-marker ! ! security authentication failure rate 10 log security passwords min-length 6 logging buffered 4096 logging console critical enable secret 4 xxx ! aaa new-model ! ! aaa authentication login local_auth local ! ! ! ! ! aaa session-id common ! memory-size iomem 10 ! crypto pki trustpoint TP-self-signed-xxx enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-xxx revocation-check none rsakeypair TP-self-signed-xxx ! ! crypto pki certificate chain TP-self-signed-xxx certificate self-signed 01 quit no ip source-route no ip gratuitous-arps ip auth-proxy max-login-attempts 5 ip admission max-login-attempts 5 ! ! ! ! ! no ip bootp server ip domain name dmz.merlin.local ip domain list dmz.merlin.local ip domain list merlin.local ip name-server x.x.x.x ip inspect audit-trail ip inspect udp idle-time 1800 ip inspect dns-timeout 7 ip inspect tcp idle-time 14400 ip inspect name autosec_inspect ftp timeout 3600 ip inspect name autosec_inspect http timeout 3600 ip inspect name autosec_inspect rcmd timeout 3600 ip inspect name autosec_inspect realaudio timeout 3600 ip inspect name autosec_inspect smtp timeout 3600 ip inspect name autosec_inspect tftp timeout 30 ip inspect name autosec_inspect udp timeout 15 ip inspect name autosec_inspect tcp timeout 3600 ip cef login block-for 3 attempts 3 within 3 no ipv6 cef ! ! multilink bundle-name authenticated license udi pid CISCO881-SEC-K9 sn ! ! username xxx privilege 15 secret 4 xxx username xxx secret 4 xxx ! ! ! ! ! ip ssh time-out 60 ! ! ! ! ! ! ! ! ! interface FastEthernet0 no ip address ! interface FastEthernet1 no ip address ! interface FastEthernet2 no ip address ! interface FastEthernet3 switchport access vlan 2 no ip address ! interface FastEthernet4 ip address dhcp no ip redirects no ip unreachables no ip proxy-arp ip nat enable duplex auto speed auto ! interface Vlan1 ip address 192.168.1.1 255.255.255.0 no ip redirects no ip unreachables no ip proxy-arp ip nat enable ! interface Vlan2 ip address 192.168.0.2 255.255.255.0 ! ip forward-protocol nd ip http server ip http access-class 1 ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ! ! no ip nat service sip udp port 5060 ip nat source list 1 interface FastEthernet4 overload ip nat source static tcp x.x.x.x 80 interface FastEthernet4 80 ip nat source static tcp x.x.x.x 443 interface FastEthernet4 443 ip nat source static tcp x.x.x.x 25 interface FastEthernet4 25 ip nat source static tcp x.x.x.x 587 interface FastEthernet4 587 ip nat source static tcp x.x.x.x 143 interface FastEthernet4 143 ip nat source static tcp x.x.x.x 993 interface FastEthernet4 993 ip nat source static tcp x.x.x.x 1723 interface FastEthernet4 1723 ! ! logging trap debugging logging facility local2 access-list 1 permit 192.168.1.0 0.0.0.255 access-list 1 permit 192.168.0.0 0.0.0.255 no cdp run ! ! ! ! control-plane ! ! banner motd Authorized Access only ! line con 0 login authentication local_auth length 0 transport output all line aux 0 exec-timeout 15 0 login authentication local_auth transport output all line vty 0 1 access-class 1 in logging synchronous login authentication local_auth length 0 transport preferred none transport input telnet transport output all line vty 2 4 access-class 1 in login authentication local_auth length 0 transport input ssh transport output all ! ! end ...and, if it's of any use, here's my Asterisk SIP config: [general] context=default ; Default context for calls allowoverlap=no ; Disable overlap dialing support. (Default is yes) udpbindaddr=0.0.0.0 ; IP address to bind UDP listen socket to (0.0.0.0 binds to all) ; Optionally add a port number, 192.168.1.1:5062 (default is port 5060) tcpenable=no ; Enable server for incoming TCP connections (default is no) tcpbindaddr=0.0.0.0 ; IP address for TCP server to bind to (0.0.0.0 binds to all interfaces) ; Optionally add a port number, 192.168.1.1:5062 (default is port 5060) srvlookup=yes ; Enable DNS SRV lookups on outbound calls ; Note: Asterisk only uses the first host ; in SRV records ; Disabling DNS SRV lookups disables the ; ability to place SIP calls based on domain ; names to some other SIP users on the Internet ; Specifying a port in a SIP peer definition or ; when dialing outbound calls will supress SRV ; lookups for that peer or call. directmedia=no ; Don't allow direct RTP media between extensions (doesn't work through NAT) externhost=<MY DYNDNS HOSTNAME> ; Our external hostname to resolve to IP and be used in NAT'ed packets localnet=192.168.1.0/24 ; Define our local network so we know which packets need NAT'ing qualify=yes ; Qualify peers by default dtmfmode=rfc2833 ; Set the default DTMF mode disallow=all ; Disallow all codecs by default allow=ulaw ; Allow G.711 u-law allow=alaw ; Allow G.711 a-law ; ---------------------- ; SIP Trunk Registration ; ---------------------- ; Orbtalk register => <MY SIP PROVIDER USER NAME>:[email protected]/<MY DDI> ; Main Orbtalk number ; ---------- ; Trunks ; ---------- [orbtalk] ; Main Orbtalk trunk type=peer insecure=invite host=sipgw3.orbtalk.co.uk nat=yes username=<MY SIP PROVIDER USER NAME> defaultuser=<MY SIP PROVIDER USER NAME> fromuser=<MY SIP PROVIDER USER NAME> secret=xxx context=inbound I really don't know where to go with this. If anyone can help me find out why these calls are being dropped off, I'd be grateful if you could chime in! Please let me know if any further info is required.

Read the article

Async ignored on AJAX requests on Nginx server

- by eComEvo

Despite sending an async request to the server over AJAX, the server will not respond until the previous unrelated request has finished. The following code is only broken in this way on Nginx, but runs perfectly on Apache. This call will start a background process and it waits for it to complete so it can display the final result. $.ajax({ type: 'GET', async: true, url: $(this).data('route'), data: $('input[name=data]').val(), dataType: 'json', success: function (data) { /* do stuff */} error: function (data) { /* handle errors */} }); The below is called after the above, which on Apache requires 100ms to execute and repeats itself, showing progress for data being written in the background: checkStatusInterval = setInterval(function () { $.ajax({ type: 'GET', async: false, cache: false, url: '/process-status?process=' + currentElement.attr('id'), dataType: 'json', success: function (data) { /* update progress bar and status message */ } }); }, 1000); Unfortunately, when this script is run from nginx, the above progress request never even finishes a single request until the first AJAX request that sent the data is done. If I change the async to TRUE in the above, it executes one every interval, but none of them complete until that very first AJAX request finishes. Here is the main nginx conf file: #user nobody; worker_processes 1; #error_log logs/error.log; #error_log logs/error.log notice; #error_log logs/error.log info; #pid logs/nginx.pid; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; server_names_hash_bucket_size 64; # configure temporary paths # nginx is started with param -p, setting nginx path to serverpack installdir fastcgi_temp_path temp/fastcgi; uwsgi_temp_path temp/uwsgi; scgi_temp_path temp/scgi; client_body_temp_path temp/client-body 1 2; proxy_temp_path temp/proxy; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; #access_log logs/access.log main; # Sendfile copies data between one FD and other from within the kernel. # More efficient than read() + write(), since the requires transferring data to and from the user space. sendfile on; # Tcp_nopush causes nginx to attempt to send its HTTP response head in one packet, # instead of using partial frames. This is useful for prepending headers before calling sendfile, # or for throughput optimization. tcp_nopush on; # don't buffer data-sends (disable Nagle algorithm). Good for sending frequent small bursts of data in real time. tcp_nodelay on; types_hash_max_size 2048; # Timeout for keep-alive connections. Server will close connections after this time. keepalive_timeout 90; # Number of requests a client can make over the keep-alive connection. This is set high for testing. keepalive_requests 100000; # allow the server to close the connection after a client stops responding. Frees up socket-associated memory. reset_timedout_connection on; # send the client a "request timed out" if the body is not loaded by this time. Default 60. client_header_timeout 20; client_body_timeout 60; # If the client stops reading data, free up the stale client connection after this much time. Default 60. send_timeout 60; # Size Limits client_body_buffer_size 64k; client_header_buffer_size 4k; client_max_body_size 8M; # FastCGI fastcgi_connect_timeout 60; fastcgi_send_timeout 120; fastcgi_read_timeout 300; # default: 60 secs; when step debugging with XDEBUG, you need to increase this value fastcgi_buffer_size 64k; fastcgi_buffers 4 64k; fastcgi_busy_buffers_size 128k; fastcgi_temp_file_write_size 128k; # Caches information about open FDs, freqently accessed files. open_file_cache max=200000 inactive=20s; open_file_cache_valid 30s; open_file_cache_min_uses 2; open_file_cache_errors on; # Turn on gzip output compression to save bandwidth. # http://wiki.nginx.org/HttpGzipModule gzip on; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; gzip_http_version 1.1; gzip_vary on; gzip_proxied any; #gzip_proxied expired no-cache no-store private auth; gzip_comp_level 6; gzip_buffers 16 8k; gzip_types text/plain text/css application/json application/x-javascript text/xml application/xml application/xml+rss text/javascript application/javascript; # show all files and folders autoindex on; server { # access from localhost only listen 127.0.0.1:80; server_name localhost; root www; # the following default "catch-all" configuration, allows access to the server from outside. # please ensure your firewall allows access to tcp/port 80. check your "skype" config. # listen 80; # server_name _; log_not_found off; charset utf-8; access_log logs/access.log main; # handle files in the root path /www location / { index index.php index.html index.htm; } #error_page 404 /404.html; # redirect server error pages to the static page /50x.html # error_page 500 502 503 504 /50x.html; location = /50x.html { root www; } # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9100 # location ~ \.php$ { try_files $uri =404; fastcgi_pass 127.0.0.1:9100; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; } # add expire headers location ~* ^.+.(gif|ico|jpg|jpeg|png|flv|swf|pdf|mp3|mp4|xml|txt|js|css)$ { expires 30d; } # deny access to .htaccess files (if Apache's document root concurs with nginx's one) # deny access to git & svn repositories location ~ /(\.ht|\.git|\.svn) { deny all; } } # include config files of "enabled" domains include domains-enabled/*.conf; } Here is the enabled domain conf file: access_log off; access_log C:/server/www/test.dev/logs/access.log; error_log C:/server/www/test.dev/logs/error.log; # HTTP Server server { listen 127.0.0.1:80; server_name test.dev; root C:/server/www/test.dev/public; index index.php; rewrite_log on; default_type application/octet-stream; #include /etc/nginx/mime.types; # Include common configurations. include domains-common/location.conf; } # HTTPS server server { listen 443 ssl; server_name test.dev; root C:/server/www/test.dev/public; index index.php; rewrite_log on; default_type application/octet-stream; #include /etc/nginx/mime.types; # Include common configurations. include domains-common/location.conf; include domains-common/ssl.conf; } Contents of ssl.conf: # OpenSSL for HTTPS connections. ssl on; ssl_certificate C:/server/bin/openssl/certs/cert.pem; ssl_certificate_key C:/server/bin/openssl/certs/cert.key; ssl_session_timeout 5m; ssl_protocols SSLv3 TLSv1 TLSv1.1 TLSv1.2; ssl_ciphers HIGH:!aNULL:!MD5; ssl_prefer_server_ciphers on; # Pass the PHP scripts to FastCGI server listening on 127.0.0.1:9100 location ~ \.php$ { try_files $uri =404; fastcgi_param HTTPS on; fastcgi_pass 127.0.0.1:9100; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; } Contents of location.conf: # Remove trailing slash to please Laravel routing system. if (!-d $request_filename) { rewrite ^/(.+)/$ /$1 permanent; } location / { try_files $uri $uri/ /index.php?$query_string; } # We don't need .ht files with nginx. location ~ /(\.ht|\.git|\.svn) { deny all; } # Added cache headers for images. location ~* \.(png|jpg|jpeg|gif)$ { expires 30d; log_not_found off; } # Only 3 hours on CSS/JS to allow me to roll out fixes during early weeks. location ~* \.(js|css)$ { expires 3h; log_not_found off; } # Add expire headers. location ~* ^.+.(gif|ico|jpg|jpeg|png|flv|swf|pdf|mp3|mp4|xml|txt)$ { expires 30d; } # Pass the PHP scripts to FastCGI server listening on 127.0.0.1:9100 location ~ \.php$ { try_files $uri /index.php =404; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; fastcgi_pass 127.0.0.1:9100; } Any ideas where this is going wrong?

Read the article

Something very strange with network

- by Rodnower

Hello, I have Windows 7 and I have very strange thing with my network. Some time I was connected through wireless router and my IP was 192.168.2.103, router's IP was 192.168.2.1 and some other IP was 192.168.2.100. The last I get from page "active DHCP clients" of web interface of the router and from "wireless clients" I may to see that 192.168.2.100 not (!) belong to my MAC address. Router build by EDimax. So after that I disabled wireless function of the router and restarted it. In this time I had not ping to 192.168.2.1. Also I had not any other connection, not wireless nor cable, but (!) I still had ping to 192.168.2.100 and I not understand what this voodoo is... C:\Users\Andrey>ping 192.168.2.100 Pinging 192.168.2.100 with 32 bytes of data: Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Ping statistics for 192.168.2.100: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms This is what I had: C:\Users\Andrey>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : Andrey-PC Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Wireless LAN adapter Wireless Network Connection 3: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Virtual WiFi Miniport Adapter #2 Physical Address. . . . . . . . . : 06-1D-7D-40-61-EB DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Wireless LAN adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Gigabyte GN-WS50G (mini) PCI-E WLAN Card Physical Address. . . . . . . . . : 00-1D-7D-40-61-EB DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Controller Physical Address. . . . . . . . . : 00-1B-24-B6-09-91 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes C:\Users\Andrey>arp -a -v Interface: 127.0.0.1 --- 0x1 Internet Address Physical Address Type 224.0.0.22 static 239.255.255.250 static Interface: 0.0.0.0 --- 0xffffffff Internet Address Physical Address Type 192.168.2.1 00-0e-2e-d2-8c-af invalid 192.168.2.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Interface: 0.0.0.0 --- 0xffffffff Internet Address Physical Address Type 192.168.2.1 00-0e-2e-ff-f1-f6 dynamic 192.168.2.101 00-27-19-bc-8b-9c dynamic 192.168.2.102 00-16-e6-6c-ae-d4 dynamic 192.168.2.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Interface: 0.0.0.0 --- 0xffffffff Internet Address Physical Address Type 224.0.0.22 01-00-5e-00-00-16 static 255.255.255.255 ff-ff-ff-ff-ff-ff static C:\Users\Andrey>route print =========================================================================== Interface List 14...06 1d 7d 40 61 eb ......Microsoft Virtual WiFi Miniport Adapter #2 13...00 1d 7d 40 61 eb ......Gigabyte GN-WS50G (mini) PCI-E WLAN Card 11...00 1b 24 b6 09 91 ......Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Controller 1...........................Software Loopback Interface 1 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 1 306 ff00::/8 On-link =========================================================================== Persistent Routes: None Only after reboot I lost ping to there: C:\Users\Andrey>ping 192.168.2.100 Pinging 192.168.2.100 with 32 bytes of data: PING: transmit failed. General failure. PING: transmit failed. General failure. PING: transmit failed. General failure. PING: transmit failed. General failure. Ping statistics for 192.168.2.100: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), So what this mysterious cache is? Thank you for ahead.

Read the article

OpenVPN Client timing out

- by Austin

I recently installed OpenVPN on my Ubuntu VPS. Whenenver I try to connect to it, I can establish a connection just fine. However, everything I try to connect to times out. If I try to ping something, it will resolve the IP, but will time out after resolving the IP. (So DNS Server seems to be working correctly) My server.conf has this relevant information (At least I think it's relevant. I'm not sure if you need more or not) # Which local IP address should OpenVPN # listen on? (optional) ;local a.b.c.d # Which TCP/UDP port should OpenVPN listen on? # If you want to run multiple OpenVPN instances # on the same machine, use a different port # number for each one. You will need to # open up this port on your firewall. port 1194 # TCP or UDP server? ;proto tcp proto udp # "dev tun" will create a routed IP tunnel, # "dev tap" will create an ethernet tunnel. # Use "dev tap0" if you are ethernet bridging # and have precreated a tap0 virtual interface # and bridged it with your ethernet interface. # If you want to control access policies # over the VPN, you must create firewall # rules for the the TUN/TAP interface. # On non-Windows systems, you can give # an explicit unit number, such as tun0. # On Windows, use "dev-node" for this. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. ;dev tap dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel if you # have more than one. On XP SP2 or higher, # you may need to selectively disable the # Windows firewall for the TAP adapter. # Non-Windows systems usually don't need this. ;dev-node MyTap # SSL/TLS root certificate (ca), certificate # (cert), and private key (key). Each client # and the server must have their own cert and # key file. The server and all clients will # use the same ca file. # # See the "easy-rsa" directory for a series # of scripts for generating RSA certificates # and private keys. Remember to use # a unique Common Name for the server # and each of the client certificates. # # Any X509 key management system can be used. # OpenVPN can also use a PKCS #12 formatted key file # (see "pkcs12" directive in man page). ca ca.crt cert server.crt key server.key # This file should be kept secret # Diffie hellman parameters. # Generate your own with: # openssl dhparam -out dh1024.pem 1024 # Substitute 2048 for 1024 if you are using # 2048 bit keys. dh dh1024.pem # Configure server mode and supply a VPN subnet # for OpenVPN to draw client addresses from. # The server will take 10.8.0.1 for itself, # the rest will be made available to clients. # Each client will be able to reach the server # on 10.8.0.1. Comment this line out if you are # ethernet bridging. See the man page for more info. server 10.8.0.0 255.255.255.0 # Maintain a record of client <-> virtual IP address # associations in this file. If OpenVPN goes down or # is restarted, reconnecting clients can be assigned # the same virtual IP address from the pool that was # previously assigned. ifconfig-pool-persist ipp.txt # Configure server mode for ethernet bridging. # You must first use your OS's bridging capability # to bridge the TAP interface with the ethernet # NIC interface. Then you must manually set the # IP/netmask on the bridge interface, here we # assume 10.8.0.4/255.255.255.0. Finally we # must set aside an IP range in this subnet # (start=10.8.0.50 end=10.8.0.100) to allocate # to connecting clients. Leave this line commented # out unless you are ethernet bridging. ;server-bridge 10.8.0.4 255.255.255.0 10.8.0.50 10.8.0.100 # Configure server mode for ethernet bridging # using a DHCP-proxy, where clients talk # to the OpenVPN server-side DHCP server # to receive their IP address allocation # and DNS server addresses. You must first use # your OS's bridging capability to bridge the TAP # interface with the ethernet NIC interface. # Note: this mode only works on clients (such as # Windows), where the client-side TAP adapter is # bound to a DHCP client. ;server-bridge # Push routes to the client to allow it # to reach other private subnets behind # the server. Remember that these # private subnets will also need # to know to route the OpenVPN client # address pool (10.8.0.0/255.255.255.0) # back to the OpenVPN server. ;push "route 192.168.10.0 255.255.255.0" ;push "route 192.168.20.0 255.255.255.0" # To assign specific IP addresses to specific # clients or if a connecting client has a private # subnet behind it that should also have VPN access, # use the subdirectory "ccd" for client-specific # configuration files (see man page for more info). # EXAMPLE: Suppose the client # having the certificate common name "Thelonious" # also has a small subnet behind his connecting # machine, such as 192.168.40.128/255.255.255.248. # First, uncomment out these lines: ;client-config-dir ccd ;route 192.168.40.128 255.255.255.248 # Then create a file ccd/Thelonious with this line: # iroute 192.168.40.128 255.255.255.248 # This will allow Thelonious' private subnet to # access the VPN. This example will only work # if you are routing, not bridging, i.e. you are # using "dev tun" and "server" directives. # EXAMPLE: Suppose you want to give # Thelonious a fixed VPN IP address of 10.9.0.1. # First uncomment out these lines: ;client-config-dir ccd ;route 10.9.0.0 255.255.255.252 # Then add this line to ccd/Thelonious: # ifconfig-push 10.9.0.1 10.9.0.2 # Suppose that you want to enable different # firewall access policies for different groups # of clients. There are two methods: # (1) Run multiple OpenVPN daemons, one for each # group, and firewall the TUN/TAP interface # for each group/daemon appropriately. # (2) (Advanced) Create a script to dynamically # modify the firewall in response to access # from different clients. See man # page for more info on learn-address script. ;learn-address ./script # If enabled, this directive will configure # all clients to redirect their default # network gateway through the VPN, causing # all IP traffic such as web browsing and # and DNS lookups to go through the VPN # (The OpenVPN server machine may need to NAT # or bridge the TUN/TAP interface to the internet # in order for this to work properly). push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 8.8.8.8" # Certain Windows-specific network settings # can be pushed to clients, such as DNS # or WINS server addresses. CAVEAT: # http://openvpn.net/faq.html#dhcpcaveats # The addresses below refer to the public # DNS servers provided by opendns.com. ;push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" # Uncomment this directive to allow different # clients to be able to "see" each other. # By default, clients will only see the server. # To force clients to only see the server, you # will also need to appropriately firewall the # server's TUN/TAP interface. ;client-to-client # Uncomment this directive if multiple clients # might connect with the same certificate/key # files or common names. This is recommended # only for testing purposes. For production use, # each client should have its own certificate/key # pair. # # IF YOU HAVE NOT GENERATED INDIVIDUAL # CERTIFICATE/KEY PAIRS FOR EACH CLIENT, # EACH HAVING ITS OWN UNIQUE "COMMON NAME", # UNCOMMENT THIS LINE OUT. ;duplicate-cn # The keepalive directive causes ping-like # messages to be sent back and forth over # the link so that each side knows when # the other side has gone down. # Ping every 10 seconds, assume that remote # peer is down if no ping received during # a 120 second time period. keepalive 10 120 # For extra security beyond that provided # by SSL/TLS, create an "HMAC firewall" # to help block DoS attacks and UDP port flooding. # # Generate with: # openvpn --genkey --secret ta.key # # The server and each client must have # a copy of this key. # The second parameter should be '0' # on the server and '1' on the clients. ;tls-auth ta.key 0 # This file is secret # Select a cryptographic cipher. # This config item must be copied to # the client config file as well. ;cipher BF-CBC # Blowfish (default) ;cipher AES-128-CBC # AES ;cipher DES-EDE3-CBC # Triple-DES # Enable compression on the VPN link. # If you enable it here, you must also # enable it in the client config file. comp-lzo # The maximum number of concurrently connected # clients we want to allow. ;max-clients 100 # It's a good idea to reduce the OpenVPN # daemon's privileges after initialization. # # You can uncomment this out on # non-Windows systems. ;user nobody ;group nogroup # The persist options will try to avoid # accessing certain resources on restart # that may no longer be accessible because # of the privilege downgrade. persist-key persist-tun # Output a short status file showing # current connections, truncated # and rewritten every minute. status openvpn-status.log # By default, log messages will go to the syslog (or # on Windows, if running as a service, they will go to # the "\Program Files\OpenVPN\log" directory). # Use log or log-append to override this default. # "log" will truncate the log file on OpenVPN startup, # while "log-append" will append to it. Use one # or the other (but not both). ;log openvpn.log ;log-append openvpn.log # Set the appropriate level of log # file verbosity. # # 0 is silent, except for fatal errors # 4 is reasonable for general usage # 5 and 6 can help to debug connection problems # 9 is extremely verbose verb 3 # Silence repeating messages. At most 20 # sequential messages of the same message # category will be output to the log. ;mute 20 I've tried on multiple computers by the way. The same result on all of them. What could be wrong? Thanks in advance, and if you need other information I'll gladly post it. Information for new comments root@vps:~# iptables -L -n -v Chain INPUT (policy ACCEPT 862K packets, 51M bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 3 packets, 382 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 4641 298K ACCEPT all -- * * 10.8.0.0/24 0.0.0.0/0 0 0 REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT 1671K packets, 2378M bytes) pkts bytes target prot opt in out source destination And root@vps:~# iptables -t nat -L -n -v Chain PREROUTING (policy ACCEPT 17937 packets, 2013K bytes) pkts bytes target prot opt in out source destination Chain POSTROUTING (policy ACCEPT 8975 packets, 562K bytes) pkts bytes target prot opt in out source destination 1579 103K SNAT all -- * * 10.8.0.0/24 0.0.0.0/0 to:SERVERIP Chain OUTPUT (policy ACCEPT 8972 packets, 562K bytes) pkts bytes target prot opt in out source destination

Read the article

EC2 instance suddenly refusing SSH connections and won't respond to ping

- by Chris

My instance was running fine and this morning I was able to access a Ruby on Rails app hosted on it. An hour later I suddenly wasn't able to access my site, my SSH connection attempts were refused and the server wasn't even responding to ping. I didn't change anything on my system during that hour and reboots aren't fixing it. I've never had any problems connecting or pinging the system before. Can someone please help? This is on my production system! OS: CentOS 5 AMI ID: ami-10b55379 Type: m1.small [] ~% ssh -v *****@meeteor.com OpenSSH_5.2p1, OpenSSL 0.9.8l 5 Nov 2009 debug1: Reading configuration data /etc/ssh_config debug1: Connecting to meeteor.com [184.73.235.191] port 22. debug1: connect to address 184.73.235.191 port 22: Connection refused ssh: connect to host meeteor.com port 22: Connection refused [] ~% ping meeteor.com PING meeteor.com (184.73.235.191): 56 data bytes Request timeout for icmp_seq 0 Request timeout for icmp_seq 1 Request timeout for icmp_seq 2 ^C --- meeteor.com ping statistics --- 4 packets transmitted, 0 packets received, 100.0% packet loss [] ~% ========= System Log ========= Restarting system. Linux version 2.6.16-xenU ([email protected]) (gcc version 4.0.1 20050727 (Red Hat 4.0.1-5)) #1 SMP Mon May 28 03:41:49 SAST 2007 BIOS-provided physical RAM map: Xen: 0000000000000000 - 000000006a400000 (usable) 980MB HIGHMEM available. 727MB LOWMEM available. NX (Execute Disable) protection: active IRQ lockup detection disabled Built 1 zonelists Kernel command line: root=/dev/sda1 ro 4 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 65536 bytes) Xen reported: 2599.998 MHz processor. Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Software IO TLB disabled vmalloc area: ee000000-f53fe000, maxmem 2d7fe000 Memory: 1718700k/1748992k available (1958k kernel code, 20948k reserved, 620k data, 144k init, 1003528k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 5202.30 BogoMIPS (lpj=26011526) Mount-cache hash table entries: 512 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) Checking 'hlt' instruction... OK. Brought up 1 CPUs migration_cost=0 Grant table initialized NET: Registered protocol family 16 Brought up 1 CPUs xen_mem: Initialising balloon driver. highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered i8042.c: No controller found. RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Xen virtual console successfully installed as tty1 Event-channel device installed. netfront: Initialising virtual ethernet driver. mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 NET: Registered protocol family 2 Registering block device major 8 IP route cache hash table entries: 65536 (order: 6, 262144 bytes) TCP established hash table entries: 262144 (order: 9, 2097152 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 Using IPI No-Shortcut mode md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 144k freed *************************************************************** *************************************************************** ** WARNING: Currently emulating unsupported memory accesses ** ** in /lib/tls glibc libraries. The emulation is ** ** slow. To ensure full performance you should ** ** install a 'xen-friendly' (nosegneg) version of ** ** the library, or disable tls support by executing ** ** the following as root: ** ** mv /lib/tls /lib/tls.disabled ** ** Offending process: init (pid=1) ** *************************************************************** *************************************************************** Pausing... 5Pausing... 4Pausing... 3Pausing... 2Pausing... 1Continuing... INIT: version 2.86 booting Welcome to CentOS release 5.4 (Final) Press 'I' to enter interactive startup. Setting clock : Fri Oct 1 14:35:26 EDT 2010 [ OK ] Starting udev: [ OK ] Setting hostname localhost.localdomain: [ OK ] No devices found Setting up Logical Volume Management: [ OK ] Checking filesystems Checking all file systems. [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a /dev/sda1 /dev/sda1: clean, 275424/1310720 files, 1161123/2621440 blocks [ OK ] Remounting root filesystem in read-write mode: [ OK ] Mounting local filesystems: [ OK ] Enabling local filesystem quotas: [ OK ] Enabling /etc/fstab swaps: [ OK ] INIT: Entering runlevel: 4 Entering non-interactive startup Starting background readahead: [ OK ] Applying ip6tables firewall rules: modprobe: FATAL: Module ip6_tables not found. ip6tables-restore v1.3.5: ip6tables-restore: unable to initializetable 'filter' Error occurred at line: 3 Try `ip6tables-restore -h' or 'ip6tables-restore --help' for more information. [FAILED] Applying iptables firewall rules: [ OK ] Loading additional iptables modules: ip_conntrack_netbios_ns [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface eth0: Determining IP information for eth0... done. [ OK ] Starting auditd: [FAILED] Starting irqbalance: [ OK ] Starting portmap: [ OK ] FATAL: Module lockd not found. Starting NFS statd: [ OK ] Starting RPC idmapd: FATAL: Module sunrpc not found. FATAL: Error running install command for sunrpc Error: RPC MTAB does not exist. Starting system message bus: [ OK ] Starting Bluetooth services:[ OK ] [ OK ] Can't open RFCOMM control socket: Address family not supported by protocol Mounting other filesystems: [ OK ] Starting PC/SC smart card daemon (pcscd): [ OK ] Starting hidd: Can't open HIDP control socket: Address family not supported by protocol [FAILED] Starting autofs: Starting automount: automount: test mount forbidden or incorrect kernel protocol version, kernel protocol version 5.00 or above required. [FAILED] [FAILED] Starting sshd: [ OK ] Starting cups: [ OK ] Starting sendmail: [ OK ] Starting sm-client: [ OK ] Starting console mouse services: no console device found[FAILED] Starting crond: [ OK ] Starting xfs: [ OK ] Starting anacron: [ OK ] Starting atd: [ OK ] % Total % Received % Xferd Average Speed Time Time Time Current Dload Upload Total Spent Left Speed 100 390 100 390 0 0 58130 0 --:--:-- --:--:-- --:--:-- 58130 100 390 100 390 0 0 56984 0 --:--:-- --:--:-- --:--:-- 0 Starting yum-updatesd: [ OK ] Starting Avahi daemon... [ OK ] Starting HAL daemon: [ OK ] Starting OSSEC: [ OK ] Starting smartd: [ OK ] c CentOS release 5.4 (Final) Kernel 2.6.16-xenU on an i686 domU-12-31-39-00-C4-97 login: INIT: Id "2" respawning too fast: disabled for 5 minutes INIT: Id "3" respawning too fast: disabled for 5 minutes INIT: Id "4" respawning too fast: disabled for 5 minutes INIT: Id "5" respawning too fast: disabled for 5 minutes INIT: Id "6" respawning too fast: disabled for 5 minutes

Read the article

Unstable DNS with bind

- by yasser abd

we have a Centos machine called jupiter, on which I have installed bind9, On every other machine the DNS is set to be the IP address of jupiter (192.168.2.101), as you can see in the output of the following command in windows >ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : mypcs Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetXtreme 57xx Gigabit Controller Physical Address. . . . . . . . . : 00-1A-A0-AC-E4-CC DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::c16d:3ae4:5907:30c4%8(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.2.98(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Thursday, September 20, 2012 10:26:11 AM Lease Expires . . . . . . . . . . : Sunday, September 23, 2012 10:26:10 AM Default Gateway . . . . . . . . . : 192.168.2.1 DHCP Server . . . . . . . . . . . : 192.168.2.1 DHCPv6 IAID . . . . . . . . . . . : 201333408 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-16-3A-50-01-00-1A-A0-AC-E4-CC DNS Servers . . . . . . . . . . . : 192.168.2.101 192.168.2.1 192.168.2.1 NetBIOS over Tcpip. . . . . . . . : Enabled All machines can always nslookup one of the domain (mydomain.com) that is set in the jupiter's DNS server, you can see that in the output of nslookup on the same windows machine: >nslookup mydomain.com Server: UnKnown Address: 192.168.2.101 Name: mydomain.com Address: 192.168.2.100 The problem is, sometimes mydomain.com can not be pinged, here is the output of the ping on the same windows machine >ping mydomain.com Ping request could not find host mydomain.com. Please check the name and try again. This looks very random, and happens once in a while, so the machine can lookup the DNS records but can't ping it, nor can browse the website that is hosted on mydomain.com, which should resolve to 192.168.2.100 On a linux machine that has the same DNS settings, the output of dig command for mydomain is as follows: $ dig mydomain.com ; <<>> DiG 9.8.2rc1-RedHat-9.8.2-0.10.rc1.el6_3.2 <<>> mydomain.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 36090 ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 1, ADDITIONAL: 1 ;; QUESTION SECTION: ;mydomain.com. IN A ;; ANSWER SECTION: mydomain.com. 86400 IN A 192.168.2.100 ;; AUTHORITY SECTION: mydomain.com. 86400 IN NS jupiter. ;; ADDITIONAL SECTION: jupiter. 86400 IN A 192.168.2.101 ;; Query time: 1 msec ;; SERVER: 192.168.2.101#53(192.168.2.101) ;; WHEN: Thu Sep 20 16:32:14 2012 ;; MSG SIZE rcvd: 83 We've never had the same problem on MACs, they always resolve mydomain.com Here is how I have defined mydomain.com on Bind9's configs on Jupiter, notice that the name of the machine on 192.168.2.100 is venus, so I have this file: /var/named/named.venus: $TTL 1D @ IN SOA jupiter. admin.ourcompany.com. ( 2003052800 ; serial 86400 ; refresh 300 ; retry 604800 ; expire 3600 ; minimum ) @ IN NS jupiter. @ IN A 192.168.2.100 * IN A 192.168.2.100 /var/named/zones/named.venus.zone zone "mydomain.com" IN {type master;file "/var/named/named.venus";allow-update {none;};}; One thing to note is that I haven't defined reverse DNS lookups, only the forward DNS lookups are defined in Bind9 configs, not sure if that's relevant or not. So my question is, why is this being so unstable? what could be the cause?

Read the article

How does Windows 7 DNS client work?

- by Mark Allison

I am using a local DHCP and DNS server on my home network on a linux machine. It is running CentOS 6.3 with dnsmasq 2.48. It's all working fine except for local DNS lookups for Windows machines only. I have a mix of Ubuntu, CentOS and Windows machines on the network, some virtual, some physical. I have a machine called boron and the domain is called localdomain If I ping boron from any linux machine, I get [root@lithium lists]# ping -c3 boron PING boron.localdomain (10.0.0.5) 56(84) bytes of data. 64 bytes from boron.localdomain (10.0.0.5): icmp_seq=1 ttl=64 time=0.740 ms 64 bytes from boron.localdomain (10.0.0.5): icmp_seq=2 ttl=64 time=0.478 ms 64 bytes from boron.localdomain (10.0.0.5): icmp_seq=3 ttl=64 time=0.458 ms --- boron.localdomain ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2000ms rtt min/avg/max/mdev = 0.458/0.558/0.740/0.131 ms If I do it from my Windows 7 machine, I get: Ping request could not find host boron. Please check the name and try again. If I try ping boron.localdomain I get: Pinging boron.localdomain [67.215.65.132] with 32 bytes of data: Reply from 67.215.65.132: bytes=32 time=16ms TTL=57 Reply from 67.215.65.132: bytes=32 time=188ms TTL=57 Reply from 67.215.65.132: bytes=32 time=15ms TTL=57 Reply from 67.215.65.132: bytes=32 time=14ms TTL=57 Ping statistics for 67.215.65.132: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 14ms, Maximum = 188ms, Average = 58ms which is clearly wrong. Why is it going out to the internet? Why can't my windows machine resolve the boron hostname to a FQDN? My Windows machines and linux machines get their network config from DHCP. UPDATE If I do ipconfig /all in Windows, it looks as I would expect: Windows IP Configuration Host Name . . . . . . . . . . . . : lanthanum Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : .localdomain Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : .localdomain Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 50-E5-49-38-FC-A2 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 10.0.0.57(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 23 August 2012 13:58:45 Lease Expires . . . . . . . . . . : 24 August 2012 07:58:48 Default Gateway . . . . . . . . . : 10.0.0.6 DHCP Server . . . . . . . . . . . : 10.0.0.6 DNS Servers . . . . . . . . . . . : 10.0.0.6 208.67.222.222 208.67.220.220 NetBIOS over Tcpip. . . . . . . . : Enabled When I do an nslookup I get: Server: carbon.localdomain Address: 10.0.0.6 *** carbon.localdomain can't find boron: Unspecified error However if I do ifconfig -a in Linux I get: [root@nitrogen ~]# ifconfig -a eth0 Link encap:Ethernet HWaddr 00:0C:29:AF:EC:2A inet addr:10.0.0.7 Bcast:10.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:187687 errors:0 dropped:0 overruns:0 frame:0 TX packets:5857 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:23910700 (22.8 MiB) TX bytes:712964 (696.2 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:329894 errors:0 dropped:0 overruns:0 frame:0 TX packets:329894 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:67153143 (64.0 MiB) TX bytes:67153143 (64.0 MiB) and nslookup: [root@nitrogen ~]# nslookup boron Server: 10.0.0.6 Address: 10.0.0.6#53 Name: boron Address: 10.0.0.5 Both machines are on the same network using the same DHCP server. UPDATE 2 I thought the issue was resolved but I am getting intermittent DNS resolving issues but only on my Windows 7 machine. All my linux boxes are fine. This is what happens when I ping and nslookup from Windows to a Windows 2008 Server: C:\Users\mark>nslookup magnesium Server: carbon.localdomain Address: 10.0.0.6 Name: magnesium.localdomain Address: 10.0.0.12 C:\Users\mark>ping magnesium Pinging magnesium.localdomain [67.215.65.132] with 32 bytes of data: Reply from 67.215.65.132: bytes=32 time=267ms TTL=57 Reply from 67.215.65.132: bytes=32 time=162ms TTL=57 Reply from 67.215.65.132: bytes=32 time=510ms TTL=57 Reply from 67.215.65.132: bytes=32 time=146ms TTL=57 Ping statistics for 67.215.65.132: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 146ms, Maximum = 510ms, Average = 271ms And from Linux: [root@beryllium ~]# ping -c4 magnesium PING magnesium.localdomain (10.0.0.12) 56(84) bytes of data. 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=1 ttl=128 time=0.176 ms 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=2 ttl=128 time=0.634 ms 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=3 ttl=128 time=0.685 ms 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=4 ttl=128 time=0.263 ms --- magnesium.localdomain ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3002ms rtt min/avg/max/mdev = 0.176/0.439/0.685/0.223 ms [root@beryllium ~]# nslookup magnesium Server: 10.0.0.6 Address: 10.0.0.6#53 Name: magnesium.localdomain Address: 10.0.0.12 UPDATE 3 I stopped the Windows DNS client on my Windows 7 machine with net stop dnscache and it is now working fine. It would be nice to get DNS working with the DNS client on, but I might be OK without it, what do you think?

Read the article

Which MAC address is the right one?

- by Paul Dinh

Result by 'getmac': C:\>getmac Physical Address Transport Name =================== ========================================================== 72-03-C6-48-59-34 \Device\Tcpip_{8AEB3263-18C4-449E-A80F-BC2541DDC2A9} 00-21-9B-D5-6F-EE \Device\Tcpip_{C2F9CE19-D68F-4105-9766-45CBE6D82331} 00-22-68-D2-9B-F7 \Device\Tcpip_{A2701130-9221-43FE-8F14-7B1114F84DC3} Result by 'ipconfig /all': C:\>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : xps-m1530 Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Mixed IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Dell Wireless 1395 WLAN Mini-Card Physical Address. . . . . . . . . : 00-22-68-D2-9B-F7 Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Autoconfiguration IP Address. . . : 169.254.246.4 Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Marvell Yukon 88E8040 PCI-E Fast Eth ernet Controller Physical Address. . . . . . . . . : 00-21-9B-D5-6F-EE Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.1.112 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 8.8.8.8 8.8.4.4 Lease Obtained. . . . . . . . . . : 01 November 2012 9:00:36 AM Lease Expires . . . . . . . . . . : 04 November 2012 9:00:36 AM There is a MAC address on the back of my laptop, but the sticker is no longer there. So I use the 'getmac' command to get the MAC addresses. But which address shown by 'getmac' above is the one matching the MAC in the sticker on the back of my laptop? Or am I mistaken something? 00-21-... is the ethernet adapter, 00-22-... is the wireless adapter, and 72-03-... is what?

Read the article

WiFi & GbE Slow while Both Active.

- by Mark Tomlin

I'm having a problem with my WiFi network connection when I use my wired GbE connection concurrently on my Laptop. I'm using my WiFi for Internet access, and general web surfing and I'm using my GbE connection to connect to my PlayStation so I can stream media. The WiFi connection is via a Linksys 610N connected to my Cable Modem. Where as the GbE connection is a direct connection from my Ethernet port to the Ethernet port of the PS3 via a Cat-5 cable (no router in between this connection). As soon as I connect the cable from the PS3 to my Ethernet port on my Laptop the WiFi connection slows to a halt, but then allows for a connection to the web as normal but at much slower speeds for the things like BitTorrent that stops completely. It seems to me that Windows can't handle both connections at once. It will have both active but it can only accept and send packets on one device at one time. I can get WiFi connections to work to go to websites and the like, but once I use my GbE connection to share media between my Laptop and my PS3 the Wifi connection dies out and I no longer have access to the internet. I setup my connection on the PS3 and the Laptop following the insturctions posted here: http://forums.finalgear.com/problems/s14e01-ps3-size-problem-40642/#post1188132 And the following is the results of my ipconfig. Windows IP Configuration Host Name . . . . . . . . . . . . : dygear Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter WiFi: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Intel(R) PRO/Wireless 3945ABG Network Connection Physical Address. . . . . . . . . : 00-19-**-**-**-** Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.1.111 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 192.168.1.1 167.206.254.2 167.206.254.1 Lease Obtained. . . . . . . . . . : Wednesday, May 19, 2010 08:55:30 Lease Expires . . . . . . . . . . : Thursday, May 20, 2010 08:55:30 Ethernet adapter LAN: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet Physical Address. . . . . . . . . : 00-16-**-**-**-** Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.1.50 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Any ideas?

Read the article

Unexpected multiple network connections on Windows Vista

- by Jens

My Network and Sharing Center shows multiple connections to the internet, where only one is expected: My internet access works fine, but since the "Unidentified Network" is set to public after each boot, sharing and network discovery don't work as well. Similar questions on Google point mostly to the Bonjour service, but I am sure that this is not, and never was, installed on this machine. So: How can I get rid of the unidentified network? Output of ipconfig /all: Windows IP Configuration Host Name . . . . . . . . . . . . : ***** Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : mySuffix Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : mySuffix Description . . . . . . . . . . . : Intel(R) 82567LF-3 Gigabit Network Connection Physical Address. . . . . . . . . : 00-19-99-65-F0-B2 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::c90:2d23:7651:42f%10(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.141.130(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 13 November 2012 09:40:54 Lease Expires . . . . . . . . . . : 21 November 2012 09:45:01 Default Gateway . . . . . . . . . : 192.168.141.109 192.168.141.108 DHCP Server . . . . . . . . . . . : 192.168.141.120 DHCPv6 IAID . . . . . . . . . . . : 218110361 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-12-DD-00-AF-00-19-99-65-F0-B2 DNS Servers . . . . . . . . . . . : 8.8.8.8 8.8.4.4 NetBIOS over Tcpip. . . . . . . . : Enabled Tunnel adapter Local Area Connection* 13: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : mySuffix Description . . . . . . . . . . . : Microsoft ISATAP Adapter Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes

Read the article

Can't ping localhost/or reach locally hosted domain

- by Ian

I can't reach a locally hosted domain, and in testing I have discovered I can't ping localhost or the actual IP either. OS is Windows7 64bit, Pro. DNS works, I can ping others on my network, they can ping me, and they can reach the hosted domain. The ONLY problem I have found is that I can't reach the locally hosted domains! C:\Users\ianipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : leda Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : hcs Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : hcs Description . . . . . . . . . . . : Atheros AR8121/AR8113/AR8114 PCI-E Ethern et Controller Physical Address. . . . . . . . . : 00-23-54-7C-E2-2A DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.0.12(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.1 DNS Servers . . . . . . . . . . . : 192.168.0.1 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter VirtualBox Host-Only Network #2: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VirtualBox Host-Only Ethernet Adapter #2 Physical Address. . . . . . . . . : 08-00-27-00-88-4A DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Autoconfiguration IPv4 Address. . : 169.254.205.215(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : NetBIOS over Tcpip. . . . . . . . : Enabled C:\Users\ianping localhost Pinging leda [127.0.0.1] with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for 127.0.0.1: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), C:\Users\ianping coachmaster.leda.hcs Pinging coachmaster.leda.hcs [192.168.0.12] with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for 192.168.0.12: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), C:\Users\ian I can reach a hosted VM in VirtualBox and the VM can browse the hosted sites. I've removed Zone Alarm and disabled Windows Firewall - same results. So how can I browse my locally hosted sited? What could be blocking it? Thanks Ian

Read the article

connecting to a network using route command

- by ami

I have a computer with an external IP(192.168.223.220) and also an internal address (10.1.1.20) in order to connect to some servers that don't have external addresses only 10.1.1.xx . in order to connect to these servers from other machines I used the following command "route ADD 10.1.1.0 MASK 255.255.255.0 192.168.223.220" and than I was able to connect to the servers using there 10.1.1.xx address. The problem is that the hard disk of main server(192.168.223.220) died and was replaced and after the that I am not able to connect to the servers as before, the route command succeeds and I can ping 10.1.1.20 but not the other servers. Thanks I am using Windows XP and the print outs are D:\AurosHome\Scriptsipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : N100-master Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Local Area Connection 3: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Intel(R) PRO/1000 EB Network Connection with I/O Acceleration #2 Physical Address. . . . . . . . . : 00-30-48-34-BA-B9 Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.225.180 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.225.254 DNS Servers . . . . . . . . . . . : 192.168.225.2 Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Intel(R) PRO/1000 EB Network Connection with I/O Acceleration Physical Address. . . . . . . . . : 00-30-48-34-BA-B8 Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 10.1.1.20 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection 2: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Mellanox IPoIB Adapter Physical Address. . . . . . . . . : 00-02-C9-25-34-0D D:\AurosHome\Scriptsroute print Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...00 30 48 34 ba b9 ...... Intel(R) PRO/1000 EB Network Connection with I/O Acceleration #2 - Packet Sche duler Miniport 0x3 ...00 30 48 34 ba b8 ...... Intel(R) PRO/1000 EB Network Connection with I/O Acceleration - Packet Schedul er Miniport 0x10005 ...00 02 c9 25 34 0d ...... Mellanox IPoIB Adapter - Packet Scheduler Miniport =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.225.254 192.168.225.180 10 10.1.1.0 255.255.255.0 10.1.1.20 10.1.1.20 10 10.1.1.20 255.255.255.255 127.0.0.1 127.0.0.1 10 10.255.255.255 255.255.255.255 10.1.1.20 10.1.1.20 10 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.225.0 255.255.255.0 192.168.225.180 192.168.225.180 10 192.168.225.180 255.255.255.255 127.0.0.1 127.0.0.1 10 192.168.225.255 255.255.255.255 192.168.225.180 192.168.225.180 10 224.0.0.0 240.0.0.0 10.1.1.20 10.1.1.20 10 224.0.0.0 240.0.0.0 192.168.225.180 192.168.225.180 10 255.255.255.255 255.255.255.255 10.1.1.20 10.1.1.20 1 255.255.255.255 255.255.255.255 10.1.1.20 10005 1 255.255.255.255 255.255.255.255 192.168.225.180 192.168.225.180 1 Default Gateway: 192.168.225.254 Persistent Routes: None

Read the article

Tip/Trick: Fix Common SEO Problems Using the URL Rewrite Extension

- by ScottGu

Search engine optimization (SEO) is important for any publically facing web-site. A large % of traffic to sites now comes directly from search engines, and improving your site’s search relevancy will lead to more users visiting your site from search engine queries. This can directly or indirectly increase the money you make through your site. This blog post covers how you can use the free Microsoft URL Rewrite Extension to fix a bunch of common SEO problems that your site might have. It takes less than 15 minutes (and no code changes) to apply 4 simple URL Rewrite rules to your site, and in doing so cause search engines to drive more visitors and traffic to your site. The techniques below work equally well with both ASP.NET Web Forms and ASP.NET MVC based sites. They also works with all versions of ASP.NET (and even work with non-ASP.NET content). [In addition to blogging, I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu] Measuring the SEO of your website with the Microsoft SEO Toolkit A few months ago I blogged about the free SEO Toolkit that we’ve shipped. This useful tool enables you to automatically crawl/scan your site for SEO correctness, and it then flags any SEO issues it finds. I highly recommend downloading and using the tool against any public site you work on. It makes it easy to spot SEO issues you might have in your site, and pinpoint ways to optimize it further. Below is a simple example of a report I ran against one of my sites (www.scottgu.com) prior to applying the URL Rewrite rules I’ll cover later in this blog post: Search Relevancy and URL Splitting Two of the important things that search engines evaluate when assessing your site’s “search relevancy” are: How many other sites link to your content. Search engines assume that if a lot of people around the web are linking to your content, then it is likely useful and so weight it higher in relevancy. The uniqueness of the content it finds on your site. If search engines find that the content is duplicated in multiple places around the Internet (or on multiple URLs on your site) then it is likely to drop the relevancy of the content. One of the things you want to be very careful to avoid when building public facing sites is to not allow different URLs to retrieve the same content within your site. Doing so will hurt with both of the situations above. In particular, allowing external sites to link to the same content with multiple URLs will cause your link-count and page-ranking to be split up across those different URLs (and so give you a smaller page rank than what it would otherwise be if it was just one URL). Not allowing external sites to link to you in different ways sounds easy in theory – but you might wonder what exactly this means in practice and how you avoid it. 4 Really Common SEO Problems Your Sites Might Have Below are 4 really common scenarios that can cause your site to inadvertently expose multiple URLs for the same content. When this happens external sites linking to yours will end up splitting their page links across multiple URLs - and as a result cause you to have a lower page ranking with search engines than you deserve. SEO Problem #1: Default Document IIS (and other web servers) supports the concept of a “default document”. This allows you to avoid having to explicitly specify the page you want to serve at either the root of the web-site/application, or within a sub-directory. This is convenient – but means that by default this content is available via two different publically exposed URLs (which is bad). For example: http://scottgu.com/ http://scottgu.com/default.aspx SEO Problem #2: Different URL Casings Web developers often don’t realize URLs are case sensitive to search engines on the web. This means that search engines will treat the following links as two completely different URLs: http://scottgu.com/Albums.aspx http://scottgu.com/albums.aspx SEO Problem #3: Trailing Slashes Consider the below two URLs – they might look the same at first, but they are subtly different. The trailing slash creates yet another situation that causes search engines to treat the URLs as different and so split search rankings: http://scottgu.com http://scottgu.com/ SEO Problem #4: Canonical Host Names Sometimes sites support scenarios where they support a web-site with both a leading “www” hostname prefix as well as just the hostname itself. This causes search engines to treat the URLs as different and split search rankling: http://scottgu.com/albums.aspx/ http://www.scottgu.com/albums.aspx/ How to Easily Fix these SEO Problems in 10 minutes (or less) using IIS Rewrite If you haven’t been careful when coding your sites, chances are you are suffering from one (or more) of the above SEO problems. Addressing these issues will improve your search engine relevancy ranking and drive more traffic to your site. The “good news” is that fixing the above 4 issues is really easy using the URL Rewrite Extension. This is a completely free Microsoft extension available for IIS 7.x (on Windows Server 2008, Windows Server 2008 R2, Windows 7 and Windows Vista). The great thing about using the IIS Rewrite extension is that it allows you to fix the above problems *without* having to change any code within your applications. You can easily install the URL Rewrite Extension in under 3 minutes using the Microsoft Web Platform Installer (a free tool we ship that automates setting up web servers and development machines). Just click the green “Install Now” button on the URL Rewrite Spotlight page to install it on your Windows Server 2008, Windows 7 or Windows Vista machine: Once installed you’ll find that a new “URL Rewrite” icon is available within the IIS 7 Admin Tool: Double-clicking the icon will open up the URL Rewrite admin panel – which will display the list of URL Rewrite rules configured for a particular application or site: Notice that our rewrite rule list above is currently empty (which is the default when you first install the extension). We can click the “Add Rule…” link button in the top-right of the panel to add and enable new URL Rewriting logic for our site. Scenario 1: Handling Default Document Scenarios One of the SEO problems I discussed earlier in this post was the scenario where the “default document” feature of IIS causes you to inadvertently expose two URLs for the same content on your site. For example: http://scottgu.com/ http://scottgu.com/default.aspx We can fix this by adding a new IIS Rewrite rule that automatically redirects anyone who navigates to the second URL to instead go to the first one. We will setup the HTTP redirect to be a “permanent redirect” – which will indicate to search engines that they should follow the redirect and use the new URL they are redirected to as the identifier of the content they retrieve. Let’s look at how we can create such a rule. We’ll begin by clicking the “Add Rule” link in the screenshot above. This will cause the below dialog to display: We’ll select the “Blank Rule” template within the “Inbound rules” section to create a new custom URL Rewriting rule. This will display an empty pane like below: Don’t worry – setting up the above rule is easy. The following 4 steps explain how to do so: Step 1: Name the Rule Our first step will be to name the rule we are creating. Naming it with a descriptive name will make it easier to find and understand later. Let’s name this rule our “Default Document URL Rewrite” rule: Step 2: Setup the Regular Expression that Matches this Rule Our second step will be to specify a regular expression filter that will cause this rule to execute when an incoming URL matches the regex pattern. Don’t worry if you aren’t good with regular expressions - I suck at them too. The trick is to know someone who is good at them or copy/paste them from a web-site. Below we are going to specify the following regular expression as our pattern rule: (.*?)/?Default\.aspx$ This pattern will match any URL string that ends with Default.aspx. The "(.*?)" matches any preceding character zero or more times. The "/?" part says to match the slash symbol zero or one times. The "$" symbol at the end will ensure that the pattern will only match strings that end with Default.aspx. Combining all these regex elements allows this rule to work not only for the root of your web site (e.g. http://scottgu.com/default.aspx) but also for any application or subdirectory within the site (e.g. http://scottgu.com/photos/default.aspx. Because the “ignore case” checkbox is selected it will match both “Default.aspx” as well as “default.aspx” within the URL. One nice feature built-into the rule editor is a “Test pattern” button that you can click to bring up a dialog that allows you to test out a few URLs with the rule you are configuring: Above I've added a “products/default.aspx” URL and clicked the “Test” button. This will give me immediate feedback on whether the rule will execute for it. Step 3: Setup a Permanent Redirect Action We’ll then setup an action to occur when our regular expression pattern matches the incoming URL: In the dialog above I’ve changed the “Action Type” drop down to be a “Redirect” action. The “Redirect Type” will be a HTTP 301 Permanent redirect – which means search engines will follow it. I’ve also set the “Redirect URL” property to be: {R:1}/ This indicates that we want to redirect the web client requesting the original URL to a new URL that has the originally requested URL path - minus the "Default.aspx" in it. For example, requests for http://scottgu.com/default.aspx will be redirected to http://scottgu.com/, and requests for http://scottgu.com/photos/default.aspx will be redirected to http://scottgu.com/photos/ The "{R:N}" regex construct, where N >= 0, is called a back-reference and N is the back-reference index. In the case of our pattern "(.*?)/?Default\.aspx$", if the input URL is "products/Default.aspx" then {R:0} will contain "products/Default.aspx" and {R:1} will contain "products". We are going to use this {R:1}/ value to be the URL we redirect users to. Step 4: Apply and Save the Rule Our final step is to click the “Apply” button in the top right hand of the IIS admin tool – which will cause the tool to persist the URL Rewrite rule into our application’s root web.config file (under a <system.webServer/rewrite> configuration section): <configuration> <system.webServer> <rewrite> <rules> <rule name="Default Document" stopProcessing="true"> <match url="(.*?)/?Default\.aspx$" /> <action type="Redirect" url="{R:1}/" /> </rule> </rules> </rewrite> </system.webServer> </configuration> Because IIS 7.x and ASP.NET share the same web.config files, you can actually just copy/paste the above code into your web.config files using Visual Studio and skip the need to run the admin tool entirely. This also makes adding/deploying URL Rewrite rules with your ASP.NET applications really easy. Step 5: Try the Rule Out Now that we’ve saved the rule, let’s try it out on our site. Try the following two URLs on my site: http://scottgu.com/ http://scottgu.com/default.aspx Notice that the second URL automatically redirects to the first one. Because it is a permanent redirect, search engines will follow the URL and should update the page ranking of http://scottgu.com to include links to http://scottgu.com/default.aspx as well. Scenario 2: Different URL Casing Another common SEO problem I discussed earlier in this post is that URLs are case sensitive to search engines on the web. This means that search engines will treat the following links as two completely different URLs: http://scottgu.com/Albums.aspx http://scottgu.com/albums.aspx We can fix this by adding a new IIS Rewrite rule that automatically redirects anyone who navigates to the first URL to instead go to the second (all lower-case) one. Like before, we will setup the HTTP redirect to be a “permanent redirect” – which will indicate to search engines that they should follow the redirect and use the new URL they are redirected to as the identifier of the content they retrieve. To create such a rule we’ll click the “Add Rule” link in the URL Rewrite admin tool again. This will cause the “Add Rule” dialog to appear again: Unlike the previous scenario (where we created a “Blank Rule”), with this scenario we can take advantage of a built-in “Enforce lowercase URLs” rule template. When we click the “ok” button we’ll see the following dialog which asks us if we want to create a rule that enforces the use of lowercase letters in URLs: When we click the “Yes” button we’ll get a pre-written rule that automatically performs a permanent redirect if an incoming URL has upper-case characters in it – and automatically send users to a lower-case version of the URL: We can click the “Apply” button to use this rule “as-is” and have it apply to all incoming URLs to our site. Because my www.scottgu.com site uses ASP.NET Web Forms, I’m going to make one small change to the rule we generated above – which is to add a condition that will ensure that URLs to ASP.NET’s built-in “WebResource.axd” handler are excluded from our case-sensitivity URL Rewrite logic. URLs to the WebResource.axd handler will only come from server-controls emitted from my pages – and will never be linked to from external sites. While my site will continue to function fine if we redirect these URLs to automatically be lower-case – doing so isn’t necessary and will add an extra HTTP redirect to many of my pages. The good news is that adding a condition that prevents my URL Rewriting rule from happening with certain URLs is easy. We simply need to expand the “Conditions” section of the form above We can then click the “Add” button to add a condition clause. This will bring up the “Add Condition” dialog: Above I’ve entered {URL} as the Condition input – and said that this rule should only execute if the URL does not match a regex pattern which contains the string “WebResource.axd”. This will ensure that WebResource.axd URLs to my site will be allowed to execute just fine without having the URL be re-written to be all lower-case. Note: If you have static resources (like references to .jpg, .css, and .js files) within your site that currently use upper-case characters you’ll probably want to add additional condition filter clauses so that URLs to them also don’t get redirected to be lower-case (just add rules for patterns like .jpg, .gif, .js, etc). Your site will continue to work fine if these URLs get redirected to be lower case (meaning the site won’t break) – but it will cause an extra HTTP redirect to happen on your site for URLs that don’t need to be redirected for SEO reasons. So setting up a condition clause makes sense to add. When I click the “ok” button above and apply our lower-case rewriting rule the admin tool will save the following additional rule to our web.config file: <configuration> <system.webServer> <rewrite> <rules> <rule name="Default Document" stopProcessing="true"> <match url="(.*?)/?Default\.aspx$" /> <action type="Redirect" url="{R:1}/" /> </rule> <rule name="Lower Case URLs" stopProcessing="true"> <match url="[A-Z]" ignoreCase="false" /> <conditions logicalGrouping="MatchAll" trackAllCaptures="false"> <add input="{URL}" pattern="WebResource.axd" negate="true" /> </conditions> <action type="Redirect" url="{ToLower:{URL}}" /> </rule> </rules> </rewrite> </system.webServer> </configuration> Try the Rule Out Now that we’ve saved the rule, let’s try it out on our site. Try the following two URLs on my site: http://scottgu.com/Albums.aspx http://scottgu.com/albums.aspx Notice that the first URL (which has a capital “A”) automatically does a redirect to a lower-case version of the URL. Scenario 3: Trailing Slashes Another common SEO problem I discussed earlier in this post is the scenario of trailing slashes within URLs. The trailing slash creates yet another situation that causes search engines to treat the URLs as different and so split search rankings: http://scottgu.com http://scottgu.com/ We can fix this by adding a new IIS Rewrite rule that automatically redirects anyone who navigates to the first URL (that does not have a trailing slash) to instead go to the second one that does. Like before, we will setup the HTTP redirect to be a “permanent redirect” – which will indicate to search engines that they should follow the redirect and use the new URL they are redirected to as the identifier of the content they retrieve. To create such a rule we’ll click the “Add Rule” link in the URL Rewrite admin tool again. This will cause the “Add Rule” dialog to appear again: The URL Rewrite admin tool has a built-in “Append or remove the trailing slash symbol” rule template. When we select it and click the “ok” button we’ll see the following dialog which asks us if we want to create a rule that automatically redirects users to a URL with a trailing slash if one isn’t present: Like within our previous lower-casing rewrite rule we’ll add one additional condition clause that will exclude WebResource.axd URLs from being processed by this rule. This will avoid an unnecessary redirect for happening for those URLs. When we click the “OK” button we’ll get a pre-written rule that automatically performs a permanent redirect if the URL doesn’t have a trailing slash – and if the URL is not processed by either a directory or a file. This will save the following additional rule to our web.config file: <configuration> <system.webServer> <rewrite> <rules> <rule name="Default Document" stopProcessing="true"> <match url="(.*?)/?Default\.aspx$" /> <action type="Redirect" url="{R:1}/" /> </rule> <rule name="Lower Case URLs" stopProcessing="true"> <match url="[A-Z]" ignoreCase="false" /> <conditions logicalGrouping="MatchAll" trackAllCaptures="false"> <add input="{URL}" pattern="WebResource.axd" negate="true" /> </conditions> <action type="Redirect" url="{ToLower:{URL}}" /> </rule> <rule name="Trailing Slash" stopProcessing="true"> <match url="(.*[^/])$" /> <conditions logicalGrouping="MatchAll" trackAllCaptures="false"> <add input="{REQUEST_FILENAME}" matchType="IsDirectory" negate="true" /> <add input="{REQUEST_FILENAME}" matchType="IsFile" negate="true" /> <add input="{URL}" pattern="WebResource.axd" negate="true" /> </conditions> <action type="Redirect" url="{R:1}/" /> </rule> </rules> </rewrite> </system.webServer> </configuration> Try the Rule Out Now that we’ve saved the rule, let’s try it out on our site. Try the following two URLs on my site: http://scottgu.com http://scottgu.com/ Notice that the first URL (which has no trailing slash) automatically does a redirect to a URL with the trailing slash. Because it is a permanent redirect, search engines will follow the URL and update the page ranking. Scenario 4: Canonical Host Names The final SEO problem I discussed earlier are scenarios where a site works with both a leading “www” hostname prefix as well as just the hostname itself. This causes search engines to treat the URLs as different and split search rankling: http://www.scottgu.com/albums.aspx http://scottgu.com/albums.aspx We can fix this by adding a new IIS Rewrite rule that automatically redirects anyone who navigates to the first URL (that has a www prefix) to instead go to the second URL. Like before, we will setup the HTTP redirect to be a “permanent redirect” – which will indicate to search engines that they should follow the redirect and use the new URL they are redirected to as the identifier of the content they retrieve. To create such a rule we’ll click the “Add Rule” link in the URL Rewrite admin tool again. This will cause the “Add Rule” dialog to appear again: The URL Rewrite admin tool has a built-in “Canonical domain name” rule template. When we select it and click the “ok” button we’ll see the following dialog which asks us if we want to create a redirect rule that automatically redirects users to a primary host name URL: Above I’m entering the primary URL address I want to expose to the web: scottgu.com. When we click the “OK” button we’ll get a pre-written rule that automatically performs a permanent redirect if the URL has another leading domain name prefix. This will save the following additional rule to our web.config file: <configuration> <system.webServer> <rewrite> <rules> <rule name="Cannonical Hostname"> <match url="(.*)" /> <conditions logicalGrouping="MatchAll" trackAllCaptures="false"> <add input="{HTTP_HOST}" pattern="^scottgu\.com$" negate="true" /> </conditions> <action type="Redirect" url="http://scottgu.com/{R:1}" /> </rule> <rule name="Default Document" stopProcessing="true"> <match url="(.*?)/?Default\.aspx$" /> <action type="Redirect" url="{R:1}/" /> </rule> <rule name="Lower Case URLs" stopProcessing="true"> <match url="[A-Z]" ignoreCase="false" /> <conditions logicalGrouping="MatchAll" trackAllCaptures="false"> <add input="{URL}" pattern="WebResource.axd" negate="true" /> </conditions> <action type="Redirect" url="{ToLower:{URL}}" /> </rule> <rule name="Trailing Slash" stopProcessing="true"> <match url="(.*[^/])$" /> <conditions logicalGrouping="MatchAll" trackAllCaptures="false"> <add input="{REQUEST_FILENAME}" matchType="IsDirectory" negate="true" /> <add input="{REQUEST_FILENAME}" matchType="IsFile" negate="true" /> <add input="{URL}" pattern="WebResource.axd" negate="true" /> </conditions> <action type="Redirect" url="{R:1}/" /> </rule> </rules> </rewrite> </system.webServer> </configuration> Try the Rule Out Now that we’ve saved the rule, let’s try it out on our site. Try the following two URLs on my site: http://www.scottgu.com/albums.aspx http://scottgu.com/albums.aspx Notice that the first URL (which has the “www” prefix) now automatically does a redirect to the second URL which does not have the www prefix. Because it is a permanent redirect, search engines will follow the URL and update the page ranking. 4 Simple Rules for Improved SEO The above 4 rules are pretty easy to setup and should take less than 15 minutes to configure on existing sites you already have. The beauty of using a solution like the URL Rewrite Extension is that you can take advantage of it without having to change code within your web-site – and without having to break any existing links already pointing at your site. Users who follow existing links will be automatically redirected to the new URLs you wish to publish. And search engines will start to give your site a higher search relevancy ranking – which will list your site higher in search results and drive more traffic to it. Customizing your URL Rewriting rules further is easy to-do either by editing the web.config file directly, or alternatively, just double click the URL Rewrite icon within the IIS 7.x admin tool and it will list all the active rules for your web-site or application: Clicking any of the rules above will open the rules editor back up and allow you to tweak/customize/save them further. Summary Measuring and improving SEO is something every developer building a public-facing web-site needs to think about and focus on. If you haven’t already, download and use the SEO Toolkit to analyze the SEO of your sites today. New URL Routing features in ASP.NET MVC and ASP.NET Web Forms 4 make it much easier to build applications that have more control over the URLs that are published. Tools like the URL Rewrite Extension that I’ve talked about in this blog post make it much easier to improve the URLs that are published from sites you already have built today – without requiring you to change a lot of code. The URL Rewrite Extension provides a bunch of additional great capabilities – far beyond just SEO - as well. I’ll be covering these additional capabilities more in future blog posts. Hope this helps, Scott

Read the article

Skinny controller in ASP.NET MVC 4

- by thangchung

Rails community are always inspire a lot of best ideas. I really love this community by the time. One of these is "Fat models and skinny controllers". I have spent a lot of time on ASP.NET MVC, and really I did some miss-takes, because I made the controller so fat. That make controller is really dirty and very hard to maintain in the future. It is violate seriously SRP principle and KISS as well. But how can we achieve that in ASP.NET MVC? That question is really clear after I read "Manning ASP.NET MVC 4 in Action". It is simple that we can separate it into ActionResult, and try to implementing logic and persistence data inside this. In last 2 years, I have read this from Jimmy Bogard blog, but in that time I never had a consideration about it. That's enough for talking now. I just published a sample on ASP.NET MVC 4, implemented on Visual Studio 2012 RC at here. I used EF framework at here for implementing persistence layer, and also use 2 free templates from internet to make the UI for this sample. In this sample, I try to implementing the simple magazine website that managing all articles, categories and news. It is not finished at all in this time, but no problems, because I just show you about how can we make the controller skinny. And I wanna hear more about your ideas. The first thing, I am abstract the base ActionResult class like this: public abstract class MyActionResult : ActionResult, IEnsureNotNull { public abstract void EnsureAllInjectInstanceNotNull(); } public abstract class ActionResultBase<TController> : MyActionResult where TController : Controller { protected readonly Expression<Func<TController, ActionResult>> ViewNameExpression; protected readonly IExConfigurationManager ConfigurationManager; protected ActionResultBase (Expression<Func<TController, ActionResult>> expr) : this(DependencyResolver.Current.GetService<IExConfigurationManager>(), expr) { } protected ActionResultBase( IExConfigurationManager configurationManager, Expression<Func<TController, ActionResult>> expr) { Guard.ArgumentNotNull(expr, "ViewNameExpression"); Guard.ArgumentNotNull(configurationManager, "ConfigurationManager"); ViewNameExpression = expr; ConfigurationManager = configurationManager; } protected ViewResult GetViewResult<TViewModel>(TViewModel viewModel) { var m = (MethodCallExpression)ViewNameExpression.Body; if (m.Method.ReturnType != typeof(ActionResult)) { throw new ArgumentException("ControllerAction method '" + m.Method.Name + "' does not return type ActionResult"); } var result = new ViewResult { ViewName = m.Method.Name }; result.ViewData.Model = viewModel; return result; } public override void ExecuteResult(ControllerContext context) { EnsureAllInjectInstanceNotNull(); } } I also have an interface for validation all inject objects. This interface make sure all inject objects that I inject using Autofac container are not null. The implementation of this as below public interface IEnsureNotNull { void EnsureAllInjectInstanceNotNull(); } Afterwards, I am just simple implementing the HomePageViewModelActionResult class like this public class HomePageViewModelActionResult<TController> : ActionResultBase<TController> where TController : Controller { #region variables & ctors private readonly ICategoryRepository _categoryRepository; private readonly IItemRepository _itemRepository; private readonly int _numOfPage; public HomePageViewModelActionResult(Expression<Func<TController, ActionResult>> viewNameExpression) : this(viewNameExpression, DependencyResolver.Current.GetService<ICategoryRepository>(), DependencyResolver.Current.GetService<IItemRepository>()) { } public HomePageViewModelActionResult( Expression<Func<TController, ActionResult>> viewNameExpression, ICategoryRepository categoryRepository, IItemRepository itemRepository) : base(viewNameExpression) { _categoryRepository = categoryRepository; _itemRepository = itemRepository; _numOfPage = ConfigurationManager.GetAppConfigBy("NumOfPage").ToInteger(); } #endregion #region implementation public override void ExecuteResult(ControllerContext context) { base.ExecuteResult(context); var cats = _categoryRepository.GetCategories(); var mainViewModel = new HomePageViewModel(); var headerViewModel = new HeaderViewModel(); var footerViewModel = new FooterViewModel(); var mainPageViewModel = new MainPageViewModel(); headerViewModel.SiteTitle = "Magazine Website"; if (cats != null && cats.Any()) { headerViewModel.Categories = cats.ToList(); footerViewModel.Categories = cats.ToList(); } mainPageViewModel.LeftColumn = BindingDataForMainPageLeftColumnViewModel(); mainPageViewModel.RightColumn = BindingDataForMainPageRightColumnViewModel(); mainViewModel.Header = headerViewModel; mainViewModel.DashBoard = new DashboardViewModel(); mainViewModel.Footer = footerViewModel; mainViewModel.MainPage = mainPageViewModel; GetViewResult(mainViewModel).ExecuteResult(context); } public override void EnsureAllInjectInstanceNotNull() { Guard.ArgumentNotNull(_categoryRepository, "CategoryRepository"); Guard.ArgumentNotNull(_itemRepository, "ItemRepository"); Guard.ArgumentMustMoreThanZero(_numOfPage, "NumOfPage"); } #endregion #region private functions private MainPageRightColumnViewModel BindingDataForMainPageRightColumnViewModel() { var mainPageRightCol = new MainPageRightColumnViewModel(); mainPageRightCol.LatestNews = _itemRepository.GetNewestItem(_numOfPage).ToList(); mainPageRightCol.MostViews = _itemRepository.GetMostViews(_numOfPage).ToList(); return mainPageRightCol; } private MainPageLeftColumnViewModel BindingDataForMainPageLeftColumnViewModel() { var mainPageLeftCol = new MainPageLeftColumnViewModel(); var items = _itemRepository.GetNewestItem(_numOfPage); if (items != null && items.Any()) { var firstItem = items.First(); if (firstItem == null) throw new NoNullAllowedException("First Item".ToNotNullErrorMessage()); if (firstItem.ItemContent == null) throw new NoNullAllowedException("First ItemContent".ToNotNullErrorMessage()); mainPageLeftCol.FirstItem = firstItem; if (items.Count() > 1) { mainPageLeftCol.RemainItems = items.Where(x => x.ItemContent != null && x.Id != mainPageLeftCol.FirstItem.Id).ToList(); } } return mainPageLeftCol; } #endregion } Final step, I get into HomeController and add some line of codes like this [Authorize] public class HomeController : BaseController { [AllowAnonymous] public ActionResult Index() { return new HomePageViewModelActionResult<HomeController>(x=>x.Index()); } [AllowAnonymous] public ActionResult Details(int id) { return new DetailsViewModelActionResult<HomeController>(x => x.Details(id), id); } [AllowAnonymous] public ActionResult Category(int id) { return new CategoryViewModelActionResult<HomeController>(x => x.Category(id), id); } } As you see, the code in controller is really skinny, and all the logic I move to the custom ActionResult class. Some people said, it just move the code out of controller and put it to another class, so it is still hard to maintain. Look like it just move the complicate codes from one place to another place. But if you have a look and think it in details, you have to find out if you have code for processing all logic that related to HttpContext or something like this. You can do it on Controller, and try to delegating another logic (such as processing business requirement, persistence data,...) to custom ActionResult class. Tell me more your thinking, I am really willing to hear all of its from you guys. All source codes can be find out at here. Tweet !function(d,s,id){var js,fjs=d.getElementsByTagName(s)[0];if(!d.getElementById(id)){js=d.createElement(s);js.id=id;js.src="http://weblogs.asp.net//platform.twitter.com/widgets.js";fjs.parentNode.insertBefore(js,fjs);}}(document,"script","twitter-wjs");

Read the article

FreeBSD performance tuning. Sysctls, loader.conf, kernel

- by SaveTheRbtz

I wanted to share knowledge of tuning FreeBSD via sysctl.conf/loader.conf/KENCONF. It was initially based on Igor Sysoev's (author of nginx) presentation about FreeBSD tuning up to 100,000-200,000 active connections. Tunings are for FreeBSD-CURRENT. Since 7.2 amd64 some of them are tuned well by default. Prior 7.0 some of them are boot only (set via /boot/loader.conf) or does not exist at all. sysctl.conf: # No zero mapping feature # May break wine # (There are also reports about broken samba3) #security.bsd.map_at_zero=0 # If you have really busy webserver with apache13 you may run out of processes #kern.maxproc=10000 # Same for servers with apache2 / Pound #kern.threads.max_threads_per_proc=4096 # Max. backlog size kern.ipc.somaxconn=4096 # Shared memory // 7.2+ can use shared memory > 2Gb kern.ipc.shmmax=2147483648 # Sockets kern.ipc.maxsockets=204800 # Can cause this on older kernels: # http://old.nabble.com/Significant-performance-regression-for-increased-maxsockbuf-on-8.0-RELEASE-tt26745981.html#a26745981 ) kern.ipc.maxsockbuf=10485760 # Mbuf 2k clusters (on amd64 7.2+ 25600 is default) # For such high value vm.kmem_size must be increased to 3G kern.ipc.nmbclusters=262144 # Jumbo pagesize(_SC_PAGESIZE) clusters # Used as general packet storage for jumbo frames # can be monitored via `netstat -m` #kern.ipc.nmbjumbop=262144 # Jumbo 9k/16k clusters # If you are using them #kern.ipc.nmbjumbo9=65536 #kern.ipc.nmbjumbo16=32768 # For lower latency you can decrease scheduler's maximum time slice # default: stathz/10 (~ 13) #kern.sched.slice=1 # Increase max command-line length showed in `ps` (e.g for Tomcat/Java) # Default is PAGE_SIZE / 16 or 256 on x86 # This avoids commands to be presented as [executable] in `ps` # For more info see: http://www.freebsd.org/cgi/query-pr.cgi?pr=120749 kern.ps_arg_cache_limit=4096 # Every socket is a file, so increase them kern.maxfiles=204800 kern.maxfilesperproc=200000 kern.maxvnodes=200000 # On some systems HPET is almost 2 times faster than default ACPI-fast # Useful on systems with lots of clock_gettime / gettimeofday calls # See http://old.nabble.com/ACPI-fast-default-timecounter,-but-HPET-83--faster-td23248172.html # After revision 222222 HPET became default: http://svnweb.freebsd.org/base?view=revision&revision=222222 kern.timecounter.hardware=HPET # Small receive space, only usable on http-server, on file server this # should be increased to 65535 or even more #net.inet.tcp.recvspace=8192 # This is useful on Fat-Long-Pipes #net.inet.tcp.recvbuf_max=10485760 #net.inet.tcp.recvbuf_inc=65535 # Small send space is useful for http servers that serve small files # Autotuned since 7.x net.inet.tcp.sendspace=16384 # This is useful on Fat-Long-Pipes #net.inet.tcp.sendbuf_max=10485760 #net.inet.tcp.sendbuf_inc=65535 # Turn off receive autotuning # You can play with it. #net.inet.tcp.recvbuf_auto=0 #net.inet.tcp.sendbuf_auto=0 # This should be enabled if you going to use big spaces (>64k) # Also timestamp field is useful when using syncookies net.inet.tcp.rfc1323=1 # Turn this off on high-speed, lossless connections (LAN 1Gbit+) # If you set it there is no need in TCP_NODELAY sockopt (see man tcp) net.inet.tcp.delayed_ack=0 # This feature is useful if you are serving data over modems, Gigabit Ethernet, # or even high speed WAN links (or any other link with a high bandwidth delay product), # especially if you are also using window scaling or have configured a large send window. # Automatically disables on small RTT ( http://www.freebsd.org/cgi/cvsweb.cgi/src/sys/netinet/tcp_subr.c?#rev1.237 ) # This sysctl was removed in 10-CURRENT: # See: http://www.mail-archive.com/[email protected]/msg06178.html #net.inet.tcp.inflight.enable=0 # TCP slowstart algorithm tunings # We assuming we have very fast clients #net.inet.tcp.slowstart_flightsize=100 #net.inet.tcp.local_slowstart_flightsize=100 # Disable randomizing of ports to avoid false RST # Before usage check SA here www.bsdcan.org/2006/papers/ImprovingTCPIP.pdf # (it's also says that port randomization auto-disables at some conn.rates, but I didn't checked it thou) #net.inet.ip.portrange.randomized=0 # Increase portrange # For outgoing connections only. Good for seed-boxes and ftp servers. net.inet.ip.portrange.first=1024 net.inet.ip.portrange.last=65535 # # stops route cache degregation during a high-bandwidth flood # http://www.freebsd.org/doc/en/books/handbook/securing-freebsd.html #net.inet.ip.rtexpire=2 net.inet.ip.rtminexpire=2 net.inet.ip.rtmaxcache=1024 # Security net.inet.ip.redirect=0 net.inet.ip.sourceroute=0 net.inet.ip.accept_sourceroute=0 net.inet.icmp.maskrepl=0 net.inet.icmp.log_redirect=0 net.inet.icmp.drop_redirect=1 net.inet.tcp.drop_synfin=1 # # There is also good example of sysctl.conf with comments: # http://www.thern.org/projects/sysctl.conf # # icmp may NOT rst, helpful for those pesky spoofed # icmp/udp floods that end up taking up your outgoing # bandwidth/ifqueue due to all that outgoing RST traffic. # #net.inet.tcp.icmp_may_rst=0 # Security net.inet.udp.blackhole=1 net.inet.tcp.blackhole=2 # IPv6 Security # For more info see http://www.fosslc.org/drupal/content/security-implications-ipv6 # Disable Node info replies # To see this vulnerability in action run `ping6 -a sglAac ::1` or `ping6 -w ::1` on unprotected node net.inet6.icmp6.nodeinfo=0 # Turn on IPv6 privacy extensions # For more info see proposal http://unix.derkeiler.com/Mailing-Lists/FreeBSD/net/2008-06/msg00103.html net.inet6.ip6.use_tempaddr=1 net.inet6.ip6.prefer_tempaddr=1 # Disable ICMP redirect net.inet6.icmp6.rediraccept=0 # Disable acceptation of RA and auto linklocal generation if you don't use them #net.inet6.ip6.accept_rtadv=0 #net.inet6.ip6.auto_linklocal=0 # Increases default TTL, sometimes useful # Default is 64 net.inet.ip.ttl=128 # Lessen max segment life to conserve resources # ACK waiting time in miliseconds # (default: 30000. RFC from 1979 recommends 120000) net.inet.tcp.msl=5000 # Max bumber of timewait sockets net.inet.tcp.maxtcptw=200000 # Don't use tw on local connections # As of 15 Apr 2009. Igor Sysoev says that nolocaltimewait has some buggy realization. # So disable it or now till get fixed #net.inet.tcp.nolocaltimewait=1 # FIN_WAIT_2 state fast recycle net.inet.tcp.fast_finwait2_recycle=1 # Time before tcp keepalive probe is sent # default is 2 hours (7200000) #net.inet.tcp.keepidle=60000 # Should be increased until net.inet.ip.intr_queue_drops is zero net.inet.ip.intr_queue_maxlen=4096 # Interrupt handling via multiple CPU, but with context switch. # You can play with it. Default is 1; #net.isr.direct=0 # This is for routers only #net.inet.ip.forwarding=1 #net.inet.ip.fastforwarding=1 # This speed ups dummynet when channel isn't saturated net.inet.ip.dummynet.io_fast=1 # Increase dummynet(4) hash #net.inet.ip.dummynet.hash_size=2048 #net.inet.ip.dummynet.max_chain_len # Should be increased when you have A LOT of files on server # (Increase until vfs.ufs.dirhash_mem becomes lower) vfs.ufs.dirhash_maxmem=67108864 # Note from commit http://svn.freebsd.org/base/head@211031 : # For systems with RAID volumes and/or virtualization envirnments, where # read performance is very important, increasing this sysctl tunable to 32 # or even more will demonstratively yield additional performance benefits. vfs.read_max=32 # Explicit Congestion Notification (see http://en.wikipedia.org/wiki/Explicit_Congestion_Notification) net.inet.tcp.ecn.enable=1 # Flowtable - flow caching mechanism # Useful for routers #net.inet.flowtable.enable=1 #net.inet.flowtable.nmbflows=65535 # Extreme polling tuning #kern.polling.burst_max=1000 #kern.polling.each_burst=1000 #kern.polling.reg_frac=100 #kern.polling.user_frac=1 #kern.polling.idle_poll=0 # IPFW dynamic rules and timeouts tuning # Increase dyn_buckets till net.inet.ip.fw.curr_dyn_buckets is lower net.inet.ip.fw.dyn_buckets=65536 net.inet.ip.fw.dyn_max=65536 net.inet.ip.fw.dyn_ack_lifetime=120 net.inet.ip.fw.dyn_syn_lifetime=10 net.inet.ip.fw.dyn_fin_lifetime=2 net.inet.ip.fw.dyn_short_lifetime=10 # Make packets pass firewall only once when using dummynet # i.e. packets going thru pipe are passing out from firewall with accept #net.inet.ip.fw.one_pass=1 # shm_use_phys Wires all shared pages, making them unswappable # Use this to lessen Virtual Memory Manager's work when using Shared Mem. # Useful for databases #kern.ipc.shm_use_phys=1 # ZFS # Enable prefetch. Useful for sequential load type i.e fileserver. # FreeBSD sets vfs.zfs.prefetch_disable to 1 on any i386 systems and # on any amd64 systems with less than 4GB of avaiable memory # For additional info check this nabble thread http://old.nabble.com/Samba-read-speed-performance-tuning-td27964534.html #vfs.zfs.prefetch_disable=0 # On highload servers you may notice following message in dmesg: # "Approaching the limit on PV entries, consider increasing either the # vm.pmap.shpgperproc or the vm.pmap.pv_entry_max tunable" vm.pmap.shpgperproc=2048 loader.conf: # Accept filters for data, http and DNS requests # Useful when your software uses select() instead of kevent/kqueue or when you under DDoS # DNS accf available on 8.0+ accf_data_load="YES" accf_http_load="YES" accf_dns_load="YES" # Async IO system calls aio_load="YES" # Linux specific devices in /dev # As for 8.1 it only /dev/full #lindev_load="YES" # Adds NCQ support in FreeBSD # WARNING! all ad[0-9]+ devices will be renamed to ada[0-9]+ # 8.0+ only #ahci_load="YES" #siis_load="YES" # FreeBSD 8.2+ # New Congestion Control for FreeBSD # http://caia.swin.edu.au/urp/newtcp/tools/cc_chd-readme-0.1.txt # http://www.ietf.org/proceedings/78/slides/iccrg-5.pdf # Initial merge commit message http://www.mail-archive.com/[email protected]/msg31410.html #cc_chd_load="YES" # Increase kernel memory size to 3G. # # Use ONLY if you have KVA_PAGES in kernel configuration, and you have more than 3G RAM # Otherwise panic will happen on next reboot! # # It's required for high buffer sizes: kern.ipc.nmbjumbop, kern.ipc.nmbclusters, etc # Useful on highload stateful firewalls, proxies or ZFS fileservers # (FreeBSD 7.2+ amd64 users: Check that current value is lower!) #vm.kmem_size="3G" # If your server has lots of swap (>4Gb) you should increase following value # according to http://lists.freebsd.org/pipermail/freebsd-hackers/2009-October/029616.html # Otherwise you'll be getting errors # "kernel: swap zone exhausted, increase kern.maxswzone" # kern.maxswzone="256M" # Older versions of FreeBSD can't tune maxfiles on the fly #kern.maxfiles="200000" # Useful for databases # Sets maximum data size to 1G # (FreeBSD 7.2+ amd64 users: Check that current value is lower!) #kern.maxdsiz="1G" # Maximum buffer size(vfs.maxbufspace) # You can check current one via vfs.bufspace # Should be lowered/upped depending on server's load-type # Usually decreased to preserve kmem # (default is 10% of mem) #kern.maxbcache="512M" # Sendfile buffers # For i386 only #kern.ipc.nsfbufs=10240 # FreeBSD 9+ # HPET "legacy route" support. It should allow HPET to work per-CPU # See http://www.mail-archive.com/[email protected]/msg03603.html #hint.atrtc.0.clock=0 #hint.attimer.0.clock=0 #hint.hpet.0.legacy_route=1 # syncache Hash table tuning net.inet.tcp.syncache.hashsize=1024 net.inet.tcp.syncache.bucketlimit=512 net.inet.tcp.syncache.cachelimit=65536 # Increased hostcache # Later host cache can be viewed via net.inet.tcp.hostcache.list hidden sysctl # Very useful for it's RTT RTTVAR # Must be power of two net.inet.tcp.hostcache.hashsize=65536 # hashsize * bucketlimit (which is 30 by default) # It allocates 255Mb (1966080*136) of RAM net.inet.tcp.hostcache.cachelimit=1966080 # TCP control-block Hash table tuning net.inet.tcp.tcbhashsize=4096 # Disable ipfw deny all # Should be uncommented when there is a chance that # kernel and ipfw binary may be out-of sync on next reboot #net.inet.ip.fw.default_to_accept=1 # # SIFTR (Statistical Information For TCP Research) is a kernel module that # logs a range of statistics on active TCP connections to a log file. # See prerelease notes http://groups.google.com/group/mailing.freebsd.current/browse_thread/thread/b4c18be6cdce76e4 # and man 4 sitfr #siftr_load="YES" # Enable superpages, for 7.2+ only # Also read http://lists.freebsd.org/pipermail/freebsd-hackers/2009-November/030094.html vm.pmap.pg_ps_enabled=1 # Usefull if you are using Intel-Gigabit NIC #hw.em.rxd=4096 #hw.em.txd=4096 #hw.em.rx_process_limit="-1" # Also if you have ALOT interrupts on NIC - play with following parameters # NOTE: You should set them for every NIC #dev.em.0.rx_int_delay: 250 #dev.em.0.tx_int_delay: 250 #dev.em.0.rx_abs_int_delay: 250 #dev.em.0.tx_abs_int_delay: 250 # There is also multithreaded version of em/igb drivers can be found here: # http://people.yandex-team.ru/~wawa/ # # for additional em monitoring and statistics use # sysctl dev.em.0.stats=1 ; dmesg # sysctl dev.em.0.debug=1 ; dmesg # Also after r209242 (-CURRENT) there is a separate sysctl for each stat variable; # Same tunings for igb #hw.igb.rxd=4096 #hw.igb.txd=4096 #hw.igb.rx_process_limit=100 # Some useful netisr tunables. See sysctl net.isr #net.isr.maxthreads=4 #net.isr.defaultqlimit=4096 #net.isr.maxqlimit: 10240 # Bind netisr threads to CPUs #net.isr.bindthreads=1 # # FreeBSD 9.x+ # Increase interface send queue length # See commit message http://svn.freebsd.org/viewvc/base?view=revision&revision=207554 #net.link.ifqmaxlen=1024 # Nicer boot logo =) loader_logo="beastie" And finally here is KERNCONF: # Just some of them, see also # cat /sys/{i386,amd64,}/conf/NOTES # This one useful only on i386 #options KVA_PAGES=512 # You can play with HZ in environments with high interrupt rate (default is 1000) # 100 is for my notebook to prolong it's battery life #options HZ=100 # Polling is goot on network loads with high packet rates and low-end NICs # NB! Do not enable it if you want more than one netisr thread #options DEVICE_POLLING # Eliminate datacopy on socket read-write # To take advantage with zero copy sockets you should have an MTU >= 4k # This req. is only for receiving data. # Read more in man zero_copy_sockets # Also this epic thread on kernel trap: # http://kerneltrap.org/node/6506 # Here Linus says that "anybody that does it that way (FreeBSD) is totally incompetent" #options ZERO_COPY_SOCKETS # Support TCP sign. Used for IPSec options TCP_SIGNATURE # There was stackoverflow found in KAME IPSec stack: # See http://secunia.com/advisories/43995/ # For quick workaround you can use `ipfw add deny proto ipcomp` options IPSEC # This ones can be loaded as modules. They described in loader.conf section #options ACCEPT_FILTER_DATA #options ACCEPT_FILTER_HTTP # Adding ipfw, also can be loaded as modules options IPFIREWALL # On 8.1+ you can disable verbose to see blocked packets on ipfw0 interface. # Also there is no point in compiling verbose into the kernel, because # now there is net.inet.ip.fw.verbose tunable. #options IPFIREWALL_VERBOSE #options IPFIREWALL_VERBOSE_LIMIT=10 options IPFIREWALL_FORWARD # Adding kernel NAT options IPFIREWALL_NAT options LIBALIAS # Traffic shaping options DUMMYNET # Divert, i.e. for userspace NAT options IPDIVERT # This is for OpenBSD's pf firewall device pf device pflog # pf's QoS - ALTQ options ALTQ options ALTQ_CBQ # Class Bases Queuing (CBQ) options ALTQ_RED # Random Early Detection (RED) options ALTQ_RIO # RED In/Out options ALTQ_HFSC # Hierarchical Packet Scheduler (HFSC) options ALTQ_PRIQ # Priority Queuing (PRIQ) options ALTQ_NOPCC # Required for SMP build # Pretty console # Manual can be found here http://forums.freebsd.org/showthread.php?t=6134 #options VESA #options SC_PIXEL_MODE # Disable reboot on Ctrl Alt Del #options SC_DISABLE_REBOOT # Change normal|kernel messages color options SC_NORM_ATTR=(FG_GREEN|BG_BLACK) options SC_KERNEL_CONS_ATTR=(FG_YELLOW|BG_BLACK) # More scroll space options SC_HISTORY_SIZE=8192 # Adding hardware crypto device device crypto device cryptodev # Useful network interfaces device vlan device tap #Virtual Ethernet driver device gre #IP over IP tunneling device if_bridge #Bridge interface device pfsync #synchronization interface for PF device carp #Common Address Redundancy Protocol device enc #IPsec interface device lagg #Link aggregation interface device stf #IPv4-IPv6 port # Also for my notebook, but may be used with Opteron device amdtemp # Same for Intel processors device coretemp # man 4 cpuctl device cpuctl # CPU control pseudo-device # Support for ECMP. More than one route for destination # Works even with default route so one can use it as LB for two ISP # For now code is unstable and panics (panic: rtfree 2) on route deletions. #options RADIX_MPATH # Multicast routing #options MROUTING #options PIM # Debug & DTrace options KDB # Kernel debugger related code options KDB_TRACE # Print a stack trace for a panic options KDTRACE_FRAME # amd64-only(?) options KDTRACE_HOOKS # all architectures - enable general DTrace hooks #options DDB #options DDB_CTF # all architectures - kernel ELF linker loads CTF data # Adaptive spining in lockmgr (8.x+) # See http://www.mail-archive.com/[email protected]/msg10782.html options ADAPTIVE_LOCKMGRS # UTF-8 in console (8.x+) #options TEKEN_UTF8 # FreeBSD 8.1+ # Deadlock resolver thread # For additional information see http://www.mail-archive.com/[email protected]/msg18124.html # (FYI: "resolution" is panic so use with caution) #options DEADLKRES # Increase maximum size of Raw I/O and sendfile(2) readahead #options MAXPHYS=(1024*1024) #options MAXBSIZE=(1024*1024) # For scheduler debug enable following option. # Debug will be available via `kern.sched.stats` sysctl # For more information see http://svnweb.freebsd.org/base/head/sys/conf/NOTES?view=markup #options SCHED_STATS If you are tuning network for maximum performance you may wish to play with ifconfig options like: # You can list all capabilities via `ifconfig -m` ifconfig [-]rxcsum [-]txcsum [-]tso [-]lro mtu In case you've enabled DDB in kernel config, you should edit your /etc/ddb.conf and add something like this to enable automatic reboot (and textdump as bonus): script kdb.enter.panic=textdump set; capture on; show pcpu; bt; ps; alltrace; capture off; call doadump; reset script kdb.enter.default=textdump set; capture on; bt; ps; capture off; call doadump; reset And do not forget to add ddb_enable="YES" to /etc/rc.conf Since FreeBSD 9 you can select to enable/disable flowcontrol on your NIC: # See http://en.wikipedia.org/wiki/Ethernet_flow_control and # http://www.mail-archive.com/[email protected]/msg07927.html for additional info ifconfig bge0 media auto mediaopt flowcontrol PS. Also most of FreeBSD's limits can be monitored by # vmstat -z and # limits PPS. variety of network counters can be monitored via # netstat -s In FreeBSD-9 netstat's -Q option appeared, try following command to display netisr stats # netstat -Q PPPS. also see # man 7 tuning PPPPS. I wanted to thank FreeBSD community, especially author of nginx - Igor Sysoev, nginx-ru@ and FreeBSD-performance@ mailing lists for providing useful information about FreeBSD tuning. FreeBSD WIP * Whats cooking for FreeBSD 7? * Whats cooking for FreeBSD 8? * Whats cooking for FreeBSD 9? So here is the question: What tunings are you using on yours FreeBSD servers? You can also post your /etc/sysctl.conf, /boot/loader.conf, kernel options, etc with description of its' meaning (do not copy-paste from sysctl -d). Don't forget to specify server type (web, smb, gateway, etc) Let's share experience!

Read the article

Error 2013: Lost connection to MySQL server during query when executing CHECK TABLE FOR UPGRADE

- by Dean Richardson

I just upgraded Ubuntu from 11.10 to 12.04. My rails app now returns the (passenger) error "Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (111) (Mysql2::Error)". I get a similar error when I try to access mysql at the command line on my Ubuntu server using mysql -u root -p. I have mysql-server 5.5 installed. I've checked and mysql is not running. When I try to restart it, it fails. Here are some key lines from the tail of /var/log/syslog after an attempted restart: dean@dgwjasonfried:/etc/mysql$ tail -f /var/log/syslog Mar 7 08:55:27 dgwjasonfried /etc/mysql/debian-start[5107]: Looking for 'mysqlcheck' as: /usr/bin/mysqlcheck Mar 7 08:55:27 dgwjasonfried /etc/mysql/debian-start[5107]: Running 'mysqlcheck' with connection arguments: '--port=3306' '--socket=/var/run/mysqld/mysqld.sock' '--host=localhost' '--socket=/var/run/mysqld/mysqld.sock' '--host=localhost' '--socket=/var/run/mysqld/mysqld.sock' Mar 7 08:55:27 dgwjasonfried /etc/mysql/debian-start[5107]: Running 'mysqlcheck' with connection arguments: '--port=3306' '--socket=/var/run/mysqld/mysqld.sock' '--host=localhost' '--socket=/var/run/mysqld/mysqld.sock' '--host=localhost' '--socket=/var/run/mysqld/mysqld.sock' Mar 7 08:55:27 dgwjasonfried /etc/mysql/debian-start[5107]: /usr/bin/mysqlcheck: Got error: 2013: Lost connection to MySQL server during query when executing 'CHECK TABLE ... FOR UPGRADE' Mar 7 08:55:27 dgwjasonfried /etc/mysql/debian-start[5107]: FATAL ERROR: Upgrade failed Mar 7 08:55:27 dgwjasonfried /etc/mysql/debian-start[5107]: molex_app_development.assets OK Mar 7 08:55:27 dgwjasonfried /etc/mysql/debian-start[5107]: molex_app_development.ecd_types OK Mar 7 08:55:27 dgwjasonfried /etc/mysql/debian-start[5124]: Checking for insecure root accounts. Mar 7 08:55:27 dgwjasonfried kernel: [ 7551.769657] init: mysql main process (5064) terminated with status 1 Mar 7 08:55:27 dgwjasonfried kernel: [ 7551.769697] init: mysql respawning too fast, stopped Here is most of /etc/mysql/my.cnf: Remember to edit /etc/mysql/debian.cnf when changing the socket location. [client] port = 3306 socket = /var/run/mysqld/mysqld.sock Here is entries for some specific programs The following values assume you have at least 32M ram This was formally known as [safe_mysqld]. Both versions are currently parsed. [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] Basic Settings user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp lc-messages-dir = /usr/share/mysql skip-external-locking Instead of skip-networking the default is now to listen only on localhost which is more compatible and is not less secure. bind-address = 127.0.0.1 And here are permissions for var/run/mysqld/mysqld.sock: srwxrwxrwx 1 mysql mysql 0 Mar 7 09:18 mysqld.sock I'd be grateful for any suggestions the community might have. I reviewed the related questions here and attempted some of the fixes offered but to no avail. Thanks! Dean Richardson Update: Thanks to quanta's suggestion, I looked at the /var/log/mysql/error.log file. I found error messages relating to pointers, fatal signals, and more stuff that I really couldn't make much sense of. I also found mysql man page references, however. One suggested that I try starting mysqld with the --innodb_force_recovery=# option, then attempt to dump (or drop) the offending/corrupted database or table. I worked through the escalating option levels one-by-one (innodb_force_recovery=1, innodb_force_recovery=2, etc.) This allowed me to successfully run mysql -u root -p from the command line and execute several commands. I was able to run queries on my production database, but any attempt to query, dump, or even drop my development database raised an error and led to me losing the connection to mysql. So I've made progress, but until I'm somehow able to drop or repair my development db I'm still unable to get my app to load. Any further advice or suggestions? Thanks! Dean Update: Right after running sudo mysqld --innodb_force_recover=1 from the command line, the error.log contains this: Right after retrying sudo mysqld --innodb_force_recover=1, The error.log file shows this: 130308 4:55:39 [Note] Plugin 'FEDERATED' is disabled. 130308 4:55:39 InnoDB: The InnoDB memory heap is disabled 130308 4:55:39 InnoDB: Mutexes and rw_locks use GCC atomic builtins 130308 4:55:39 InnoDB: Compressed tables use zlib 1.2.3.4 130308 4:55:39 InnoDB: Initializing buffer pool, size = 128.0M 130308 4:55:39 InnoDB: Completed initialization of buffer pool 130308 4:55:39 InnoDB: highest supported file format is Barracuda. InnoDB: The log sequence number in ibdata files does not match InnoDB: the log sequence number in the ib_logfiles! 130308 4:55:39 InnoDB: Database was not shut down normally! InnoDB: Starting crash recovery. InnoDB: Reading tablespace information from the .ibd files... InnoDB: Restoring possible half-written data pages from the doublewrite InnoDB: buffer... 130308 4:55:40 InnoDB: Waiting for the background threads to start 130308 4:55:41 InnoDB: 1.1.8 started; log sequence number 10259220 130308 4:55:41 InnoDB: !!! innodb_force_recovery is set to 1 !!! 130308 4:55:41 [Note] Server hostname (bind-address): '127.0.0.1'; port: 3306 130308 4:55:41 [Note] - '127.0.0.1' resolves to '127.0.0.1'; 130308 4:55:41 [Note] Server socket created on IP: '127.0.0.1'. 130308 4:55:41 [Note] Event Scheduler: Loaded 0 events 130308 4:55:41 [Note] mysqld: ready for connections. Version: '5.5.29-0ubuntu0.12.04.2' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu) Then after mysql -u root -p and mysql> drop database molex_app_development; ERROR 2013 (HY000): Lost connection to MySQL server during query mysql> the error.log contains: dean@dgwjasonfried:/var/log/mysql$ tail -f error.log /lib/x86_64-linux-gnu/libc.so.6(clone+0x6d)[0x7f6a3ff9ecbd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort. Query (7f6a1c004bd8): is an invalid pointer Connection ID (thread ID): 1 Status: NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash. 130308 4:55:39 [Note] Plugin 'FEDERATED' is disabled. 130308 4:55:39 InnoDB: The InnoDB memory heap is disabled 130308 4:55:39 InnoDB: Mutexes and rw_locks use GCC atomic builtins 130308 4:55:39 InnoDB: Compressed tables use zlib 1.2.3.4 130308 4:55:39 InnoDB: Initializing buffer pool, size = 128.0M 130308 4:55:39 InnoDB: Completed initialization of buffer pool 130308 4:55:39 InnoDB: highest supported file format is Barracuda. InnoDB: The log sequence number in ibdata files does not match InnoDB: the log sequence number in the ib_logfiles! 130308 4:55:39 InnoDB: Database was not shut down normally! InnoDB: Starting crash recovery. InnoDB: Reading tablespace information from the .ibd files... InnoDB: Restoring possible half-written data pages from the doublewrite InnoDB: buffer... 130308 4:55:40 InnoDB: Waiting for the background threads to start 130308 4:55:41 InnoDB: 1.1.8 started; log sequence number 10259220 130308 4:55:41 InnoDB: !!! innodb_force_recovery is set to 1 !!! 130308 4:55:41 [Note] Server hostname (bind-address): '127.0.0.1'; port: 3306 130308 4:55:41 [Note] - '127.0.0.1' resolves to '127.0.0.1'; 130308 4:55:41 [Note] Server socket created on IP: '127.0.0.1'. 130308 4:55:41 [Note] Event Scheduler: Loaded 0 events 130308 4:55:41 [Note] mysqld: ready for connections. Version: '5.5.29-0ubuntu0.12.04.2' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu) 130308 4:58:23 [ERROR] Incorrect definition of table mysql.proc: expected column 'comment' at position 15 to have type text, found type char(64). 130308 4:58:23 InnoDB: Assertion failure in thread 140168992810752 in file fsp0fsp.c line 3639 InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/refman/5.5/en/forcing-innodb-recovery.html InnoDB: about forcing recovery. 10:58:23 UTC - mysqld got signal 6 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=1 max_threads=151 thread_count=1 connection_count=1 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 346681 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. Thread pointer: 0x7f7ba4f6c2f0 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 7f7ba3065e60 thread_stack 0x30000 mysqld(my_print_stacktrace+0x29)[0x7f7ba3609039] mysqld(handle_fatal_signal+0x483)[0x7f7ba34cf9c3] /lib/x86_64-linux-gnu/libpthread.so.0(+0xfcb0)[0x7f7ba2220cb0] /lib/x86_64-linux-gnu/libc.so.6(gsignal+0x35)[0x7f7ba188c425] /lib/x86_64-linux-gnu/libc.so.6(abort+0x17b)[0x7f7ba188fb8b] mysqld(+0x65e0fc)[0x7f7ba37160fc] mysqld(+0x602be6)[0x7f7ba36babe6] mysqld(+0x635006)[0x7f7ba36ed006] mysqld(+0x5d7072)[0x7f7ba368f072] mysqld(+0x5d7b9c)[0x7f7ba368fb9c] mysqld(+0x6a3348)[0x7f7ba375b348] mysqld(+0x6a3887)[0x7f7ba375b887] mysqld(+0x5c6a86)[0x7f7ba367ea86] mysqld(+0x5ae3a7)[0x7f7ba36663a7] mysqld(_Z15ha_delete_tableP3THDP10handlertonPKcS4_S4_b+0x16d)[0x7f7ba34d3ffd] mysqld(_Z23mysql_rm_table_no_locksP3THDP10TABLE_LISTbbbb+0x568)[0x7f7ba3417f78] mysqld(_Z11mysql_rm_dbP3THDPcbb+0x8aa)[0x7f7ba339780a] mysqld(_Z21mysql_execute_commandP3THD+0x394c)[0x7f7ba33b886c] mysqld(_Z11mysql_parseP3THDPcjP12Parser_state+0x10f)[0x7f7ba33bb28f] mysqld(_Z16dispatch_command19enum_server_commandP3THDPcj+0x1380)[0x7f7ba33bc6e0] mysqld(_Z24do_handle_one_connectionP3THD+0x1bd)[0x7f7ba346119d] mysqld(handle_one_connection+0x50)[0x7f7ba3461200] /lib/x86_64-linux-gnu/libpthread.so.0(+0x7e9a)[0x7f7ba2218e9a] /lib/x86_64-linux-gnu/libc.so.6(clone+0x6d)[0x7f7ba1949cbd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort. Query (7f7b7c004b60): is an invalid pointer Connection ID (thread ID): 1 Status: NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash. --Dean

Read the article

DHCP settings out of range Internet shuts off after a few minutes

- by user263115

I recently upgraded from windows eight to windows 8.1 I do not know if this has anything to do with anything I have a 64 bit OS. My Internet goes off by itself every 5 minutes even though my wireless icon at the lower right of the screen still shows connected I had an error message in the last event in it said that might DHCP settings were out of range. I get my internet at my house through a wireless portable hotspot through my smart phone. But i haven't ever had any problems before and i only have this problem on this network. If i turn airplane mode on and reset my network card, the internet will come back to life but soon die. i don't experience this problem while on a different network or if i'm on WiFi. This s really annoying please help Windows IP Configuration Host Name . . . . . . . . . . . . : NastyMcnastyJr Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : TeamViewer VPN Adapter Physical Address. . . . . . . . . : 00-FF-5D-13-26-21 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Wireless LAN adapter Local Area Connection* 11: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Wi-Fi Direct Virtual Adapter Physical Address. . . . . . . . . : F6-B7-E2-50-09-38 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Wireless LAN adapter SAMMY McNASTY: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom 802.11n Network Adapter Physical Address. . . . . . . . . : F4-B7-E2-50-09-38 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::3107:66bc:cf1f:c776%4(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.43.3(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Friday, November 1, 2013 9:50:20 PM Lease Expires . . . . . . . . . . : Saturday, November 2, 2013 12:56:46 AM Default Gateway . . . . . . . . . : 192.168.43.1 DHCP Server . . . . . . . . . . . : 192.168.43.1 DHCPv6 IAID . . . . . . . . . . . : 83146722 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-19-F1-98-B4-20-89-84-84-61-BB DNS Servers . . . . . . . . . . . : 192.168.43.1 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter Ethernet: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetLink (TM) Gigabit Ethernet Physical Address. . . . . . . . . : 20-89-84-84-61-BB DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Log Name: System Source: Microsoft-Windows-UserPnp Date: 10/26/2013 7:52:23 PM Event ID: 20003 Task Category: (7005) Level: Information Keywords: User: SYSTEM Computer: NastyMcnastyJr Description: Driver Management has concluded the process to add Service vwifibus for Device Instance ID PCI\VEN_14E4&DEV_4727&SUBSYS_E042105B&REV_01\4&3265ADAB&0&00E1 with the following status: 0. Event Xml: 20003 0 4 7005 0 0x8000000000000000 5118 System NastyMcnastyJr vwifibus \SystemRoot\system32\DRIVERS\vwifibus.sys PCI\VEN_14E4&DEV_4727&SUBSYS_E042105B&REV_01\4&3265ADAB&0&00E1 false true 0 Log Name: System Source: Microsoft-Windows-UserPnp Date: 10/19/2013 3:29:12 PM Event ID: 20001 Task Category: (7005) Level: Information Keywords: User: SYSTEM Computer: NastyMcnastyJr Description: Driver Management concluded the process to install driver netbc64.inf_amd64_0df63b5297d0f820\netbc64.inf for Device Instance ID PCI\VEN_14E4&DEV_4727&SUBSYS_E042105B&REV_01\4&3265ADAB&0&00E1 with the following status: 0x0. Event Xml: 20001 0 4 7005 0 0x8000000000000000 2015 System NastyMcnastyJr netbc64.inf_amd64_0df63b5297d0f820\netbc64.inf 6.30.223.102 Microsoft PCI\VEN_14E4&DEV_4727&SUBSYS_E042105B&REV_01\4&3265ADAB&0&00E1 {4D36E972-E325-11CE-BFC1-08002BE10318} false false false 0x0 Broadcom 802.11n Network Adapter Log Name: System Source: Microsoft-Windows-DNS-Client Date: 11/2/2013 12:24:59 AM Event ID: 1014 Task Category: (1014) Level: Warning Keywords: (268435456) User: NETWORK SERVICE Computer: NastyMcnastyJr Description: Name resolution for the name www.google.com timed out after none of the configured DNS servers responded. Event Xml: 1014 0 3 1014 0 0x4000000010000000 34771 System NastyMcnastyJr www.google.com 128 02000000C0A82B01000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000

Read the article

OpenVPN - Windows 8 to Windows 2008 Server, not connecting

- by niico

I have followed this tutorial about setting up an OpenVPN Server on Windows Server - and a client on Windows (in this case Windows 8). The server appears to be running fine - but it is not connecting with this error: Mon Jul 22 19:09:04 2013 Warning: cannot open --log file: C:\Program Files\OpenVPN\log\my-laptop.log: Access is denied. (errno=5) Mon Jul 22 19:09:04 2013 OpenVPN 2.3.2 x86_64-w64-mingw32 [SSL (OpenSSL)] [LZO] [PKCS11] [eurephia] [IPv6] built on Jun 3 2013 Mon Jul 22 19:09:04 2013 MANAGEMENT: TCP Socket listening on [AF_INET]127.0.0.1:25340 Mon Jul 22 19:09:04 2013 Need hold release from management interface, waiting... Mon Jul 22 19:09:05 2013 MANAGEMENT: Client connected from [AF_INET]127.0.0.1:25340 Mon Jul 22 19:09:05 2013 MANAGEMENT: CMD 'state on' Mon Jul 22 19:09:05 2013 MANAGEMENT: CMD 'log all on' Mon Jul 22 19:09:05 2013 MANAGEMENT: CMD 'hold off' Mon Jul 22 19:09:05 2013 MANAGEMENT: CMD 'hold release' Mon Jul 22 19:09:05 2013 Socket Buffers: R=[65536->65536] S=[65536->65536] Mon Jul 22 19:09:05 2013 UDPv4 link local: [undef] Mon Jul 22 19:09:05 2013 UDPv4 link remote: [AF_INET]66.666.66.666:9999 Mon Jul 22 19:09:05 2013 MANAGEMENT: >STATE:1374494945,WAIT,,, Mon Jul 22 19:10:05 2013 TLS Error: TLS key negotiation failed to occur within 60 seconds (check your network connectivity) Mon Jul 22 19:10:05 2013 TLS Error: TLS handshake failed Mon Jul 22 19:10:05 2013 SIGUSR1[soft,tls-error] received, process restarting Mon Jul 22 19:10:05 2013 MANAGEMENT: >STATE:1374495005,RECONNECTING,tls-error,, Mon Jul 22 19:10:05 2013 Restart pause, 2 second(s) Note I have changed the IP and port no (it uses a non-standard port for security reasons). That port is open on the hardware firewall. The server logs are showing a connection attempt from my client: TLS: Initial packet from [AF_INET]118.68.xx.xx:65011, sid=081af4ed xxxxxxxx Mon Jul 22 14:19:15 2013 118.68.xx.xx:65011 TLS Error: TLS key negotiation failed to occur within 60 seconds (check your network connectivity) How can I problem solve this & find the problem? Thx Update - Client config file: ############################################## # Sample client-side OpenVPN 2.0 config file # # for connecting to multi-client server. # # # # This configuration can be used by multiple # # clients, however each client should have # # its own cert and key files. # # # # On Windows, you might want to rename this # # file so it has a .ovpn extension # ############################################## # Specify that we are a client and that we # will be pulling certain config file directives # from the server. client # Use the same setting as you are using on # the server. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. ;dev tap dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel # if you have more than one. On XP SP2, # you may need to disable the firewall # for the TAP adapter. ;dev-node MyTap # Are we connecting to a TCP or # UDP server? Use the same setting as # on the server. ;proto tcp proto udp # The hostname/IP and port of the server. # You can have multiple remote entries # to load balance between the servers. remote 00.00.00.00 1194 ;remote 00.00.00.00 9999 ;remote my-server-2 1194 # Choose a random host from the remote # list for load-balancing. Otherwise # try hosts in the order specified. ;remote-random # Keep trying indefinitely to resolve the # host name of the OpenVPN server. Very useful # on machines which are not permanently connected # to the internet such as laptops. resolv-retry infinite # Most clients don't need to bind to # a specific local port number. nobind # Downgrade privileges after initialization (non-Windows only) ;user nobody ;group nobody # Try to preserve some state across restarts. persist-key persist-tun # If you are connecting through an # HTTP proxy to reach the actual OpenVPN # server, put the proxy server/IP and # port number here. See the man page # if your proxy server requires # authentication. ;http-proxy-retry # retry on connection failures ;http-proxy [proxy server] [proxy port #] # Wireless networks often produce a lot # of duplicate packets. Set this flag # to silence duplicate packet warnings. ;mute-replay-warnings # SSL/TLS parms. # See the server config file for more # description. It's best to use # a separate .crt/.key file pair # for each client. A single ca # file can be used for all clients. ca "C:\\Program Files\\OpenVPN\\config\\ca.crt" cert "C:\\Program Files\\OpenVPN\\config\\my-laptop.crt" key "C:\\Program Files\\OpenVPN\\config\\my-laptop.key" # Verify server certificate by checking # that the certicate has the nsCertType # field set to "server". This is an # important precaution to protect against # a potential attack discussed here: # http://openvpn.net/howto.html#mitm # # To use this feature, you will need to generate # your server certificates with the nsCertType # field set to "server". The build-key-server # script in the easy-rsa folder will do this. ns-cert-type server # If a tls-auth key is used on the server # then every client must also have the key. ;tls-auth ta.key 1 # Select a cryptographic cipher. # If the cipher option is used on the server # then you must also specify it here. ;cipher x # Enable compression on the VPN link. # Don't enable this unless it is also # enabled in the server config file. comp-lzo # Set log file verbosity. verb 3 # Silence repeating messages ;mute 20 Server config file: ################################################# # Sample OpenVPN 2.0 config file for # # multi-client server. # # # # This file is for the server side # # of a many-clients <-> one-server # # OpenVPN configuration. # # # # OpenVPN also supports # # single-machine <-> single-machine # # configurations (See the Examples page # # on the web site for more info). # # # # This config should work on Windows # # or Linux/BSD systems. Remember on # # Windows to quote pathnames and use # # double backslashes, e.g.: # # "C:\\Program Files\\OpenVPN\\config\\foo.key" # # # # Comments are preceded with '#' or ';' # ################################################# # Which local IP address should OpenVPN # listen on? (optional) ;local 00.00.00.00 # Which TCP/UDP port should OpenVPN listen on? # If you want to run multiple OpenVPN instances # on the same machine, use a different port # number for each one. You will need to # open up this port on your firewall. std 1194 port 1194 # TCP or UDP server? ;proto tcp proto udp # "dev tun" will create a routed IP tunnel, # "dev tap" will create an ethernet tunnel. # Use "dev tap0" if you are ethernet bridging # and have precreated a tap0 virtual interface # and bridged it with your ethernet interface. # If you want to control access policies # over the VPN, you must create firewall # rules for the the TUN/TAP interface. # On non-Windows systems, you can give # an explicit unit number, such as tun0. # On Windows, use "dev-node" for this. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. ;dev tap dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel if you # have more than one. On XP SP2 or higher, # you may need to selectively disable the # Windows firewall for the TAP adapter. # Non-Windows systems usually don't need this. ;dev-node MyTap # SSL/TLS root certificate (ca), certificate # (cert), and private key (key). Each client # and the server must have their own cert and # key file. The server and all clients will # use the same ca file. # # See the "easy-rsa" directory for a series # of scripts for generating RSA certificates # and private keys. Remember to use # a unique Common Name for the server # and each of the client certificates. # # Any X509 key management system can be used. # OpenVPN can also use a PKCS #12 formatted key file # (see "pkcs12" directive in man page). ca "C:\\Program Files\\OpenVPN\\config\\ca.crt" cert "C:\\Program Files\\OpenVPN\\config\\server.crt" key "C:\\Program Files\\OpenVPN\\config\\server.key" # Diffie hellman parameters. # Generate your own with: # openssl dhparam -out dh1024.pem 1024 # Substitute 2048 for 1024 if you are using # 2048 bit keys. dh "C:\\Program Files\\OpenVPN\\config\\dh2048.pem" # Configure server mode and supply a VPN subnet # for OpenVPN to draw client addresses from. # The server will take 10.8.0.1 for itself, # the rest will be made available to clients. # Each client will be able to reach the server # on 10.8.0.1. Comment this line out if you are # ethernet bridging. See the man page for more info. server 10.8.0.0 255.255.255.0 # Maintain a record of client <-> virtual IP address # associations in this file. If OpenVPN goes down or # is restarted, reconnecting clients can be assigned # the same virtual IP address from the pool that was # previously assigned. ifconfig-pool-persist ipp.txt # Configure server mode for ethernet bridging. # You must first use your OS's bridging capability # to bridge the TAP interface with the ethernet # NIC interface. Then you must manually set the # IP/netmask on the bridge interface, here we # assume 10.8.0.4/255.255.255.0. Finally we # must set aside an IP range in this subnet # (start=10.8.0.50 end=10.8.0.100) to allocate # to connecting clients. Leave this line commented # out unless you are ethernet bridging. ;server-bridge 10.8.0.4 255.255.255.0 10.8.0.50 10.8.0.100 # Configure server mode for ethernet bridging # using a DHCP-proxy, where clients talk # to the OpenVPN server-side DHCP server # to receive their IP address allocation # and DNS server addresses. You must first use # your OS's bridging capability to bridge the TAP # interface with the ethernet NIC interface. # Note: this mode only works on clients (such as # Windows), where the client-side TAP adapter is # bound to a DHCP client. ;server-bridge # Push routes to the client to allow it # to reach other private subnets behind # the server. Remember that these # private subnets will also need # to know to route the OpenVPN client # address pool (10.8.0.0/255.255.255.0) # back to the OpenVPN server. ;push "route 192.168.10.0 255.255.255.0" ;push "route 192.168.20.0 255.255.255.0" # To assign specific IP addresses to specific # clients or if a connecting client has a private # subnet behind it that should also have VPN access, # use the subdirectory "ccd" for client-specific # configuration files (see man page for more info). # EXAMPLE: Suppose the client # having the certificate common name "Thelonious" # also has a small subnet behind his connecting # machine, such as 192.168.40.128/255.255.255.248. # First, uncomment out these lines: ;client-config-dir ccd ;route 192.168.40.128 255.255.255.248 # Then create a file ccd/Thelonious with this line: # iroute 192.168.40.128 255.255.255.248 # This will allow Thelonious' private subnet to # access the VPN. This example will only work # if you are routing, not bridging, i.e. you are # using "dev tun" and "server" directives. # EXAMPLE: Suppose you want to give # Thelonious a fixed VPN IP address of 10.9.0.1. # First uncomment out these lines: ;client-config-dir ccd ;route 10.9.0.0 255.255.255.252 # Then add this line to ccd/Thelonious: # ifconfig-push 10.9.0.1 10.9.0.2 # Suppose that you want to enable different # firewall access policies for different groups # of clients. There are two methods: # (1) Run multiple OpenVPN daemons, one for each # group, and firewall the TUN/TAP interface # for each group/daemon appropriately. # (2) (Advanced) Create a script to dynamically # modify the firewall in response to access # from different clients. See man # page for more info on learn-address script. ;learn-address ./script # If enabled, this directive will configure # all clients to redirect their default # network gateway through the VPN, causing # all IP traffic such as web browsing and # and DNS lookups to go through the VPN # (The OpenVPN server machine may need to NAT # or bridge the TUN/TAP interface to the internet # in order for this to work properly). ;push "redirect-gateway def1 bypass-dhcp" # Certain Windows-specific network settings # can be pushed to clients, such as DNS # or WINS server addresses. CAVEAT: # http://openvpn.net/faq.html#dhcpcaveats # The addresses below refer to the public # DNS servers provided by opendns.com. ;push "dhcp-option DNS 208.67.222.222" ;push "dhcp-option DNS 208.67.220.220" # Uncomment this directive to allow differenta # clients to be able to "see" each other. # By default, clients will only see the server. # To force clients to only see the server, you # will also need to appropriately firewall the # server's TUN/TAP interface. ;client-to-client # Uncomment this directive if multiple clients # might connect with the same certificate/key # files or common names. This is recommended # only for testing purposes. For production use, # each client should have its own certificate/key # pair. # # IF YOU HAVE NOT GENERATED INDIVIDUAL # CERTIFICATE/KEY PAIRS FOR EACH CLIENT, # EACH HAVING ITS OWN UNIQUE "COMMON NAME", # UNCOMMENT THIS LINE OUT. ;duplicate-cn # The keepalive directive causes ping-like # messages to be sent back and forth over # the link so that each side knows when # the other side has gone down. # Ping every 10 seconds, assume that remote # peer is down if no ping received during # a 120 second time period. keepalive 10 120 # For extra security beyond that provided # by SSL/TLS, create an "HMAC firewall" # to help block DoS attacks and UDP port flooding. # # Generate with: # openvpn --genkey --secret ta.key # # The server and each client must have # a copy of this key. # The second parameter should be '0' # on the server and '1' on the clients. ;tls-auth ta.key 0 # This file is secret # Select a cryptographic cipher. # This config item must be copied to # the client config file as well. ;cipher BF-CBC # Blowfish (default) ;cipher AES-128-CBC # AES ;cipher DES-EDE3-CBC # Triple-DES # Enable compression on the VPN link. # If you enable it here, you must also # enable it in the client config file. comp-lzo # The maximum number of concurrently connected # clients we want to allow. ;max-clients 100 # It's a good idea to reduce the OpenVPN # daemon's privileges after initialization. # # You can uncomment this out on # non-Windows systems. ;user nobody ;group nobody # The persist options will try to avoid # accessing certain resources on restart # that may no longer be accessible because # of the privilege downgrade. persist-key persist-tun # Output a short status file showing # current connections, truncated # and rewritten every minute. status openvpn-status.log # By default, log messages will go to the syslog (or # on Windows, if running as a service, they will go to # the "\Program Files\OpenVPN\log" directory). # Use log or log-append to override this default. # "log" will truncate the log file on OpenVPN startup, # while "log-append" will append to it. Use one # or the other (but not both). ;log openvpn.log ;log-append openvpn.log # Set the appropriate level of log # file verbosity. # # 0 is silent, except for fatal errors # 4 is reasonable for general usage # 5 and 6 can help to debug connection problems # 9 is extremely verbose verb 3 # Silence repeating messages. At most 20 # sequential messages of the same message # category will be output to the log. ;mute 20 I have changed IP's for security

Read the article

DD-WRT No Internet connection over LAN

- by algorithms

I flashed the DD-WRT firmware on my TP-Link WR1043ND router and although after cloning the PC's MAC-Address it gets the correct IP from my ISP, the internet connection over LAN just won't work. The strange thing is it does work flawlessly over W-LAN, which tells me the problem should lie somehow in the default LAN settings or the PC. Any idea what the problem might be? UPDATE: It seems the problem is the desktop PC, since the laptop can connect to the interet via ethernet without any problems. ipconfig /all seems totally normal (dhcp, dns, gateway all set to 192.168.1.1) I already tried the following things without success: disabling firewall rebooting router/modem/pc router hard-reset resetting tcp/ip and winsock manual setting of DNS/IP/Gateway Here is the ipconfig /all: Windows-IP-Konfiguration Hostname . . . . . . . . . . . . : Nitro-PC Primäres DNS-Suffix . . . . . . . : Knotentyp . . . . . . . . . . . . : Hybrid IP-Routing aktiviert . . . . . . : Nein WINS-Proxy aktiviert . . . . . . : Nein Ethernet-Adapter LAN-Verbindung 2: Medienstatus. . . . . . . . . . . : Medium getrennt Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : TAP-Win32 Adapter V9 Physikalische Adresse . . . . . . : 00-FF-56-CA-66-8D DHCP aktiviert. . . . . . . . . . : Ja Autokonfiguration aktiviert . . . : Ja Ethernet-Adapter LAN-Verbindung: Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Realtek PCIe GBE Family Controller Physikalische Adresse . . . . . . : 48-5B-39-5B-DE-17 DHCP aktiviert. . . . . . . . . . : Ja Autokonfiguration aktiviert . . . : Ja Verbindungslokale IPv6-Adresse . : fe80::6934:b121:9eab:c6ce%10(Bevorzugt) IPv4-Adresse . . . . . . . . . . : 192.168.1.18(Bevorzugt) Subnetzmaske . . . . . . . . . . : 255.255.255.0 Lease erhalten. . . . . . . . . . : Donnerstag, 30. August 2012 10:52:30 Lease läuft ab. . . . . . . . . . : Freitag, 31. August 2012 10:52:30 Standardgateway . . . . . . . . . : 192.168.1.1 DHCP-Server . . . . . . . . . . . : 192.168.1.1 DHCPv6-IAID . . . . . . . . . . . : 239622969 DHCPv6-Client-DUID. . . . . . . . : 00-01-00-01-17-43-0D-B2-48-5B-39-5B-DE-17 DNS-Server . . . . . . . . . . . : 192.168.1.1 NetBIOS über TCP/IP . . . . . . . : Aktiviert Tunneladapter isatap.{56CA668D-9112-4399-9D9A-F1D42F0E52DE}: Medienstatus. . . . . . . . . . . : Medium getrennt Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Microsoft-ISATAP-Adapter Physikalische Adresse . . . . . . : 00-00-00-00-00-00-00-E0 DHCP aktiviert. . . . . . . . . . : Nein Autokonfiguration aktiviert . . . : Ja Tunneladapter Teredo Tunneling Pseudo-Interface: Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physikalische Adresse . . . . . . : 00-00-00-00-00-00-00-E0 DHCP aktiviert. . . . . . . . . . : Nein Autokonfiguration aktiviert . . . : Ja IPv6-Adresse. . . . . . . . . . . : 2001:0:5ef5:79fd:1432:3dcd:3f57:feed(Bevorzugt) Verbindungslokale IPv6-Adresse . : fe80::1432:3dcd:3f57:feed%12(Bevorzugt) Standardgateway . . . . . . . . . : :: NetBIOS über TCP/IP . . . . . . . : Deaktiviert Tunneladapter isatap.{AD21069D-D2AF-423E-BF59-0B1CD0D235E8}: Medienstatus. . . . . . . . . . . : Medium getrennt Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Microsoft-ISATAP-Adapter #2 Physikalische Adresse . . . . . . : 00-00-00-00-00-00-00-E0 DHCP aktiviert. . . . . . . . . . : Nein Autokonfiguration aktiviert . . . : Ja Tunneladapter 6TO4 Adapter: Medienstatus. . . . . . . . . . . : Medium getrennt Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Microsoft-6zu4-Adapter Physikalische Adresse . . . . . . : 00-00-00-00-00-00-00-E0 DHCP aktiviert. . . . . . . . . . : Nein Autokonfiguration aktiviert . . . : Ja route PRINT IPv4-Routentabelle =========================================================================== Aktive Routen: Netzwerkziel Netzwerkmaske Gateway Schnittstelle Metrik 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.18 10 127.0.0.0 255.0.0.0 Auf Verbindung 127.0.0.1 306 127.0.0.1 255.255.255.255 Auf Verbindung 127.0.0.1 306 127.255.255.255 255.255.255.255 Auf Verbindung 127.0.0.1 306 192.168.1.0 255.255.255.0 Auf Verbindung 192.168.1.18 266 192.168.1.18 255.255.255.255 Auf Verbindung 192.168.1.18 266 192.168.1.255 255.255.255.255 Auf Verbindung 192.168.1.18 266 224.0.0.0 240.0.0.0 Auf Verbindung 127.0.0.1 306 224.0.0.0 240.0.0.0 Auf Verbindung 192.168.1.18 266 255.255.255.255 255.255.255.255 Auf Verbindung 127.0.0.1 306 255.255.255.255 255.255.255.255 Auf Verbindung 192.168.1.18 266 =========================================================================== Stndige Routen: Keine

Read the article

Wired connection periodically disconnects requires ipconfig /release and /renew to reconnect

- by Sesame

I just got back into University and after a day of using the internet I suddenly was unable to visit other webpages even though I was still able to chat. I restarted the computer and the internet could no longer visit webpages at all. I got a DNS error from the browser (chrome) and the troubleshooter. The connection comes up as "Network 3" even though It was "Network 2" when it worked. I compared ipconfig /all logs and they seemed identical when it was and was not working. I've found two ways to get internet connection (they no longer work): run ipconfig /release and ipconfig /renew several times set a random address and have the troubleshooter fix the new found dhcp problem (before it says dns cannot fix). I checked and it said DHCP was enabled. But either step one or two usually needs to be repeated several times before the network will change back to "network 2" from the defunct "network 3" and after an hour or so I have problems again. I've tried: Uninstalling windows defender and turning off firewall (windows firewall). Updating Qualcomm Ethernet driver - it is up to date. System Restore (problem resurfaces quickly...it's possible this has something to do with windows update?) Flushing dns and setting dns myself (google one and others). Booting in safe mode with networking...didn't fix anything Reinstalling Ethernet Driver Using other ethernet cable, other wall port. I'm out of ideas. Ipconfig /all: Windows IP Configuration Host Name . . . . . . . . . . . . : NGoller Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : Home Ethernet adapter UConnect: Connection-specific DNS Suffix . : Home Description . . . . . . . . . . . : Qualcomm Atheros AR8151 PCI-E Gigabit Ethernet Controller Physical Address. . . . . . . . . : 90-2B-34-50-33-F4 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv6 Address. . . . . . . . . . . : fd00::2086:628:f0a1:73c3(Preferred) Temporary IPv6 Address. . . . . . : fd00::c86b:370:b1d9:bd73(Preferred) Link-local IPv6 Address . . . . . : fe80::2086:628:f0a1:73c3%11(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.0.33(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Wednesday, August 28, 2013 11:58:37 PM Lease Expires . . . . . . . . . . : Thursday, August 29, 2013 11:58:37 PM Default Gateway . . . . . . . . . : 192.168.0.1 DHCP Server . . . . . . . . . . . : 192.168.0.1 DNS Servers . . . . . . . . . . . : 192.168.0.1 NetBIOS over Tcpip. . . . . . . . : Enabled Tunnel adapter isatap.Home: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Home Description . . . . . . . . . . . : Microsoft ISATAP Adapter Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes I'm getting these errors commonly: The IP address lease 155.97.227.199 for the Network Card with network address 0x902B345033F4 has been denied by the DHCP server 10.0.1.1 (The DHCP Server sent a DHCPNACK message). Event filter with query "SELECT * FROM __InstanceModificationEvent WITHIN 60 WHERE TargetInstance ISA "Win32_Processor" AND TargetInstance.LoadPercentage > 99" could not be reactivated in namespace "//./root/CIMV2" because of error 0x80041003. Events cannot be delivered through this filter until the problem is corrected. By the way, Operating System: Windows 7 - 64 Bit. Have downloaded latest windows updates. Update: And my two fixes don't work any more :( . This is now what happens when I try to Ipconfig /renew: C:\Users\Nikko\Desktop>ipconfig /renew Windows IP Configuration An error occurred while renewing interface Local Area Connection : The name spec ified in the network control block (NCB) is in use on a remote adapter. The NCB is the data. An error occurred while releasing interface Loopback Pseudo-Interface 1 : The sy stem cannot find the file specified. Update 2: So my internet is randomly working again today. The IP address I had before was a local one while the university address should start with 155... I didn't do anything to the settings...it's bizarre that it all of a sudden works. Thanks!

Read the article

Weird WLAN connection

- by tuelsch

I assembled my first computer on my own. As I realised it had no WLAN (AsRock Z77 Extreme 4m) I bought a WLAN stick (ZyXel NWD 2105), plugged it in, started the setup from the CD and it worked, until I restarted the PC. That's when the problems started. The stick is able to connect to the router (P-660HN-F1Z) and the connection is stable, but not the internet access. In estimately 1 minute intervals there might be a short connection timeframe and dropbox or windows update are able to download some data, but as soon as I try to open a website the internet access is away. Note that the connection to the router does not shut down and remains stable at around 80-90%. The problem is definetly located on my pc, because with my laptop and phone the connection is stable and fast. Because I was so pissed off, I bought a EW-7612PIn V2 (PCI-E WLAN adapter), same problem. Now the weird thing is, if I don't use the PC for about 2 days, start it up, there is internet access (happened with both the stick and the PCI-E card). A bit slow, but it does not get away just like that, until I shut it down. Then, no matter how many times I restart, it won't come back. I googled a lot but now I'm at the end with my latin. Has anyone had a similar problem and resolved it? Technical details: Motherboard: AsRock Z77 Extreme 4M OS: Windows 7 professional 64bit Stick: Zyxel wireless N adapter NWD2105 PCI-E card: Edimax EW-7612PIn V2 Router: ZyXel P-660HN-F1Z Windows-IP-Konfiguration Hostname . . . . . . . . . . . . : xyz Primäres DNS-Suffix . . . . . . . : Knotentyp . . . . . . . . . . . . : Hybrid IP-Routing aktiviert . . . . . . : Nein WINS-Proxy aktiviert . . . . . . : Nein Drahtlos-LAN-Adapter Drahtlosnetzwerkverbindung 5: Medienstatus. . . . . . . . . . . : Medium getrennt Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Microsoft Virtual WiFi Miniport Adapter # 3 Physikalische Adresse . . . . . . : 80-1F-02-61-C0-A6 DHCP aktiviert. . . . . . . . . . : Ja Autokonfiguration aktiviert . . . : Ja Drahtlos-LAN-Adapter Drahtlosnetzwerkverbindung 4: Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Edimax 802.11n Wireless Adapter Physikalische Adresse . . . . . . : 80-1F-02-61-C0-A6 DHCP aktiviert. . . . . . . . . . : Ja Autokonfiguration aktiviert . . . : Ja Verbindungslokale IPv6-Adresse . : fe80::38d2:f489:726d:1fb5%17(Bevorzugt) IPv4-Adresse . . . . . . . . . . : 192.168.1.41(Bevorzugt) Subnetzmaske . . . . . . . . . . : 255.255.255.0 Lease erhalten. . . . . . . . . . : Donnerstag, 15. November 2012 10:51:05 Lease läuft ab. . . . . . . . . . : Sonntag, 18. November 2012 10:51:18 Standardgateway . . . . . . . . . : 192.168.1.1 DHCP-Server . . . . . . . . . . . : 192.168.1.1 DHCPv6-IAID . . . . . . . . . . . : 578821890 DHCPv6-Client-DUID. . . . . . . . : 00-01-00-01-17-FF-D5-FE-BC-5F-F4-48-FC-4B DNS-Server . . . . . . . . . . . : 91.233.182.2 194.230.1.39 NetBIOS über TCP/IP . . . . . . . : Aktiviert Tunneladapter isatap.{263BEB98-344B-435C-888F-1B15B97C3AC1}: Medienstatus. . . . . . . . . . . : Medium getrennt Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Microsoft-ISATAP-Adapter Physikalische Adresse . . . . . . : 00-00-00-00-00-00-00-E0 DHCP aktiviert. . . . . . . . . . : Nein Autokonfiguration aktiviert . . . : Ja Tunneladapter Teredo Tunneling Pseudo-Interface: Verbindungsspezifisches DNS-Suffix: Beschreibung. . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physikalische Adresse . . . . . . : 00-00-00-00-00-00-00-E0 DHCP aktiviert. . . . . . . . . . : Nein Autokonfiguration aktiviert . . . : Ja IPv6-Adresse. . . . . . . . . . . : 2001:0:9d38:6ab8:209c:2944:3f57:fed6(Bevo rzugt) Verbindungslokale IPv6-Adresse . : fe80::209c:2944:3f57:fed6%11(Bevorzugt) Standardgateway . . . . . . . . . : :: NetBIOS über TCP/IP . . . . . . . : Deaktiviert C:\Users\xyz>ping 192.168.1.1 Ping wird ausgeführt für 192.168.1.1 mit 32 Bytes Daten: Antwort von 192.168.1.1: Bytes=32 Zeit=2ms TTL=254 Antwort von 192.168.1.1: Bytes=32 Zeit=2ms TTL=254 Antwort von 192.168.1.1: Bytes=32 Zeit=2ms TTL=254 Antwort von 192.168.1.1: Bytes=32 Zeit=2ms TTL=254 Ping-Statistik für 192.168.1.1: Pakete: Gesendet = 4, Empfangen = 4, Verloren = 0 (0% Verlust), Ca. Zeitangaben in Millisek.: Minimum = 2ms, Maximum = 2ms, Mittelwert = 2ms

Read the article

Windows Server 2008: specifying the default IP address when NIC has multiple addresses

- by Cédric Boivin

I have a Windows Server which has ~10 IP addresses statically bound. The problem is I don't know how to specify the default IP address. Sometimes when I assign a new address to the NIC, the default IP address changes with the last IP entered in the advanced IP configuration on the NIC. This has the effect (since I use NAT) that the outgoing public IP changes too. Even though this problem is currently on Windows Server 2008 How can you set the default IP address on a NIC when it has multiple IP addresses bound? There is more explication on my probleme. Here is the ipconfig DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.99.49(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.51(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.52(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.53(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.54(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.55(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.56(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.57(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.58(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.59(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.60(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.61(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.62(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.64(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.65(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.66(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.67(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.68(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.70(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.71(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.100(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.108(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.109(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.112(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 IPv4 Address. . . . . . . . . . . : 192.168.99.63(Duplicate) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.99.1 If i do a pathping there is the answer, the first up is the 99.49, also if my default ip is 99.100 Tracing route to www.l.google.com [72.14.204.99] over a maximum of 30 hops: 0 Machine [192.168.99.49] There is the routing table on the machine Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.99.1 192.168.99.49 261 10.10.10.0 255.255.255.0 On-link 10.10.10.10 261 10.10.10.10 255.255.255.255 On-link 10.10.10.10 261 10.10.10.255 255.255.255.255 On-link 10.10.10.10 261 192.168.99.0 255.255.255.0 On-link 192.168.99.49 261 192.168.99.49 255.255.255.255 On-link 192.168.99.49 261 192.168.99.51 255.255.255.255 On-link 192.168.99.49 261 192.168.99.52 255.255.255.255 On-link 192.168.99.49 261 192.168.99.53 255.255.255.255 On-link 192.168.99.49 261 192.168.99.54 255.255.255.255 On-link 192.168.99.49 261 192.168.99.55 255.255.255.255 On-link 192.168.99.49 261 192.168.99.56 255.255.255.255 On-link 192.168.99.49 261 192.168.99.57 255.255.255.255 On-link 192.168.99.49 261 192.168.99.58 255.255.255.255 On-link 192.168.99.49 261 192.168.99.59 255.255.255.255 On-link 192.168.99.49 261 192.168.99.60 255.255.255.255 On-link 192.168.99.49 261 192.168.99.61 255.255.255.255 On-link 192.168.99.49 261 192.168.99.62 255.255.255.255 On-link 192.168.99.49 261 192.168.99.64 255.255.255.255 On-link 192.168.99.49 261 192.168.99.65 255.255.255.255 On-link 192.168.99.49 261 192.168.99.66 255.255.255.255 On-link 192.168.99.49 261 192.168.99.67 255.255.255.255 On-link 192.168.99.49 261 192.168.99.68 255.255.255.255 On-link 192.168.99.49 261 192.168.99.70 255.255.255.255 On-link 192.168.99.49 261 192.168.99.71 255.255.255.255 On-link 192.168.99.49 261 192.168.99.100 255.255.255.255 On-link 192.168.99.49 261 192.168.99.108 255.255.255.255 On-link 192.168.99.49 261 192.168.99.109 255.255.255.255 On-link 192.168.99.49 261 192.168.99.112 255.255.255.255 On-link 192.168.99.49 261 192.168.99.255 255.255.255.255 On-link 192.168.99.49 261 224.0.0.0 240.0.0.0 On-link 192.168.99.49 261 224.0.0.0 240.0.0.0 On-link 10.10.10.10 261 255.255.255.255 255.255.255.255 On-link 192.168.99.49 261 255.255.255.255 255.255.255.255 On-link 10.10.10.10 261 How i can be sure the ip use in the image ( suppose to be the default ip address ) will be use by my server as the default address ?

Read the article

network is not available even when cisco vpn client is connected. wrong route?

- by javapowered

I'm using Vodafone 3G modem. I've disabled other network devices in the system (ethernet, wifi, wimax) turned off firewall and antivirus. cisco vpn client connects successfully but I still can not access computer 192.168.147.120 (as well as any other computer from network). Any suggestions are welcome as I don't know what to do. ipconfig /all and route print commands (translated to english): Microsoft Windows [Version 6.1.7601] (C) Microsoft Corporation (Microsoft Corp.), 2009. All rights reserved. C: \ Users \ Oleg> ipconfig / all IP Configuration for Windows The name of the computer. . . . . . . . . : OlegPC The primary DNS-suffix. . . . . . : Node Type. . . . . . . . . . . . . : Hybrid IP-routing is enabled. . . . : No WINS-proxy enabled. . . . . . . : No Ethernet adapter Local Area Connection 4: DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Cisco Systems VPN Adapter Physical Address. . . . . . . . . 00-05-9A-3C-78-00 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes Local IPv6-address channel. . . : Fe80:: c073: 41b2: 852f: eb87% 26 (Preferred) IPv4-address. . . . . . . . . . . . : 10.53.127.204 (Preferred) The subnet mask. . . . . . . . . . : 255.0.0.0 Default Gateway. . . . . . . . . : IAID DHCPv6. . . . . . . . . . . : 536872346 DUID the client DHCPv6. . . . . . . 00-01-00-01-14-6F-4C-8D-60-EB-69-85-10-2D DNS-servers. . . . . . . . . . . : Fec0: 0:0: ffff:: 1% 1 fec0: 0:0: ffff:: 2% 1 fec0: 0:0: ffff:: 3% 1 NetBios over TCP / IP. . . . . . . . : Disabled Adapter mobile broadband connection through a broadband adapter mobile communications: DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Vodafone Mobile Broadband Network Adapter (Huawei) Physical Address. . . . . . . . . 58-2C-80-13-92-63 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes IPv4-address. . . . . . . . . . . . : 10.229.227.77 (Preferred) The subnet mask. . . . . . . . . . : 255.255.255.252 Default Gateway. . . . . . . . . : 10.229.227.78 DNS-servers. . . . . . . . . . . : 163.121.128.134 212.103.160.18 NetBios over TCP / IP. . . . . . . . : Disabled Tunnel adapter isatap. {737FF02E-D473-4F91-840E-2A4DD293FC12}: State of the environment. . . . . . . . : DNS Suffix. DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Adapter Microsoft ISATAP # 3 Physical Address. . . . . . . . . 00-00-00-00-00-00-00-E0 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes Tunnel adapter isatap. {EF585226-5B07-4446-A5A4-CB1B8E4B13AC}: State of the environment. . . . . . . . : DNS Suffix. DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Adapter Microsoft ISATAP # 4 Physical Address. . . . . . . . . 00-00-00-00-00-00-00-E0 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: DNS-suffix for this connection. . . . . : Description. . . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . 00-00-00-00-00-00-00-E0 DHCP is enabled. . . . . . . . . . . : No Autoconfiguration Enabled. . . . . . : Yes IPv6-address. . . . . . . . . . . . : 2001:0:4137:9 e76: ea: b77: f51a: 1cb2 (Basically d) Local IPv6-address channel. . . : Fe80:: ea: b77: f51a: 1cb2% 16 (Preferred) Default Gateway. . . . . . . . . ::: NetBios over TCP / IP. . . . . . . . : Disabled C: \ Users \ Oleg> route print ================================================== ========================= List of interfaces 26 ... 00 05 9a 3c 78 00 ...... Cisco Systems VPN Adapter 23 ... 58 2c 80 13 92 63 ...... Vodafone Mobile Broadband Network Adapter (Huawei) 1 ........................... Software Loopback Interface 1 19 ... 00 00 00 00 00 00 00 e0 Adapter Microsoft ISATAP # 3 20 ... 00 00 00 00 00 00 00 e0 Adapter Microsoft ISATAP # 4 16 ... 00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface ================================================== ========================= IPv4 Route Table ================================================== ========================= Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.229.227.78 10.229.227.77 296 10.0.0.0 255.0.0.0 On-link 10.53.127.204 286 10.6.93.21 255,255,255,255 10.0.0.1 10.53.127.204 100 10.13.50.12 255,255,255,255 10.0.0.1 10.53.127.204 100 10.53.8.0 255.255.252.0 10.0.0.1 10.53.127.204 100 10.53.127.204 255.255.255.255 On-link 10.53.127.204 286 10.53.128.0 255.255.248.0 10.0.0.1 10.53.127.204 100 10.53.148.0 255,255,255,240 10.0.0.1 10.53.127.204 100 10.53.148.16 255,255,255,240 10.0.0.1 10.53.127.204 100 10.229.227.76 255.255.255.252 On-link 10.229.227.77 296 10.229.227.77 255.255.255.255 On-link 10.229.227.77 296 10.229.227.79 255.255.255.255 On-link 10.229.227.77 296 10.255.255.255 255.255.255.255 On-link 10.53.127.204 286 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.147.0 255,255,255,240 10.0.0.1 10.53.127.204 100 192.168.147.96 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,112 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,128 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,144 255,255,255,240 10.0.0.1 10.53.127.204 100 192,168,147,224 255,255,255,240 10.0.0.1 10.53.127.204 100 192.168.214.0 255.255.255.0 10.0.0.1 10.53.127.204 100 192.168.215.0 255.255.255.0 10.0.0.1 10.53.127.204 100 194.247.133.19 255,255,255,255 10.0.0.1 10.53.127.204 100 213,247,231,194 255,255,255,255 10.229.227.78 10.229.227.77 100 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.229.227.77 296 224.0.0.0 240.0.0.0 On-link 10.53.127.204 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.229.227.77 296 255.255.255.255 255.255.255.255 On-link 10.53.127.204 286 ================================================== ========================= Persistent Routes: None IPv6 Route Table ================================================== ========================= Active Routes: If Metric Network Destination Gateway 16 58:: / 0 On-link 1306:: 1 / 128 On-link 16 58 2001:: / 32 On-link 16 306 2001: 0:4137:9 e76: ea: b77: f51a: 1cb2/128 On-link 16 306 fe80:: / 64 On-link 26 286 fe80:: / 64 On-link 16 306 fe80:: ea: b77: f51a: 1cb2/128 On-link 26 286 fe80:: c073: 41b2: 852f: eb87/128 On-link 1306 ff00:: / 8 On-link 16 306 ff00:: / 8 On-link 26 286 ff00:: / 8 On-link ================================================== ========================= Persistent Routes: None C: \ Users \ Oleg>

Read the article

Unable to ping local machines by name in Windows 7

- by aardvarkk

I'm having a strange (and persistent!) problem with pinging local machines on my network by name. I believe my machine (Windows 7 64-bit) is the only one having this issue. This is over a wireless connection. As an example, consider a device on my network by the name of WDTVLiveHub. It's a Western Digital Live Hub (surprise!). If I go to my router's DHCP Client Table in the browser (my router is a WRT400N), I see this entry: WDTVLiveHub 192.168.1.101 Great. So I try to ping that IP address: ping 192.168.1.101 Pinging 192.168.1.101 with 32 bytes of data: Reply from 192.168.1.101: bytes=32 time=9ms TTL=64 Reply from 192.168.1.101: bytes=32 time=16ms TTL=64 Reply from 192.168.1.101: bytes=32 time=16ms TTL=64 Reply from 192.168.1.101: bytes=32 time=16ms TTL=64 Ping statistics for 192.168.1.101: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 9ms, Maximum = 16ms, Average = 14ms OK, still looking good. Now I try to ping it by name: ping WDTVLiveHub Ping request could not find host WDTVLiveHub. Please check the name and try again. From what I've read, this implies a problem with DNS servers and host name lookups. Interestingly, if I type the following: pathping 192.168.1.101 I get this output: Tracing route to WDTVLIVEHUB [192.168.1.101] over a maximum of 30 hops: 0 Scotty [192.168.1.103] 1 WDTVLIVEHUB [192.168.1.101] Computing statistics for 25 seconds... Source to Here This Node/Link Hop RTT Lost/Sent = Pct Lost/Sent = Pct Address 0 Scotty [192.168.1.103] 1/ 100 = 1% | 1 12ms 1/ 100 = 1% 0/ 100 = 0% WDTVLIVEHUB [192.168.1.101] Trace complete. Scotty is obviously the name of my local machine. So it's able to find the name somehow when I do that approach... ipconfig /all shows the following under DNS servers: DNS Servers . . . . . . . . . . . : 192.168.1.1 ***.***.***.*** ***.***.***.*** Where the * represents the same DNS servers that show up in my router under DNS 1 and DNS 2 through the Internet. For completeness, here's the whole output of ipconfig /all: Windows IP Configuration Host Name . . . . . . . . . . . . : Scotty Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Peer-Peer IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Dell Wireless 1397 WLAN Mini-Card Physical Address. . . . . . . . . : 0C-EE-E6-D1-07-E8 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv6 Address. . . . . . . . . . . : 2002:d83a:31e5:1234:5592:398e:8968:43d1(Preferred) Temporary IPv6 Address. . . . . . : 2002:d83a:31e5:1234:ecce:2f79:72a5:5273(Preferred) Link-local IPv6 Address . . . . . : fe80::5592:398e:8968:43d1%26(Preferred) IPv4 Address. . . . . . . . . . . : 192.168.1.103(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : September-17-12 11:05:57 PM Lease Expires . . . . . . . . . . : September-18-12 11:05:57 PM Default Gateway . . . . . . . . . : fe80::200:ff:fe00:0%26 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DHCPv6 IAID . . . . . . . . . . . : 537718502 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-12-80-3D-D7-00-26-B9-0D-08-70 DNS Servers . . . . . . . . . . . : 192.168.1.1 ***.***.***.*** ***.***.***.*** NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter VirtualBox Host-Only Network: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VirtualBox Host-Only Ethernet Adapter Physical Address. . . . . . . . . : 08-00-27-00-98-9A DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::b48a:916b:c0f:fb29%23(Preferred) Autoconfiguration IPv4 Address. . : 169.254.251.41(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : DHCPv6 IAID . . . . . . . . . . . : 570949671 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-12-80-3D-D7-00-26-B9-0D-08-70 DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1 fec0:0:0:ffff::2%1 fec0:0:0:ffff::3%1 NetBIOS over Tcpip. . . . . . . . : Enabled Tunnel adapter Local Area Connection* 15: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter isatap.{55899375-C31D-4173-A529-4427D63FD28B}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft ISATAP Adapter #2 Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter isatap.{64B8F35F-A6AB-4D6B-B1D5-DD95F57B1458}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft ISATAP Adapter #3 Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Not sure exactly how to diagnose exactly what's going on... but the problem is really frustrating! The biggest problem is that my mapped network drives have to be done by IP, and then any time the router assigns new IP addresses to those devices, all of my network shares break again. Stinks! Would love some assistance on possible solutions. I've tried all of this netsh catalog resetting and that didn't seem to fix anything at all. Would love an explanation of what's going wrong, too, rather than blindly resetting things! Thanks!

Read the article

Garbled text in Screen [closed]

- by Prabin Dahal

The graphical Interface in my system is garbled with some text. At the beginning I thought it was due to java and tomcat that I installed. But after removing java and tomcat, it is still the same. I am using ubuntu server and i have installed xfce desktop environment with oboard softkey I have added my dmesg output to this message. What is the problem here. I am not able to figure it out. Thank you for your help. Prabin [ 0.390936] usbcore: registered new interface driver usbfs [ 0.391006] usbcore: registered new interface driver hub [ 0.391147] usbcore: registered new device driver usb [ 0.391580] PCI: Using ACPI for IRQ routing [ 0.400509] PCI: pci_cache_line_size set to 64 bytes [ 0.400669] reserve RAM buffer: 000000000009ec00 - 000000000009ffff [ 0.400681] reserve RAM buffer: 000000007f597000 - 000000007fffffff [ 0.400699] reserve RAM buffer: 000000007f6f0000 - 000000007fffffff [ 0.401135] NetLabel: Initializing [ 0.401155] NetLabel: domain hash size = 128 [ 0.401168] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.401212] NetLabel: unlabeled traffic allowed by default [ 0.401466] HPET: 3 timers in total, 0 timers will be used for per-cpu timer [ 0.401494] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.401520] hpet0: 3 comparators, 64-bit 14.318180 MHz counter [ 0.408228] Switching to clocksource hpet [ 0.434341] AppArmor: AppArmor Filesystem Enabled [ 0.434447] pnp: PnP ACPI init [ 0.434531] ACPI: bus type pnp registered [ 0.434784] pnp 00:00: [bus 00-ff] [ 0.434794] pnp 00:00: [io 0x0cf8-0x0cff] [ 0.434804] pnp 00:00: [io 0x0000-0x0cf7 window] [ 0.434813] pnp 00:00: [io 0x0d00-0xffff window] [ 0.434822] pnp 00:00: [mem 0x000a0000-0x000bffff window] [ 0.434831] pnp 00:00: [mem 0x00000000 window] [ 0.434840] pnp 00:00: [mem 0x80000000-0xffffffff window] [ 0.435018] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active) [ 0.435526] pnp 00:01: [mem 0xe0000000-0xefffffff] [ 0.435537] pnp 00:01: [mem 0x7f700000-0x7f7fffff] [ 0.435545] pnp 00:01: [mem 0x7f800000-0x7fffffff] [ 0.435554] pnp 00:01: [mem 0xfee00000-0xfeefffff] [ 0.435727] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved [ 0.435754] system 00:01: [mem 0x7f700000-0x7f7fffff] has been reserved [ 0.435775] system 00:01: [mem 0x7f800000-0x7fffffff] has been reserved [ 0.435796] system 00:01: [mem 0xfee00000-0xfeefffff] has been reserved [ 0.435818] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.436233] pnp 00:02: [io 0x0000-0xffffffffffffffff disabled] [ 0.436245] pnp 00:02: [io 0x0000-0xffffffffffffffff disabled] [ 0.436414] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.436512] pnp 00:03: [io 0x0060] [ 0.436521] pnp 00:03: [io 0x0064] [ 0.436548] pnp 00:03: [irq 1] [ 0.436682] pnp 00:03: Plug and Play ACPI device, IDs PNP0303 PNP030b (active) [ 0.436825] pnp 00:04: [irq 12] [ 0.436958] pnp 00:04: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active) [ 0.437835] pnp 00:05: [io 0x03f8-0x03ff] [ 0.437861] pnp 00:05: [irq 4] [ 0.437870] pnp 00:05: [dma 0 disabled] [ 0.438142] pnp 00:05: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.439014] pnp 00:06: [io 0x02f8-0x02ff] [ 0.439036] pnp 00:06: [irq 3] [ 0.439045] pnp 00:06: [dma 0 disabled] [ 0.439297] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.439346] pnp 00:07: [io 0x0000-0x000f] [ 0.439355] pnp 00:07: [io 0x0081-0x0083] [ 0.439363] pnp 00:07: [io 0x0087] [ 0.439371] pnp 00:07: [io 0x0089-0x008b] [ 0.439380] pnp 00:07: [io 0x008f] [ 0.439388] pnp 00:07: [io 0x00c0-0x00df] [ 0.439563] system 00:07: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.439617] pnp 00:08: [io 0x0070-0x0077] [ 0.439639] pnp 00:08: [irq 8] [ 0.439751] pnp 00:08: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.439788] pnp 00:09: [io 0x0061] [ 0.439893] pnp 00:09: Plug and Play ACPI device, IDs PNP0800 (active) [ 0.439977] pnp 00:0a: [io 0x0010-0x001f] [ 0.439986] pnp 00:0a: [io 0x0022-0x003f] [ 0.439994] pnp 00:0a: [io 0x0044-0x005f] [ 0.440055] pnp 00:0a: [io 0x0063] [ 0.440063] pnp 00:0a: [io 0x0065] [ 0.440071] pnp 00:0a: [io 0x0067-0x006f] [ 0.440079] pnp 00:0a: [io 0x0072-0x007f] [ 0.440086] pnp 00:0a: [io 0x0080] [ 0.440094] pnp 00:0a: [io 0x0084-0x0086] [ 0.440102] pnp 00:0a: [io 0x0088] [ 0.440109] pnp 00:0a: [io 0x008c-0x008e] [ 0.440117] pnp 00:0a: [io 0x0090-0x009f] [ 0.440125] pnp 00:0a: [io 0x00a2-0x00bf] [ 0.440133] pnp 00:0a: [io 0x00e0-0x00ef] [ 0.440141] pnp 00:0a: [io 0x04d0-0x04d1] [ 0.440150] pnp 00:0a: [io 0x0000-0xffffffffffffffff disabled] [ 0.440160] pnp 00:0a: [io 0x0000-0xffffffffffffffff disabled] [ 0.440168] pnp 00:0a: [io 0x03f4] [ 0.440175] pnp 00:0a: [io 0x03f5] [ 0.440183] pnp 00:0a: [io 0x0374] [ 0.440190] pnp 00:0a: [io 0x0375] [ 0.440405] system 00:0a: [io 0x04d0-0x04d1] has been reserved [ 0.440432] system 00:0a: [io 0x03f4] has been reserved [ 0.440451] system 00:0a: [io 0x03f5] has been reserved [ 0.440469] system 00:0a: [io 0x0374] has been reserved [ 0.440488] system 00:0a: [io 0x0375] has been reserved [ 0.440508] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.440550] pnp 00:0b: [io 0x00f0-0x00ff] [ 0.440572] pnp 00:0b: [irq 13] [ 0.440691] pnp 00:0b: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.440770] pnp 00:0c: [io 0x0810] [ 0.440779] pnp 00:0c: [io 0x0800-0x080f] [ 0.440787] pnp 00:0c: [io 0xffff] [ 0.440947] system 00:0c: [io 0x0810] has been reserved [ 0.440970] system 00:0c: [io 0x0800-0x080f] has been reserved [ 0.440989] system 00:0c: [io 0xffff] has been reserved [ 0.441010] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.441620] pnp 00:0d: [io 0x0900-0x097f] [ 0.441630] pnp 00:0d: [io 0x09c0-0x09ff] [ 0.441639] pnp 00:0d: [io 0x0400-0x043f] [ 0.441647] pnp 00:0d: [io 0x0480-0x04bf] [ 0.441656] pnp 00:0d: [mem 0xfec00000-0xfec85fff] [ 0.441664] pnp 00:0d: [mem 0xfed1c000-0xfed1ffff] [ 0.441673] pnp 00:0d: [mem 0x000c0000-0x000dffff] [ 0.441689] pnp 00:0d: [mem 0x000e0000-0x000effff] [ 0.441697] pnp 00:0d: [mem 0x000f0000-0x000fffff] [ 0.441706] pnp 00:0d: [mem 0xff800000-0xffffffff] [ 0.441911] system 00:0d: [io 0x0900-0x097f] has been reserved [ 0.441935] system 00:0d: [io 0x09c0-0x09ff] has been reserved [ 0.441955] system 00:0d: [io 0x0400-0x043f] has been reserved [ 0.441975] system 00:0d: [io 0x0480-0x04bf] has been reserved [ 0.441997] system 00:0d: [mem 0xfec00000-0xfec85fff] could not be reserved [ 0.442019] system 00:0d: [mem 0xfed1c000-0xfed1ffff] has been reserved [ 0.442040] system 00:0d: [mem 0x000c0000-0x000dffff] could not be reserved [ 0.442061] system 00:0d: [mem 0x000e0000-0x000effff] could not be reserved [ 0.442082] system 00:0d: [mem 0x000f0000-0x000fffff] could not be reserved [ 0.442103] system 00:0d: [mem 0xff800000-0xffffffff] has been reserved [ 0.442126] system 00:0d: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.442308] pnp 00:0e: [mem 0xfed00000-0xfed003ff] [ 0.442454] pnp 00:0e: Plug and Play ACPI device, IDs PNP0103 (active) [ 0.442569] pnp 00:0f: [mem 0x7f6f0000-0x7f6fffff] [ 0.442762] system 00:0f: [mem 0x7f6f0000-0x7f6fffff] has been reserved [ 0.442788] system 00:0f: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.443360] pnp: PnP ACPI: found 16 devices [ 0.443378] ACPI: ACPI bus type pnp unregistered [ 0.443395] PnPBIOS: Disabled by ACPI PNP [ 0.486106] PCI: max bus depth: 3 pci_try_num: 4 [ 0.486189] pci 0000:00:1c.0: PCI bridge to [bus 01-01] [ 0.486217] pci 0000:00:1c.0: bridge window [io 0xe000-0xefff] [ 0.486241] pci 0000:00:1c.0: bridge window [mem 0xd0100000-0xd01fffff] [ 0.486266] pci 0000:00:1c.0: bridge window [mem 0xff700000-0xff7fffff pref] [ 0.486298] pci 0000:03:01.0: PCI bridge to [bus 04-04] [ 0.486319] pci 0000:03:01.0: bridge window [io 0xd000-0xdfff] [ 0.486348] pci 0000:03:01.0: bridge window [mem 0xd0000000-0xd00fffff] [ 0.486374] pci 0000:03:01.0: bridge window [mem 0xff600000-0xff6fffff 64bit pref] [ 0.486406] pci 0000:03:02.0: PCI bridge to [bus 05-05] [ 0.486444] pci 0000:03:03.0: PCI bridge to [bus 06-06] [ 0.486479] pci 0000:02:00.0: PCI bridge to [bus 03-06] [ 0.486499] pci 0000:02:00.0: bridge window [io 0xd000-0xdfff] [ 0.486522] pci 0000:02:00.0: bridge window [mem 0xd0000000-0xd00fffff] [ 0.486545] pci 0000:02:00.0: bridge window [mem 0xff600000-0xff6fffff 64bit pref] [ 0.486575] pci 0000:00:1c.1: PCI bridge to [bus 02-06] [ 0.486593] pci 0000:00:1c.1: bridge window [io 0xd000-0xdfff] [ 0.486615] pci 0000:00:1c.1: bridge window [mem 0xd0000000-0xd00fffff] [ 0.486637] pci 0000:00:1c.1: bridge window [mem 0xff600000-0xff6fffff pref] [ 0.486710] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.486735] pci 0000:00:1c.0: setting latency timer to 64 [ 0.486774] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 0.486796] pci 0000:00:1c.1: setting latency timer to 64 [ 0.486817] pci 0000:02:00.0: setting latency timer to 64 [ 0.486836] pci 0000:03:01.0: setting latency timer to 64 [ 0.486858] pci 0000:03:02.0: setting latency timer to 64 [ 0.486880] pci 0000:03:03.0: setting latency timer to 64 [ 0.486893] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 0.486902] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 0.486912] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 0.486922] pci_bus 0000:00: resource 7 [mem 0x80000000-0xffffffff] [ 0.486932] pci_bus 0000:01: resource 0 [io 0xe000-0xefff] [ 0.486941] pci_bus 0000:01: resource 1 [mem 0xd0100000-0xd01fffff] [ 0.486951] pci_bus 0000:01: resource 2 [mem 0xff700000-0xff7fffff pref] [ 0.486961] pci_bus 0000:02: resource 0 [io 0xd000-0xdfff] [ 0.486970] pci_bus 0000:02: resource 1 [mem 0xd0000000-0xd00fffff] [ 0.486980] pci_bus 0000:02: resource 2 [mem 0xff600000-0xff6fffff pref] [ 0.486989] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff] [ 0.486998] pci_bus 0000:03: resource 1 [mem 0xd0000000-0xd00fffff] [ 0.487008] pci_bus 0000:03: resource 2 [mem 0xff600000-0xff6fffff 64bit pref] [ 0.487018] pci_bus 0000:04: resource 0 [io 0xd000-0xdfff] [ 0.487028] pci_bus 0000:04: resource 1 [mem 0xd0000000-0xd00fffff] [ 0.487038] pci_bus 0000:04: resource 2 [mem 0xff600000-0xff6fffff 64bit pref] [ 0.487177] NET: Registered protocol family 2 [ 0.487405] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.488397] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.489792] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.490493] TCP: Hash tables configured (established 131072 bind 65536) [ 0.490525] TCP reno registered [ 0.490551] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.490590] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.490898] NET: Registered protocol family 1 [ 0.490970] pci 0000:00:02.0: Boot video device [ 0.491052] pci 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 0.491092] pci 0000:00:1d.0: PCI INT A disabled [ 0.491134] pci 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 0.491174] pci 0000:00:1d.1: PCI INT B disabled [ 0.491220] pci 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22 [ 0.491259] pci 0000:00:1d.2: PCI INT C disabled [ 0.491307] pci 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23 [ 0.864431] Freeing initrd memory: 13820k freed [ 2.088042] pci 0000:00:1d.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001 [ 2.088207] pci 0000:00:1d.7: PCI INT D disabled [ 2.088267] PCI: CLS 64 bytes, default 64 [ 2.089248] audit: initializing netlink socket (disabled) [ 2.089287] type=2000 audit(1349363630.084:1): initialized [ 2.144783] highmem bounce pool size: 64 pages [ 2.144808] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 2.160057] VFS: Disk quotas dquot_6.5.2 [ 2.160232] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.161716] fuse init (API version 7.17) [ 2.161995] msgmni has been set to 1713 [ 2.162925] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 2.163008] io scheduler noop registered [ 2.163023] io scheduler deadline registered [ 2.163048] io scheduler cfq registered (default) [ 2.163339] pcieport 0000:00:1c.0: setting latency timer to 64 [ 2.163530] pcieport 0000:00:1c.1: setting latency timer to 64 [ 2.163706] pcieport 0000:02:00.0: setting latency timer to 64 [ 2.163873] pcieport 0000:03:01.0: setting latency timer to 64 [ 2.163964] pcieport 0000:03:01.0: irq 40 for MSI/MSI-X [ 2.164193] pcieport 0000:03:02.0: setting latency timer to 64 [ 2.164272] pcieport 0000:03:02.0: irq 41 for MSI/MSI-X [ 2.164453] pcieport 0000:03:03.0: setting latency timer to 64 [ 2.164531] pcieport 0000:03:03.0: irq 42 for MSI/MSI-X [ 2.164783] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt [ 2.164801] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 2.164816] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded [ 2.164853] pcieport 0000:00:1c.1: Signaling PME through PCIe PME interrupt [ 2.164867] pcieport 0000:02:00.0: Signaling PME through PCIe PME interrupt [ 2.164880] pcieport 0000:03:01.0: Signaling PME through PCIe PME interrupt [ 2.164892] pci 0000:04:00.0: Signaling PME through PCIe PME interrupt [ 2.164904] pcieport 0000:03:02.0: Signaling PME through PCIe PME interrupt [ 2.164917] pcieport 0000:03:03.0: Signaling PME through PCIe PME interrupt [ 2.164932] pcie_pme 0000:00:1c.1:pcie01: service driver pcie_pme loaded [ 2.164988] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 2.165115] pciehp 0000:00:1c.0:pcie04: HPC vendor_id 8086 device_id 8110 ss_vid 8086 ss_did 8119 [ 2.165177] pciehp 0000:00:1c.0:pcie04: service driver pciehp loaded [ 2.165199] pciehp 0000:00:1c.1:pcie04: HPC vendor_id 8086 device_id 8112 ss_vid 8086 ss_did 8119 [ 2.165260] pciehp 0000:00:1c.1:pcie04: service driver pciehp loaded [ 2.165290] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 2.165488] intel_idle: MWAIT substates: 0x3020220 [ 2.165508] intel_idle: v0.4 model 0x1C [ 2.165513] intel_idle: lapic_timer_reliable_states 0x2 [ 2.165519] Marking TSC unstable due to TSC halts in idle states deeper than C2 [ 2.165779] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0 [ 2.165855] ACPI: Lid Switch [LID] [ 2.165983] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1 [ 2.166005] ACPI: Power Button [PWRB] [ 2.173811] thermal LNXTHERM:00: registered as thermal_zone0 [ 2.173829] ACPI: Thermal Zone [TZ00] (48 C) [ 2.174004] thermal LNXTHERM:01: registered as thermal_zone1 [ 2.174018] ACPI: Thermal Zone [TZ01] (34 C) [ 2.174194] thermal LNXTHERM:02: registered as thermal_zone2 [ 2.174207] ACPI: Thermal Zone [TZ02] (34 C) [ 2.174378] thermal LNXTHERM:03: registered as thermal_zone3 [ 2.174392] ACPI: Thermal Zone [TZ03] (34 C) [ 2.174503] ERST: Table is not found! [ 2.174513] GHES: HEST is not enabled! [ 2.174601] isapnp: Scanning for PnP cards... [ 2.176175] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 2.196702] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 2.292409] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 2.528909] isapnp: No Plug & Play device found [ 2.588733] 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 2.624523] 00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 2.640702] Linux agpgart interface v0.103 [ 2.645138] brd: module loaded [ 2.647452] loop: module loaded [ 2.648149] pata_acpi 0000:00:1f.1: setting latency timer to 64 [ 2.649238] Fixed MDIO Bus: probed [ 2.649315] tun: Universal TUN/TAP device driver, 1.6 [ 2.649327] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 2.649524] PPP generic driver version 2.4.2 [ 2.649824] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.649884] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23 [ 2.649937] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 2.649946] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 2.650082] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 [ 2.650148] ehci_hcd 0000:00:1d.7: debug port 1 [ 2.654045] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported [ 2.654093] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd02c4000 [ 2.668035] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 2.668392] hub 1-0:1.0: USB hub found [ 2.668413] hub 1-0:1.0: 8 ports detected [ 2.668618] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.668666] uhci_hcd: USB Universal Host Controller Interface driver [ 2.668726] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 2.668751] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 2.668759] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 2.668910] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 2.668981] uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000f040 [ 2.669335] hub 2-0:1.0: USB hub found [ 2.669355] hub 2-0:1.0: 2 ports detected [ 2.669508] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 2.669531] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 2.669538] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 2.669675] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 [ 2.669739] uhci_hcd 0000:00:1d.1: irq 21, io base 0x0000f020 [ 2.670099] hub 3-0:1.0: USB hub found [ 2.670118] hub 3-0:1.0: 2 ports detected [ 2.670271] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22 [ 2.670295] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 2.670302] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 2.670435] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 [ 2.670502] uhci_hcd 0000:00:1d.2: irq 22, io base 0x0000f000 [ 2.670869] hub 4-0:1.0: USB hub found [ 2.670888] hub 4-0:1.0: 2 ports detected [ 2.671186] usbcore: registered new interface driver libusual [ 2.671332] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 [ 2.673408] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.673437] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.673844] mousedev: PS/2 mouse device common for all mice [ 2.674272] rtc_cmos 00:08: RTC can wake from S4 [ 2.674482] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0 [ 2.674529] rtc0: alarms up to one year, y3k, 242 bytes nvram, hpet irqs [ 2.674691] device-mapper: uevent: version 1.0.3 [ 2.674903] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected] [ 2.675024] EISA: Probing bus 0 at eisa.0 [ 2.675037] EISA: Cannot allocate resource for mainboard [ 2.675050] Cannot allocate resource for EISA slot 1 [ 2.675061] Cannot allocate resource for EISA slot 2 [ 2.675072] Cannot allocate resource for EISA slot 3 [ 2.675083] Cannot allocate resource for EISA slot 4 [ 2.675094] Cannot allocate resource for EISA slot 5 [ 2.675105] Cannot allocate resource for EISA slot 6 [ 2.675116] Cannot allocate resource for EISA slot 7 [ 2.675127] Cannot allocate resource for EISA slot 8 [ 2.675137] EISA: Detected 0 cards. [ 2.675161] cpufreq-nforce2: No nForce2 chipset. [ 2.675401] cpuidle: using governor ladder [ 2.675786] cpuidle: using governor menu [ 2.675797] EFI Variables Facility v0.08 2004-May-17 [ 2.676429] TCP cubic registered [ 2.676751] NET: Registered protocol family 10 [ 2.678031] NET: Registered protocol family 17 [ 2.678052] Registering the dns_resolver key type [ 2.678107] Using IPI No-Shortcut mode [ 2.678515] PM: Hibernation image not present or could not be loaded. [ 2.678543] registered taskstats version 1 [ 2.701145] Magic number: 0:84:234 [ 2.701312] rtc_cmos 00:08: setting system clock to 2012-10-04 15:13:51 UTC (1349363631) [ 2.702280] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 2.702294] EDD information not available. [ 2.702858] Freeing unused kernel memory: 740k freed [ 2.703630] Write protecting the kernel text: 5816k [ 2.703692] Write protecting the kernel read-only data: 2376k [ 2.703706] NX-protecting the kernel data: 4424k [ 2.751226] udevd[84]: starting version 175 [ 2.980162] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 3.001394] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.001474] r8169 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 3.001554] r8169 0000:01:00.0: setting latency timer to 64 [ 3.001654] r8169 0000:01:00.0: irq 43 for MSI/MSI-X [ 3.004220] r8169 0000:01:00.0: eth0: RTL8168c/8111c at 0xf8416000, 00:18:92:03:10:46, XID 1c4000c0 IRQ 43 [ 3.004254] r8169 0000:01:00.0: eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko] [ 3.004347] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.005085] r8169 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 3.005182] r8169 0000:04:00.0: setting latency timer to 64 [ 3.005292] r8169 0000:04:00.0: irq 44 for MSI/MSI-X [ 3.007187] r8169 0000:04:00.0: eth1: RTL8168c/8111c at 0xf8418000, 00:18:92:03:10:47, XID 1c4000c0 IRQ 44 [ 3.007224] r8169 0000:04:00.0: eth1: jumbo features [frames: 6128 bytes, tx checksumming: ko] [ 3.034417] pata_sch 0000:00:1f.1: version 0.2 [ 3.034518] pata_sch 0000:00:1f.1: setting latency timer to 64 [ 3.036698] scsi0 : pata_sch [ 3.039842] scsi1 : pata_sch [ 3.040913] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf060 irq 14 [ 3.040940] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf068 irq 15 [ 3.131850] Initializing USB Mass Storage driver... [ 3.136405] scsi2 : usb-storage 1-1:1.0 [ 3.136642] usbcore: registered new interface driver usb-storage [ 3.136656] USB Mass Storage support registered. [ 3.524465] usb 3-1: new low-speed USB device number 2 using uhci_hcd [ 3.968144] usb 3-2: new full-speed USB device number 3 using uhci_hcd [ 4.137903] scsi 2:0:0:0: Direct-Access TS TS4GUFM-H 1100 PQ: 0 ANSI: 0 CCS [ 4.140067] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 4.140590] sd 2:0:0:0: [sda] 8028160 512-byte logical blocks: (4.11 GB/3.82 GiB) [ 4.141597] sd 2:0:0:0: [sda] Write Protect is off [ 4.141618] sd 2:0:0:0: [sda] Mode Sense: 43 00 00 00 [ 4.142974] sd 2:0:0:0: [sda] No Caching mode page present [ 4.143000] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.145837] sd 2:0:0:0: [sda] No Caching mode page present [ 4.145858] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.147931] sda: sda1 sda2 < sda5 > [ 4.150972] sd 2:0:0:0: [sda] No Caching mode page present [ 4.151001] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.151023] sd 2:0:0:0: [sda] Attached SCSI disk [ 4.249168] input: HID 046a:004b as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input2 [ 4.249579] generic-usb 0003:046A:004B.0001: input,hidraw0: USB HID v1.11 Keyboard [HID 046a:004b] on usb-0000:00:1d.1-1/input0 [ 4.287805] input: HID 046a:004b as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.1/input/input3 [ 4.289235] generic-usb 0003:046A:004B.0002: input,hidraw1: USB HID v1.11 Mouse [HID 046a:004b] on usb-0000:00:1d.1-1/input1 [ 4.297604] input: EloTouchSystems,Inc Elo TouchSystems 2216 AccuTouch\xffffffc2\xffffffae\xffffffae USB Touchmonitor Interface as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2:1.0/input/input4 [ 4.298913] generic-usb 0003:04E7:0050.0003: input,hidraw2: USB HID v1.00 Pointer [EloTouchSystems,Inc Elo TouchSystems 2216 AccuTouch\xffffffc2\xffffffae\xffffffae USB Touchmonitor Interface] on usb-0000:00:1d.1-2/input0 [ 4.299878] usbcore: registered new interface driver usbhid [ 4.299925] usbhid: USB HID core driver [ 4.352639] EXT4-fs (sda1): INFO: recovery required on readonly filesystem [ 4.352661] EXT4-fs (sda1): write access will be enabled during recovery [ 8.519257] EXT4-fs (sda1): recovery complete [ 8.564389] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 14.280922] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 14.280944] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 14.310368] udevd[308]: starting version 175 [ 14.353873] Adding 1045500k swap on /dev/sda5. Priority:-1 extents:1 across:1045500k [ 14.428718] lp: driver loaded but no devices found [ 14.521667] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 15.073459] [drm] Initialized drm 1.1.0 20060810 [ 15.097073] psb_gfx: module is from the staging directory, the quality is unknown, you have been warned. [ 15.180630] gma500 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 15.180648] gma500 0000:00:02.0: setting latency timer to 64 [ 15.182117] Stolen memory information [ 15.182127] base in RAM: 0x7f800000 [ 15.182134] size: 7932K, calculated by (GTT RAM base) - (Stolen base), seems wrong [ 15.182143] the correct size should be: 8M(dvmt mode=3) [ 15.234889] Set up 1983 stolen pages starting at 0x7f800000, GTT offset 0K [ 15.235126] [drm] SGX core id = 0x01130000 [ 15.235135] [drm] SGX core rev major = 0x01, minor = 0x02 [ 15.235143] [drm] SGX core rev maintenance = 0x01, designer = 0x00 [ 15.268796] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness [ 15.269888] acpi device:04: registered as cooling_device2 [ 15.270568] acpi device:05: registered as cooling_device3 [ 15.270947] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input5 [ 15.271238] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 15.271424] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 15.271434] [drm] No driver support for vblank timestamp query. [ 15.374694] type=1400 audit(1349363644.167:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=435 comm="apparmor_parser" [ 15.385518] type=1400 audit(1349363644.179:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=435 comm="apparmor_parser" [ 15.386369] type=1400 audit(1349363644.179:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=435 comm="apparmor_parser" [ 15.677514] r8169 0000:01:00.0: eth0: link down [ 15.694828] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.537490] gma500 0000:00:02.0: allocated 800x480 fb [ 16.558066] fbcon: psbfb (fb0) is primary device [ 16.747122] gma500 0000:00:02.0: BL bug: Reg 00000000 save 00000000 [ 16.775550] Console: switching to colour frame buffer device 100x30 [ 16.781804] fb0: psbfb frame buffer device [ 16.781812] drm: registered panic notifier [ 16.870168] [drm] Initialized gma500 1.0.0 2011-06-06 for 0000:00:02.0 on minor 0 [ 16.871166] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0 [ 16.871186] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0 [ 16.871207] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 16.871284] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 29.338953] r8169 0000:01:00.0: eth0: link up [ 29.339471] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 31.427223] init: failsafe main process (675) killed by TERM signal [ 31.522411] type=1400 audit(1349363660.316:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=889 comm="apparmor_parser" [ 31.523956] type=1400 audit(1349363660.316:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=889 comm="apparmor_parser" [ 31.524882] type=1400 audit(1349363660.320:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=889 comm="apparmor_parser" [ 31.525940] type=1400 audit(1349363660.320:8): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=891 comm="apparmor_parser" [ 34.526445] postgres (1003): /proc/1003/oom_adj is deprecated, please use /proc/1003/oom_score_adj instead. [ 40.144048] eth0: no IPv6 routers present

Search Results

Search found 9478 results on 380 pages for 'rails routing'.

Page 379/380 | < Previous Page | 375 376 377 378 379 380 | Next Page >

- by MasterRoot24

- by eComEvo

- by Rodnower

- by Austin

- by Chris

- by yasser abd

- by Mark Allison

- by Paul Dinh

- by Mark Tomlin

- by Jens

- by Ian

- by ami

- by ScottGu

- by thangchung

- by SaveTheRbtz

- by Dean Richardson

- by user263115

- by niico

- by algorithms

- by Sesame

- by tuelsch

- by Cédric Boivin

- by javapowered

- by aardvarkk

- by Prabin Dahal

< Previous Page | 375 376 377 378 379 380 | Next Page >