Search Results

Search found 13075 results on 523 pages for 'bounding box'.

Page 391/523 | < Previous Page | 387 388 389 390 391 392 393 394 395 396 397 398  | Next Page >

• Lenovo Thinkpad X1 Carbon support

  - by Robottinosino

  I am considering selling my Mac to get money towards a Lenovo Thinkpad X1 because what I really want to do is to be running an Ubuntu system all the time. Is this machine completely supported in Ubuntu, with no tiny little feature missing just because I am "going Linux"? Optional user story section, skip to the question below if you don't have time: I have a friend who bought a "works on Ubuntu" system a year ago and has hated the fact ever since: battery lasts less than if he boots in Windows (which he despises) and he ascribes that to "no good OS/harware integration and support for advanced chipset power management features", odd behaviour on suspend/resume/hibernate (says: "when it works 90% of the time and the other 10% it makes you lose your work is as good as broken - 90% is the same as 0% he says), some occasional graphics card glitches he can perfectly well live with and has almost grown affectionate to, and finally, and that is what would make him undo his choice if he could, bad "input device drivers". He says: trackpoint and trackpad just "feel different", "so much better" on Windows and that was impossible to know from the website brochure. That story makes me very doubtful... but I want to abandon this "walled garden" of prison that is my Mac and go Ubuntu all the way, no doubt about that! My dilemma at this time is just: "I don't want to live with those eternal frustrations for sure"! Here's a directly answerable phrasing of my question: Is the Lenovo Thinkpad X1 supported on Ubuntu? Yes/no, which version? Which hardware features are not supported? Provide a list Optionally: sort the list in descending order of frustration from your experience Optionally: mention if there are acceptable workarounds to the "out-of-the-box" condition described in the earlier points and whether this ameliorates frustration at least to "tolerable" levels Comment: the Ubuntu hardware certification page is so not-for-end-users it's unreal. Whoa. What would make it end-user friendly is: Link to "buy here and you'll be just fine, this is the right configuration for you, it'll work as long as you press BUY on that page and don't browse further" Remove mentions of may and might not work. Just tell it straight: press buy here and you will get a working system with the exception of A, B, C (so that I can decide whether the philosophical "freedom pleasure" I get from escaping an Apple world is enough to off-balance the loss, for instance, of Bluetooth capabilities (something that I of course use on my Mac) but "could" lose to use free (as in freedom) software The certification page fails to dispel doubts in me as an end-user. I don't feel "eased into Ubuntu", I feel "partially informed".

  Read the article

• Navigational Flows in Web Forms

  - by Mona Rakibe

  Navigation flows in the Web UI is a common requirement. In 11.1.1.7 we do not have out of the box support for navigational flows but this is surely on our road-map.Until then this simple approach might meet some of the requirements. In this sample we use a trigger control and Web Form rules show navigation flow for Customer, Orders and Line Items. Start by creating  a new Web Form and adding 3 tabs as Customer,Order,Line Items.Add the elements to each tab. Change the visibility for Order and Line Items to false Tab1 : Customer Tab 2 : Order Tab 3 : Line Item N    Notice we have added trigger controls for Next & Back Buttons.        Now write form rules to change the visibility and selection of tabs based on the clicks of trigger You can now navigate through the forms using the trigger control. Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:10%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} a So Solution to this sample can be downloaded from here.

  Read the article

• Nvidia GT218 repository drivers don't work

  - by user1042840

  I upgraded all packages with sudo apt-get upgrade command on my Ubuntu 10.04 box and I have Ubuntu 12.04 3.2.0-29-generic-pae now. I have two monitors and the following GPU: 01:00.0 VGA compatible controller: NVIDIA Corporation GT218 [NVS 300] (rev a2) After upgrading to 12.04, I somehow lost my previous setup with one common workspace stretched across two monitors. When Ubuntu starts only one monitor is on. I can see the message on the active monitor: Not optimum mode. Recommended mode: 1680x1050 60Hz I used Nvidia proprietary drivers on 10.04 but now jockey-text --list shows: xorg:nvidia_current - NVIDIA accelerated graphics driver (Proprietary, Disabled, Not in use) xorg:nvidia_current_updates - NVIDIA accelerated graphics driver (post-release updates) (Proprietary, Enabled, Not in use) When I run sudo nvidia-settings it says You do not appear to be using the NVIDIA X driver. Please edit your X configuration file (just run `nvidia-xconfig` as root), and restart the X server.' I typed nvidia-xconfig and rebooted, but jockey-text --list says the same after the reboot: Not in use. The same with nvidia-current - Enabled but Not in use. I also tried nvidia-173 but I ended up in tty immediately at startup so I removed it. I used to have some problems with Nvidia proprietary drivers on 10.04, I had to put paths to EDID files in /etc/X11/xorg.conf explicitly, but the resolution was as recommended and both monitors were working. If I understand correctly, nouveau drivers are used now by default because the resolution is still quite high, definitely not 800x600, xrandr showed: xrandr: Failed to get size of gamma for output default Screen 0: minimum 320 x 400, current 1600 x 1200, maximum 1600 x 1200 default connected 1600x1200+0+0 0mm x 0mm 1600x1200 66.0* 1280x1024 76.0 1024x768 76.0 800x600 73.0 640x480 73.0 640x400 0.0 320x400 0.0 1680x1050_60.00 (0x4f) 146.2MHz h: width 1680 start 1784 end 1960 total 2240 skew 0 clock 65.3KHz v: height 1050 start 1053 end 1059 total 1089 clock 60.0Hz However, colors seem a bit faded and blurry with nouveau drivers. Mouse cursor is invisible if it's placed inside Firefox window, and only one monitor is working. I like open source and if it's possible I'd prefer to use nouveau drivers but a few things should be fixed. I'm curious why nvidia-current drivers from the repository don't work now. I read it has something to do with the new X11 server in Ubuntu 12.04, is it true? How can I get it back to work?

  Read the article

• Loading another domain's content in a modal iframe - acceptable?

  - by user568458

  Is it okay to load another page in an iframe in a modal pop-up window - in terms of legal and ethical standards around displaying 3rd party content? I remember a few years ago there was controversy and a debate about whether it was okay to load another domain's page content on your domain in a full-width iframe, with your site providing a masthead with controls for favouriting, linking etc (e.g. like StumbleUpon). I seem to recall that the consensus was, that it was okay so long as you were clearly in no way claiming ownership of the 3rd party content or attempting to modify the content and so long as there was a 'go to site' button or equivalent; and that sites could ask you to exclude them, but generally speaking, it's an acceptable practice. How acceptable would it be considered to be to load another site's page within a modal (lightbox-like) popup box (following all the above principles: clear attribution and a prominent button that kills the iframe and gives them the 3rd party original)? My expectation would be that it would follow the same principles, and be acceptable so long as these conditions were met. Note that I'm asking about the likely legitimate responses of the 3rd party sites and possible legal position, not about usability or UX. I'm aware that this should never ever ever ever ever be the standard way external links are loaded, and that 99% of the time linking to external content like this would be terrible for usability. My specific use case is one of those 1% of cases where loading a separate page in this tab actually wouldn't be the expected behaviour of a link: an interactive data visualisation tool that also acts as a 'browser' of external content (science papers underlying the data it navigates). All other links within the interactive will change something while staying on the same page. If the user clicked one of these external links by mistake (as people often do, even when they are clearly, noisily labelled) and then had to back-button back, they would lose their fine-grained position in the interactive tool (jquery bbq hashchanges being not appropriate for all elements of the tool). New window/tab will simply open the target page on the 3rd party domain. Opening a new window/tab would also be an alternative option (and has its own disadvantages) - my question is, whether this is an alternative that could be considered (in terms of acceptable practice around intellectual property etc), irrespective of which option is best for UX: which is something we'll decide the proper way, based on actual UX testing.

  Read the article

• Zenoss Setup for Windows Servers

  - by Jay Fox

  Recently I was saddled with standing up Zenoss for our enterprise.  We're running about 1200 servers, so manually touching each box was not an option.  We use LANDesk for a lot of automated installs and patching - more about that later.The steps below may not necessarily have to be completed in this order - it's just the way I did it.STEP ONE:Setup a standard AD user.  We want to do this so there's minimal security exposure.  Call the account what ever you want "domain/zenoss" for our examples.***********************************************************STEP TWO:Make the following local groups accessible by your zenoss account.Distributed COM UsersPerformance Monitor UsersEvent Log Readers (which doesn't exist on pre-2008 machines)Here's the Powershell script I used to setup access to these local groups:# Created to add Active Directory account to local groups# Must be run from elevated prompt, with permissions on the remote machine(s).# Create txt file should contain the names of the machines that need the account added, one per line.# Script will process machines line by line.foreach($i in (gc c:\tmp\computers.txt)){# Add the user to the first group$objUser=[ADSI]("WinNT://domain/zenoss")$objGroup=[ADSI]("WinNT://$i/Distributed COM Users")$objGroup.PSBase.Invoke("Add",$objUser.PSBase.Path)# Add the user to the second group$objUser=[ADSI]("WinNT://domain/zenoss")$objGroup=[ADSI]("WinNT://$i/Performance Monitor Users")$objGroup.PSBase.Invoke("Add",$objUser.PSBase.Path)# Add the user to the third group - Group doesn't exist on < Server 2008#$objUser=[ADSI]("WinNT://domain/zenoss")#$objGroup=[ADSI]("WinNT://$i/Event Log Readers")#$objGroup.PSBase.Invoke("Add",$objUser.PSBase.Path)}**********************************************************STEP THREE:Setup security on the machines namespace so our domain/zenoss account can access itThe default namespace for zenoss is:  root/cimv2Here's the Powershell script:#Grant account defined below (line 11) access to WMI Namespace#Has to be run as account with permissions on remote machinefunction get-sid{Param ($DSIdentity)$ID = new-object System.Security.Principal.NTAccount($DSIdentity)return $ID.Translate( [System.Security.Principal.SecurityIdentifier] ).toString()}$sid = get-sid "domain\zenoss"$SDDL = "A;;CCWP;;;$sid" $DCOMSDDL = "A;;CCDCRP;;;$sid"$computers = Get-Content "c:\tmp\computers.txt"foreach ($strcomputer in $computers){    $Reg = [WMIClass]"\\$strcomputer\root\default:StdRegProv"    $DCOM = $Reg.GetBinaryValue(2147483650,"software\microsoft\ole","MachineLaunchRestriction").uValue    $security = Get-WmiObject -ComputerName $strcomputer -Namespace root/cimv2 -Class __SystemSecurity    $converter = new-object system.management.ManagementClass Win32_SecurityDescriptorHelper    $binarySD = @($null)    $result = $security.PsBase.InvokeMethod("GetSD",$binarySD)    $outsddl = $converter.BinarySDToSDDL($binarySD[0])    $outDCOMSDDL = $converter.BinarySDToSDDL($DCOM)    $newSDDL = $outsddl.SDDL += "(" + $SDDL + ")"    $newDCOMSDDL = $outDCOMSDDL.SDDL += "(" + $DCOMSDDL + ")"    $WMIbinarySD = $converter.SDDLToBinarySD($newSDDL)    $WMIconvertedPermissions = ,$WMIbinarySD.BinarySD    $DCOMbinarySD = $converter.SDDLToBinarySD($newDCOMSDDL)    $DCOMconvertedPermissions = ,$DCOMbinarySD.BinarySD    $result = $security.PsBase.InvokeMethod("SetSD",$WMIconvertedPermissions)     $result = $Reg.SetBinaryValue(2147483650,"software\microsoft\ole","MachineLaunchRestriction", $DCOMbinarySD.binarySD)}***********************************************************STEP FOUR:Get the SID for our zenoss account.Powershell#Provide AD User get SID$objUser = New-Object System.Security.Principal.NTAccount("domain", "zenoss") $strSID = $objUser.Translate([System.Security.Principal.SecurityIdentifier]) $strSID.Value******************************************************************STEP FIVE:Modify the Service Control Manager to allow access to the zenoss AD account.This command can be run from an elevated command line, or through Powershellsc sdset scmanager "D:(A;;CC;;;AU)(A;;CCLCRPRC;;;IU)(A;;CCLCRPRC;;;SU)(A;;CCLCRPWPRC;;;SY)(A;;KA;;;BA)(A;;CCLCRPRC;;;PUT_YOUR_SID_HERE_FROM STEP_FOUR)S:(AU;FA;KA;;;WD)(AU;OIIOFA;GA;;;WD)"******************************************************************In step two the script plows through a txt file that processes each computer listed on each line.  For the other scripts I ran them on each machine using LANDesk.  You can probably edit those scripts to process a text file as well.That's what got me off the ground monitoring the machines using Zenoss.  Hopefully this is helpful for you.  Watch the line breaks when copy the scripts.

  Read the article

• Resources to Help You Getting Up To Speed on ADF Mobile

  - by Joe Huang

  Hi, everyone: By now, I hope you would have a chance to review the sample applications and try to deploy it.  This is a great way to get started on learning ADF Mobile.  To help you getting started, here is a central list of "steps to get up to speed on ADF Mobile" and related resources that can help you developing your mobile application. Check out the ADF Mobile Landing Page on the Oracle Technology Network. View this introductory video. Read this Data Sheet and FAQ on ADF Mobile. JDeveloper 11.1.2.3 Download. Download the generic version of JDeveloper for installation on Mac. Note that there are workarounds required to install JDeveloper on a Mac. Download ADF Mobile Extension from JDeveloper Update Center or Here. Please note you will need to configure JDeveloper for Internet access (In HTTP Proxy preferences) in order the install the extension, as the installation process will prompt you for a license that's linked off Oracle's web site. View this end-to-end application creation video. View this end-to-end iOS deployment video if you are developing for iOS devices. Configure your development environment, including location of the SDK, etc in JDeveloper-Tools-Preferences-ADF Mobile dialog box.  The two videos above should cover some of these configuration steps. Check out the sample applications shipped with JDeveloper, and then deploy them to simulator/devices using the steps outlined in the video above.  This blog entry outlines all sample applications shipped with JDeveloper. Develop a simple mobile application by following this tutorial. Try out the Oracle Open World 2012 Hands on Lab to get a sense of how to programmatically access server data.  You will need these source files. Ask questions in the ADF/JDeveloper Forum. Search ADF Mobile Preview Forum for entries from ADF Mobile Beta Testing participants. For all other questions, check out this exhaustive and detailed ADF Mobile Developer Guide. If something does not seem right, check out the ADF Mobile Release Note. Thanks, Oracle ADF Mobile Product Management Team

  Read the article

• Got Samba, Got PyNeighbourhood but still no connection. What else do I need?

  - by Frank A

  I am sure I had already hit post before but then could only find it by backing through browser. Was it deleted? is the question too dumb, sorry that I do not know the right jargon just trying to get answers to my problem anyway have reworded stuff a bit This seems to be a number one requirement for lots of people and 2 months on from setting up my Ubuntu pc, I am still unable to get a lasting connection in either direction. Adding a windows pc to a network is so easy... just a few clicks and get on with using it all. Using all command approaches and modifying configuration files is hardly user friendly. Googling brings up thousands of solutions but mostly they are too techy or assume the user is fully aware of how to use Linux. I do realise that their must be a lot of flavours for connecting to networks. So far I have installed Samba and fiddled with its config file. The day I did all that it worked from XP to Ubuntu. When I came back two days later to transfer my data over it would not connect. Although the the share does show up in Windows (XP) My Network Places. Today I installed PyNeighbourhood and this shows the Ubuntu box and all of the shares I had created at some point on Ubuntu and it even shows this under the XP workgroup name. But instructions on setting the connection up seem to relate to an earlier version and nothing seems to work there either. (I unshared most of those test folders but they still show up her but that is another question. When I click on mount- I can only click on one on the Ubuntu machine, there is one with no name so I assume this to be my attempt to add one XP Shared drive using ipaddress, I get errors. (gksu:9767): Gtk-WARNING **: Unable to locate theme engine in module_path: "pixmap", (gksu:9767): Gtk-WARNING **: Unable to locate theme engine in module_path: "pixmap", (gksu:9767): Gtk-WARNING **: Unable to locate theme engine in module_path: "pixmap", (gksu:9767): Gtk-WARNING **: Unable to locate theme engine in module_path: "pixmap", mount error(6): No such device or address Refer to the mount.cifs(8) manual page (e.g. man mount.cifs) OK tried to find the manual referred to... only an old comment that manual would be produced for future versions. I saw in another thread that Winbind is needed as well or at least I assume as well? Totally lost again? Please help, what else needs to be installed to connect to win pcs on the network.

  Read the article

• How to make an object move again after being stopped by collision in Unity?

  - by Matthew Underwood

  I have a player object which position is always centered on the main camera's viewport. This object has a Rigidbody 2D, a box and circle collider. The player moves around a level, the level has a polygon collider attached. I move the camera until the object hits against the collider, which stops the movement of the camera by setting its speed to 0. The problem happens when I want to move the camera / player object away from the collider. As the speed is already at 0, it cannot move away from the collider. The script attached to the player object, checks for collisions and applies the speed to 0 on the main camera's test script. using UnityEngine; using System.Collections; public class move : MonoBehaviour { public float speed; public test testing; // Use this for initialization void Start () { speed = 10F; testing = Camera.main.GetComponent<test>(); } // Update is called once per frame void FixedUpdate () { Vector3 p = Camera.main.ViewportToWorldPoint(new Vector3(0.5F, 0.5F, Camera.main.nearClipPlane)); transform.position = new Vector3(p.x, p.y, -1); } void OnCollisionEnter2D(Collision2D col) { testing.speed = 0; } void OnCollisionExit2D(Collision2D col) { testing.speed = 10F; } } This is the script attached to the main camera; just a simple script that changes the camera's position. using UnityEngine; using System.Collections; public class test : MonoBehaviour { public float speed; public float translationY; public float translationX; // Use this for initialization void Start () { speed = 10F; } void FixedUpdate () { translationY = Input.GetAxis("Vertical") * speed * Time.deltaTime; translationX = Input.GetAxis("Horizontal") * speed * Time.deltaTime; transform.Translate(translationX, translationY, 0); } } The player object isn't kinematic and is a fixed angle, the colliders aren't triggers and the polygon collider isn't a trigger either. The player is the red square, the collider is the pink area. -- EDIT -- From the latest change the collider set up for the player So if the X speed was disabled. It wouldnt move into the side of the polygon colider which is good, but yet you couldnt move away from it. And moving down would move inside the colider.

  Read the article

• Enabling Attachments in Oracle Forms

  - by Manoj Madhusoodanan

  In this blog I will demonstrate how we can enable attachments in Oracle Form. The user ask is to capture a job description which will be along text. Oracle Apps has a feature called attachments, through some easy setup we can enable attachments in forms. We will be going to addresscustomer ask through this feature. Step 1 : Identify Form Name First thing you have to do is to identify the form to enable attachment. In this scenario form will be PERWSDJT ( Job form in HRMS ). Step 2 :  Identify Document Entity exists or not. If exists then do nothing otherwise create new. Step 3 : Create Document Categories. Here I will create a category Job Description with Default Data Type Long Text and Application Human Resources.Onceit is done I will assign this to Create Job form. Step: 3 Query Attachment Functions for PERWSDJT. Click on Categories and add Job Description.Make sure enabled check box is checked. v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Normal 0 false false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Step 4 : Turn off HR:Use Standard Attachments profile option. Output Go to Work Structures > Job > Description

  Read the article

• Java Cloud Service for developers

  - by JuergenKress

  The advent of cloud computing has reinvented application development for many companies. “That’s the beauty of the cloud,” says Cameron Purdy, vice president of development, Oracle. “It dramatically improves developer productivity because they can do what they do best without having to manage complex development, testing, staging, and production environments.” The key is to find a platform that doesn’t impose proprietary restrictions or force developers to learn new tools. For example, Oracle Java Cloud Service is an enterprise-grade platform as a service for building and deploying Java EE, Oracle WebLogic Server, and Oracle Application Development Framework (Oracle ADF) applications. “It’s designed to be flexible and easy to use,” says Purdy. “And it is also a standards-based solution -it’s not proprietary and there is no cloud lock-in. Developers get instant access to an enterprise-grade environment for a simple, monthly subscription.” Oracle Java Cloud Service instances are created with just a few clicks, so businesses can create a rich application development environment within minutes. Running on Oracle WebLogic Server and Oracle Exalogic, the underlying infrastructure also leverages Oracle Fusion Middleware’s integration with common services. For example, instances come integrated and preconfigured with optimized Oracle Database and Oracle Identity Management configurations. Based on Oracle Enterprise Manager, the Oracle Java Cloud Service console lets customers easily manage and monitor their Oracle Java Cloud Service instances. The open nature of the Oracle Java Cloud Service lets developers integrate through Web services such as SOAP and REST APIs, as well as use their favorite developer tools, whether they are out-of-the-box tools such as Maven and Ant or the productivity features built into Oracle JDeveloper, Oracle Enterprise Pack for Eclipse, or NetBeans IDE. The service allows for the seamless movement of applications between on-premise Oracle WebLogic Server domains and instances of Oracle Java Cloud Service within Oracle Cloud. This approach allows flexibility to mix and match the use of on-premise environments with cloud instances for development, test, and production environments. Visit to learn more and watch videos about Oracle Java Cloud Service. WebLogic Partner Community For regular information become a member in the WebLogic Partner Community please visit: http://www.oracle.com/partners/goto/wls-emea ( OPN account required). If you need support with your account please contact the Oracle Partner Business Center. BlogTwitterLinkedInMixForumWiki Technorati Tags: java,cloud,oracle cloud,java cloud,WebLogic Community,Oracle,OPN,Jürgen Kress

  Read the article

• New Features Of WordPress 3.3 You Must Know

  - by Gopinath

  After months of beta testing, WordPress 3.3 version is going to be released at the end of this month. There are several new features packed in the new version and few of them are going to excite WordPress admins. In this post we are going to discuss about the exciting new features. 1. Drag and Drop Media Uploads One of the biggest improvements in this version of WordPress is it’s all new media uploader. Now you can upload multiple files by just dragging & dropping, instantly resize  the images and filter files by their type. The media upload sports a brand new look WordPress adopted the Pupload plugin to power its media uploader component and it’s written by the same team who created the popular TinyMCE editor plugin. 2. Improved Admin Bar(Toolbar) The admin bar or newly called toolbar has got handful of makeovers. The not so much used items like Search box and other elements are removed to make sure that the bar is not clumsy. The user menu and the related options are moved to the right like how we see in Google’s user bar. Also there are few changes to the colour of the bar to make it more eye friendly. 3. Fly out Admin Menus All the left side bar menus of WordPress admin are now sports a fly out menu style to save a click. In the previous versions if you want to access a sub menu on the left side bar, you need to first click on the category and then choose the menu item from the expanded list. Now on just mouse over you will see a flyout of menu items. 4. Adaptive Admin – Layout Auto Adjust To Fit Various Devices If you own an iPad or any other so called tablets then you are going to love this feature. The admin site of WordPress has got a lot more friendly with tablets and smartphones. WordPress now auto adjusts layout to fit the device through which you are accessing the admin site.  Accessing admin dashboard on your tablets is going to be more fun. 5. Other Features Now that we have read the most useful 4 features here is a small list of other features that may interest you Nice Tooltips are displayed where ever possible to help the newbies to understand the usage of admin site Responsive Layouts jQuery 1.7 and jQuery UI 1.8.16 are the power horses of WordPress Performance improvements This article titled,New Features Of WordPress 3.3 You Must Know, was originally published at Tech Dreams. Grab our rss feed or fan us on Facebook to get updates from us.

  Read the article

• Does the Ubuntu One sync work?

  - by bisi

  I have been on this for several hours now, trying to get a simple second folder to sync with my (paid) account. I cannot tell you how many times I removed all devices, removed stored passwords, killed all processes of u1, logged out and back in online...and still, the tick in the file browser (Synchronize this folder) is loading and loading and loading. Also, I have logged out, rebooted countless times. And this is after me somehow managing to get the u1 preferences to finally "connect" again. I have also checked the status of your services, and none are close to what I am experiencing. And I have checked the suggested related questions above! So please, just confirm whether it is a problem on my side, or a problem on your side. EDIT: In the mean time, here is what has changed, on top of what is mentioned just above. • My files went from 0MB to 71.9MB, and is still rising. • My first folder of 400.2MB is being filled with the data as I write this. The second folder has the folder sub-structure in place. • Both folders now show in the File Browser that it will be synchronized. I believe that right now, it is all back to normal and working fine, and I guess that's what a good night's sleep can do ;). And we're now only back to the point where synchronizing is slow, but will pick up with the release of Natty (https://wiki.ubuntu.com/UbuntuOne/FAQ/WhyIsItTakingSoLongForMyFilesToSync). But to get to the questions: My about says I use 11.04, Natty Narwhal, but I am quite sure the last distribution I installed was 10.10. Folder A is 400.2MB, and Folder B is 29.5MB I am on a DSL line, behind a regular fritz.box setting. No proxy servers in use, and I did not install any particular firewall features. No physical firewall, just the router (on which I have a TV signal as well), and 2 switches to get to this floor. Status: inactive The ubuntuone-indicator runs the same window as when I click on my name on the top-right corner and select Ubuntu one, or in the Control Center choose Ubuntu one. It wasn't supposed to go further than this was it?

  Read the article

• Dual booting windows 8/ubuntu 12.04.2, Grub doesn't appear and machine never boot in ubuntu

  - by black sensei

  i got a new ACER predator AG3620-UR308 which came with windows 8, so i wanted to run ubuntu 12.04.2 on it as a dual booting. To be honest, i've been doing dual booting for a while now so, i did the right thing. the box came with 2TB HDD. so i made 4 partitions with a raw partition just after the windows installation partition I always do manual installation so even if ubuntu didn't detect windows 8, it was ok for me. So i created swap area and finished the installation etc....Grub was install on the only drive there which is sda. After reboot, grub doesn't even come up.So it always boot in windows 8. I did repeat the installation process twice and yield same result. which is weird because this method always works for me so far.Even the laptop am using to write this post is a dual booting windows 7/ mint nadia installed the same way. Is there anything new in windows 8 that i didn't make provision for? Before starting the installation, all i read about was that , windows 8 should be installed first and ubuntu after. I went ahead and disable secure boot from the BIOS and enabled CSM (don't even know what it means) according to Acer custhelp site . I boot from USB and did fdisk -l bellow is the result: ubuntu@ubuntu:~$ sudo fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x8c361cb5 Device Boot Start End Blocks Id System /dev/sda1 1 3907029167 1953514583+ ee GPT Partition 1 does not start on physical sector boundary. Disk /dev/sdb: 8178 MB, 8178892800 bytes 255 heads, 63 sectors/track, 994 cylinders, total 15974400 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0006a87e Device Boot Start End Blocks Id System /dev/sdb1 * 2048 15972351 7985152 b W95 FAT32 ubuntu@ubuntu:~$ Can anybody shed some light? thank you in advance EDIT Hey, i just did another trial with 13.04 this time and still no luck. bios: secure-boot: disabled enable CSM : always 1-delete previous ubuntu partition and swap area partition.now having free space 2- used usb installer to prepare usb with ubuntu-13.04-desktop-amd64.iso 3- rebooted : liveusb didnt detect windows 8, used something else 4-created partition ext4 for / 5-created partition for swap-area 6- default grub path is /dev/sda and clicked install Acer always boots into windows.

  Read the article

• Dual booting windows 8/ubuntu 12.04. Grub doesn't appear and machine never boot in ubuntu

  - by black sensei

  i got a new ACER predator AG3620-UR308 which came with windows 8, so i wanted to run ubuntu 12.04.2 on it as a dual booting. To be honest, i've been doing dual booting for a while now so, i did the right thing. the box came with 2TB HDD. so i made 4 partitions with a raw partition just after the windows installation partition I always do manual installation so even if ubuntu didn't detect windows 8, it was ok for me. So i created swap area and finished the installation etc....Grub was install on the only drive there which is sda. After reboot, grub doesn't even come up.So it always boot in windows 8. I did repeat the installation process twice and yield same result. which is weird because this method always works for me so far.Even the laptop am using to write this post is a dual booting windows 7/ mint nadia installed the same way. Is there anything new in windows 8 that i didn't make provision for? Before starting the installation, all i read about was that , windows 8 should be installed first and ubuntu after. I went ahead and disable secure boot from the BIOS and enabled CSM (don't even know what it means) according to Acer custhelp site . I boot from USB and did fdisk -l bellow is the result: ubuntu@ubuntu:~$ sudo fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x8c361cb5 Device Boot Start End Blocks Id System /dev/sda1 1 3907029167 1953514583+ ee GPT Partition 1 does not start on physical sector boundary. Disk /dev/sdb: 8178 MB, 8178892800 bytes 255 heads, 63 sectors/track, 994 cylinders, total 15974400 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0006a87e Device Boot Start End Blocks Id System /dev/sdb1 * 2048 15972351 7985152 b W95 FAT32 ubuntu@ubuntu:~$ Can anybody shed some light? thank you in advance

  Read the article

• MySQL Enterprise Monitor 3.0.11 has been released

  - by Andy Bang

  We are pleased to announce that MySQL Enterprise Monitor 3.0.11 is now available for download on the My Oracle Support (MOS) web site. It will also be available via the Oracle Software Delivery Cloud in about 1 week. This is a maintenance release that includes a few new features and fixes a number of bugs. You can find more information on the contents of this release in the change log. You will find binaries for the new release on My Oracle Support. Choose the "Patches & Updates" tab, and then choose the "Product or Family (Advanced Search)" side tab in the "Patch Search" portlet. You will also find the binaries on the Oracle Software Delivery Cloud in approximately 1 week. Choose "MySQL Database" as the Product Pack and you will find the Enterprise Monitor along with other MySQL products. Based on feedback from our customers, MySQL Enterprise Monitor (MEM) 3.0 offers many significant improvements over previous releases. Highlights include: Policy-based automatic scheduling of rules and event handling (including email notifications) make administration of scale-out easier and automatic Enhancements such as automatic discovery of MySQL instances, centralized agent configuration and multi-instance monitoring further improve ease of configuration and management The new cloud and virtualization-friendly, "agent-less" design allows remote monitoring of MySQL databases without the need for any remote agents Trends, projections and forecasting - Graphs and Event handlers inform you in advance of impending file system capacity problems Zero Configuration Query Analyzer - Works "out of the box" with MySQL 5.6 Performance_Schema (supported by 5.6.14 or later) False positives from flapping or spikes are avoided using exponential moving averages and other statistical techniques Advisors can analyze data across an entire group; for example, the Replication Configuration Advisor can scan an entire topology to find common configuration errors like duplicate server UUIDs or a slave whose version is less than its master's More information on the contents of this release is available here: What's new in MySQL Enterprise Monitor 3.0? MySQL Enterprise Edition: Demos MySQL Enterprise Monitor Frequently Asked Questions MySQL Enterprise Monitor Change History More information on MySQL Enterprise and the Enterprise Monitor can be found here: http://www.mysql.com/products/enterprise/ http://www.mysql.com/products/enterprise/monitor.html http://www.mysql.com/products/enterprise/query.html http://forums.mysql.com/list.php?142 If you are not a MySQL Enterprise customer and want to try the Monitor and Query Analyzer using our 30-day free customer trial, go to http://www.mysql.com/trials, or contact Sales at http://www.mysql.com/about/contact. If you haven't looked at MEM recently, and especially MEM 3.0, please do so now and let us know what you think. Thanks and Happy Monitoring! - The MySQL Enterprise Tools Development Team

  Read the article

• Multi subnet in ubuntu with dnsmasq

  - by Fox Mulder

  I have a multi lan port box that install ubuntu server 11.10. I am setup network in /etc/network/interfaces file as follow: auto lo iface lo inet loopback auto eth0 iface eth0 inet static      address 192.168.128.254      netmask 255.255.255.0      network 192.168.128.0      broadcast 192.168.128.255      gateway 192.168.128.1      dns-nameservers xxxxxx auto eth1 iface eth1 inet static      address 192.168.11.1      netmask 255.255.255.0      network 192.168.11.0      broadcast 192.168.11.255 auto eth2 iface eth2 inet static      address 192.168.21.1      netmask 255.255.255.0      network 192.168.21.0      broadcast 192.168.21.255 auto eth3 iface eth3 inet static      address 192.168.31.1      netmask 255.255.255.0      network 192.168.31.0      broadcast 192.168.31.255 I am also enable the ip forward by echo 1 /proc/sys/net/ipv4/if_forward in rc.local. my dnsmasq config as follow except-interface=eth0 dhcp-range=interface:eth1,set:wifi,192.168.11.101,192.168.11.200,255.255.255.0 dhcp-range=interface:eth2,set:kids,192.168.21.101,192.168.21.200,255.255.255.0 dhcp-range=interface:eth3,set:game,192.168.31.101,192.168.31.200,255.255.255.0 the dhcp was working fine in eth1,eth2,eth3, any machine plug in the subnet can get correct subnet's ip. My problem was, each subnet machine can't ping each other. for example. 192.168.11.101 can't ping 192.168.21.101 but can ping 192.168.128.1 192.168.31.101 can't ping 192.168.21.101 but can ping 192.168.128.1 I am also try to using route add -net 192.168.11.0 netmask 255.255.255.0 gw 192.168.11.1 (and also 192.168.21.0/192.168.31.0) at this multi-lan-port machine. But still won't work. Does anyone can help ? Thanks.

  Read the article

• Why my collision detection is not accurate?

  - by optimisez

  After trying and trying, I still cannot understand why the leg of character exceeds the wall but no clipping issue when I hit the wall from below. How should I fix it to make him standstill on the wall? void initPlayer() { // Create texture. hr = D3DXCreateTextureFromFileEx(d3dDevice, "player.png", 169, 44, D3DX_DEFAULT, NULL, D3DFMT_A8R8G8B8, D3DPOOL_MANAGED, D3DX_DEFAULT, D3DX_DEFAULT, D3DCOLOR_XRGB(255, 255, 255), NULL, NULL, &player); playerRect.left = playerRect.top = 0; playerRect.right = 29; playerRect.bottom = 36; playerDest.X = 0; playerDest.Y = 564; playerDest.length = playerRect.right - playerRect.left; playerDest.height = playerRect.bottom - playerRect.top; } void initBox() { hr = D3DXCreateTextureFromFileEx(d3dDevice, "brock.png", 330, 132, D3DX_DEFAULT, NULL, D3DFMT_A8R8G8B8, D3DPOOL_MANAGED, D3DX_DEFAULT, D3DX_DEFAULT, D3DCOLOR_XRGB(255, 255, 255), NULL, NULL, &box); boxRect.left = 33; boxRect.top = 0; boxRect.right = 63; boxRect.bottom = 30; boxDest.X = boxDest.Y = 300; boxDest.length = boxRect.right - boxRect.left; boxDest.height = boxRect.bottom - boxRect.top; } bool spriteCollide(Entity player, Entity target) { float left1, left2; float right1, right2; float top1, top2; float bottom1, bottom2; left1 = player.X; left2 = target.X; right1 = player.X + player.length; right2 = target.X + target.length; top1 = player.Y; top2 = target.Y; bottom1 = player.Y + player.height; bottom2 = target.Y + target.height; if (bottom1 < top2) return false; if (top1 > bottom2) return false; if (right1 < left2) return false; if (left1 > right2) return false; return true; } void collideWithBox() { if ( spriteCollide(playerDest, boxDest) && keyArr[VK_UP]) //playerDest.Y += 50; playerDest.Y = boxDest.Y + boxDest.height; else if ( spriteCollide(playerDest, boxDest) && !keyArr[VK_UP]) playerDest.Y = boxDest.Y - boxDest.height; }

  Read the article

• How do you conquer the challenge of designing for large screen real-estate?

  - by Berin Loritsch

  This question is a bit more subjective, but I'm hoping to get some new perspective. I'm so used to designing for a certain screen size (typically 1024x768) that I find that size to not be a problem. Expanding the size to 1280x1024 doesn't buy you enough screen real estate to make an appreciable difference, but will give me a little more breathing room. Basically, I just expand my "grid size" and the same basic design for the slightly smaller screen still works. However, in the last couple of projects my clients were all using 1080p (1920x1080) screens and they wanted solutions to use as much of that real estate as possible. 1920 pixels across provides just under twice the width I am used to, and the wide screen makes some of my old go to design approaches not to work as well. The problem I'm running into is that when presented with so much space, I'm confronted with some major problems. How many columns should I use? The wide format lends itself to a 3 column split with a 2:1:1 split (i.e. the content column bigger than the other two). However, if I go with three columns what do I do with that extra column? How do I make efficient use of the screen real estate? There's a temptation to put everything on the screen at once, but too much information actually makes the application harder to use. White space is important to help make sense of complex information, but too much makes related concepts look too separate. I'm usually working with web applications that have complex data, and visualization and presentation is key to making sense of the raw data. When your user also has a large screen (at least 24"), some information is out of eye sight and you need to move the pointer a long distance. How do you make sure everything that's needed stays within the visual hot points? Simple sites like blogs actually do better when the width is constrained, which results in a lot of wasted real estate. I kind of wonder if having the text box and the text preview side by side would be a big benefit for the admin side of that type of screen? (1:1 two column split). For your answers, I know almost everything in design is "it depends". What I'm looking for is: General principles you use How your approach to design has changed I'm finding that i have to retrain myself how to work with this different format. Every bump in resolution I've worked through to date has been about 25%: 640 to 800 (25% increase), 800 to 1024 (28% increase), and 1024 to 1280 (25% increase). However, the jump from 1280 to 1920 is a good 50% increase in space--the equivalent from jumping from 640 straight to 1024. There was no commonly used middle size to help learn lessons more gradually.

  Read the article

• Why can't Ubuntu find an ext3 filesystem on my hard-drive?

  - by urig

  This question is related to this question: Not enough components to start the RAID array? I'm trying to retrieve data from a "Western Digital MyBook World Edition (white light)" NAS device. This is basically an embedded Linux box with a 1TB HDD in it formatted in ext3. It stopped booting one day for no apparent reason. I have extracted the HDD from the NAS device and installed it in a desktop machine running Ubuntu 10.10 in the hope of accessing the files on the drive. I have followed instructions in this forum post, intended to mount the drive through Terminal: http://mybookworld.wikidot.com/forum/t-90514/how-to-recover-data-from-wd-my-book-world-edition-nas-device#post-976452 I have identified the partition that I want to mount and recover files from as /dev/sd4 by running "fdisk -l" and getting this: Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0001cf00 Device Boot Start End Blocks Id System /dev/sdb1 5 248 1959930 fd Linux raid autodetect /dev/sdb2 249 280 257040 fd Linux raid autodetect /dev/sdb3 281 403 987997+ fd Linux raid autodetect /dev/sdb4 404 121601 973522935 fd Linux raid autodetect// When I try to mount using: "mount -t ext3 /dev/sdb4 /media/xyz" I get the following error: mount: wrong fs type, bad option, bad superblock on /dev/sdb4, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so And "dmesg | tail" shows me: [ 15.184757] [drm] Initialized nouveau 0.0.16 20090420 for 0000:01:00.0 on minor 0 [ 15.986859] [drm] nouveau 0000:01:00.0: Allocating FIFO number 1 [ 15.988379] [drm] nouveau 0000:01:00.0: nouveau_channel_alloc: initialised FIFO 1 [ 16.353379] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro,commit=0 [ 16.705944] tg3 0000:02:00.0: eth0: Link is up at 100 Mbps, full duplex [ 16.705951] tg3 0000:02:00.0: eth0: Flow control is off for TX and off for RX [ 16.706102] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 19.125673] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro,commit=0 [ 27.600012] eth0: no IPv6 routers present [ 373.478031] EXT3-fs (sdb4): error: can't find ext3 filesystem on dev sdb4. I guess that last line is the punch line :) Why can't it find the ext3 filesystem on my drive? What do I need to do to mount this partition and copy its contents? Does it have anything to do with the drive being part of a RAID Array (see question mentioned above)? Many thanks to any who can help.

  Read the article

• Showing ZFS some LOVE

  - by Kristin Rose

  Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} L is for the way you look at us, and O because we’re Oracle, but V is very, very, extra ordinary, and E, well that’s obvious… E is because Oracle’s new Sun ZFS Storage Appliance is Excellent, and here at OPN, we like spell out the obvious!  If you haven’t already heard, the Sun ZFS Appliance has “A simple, GUI-driven setup and configuration, solid price-performance and world-class Oracle support behind it. The CRN Test Center recommends the Sun ZFS Storage”. Read more about what CRN said here. Oracle's Sun ZFS Appliance family delivers enterprise-class network attached storage (NAS) capabilities with leading Oracle integration, simplicity, efficiency, performance, and TCO.  The systems offer an easy way to manage and expand your storage environment at a lower cost, with more efficiency, better data integrity, and higher performance when compared with competitive NAS offerings. Did we mention that set up, including configuring, will take you less than an hour since it all comes in one box and is so darn simple to use? So if you L-O-V-E what you’re hearing about Oracle’s Sun Z-F-S, learn more by watching the video below, and visiting any of our available resources . It Had to Be You, The OPN Communications Team

  Read the article

• ClearTrace Performance on 170GB of Trace Files

  - by Bill Graziano

  I’ve always worked to make ClearTrace perform well.  That’s probably because I spend so much time watching it work.  I’m often going through two or three gigabytes of trace files but I rarely get the chance to run it on a really large set of files. One of my clients wanted to run a full trace for a week and then analyze the results.  At the end of that week we had 847 200MB trace files for a total of nearly 170GB. I regularly use 200MB trace files when I monitor production systems.  I usually get around 300,000 statements in a file that size if it’s mostly stored procedures.  So those 847 trace files contained roughly 250 million statements.  (That’s 730 bytes per statement if you’re keeping track.  Newer trace files have some compression in them but I’m not exactly sure what they’re doing.)  On a system running 1,000 statements per second I get a new file every five minutes or so. It took 27 hours to process these files on an older development box.  That works out to 1.77MB/second.  That means ClearTrace processed about 2,654 statements per second. You can query the data while you’re loading it but I’ve found it works better to use a second instance of ClearTrace to do this.  I’m not sure why yet but I think there’s still some dependency between the two processes. ClearTrace is almost always CPU bound.  It’s really just a huge, ugly collection of regular expressions.  It only writes a summary to its database at the end of each trace file so that usually isn’t a bottleneck.  At the end of this process, the executable was using roughly 435MB of RAM.  Certainly more than when it started but I think that’s acceptable. The database where all this is stored started out at 100MB.  After processing 170GB of trace files the database had grown to 203MB.  The space savings are due to the “datawarehouse-ish” design and only storing a summary of each trace file. You can download ClearTrace for SQL Server 2008 or test out the beta version for SQL Server 2012.  Happy Tuning!

  Read the article

• Ubuntu 12.4.1 failing in vm both Vbox and Vmware on new HP Envy 4t-1000

  - by Chas

  Brand new to Linux, getting frustrated trying to get an environment up with Ubuntu. My primary goal is to learn Linux and Apache/PHP development. I need to keep my Windows OS as main on my machine for work, so i'm trying to virtualize Ubuntu 12.4.1 without luck (many attempts). I have a new HP Envy 4t-1000 with 16gb ram, and 32 gb ssd caching with 500gb spindle hard drive. Graphics card is an Intel HD 3000 with AMD Radeon 7670M. With installing Ubuntu desktop in VBox, I'm getting this result: https://forums.virtualbox.org/viewtopic.php?f=6&t=51939 With VMware workstation 7 (patched), I complete the install of Ubuntu, it reboots, purple desktop briefly flashes then it drops to command line. I bought a beginning Ubuntu book, and it recommends trying to manually configure graphics if this happens. So I tried doing a safe boot holding shift - I get to the first screen (GRUB) loads fine, and I choose recovery mode. After choosing the recovery mode, I get the recovery mode options, and can arrow down to what the book suggests 'Run in fail safe graphic mode.' Once I select this option, I get a black screen with a large white dialogue box, at the top it says "The system is running in low-graphics mode. Your screen, graphics card, and input device settings could not be detected correctly. You will need to configure these yourself." Then there is an ok button way down at the bottom. When I select 'ok' I get a menu for a few options, book recommended 'reconfigure graphics.' When I try this, I get a menu of two options: 1) "Use generic (default) configuration or 2) use backup. I've tried both options several times, hitting ok just refreshes screen and nothing more. Rebooting at this point just goes back to command line as before. I don't know what to do at this point, I've spent too many hours this weekend trying in both VBox and VMware to get Ubuntu going. Isn't there like a very basic graphic display or something I can use to at least get into the desktop? I explored the GRUB some more, and tried to look at the startup and xserver logs - both are blank. No help there I guess? When I try to choose 'Edit the configuration file, then 'ok' screen just refreshes on same menu options, nothing happens. thx for any advice. I really need to focus on learning Linux, Apache and PHP, so perhaps Ubuntu just won't work on my hardware? Any other suggestions? I will need to virtualize - THANKS for any help/advice.

  Read the article

• RadioButtons and Lambda Expressions

  - by MightyZot

  Radio buttons operate in groups. They are used to present mutually exclusive lists of options. Since I started programming in Windows 20 years ago, I have always been frustrated about how they are implemented. To make them operate as a group, you put your radio buttons in a group box. Conversely, to group radio buttons in HTML, you simply give them all the same name. Radio buttons with the same name or ID in HTML operate as one mutually exclusive group of options. In C#, all your radio buttons must have unique names and you use group boxes to group them. I’m in the process of converting some old code to C# and I’m tasked with creating a user control with groups of radio buttons on it. I started out writing the traditional switch…case statements to check the appropriate radio button based upon value, loops to uncheck them all, etc. Then it occurred to me that I could stick the radio buttons in a Dictionary or List and use Lambda expressions to make my code a lot more maintainable. So, here is what I ended up with: Here is a dictionary that contains my list of radio buttons and their values. I used their values as the keys, so that I can select them by value. Now, instead of using loops and switch…case statements to control the radio buttons, I use the lambda syntax and extension methods. Selecting a Radio Button by Value This code is inside of a property accessor, so “value” represents the value passed into the property accessor. The “First” extension method uses the delegate represented by the lambda expression to select the radio button (actually KeyValuePair) that represents the passed in value. Finally, the resulting checkbox is checked. Since the radio buttons are in the same group, they function as a group, the appropriate radio button is selected while the others are unselected. Reading the Value This is the get accessor for the property that returns the value of the checked radio button. Now, if you’re using binding, this code is likely not necessary; however, I didn’t want to use binding in this case, so I think this is a good alternative to the traditional loops and switch…case statements.

  Read the article

• Access to Salesforce.com Data Through Tableau Desktop

  - by dataintegration

  This article will explain how to connect to any of the RSSBus OData Connectors with Tableau's business intelligence tool. While the example uses the Salesforce Connector, the same process can be followed for any of the OData Connectors. Step 1: Download and install both the Salesforce Connector from RSSBus and Tableau Desktop from Tableau. Step 2: Next you will want to configure the Salesforce Connector to connect with your Salesforce.com account. If you browse to the Help tab in the Salesforce Connector application, there is a link to the Getting Started Guide which will walk you through setting up the Salesforce Connector. Step 3: Once you have successfully configured the Salesforce Connector application, you will want to open Tableau and select the Connect to data option at the top left of the window. Step 4: Here you will click on the option labeled OData under the section labeled On a server. Step 5: A new pop up will appear. The box under Step 1 of the pop-up must contain the OData URL of the Salesforce Connector table. You can find this by clicking on the Settings tab of the Salesforce Connector. Once you have found the OData entry URL, you will need to append the table name that you want Tableau to connect with to the OData entry URL. In this example, we will connect to the Account table. Thus, the URL we enter will be: http://localhost:8181/sfconnector/data/conn/odata.rsc/Account. You will also need to add authentication options in this step. To do this, select the Use a Username and Password option in Step 2 of the pop-up and enter the Username and Password of the user who has access to the Salesforce Connector. When you are done, click the Connect button in Step 3 of the pop-up. Step 6: When the connection to the Salesforce Connector is successful, give the connection a name and click the OK button. Step 7: The table columns will be listed on the left side under the Dimensions section of the workspace. Step 8: To view your Salesforce.com data, you can right click under the table name in the Data section at the top left of the dashboard and select the View Data option. Your Saleforce.com data will appear in Tableau.

  Read the article

• MySQL Enterprise Monitor 3.0.3 Is Now Available

  - by Andy Bang

  We are pleased to announce that MySQL Enterprise Monitor 3.0.3 is now available for download on the My Oracle Support (MOS) web site. It will also be available via the Oracle Software Delivery Cloud with the November update in about 1 week. This is a maintenance release that fixes a number of bugs. You can find more information on the contents of this release in the change log. You will find binaries for the new release on My Oracle Support. Choose the "Patches & Updates" tab, and then use the "Product or Family (Advanced Search)" feature. You will also find the binaries on the Oracle Software Delivery Cloud in approximately 1 week. Choose "MySQL Database" as the Product Pack and you will find the Enterprise Monitor along with other MySQL products. Based on feedback from our customers, MySQL Enterprise Monitor (MEM) 3.0 offers many significant improvements over previous releases. Highlights include: Policy-based automatic scheduling of rules and event handling (including email notifications) make administration of scale-out easier and automatic Enhancements such as automatic discovery of MySQL instances, centralized agent configuration and multi-instance monitoring further improve ease of configuration and management The new cloud and virtualization-friendly, "agent-less" design allows remote monitoring of MySQL databases without the need for any remote agents Trends, projections and forecasting - Graphs and Event handlers inform you in advance of impending file system capacity problems Zero Configuration Query Analyzer - Works "out of the box" with MySQL 5.6 Performance_Schema (supported by 5.6.14 or later) False positives from flapping or spikes are avoided using exponential moving averages and other statistical techniques Advisors can analyze data across an entire group; for example, the Replication Configuration Advisor can scan an entire topology to find common configuration errors like duplicate server UUIDs or a slave whose version is less than its master's More information on the contents of this release is available here: What's new in MySQL Enterprise Monitor 3.0? MySQL Enterprise Edition: Demos MySQL Enterprise Monitor Frequently Asked Questions MySQL Enterprise Monitor Change History More information on MySQL Enterprise and the Enterprise Monitor can be found here: http://www.mysql.com/products/enterprise/ http://www.mysql.com/products/enterprise/monitor.html http://www.mysql.com/products/enterprise/query.html http://forums.mysql.com/list.php?142 If you are not a MySQL Enterprise customer and want to try the Monitor and Query Analyzer using our 30-day free customer trial, go to http://www.mysql.com/trials, or contact Sales at http://www.mysql.com/about/contact. If you haven't looked at MEM recently, and especially MEM 3.0, please do so now and let us know what you think. Thanks and Happy Monitoring! - The MySQL Enterprise Tools Development Team

  Read the article

< Previous Page | 387 388 389 390 391 392 393 394 395 396 397 398  | Next Page >