Search Results

Search found 12912 results on 517 pages for 'auto suggest'.

Page 390/517 | < Previous Page | 386 387 388 389 390 391 392 393 394 395 396 397  | Next Page >

• Dedicated Mouse and Keyboard on Virtual Box VM

  - by Myersguy

  To all super users, Currently I am trying to run virtual box on my second monitor, with a dedicated mouse and keyboard. However, doing so has not proven easy. There has been times where the mouse works, but not the keyboard, vice versa, or nothing works at all. The biggest problem I am running into is this: When enabling the USB mouse and keyboard from the VM, I get an error: 'USB Device is busy with a previous request.' The only thing that is using second mouse and keyboard, however, is Windows. The other error I have received stated that the VM was unable to create a proxy for the device. Additionally, the VM occasionally will disable the secondary keyboard entirely, requiring me to unplug and replug it into my PC to re-enable it again. Keyboard auto-capture is disabled, and while a solution I was reading online stated to turn off mouse integration, that option is grayed out on my machine. Any help would be appreciated. Thanks. /firstquestion.

  Read the article

• Server not resolving after restart

  - by DomainSoil

  I restarted our server today, and now cannot for the life of me get anything to resolve... I suspect it has something to do with our routes. I've tried numerous Google results to no avail. Here is as far as I've gotten: [root@www ~]# route -n Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.101 0.0.0.0 255.255.255.255 UH 0 0 0 eth1 0.0.0.0 192.168.1.101 0.0.0.0 UG 0 0 0 eth1 Things you need to know: Our server (CentOS 6.3) runs two virtual machines, one live, and one development. They mirror each other as much as possible, but I can't find where I've went wrong with the live server. The dev server works fine. [root@www ~]# ifconfig eth1 Link encap:Ethernet HWaddr xx:xx:xx:xx:xx:xx inet6 addr: xxxx:xxx:xxxx:xxxx:xxxx/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:118206 errors:0 dropped:0 overruns:0 frame:0 TX packets:165 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7825749 (7.4 Mib) TX bytes:7146 (69.2 KiB) Interrupt:28 [root@www ~]# /etc/init.d/network status Configured devices: lo Auto eth0 Currently active devices: lo eth1 If there is any other information you need, please don't hesitate to ask!

  Read the article

• #550 5.1.1 RESOLVER.ADR.ExRecipNotFound; not found ##

  - by gtaylor85

  I've searched serverfault and found this question pop-up quite a bit. Unfortunately others problems aren't exactly like mine, and because I'm a true beginner I wanted some more "specific to me" help. If you don't mind. I just set-up a new computer for a user. Copied over her auto-populate and archive emails. Her email, for the most part, works fine. But when she tries to send anything to [email protected] she gets the #550 5.1.1 error. If she uses the exchange webapp she does not have the issue. I can send email to BSMITH, and so can everyone else. The user, as far as I can tell from the EMC reports, is the only person having emails sent back to them and only from BSMITH. I have googled the crap out of this, and attempted some of the solutions to no avail. I've looked for the bmith account in the disabled accounts and copied and attempted to add "IMCEAEX-_O=CHILD+20STUDY+20CENTER_OU=FIRST+20ADMINISTRATIVE+20GROUP_CN=RECIPIENTS_CN=BSMITH@mydomain.com" as an X500 email. I honestly am just following instructions though and I don't really understand what it is I'm doing. Diagnostic information for administrators: Generating server: FS2.FS1D.local IMCEAEX-_O=CHILD+20STUDY+20CENTER_OU=FIRST+20ADMINISTRATIVE+20GROUP_CN=RECIPIENTS_CN=BSMITH@mydomain.com #550 5.1.1 RESOLVER.ADR.ExRecipNotFound; not found ## BTW I love this site and only found out about it a few weeks ago. My girlfriend now loves the photo.stackexchange. So thanks for such a helpful community.

  Read the article

• Can’t connect to SQL Server 2008 - looks like Shared Memory problem

  - by Proposition Joe

  I am unable to connect to my local instance of SQL Server 2008 Express using SQL Server Management Studio. I believe the problem is related to a change I made to the connection protocols. Before the error occurred, I had Shared Memory enabled and Named Pipes and TCP/IP disabled. I then enabled both Named Pipes and TCP/IP, and this is when I started experiencing the problem. When I try to connect to the server with SSMS (with either my SQL server sysadmin login or with windows authentication), I get the following error message: A connection was successfully established with the server, but then an error occurred during the login process. (provider: Named Pipes Provider, error: 0 - No process is on the other end of the pipe.) (Microsoft SQL Server, Error: 233) Why is it returning a Named Pipes error? Why would it not just use Shared Memory, as this has a higher priority order in the list of connection protocols? It seems like it is not listening on Shared Memory for some reason? When I set Named Pipes to enabled and try to connect, I get the same error message. My windows account is does not have administrator priviliges on my computer - perhaps this is making a difference in some way (as some of the discussions in this post about an "SuperSocketNetLib\Lpc" registry key seems to suggest). I have tried restarting the SQL Server service, by the way, and also tried to get someone to log onto the machine with an admin account to restart the SQL Server service. Still no luck.

  Read the article

• Debian: Unable to mount a second drive as a subdirectory inside of another partition.

  - by jkndrkn

  Hello. I have the following /etc/fstab: # /etc/fstab: static file system information. # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc defaults 0 0 /dev/md1 / ext3 defaults,errors=remount-ro 0 1 /dev/md0 /boot ext3 defaults 0 2 /dev/md5 /home ext3 defaults 0 2 /dev/md3 /opt ext3 defaults 0 2 /dev/md6 /tmp ext3 defaults 0 2 /dev/md2 /usr ext3 defaults 0 2 /dev/md4 /var ext3 defaults 0 2 /dev/md7 none swap sw 0 0 /dev/sdc /home/httpd ext3 defaults 0 2 /dev/hda /media/cdrom0 udf,iso9660 user,noauto 0 0 /dev/sdc1 /mnt/usb/backup-1 auto defaults 0 0 I am unable to get /dev/sdc/ to mount at /home/httpd/ on reboot. The /home/httpd/ directory exists. Mounting via mount -t ext3 /dev/sdc /home/httpd works just fine. Mounting via mount -a generates the following error message: mount: you must specify the filesystem type This is, incidentally, the same message that I see while booting. The error message goes away if I comment out the line in fstab starting with /dev/sdc.

  Read the article

• Wordpress on Apache is redirecting all https to http

  - by Krist van Besien

  I have a problem with a wordpress site on a server I admin. I don't know anything about wordpress however. My problem is that we want the site to be accessed over https, bot somehow all requests to https:// URLs are answered by the server with a 302, redirecting to http. The wordpress site itself is configured to use https, and we see that in the pages that are generated the links are all https links. In the apache config there are no rewrite rules and no redirects. However, any request to a https:// URL is answered with a redirect to the equivalent http URL. And I really would like to know where these redirects are coming from, what is generating these redirects. I've increased the loglevel on the webserver to DEBUG, but did not get any info there. I tried to enable debug logging in wordpress per the recipy I found here: http://codex.wordpress.org/Debugging_in_WordPress But did not get a debug.log file in the directory where one should appear. I'm really at a loss here, and need to fix this urgently. Any hints as where to start looking? Apache is 2.2.14 on Ubuntu. There are several other virtual hosts on this server, using php and https without any problem... Edit: I created a small info.php script and dropped that in the webservers' root. Calling this yields the output of the script, no redirect is generated. This suggest that it's not the webserver, but wordpress that is doing it. A second thing I noticed is that the redirect comes with several cookies, one of which has "httponly" set. Could that be it?

  Read the article

• Nginx , Apache , Mysql , Memcache with server 4G ram. How optimize to enought memory?

  - by TomSawyer

  i have 1 dedicated server with Nginx proxy for Apache. Memcache, mysql, 4G Ram. These day, my visitor on my site wasn't increased, but my server get overload always in some specified time. (9AM - 15PM) Ram in use is increased second by second to full. that's moment, my server will get overload. i have to kill all apache , mysql service and reboot it to get free memory. that's the circle. here is my ram in use at the moment 160(nginx) 220(apache) 512(memcache) 924(mysql) here's process number 4(nginx) 14(apache) 5(memcache) 20(mysql) and here's my my.cnf config. someone can help me to optimize it? [mysqld] datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock user=mysql skip-locking skip-networking skip-name-resolve # enable log-slow-queries log-slow-queries = /var/log/mysql-slow-queries.log long_query_time=3 max_connections=200 wait_timeout=64 connect_timeout = 10 interactive_timeout = 25 thread_stack = 512K max_allowed_packet=16M table_cache=1500 read_buffer_size=4M join_buffer_size=4M sort_buffer_size=4M read_rnd_buffer_size = 4M max_heap_table_size=256M tmp_table_size=256M thread_cache=256 query_cache_type=1 query_cache_limit=4M query_cache_size=16M thread_concurrency=8 myisam_sort_buffer_size=128M # Disabling symbolic-links is recommended to prevent assorted security risks symbolic-links=0 [mysqldump] quick max_allowed_packet=16M [mysql] no-auto-rehash [isamchk] key_buffer=256M sort_buffer=256M read_buffer=64M write_buffer=64M [myisamchk] key_buffer=256M sort_buffer=256M read_buffer=64M write_buffer=64M [mysqlhotcopy] interactive-timeout [mysql.server] user=mysql basedir=/var/lib [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid

  Read the article

• The script not working as expected files dump path

  - by user3319390

  I have a script needs to be dump matching cname from my file contains and then matching scode to dump file to $cname/$year/$month/$day/ into files like access and error logs #!/bin/sh #base_dir="/home/vizion/Desktop" path="/home/vizion/Desktop/adn_DF9D_20140515_0005.log" name=$(basename "$path" ".log") for x in *.log; do year=${x:9:4}; month=${x:13:2}; day=${x:15:2}; done while read -r line do cname=$(echo ${line} | awk '{split($7,c,"/"); print c[3]}') scode=$(echo ${line} | awk -F"[ ]" '{print $9}') [[ ! -d "$cname/$year/$month/$day" ]] && mkdir -p "$cname/$year/$month/$day/" [[ ( ${scode} -ge 200 ) && ( ${scode} -le 399 ) ]] && { # [[ ! -d "$cname/$year/$month/$day" ]] && mkdir -p "$cname/$year/$month/$day/" echo ${line} >> /home/vizion/Desktop/$cname/$year/$month/$day/${cname}_${name}_access.log } [[ ( ${scode} -ge 400 ) && ( ${scode} -le 599 ) ]] && { [[ ! -d "$cname/$year/$month/$day" ]] && mkdir -p "$cname/$year/$month/$day" echo ${line} >> ${cname}_${name}_error.log } done < $path i am able to filter logs but not not dumping the exact location It's going other locations suggest to me correction in script

  Read the article

• Suggestion regarding pointing domains to a dedicated server.

  - by Bizz

  I recently got a dedicated server and I am still at a learning stage. So please bear with me. I wanted to have 3 domains pointed to my server, but initially I asked them the process to point me one and they responded with: Hello, I can set that rDNS for you. Please make sure the domain is pointed to our name servers at godaddy. They are: ns1.xxxxx.net ns2.xxxxx.net After this is done, please allow up to 24 hours for global propagation. Alternatively, we can host your DNS for you if you prefer. What is the domain you would like xx.xxx.xx.xx to resolve to? I then asked him to point one of my domains. They responded, Did you want us to host your dns for that domain or just an rDNS record? They also said, Hosting your DNS is a free service here. We can only do 1 domain per IP. IF you would like to purchase additional IPs, they are $1/IP per month. I personally dont want to host DNS myself. Neither mail server. I have a single IP so far. It will then start to get expensive if I want to host 25 from these guys. I am still in the trial period. Does this seem reasonable as far as pricing goes? If I want to have some one host DNS and mail server, this is getting super expensive. Email hosting from rackspace starts at $2 per mail address, but from then on, its the same if you want added features such as archiving etc; What would you suggest I do if I am on a shoe string budget but I also want to avoid hassle of doing it myself and I only have 3 domains so far and I would need few mail addresses for each of them.

  Read the article

• How to flash Dell Precision 390 from linux (debian)

  - by malat

  I am trying to update my BIOS: $ sudo dmidecode -s bios-version 2.1.2 With a newer one: 2.6.0. I went to this page Dell Precision System BIOS, 2.6.0 After downloading the file WS390-020600.BIN, here is what it states: $ ./WS390-020600.BIN --help Usage: WS390-020600.BIN [options] Options: --help Print this text. --version Print package versions. If no options, update the BIOS. and $ ./WS390-020600.BIN --version Dell BIOS Update Installer 1.2 Copyright 2006 Dell Inc. All Rights Reserved. ./WS390-020600.BIN: 60: ./WS390-020600.BIN: ./flash: not found Does anyone knows where this flash command can be found ? Update: it looks like this is a self-extracting archive (need bash as per comment in header). $ head -30 WS390-020600.BIN [...] Extract() { tail -n +`awk '/^__ARC__/ { print NR + 1; exit 0; }' $0` $0 | gzip -cd >$_PRG So the flash command should have been auto-generated, however the above command does not appear to be running as original author intended. I do not see anything wrong with the command though.

  Read the article

• USB 3.0 ports backwards compatibility problems with 2.0 devices?

  - by AaronLS

  I see some info on the net that suggest that I should be able to get my USB 2.0 devices to work in 3.0 ports. I only have two 2.0 ports on my new computer, and six 3.0 ports. I have installed drives. There's two different drivers, I guess some of the ports are supported by the intel board and some supported by some other chipset on the motherboard. I however have yet to get any of the 3.0 ports to work, and my brother had had the same issue with his devices not working in 3.0 ports on his computer. So I am beginning to wonder if the backwards compatibility isn't reliable for some reason. Maybe manufacturers opting not to implement 2.0 support on the 3.0 ports. I understand that physically the wiring is there, but that is only half the story. Beyond my brother's and my own computers (different motherboards/everything), I have yet to see a 2.0 device work in a 3.0 port. Is there any reason for this apparent device incompatibility? I.e. looking for responses that would indicate what areas to explore for issues or if there is any known cases of manufacturers deviating from spec in hardware or drivers. I am aware it's "supposed" to work :) Update: Does this have any relation to "USB Legacy Support" options in the BIOS? There several options combinations of options with "USB Legacy Support" and "USB 3.0 Legacy Support" and the description for these is a bit confusing, sounds like a bad translation.

  Read the article

• postfix email gateway

  - by k-h

  I am setting up a postfix email gateway. It will not hold any mail but will accept email for my domain and forward it to another internal mailserver and relay mail out from the internal server. One of the main problems is that I am working on a live running system and this will be an upgrade so I am using a test domain which I will change at some point to the real domain. I tried various methods but found the simplest way (that worked) was to use a script to create an aliases file (from ldap entries). There are various problems with this method. The main one being that the entries can't be of the simple form [email protected] because the gateway doesn't know where to send them. They have to be of the form: [email protected]. What I would like doesn't seem hard but I can't get my head around the postfix documentation. There seem to be various ways but none of them seem to work. Most of the examples I have found on the web assume the mail is going to end up on the server. I want a list of users somewhere, preferably of the form: user1, user2, etc rather than [email protected] (I can easily generate this list) and I would like postfix to forward all email to example.com to a particular server: ie realmailserver.example.com. Can anyone suggest clues as to how I might do this?

  Read the article

• Redhat Linux password fail on ssh

  - by Stephopolis

  I am trying to ssh into my linux machine from my mac. If I am physically at the machine I can log in with my password just fine, but if I am sshing it refuses. I am getting: Permission denies (publickey,keyboard-interactive) I thought that it might be caused by some changes that I recently made to system-auth, but I restored everything to what I believe was the original format: #%PAM-1.0 # This file is auto-generated. # User changes will be destroyed the next time authconfig is run. auth required pam_env.so auth sufficient pam_fprintd.so auth sufficient pam_unix.so nullok try_first_pass auth requisite pam_succeed_if.so uid >= 500 quiet auth required pam_deny.so account required pam_unix.so account sufficient pam_localuser.so account sufficient pam_succeed_if.so uid < 500 quiet account required pam_permit.so password requisite pam_cracklib.so try_first_pass retry=3 password sufficient pam_unix.so md5 shadow nullok try_first_pass use_authtok password required pam_deny.so session optional pam_keyinit.so revoke session required pam_limits.so session [success=1 default=ignore] pam_succeed_if.so service in crond quiet use_uid session required pam_unix.so But I still could not ssh in. I tried removing my password all together and that didn't seem to help either. It still asks and even entering an empty string (nothing) it still fails me out. Any advice?

  Read the article

• pgpool2+streaming replication failover on only 2 servers?

  - by aneez

  I am trying to configure pgpool2 and postgresql 9.1 to handle failover. I currently have streaming replication running, and are using pgpool2 for read-only load balancing. I have 2 servers in my setup, both running postgresql - 1 master and 1 slave. The master is also running pgpool2. My question is how do I configure this setup to handle failover? Specifically in the case that the master crashes, and the slave has to take over and run pgpool2 as well. Most documentation and examples I have been able to find assumes that pgpool2 is running on a separate server and thus "never" crashes. I may or may not be attacking the problem using the wrong tools. In my production setup I have a total of 3 identical servers all in independent locations. The main goal of the setup is to achieve a high uptime. Thus failover should be automatic, and bringing a failed node back up should cause only minimal downtime. I want all 3 nodes to be as close to identical as possible, and be able to run with just 1 or 2 nodes available. And if possible I want to use load balancing to improve performance. If anyone can help me gain some insight into how to do this using my current setup or suggest a different/better setup. Thank you!

  Read the article

• Almost All Logical Volumes Disappeared - Recovery?

  - by Alex

  We had a hard disc crash of one of two hard discs in a software raid with a LVM on top. The server is running Citrix xenserver. On the hard disk which is still intact, the volume group gets detected well, but only one LV is left. (some hashes replaced by "x") # lvdisplay --- Logical volume --- LV Name /dev/VG_XenStorage-x-x-x-x-408b91acdcae/MGT VG Name VG_XenStorage-x-x-x-x-408b91acdcae LV UUID x-x-x-x-x-x-vQmZ6C LV Write Access read/write LV Status available # open 0 LV Size 4.00 MiB Current LE 1 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:0 root@rescue ~ # vgdisplay --- Volume group --- VG Name VG_XenStorage-x-x-x-x-408b91acdcae System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 4 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 0 Max PV 0 Cur PV 1 Act PV 1 VG Size 698.62 GiB PE Size 4.00 MiB Total PE 178848 Alloc PE / Size 1 / 4.00 MiB Free PE / Size 178847 / 698.62 GiB VG UUID x-x-x-x-x-x-53w0kL I could understand if a full physical volume is lost - but why only the logical volumes? Is there any explanation for this? Is there any way to recover the logical volumes? EDIT We are here in a rescue system. The problem is that the whole server does not boot (GRUB error 22) What we are trying to do is to access the root filesystem. But everything was in the LVM. We have only this: (parted) print Model: ATA SAMSUNG HD753LJ (scsi) Disk /dev/sdb: 750GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 750GB 750GB primary boot, lvm And this 750GB LVM volume is exactly what we see on top.

  Read the article

• Are these hardwares compatible?

  - by Tom Kaufmann

  I am trying to upgrade my new machine but I want to do it myself. This is my 1st attempt at building system. After carefully reading reviewing feedback and my budget I have decided to select the below listed components. Can anybody let me know are they compatible or not? Transcend 64 GB 2.5" SATA Solid State Drive Asus GeForce GTX550 1GB DDR5 ENGTX550 TI DI/1GD5 Graphics Card Seagate Barracuda 1 TB HDD Internal Hard Drive Cooler Master eXtreme Power Pro 600 Power Supply Intel Core i5 2500K Sandy Bridge 3.30 GHz 95 W 4 Core Desktop Processor Intel DX79TO Motherboard Corsair CMZ8GX3M2A1600C9 8 GB DDR3 SDRAM 1600 MHz Dual Channel Kit Desktop Memory Sony AD-7260S-ZS Internal DVD Writer - Black Cooler Master Hyper TX3 EVO Intel CPU Cooler Cooler Master Elite 335U Cabinet LG E2051T 20.1 Inch SuperSlim Monitor Is any of these hardware components incompatible with I5 2500K? If you have any other suggestions for selecting any other harwdware that can boost up my performance or lower my cost while having the same performance, please suggest. But my primary questions is whether they are compatible or not! Any help is appreciated. Thank you.

  Read the article

• How should an experienced Windows SysAdmin learn Linux? [closed]

  - by Systemspoet

  I have a new hire starting in a few weeks who is an experienced Windows SysAdmin. I think he's fairly senior on the Windows side, with a pretty deep AD understanding and experience with Exchange 2007, 2010, and exchange migrations. He's done a little PowerShell but I suspect more of the "run this command to do this" variety then "write a script to do this" sort. However, we are a mixed shop and (he knows this) I expect him to become a reasonably competent Linux SysAdmin over time. I'm looking for good starting points to bring him along. I have over ten years of Linux/UNIX experience, so it all sort of seems intuitive to me, but I've been thinking about the toolkit you actually need to be productive in the Linux CLI world. Just to be able to use the machines at all, off the top of my head... vi Basic CLI stuff -- move around, rename files, copy files, tar, gzip, changing passwords, finding relevant manpages, keep track of where you are, find things in your history, etc, etc. More advanced things that I take for granted but are actually pretty hard -- doing things with 'find', extracting relevant text via 'awk' and/or 'cut', knowing when to use 'grep' and when to use 'grep -e' or 'egrep'. Distribution specific stuff... compiling software, rpm, yum, apt-get, you name it. This all seems pretty basic to me, but when I think back to 1995 when I was first learning my way, some of those things took me years to master. So my question is -- where should I send him to pick up those skills? I'm not just thinking of classes, but rather also websites and books? Where do you all suggest as a starting point for picking up Linux skills?

  Read the article

• Providing access to a no-www website in an active directory environment

  - by oasisbob

  Our website is hosted externally, off our network. The canonical URL is a is intentionally lacking www, and will 301 redirect any requests containing www to the canonical URL. So far, so good. The problem is providing access to the website from within our LAN. In theory, the answer is simple: add a host record in DNS pointing foobarco.org to the external webhost. (eg foobarco.org -- 203.0.113.7) However, Our active directory domain is the same as our public website (foobarco.org), and AD appears to periodically auto-create host (A) records in the domain root corresponding to our domain controllers. This causes obvious problems: users on the LAN attempting to access the website resolve the domain controllers instead. As a stop-gap measure we're overriding DNS using the hosts file on clients, but this is a quick hack that doesn't scale well. The hosts-file hack hasn't broken anything obvious, so I doubt that this behavior is essential to AD operations, but I haven't found a way to disable it. Is it possible to override this behavior?

  Read the article

• What is the typical maximum number of database connections for Oracle running on Windows server ?

  - by Sake

  We are maintaining a database server that serve a large number of clients. Each client typically running serveral client-applications. The total number of connections to the database server (Oracle 9i) is reaching 800 connections on peak load. The windows 2003 server is starting to run out of memory. We are now planning to move to 64bit Windows in order to gain higher memory capability. As a developer I suggest moving to multi-tier architecture with conneciton pooling, which I believe is a natural solution to this problem. However, in order to support my idea, I want the information on: what exactly is the typical number of connections allowed for Oracle database ? What is the problem when the number connections is too high ? Too much memory comsumption ? or too many sockets opened ? or too many context switching between threads ? To be a little bit specific, how could Oracle Forms application scale to thousand of users without facing this problem ? Shall Oracle RAC applied to this case ? I'm sure the answer to this question should depend on quite a number of factors, like the exact spec of the hardware being used. I'm expecting a rough estimation or some experience from the real world.

  Read the article

• 3 Monitor PCI-e Graphics card (without tremendous pain)?

  - by N Rahl

  As we are all painfully aware, the only way to get multiple monitors AND compositing (Compiz) on Linux is to use a single graphics card that can drive both (or in my case all three) screens. I bought a Radeon 5750 specifically because it claims to able to drive 3 monitors. I can plug in 3 monitors (2 DVI, 1 HDMI) and the Catalyst Control Center shows all 3, but only 2 can be enabled at a time. The exact message is: The current settings cannot be applied. Possible issues may include: - Display(s) cannot be enabled. - Setting(s) cannot be applied due to insufficient video memory. So I'm going to assume that either the 5750 doesn't support 3 monitors, OR, more likely, ATI couldn't be bothered to add that support to their Linux drivers. So this is a multipart question: First, can anyone suggest a PCI Express Graphics card that can run 3 screens on linux without tremendous pain? I'm looking for something where you install the driver and all three screens "just work". Does such a card exist? Second, if you have a 5750, have you been able to get it to do 3 monitors? I'm running Ubuntu 10.04 at the moment.

  Read the article

• Deployment and monitoring tools for java/tomcat/linux environment

  - by Ran

  I'm a developer for many years, but don't have tons of experience in ops, so apology if this is a newbe question. In my company we run a web service written in Java mainly based on a Tomcat web server. We have two datacenters with about 10 hosts each. Hosts are of several types: Dababase, Tomcats, some offline java processes, memcached servers. All hosts are Linux CentOS Up until now, when releasing a new version to production we've been using a set of inhouse shell script that copy jars/wars and restart the tomcats. The company has gotten bigger so it has become more and more difficult operating all this and taking code from development, through QA, staging and to production. A typical release many times involves human errors that cost us precious uptime. Sometimes we need to revert to last known good and this isn't easy to say the least... We're looking for a tool, a framework, a solution that would provide the following: Supports the given list of technology (java, tomcat, linux etc) Provides easy deployment through different stages, including QA and production Provides configuration management. E.g. setting server properties (what's the connection URL of each host etc), server.xml or context configuration etc Monitoring. If we can get monitoring in the same package, that'll be nice. If not, then yet another tool we can use to monitor our servers. Preferably, open source with tons of documentation ;) Can anyone share their experience? Suggest a few tools? Thanks!

  Read the article

• Autossh startup on Ubuntu 10.04 - fails after powering off

  - by grant

  I'm using upstart to keep a reverse ssh tunnel alive using auto ssh similar to Using Upstart to Manage AutoSSH Reverse Tunnel. This works fine, except after a manual power down I can no longer connect to the machine through the "central server" using the tunnel. I receive "ssh_exchange_identification: Connection closed by remote host". The autossh process is running on the client. I can connect again after re-starting networking. I'm trying to figure out why this is failing consistently after a manual shutdown. Is it possible that I need to do some cleanup on startup that would allow the tunnel to work in this situation, or are there some other debugging/troubleshooting steps I can take to determine the problem? Machine A is the client machine, using autossh. This machine sits behind a firewall and uses the following command in upstart to create an ssh tunnel: /usr/bin/autossh -fN -i /keyfile -o StrictHostKeyChecking=no -R 20098:localhost:22 user@centralserver Machine B we'll call the "central server", which sits in the cloud and is the host. This machine is "centralserver" in the command above. When Machine A is hard powered off, and back on, I cannot connect to it by SSH'ing from my machine (C) to Machine B in the cloud, then using the following command to get to Machine A: ssh -p 2098 user@localhost Again, after a reboot of the client (A), this works fine. It is only after a hard power down that the problem occurs. There are autossh processes that are running on the client machine (A) after powering down and back up, but they just don't seem to doing their job.

  Read the article

• Windows xp blinking under score after bios

  - by heyjoe

  so this is for an older pc I have to repair for a friend. The pc has an hdd of about 60 something gb, It uses win xp and let's say 60-70% of the boots it hangs on showing only an underscore bilking line after bios screen, rest of the times it boots fine or the computer shuts down on xp loading screen. Sometimes if you let it alone while the underscore is blinking, it will boot after a while, like a few minutes, some times it won't boot at all even if you give him more time, like one hour. When it boots successfully the pc seems to work fine. I think it's a bad hard disk and i'm about to suggest buying a new one and switching it but I don't have enough experience and i would hate making him buy a new hdd and not solving the problem. anyone has any tips? I know there are other topics about blinking underscores or cursors while xp is booting but the issues about the pc shutting itself down or sometimes booting really freaks me out. Can't format everything and re install until about 10 days from now, cause the dude has some program for his business on this pc and I have to migrate it when the next computer arrives, however he needs to use it until then. so please advise, thx.

  Read the article

• How can I generate filesystem images that are usable on many different virtualization systems?

  - by Mark Longair

  I have written a script that generates a root filesystem image (based on Debian lenny) suitable for User-Mode Linux. (Essentially this script creates a filesystem image, mounts it with a loop device, uses debootstrap to create a lenny install, sets up a static IP for TUN/TAP networking, adds public keys for login by SSH and installs a web application.) These filesystem images work pretty well with UML, but it would be nice to be able to generate similar images that people can use on alternative virtualization software, and I'm not familiar with these options at all. In particular, since the idea is to use this image as a standalone server for testing the web application, it's important that the networking works. I wonder if anyone can suggest what would be involved in customizing such root filesystem images such that they could be used with other virtualization software, such as VMware, Xen or as an Amazon EC2 instance? Two particular concerns are: If such systems don't use a raw filesystem image (e.g. they need headers with metadata or are compressed in some particular way) do there exist tools to convert between the different formats? I assume that in the filesystem, at least /etc/network/interfaces will have to be customized, but are more involved changes likely to be necessary? Many thanks for any suggestions...

  Read the article

• Removed Old Domain Trust. Now Progress (9.1D) can't open DB File

  - by RLH

  My company has an old server, running Progress 9.1D on a Windows 2000 VM, which was used by our company OS (Vantage 6 by Epicor.) Vantage was our primary OS for a very long time. About 2 years ago, we migrated to a larger, corporate OS and we cancelled our service contract with Epicor. Yesterday, we removed an AD trust between the corporate domain and our old AD domain we used in the days of Vantage. After restarting the virtual server, I have been able to start the ProService for 9.1D Windows service, however, I can not get Vantage to start back up. When I run the application, I get the error in the message listed below. Transcript: ** Could not connect to server for database [progress db file], errno 0. (1432) How can I fix this? FYI, I haven't had to work with Progress in years and even then I wouldn't have considered myself a "novice"-- I'm even less knowledgeable than that title would suggest. Vantage had a lot of internal tools and I recall that Epicor support managed to prevent .pf scripts from being executed. If there was a Progress specific patch that needed to be applied, you had to do it within the Vantage software OR they had to remote into the machine to fix this. I may not be able to run a .pf script but I do know that I can log into the console-based server application. (Yes, I can't even recall which utility that was called. It is sad.) It's been a long time and I never had to digg into Progress that much. Please help and feel free to ask questions. If you need more info, I'll update this post.

  Read the article

< Previous Page | 386 387 388 389 390 391 392 393 394 395 396 397  | Next Page >