Search Results

Search found 11629 results on 466 pages for 'cloud solutions'.

Page 381/466 | < Previous Page | 377 378 379 380 381 382 383 384 385 386 387 388  | Next Page >

• Weird PCI bug: lots of missed packets, or data comes in "bursts"

  - by Thomas O

  I have an ABIT KN9 motherboard. It has one PCI-e x16 slot, three PCI-e x4 slots and two legacy PCI. My problem is with the legacy PCI (which I shall just call "PCI".) I currently have an Nvidia GeForce 8600 GT (a low end card) installed in the x16 slot and a TV card in PCI #1; the x4 slots are unused, as is PCI #2. I plan to upgrade the graphics card soon, the current card was spare. I sometimes install a USB expander in PCI #2 but it causes a lot of problems - see below. The problem is under Linux (Ubuntu 10.10, Linux 2.6.35-22-generic), but probably under all operating systems (I have not yet been able to test Windows, but I suspect it will do the same as the problems occur on the BIOS/POST side too, e.g. when using a USB keyboard on the expander the keyboard will not work at all) PCI has an enourmous delay, and packets arrive in large chunks. For example, when using the USB expander, my USB mouse lags and jumps in large steps every second or so, while using the motherboard USB does not present this problem. My TV card will only do one or two frames per second, and the program (xawtv) usually times out and crashes. In dmesg, I'm getting messages like: bttv0: timeout: drop=74, irq=154/100476, risc=31f6256c, bits: VSYNC HSYNC OFLOW RISCI for my TV card, and similar timeout issues for my USB expander with a mouse. I received the motherboard, processor and RAM second hand and have only just got around to building it, so I don't know if this problem has always existed, or if it's a result of my set up. If anyone has any hints or solutions it would be appreciated - this is kind of a show-stopper for me.

  Read the article

• IP-dependent local port-forwarding on Linux

  - by chronos

  I have configured my server's sshd to listen on a non-standard port 42. However, at work I am behind a firewall/proxy, which only allow outgoing connections to ports 21, 22, 80 and 443. Consequently, I cannot ssh to my server from work, which is bad. I do not want to return sshd to port 22. The idea is this: on my server, locally forward port 22 to port 42 if source IP is matching the external IP of my work's network. For clarity, let us assume that my server's IP is 169.1.1.1 (on eth1), and my work external IP is 169.250.250.250. For all IPs different from 169.250.250.250, my server should respond with an expected 'connection refused', as it does for a non-listening port. I'm very new to iptables. I have briefly looked through the long iptables manual and these related / relevant questions: http://serverfault.com/questions/57872/iptables-question-forwarding-port-x-to-an-ssh-port-of-different-machine-on-the-n http://serverfault.com/questions/140622/how-can-i-port-forward-with-iptables However, those questions deal with more complicated several-host scenarios, and it is not clear to me which tables and chains I should use for local port-forwarding, and if I should have 2 rules (for "question" and "answer" packets), or only 1 rule for "question" packets. So far I have only enabled forwarding via sysctl. I will start testing solutions tomorrow, and will appreciate pointers or maybe case-specific examples for implementing my simple scenario. Is the draft solution below correct? iptables -A INPUT [-m state] [-i eth1] --source 169.250.250.250 -p tcp --destination 169.1.1.1:42 --dport 22 --state NEW,ESTABLISHED,RELATED -j ACCEPT Should I use the mangle table instead of filter? And/or FORWARD chain instead of INPUT?

  Read the article

• MySQL unstable behavior with external stroge

  - by onurozcelik

  In our project we are using MySQL 5.0.90(InnoDB engine) server with an external storage. We store MySQL data files in an external storage. When the external storage down for a reason we have unstable behaviours. So we made some tests. In Windows Server 2008 We closed external storage physically. MySQL service stoped and we could not reach the server. Then we opened the storage unit and we could not start service until we reconfigured MySQL. We made storage unit offline from operating system. After 3-4 minutes and some insert trials(some insert trials succeded) MySQL service stoped and we could not reach the server. Then we made storage unit online and we could start the service(not automatically). In Windows Server 2003 We made storage unit offline. After 3-4 minutes and some insert trials(some insert trials succeded) MySQL service stoped and we could not reach the server. Then we made storage unit online we could not start the service until we reinstalled MySQL. Before reinstall we tried to reconfigure but it did not work. We closed external storage physically. MySQL service stoped and we could not reach the server. After that we opened the storage unit and we could start service(not automatically) We expect service to autostart after storage unit is online/open. But these tests show unstable behaviors. Is there any solutions to this.

  Read the article

• Proper way to use hiera with puppetlabs-spec-helper?

  - by Lee Lowder

  I am trying to write some rspec tests for my modules. Most of them now use hiera. I have a .fixures.yml: fixtures: repositories: stdlib: https://github.com/puppetlabs/puppetlabs-stdlib.git hiera-puppet: https://github.com/puppetlabs/hiera-puppet.git symlinks: mongodb: "#{source_dir}" and a spec/classes/mongodb_spec.rb: require 'spec_helper' describe 'mongodb', :type => 'class' do context "On an Ubuntu install, admin and single user" do let :facts do { :osfamily => 'Debian', :operatingsystem => 'Ubuntu', :operatingsystemrelease => '12.04' } end it { should contain_user('XXXX').with( { 'uid' => '***' } ) should contain_group('XXXX').with( { 'gid' => '***' } ) should contain_package('mongodb').with( { 'name' => 'mongodb' } ) should contain_service('mongodb').with( { 'name' => 'mongodb' } ) } end end but when I run the spec test, I get: # rake spec /usr/bin/ruby1.8 -S rspec spec/classes/mongodb_spec.rb --color F Failures: 1) mongodb On an Ubuntu install, admin and single user Failure/Error: should contain_user('XXXX').with( { 'uid' => '***' } ) LoadError: no such file to load -- hiera_puppet # ./spec/fixtures/modules/hiera-puppet/lib/puppet/parser/functions/hiera.rb:3:in `function_hiera' # ./spec/classes/mongodb_spec.rb:15 Finished in 0.05415 seconds 1 example, 1 failure Failed examples: rspec ./spec/classes/mongodb_spec.rb:14 # mongodb On an Ubuntu install, admin and single user rake aborted! /usr/bin/ruby1.8 -S rspec spec/classes/mongodb_spec.rb --color failed Tasks: TOP => spec_standalone (See full trace by running task with --trace) Module spec testing is relatively new, as is hiera. So far I have been unable to find any suitable solutions. (the back and forth on puppet-dev was interesting, but not helpful). What changes do I need to make to get this to work? Installing puppet from a gem and hacking on rubylib isn't a viable solution due to corporate policy. I am using Ubuntu 12.04 LTS + Puppet 2.7.17 + hiera 0.3.0.

  Read the article

• Create "raw disk file" from WIM file

  - by Joe Baltimore

  First timer here. I've searched around here, but haven't found a question like the one I have. Apologies if I missed it. The challenge at hand: produce a "raw disk image file" from a given WIM file. What I am pursuing so far is to use imagex.exe with the "/apply" operation to take the WIM and lay it down in a directory on a server. That seems to produce all the necessary "stuff" I need in that directory. How would I take that content and produce a "raw disk image file"? I'm told the definition of "raw disk image file" is a block-by-block copy of the disk image, which I hope is the output of the "imagex.exe /apply" command I use currently, but stored in a single file I can hand back to another system in our solution. imagex.exe /apply image.wim 1 R:\WimImagePoint I would like to take the contents of R:\WimImagePoint and produce the elusive (to me) "raw disk image file". ISO is not what they want, nor is anything requiring winPE. Any pointers? External utilities' references are welcome. Would like to avoid unmanaged code solutions as much as possible, but will entertain them if that's the only route. Also, I am not married to the idea of imagex /apply as the starting point, it's just the comfort zone so far.

  Read the article

• Windows and file system abstraction - how much does it matter where something comes from?

  - by deceze

  I have come across the following phenomenon and would like to know how leaky Windows' file system abstraction is or if there's something else involved. I partitioned the hard disk of my MacBook Pro and installed Windows 7 (64 bit). The Bootcamp driver package includes file system drivers (right term?) that enable Windows to access the Mac OS HFS+ partition. AFAIK it's a read-only access, but it works. Now, I have some disk images of stuff I usually install, so I grabbed a copy of Daemon Tools to mount them. When I mount an image saved on the HFS+ partition, about two out of three installers on these disks (usually InstallShield) crash with all sorts of weird errors. Most are just gibberish that lead to all sorts of non-solutions on Google, one was "This application is not the right type for your computer, check if you need 32 or 64 bit versions." When moving the image files to another Windows 7 computer on the network and mounting them from the network share, they work fine. My question now is, why do applications behave differently depending on whether the read-only image file, which should be abstracted away through the read-only virtual Daemon Tools drive, is located on a read-only HFS+ partition or on a Windows network share? And I'll just roll this into the question as well since I was wondering: Does the file system of a network share matter? Does the client system need to understand the file system of the share host or is that abstracted away in SMB?

  Read the article

• CDN Rerouting on 404 (file not yet in synch with original storage)

  - by Alan Ristic

  Here is the problem. I've setup my app(on EC2) to store uploaded images directly on Amazon S3. I'd like to be able to serve static files(cdn) from my 'home' server so I wrote script that does sync from S3. But there is a window of (at least) one minute in synch. Now I see two solutions on the problem of pics not been available on 'home' server here: 1.I write script on EC2 (where the app resides) to fetch from DB pics that have status of "not-yet-synch", which is default state when user uploads picture. The script then does a ping to picture and if it gets OK response, updates DB from "not-yet-synch" to "synch". 2.Prefered solution would be to let apache (in this case) redirect request for an image if it sees 404 (e.g. doesent find image requested) to S3. This way I wouldn't need script from solution 1. So what approach do you suggest I take in solving this redundancy problem? Or what is practice in production environments? To further clarify; I'd like so serve images first from 'home' server, if that fails serve them from S3. Tnx, Alan

  Read the article

• How to best convert a fully encrypted drive into a Virtual Machine?

  - by SiegeX

  I have a Windows XP laptop that uses GuardianEdge's Encryption Plus to fully encrypt the drive from bootup. What I would like to do is install a much larger (unencrypted) hard drive with Windows 7 on it and turn this fully encrypted drive into a Virtual Machine that can be ran in either Virtualbox or VMWare on the Windows 7 host. I've read many howto's that talk about using an imaging tool like Acronis True Image to image the drive then passing that through VMWare's VCenter Converter to turn it into a format that VMWare can understand. Unfortunately this seems to all far apart when you are dealing with a fully encrypted drive because Acronis cannot recognize the file system and attempts to do a sector-by-sector copy of the entire hard drive. This is extremely wasteful since the drive is 120GB but the file system is only using 10GB of that. Even if I were OK with going with an inefficient 120GB sector-by-sector copy, I'm not sure that this would even work under VMWare or Virtualbox. Unfortunately, the Guardian Edge boot-time login comes up only after the hard drive has been selected as the boot device; preventing me from being able to decrypt the drive prior to booting an Acronis True Image CD so that it can recognize the underlying file system. I'm sure I'm not the first person to want to do this but I am having a heck of a time finding solutions to this problem. All suggested/answers welcomed. Thanks

  Read the article

• Looking for a host based network monitor solution

  - by Ole Martin Handeland

  Hi all! Problem So, my hosting company has a network usage graph for my dedicated server. It seems that one day earlier this month, my network usage suddenly spiked with several hundred megabytes transferred (usually it's in the tens, not hundreds). It was probably me, but i just can't be sure who or what it was. Question So my question is; does anyone know of any host based solution for monitoring network usage that would tell me the client's IP-address, the port/service he/she used? What I don't want I'm just guessing that someone will suggest i use nagios, munin, zabbix, cacti, mrtg - I've also looked at those, but a graph over network usage will not give me the answers I'm looking for. :-) Almost there I've already looked at a lot of monitoring solutions, and I've tried [ntop][http://www.ntop.org/], [darkstat][http://unix4lyfe.org/darkstat/] and others. Darkstat just didn't give me the answers. Although it listed a lot of statistics, and i could list the clients - it doesn't show me the network usage for a particular period. Ntop is by far the best I've seen so far - but i think it mostly shows current network usage, not the historical part. I could run apt-get upgrade and download a whole bunch of software, but not see it in the log afterwards.

  Read the article

• Is there a way to run CUDA applications with the CUDA device being a secondary adapter?

  - by Slartibartfast

  I've been trying to run a CUDA program on a remote computer which has Windows 7 installed. The GPU is GeForce GTX 480. One of the problems I've been facing is that, the computer has two adapters, 1) Standard VGA Adapter 2) NVIDIA GeForce GTX 480 Even though this shows in the device manager. The desktop uses the standard VGA Adapter. I'm assuming this is because the Standard VGA is the primary adapter. Also the device manager shows that the monitor is connected to the standard VGA Adapter. In this scenario if i try to run any CUDA application it fails to recognise a CUDA capable device. Is it necessary for the NVIDIA adapter to be the primary one? Or is there any way to use CUDA when the graphics card is a secondary adapter. I've seen a few posts in the NVIDIA forums on this before, one suggests using another low cost NVIDIA card as the primary adapter, but that is currently not an option. I couldn't find any other solutions. Thanks I tried running the deviceQuery test from the NVIDIA GPU Computing Samples. This was the result i obtained CUDA Device Query (Runtime API) version (CUDART static linking) cudaGetDeviceCount FAILED CUDA Driver and Runtime version may be mismatched FAILED The driver version I'm using is 263.06. The CUDA version is 3.2 I ran the same test on my desktop which also has windows 7 and a GeForce GTX 465. The CUDA toolkit version is 3.2. The driver version was the same and the test passed, although it failed with an older driver.

  Read the article

• Windows 7 fails to connect to the internet a few minutes after startup

  - by SageTheGreat

  Problem Earlier today, when I turned on my desktop computer, my internet connection works fine. Cryptocurrency miners connecting and hashing as usual and I can browse websites. But after a few minutes, my miner fails indicating that there is something wrong with my internet connection. Tried refreshing my browser and is stuck at "resolving host", and then presented me an error. After that, i can't browse sites anymore. But the weird thing is that the network icon in Windows 7 shows no signs of problems. Solutions Made Restarted my computer without doing anything: Problem persists. Tried using the network troubleshooter of windows: Reported no problems Stopped bonjour still no progress. Loaded windows using Last good config: still no progress. Restarted Modem: No change. Current Status I currently did a system restore to my system to a point before installing the latest update from Microsoft. Because earlier today, I installed some updates and after that, the problem started to appear. (After system restore, same problem.) Latest Programs installed before the problem MS Visual Studio 2013 (but internet still worked fine after the install). I hope someone could provide answers on this problem. It is my first time encountering this. EDIT: Additional Info OS: Windows 7 SP1 64-bit AV: Avast Free Antivirus Internet Connection Type: Ethernet It appears that my Laptop can't even connect to the machine thru Remote Desktop My laptop and phone on WiFi works fine and can connect to the internet. EDIT 2: Whenever I boot into Safe Mode, my Internet is fine.

  Read the article

• All commands stopped working in centos 6.5

  - by Michael

  I have made a big mistake while removing some duplicate packages as it appears to be broken. yum 1036 rpm -e --nodeps glibc-2.12-1.132.el6_5.2.x86_64 1037 rpm -e --nodeps nscd-2.12-1.132.el6_5.2.x86_64 1038 rpm -e --nodeps glibc-common-2.12-1.132.el6_5.2.x86_64 1040 rpm -e --nodeps glibc-common-2.12-1.132.el6.x86_64 glibc-devel-2.12-1.132.el6.x86_64 glibc-headers-2.12-1.132.el6.x86_64 1041 rpm -e glibc.x86_64 1042 rpm -e --nodeps glibc.x86_64 The issue happened after doing 1042 step. None of commands work(including yum, rpm, ls, cp etc) and getting error /lib64/ld-linux-x86-64.so.2: bad ELF interpreter: No such file or directory I thought that installing glibc after removing all the current ones would help to resolve the duplicate package error :( Now I realised that it is used as the C library in the GNU system and most systems with the Linux kernel. It defines the "system calls" and other basic facilities such as open, malloc, printf, exit, etc. Is there any possible solutions other than reinstall? I have lost ssh access. Maybe anything can be done using rescue cd? Thanks

  Read the article

• Can't write to samba share

  - by Tiddo

  I try to setup a samba file server, but whatever I do I can't get write access to work (reading works fine). This is my current situation: I have a local fileserver with 3 harddisks mounted at /mnt/share/disk<nr>. 2 of these use the ext4 filesystem, the third one is ntfs. This file server runs Fedora 18 32-bit. The root folders of these harddisks are owned by superman:superman, and testparm outputs the following: [global] workgroup = WORKGROUP netbios name = FILE_SERVER server string = Samba Server Version %v interfaces = lo, eth0, 192.168.123.191/8 log file = /var/log/samba/log.%m max log size = 50 unix extensions = No load printers = No idmap config * : backend = tdb hosts allow = 192.168.123. cups options = raw wide links = Yes [share] comment = Home Directories path = /home/share/ write list = superman, @users force user = superman read only = No create mask = 0777 directory mask = 0777 inherit permissions = Yes guest ok = Yes I've tried a lot to get this to work: the disk are chmodded to 777, I've tried turning off selinux, I've added the samba_share_t label to the disks and as can be seen in the above output I tried to make the smb config as permissive as I could, but still I cannot write to the share (tried from Windows 7 and another Fedora installation). What can I try to be able to write to the shares? EDIT: The replies I got so far are mostly concerned with the smb.conf. I have however tried a lot of different setup, ready made configs, and solutions to similar problems for the smb.conf file, so I suspect that the real problem is somewhere else.

  Read the article

• What is the 'best practice' for installing perl modules on Solaris/OpenSolaris?

  - by AndrewR

  I'm currently in the process of writing setup instructions for some software I've written that is implemented as a set of Perl modules. Having done this for various flavours of Linux, I'm now doing the same for Solaris/OpenSolaris (v10 only). Part of the setup process is to make sure that dependent Perl modules are installed. This has been pretty easy on Linux as the Perl modules I require tend to be within the distro's packaging system (eg yum install perl-Cache-Cache). This is not the case on Solaris so I'm working on setup instructions that use the CPAN module to fetch dependent modules (eg perl -MCPAN -e 'install Cache::Cache'). This works ok but there are known problems with modules that require things to be built with a C compiler. The problem is that the C Makefile generated assumes you're using Sun's compiler and uses command-line options not understood by gcc, which you may be using instead. Consulting teh Internetz has thrown up a number of solutions to this: Install and use Sun's compiler Use the perlgcc wrapper script Edit the makefiles by hand (yuk) All of these work. My question to those more familiar with Solaris than me is: Is one of these the 'best' or 'most commonly used' method?

  Read the article

• ssd firmware, linux: updating large batch of drives

  - by wryfi

  I was recently hit with a fatal firmware bug that affected dozens of Crucial SSDs deployed in my datacenter. Many of the affected machines use LSI or other proprietary SAS controllers, which Crucial's bootable ISO does not recognize. None of the affected machines has a Windows license. The story is roughly similar for other SSD mfrs, including Samsung and Intel. To resolve this issue, I was forced to stop each machine, remove the affected SSD, remove the SSD from its hotswap caddy, install it temporarily into my ThinkPad, flash the firmware, reverse, rinse, repeat. It took the better part of a day to get through all the affected devices. I am looking for hardware, software, and/or purchasing strategies to ease this pain, as SSD firmware bugs seem inevitable, and our SSD footprint is growing. My first thought is to get a laptop with eSATA and one of these cables (http://www.newegg.com/Product/Product.aspx?Item=N82E16812311004). That should at least make it so I don't have to remove the drives from their caddies. Surely others have run into this. Any novel solutions?

  Read the article

• Can somebody please recommend a good local file backup utility that will be Windows & OSX Compatible?

  - by JAG2007

  I have an external hard drive that I keep all of my work files on and transfer them back and forth between my Windows 7 box at work, and my Mac at home (I work from home frequently). Can someone recommend a really good backup utility that I can use on that external drive, to back the files up to my work computer locally, or the other external drive on my machine at work? I'm looking for preferably a free or open source software, and I'd prefer it to be cross system compatible, although I would also consider using a software that will only work on the Windows box. Also, I will consider a software that has a price assuming it is a really good piece of software and the price is reasonable (like under $50 or so). I checked out CrashPlan a bit, but not sure if that's gonna be really what I'm looking for. To reiterate I'm not looking for online backup solutions, just a piece of software that can back up my data to another drive locally. CrashPlan Free seems to offer this, but not sure how good it is (considering their goal is to get me to buy a pay for version). *NOTE: I'm running Windows 7 in 64bit so I need a piece of software that will be compatible with 64bit OS. My previous software, PC Backup, is not. That's partly why I'm in this boat.

  Read the article

• Windows Server - share files without access for administrator

  - by Pawel

  We have a MS Windows Server 2008 R8 based server that is administrated by our IT department. We would like to achieve two things simultaneously: A folder on the server, containing several thousand files (new files added frequently) that is accessible to some ActiveDirectory users (e.g. board of directors) but is not accessible by IT department employees IT department employees still maintain rights to administrate the server, including installing new software and services We already checked some solutions: Using NTFS access rights. Unfortunately IT (members of "Administrators" group) can set themselves as new owners of the files and change the permissions so that they gain access to the files. Enabling EFS. Unfortunately even if you do not allow IT to access files, they still can disable EFS completely because they have administrative rights. Moreover as far as I know you have to manually add permissions for all users but the owner for each new file - very inconvenient. Creating a new role for the IT department that has all the privileges apart from taking ownership of files. Unfortunately if you're not a member of the Administrators group, you cannot install new software, no matter what privileges you add to the role. TrueCrypt - nice free encryption software, but with poor sharing capabilities. You can either mount an encryption container on the server (and then IT has access to its contents) or you mount them locally but only one user can mount it for writing. AxCrypt - free encryption software that enables file-by-file encryption on the server. There are some disadvantages though - you have to manually encrypt each new file added. The files have their extensions changes. You can only set one password for all files (so all users have to know this one password). Any other ideas? Our budget is limited so enterprise-class software from Symantec or PGP would probably be not an option.

  Read the article

• lsof not showing what port a proc is listening on

  - by ericslaw

  I have many processes on a box listening on several ports. I am trying to map ports to pids. The problem is that lsof is not telling me what ports belong to which process. Given an apache listening on port 80, I can see it listening via netstat: user@host% netstat -an|grep LISTEN|grep 80 *.80 *.* 0 0 49152 0 LISTEN But when I try to map port 80 to a pid I get nothing: user@host% lsof -iTCP:80 -t When I try seeing what sockets that specific pid is using I get: user@host% lsof -lnP -p31 -a -i COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME libhttpd. 31 0 15u IPv4 0x6002d970b80 0t0 TCP *:65535 (LISTEN) Notice the *:65535 in the NAME column. Does anyone know why lsof is not reporting the port in use? I am running as root. I am using a mix of lsof and os versions: lsof v4.77 on Solaris10 sparc lsof v4.72 on Redhat4.2 etc I know that linux solutions can use "netstat -p", so I guess I'm only looking for why solaris isn't working, but I find lsof is frequently silent and not showing me expected data.

  Read the article

• TFTP Timing Out on Ubuntu VM

  - by valsidalv

  I'm running a Windows 7 PC with VMware installed which has my Ubuntu (10.04 Lucid Lynx). I recently installed a DHCP server and TFTP (Xinet tftpd) using these instructions. I've mapped a network drive so that my Windows has access to all the files in my VM through a 192.x.x.x IP address. I'm trying to throw some custom firmware onto a router. The router has its own built-in TFTP utility that will download the image. It successfully manages to do everything but it is slow because it writes it to flash memory. There is another method that is much quicker because it writes to RAM directly but it must use the TFTP server in Ubuntu. The issue I'm facing is that the Ubuntu TFTP transfer seems to be timing out. The transfer starts but never goes past ~60%. Here's my /etc/xinetd.d/tftp file (similar to a known working config): service tftp { protocol = udp port = 69 socket_type = dgram wait = yes user = nobody server = /usr/sbin/in.tftpd server_args = -s /home/user/tftp/ disable = no cps = 300 2 per_source = 60 } I've done some searching but can't find any parameters for this file to control timeout time or number of retries. The last two arguments (cps, per_source) and completely alien to me (can anyone explain). I have a few possible solutions but the easiest would be to get this TFTP server working. Can anyone help? Either with a timeout configuration or maybe even recommend a different TFTP server? Thanks!

  Read the article

• Looking for Remote Control that works with everything (even Windows 7 Media Center)

  - by T Reddy

  Using my Google-Fu, it seems that the most basic of things one gets with any DVR is the remote control. Had I known it would be difficult just to get a consumer IR receiver for Windows 7 I may not have bothered to build an HTPC. But too late, I already have the HTPC ready to go (minus the CETON card...) So I'm moving away from TiVo, I hate paying the monthly fees and my box is ancient. I'm looking for these solutions to my HTCP setup...I want to: Switch audio from HDMI to SPDIF via the remote control (i.e., switch from TV to Receiver) (as a side note, the built-in audio on the mobo has software to do this). Pressing the volume button on the remote will always change the TV's volume (or the Receiver's if possible) and NOT the PC's volume. The remote/receiver works well around 25 feet. Bonus if the IR Receiver can work with my existing TiVo remote (or other remotes laying around the house) I read a review of the Bluetooth TiVo remote...it sounds promising...but I'm not sure if it is great for Windows 7 HTPC?

  Read the article

• How can I proxy multiple LDAP servers, and still have grouping of users on the proxy?

  - by Chris

  I have 2 problems that I'm hoping to find a common solution to. First, I need to find a way to have multiple LDAP servers (Windows AD's across multiple domains) feed into a single source for authentication. This is also needed to get applications that can't natively talk to more than one LDAP server to work. I've read this can be done with Open LDAP. Are there other solutions? Second, I need to be able to add those users to groups without being able to make any changes to the LDAP servers I'm proxying. Lastly, this all needs to work on Windows Server 2003/2008. I work for a very large organization, and to create multiple groups and have large numbers of users added to, moved between, and removed from them is no small task. This normally requires tons of paperwork and a lot of time. Time is the one thing we don't normally have; dodging the paperwork is just a plus. I have very limited experience in all this, so I'm not even sure what I'm asking will make sense. Atlassian Crowd comes close to what we need, but falls short of having it's own LDAP front end. Can anyone provide any advice or product names? Thanks for any help you can provide.

  Read the article

• Windows XP / Outlook 2003 error messages

  - by AboutDev

  Can anyone help with this issue? I am trying to help someone and could use some expertise. Error Message #1: Microsoft Office Small Business Edition 2003 With CD icon "The feature you are trying to use is on a CD-ROM or other removable disk that is not available. Insert the 'Microsoft Office Small Business Edition 2003' disk and click OK. Use source: Microsoft Office Small Business Edition 2003" 1st got this message after CD was inserted to recover partial file STDP11N. Recovered STDP11N, however, still receiving pop up window with error message each time outlook opens. Had accidentally cleaned up old programs and suddenly this was missing. Reinstalled Microsoft Office Small Business Edition 2003 using install CD. Outlook worked buit keep getting error message pop up each time I open Outlook. Hit ok. Error Message #2: The path 'Microsoft Office Small Business Edition 2003' cannot be found. Verify that you have access to this location and try again, or try to find the installation package 'STDP11N.MSI' in a folder from which you can install the product Microsoft Office Small Business Edition 2003." Hit ok. Back to error message #1 Hit close window Error message #3: Error 1706. Setup cannot find the required files. Check your connection to the network, or CD-ROM drive. For other potential solutions to this problem, see C:\Program Files\Microsoft Office\ OFFICE11\1033\SETUP.CHM Error message #4 I'd created a file under D: drive on an external drive. "The path specified for the file D:...etc.. .pst is not valid. Hit ok. Brings up window to look in My Documents.

  Read the article

• How to connect a USB GDI printer to Linux over a D-Link print server?

  - by jpe

  The setup is the following: +------------+ +-----------------+ +---------+ | HP LJ P1005|--USB--| D-Link DPR-1020 |---LAN---| PC Linux| +------------+ +-----------------+ + +---------+ | +------------+ +--| PC Windows | +------------+ HP LJ P1005 is one of those GDI printers that requires the printer driver to do most of the work for it and therefore is a bit "special". D-Link DPR-1020 is a print server with an Ethernet and an USB port that actually supports printing to challenged (read GDI) printers using a utility called PS-Link. What the utility does is basically mirror a USB port over the network to the print server so that the printer driver and the printer both are happy to talk to each other. The PC-s are notebooks that come and go, i.e. are not there all the time. Is there an equivalent of the D-Link PS-Link utility for Linux that could mirror a USB port over the network for a Linux host? And can the solution be used with D-Link DPR-1020? If not then I basically wasted the money buying the print server because the goal was to share a small printer among a couple of users with diverse operating systems in an office. The print server specs say that it supports Linux and LJ P1005, but the Catch 22 appears to be the solution used for GDI printers... It should be noted that it is possible to print from Linux to LJ P1005 directly over USB. This far sharing involved reconnecting the USB cable to appropriate computer to print. Now one of the desks is separated, so the cable does not work. Searching the net did not yield anything useful. Please do not suggest solutions involving a Windows machine (either virtual or not), my question is whether a solution only involving a Linux machine exists.

  Read the article

• Exchange 2003 ActiveSync problem with certificate

  - by colemanm

  We're having problems getting iPhones to sync properly with SBS 2003 Exchange. When you add a new Exchange ActiveSync account on an iPhone and enter all the pertinent information, it shows a "Verifying Exchange account info" message for a minute or so, then says everything's verified and asks what you want to sync, Mail, Contacts, Calendars... so it looks like it's working. However, when you go to the Mail app and select the Exchange email account, it just shows an "Inbox" folder with nothing in it. When you try refreshing, it attempts for a second, then says "Last Updated" with a timestamp, as if it worked, but there's no mail and no error message/feedback at all. I think I've narrowed it down to some sort of certificate issue, but I'm having trouble finding out where to go from here... I ran MS's Exchange connectivity testing tool with these results: Our cert was purchased from Network Solutions, and I'd already added it to the IIS Default Website for OWA purposes. But this report makes it look like the cert is somehow problematic. I don't know what to do now... Here's a shot of the cert details, just in case:

  Read the article

• Can any iSCSI NAS appliance replicate / clone a LUN to an external drive?

  - by Boden

  I would like to backup using Windows Imaging to some kind of NAS appliance. I believe this will require the NAS to support iSCSI. I would then like the appliance to support the replication of the iSCSI LUN to an external eSATA or USB disk connected directly to the appliance. I've found plenty of NAS appliances that can do iSCSI and replicate to an external drive, but none that I've found thus far can do both at once. That is, the devices can do iSCSI, but then the replication feature doesn't work. The idea here is to backup to an appliance located in a secure office far away from the server room. Offsite backups to external hard drive could be managed from the appliance. The benefits of such a setup would be: 1) very unlikely that fire or random theft would affect both server-room backup and "remote" backup appliance 2) offsite backups could be managed by multiple trusted people without granting access to server room 3) Windows imaging provides poor man's deduplication, so each backup volume can contain a decent backup history. I understand why this would be a non-trivial thing to implement, but I'm wondering if such a thing exists? Preferably a tabletop, low to medium cost device. Alternative solutions welcome. NOTE: I'm backing up very few but very large files, so file replication is not a good option.

  Read the article

< Previous Page | 377 378 379 380 381 382 383 384 385 386 387 388  | Next Page >