Search Results

Search found 1767 results on 71 pages for 'win7'.

Page 39/71 | < Previous Page | 35 36 37 38 39 40 41 42 43 44 45 46 | Next Page >

HP ML350G6 running hyper-V 2008 r2 resets itself every 2 hours

- by GT

The system started resetting itself exactly every 2 hours. These are the messages in the iLO2 log: Informational iLO 2 03/07/2010 20:40 03/07/2010 20:40 1 Server power restored. Caution iLO 2 03/07/2010 20:40 03/07/2010 20:40 1 Server reset. It's not an ASR reset (that would show in the log) Redundant power supplies, swapped but no change. Turned off all virtual machines (i.e. now only running hypervisor) but not OK Boot HP smartstart diagnostics disk, ALL OK Diagnostic disk reports no errors Went back to booting Hypervisor and the problem is back. Seems the hyper-V system disk has got a time based program (virus) causing the reset. I thought the hypervisor had a small attack surface and should be OK. All virtual machines (SBS2008, Win7 and Win XP) and network computers are protected with TrendMicro WFBS. I am about to rebuild the disk (I have backups) but wondered if there were any suggestions to try first???

Read the article
HP ML350G6 running hyper-V 2008 r2 resets itself every 2 hours

- by GT

The system started resetting itself exactly every 2 hours. These are the messages in the iLO2 log: Informational iLO 2 03/07/2010 20:40 03/07/2010 20:40 1 Server power restored. Caution iLO 2 03/07/2010 20:40 03/07/2010 20:40 1 Server reset. It's not an ASR reset (that would show in the log) Redundant power supplies, swapped but no change. Turned off all virtual machines (i.e. now only running hypervisor) but not OK Boot HP smartstart diagnostics disk, ALL OK Diagnostic disk reports no errors Went back to booting Hypervisor and the problem is back. Seems the hyper-V system disk has got a time based program (virus) causing the reset. I thought the hypervisor had a small attack surface and should be OK. All virtual machines (SBS2008, Win7 and Win XP) and network computers are protected with TrendMicro WFBS. I am about to rebuild the disk (I have backups) but wondered if there were any suggestions to try first???

Read the article
How to remove password protection from compressed files

- by Mehper C. Palavuzlar

This has always been a problem for me for a long time. Let's see if any SuperUser can solve this: I have a directory in which there are lots of password protected .RAR files of which I know the passwords. I want to remove the password protection from all of them without extracting the contents. Since each file is larger than 1 GB, decompressing & then recompressing without password encryption is not a good option for me. How can I easily do that? I'm using WinRAR 3.80 on Win7. Any other 3rd party tools are welcomed.

Read the article
How to open ports on modem for better torrent performance

- by Mehper C. Palavuzlar

I've been using utorrent to download and upload torrents for a long time. Recently someone told me that I need to open port(s) for utorrent from my modem settings for better downloading and uploading performance. Is it true? If yes, how can I do that? My utorrent version: 2.0 and the port used for incoming connections: 61829. My modem: Yaksu S200 ADSL router modem and I can reach its settings via web interface. I looked at the settings but they seem a bit complicated to me. Other info you may need to know: I have dynamic IP. I'm using Win7 x64.

Read the article
Windows 7 Software Installation : Siemens Step7 and Siemens SCL

- by Shaharyar

Hello sysadmins, We use Siemens Step7 and SCL for PLC programming in our company. I recently got to install Windows 7 and had yet to find out that the Siemens software suite doesn't install anymore. - Which is a pain... Checking through the setup files, I found following entries in the Setups.ini file: [OS] PlattformIDAllowed=1;2 WinXP=True WinXPExclude=0,Home,1 WinXPWarning=1 WinNETServer=True WinNETServerExclude=Home,0,1 WinNETServerWarning=Home,0,1 Win2003=1 Win2003Exclude=Home,0,1 Win2003Warning=Home,0,1 Win2003R2=1 Win2003R2Exclude=0,1 Win2003R2Warning=0,1 WinVista=1 Win2008=1 Win7=1 I added the last line to try things out and it still provides me the same error.. As far as I know the suite is installed by Install**Shield**. All help would be very appreciated!

Read the article
share one vpn connection through windows rras with other clients

- by KTYP

I'm having a Cisco VPN connection to access our branch office. Since several people using the VPN I'm planing to install the VPN client on one of our server and share it through RRAS to save the licenses (like site - to - site). I install RRAS on a windows 2008 R2 (svrw2k8r2) and made the static routes on client computers. I could able to ping to the VPN's IP on svrw2k8r2 server but they can't seems to connect to the servers in other branch through this setup. Below is my setup My Branch Server: svrw2k8r2 - Windows 2008 R2 IP: 192.168.40.100/24 VPN IP: 10.0.100.12/8 Clients Win7 IP: 192.168.40.101 - 110 / 24 Other Branch Servers IP:10.10.0.10-20/24

Read the article
Can Windows-Security-SPP block execution of .exe?

- by Kirk Marple

We're seeing a strange situation, where some executables won't run from a Windows command prompt (running as admin). Just running the command (say, filename.exe) gives no response on the console. No errors, no output, nothing. If we copy over the same Windows .exe from a different folder, it "magically" starts working, and we see the default console output. (Happens both on Win7 x64, and Win2008R2 x64. Application is running as 32-bit process.) At the time when it accesses the .exe, I can see events in the application and system logs regarding Windows-Security-SPP, and it makes me believe that the .exe is being blocked from execution. Does this sound familiar?

Read the article
Welcome files are not loaded! Need help with Railo, mappings and J2EE configuration!

- by mrt181

I have installed a J2EE Server (tried it with Glassfish3, Tomcat6 and Resin4) on Win7 64bit and deployed Railo3.1. I have then added a virtual host to the J2EE server, i.e. Resin: <host host-name="railo"> C:/resin/webapps/railo In the Railo Admin i have added this mapping: Virtual Physical / C:/webapps/ When i access http://railo:8080/ my index.cfm welcome file in C:/webapps/ is loaded (index.cfm is definded in Railos web.xml). When i try to access http://railo:8080/test which contains the same index.cfm i get an 500 Servlet Exception java.io.FileNotFoundException: C:\webapps\test (access denied) (on all J2EE Servers i tried so far). http://railo:8080/test/index.cfm works fine. I already tried to add index.cfm to Resins welcome-file-list in app-default.xml to no avail. I want to be able to access deployed apps without this url: http://localhost:8080/app/ Instead i want to use this: http://app:8080/

Read the article
Windows 7 locked out account

- by Lukas

I have a Win7 x64 computer. There was only one account (mine, created at installation, password protected, full administrative access with UAC enabled). To speed up the startup + login process I went to control userpasswords2 and unchecked that users need to enter password. By this operation my account has been changed to Guest type and an Administrator account has been created. This Administrator account has a small overlay icon with a downwards pointing arrow. My original password did not work; if I try leaving the password blank it says something like "Your account has been disabled. Contact your administrator." Contacting myself surprisingly did not help. As my account (which I am still able to access) is Guest, I have no rights to do anything. Is there a way to get my access back without reinstalling?

Read the article
Browser won't connect to svn server

- by devpi

This has been driving me nuts. For some reason, I can't access my svn repository using a browser in this laptop that I'm using right now (firefox & ie) The connection just times out. I'm at home right now and the server is in another room. It connects OK there and it also connects OK in my virtual machine in this same laptop. I'm pretty stumped right now and can't figure out why this is happening. I've also checked the proxies and I'm 100% sure I'm not using any at all. The virtual machine running on this laptop is XP 32bit and this one is a Win7 64 bit. Thanks

Read the article
Can't get Intel drivers for ASUS P6T Deluxe

- by Alex K

Hi everybody, A few days back my Win7 Ultimate started bugging me to install the RAID drivers for my ASUS P6T Delux. Fine, I'm all for having up to date drivers even for stuff I don't use. The problem is that the drivers I download from both ASUS support site here and the ones I get directly from Intel (can't post the second link, since I have less than 10 rep, but it's the first hit for "Intel(R) Matrix Storage Manager Driver" on google) say that my system does not meet the minimum system requirements. Impossible, I would think, what with it having the X58 chipset and the Windows version is supported one. Has anyone encountered something like this before? Any clues on how to solve this would be much appreciated. Thanks!

Read the article
VPN networking issue

- by DuncanDavies

I have 2 servers hosted in the cloud. One an application server, one a VPN server, both running Win2008. Both have a local IP address assigned by DHCP in different network subnets, 10.227.55.0 (VPN) and 10.231.5.0 (App Server). These servers can ping each other. My VPN client connects in to the VPN server (using a L2TP connection on a Win7 client). It is assigned an IP Address from the VPN server's static pool (the VPN server takes 192.168.100.1, the client is given 192.168.100.2). The client can ping both the 192.168.100.1 address of the VPN server, and its 'local' IP address (10.227.55.X). What the client can't do is ping the App Server. How can I configure routing so that my client can access the App Server, without hard-coding any of the DHCP IP addresses anywhere? thanks Duncan

Read the article
Win 7 Privilege Level (Run as administrator) via GP or command line

- by FinalizedFrustration

Is there a way to set the Privilege Level for legacy software via group policy or on the command line? I have some legacy software, which we unfortunately cannot move away from. This software requires administrator access. I know I can go into the Properties dialog and check "Run this program as an administrator" on every single instance on every single one of my workstations, but that gets old after the 30th install. If I had my way, we would dump this software, find some software that did what we needed, was fully compliant with Win7 security best-practices and give everyone limited user accounts... However, I am not the boss, so everyone gets administrator accounts. Given that, I suppose I could just tell everyone to open the context menu and choose "Run as administrator", but we have some very, very, VERY low-tech users, and half of them might just choose "Delete" instead. Anyone know of a way to set this option on the command line? or better yet, through Group Policy?

Read the article
win xp client, win 7 host, only xp drivers

- by brett

I have a win 7 64 bit box which has xp on it in a vmware module and also the win7 version. I can use my old usb wifi card under virtual xp as i have the wifi drivers, but apparently the manufacturing company never made any further drivers, nor did it release the source code. Is it possible to get networking between the client and the host, so that my host can browse etc? I thought the microsoft loopback adapter might be the answer but ever example i can find of it's use describes a setup where the host is connected fine and needs to route data to the client as well.

Read the article
New installation - Win 7 or directly Win 8?

- by Horst Walter

My laptop's hard disk is gone, so I need to re-install my Windows. Would it be a good idea to directly install Win8 (so actually the preview). Is there any known incompatibility with Win7 which would be a show stopper? I have a Dell XPS laptop, I do not expect any driver issues since the series is pretty much mainstream. Would the Win8 preview become Win8 RTM automatically by updates, or would I need to re-install Win8 RTM. This would be the no-go for me. The Win8 preview does not require a key, so I guess it becomes Win 8 RTM and then needs to be activated (which is what I want). Basically the idea is, I have to install windows anyway, so why not using the latest version?

Read the article
Multiple User VPN

- by Aaron

I am looking for a cheap or free solution to be able to connect multiple people via VPN to a host computer. Each person should not be able to see what the others are doing while logged in. Is this possible and if so where do I start my hunt? Aaron Update: I was not sure what server, was just thinking of doing it on say a win7 desktop. Just looking into having 2-3 users have access to a program without each seeing each other. Basically, I know nothing and want to know if this is a possibility for me. lol

Read the article
USB hard drive doesn't graceful power off after eject on Windows 7

- by Sim

I have a couple of Seagate FreeAgent Go external USB hard drives and would like them to gracefully power off after ejecting in Windows 7. With Windows XP a few seconds after they are ejected they gracefully power off. When ejecting them on Windows 7 they just stay on and have to be physically disconnected before they lose power. I have checked the hard drive removal policy and it is set to quick removal. I have also looked in the Seagate forums but I couldn't find any info on this so I thought I'd ask the SuperUser community on any ideas why the difference and how to get the same behaviour in Windows 7 as in XP? Update: I am finding that this also happens with USB thumb drives as well. My current theory is that there were changes to the driver model with Vista/Win 7 that haven't been reflected in the device drivers yet. So things that worked under XP don't under Win7 as the drivers haven't been updated for the new model. Does that sound right?

Read the article
Tunneling traffic through two VPN hops/tunnels.

- by Roberto Sebestyen

I am a web developer, and I find myself often working from home. But when I do, I am forced to Remote Desktop to the Office desktop computer and work from there. The reason is because the application I am working on needs to connect to servers at a Data Center via a VPN from the Office Desktop. HomeDesktop (Win7) --- PVN --- OfficeDesktop(WinXP) --- VPN --- Data Center What I would really like to do is, I would like to find a way to be using my Home desktop developing on that, and whenever my computer tries to access servers on the Data Center, I would like to tunnel that traffic through the two VPN tunnels separating me and the Data Center. I have admin privileges on both Office Desktop and Home Desktop, but I do not have any admin privileges in the Data Center. So what kind of tunneling solution could I use here? Is it even possible?

Read the article
Automatically save/download e-mail body to disk

- by CatamountJack

Is there a program that will allow me to connect to my mail server (IMAP) and automatically save certain new e-mails to disk? Multiple times a day I receive automated e-mail updates about pending jobs from a system that processes some information for us. The data in these e-mails is written as plain-text within the body of the message. I would like to download the newest message, parse it, and display it on my desktop. The last two parts I can manage ok - it's just the automatic downloading that is posing a challenge. I don't use Outlook (I do use Thunderbird), but would prefer not to have the client open to make this happen. I'm currently running Win7.

Read the article
3ware RAID in Windows 7

- by scribbles

Just moved a 3ware 9500S-8 raid card and a few drives from my linux box into my win7 box. Windows Updates picked up the 3ware driver and installed it. After a reboot I checked Disk Management and it shows the array as one solid drive with the correct size. The only issue is that its not assigned a drive letter and when I right click on it my only option is to Convert to Dynamic Disk... From what I've read this is not something I want to do. What are my options?

Read the article
Activate Windows XP in VMWare?

- by Zeno

Running Windows XP in VMWare, how should activation be handled? Last time I did this, I do not remember having to do any activation. Now it is asking me to activate Windows XP. Am I suppose to buy and use a real WinXP key? What is this about a "Windows XP Mode" I'm hearing about that you can enable in VMware to activate it? The availability of Windows XP Mode is equivalent to a free license to Windows XP operating system. My host machine runs Win7. My goal is to get WinXP running in VMWare the simplest way, but this activation is giving me issues (such as that WinXP doesn't seem to be sold anymore). I Googled around and found that VMWare has a xpmode.enabled = "TRUE" feature which instantly activates Windows XP (with limits, like only once), but I do not know anything about it or how to use it.

Read the article
Wikipedia Images don't show up in browsers

- by mantra

It's a weird issue with wikipedia which had left me frustrated. When I go to wikipedia, with different browsers ( IE8, Chrome3, Opera10 ) no image in the site will show up. Even right-clicking the image to ( show, save, open in new tab/window ) will return nothing except when open in new tab/window I'll get a black horizontal line across the page. All my browsing across the web goes flawlessly, and every image in every site show up normally except in the wikipedia site. I have win7 ultimate with all updates.

Read the article
Exporting Speed Dial settings from within Firefox into Chrome Speed dial...

- by Paul

Win7 Home Prem 32-bit I usually use Firefox as my browser of choice and have been using the Addin Speed Dial for ages. I have many sites added on multiple tabs within it. I have just installed the Google Chrome browser which also has the Speed Dial Extension. Is there a way to export/import/copy/sync my Speed Dial settings i have in Firefox to the Speed Dial extension in Chrome? I know i can export from Speed Dial in Firefox but can't see any easy way to import from Speed Dial in Chrome.

Read the article
Disable (or switch off) a network interface on windows but keep the "plug and play"

- by Leandro

I'm looking for a good workaround to do this on Windows 7 and Windows XP: Disable or make ineffective the network interface (ETH, WIFI, any NIC). If the user connect his ETH cable, the network interface enable again. Important Notes to take care: I'm working with wmic on Win7 (through the command line) I'm working with devcon on WinXP (through the command line) I'm specifically working with the .NET Framework 2.0 on C# but this is just for informational purposes. I know that an event won't help me to detect it (if there is a way or workaround to do this I don't know it). The real problem is that when I disable the NIC, I can't know if the user connects his cable or has a wired network. This is why I am looking for a workaround. I'll treat suggestions as answers if no direct answer exists. I'll provide any extra detail necessary.

Read the article
Enabling Multiple Monitor Support from Terminal Services/Remote Desktop over Citrix

- by Nicolas Webb

Our Remote Desktop/Terminal Services solution where I work relies on Citrix for machines not connected via the VPN. We're using Citrix Xen server (I'm pretty sure) and I'm going to try to connect to a Windows 7 Host (my work computer) and I think the RDC client runs on a Win2003 host (exposed via Citrix). Is it possible to take advantage of Windows 7 multiple monitor support for RDC with this setup? Would I need to try getting my Citrix guys to have a different host machine for the RDC (Win2008, or Win7?)? I'm probably going to connect using the OS X Citrix client, but I'd be willing to BootCamp/Fusion up a Windows instance to work remotely, as well. I really want to be able to use multiple monitors remotely. It does "span" multiple montiors currently (I have a 3000x1024 desktop, for example) but I'd rather it be "true" multiple monitor instead of one giant desktop, if possible.

Read the article

< Previous Page | 35 36 37 38 39 40 41 42 43 44 45 46 | Next Page >