Search Results

Search found 2177 results on 88 pages for 'wifi'.

Page 38/88 | < Previous Page | 34 35 36 37 38 39 40 41 42 43 44 45  | Next Page >

• iwlwifi on lenovo z570 disabled by hardware switch

  - by Kevin Gallagher

  It was working fine with windows 7. The hardware switch is not disabled. I've toggled it back and forth dozens of times. The wifi light never turns on and it always lists as hardware disabled. I have the latest updates installed. I've been searching for solutions, but none of them seem to work for me. I've tried removing acer-wmi. I've tried setting 11n_disable=1. I've tried resetting the bios. I've tried using rfkill to unblock (only removes soft block). I've rebooted dozens of times. The wifi light turns off as soon as grub loads. Edit: I have a usb edimax wireless nic. It shows hardware disabled as well (although rfkill lists as unblocked). If I unload iwlwifi the usb nic works fine. uname -a `Linux xxx-Ideapad-Z570 3.2.0-55-generic #85-Ubuntu SMP Wed Oct 2 12:29:27 UTC 2013 x86_64 x86_64 x86_64 GNU/Linu`x rfkill list 19: phy18: Wireless LAN Soft blocked: no Hard blocked: yes dmesg [43463.022996] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [43463.023002] Copyright(c) 2003-2011 Intel Corporation [43463.023107] iwlwifi 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [43463.023190] iwlwifi 0000:03:00.0: setting latency timer to 64 [43463.023253] iwlwifi 0000:03:00.0: pci_resource_len = 0x00002000 [43463.023257] iwlwifi 0000:03:00.0: pci_resource_base = ffffc900057c8000 [43463.023261] iwlwifi 0000:03:00.0: HW Revision ID = 0x0 [43463.023797] iwlwifi 0000:03:00.0: irq 43 for MSI/MSI-X [43463.024013] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [43463.024250] iwlwifi 0000:03:00.0: L1 Enabled; Disabling L0S [43463.045496] iwlwifi 0000:03:00.0: device EEPROM VER=0x15d, CALIB=0x6 [43463.045501] iwlwifi 0000:03:00.0: Device SKU: 0X50 [43463.045504] iwlwifi 0000:03:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [43463.045542] iwlwifi 0000:03:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [43463.045744] iwlwifi 0000:03:00.0: RF_KILL bit toggled to disable radio. [43463.047652] iwlwifi 0000:03:00.0: loaded firmware version 39.31.5.1 build 35138 [43463.047823] Registered led device: phy18-led [43463.047895] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [43463.048037] ieee80211 phy18: Selected rate control algorithm 'iwl-agn-rs' [43463.055533] ADDRCONF(NETDEV_UP): wlan0: link is not ready nm-tool State: connected (global) - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: unavailable Default: no HW Address: 74:E5:0B:4A:9F:C2 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points lshw -C network *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 [Condor Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 74:e5:0b:4a:9f:c2 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-55-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:43 memory:f1500000-f1501fff lspci 03:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak]

  Read the article

• Wireless is disabled by hardware switch on Dell Inspiron 1750

  - by lowerkey

  I have a problem where Ubuntu (12.04) says there is a wireless network card, but it is disabled by a hardware switch. How do I turn it on? I checked the BIOS, and the wireless card is enabled there. Fn + F2 was also no success. The results of rfkill list: 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes sudo rfkill unblock wifi did nothing to the Wireless Status.

  Read the article

• Toshiba wireless is blocked

  - by zorrillo

  I have the same problem, a 32 bits toshiba nb255, it first had the windows 7 bu next I installed the ubuntu 11.04. The wifi does not turn on. I used the following issues the commands rfkill unblock wlan0, sudo ifconfig wlan0 down; they were not able. by setting up the bios in advanced menu, the wireless communication sw in ON, but it did not work also. neither the utilities toshiba nor utilities of ubuntu (wicd, wifi radar). by using gedit to file group, nothing. by installing madwifi packet, nothing. by exporting the wifi driver from windows to ubuntu, by means of the NDISwrapper packet, neither. I put the current scripts of the ouput of the cli root@zorrillo:~# rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes root@zorrillo:~# sudo lspci | grep Atheros 07:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) root@zorrillo:~# root@zorrillo:~# ifconfig -a eth0 Link encap:Ethernet direcciónHW 88:ae:1d:47:df:e1 ACTIVO DIFUSIÓN MULTICAST MTU:1500 Métrica:1 Paquetes RX:0 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:0 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:0 (0.0 B) TX bytes:0 (0.0 B) Interrupción:43 Dirección base: 0xe000 lo Link encap:Bucle local Direc. inet:127.0.0.1 Másc:255.0.0.0 Dirección inet6: ::1/128 Alcance:Anfitrión ACTIVO BUCLE FUNCIONANDO MTU:16436 Métrica:1 Paquetes RX:8 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:8 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:0 Bytes RX:480 (480.0 B) TX bytes:480 (480.0 B) ppp0 Link encap:Protocolo punto a punto Direc. inet:189.203.115.236 P-t-P:192.168.226.1 Másc:255.255.255.255 ACTIVO PUNTO A PUNTO FUNCIONANDO NOARP MULTICAST MTU:1500 Métrica:1 Paquetes RX:6384 errores:30 perdidos:0 overruns:0 frame:0 Paquetes TX:6893 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:3 Bytes RX:5473081 (5.4 MB) TX bytes:974316 (974.3 KB) wlan0 Link encap:Ethernet direcciónHW 00:26:4d:c3:d0:44 DIFUSIÓN MULTICAST MTU:1500 Métrica:1 Paquetes RX:0 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:0 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:0 (0.0 B) TX bytes:0 (0.0 B) note.-it is logical all the counters are cero if the wireless device is down root@zorrillo:/home/zorrillo/Descargas/802BGA# ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill root@zorrillo:/home/zorrillo/Descargas/802BGA# It would seem the wireless switching does not react with whichever ubuntu 11.04 command (I hope to be wrong). The target remains the same, in order of the scripts above. I am worried, I have tried to find any answer for days and nights. Toshiba does not supply drivers or soft support for linux, marketing of course. I only see the device is up by protocols and down phisically, My question is, is it possible to enable or not shutdown physically the device?, because in the toshiba model nb255 the wifi is not set up/down bye means of a physical switch, but by means a combination of Fn + F8 (only for windows 7, no one more), Is there one possibility to configure the hot keys in ubuntu?

  Read the article

• Can't ping devices by IP address for devices allocated IPs by DHCP

  - by GiddyUpHorsey

  I have a home network with a Trendnet wireless router and a Windows Domain. The Domain Controller/DNS server is a Windows 2000 Server and is configured to forward queries to DNS servers provided by the ISP. The router provides DHCP and is configured with the Windows 2000 Server as the DNS server. The network has been set up for a couple of years and usually works fine. When I connect iPhones to the network over WiFi, the router can ping the iPhones through its browser based admin interface, but Windows machines that are part of the Windows Domain cannot. A laptop was connected to the network over WiFi that wasn't joined to the domain and it could see the iPhones. The router UI shows that the laptop has a reserved IP allocated via DHCP. All machines either have a static or DHCP allocated IP on the 192.168.0.* subnet. Router - 192.168.0.1 - Static - Wired Windows Domain Controller - 192.168.0.8 - Static - Virtual Windows 7 Workstation - 192.168.0.200 - DHCP Auto - Wired VMWare ESXi Host - 192.168.0.201 - Static? - Wired iPhone 1 - 192.168.0.202 - DHCP Auto - WiFi iPhone 2 - 192.168.0.203 - DHCP Auto - WiFi Windows Vista Laptop - 192.168.0.204 - DHCP Reserved - WiFi Using the Windows 7 machine (200), I try to ping each machine and the only DHCP machine that responds is itself. The other DHCP machines fail with Reply from 192.168.0.200: Destination host unreachable.. Using nslookup fails with *** domain.controller.name can't find 192.168.0.203: Non-existent domain. Using the Windows 2000 Domain Controller (8), I try to ping each machine and the only DHCP machine that responds is the Windows 7 machine (200). Pinging the other DHCP machines fails with Request timed out.. Using nslookup also fails with *** domain.controller.name can't find 192.168.0.203: Non-existent domain. Using the iPhone 2 (203), I try to ping (Network Ping Lite) the machines with static IP addresses and that works fine. When I try to ping the Windows 7 machine (200) it is unable to get a response. How do I configure the DNS server/Windows Domain/Router properly so that the Windows Domain machines can see the IPs allocated via DHCP?

  Read the article

• Limit bandwith on network of computers

  - by Joseph34123

  We have network in office of approximately 10 computers sometimes when someone downloads something for work (e.g. syncing email with an attachment or Dropbox), everyone slows down. I could limit each computer in office but the problem is that we have an open WiFi network, and I cannot access the computers that use it. We have one main DSL router "Netopia 3347" and another router connected to it on wire for public wifi is "Linksys WRT110". I cannot change the setup we have and don't want to. There's 2 approaches here: Set office computers download limit in each computer and then I need to find out how I can set a download limit for the wifi network such as in the router settings. It's a Linksys router and I did not see the option for this, so maybe I need new router for WiFi? Don't bother with each computer and put some "specific hardware" or another computer before router so all traffic goes trough it and I can then assign priority maximum speed for each IP address. Question is what hardware do I need?

  Read the article

• How to use the AWUS036H on MacBook Pro with Lion and Backtrack in VM?

  - by Swader

  I have the AWUS036H USB WiFi adapter and have recently upgraded the OSX to Lion. The thing is, there are no drivers for Lion for the AWUS036H, and I would have to boot into 32bit mode every time I want to launch the adapter as per instructions here: http://www.youtube.com/watch?v=n9_HAGi1ce0 I also want to install BackTrack as I deal in networks a lot for my company. While this would be a simple matter on any other laptop, the company issued Macbook does not allow booting into any OS other than MacOSX or Windows with Bootcamp. Now, since dual booting into BT is not an option, I would like Backtrack to run in VM inside my MacOSX Lion - and this it does. It works like a charm inside VirtualBox. But since there are no 64bit drivers for the wifi adapter, Lion doesn't recognize it and cannot install it. This, in turn, means that Backtrack cannot see it even though AWUS036H usually works flawlessly with BT. How can I make my VM-based BT see the wifi adapter even if the parent OS doesn't see it, if at all? Is there a way, or am I better off buying a new WiFi adapter that supports OSX 10.7 such as the AWUS036NHR?

  Read the article

• Configuring network route between two routers on home network

  - by Paul

  I have a home network - the main router connected to the internet (and has wifi) is a Netopia box. Connected to it is a Linksys router. Everything currently works - I can connect via the wireless network and get to the internet. Machines connected to the Linksys can connect with each other and connect to the internet. Both routers are configured to serve addresses via DHCP (Netopia 192.168.1.1 - 192.168.1.99), Linksys (192.168.0.1 - 192.168.0.100). Here's how they are connected: Internet <-> Netopia w/wifi (192.168.1.254) <-> Linksys (192.168.0.1) I decided I really need to allow wireless connections to also communicate with machines behind the Linksys router. Currently the Linksys is configured to obtain an IP address via DHCP. I thought this would be straightforward. I configured the Linksys to have a static IP address: IP: 192.168.1.100 Mask: 255.255.255.0 GW: 192.168.1.254 Then I configured a static route on the Netopia: Network: 192.168.0.0 Mask: 255.255.255.0 GW: 192.168.1.100 So it should now look like this: Internet <-> Netopia w/wifi (192.168.1.254) <-> (192.168.1.100) Linksys (192.168.0.1) I reset both routers. I cannot ping the Netopia (192.168.1.254) from inside the Linksys network, and if I attempt to ping 192.168.0.1 from a wifi connection I get a "Destination host not available" error. Obviously I'm missing something, but I'm not sure where. Any ideas on what I'm missing?

  Read the article

• All application passwords lost on Windows 7

  - by Rynardt

  A couple of days ago I changed my Windows 7 login password. My laptop is on my company's domain, so password changes are done over the internal network. Since changing the password I noticed that all my saved Chrome passwords are missing. Also Skype, Windows Live, Internet Explorer and Outlook lost their saved passwords. I guess there could be more applications with lost passwords, but I have not opened them yet. This makes me think that most applications saves their passwords to a general password vault on the Windows system and this vault got somehow corrupted when I changed my domain login password for windows. Do anyone have any idea of how to fix this and prevent it from happening again? EDIT : More Info I do development work at the office, so most of the time I bypass the firewall and connect directly to the internet gateway. Now and then I would connect to the company wifi network to do printing and access files on a NAS. So by default my laptop does not connect to the wifi hotspot. On this occasion to update the password, I had to connect to the wifi. So referring to the comment by OmnipotentEntity below, could this have happened when the system rebooted without a connection to the network as the laptop does not auto connect to the wifi hotspot?

  Read the article

• cannot ssh to computer behind a dd-wrt bridge

  - by Jayaraman

  In my home network , i have dd-wrt router in another room , which bridges wifi from main home router (linksys) to the computers wired behind dd-wrt router. Now I cannot ssh from my laptop ( connected to linksys wifi) to the computers behind dd-wrt wifi bridge. I am able to ping the individual computers behind the dd-wrt bridge. When it comes to ssh or telnet to the computers , it is blocked. What can I do to make dd-wrt bridge to open up all ports in the dd-wrt bridge ?

  Read the article

• How to roll-your-own live CD for safe home browsing

  - by user36533

  Hi, I'm interested in booting-off-flash (i.e. like livecd) for more secure online banking at home. -I like system rescue CD, but AFAIK it doesn't have the wifi drivers. (These are convenient) -ubuntu live cd has the wi-fi drivers, but also has a lot of stuff I don't need -I'd like a way to save some basic config settings (e.g. wifi SSID and passphrase), so that wifi works upon startup, i.e. without having to re-enter the settings. What's the best way to 'roll my own slightly-customized boot-from-flash live cd? thanks, bill

  Read the article

• How to emulate wireless in Virtualbox?

  - by huahsin68

  I have WinXP install in virtualbox which host in Linux. I have a TP-Link (TP-WN321G) USB wifi adapter and have the driver installed inside WinXP. When I plug-in the wifi adapter, there is an option show "Ralink 802.11g WLAN [0101]" in the virtualbox's USB icon, tick on that option, the Device Manager able to detect the hardware which shows TP-Link, but when look into the properties, it says there is no driver was install. I did try to install Ralink driver but still no luck. Just curious why my wifi adapter is TP-Link, but the option show Ralink? May I know how can I emulate the wireless network inside WindowsXP?

  Read the article

• Thinking of Powerline adapters for networking

  - by Henderson McCoy

  will powerline work as good as wifi I am now in a large house (renting a room) and the router is in the front of the house and I am in the back. Don't know if wifi will have the range and stability so I am looking at all the alternatives from running a long cable to powerline. looks like a powerline adapter set will cost about $50 http://www.bestbuy.com/site/Actiontec---500-Mbps-Powerline-Home-Theater-Network-Adapter-Kit/5215483.p?id=1218625358741&skuId=5215483 has anyone use these or other powerline adapters? how is powerlines speed? Are they more stable then wifi? powerline cost is good i am just currious about the performance

  Read the article

• Share laptop Wi-Fi with router set up as access point via ethernet cables

  - by obie

  I have an ADSL modem which serves as a wireless router. There's a laptop connected to it through cable. On the other room I have a laptop which is connected through the router wirelessly. Since I have other appliances that need to get connected but are not Wi-Fi capable I have another Wi-Fi router. How can I share the second laptop's Wi-Fi with the second router so that the router can then serve as an access point to give internet to my other appliances through ethernet cables? I want something like this: INTERNETMODEM (WIFI)LAPTOP 1 (WIFI)LAPTOP 2 (WIFI)Router 2 (ETHERNET)DREAMBOX & WDTV What I've tried so far is opened the admin interface of router 2 then set static IP 192.168.100.13 and disabled the DHCP. The DHCP of the main router starts with 192.168.100.1 then I hooked up router 2 with the laptop 2 through Cat5 cable but for some reason it's not working.

  Read the article

• What's the point of Netgear's WNHDB3004 "3DHD WIRELESS HOME THEATER NETWORKING KIT"

  - by badp

  Here's a crude representation of what I've got at home: floor 2 INTERNETS ---- MODEM/ROUTER ---- MY COMPUTER | floor 1 WIFI REPEATER ---- stuff | floor 0 more stuff TELEVISION Now, as part of our sat tv subscription we can get an additional service if we connect our decoder (located by TELEVISION obviously) to the internet. What they suggest is buying a Netgear 3DHD WIRELESS HOME THEATER NETWORKING KIT holy shit isn't my bullshit-o-meter flying high right now from the general buzzwordyness of this thing. What does this thing actually do that our existing wireless-enabled routers don't do? What's the point of having a third wifi router in the same house, this time only for one television? If I do decide to plunge €99 for this, should I connect it to the wifi repeater (which does not provide AAA quality internet, at least for all gaming purposes) or to my modem/router (risking issues with low signal?).

  Read the article

• Troubleshooting web timeouts with a Belkin router

  - by rexzilla

  I have a Belkin FSD7632-4 ADSL wifi router. Ever since I got it, I've faced this problem of websites timing out. For example, I go to flickr.com, and the images won't load because they come from farm1.static.flickr.com. Either I wait 10 minutes or so until the timed out sockets are closed and retry (with variable results) or I reboot the router. This happens irrespective of whether I use wired or wifi network. I'm in India, using Airtel Broadband, and if I use my ISP supplied Beetel 220BX ADSL router (which has no wifi and only one LAN port), everything works fine. I copied over the broadband settings from my old router: VPI/VCI values=1/32 Encapsulation=LLC MTU=1492 I have not enabled any firewall on the router. Is there anything else I can try? Or is it a defect with the router and should I take it back for a replacement? I bought it just 2 months ago.

  Read the article

• Mac OS X: pushing all traffic through a VMWare VM [closed]

  - by bj99

  I want to set up an Astaro (Sophos) UTM in a Virtual Machine. The Setup should be at the end the following: Cable Modem (one IP adress) | [Ethernet] Sophos UTM (running as VM [VMWare Fusion 5] on the MacMini) | [WIFI] Airport Express v2 (for sharing Local Network to wireless and wired clients) 1)| [WIFI] 2)| [Ethernet over Thunderbolt Ethernet Adapter]* Clients MacMini (Local File Server) *To have the Mini also protected behind the UTM So the setup process for the UTM works fine, but then the problems start: I just have one external IP (from my cable modem provider)== So if I put the VM in briged mode my Internet connection drops, because the MacMini also has its IP adress. If I put the VM to NAT mode the Mini itself is not protected by the UTM So: is there a way to hide the en0 interface(Ethernet) and the en1 interface (Wifi) from the MacMini, so that they not even appear in System Preferences Network section but are available to the VM? That way the Mini must connect to the en2 interface (Thunderbolt adapter) to make any Internet/LAN connection and I just use the given single IP from the Cable Modem. Thaks for any suggestions... Sebastian

  Read the article

• Random flickering on 2.6.32 kernels after suspend

  - by whitequark

  I have XUbuntu 9.10 installed on a Toshiba NB200 netbook with Intel video card that's handled with i915 driver. With 2.6.31 stable, recommended kernel everything but WiFi works fine: Atheros ath9k WiFi shows too small signal power and loses packets in 'bursts' sometimes. With 2.6.32-* (I tested -9 to -11 from Ubuntu's kernel unstable ppa) everything works fine just prior to first suspend: echo mem >/sys/power/state. After it random unidentified fullscreen 'one-frame' flickering begins in Xorg, and after a couple of minutes everything eventually hangs while showing filled grey (not white; it is like default button colour) screen; no X keys are working: Ctrl+Alt+Fn don't, blind typing in console too. Magic SysRq still works and I was able to reboot. Also there is one out-of-tree kernel module called omnibook that is required to turn on WiFi and Bluetooth. Any advices?

  Read the article

• Can I turn my Mac Mini into a Wi-Fi Hotspot without additional tool

  - by user262325

  Hello everyone I have an app need to test via wifi. I just wonder if there is a way to turn my Mac Mini into a Wi-Fi Hotspot without additional tool. I try to setup airport new network name is"mymacmini'. My iPod Touch also can recognize the network "mymacmini". I set my iPod wifi as "mymacmini" But if I try to connect to Internet, Safari always reports failure and connnection with Wifi. I hope to know if I need purchase a wireless router for MAc Mini or there are something wrong I did above? Thanks interdev

  Read the article

• Taskbar Network "Repair" menu option gone in Windows 7

  - by JohnB

  I used to LOVE that feature in Windows XP! Just right-clicked on the WiFi icon on the Taskbar (lower right-hand corner), then Repair. It doesn't take that long, and it usually helped me since I constantly go back and forth between LAN at work, VPN on WiFi from work and home, and also VPN to my own personal server. Even if you didn't need to refresh, doing so never hurts! Unfortunately, the feature seems to be removed from Win7 :( Now you can check for problems, but it only does the refresh if it thinks it needs too, and the whole process tasks so darn long! Is there a way to Repair my WiFi connection quickly and easily on Win7?

  Read the article

• Ad-hoc connection between iPhone and Macbook Pro

  - by Phil Nash

  I sometimes find it useful to connect my iPhone to my Macbook Pro by creating an ad-hoc wireless network from the MBP and connecting to that from the iPhone. However, what I find is that sometimes this works and sometimes it doesn't. When it's not working the symptoms are usually that I see the ad-hoc SSID in the list of available networks on the iPhone, can connect to it from there (including entering my WEP key), and it shows up as the wifi network in use. However I don't get the wifi symbol in the taskbar (it remains as 3G) and attempting to use the connection (e.g. trying to connect to iTunes or Keynote using their respective Remote apps) fails saying that there is so wifi connection. I've tried rebooting both the iPhone and the MBP, recreating networks with different SSIDs and tried different channels - all to no avail! I'm especially puzzled that (a) sometimes it works just fine first time and (b) the Settings app seems to think its all connected fine. Is there anything else I should be trying?

  Read the article

• Access Methods to a computer Using MAC Address

  - by Dimal Chandrasiri

  I have my own wifi network at home & recently when I checked the active clients on the wifi I found out the there is one active client. Router shows the MAC address of this client and I want to Access this computer in order to let him know that he's doing a wrong thing. I dont intent to do any harm to his data. I just want to know a method to send him a message saying "Buy you own wifi". How can I achieve this using a windows 8 computer. Is there any specific softwares that I can use or will the netsend command do the trick! Thank you.

  Read the article

• Wireless DHCP doesn't work until wired Ethernet plugged in

  - by MT_Head

  A client of mine has an Asus R1F tablet running Windows XP Tablet SP3. It has an Intel 3945ABG wireless card; wired Ethernet is a Realtek something-or-other. In the past few days, it's developed an odd problem: WiFi authenticates, but can't get an address via DHCP. plug in wired Ethernet - both interfaces get good addresses unplug cable, WiFi continues to work until shutdown. Next morning, repeat process. I've tried: turning WiFi off/on (there's a slider switch) disabling/re-enabling via Device Mangler uninstalling and reinstalling the driver for the 3945ABG... changing from Intel Pro/SET to Windows Wireless Zero Config (and back) restarting the router changing the static DHCP assignments at the router upgrading the router firmware, just on general principles The router/access point is pfSense 1.2.3RC1 (was 1.2.2); wireless card is Atheros-based. None of the 12 other users (5 with tablets) are having problems.

  Read the article

• Mac OS X: pushing all traffic through a VMWare VM

  - by bj99

  I want to set up an Astaro (Sophos) UTM in a Virtual Machine. The Setup should be at the end the following: Cable Modem (one IP adress) | [Ethernet] Sophos UTM (running as VM [VMWare Fusion 5] on the MacMini) | [WIFI] Airport Express v2 (for sharing Local Network to wireless and wired clients) 1)| [WIFI] 2)| [Ethernet over Thunderbolt Ethernet Adapter]* Clients MacMini (Local File Server) *To have the Mini also protected behind the UTM So the setup process for the UTM works fine, but then the problems start: I just have one external IP (from my cable modem provider)== So if I put the VM in briged mode my Internet connection drops, because the MacMini also has its IP adress. If I put the VM to NAT mode the Mini itself is not protected by the UTM So: is there a way to hide the en0 interface(Ethernet) and the en1 interface (Wifi) from the MacMini, so that they not even appear in System Preferences Network section but are available to the VM? That way the Mini must connect to the en2 interface (Thunderbolt adapter) to make any Internet/LAN connection and I just use the given single IP from the Cable Modem. Thaks for any suggestions... Sebastian

  Read the article

• Where can I configure wireless to be passed on to the Virtualbox guest?

  - by huahsin68

  I have WinXP install in virtualbox which host in Linux. I have a TP-Link (TP-WN321G) USB wifi adapter and have the driver installed inside WinXP. When I plug-in the wifi adapter, there is an option show "Ralink 802.11g WLAN [0101]" in the virtualbox's USB icon, tick on that option, the Device Manager able to detect the hardware which shows TP-Link, but when look into the properties, it says there is no driver was install. I did try to install Ralink driver but still no luck. Just curious why my wifi adapter is TP-Link, but the option show Ralink? May I know how can I emulate the wireless network inside WindowsXP?

  Read the article

• Turn my machine in a hotspot/proxy

  - by Leonardo

  My workplace does not provide a wifi... only wired connection... but my machine has a working wifi card... is there a way to "bridge" my wired connection, making my iphone connect to it and use it as if the own machine is being used? (the idea is to make my machine provide a wifi-connection and route it through my wired connection) Details: My machine OS is win 2012 server I have full admin rights to my machine There is a corporate-proxy PS: If more details needed pls ask!

  Read the article

< Previous Page | 34 35 36 37 38 39 40 41 42 43 44 45  | Next Page >