Search Results

Search found 12753 results on 511 pages for 'small'.

Page 379/511 | < Previous Page | 375 376 377 378 379 380 381 382 383 384 385 386  | Next Page >

• Software for RAID Failure Alerts?

  - by QF_Developer

  I have two 256 GB Samsung 840 Pro SSD disks in a RAID 1 array. I would like to receive a notification if one of the disks in the array fails. Can anybody recommend an application I can install on the server to fire an email if such an event occurs? Here are some additional specs: Supermicro X9SCM-IIF motherboard utilising the hardware RAID controller. OS = Windows 2012 Standard Also is it possible to simulate a disk failure by pulling it out of the bay? SSDs appear to fail close together when in a mirrored config so I'd like to know ASAP if one goes down so I can swap them out with minimum delay. UPDATE 26th June 2013 ------------------------ None of the software that ships with the Supermicro X9SCM-* motherboards offer support for RAID monitoring. As has been pointed out here, these boards are built on an Intel chipset for RAID and so I installed Intel Rapid Storage Technology that supports automated email notifications on RAID failure http://www.intel.com/support/chipsets/imsm/sb/cs-020784.htm One small issue, the software only allows you to send email notifications without SMTP authentication. There's a bunch of different workarounds here: http://communities.intel.com/thread/30771

  Read the article

• Network card shuts down when stressed

  - by user142485

  I have a network card that functions fine with light use, but quits functioning after heavy use. I replaced it with a brand new one and still have the same issue, also updated drivers. It is a wired D-Link card. The Internet seems fine for a small amount of web browsing but when I run a bandwidth test it starts out fast and slows quickly until the card completely quits; I have a constant ping of the gateway going while I run this and it starts timing out after a couple seconds into the speed test. The card will stay on and the data light on it still flashes some but I cannot ping the gateway or anything else until the computer is rebooted. When I boot into safe mode I can browse and run the speed test fine with no problems. I am guessing that this is probably some program that is loading in regular mode but not safe mode that is causing the issue? I have very limited software (turned off av and firewall) on the computer but I am thinking that I'll just have to start eliminating start-up programs and see if that helps. This is on Windows 7 if that makes any difference. Anyone had a similar issue or have any other suggestions/ideas for narrowing down this problem?

  Read the article

• What is the fall off of subsecond throughput on Ethernet Network Interfaces

  - by Kyle Brandt

  On a network interface, speeds are given in term of data over time, in particular, they are bits per second. However, in the uber-fast world of computing -- a second is kind of a really long time. So for example, given a linear falloff. A 1 GBit per second interface would do 500MBit per half second, 250Mbit per quarter second etc. I imagine at certain units of time, this is no longer linear. Perhaps this is set by ethernet frequencies, system clock speeds, interrupt timers etc. I am sure this varies depending on the system -- but does anyone have more information or whitepapers on this? One of the main reasons I am curious is to understand output drops on interfaces. Even if the speed per second is much lower than the interface can handle -- perhaps there are spikes that cause drops for only small numbers of milliseconds. Perhaps various coalescing would hide this effect -- or perhaps increase it on the receiving interface? Do queues make a difference here? Example: So given if this is linear down to the MS we would have 1Mbit/MS, and if Wireshark isn't distorting what I see, should I see drops when I have a spike beyond 1Mbit?

  Read the article

• Many clients on a wireless AP for UDP broadcast packets

  - by distorteddisco

  I asked this question on StackOverflow and was directed over here, so I'd appreciate any advice. I'm deploying a smartphone application as part of a live music performance that depends on receiving UDP broadcast packets from a wireless access point. I'm guessing that between 20 and 50 clients will be connected at any one time. I'm aware that a maximum of 20 clients per access point is advised, but as the UDP broadcast packets are ground through the LAN, how would I be able to link multiple APs together? I'm looking for recommendations on a suitable AP for this. The actual data transmission rates are very low - only a few kB/s - as I'm just sending small messages to the smartphone apps, and there will be no WAN internet connection. I tried it with a few connected peers on an adhoc wireless connection without any problems, but ran into dropped packet issues on an old WRT54G running ddwrt, though it's in pretty rough shape. What's the best way to do this? I suppose I could limit concurrent wireless connections to 20 clients... but more would be nice. EDIT: I should also say that it's purely one-way communication; the smartphone application is only receiving broadcast packets, not sending anything.

  Read the article

• Router as primary DNS server, Server as alternate? (or vice versa)

  - by Jakobud

  We have a very small business network, with a typical cable modem hooked into a DD-WRT router. We also run a basic CentOS server that does a variety of things, including acting as the primary DNS server for the office. The reason we need an internal DNS server is because we do a lot of internal web development and use the DNS server to add/remove various local network URLs for internal website testing (like www.testsite.com.local). It's very important for us to be able to add/remove URL aliases easily to the DNS. The problem with this setup is that if we ever need to restart the CentOS server or take it offline for upgrades or whatever, then internet access for all computers on the network is lost. That's because each computer relies on that DNS server to access the Internet I guess? The router is online all the time and very very rarely has to be restarted. It would be nice if we could setup my router to be the primary DNS server but still be running DNS on my server. So we could still add my local testing website URLs to the DNS server in CentOS, but be able to also take down the CentOS server without loosing Internet access on the network. How would this be setup? Would I simply need to add both router + server IP addresses to each computer's IP settings? Is the router primary DNS and server secondary DNS server? Or vice versa? Or can one of the two serve as a fallback for the other? What (if anything) needs to be configured on both the router and server in order for them to recognize that the other DNS server exists on the network? Does anyone have any newb-friendly resources for setting up something like this?

  Read the article

• Network bandwidth usage dashboard?

  - by SkippyFlipjack

  I have a couple of wifi access points hooked up to my home network, one of which I keep unsecured for some development I do; there are only a couple other homes within range and they've got their own wifi so it's not a big concern. I also have a Sonos system, Tivo, Roku, a couple laptops, a couple phones, an iPad and a desktop machine, all of which are internet-smart. So when my internet bandwidth tanks and it takes five minutes to load a YouTube video, I want to know what's going on, and there are many potential culprits. I'd like to be able to plug my MacBook into the primary router and see a nice little dashboard of the units on the network and what kind of bandwidth each is using at that moment. I could figure this out from WireShark or tcpdump but figure there has to be an easier way. I've tried a few different commercial products but none really presented the right info. Suggestions? (This may be a question for superuser since my Apple Time Capsule's SNMP capabilities are limited, but I figure admins of small business networks would have dealt w/ the same issue..)

  Read the article

• What causes this sonar sound on OS X?

  - by Richard Metzler

  Both of my Macs play this sonar sound that sounds like "ping ping ping ping" with a small amount of delay / echo. It occurs to me that it is played once a day but I'm not sure why. I checked iCal but didn't found anything (I don't use iCal anyways but maybe it's connected to Google calendar or my iPhone). I've heard this sound played by both my MacBook and my iMac but not yet simultaneously. Update This sound is not submarine.aiff. It sounds much more like what skub linked to but there are 4 "pings" instead of 1. It is played at different times (today around 5pm and again at 8.45, but as far as remember not everyday). That's why I'm not sure I could record it, but I could try. The sound might come from my iPhone, though I'm not sure which apps are alowed to play sound when they are not running. Also I don't see any indication in the message center or something similar. I think I have to start taking notes on which apps running.

  Read the article

• AMD processors witn graphics card bundled [closed]

  - by shybovycha

  Sorry for posting this question here - just don't know to which StackExchange website i should be writing. I've heard AMD created processors with video card bundled. So now these processors should work as fast as just usual processors with discrete video card but AMD's ones should use less power and spread less warm. Some googling around gave me the result like "AMD processors of A-series". They were mentioned to be build using that technology i described above. But on the other hand, we have a small rate of publishing and not-very-good quality of AMD drivers. I am a game-developer and web-developer so i need a powerful processor and graphics card and a lot of RAM on board (to make it possible to create a sample Grails application, for example or to create some 3D models in Maya/Cinema4D, for instance). Still i want my battery to be a long-living one, so power usage is a bit critical for me. So, my questions are: are there any processor building technology like i've described and which series they are (if they exist)? which processor shall fit the laptop the best: AMD one or i5/i7 on with nVidia graphics card for the purposes mentioned above?

  Read the article

• customer wont provide ssh access - ftp only

  - by Max

  Eh, here is my problem: I am working in a webdevelopment agency (thats a problem but not the real problem, read on). Most of the time I choose the live server myself when creating a new website project. But now the customer already has a "server" (10 GB on a cheapo host!) and the "admin" refuses to give me ssh access to it. But I need to access the server via shell because many files will be transported (need to be able to upload and extract a tar) and I need to insert or create mysql dumps via command line. He argues FTP and phpmyadmin should be enough... as far as I know the webspace was just ordered to host the website, so no security critical apps are running there. How can I either convince the admin to give me the ssh login or tell management that we need our own server? Anyone with similiar experiences? This is really annoying as this is a very small project that should be done fast and now one has to fight in order to just get the work done...

  Read the article

• Getting PAM/user info into php - something like Net_Finger instead of a db?

  - by digitaltoast

  I've got a very small user group who just need to login, upload, check and then move specific files to a different area when ready. Right now, I use the nginx PAM auth module to log them in against their unix accounts. As their login is their home directory, I've already got the info to send the uploads to the right area - one line of php and no database needed. But I'm maintaining a separate DB just so PHP can welcome them, grab their email and send them an email when processed. Yes, sure I could use nosql or sqlite instead so as to not need a whole mysql install. But it occurred to me that as I've got all these blank user fields for phone numbers I could populate with any data, that I could use something like php's Net_Finger. Which failed for me with: sudo pear install Net_Finger Starting to download Net_Finger-1.0.1.tgz (1,618 bytes) ....done: 1,618 bytes could not extract the package.xml file from "/build/buildd/php5-5.5.9+dfsg/pear-build-download/Net_Finger-1.0.1.tgz" Download of "pear/Net_Finger" succeeded, but it is not a valid package archive Error: cannot download "pear/Net_Finger" At which point I thought I'd stop, and take a ServerFault reality check - is this a really bad/dangerous/stupid idea just to stop me having to maintain details in two places rather than one? It there a better way? Googling shows that it's not an oft-asked thing, so perhaps with good reason?

  Read the article

• Best way to restrict access to a folder in Dropbox

  - by Joe S

  I currently run a business with around 10 staff members and we currently use Dropbox Pro 100GB to share all of our files. It works very well and is inexpensive, however, I am taking on a number of new staff and would like to move the more sensitive documents into their own, protected folder. Currently, we all share one Dropbox account, I am aware that Dropbox for teams supports this, but it is far too expensive for us as a small company. I have researched a number of solutions: 1) Set up a new standard Dropbox account just for use by management, which will contain all of the sensitive documents, and join the shared folder of the rest of my team to access the rest of the documents. As i understand it, this is not possible with a free account, as any dropbox shared folder added to your account will use up your quota 2) Set up some sort of TrueCrypt container, and install TrueCrypt on each trusted staff member's machine, and store the documents inside that. Would this be difficult to use? I'd imagine the sync-ing would not work so well as the disk would technically be mounted at the time of use and any changes would be a change to the actual container rather than individual files. I was just wondering if anyone knows a way to do this without the drawbacks outlined above? Thanks!

  Read the article

• Creating a private wiki

  - by Hand-E-Food

  I want to create a simple, private wiki, but am really struggling to find what I need. I require the following features: Private wiki. Only I will read or write it. Some formatting capability: headings, bold, italic, bullets, block quotes Wiki Viewer for Windows 7. If it comes with an editor, I need to be able to hide it. Page Editor for Windows 7. Page Editor for iPhone. Synchronize by cloud but available offline in Windows. So far, my research has led me to Markdown language. I can easily edit this as plain text using Notepad++ for Windows and Elements for iPhone. I can sync these files through Dropbox and have them available offline. What I can't find is a suitable viewer for Windows. I'd prefer to steer away from using HTML due to its verbose formatting codes. Can anyone recommend a solution for me? If need be, I'll happy to make a small one-off payment for software.

  Read the article

• How to protect folder privacy against unethical network administrators? [closed]

  - by Trevor Trovalds

  I just need a technical solution for the sake of my group's shared passwords, projects, works, etc. safety. Our network has Active Directory with public/groups/users and NTFS permissions, under a Windows Server 2003 which will soon migrate to Windows Server 2008 R2. Our IT crowd is small, consisting of 2 DBAs, 4 designers, 6 developers (including me), 2 netadmins and (a lot of) tech supporters, everyone has local admin rights. Those 2 network admins weren't the ones who set the network up, they just took the lift recently when the previous ones quit. We usually find them laughing at private contents from users stored in the groups AD, sabotaging documents that don't match their personal tastes and, finally, this week we found out they stole a project we (developers and DBAs) were finishing and, long before, they presented it to the CEO as theirs without us knowing. I'm a systems analyst, and initially my group decided to store critical content, like shared passwords, inside encrypted .zip files. Unfortunately we couldn't do the same to the other hundreds of folders and files, which included the stolen project, because the zipping process would take too long for every update. We also tried an encrypted Subversion repository under SSL, but there are many dummies (~38 atm) involved in the projects that have trouble using TortoiseSVN when contributing, and very oftenly we had to fix messed up updates. Well, I think these two give the idea of what we've been trying to reach. So, is there a practical "individual" protection for our extensive data or my hope can already be euthanized? P.S.: Seriously, at the place where I live/work, political corruption gone the wildest, so denounce related options are likely impracticable. Yet both netadmins have strong "political bond" with the CEO and the President, hence their lousy behavior and our failed delation attempts.

  Read the article

• 4GB Memory Upgrade for Acer Aspire 5102WLMi

  - by Richard Slater

  I have bought a 4GB memory upgrade (2x 2GB PC2-5300 SODIMM) for my Acer Aspire 5102WLMi (Aspire 5100 Series) laptop, I installed the two memory modules correctly however with 4GB installed the laptop refuses to POST. I have tried the following: Tried both 2GB SODIMMs without the other (Worked Fine) Tried the original 512MB SODIMMs (Worked Fine) Tried with original 512MB SODIMM and new 2GB SODIMM (Worked Fine) Tried swapping over the 2GB SODIMs (Didn't Boot) Left the computer for 10 minutes with both 2GB SODIMMs installed (Didn't Boot) Checked latest BIOS installed (No Change) The Crucial website said that the laptop supported 4GB of RAM as do several other sites through found through Google, up until now I was fairly confident this would work. Couple of questions that would be good to have answered: Question: Has anyone got an Acer Aspire 5100 Series running with 4GB RAM? Answer: Yes, I have now got one working with 3.75GB Usable, the rest is occupied utilized by the Graphics Card. Question: Any tips on getting this to work; is there a CMOS reset switch? Answer: Yes there is, if both SODIMMs are removed two very small interlocking PCB tracks are revealed. If these are shorted together with a screwdriver the BIOS will be reset. Thanks.

  Read the article

• LMDE detects a wireless card, but can't use it

  - by Davidos

  LMDE can see my wireless card, and correctly identifies it, but it refuses to let me turn it on through the shiny graphical interface. Is there a way to use the non-shiny terminal to turn on my wireless? One small tidbit I noticed was the stated version; it says the version is 00. I believe that's hexadecimal for 0, which may indicate something screwy with the software. It would be nice if someone could tell me how to figure out how to solve this kind of problem in the future. *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 00 serial: 91:e3:7b:0d:a3:a9 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-1-amd64 firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:43 memory:e1d00000-e1d01fff I've tested multiple other network managers, and none of them work. W ireless switch is on, I'm sure it's a driver problem.

  Read the article

• How to change font size on display

  - by Tim

  My laptop is Lenovo T400, whose screen size is 14.1 inches and default resolution is 1440 x 900. My main OS is Ubuntu 10.10. The default font size on the display is somehow small, which might contribute to the fatigue of my eyes. My previous laptop is Acer 5000, whose screen size is 15.4 inches and the default resolution is 1024 x 768. I like reading on my old laptop better than on my new one. Is it possible to change the setting of my new one to look like reading my old one? What are the parameters that control the font size? Are screen size, resolution part of them? In Windows, there are choices for font size, while in Ubuntu I haven't find out where I can change the setting and would like know if someone here knows about it. I also wonder if I can use a separate bigger display (perhaps just like a desktop display) as the display of my laptop, in case I don't want to enlarge font size at the cost of sacrificing the amount of the content to display, and how I shall do it? Thanks and regards!

  Read the article

• thought about shared storage (NFS, Lustre) [closed]

  - by user134880

  Possible Duplicate: Can you help me with my capacity planning? Now I habe small cluster with total of 8 nodes. 6 of them are computing nodes (apache and vmware) and 2 nodes are for storage. 2 storage nodes are identical. Each storage server is linux box with 8 x 1Tb WD RE4 in soft raid 10. 1st box is master and 2nd is slave. Data is mirrored with DRDB. We export NFSv4 shares to Apache (for document root) and iSCSI to Vmware. Now all is working pretty good and stable. But it will be soon time to upgrade our system. I have been thinking of Lustre. Does some one has any real experience with Lustre or NFS medium clusters? Will it be good idea just to upgrade server and change hdd's to 3Tb ? With NFS we will always have only 2 servers to maintain (one primary and one slave). Thanks. QUESTIONS: 1) Does some one used Lustre? In production? I have seen a lot of info about how it is hard to setup Lustre because you need to compile own kernel and patches. It's answers from newbies. Is there some one who has used Lustre for some period of time? 2) About disk upgrades - it's only description of strategy. I'm not asking if it is enough 3Tb or not. I just ask if it is right just to replace hdds instead of adding new server (like with Lustre) Thanks again.

  Read the article

• Server taking too long to respond error

  - by DCJones

  Hi, This is my first post on serverFault and my first entry in to web server configuration. The hardware and software. CPU: GenuineIntel, Intel(R) Core(TM)2 Duo CPU E7500 @ 2.93GHz OS: Linux 2.6.18-128.el5 Memory: 2Gb Background. I am running a small database (MySQL), around 1000 records with each record containing 44 fields. At the start of each day “00:01” the tables are cleared and populated with fresh data. The are 10 remote PCs all running Winodws XP and Firefox internet browser. All remote PC’s are connected to the internet using a min 4Gb broadband connection. Each remote PC runs a URL which displays a dynamic page of data which is refreshed every 20 seconds. This is a continual process 24 hours a day. I problem I am having is on odd occasions throughout the day the PC browser error with “Server taking too long to respond error”. What I am trying to find our is if I have the correct setting in the httpd.conf file on the server. Any help or advice anyone can provide would be very helpful. Best regards Dereck Server config file: httpd.conf ServerRoot "/etc/httpd" PidFile run/httpd.pid Timeout 120 KeepAlive On MaxKeepAliveRequests 200 KeepAliveTimeout 5 StartServers 8 MinSpareServers 5 MaxSpareServers 20 ServerLimit 256 MaxClients 254 MaxRequestsPerChild 4000 StartServers 2 MaxClients 150 MinSpareThreads 25 MaxSpareThreads 150 ThreadsPerChild 25 MaxRequestsPerChild 0

  Read the article

• Is it possible to add a WiFi HotSpot to an already established LAN, keep the two separate, and not modify the primary router?

  - by user12844

  I have a set up where my Cisco ASA is sitting in one facility, providing access to the Internet for two buildings. The two buildings are geographically separated by a Wireless Bridge spanning about 10 miles. All computers and equipment inside the LAN are on the same subnet (its pretty small) and we have WiFi AP's in both locations providing Wired and Wireless access to the LAN. Given all the BYOD (Ipods, and SmartPhones etc...) coming into the office as well as Visiting reps etc... we would like to also provide a non-secure, device independent (the devices cannot see or communicate with each other), and LAN independent (the devices cannot see or use anything on the LAN) HotSpot that anyone could use for their Devices that gives them access to the Internet ONLY without needing a password. I get that this could be possible at the facility with my Cisco if I messed with it and created VLANs etc... but then I would need to get it across my Bridge as well and don't think that would be possible without serious reconfiguration of everything. Would really like some kind of magic drop in solution that can kind of piggy back on my LAN without really needing to do very many if any changes to the current set up.

  Read the article

• Reading log files from web application

  - by Egorinsk

  Hi! I want to write a small PHP application for monitoring logs on a Debian server, including syslog logs and Apache/PHP messages. The problem here is that Apache user (www-data) has no access to /var/log directory. What would be the best way to grant an access to logs for PHP application? Let's assume that log files can be really large, like hundreds of megabytes. I have some ideas: Write a shell script that would be run via sudo and tail last 512 Kb of log into a separate file that can be read by application - that's ineffective, because of forking a new process and having to read data twice Add www-data to adm group (that can read logs) - that's insecure Start a PHP process via cron every minute to read logs — that's not very good, because it doesn't allow real-time monitoring. Also, this script will be started even when I don't read logs, and consume CPU time (server is in the cloud, and I'll have to pay for it) Create a hardlink for all log files with lowered permissions - I guess, that won't work because logrotate could recreate log files and they'll change inode number. Start a separate nginx/Apache server under privileged user that may read logs. Maybe anyone got a better solution?

  Read the article

• Booting Windows from different partition than system

  - by szamil

  I have bought an SSD disk, but my laptop (Dell Precision M6300) refuse to use it as a target disk for windows (AHCPI on/off, BIOS up-to-date). I can't exchange the disk unfortunately... But fortunately, I've managed to install windows using USB disk case. The problem is, that when I put that disk as my internal drive it can't boot. (Disk read error, Three Finger Salute ... ) So I tried with Linux (openSUSE), I manage to install it as well, but when I tried to boot GRUB from internal drive I get errors again. (Should I try GRUB2?) I figured out that I can boot into that internal hard drive's openSUSE system using small USB drive with GRUB, kernel and image on it. So, I just run GRUB from USB drive, it loads necessary stuff from the USB drive and then continues from the internal drive. I want to do the same with Windows. But GRUB (rootnoverify and chainloader +1) does not boot my windows on internal drive. The question: is there any chance to copy the critical windows' boot files into the USB drive, to make it possible to boot from that USB drive, but continue booting from internal (different in general) drive? The USB drive would became a system hardware key! ;-) Disk: Plextor M5S 128GB Sata III, laptop has Sata II, but it's compatible anyway, right?

  Read the article

• How to fix Windows 7 device removal notification loop

  - by Barry Kelly

  Bit of an odd one this. One of our PCs is getting caught in a loop some time after being turned on, usually after a USB storage device has been attached - sometimes an iPod, sometimes a GPS. Specifically, Windows Explorer starts showing a drive icon and letter (E:, as of right now) for the System partition (the small hidden one at the start of the boot drive). Then, the icon disappears. Then it reappears again. And disappears. It does this very quickly, at what looks like maybe 50 times a second. CPU usage in this loop is also very high; averages about 66%. This machine has an i7 920 CPU, which is quad core with hyperthreading; so this usage rate works out to about 5 100% busy threads, along with whatever normal idle load is (particularly Task Manager itself). Inspecting with Process Explorer shows that the device removal notification infrastructure has gone berserk. The threads in system service processes (i.e. apart from Windows Explorer) which are using all the CPU power relate to device notification. The Disk Management MMC snap-in also fails to run when the loop starts. The only way to break the loop, it seems, is to reboot the machine. Anyone seen anything similar to this, and know of a way to fix it? Machine details: Windows 7 x64, fully patched i7 920, 12GB RAM Intel SSD 80GB (X25-M, I believe; not G2) 2TB 5.2K disk for bulk storage AMD HD 5870 Further hardware details await. I'm going to go through and update all drivers I can find.

  Read the article

• Wires from fan on side panel - where do they connect?

  - by Mick

  The side panel of my desktop PC has a small fan built in. There were two wires, one red one black that connected inside the PC. Unfortunately I had the bolts removed and the side door fell off ripping the cables such that the main length of cable remains attached to the fan. So there must be two short stubs of broken cable somewhere - but I can't find them! Any ideas where I should look? I can't see anything on the motherboard. the PC is running perfectly well - but I now have the side open to make sure the air can circulate. EDIT: The motherboard appears to be an "Asus P6T SE" EDIT: The manual shows the location of two "chassis fan" connectors. One is being used by a big chassis fan on the back face of the PC (underneath the pwer supply). The other appears to be unused - there is no stub of a connector with wires - its just the bare pins sticking directly out of the motherboard. There is also an unused "pwr_fan" connector. Would it be ok to simply connect the black and red wires from the fan to the black and red parts of a molex adapter?

  Read the article

• Confused with creating an ODBC connection, apparently I have two separate odbcad32.exe files?

  - by Hoser

  Alright, this is my first time working with this so forgive me if I'm a little confusing or vague. I have a server with Windows Server 2008 Standard without Hyper-v (6.0, Build 6002). I'm running a small website off this server and using a Microsoft Access database to store some information coming in through the website. I'm sure the PHP I have written to open the ODBC connection is correct as it has worked for me when I created this website in a testing environment on a laptop. My current issue now is that it seems like I have two different odbcad32.exe's, and one doesn't appear to have a driver for a .accdb file, and only a .mdb file. The other has a driver for both. The first one I speak of has a driver titled 'Driver do Microsoft Access (.mdb)', the second one has a driver titled 'Microsoft Access Driver (.mdb, .accdb)'. I access the first odbcad32.exe by going to C:\Windows\SysWOW64\odbcad32.exe, and then the one that seems to have the driver I need I go to Control Panel-Administrative Tools-Data Sources(ODBC) and simply create a new connection in the System DNS tab. Whenever I make changes to the one that I access through the Control Panel, I see no changes, however if I use the odbcad32.exe file in SysWOW64 I do get some changes in the errors that come back to me. The main difference I noticed is that when I set up an ODBC connection with the Control Panel method it said it simply couldn't find the ODBC connection, but when I made a .mdb connection in the SysWOW64 one (and pointed it to a .accdb file) it says Cannot open database '(unknown)'. It may not be a database that your application recognizes, or the file may be corrupt. Which makes it seem like it is this odbcad32.exe version in SySWOW64 that is being recognized as the 'correct' one. Is there any way to fix this? I've tried to be as thorough as possible but if I've been confusing or left anything out let me know.

  Read the article

• PHP Web Server Solution (Apache/IIS)

  - by njk

  I apologize if this is too broad or belongs on Super User (please vote to move if it does). I'm in the process of creating requirements for an internal PHP web server to submit to our architecture team and would like to get some insight whether to use a Windows or *nix platform and what applications would be required. The server will host a small PHP application that will be connecting to SQL Server. The application will need to send mail. We would also like to incorporate a FTP server to allow files to be dropped in. From what I've read regarding a Windows platform using IIS, it seems as though IIS would only be advantageous if using a .NET or ASP application. Does IIS have mail functionality? Or how is mail traditionally configured (esp. on *nix)? Also, does IIS have directory configuration functionality like Apache does with .htaccess? For a Windows based solution; IIS (comes with FTP) Apache (has mod_ftp module) For a *nix based solution; Apache

  Read the article

< Previous Page | 375 376 377 378 379 380 381 382 383 384 385 386  | Next Page >