Search Results

Search found 22600 results on 904 pages for 'remote connection'.

Page 380/904 | < Previous Page | 376 377 378 379 380 381 382 383 384 385 386 387  | Next Page >

  • Frequent and weird wifi disconnections

    - by Sidou
    How would you explain, troubleshoot (and solve) the following problem? Wifi ADSL modem router D-link 2640R installed in living room at about 1.8m height. Working fine, synchronising and getting/serving stable internet connection. First situation: -Laptop 01 in other end of the house, let's say in room01 southern to the living room, distant by about 15m. Getting stable signal of good to very good quality. No disconnection. -Laptop 02 in room02 opposite to room01 (5m West) which makes it almost at the same distance and direction from the router located 15m North. Getting stable signal of good to very good quality. No disconnection. Second situation: -Laptop 01 moved to room03 Northern to the living room (actually just 3m behind the wall where the router lies). Getting stable signal of excellent quality. No disconnection. -Laptop 02 still in room02 but now experiences frequent disconnections (actually almost impossible to get the Internet even though the signal level is still very good. Either no Internet with the wifi icon appearing connected to access point or no connection established at all which happens every 2 minutes and that means virtually no Internet at all as I can just get a timeframe of 1 minute or so to load any website or even get to the router's web based control panel. If Laptop 01 is completely shut down or its wifi adapters shut down or even still working but its wifi MAC address forbidden, then Laptop 02 has no problem at all. If Laptop 02 is moved to a nearer location to the router, in the living room for instance, then no connection problem occurs even if Laptop 01 is also connected. And also if we move back Laptop 01 to its original location (room 01), then no problem as well. I'm completely lost and don't know how to address this issue. I tried to change the Wifi channel and even tried the auto channel scan but that didn't solve it. I know that the problem is probably coming from Laptop 01 being in its new location or some sort of interference as the problem occurs only under the described condition but I have no idea how to solve it! I also scanned the neighborhood for wifi jam using InSSIDer, there are few other access points but they don't seem to affect the situation. Any ideas about the steps to follow or tools to use ?

    Read the article

  • UFW blocking random packets on 443

    - by s2jcpete
    All, I have UFW setup to allow traffic on port 443. It works as expected, though I have a large amount of UFW Block log entries. To Action From -- ------ ---- 80 ALLOW Anywhere 443 ALLOW Anywhere 22222 ALLOW Anywhere 80 ALLOW Anywhere (v6) 443 ALLOW Anywhere (v6) 22222 ALLOW Anywhere (v6) However in my syslog file I see this: [UFW BLOCK] IN=eth0 OUT= MAC=XXX SRC=<foreignip> DST=<serverip> LEN=40 TOS=0x00 PREC=0x00 TTL=116 ID=22025 DF PROTO=TCP SPT=49622 DPT=443 WINDOW=0 RES=0x00 ACK RST URGP=0 About 30 or so seconds later pound (which I'm using for SSL decryption and port redirection) throws a connection timed out messsage. I'm assuming this is because UFW is blocking the packet. I'm at a loss as to an explination. Could the packet be malformed or something, is this normal? Edit - I have since changed the /etc/defaults/ufw and set ipv6=no, so the v6 rules are no longer in the mix. The server is still showing the block / connection timed out behavior though. The new ufw status output is: Status: active Logging: on (low) Default: deny (incoming), allow (outgoing) New profiles: skip To Action From -- ------ ---- 80 ALLOW IN Anywhere 443 ALLOW IN Anywhere 22222 ALLOW IN Anywhere

    Read the article

  • Linux - Block ssh users from accessing other machines on the network

    - by Sam
    I have set up a virtual machine on my network for uni project development. I have 6 team members and I don't want them to SSH in and start sniffing my network traffic. I already have set the firewall on my W7 pcs to ignore any connection attempts from the Virtual Machine, but would like to go a step further and not allow any network access from the VM to other machines on my network. Team members will be access the VM by SSH. The only external port forwarded is to vm:22. The VM is running in VirtualBox on a bridged network connection. Running latest Debian. If someone could tell me how to do this I would be much obliged.

    Read the article

  • How to defend agains botnet http requests

    - by Killercode
    I have a server with WHM + CPanel and 5 of my costumer got infected with zbot. This means that the domains they have are constantly receiving requests to certain destinations. I tried to use mod_security but seems that it can't filter every requests... I don't really know why? I still see in the access log the connection comming in and it's consuming a LOT of bandwidth and server load Those accounts have already been clean so all of those requests go to error 404 (the ones catched on mod_security I am dropping the connection). Is there anymore ways to defend against this requests?

    Read the article

  • 4 Easy Ways to Remotely Print Over the Network or Internet

    - by Chris Hoffman
    Remote printing doesn’t have to be hard, whether you want to print to a printer down the hall or half-way around the world. We’ll cover some simple ways you can print without being directly connected to your printer. We’re going to focus on the easiest options here. We’re won’t cover setting up the Internet Printing Protocol (IPP) or JetDirect and allowing it through your firewall or complicated Windows networking configurations, as these are options best-suited for the IT Professional.    

    Read the article

  • Determining cause of random latency/loading issues

    - by Sherwin Flight
    I'm not sure exactly what details to post in regards to my issue, because I'm not sure what is relevant. Prior to the end of September my websites all loaded quickly, in almost all cases. Loading time wasn't usually more than a few seconds. However, since the end of September I noticed a big increase in page loading times. In some cases pages were taking 30 seconds or more to load. I do have a remote monitoring service monitoring some of the sites as well, and the image below shows the response times over the past month. The response times shown at the beginning of this graph were what the usual response times were prior to this issue occurring. You can see that there has been a significant increase in response times from the beginning to the end of this graph. The thing is, the problem is not happening 100% of the time. If I click through the site, or even just keep refreshing the page, about 25% of the time the pages load quickly, the remaining 75% of the time they load slowly. Sometimes the pages take so long to load that they time out, and don't load at all. I have contacted my hosting provider, and they said things at their end was fine. I don't believe the problem is my home internet provider, because all other websites load without a problem. The server is located in Texas, USA. This also raises another interesting point. My remote monitor checks my site from two locations, California, USA, and London, England. As you can see in the chart below the response time is actually shorter when checked from London, which doesn't seem to make sense, since the server is physically closer to the California monitoring location. I would have expected the London monitoring location to have higher response times since they are physically farther away. I should also point out that in some traceroute test I've done it seem like the first connection to the server seems to take the longest, then after that the rest of the page loads quickly. Below is a little chart showing the times for the first connection to the server. So, what could be causing this problem, and what steps can I take to resolve it or at least narrow down the problem? Sending the request to the server was very quick, and receiving the reply back seems pretty quick, but the WAIT time is really long. So it connects, sends the request, but then waits close to 30 seconds before it starts receiving data back. I am also aware that there are things I can do to speed up page loading times, like reducing the number of css/js files used on a page, compressing images, etc. This is not really what the source of the problem is though, because nothing has really changed on the site since before the problem started, and other sites on the same server are loading slowly as well. Any help or advice is much appreciated.

    Read the article

  • Windows 7 default VPN - Single Click to Connect

    - by Goyuix
    The default way to connect to a VPN (standard includedd MS client) seems to be to click on the network icon in the system tray to expand it, then pick the VPN connection, and click the connect button. This brings up a dialog where you can enter your username and password. I have told the VPN connection to remember my credentials. Is there some way I can skip that dialog and just have it connect? I have tried using rasdial.exe, and I can connect as long as I pass the username and password as arguments. It doesn't seem to want to use the stored credentials for some reason, maybe I need to store them with an elevated account.

    Read the article

  • Is it possible to use Linux to route between my office (which uses IPSec) and home network?

    - by Sam
    First of all, apologies if this seems vague - I'm not an admin of anything more than a home network. I have a Ubuntu box sitting on my network which does various odd tasks for me - svn serving, some file serving, Apache/MySQL/PHP which is all raring to go. I've started a new job and at the moment I'm using ShrewSoft VPN software to establish a VPN link to the office as I need it. I'd prefer to have something always running on my home network just for convenience. My home modem/router doesn't support holding a VPN connection open. What I would like to do is set up my Linux box to hold open a VPN connection to my office and keep it open permanently, and then all applicable traffic for the office be routed through this box. I'm not sure if this is possible, or how to configure the routing on the desktop PCs (Windows 7). Would appreciate any guides, etc that could help me out.

    Read the article

  • MySQL Enterprise Monitor 3.0.11 has been released

    - by Andy Bang
    We are pleased to announce that MySQL Enterprise Monitor 3.0.11 is now available for download on the My Oracle Support (MOS) web site. It will also be available via the Oracle Software Delivery Cloud in about 1 week. This is a maintenance release that includes a few new features and fixes a number of bugs. You can find more information on the contents of this release in the change log. You will find binaries for the new release on My Oracle Support. Choose the "Patches & Updates" tab, and then choose the "Product or Family (Advanced Search)" side tab in the "Patch Search" portlet. You will also find the binaries on the Oracle Software Delivery Cloud in approximately 1 week. Choose "MySQL Database" as the Product Pack and you will find the Enterprise Monitor along with other MySQL products. Based on feedback from our customers, MySQL Enterprise Monitor (MEM) 3.0 offers many significant improvements over previous releases. Highlights include: Policy-based automatic scheduling of rules and event handling (including email notifications) make administration of scale-out easier and automatic Enhancements such as automatic discovery of MySQL instances, centralized agent configuration and multi-instance monitoring further improve ease of configuration and management The new cloud and virtualization-friendly, "agent-less" design allows remote monitoring of MySQL databases without the need for any remote agents Trends, projections and forecasting - Graphs and Event handlers inform you in advance of impending file system capacity problems Zero Configuration Query Analyzer - Works "out of the box" with MySQL 5.6 Performance_Schema (supported by 5.6.14 or later) False positives from flapping or spikes are avoided using exponential moving averages and other statistical techniques Advisors can analyze data across an entire group; for example, the Replication Configuration Advisor can scan an entire topology to find common configuration errors like duplicate server UUIDs or a slave whose version is less than its master's More information on the contents of this release is available here: What's new in MySQL Enterprise Monitor 3.0? MySQL Enterprise Edition: Demos MySQL Enterprise Monitor Frequently Asked Questions MySQL Enterprise Monitor Change History More information on MySQL Enterprise and the Enterprise Monitor can be found here: http://www.mysql.com/products/enterprise/ http://www.mysql.com/products/enterprise/monitor.html http://www.mysql.com/products/enterprise/query.html http://forums.mysql.com/list.php?142 If you are not a MySQL Enterprise customer and want to try the Monitor and Query Analyzer using our 30-day free customer trial, go to http://www.mysql.com/trials, or contact Sales at http://www.mysql.com/about/contact. If you haven't looked at MEM recently, and especially MEM 3.0, please do so now and let us know what you think. Thanks and Happy Monitoring! - The MySQL Enterprise Tools Development Team

    Read the article

  • Any way to stop VMWare workstation from dropping SSH connections?

    - by oljones
    I have VMWare workstation 8 with a few Linux guests. I have had problems maintaining an active SSH connection to my VMs when they are in bridged mode. I first read that the onboard realtek network cards were not well supported so I bought a Intel Pro/1000 GT card. This supposedly had support. But this made no difference. Connections via SSH are active for about the first 3 minutes then hang and die. I have changed the TCP Checksum offload on the Intel and Realtek NICs, but this only works some of the time and even then not for very long. The best I could do was about 20 minutes before the connection was dropped. Any ideas?

    Read the article

  • When can an FTP server close its passive connections?

    - by Don Kirkby
    Does the FTP protocol allow the server to close any of its passive connections while the client is still connected? Can it tell when the client is finished receiving and then close the connection? I'm including an FTP server in my application using the pyftpdlib Python project. I've got it to work in active and passive mode, but I'm a bit concerned about when it closes its passive connections. I've tried connecting to it with both FileZilla and the default ftp command in Ubuntu, and in both cases, I get a new passive port for every request. That is, if I sit in the root folder and type ls 10 times, I use up 10 ports. This means that I have to allocate a big block of passive ports for the FTP server to use so it won't run out. As soon as the client disconnects, the server releases all the passive connections associated with that client and those ports can be reused. However, a long-running connection could use up a lot of ports.

    Read the article

  • pptp VPN, routing

    - by Adrian
    Details: eth0 = current internet port pptp1 = VPN connection, if I connect to my provider, he give me an IP address, which is accessible from the internet. This is what I need. I want to connect through this IP back to my PC. I want to keep my primary internet connection (eth0) on my PC for all traffic, but route traffic to VPN for specified application/or port, to access application/port from the IP, which I given from the pptp provider. Huhh? Difficult but, it is possible? If yes, how? Incoming port will be always: 33340 Outgoing port can be change, but usually it is 33330

    Read the article

  • Time randomly changing itself, internet randomly dying

    - by Vee
    Operating System MS Windows 8 Enterprise 64-bit CPU Intel Core i7 2700K @ 3.50GHz 45 °C Sandy Bridge 32nm Technology RAM 8,00 GB Dual-Channel DDR3 @ 800MHz (8-8-8-24) Motherboard ASRock Z77 Extreme4-M (CPUSocket) 40 °C Graphics SMXL2270HD (1920x1080@60Hz) M2094D-PZ (1680x1050@60Hz) 896MB GeForce GTX 275 (CardExpert Technology) 57 °C Hard Drives 466GB FUJITSU MAXTOR STM3500320AS (SATA) 39 °C Optical Drives ASUS DRW-2014L1T Audio High Definition Audio Device Hello everyone, I installed Windows 8 RTM a few weeks ago. It's not my first time installing it, but it's the first time having two annoying problems: 1) Randomly, the system clock changes time all by itself - to fix it I have to open the time window and sync it with the internet. 2) Randomly, internet connection stops working - to fix I have to run troubleshooting. Windows will find a problem with IP on the "Ethernet" connection and fix it. 3) In rare occasions, my PC freezes and I need to restart it (a BSOD once happened, but after that only freezes) How can I permanently solve these problems? This is what I've already tried: Reset Virus scan Stop/reset the Windows Time service Disable/re-enable Windows Time automatic internet sync Change time from BIOS Change motherboard battery

    Read the article

  • Network? or router? problem

    - by Robert H Mercer
    I have two computers networked through a Netgear WG914 router which is connected to an Ipstar satellite modem via the RG47 LAN connector. The main computer is running Windows 7 Pro 64bit and the secondary computer is running Windows 7 Home Edition 32bit. On occasion there is a loss of internet connection usually on the main computer, often followed by a loss on the secondary comuter. Not, however, always the case. Windows troubleshooter, naturally, is about as much use as a politician in government.......NONE. There appears to be no problem with the ISP bad as it is and often the connection will be remade without any help from me. The difference in the OS's is not of any relevance since I had this problem before I changed over to Windows 7. Not being a nerd when it comes to networking I wonder if anyone has any constructive suggestions.

    Read the article

  • Windows 2008 Server Unable to activate with other methods

    - by matt king
    I'm trying to activate windows 2008 server SP2 today since the activation trial is done. I do not have an internet connection with this server so I can not activate online, and with the other servers in this farm I've been able to run the slmgr -ipk xxxxx-xxxxx-xxxxx-xxxxx-xxxxx and then it would open up the activate by phone method and we would just activate that way. I say again, I don't have an internet connection so I can not do the online activate. If I do the slui 4 it brings up the activation window but show me other ways to activate is still greyed out. I've disabled the NIC on this Hyper-V server and I still can not get the other way to activate to show up... Anyone have any ideas? This computer is one of my AD servers so.. it being in notification mode kind of sucks. Thanks.

    Read the article

  • scp -q isn't quiet between different hosts

    - by pythonic metaphor
    So scp -q file host:file and scp -q host:file file are both quiet, i.e. don't give the progress meter. But when I run scp -q host1:file host2:file, I still get the progress meter as well as a Connection to host1 closed. message. The progress meter can be gotten rid of by redirected stdout to /dev/null (although I'd rather not have to), but the connection closed messages comes on stderr, which I definitely want to keep in case there's a real error. How can I make scp quiet? Do I have to run ssh host1 "scp -q file host2:file"?

    Read the article

  • Ethernet port sleeping on PS3 running linux

    - by Doug
    My lab has a PS3 running Ubuntu Linux 9.04 Server Edition. After a period of a few hours with no use, the Ethernet connection (eth0) seems to go to sleep, causing the connection to be lost. Pinging or trying to SSH into the machine results in no response. The fix I've been using is to access the machine locally and restart it (trying to bring eth0 down then up doesn't seem to correct it). I've tried setting up an hourly cron job that runs on the PS3 and pings another machine just to create network activity, but this doesn't seem to solve the problem either. Update: The solution was to run the above cron job much more frequently: every 10 minutes works.

    Read the article

  • Still prompted for a password after adding SSH public key to a server

    - by Nathan Arthur
    I'm attempting to setup a git repository on my Dreamhost web server by following the "Setup: For the Impatient" instructions here. I'm having difficulty setting up public key access to the server. After successfully creating my public key, I ran the following command: cat ~/.ssh/[MY KEY].pub | ssh [USER]@[MACHINE] "mkdir ~/.ssh; cat >> ~/.ssh/authorized_keys" ...replacing the appropriate placeholders with the correct values. Everything seemed to go through fine. The server asked for my password, and, as far as I can tell, executed the command. There is indeed a ~/.ssh/authorized_keys file on the server. The problem: When I try to SSH into the server, it still asks for my password. My understanding is that it shouldn't be asking for my password anymore. What am I missing? EDIT: SSH -v Log: Macbook:~ michaeleckert$ ssh -v [USER]@[SERVER URL] OpenSSH_6.2p2, OSSLShim 0.9.8r 8 Dec 2011 debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: /etc/ssh_config line 53: Applying options for * debug1: Connecting to [SERVER URL] [[SERVER IP]] port 22. debug1: Connection established. debug1: identity file /Users/michaeleckert/.ssh/id_rsa type -1 debug1: identity file /Users/michaeleckert/.ssh/id_rsa-cert type -1 debug1: identity file /Users/michaeleckert/.ssh/id_dsa type -1 debug1: identity file /Users/michaeleckert/.ssh/id_dsa-cert type -1 debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_6.2 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.5p1 Debian-6+squeeze3 debug1: match: OpenSSH_5.5p1 Debian-6+squeeze3 pat OpenSSH_5* debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA [STRING OF NUMBERS AND LETTERS SEPARATED BY SEMI-COLONS] debug1: Host ‘[SERVER URL]' is known and matches the RSA host key. debug1: Found key in /Users/michaeleckert/.ssh/known_hosts:2 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password debug1: Next authentication method: publickey debug1: Trying private key: /Users/michaeleckert/.ssh/id_rsa debug1: Trying private key: /Users/michaeleckert/.ssh/id_dsa debug1: Next authentication method: password [USER]@[SERVER URL]'s password: debug1: Authentication succeeded (password). Authenticated to [SERVER URL] ([[SERVER IP]]:22). debug1: channel 0: new [client-session] debug1: Requesting [email protected] debug1: Entering interactive session. debug1: Sending environment. debug1: Sending env LANG = en_US.UTF-8 Welcome to [SERVER URL] Any malicious and/or unauthorized activity is strictly forbidden. All activity may be logged by DreamHost Web Hosting. Last login: Sun Nov 3 12:04:21 2013 from [MY IP] [[SERVER NAME]]$

    Read the article

  • DVI-D Splitter Not Working with GeForce 8400gs

    - by jimdrang
    I have a GeForce 8400gs and it has a DVI and VGA port on the back. I was using dual monitors with one VGA and one DVI cable. I wanted both displays to be digital so I bought a DVI-D splitter and put one DVI cable in each monitor, connected them to the splitter and put the single merged connection in the back of the cards DVI connection. It will not recognize the second monitor (I'm not even sure how it determined which one was the first monitor). The tech specs state that it supports "Two dual-link DVI outputs for digital flat panel display resolutions up to 2560x1600" http://www.nvidia.com/object/geforce_8400_tech_specs.html. Do I need a different converter or is my only option for dual monitors with this card one VGA, one DVI?

    Read the article

  • Enable/disable wireless interface in a bat file

    - by Herms
    Is there a way to enable/disable a wireless network interface via the command line (so I can put it in a bat file)? When I'm in the office I use a wired connection, but Windows still occasionally bugs me about my wireless connection not being connected (even though I turned off the option for notifying me when there's no connectivity). I'm guessing the only way to stop it from bugging me is to disable the interface, but I'd rather not have to go into the network settings every time I need to do so. I'd like to set up a bat file or a shortcut that I can use to enable/disable the wireless (preferably a single one that toggles the current state), and then just set up a keyboard shortcut for that. I just have no idea how to do so from the command line.

    Read the article

  • How-To: Run CMSDK against a RAC cluster

    - by frank.closheim
    Using CMSDK in a production environment often requires a robust, reliable and failover enabled repository. When using Oracle Real Application Cluster (RAC) with your CMSDK repository you need to have a specific configuration in place to support such a setup. This post will explain the configuration steps required when running CMSDK 9.0.4.6 with Oracle WebLogic Server (WLS).In the previous CMSDK 9.0.4.2 version a RAC enabled connect string looked like this: (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = rac1)(PORT = 1521))(ADDRESS = (PROTOCOL = TCP)(HOST = rac2)(PORT = 1521))(LOAD_BALANCE = NO)(FAILOVER = ON)(CONNECT_DATA =(SERVICE_NAME = rac)(failover_mode = (type=select)(method=basic)))CMSDK 9.0.4.6 makes use of data sources to connect to the underlying database. These data sources are configured inside your Application Server, such as Oracle WebLogic Server.In Oracle WebLogic Server 10.3.4, a single data source implementation has been introduced to support an RAC cluster. It responds to Fast Application Notification (FAN) events to provide Fast Connection Failover (FCF), Runtime Connection Load-Balancing (RCLB), and RAC instance graceful shutdown. XA affinity is supported at the global transaction Id level. The new feature is called WebLogic Active GridLink for RAC; which is implemented as the GridLink data source within WebLogic Server.This GridLink data source also works with Oracle Single Client Access Name (SCAN). SCAN is a feature used in RAC environments that provides a single name for clients to access any Oracle Database running in a cluster. You can think of SCAN as a cluster alias for databases in the cluster. The benefit is that the client’s connect information does not need to change if you add or remove nodes or databases in the cluster.The CMSDK 9.0.4.6 documentation describes how to create a regular JDBC data source named jdbc/OracleDS. Please refer to the following document which describes in detail how to create a GridLink data source in WLS.

    Read the article

  • How do I remove only shopping searches?

    - by Amanda
    I have a brand new 13.10 install and I want all this shopping spyware nonsense gone. Searching for "Ubuntu shopping spyware nonsense" led me to apt-get remove unity-lens-shopping but I don't actually see a unity-lens-shopping package. How do I remove shopping searches in 13.10? Update: Is there any way to distinguish the scopes that search remote servers (Ebay, Amazon, AskUbuntu) from the ones that search my local computer? Or do I have to go through them all?

    Read the article

  • Packing up files on my machine, sending it to a server, and unpacking it

    - by MxyL
    I am implementing a feature in my application that sends all files in a specified folder to a server. I have the basic FTP transaction set up using Apache Commons FTPClient: it sets up a connection and transfers a file from one place to another. So I can simply loop over the directory and use this connection to transfer all the files. However, this could be better. Rather than transferring each file one by one, it makes more sense to pack it up in a compressed archive and then send the whole file at once. Saves time and bandwidth, since these are just text files so they compress nicely. So I would like to add automatic archive packing and unpacking. This is the workflow I have planned out, using zip compression: Zip all files in the folder Send the file over Unzip the files at its destination 1 and 2 are easy since the files are on the local machine, but I'm not sure how to accomplish the last step, when the files are now on a remote server. What are my options? I have control over what I can put and run on the server. Perhaps it is not necessary to do the packing/unpacking myself?

    Read the article

  • How to host an AP or a hotspot?

    - by user1048138
    I'm running Ubuntu 12.04 as a virtual machine on my Mac. Since I am unable to get the virtual machine to have full access to my WiFi card, I bought another USB WiFi card to use. This is my WiFi card. If you are unfamiliar with Virtual machine, as far as I know, since the Ubuntu has its own card now, it shouldn't matter. I have followed these guides with no luck: https://help.ubuntu.com/community/WifiDocs/WirelessAccessPoint http://www.danbishop.org/2011/12/11/using-hostapd-to-add-wireless-access-point-capabilities-to-an-ubuntu-server/ The problem is that the WiFi connection appears on all of the machines that I have in my house: 2 iPhones, Dell machine running Ubuntu and two Macbooks. However the connection times out on all of these machines. Questions: Could this be a driver issue if that same WiFi card can connect to other WiFi points and use its internet Could this be DHCP related? I would think not. It should at least get a 169.X.X.X address? No? Any solutions for me?

    Read the article

  • Scripted SOA Diagnostic Dumps for PS6 (11.1.1.7)

    - by ShawnBailey
    When you upgrade to SOA Suite PS6 (11.1.1.7) you acquire a new set of Diagnostic Dumps in addition to what was available in PS5. With more than a dozen to choose from and not wanting to run them one at a time, this blog post provides a sample script to collect them all quickly and hopefully easily. There are several ways that this collection could be scripted and this is just one example. What is Included: wlst.properties: Ant Properties build.xml soa_diagnostic_script.py: Python Script What is Collected: 5 contextual thread dumps at 5 second intervals Diagnostic log entries from the server WLS Image which includes the domain configuration and WLS runtime data Most of the SOA Diagnostic Dumps including those for BPEL runtime, Adapters and composite information from MDS Instructions: Download the package and extract it to a location of your choosing Update the properties file 'wlst.properties' to match your environment Run 'ant' (must be on the path) Collect the zip package containing the files (by default it will be in the script.output location) Properties Reference: oracle_common.common.bin: Location of oracle_common/common/bin script.home: Location where you extracted the script and supporting files script.output: Location where you want the collections written username: User name for server connection pwd: Password to connect to the server url: T3 URL for server connection, '<host>:<port>' dump_interval: Interval in seconds between thread dumps log_interval: Duration in minutes that you want to go back for diagnostic log information Script Package

    Read the article

< Previous Page | 376 377 378 379 380 381 382 383 384 385 386 387  | Next Page >