output formats - Page 392

Can't get IPv6 address using radvd on wireless interface on windows, wired works fine.

- by AndrejaKo

I set up my router to use OpenWRT and set it up to use IPv6 using a tunnel form SixXs. I'm having problems with stateless autoconfiguration using radvd. On my computer, wired connection can get its IPv6 address fine, but wireless can't. After spending some time on OpenWRT forums, I'm pretty much sure now that router is set up fine and that the problem is with my windows settings. Also, I do not have any problems getting IPv6 address on openSUSE 11.3. So what should I do to solve this and what information should I post? Here's radvdump output for wired interface: interface br-lan { AdvSendAdvert on; # Note: {Min,Max}RtrAdvInterval cannot be obtained with radvdump AdvManagedFlag on; AdvOtherConfigFlag on; AdvReachableTime 0; AdvRetransTimer 0; AdvCurHopLimit 64; AdvDefaultLifetime 1800; AdvHomeAgentFlag off; AdvDefaultPreference medium; AdvSourceLLAddress on; prefix 2001:15c0:67d0::/64 { AdvValidLifetime 86400; AdvPreferredLifetime 14400; AdvOnLink on; AdvAutonomous on; AdvRouterAddr off; }; # End of prefix definition }; # End of interface definition Here's radvdump output for wireless interface: # # radvd configuration generated by radvdump 1.6 # based on Router Advertisement from fe80::a0b7:deff:fef0:5b34 # received by interface br-lan # interface br-lan { AdvSendAdvert on; # Note: {Min,Max}RtrAdvInterval cannot be obtained with radvdump AdvManagedFlag on; AdvOtherConfigFlag on; AdvReachableTime 0; AdvRetransTimer 0; AdvCurHopLimit 64; AdvDefaultLifetime 1800; AdvHomeAgentFlag off; AdvDefaultPreference medium; AdvSourceLLAddress on; prefix 2001:15c0:67d0::/64 { AdvValidLifetime 86400; AdvPreferredLifetime 14400; AdvOnLink on; AdvAutonomous on; AdvRouterAddr off; }; # End of prefix definition }; # End of interface definition # # radvd configuration generated by radvdump 1.6 # based on Router Advertisement from fe80::a0b7:deff:fef0:5b34 # received by interface br-lan # interface br-lan { AdvSendAdvert on; # Note: {Min,Max}RtrAdvInterval cannot be obtained with radvdump AdvManagedFlag on; AdvOtherConfigFlag on; AdvReachableTime 0; AdvRetransTimer 0; AdvCurHopLimit 64; AdvDefaultLifetime 1800; AdvHomeAgentFlag off; AdvDefaultPreference medium; AdvSourceLLAddress on; prefix 2001:15c0:67d0::/64 { AdvValidLifetime 86400; AdvPreferredLifetime 14400; AdvOnLink on; AdvAutonomous on; AdvRouterAddr off; }; # End of prefix definition }; # End of interface definition

Read the article

linux raid 1: right after replacing and syncing one drive, the other disk fails - understanding what is going on with mdstat/mdadm

- by devicerandom

We have an old RAID 1 Linux server (Ubuntu Lucid 10.04), with four partitions. A few days ago /dev/sdb failed, and today we noticed /dev/sda had pre-failure ominous SMART signs (~4000 reallocated sector count). We replaced /dev/sdb this morning and rebuilt the RAID on the new drive, following this guide: http://www.howtoforge.com/replacing_hard_disks_in_a_raid1_array Everything went smooth until the very end. When it looked like it was finishing to synchronize the last partition, the other old one failed. At this point I am very unsure of the state of the system. Everything seems working and the files seem to be all accessible, just as if it synchronized everything, but I'm new to RAID and I'm worried about what is going on. The /proc/mdstat output is: Personalities : [raid1] [linear] [multipath] [raid0] [raid6] [raid5] [raid4] [raid10] md3 : active raid1 sdb4[2](S) sda4[0] 478713792 blocks [2/1] [U_] md2 : active raid1 sdb3[1] sda3[2](F) 244140992 blocks [2/1] [_U] md1 : active raid1 sdb2[1] sda2[2](F) 244140992 blocks [2/1] [_U] md0 : active raid1 sdb1[1] sda1[2](F) 9764800 blocks [2/1] [_U] unused devices: <none> The order of [_U] vs [U_]. Why aren't they consistent along all the array? Is the first U /dev/sda or /dev/sdb? (I tried looking on the web for this trivial information but I found no explicit indication) If I read correctly for md0, [_U] should be /dev/sda1 (down) and /dev/sdb1 (up). But if /dev/sda has failed, how can it be the opposite for md3 ? I understand /dev/sdb4 is now spare because probably it failed to synchronize it 100%, but why does it show /dev/sda4 as up? Shouldn't it be [__]? Or [_U] anyway? The /dev/sda drive now cannot even be accessed by SMART anymore apparently, so I wouldn't expect it to be up. What is wrong with my interpretation of the output? I attach also the outputs of mdadm --detail for the four partitions: /dev/md0: Version : 00.90 Creation Time : Fri Jan 21 18:43:07 2011 Raid Level : raid1 Array Size : 9764800 (9.31 GiB 10.00 GB) Used Dev Size : 9764800 (9.31 GiB 10.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:27:33 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : a3b4dbbd:859bf7f2:bde36644:fcef85e2 Events : 0.7704 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 17 1 active sync /dev/sdb1 2 8 1 - faulty spare /dev/sda1 /dev/md1: Version : 00.90 Creation Time : Fri Jan 21 18:43:15 2011 Raid Level : raid1 Array Size : 244140992 (232.83 GiB 250.00 GB) Used Dev Size : 244140992 (232.83 GiB 250.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:39:06 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : 8bcd5765:90dc93d5:cc70849c:224ced45 Events : 0.1508280 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 18 1 active sync /dev/sdb2 2 8 2 - faulty spare /dev/sda2 /dev/md2: Version : 00.90 Creation Time : Fri Jan 21 18:43:19 2011 Raid Level : raid1 Array Size : 244140992 (232.83 GiB 250.00 GB) Used Dev Size : 244140992 (232.83 GiB 250.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:46:44 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : 2885668b:881cafed:b8275ae8:16bc7171 Events : 0.2289636 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 19 1 active sync /dev/sdb3 2 8 3 - faulty spare /dev/sda3 /dev/md3: Version : 00.90 Creation Time : Fri Jan 21 18:43:22 2011 Raid Level : raid1 Array Size : 478713792 (456.54 GiB 490.20 GB) Used Dev Size : 478713792 (456.54 GiB 490.20 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 3 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:19:20 2013 State : clean, degraded Active Devices : 1 Working Devices : 2 Failed Devices : 0 Spare Devices : 1 Number Major Minor RaidDevice State 0 8 4 0 active sync /dev/sda4 1 0 0 1 removed 2 8 20 - spare /dev/sdb4 The active sync on /dev/sda4 baffles me. I am worried because if tomorrow morning I have to replace /dev/sda, I want to be sure what should I sync with what and what is going on. I am also quite baffled by the fact /dev/sda decided to fail exactly when the raid finished resyncing. I'd like to understand what is really happening. Thanks a lot for your patience and help. Massimo

Read the article

Is there a bug with Apache 2.2 and content filters (and maybe mod_proxy)?

- by asciiphil

I'm running Apache 2.2.15-29 on RHEL 6 (actually Scientific Linux 6.4) and I'm trying to set up a reverse proxy with content rewriting so all of the links on the proxied web pages are rewritten to reference the proxy host. I'm running into a problem with some of the content rewriting and I'd like to know if this is a bug or if I'm doing something wrong (and how to do it right, if applicable). I'm proxying a subdirectory on an internal host (internal.example.com/foo) onto the root of an external host (external.example.com). I need to rewrite HTML, CSS, and Javascript content to fix all of the URLs. I'm also hosting some content locally on the external host, which I don't think is a problem but I'm mentioning here for completeness. My httpd.conf looks roughly like this: <VirtualHost *:80> ServerName external.example.com ServerAlias example.com # Serve all local content directly, reverse-proxy all unknown URIs. RewriteEngine On RewriteRule ^(/(index.html?)?)?$ http://internal.example.com/foo/ [P] RewriteCond %{DOCUMENT_ROOT}%{REQUEST_FILENAME} -f [OR] RewriteCond %{DOCUMENT_ROOT}%{REQUEST_FILENAME} -d RewriteRule ^.*$ - [L] RewriteRule ^/~ - [L] RewriteRule ^(.*)$ http://internal.example.com$1 [P] # Standard header rewriting. ProxyPassReverse / http://internal.example.com/foo/ ProxyPassReverseCookieDomain internal.example.com external.example.com ProxyPassReverseCookiePath /foo/ / # Strip any Accept-Encoding: headers from the client so we can process the pages # as plain text. RequestHeader unset Accept-Encoding # Use mod_proxy_html to fix URLs in text/html content. ProxyHTMLEnable On ProxyHTMLURLMap http://internal.example.com/foo/ / ProxyHTMLURLMap http://internal.example.com/foo / ProxyHTMLURLMap /foo/ / ## Use mod_substitute to fix URLs in CSS and Javascript #<Location /> # AddOutputFilterByType SUBSTITUTE text/css # AddOutputFilterByType SUBSTITUTE text/javascript # Substitute "s|http://internal.example.com/foo/|/|nq" #</Location> # Use mod_ext_filter to fix URLs in CSS and Javascript ExtFilterDefine fixurlcss mode=output intype=text/css cmd="/bin/sed -rf /etc/httpd/fixurls" ExtFilterDefine fixurljs mode=output intype=text/javascript cmd="/bin/sed -rf /etc/httpd/fixurls" <Location /> SetOutputFilter fixurlcss;fixurljs </Location> </VirtualHost> The text/html rewriting works just fine. When I use either mod_substitute or mod_ext_filter, the external server sends the pages as Transfer-Encoding: chunked, sends all of the data, and then closes the connection without sending the final, zero-length chunk. Some HTTP clients are unhappy with this. (Chrome won't process any content sent in this way, for example, so the pages don't get CSS applied to them.) Here's a sample wget session: $ wget -O /dev/null -S http://external.example.com/include/jquery.js --2013-11-01 11:36:36-- http://external.example.com/include/jquery.js Resolving external.example.com (external.example.com)... 192.168.0.1 Connecting to external.example.com (external.example.com)|192.168.0.1|:80... connected. HTTP request sent, awaiting response... HTTP/1.1 200 OK Date: Fri, 01 Nov 2013 15:36:36 GMT Server: Apache Last-Modified: Tue, 29 Oct 2013 13:09:10 GMT ETag: "1d60026-187b8-4e9e0ec273e35" Accept-Ranges: bytes Vary: Accept-Encoding X-UA-Compatible: IE=edge,chrome=1 Content-Type: text/javascript;charset=utf-8 Connection: close Transfer-Encoding: chunked Length: unspecified [text/javascript] Saving to: `/dev/null' [ <=> ] 100,280 --.-K/s in 0.005s 2013-11-01 11:36:37 (19.8 MB/s) - Read error at byte 100280 (Success).Retrying. --2013-11-01 11:36:38-- (try: 2) http://external.example.com/include/jquery.js Connecting to external.example.com (external.example.com)|192.168.0.1|:80... connected. HTTP request sent, awaiting response... HTTP/1.1 416 Requested Range Not Satisfiable Date: Fri, 01 Nov 2013 15:36:38 GMT Server: Apache Vary: Accept-Encoding Content-Type: text/html;charset=utf-8 Content-Length: 260 Connection: close The file is already fully retrieved; nothing to do. Am I doing something wrong? Am I hitting some sort of Apache bug? What do I need to do to get it working? (Note that I'd prefer solutions that work within RHEL-6-packaged RPMs and upgrading to Apache 2.4 would be a last resort, as we have a lot of infrastructure built around 2.2 on this system at the moment.)

Read the article

Why am I unable to telnet to a local port that has a listening service?

- by Skip Huffman

I suspect this is either a very simple question, or a very complex one. I have a headless server running ubuntu 10.04 that I can ssh into. I have full root access to the system. I am trying to set up an ssh tunnel to allow me to vnc to the system (but that isn't my question. I have vnc running on port 5903, here is the netstat output for that: Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:5903 0.0.0.0:* LISTEN 7173/Xtightvnc tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 465/sshd But when I try to telnet to that port, from within the same system and login, I get unable to connect errors # telnet localhost 5903 Trying ::1... Trying 127.0.0.1... telnet: Unable to connect to remote host: Connection timed out I am able to telnet to port 22 (as a verification) ~# telnet localhost 22 Trying ::1... Connected to localhost. Escape character is '^]'. SSH-2.0-OpenSSH_5.3p1 Debian-3ubuntu7 I have tried to open up any possible ports using ufw (probably clumsy fashion) # ufw status numbered Status: active To Action From -- ------ ---- [ 1] 5903 ALLOW IN Anywhere [ 2] 22 ALLOW IN Anywhere What else might be blocking this connection locally? Thank you, Edit: The only reference to port 5903 in iptable -L -n is this: Chain ufw-user-input (1 references) target prot opt source destination ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:5903 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:5903 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:22 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:22 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:8080 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:8080 I can post the whole output if that will be useful. hosts.allow and hosts.deny both contain only comments. Re-Edit: Some other questions pointed me to nmap, so I ran a portscan through that utility: # nmap -v -sT localhost -p1-65535 Starting Nmap 5.00 ( http://nmap.org ) at 2011-11-09 09:58 PST NSE: Loaded 0 scripts for scanning. Warning: Hostname localhost resolves to 2 IPs. Using 127.0.0.1. Initiating Connect Scan at 09:58 Scanning localhost (127.0.0.1) [65535 ports] Discovered open port 22/tcp on 127.0.0.1 Connect Scan Timing: About 18.56% done; ETC: 10:01 (0:02:16 remaining) Connect Scan Timing: About 44.35% done; ETC: 10:00 (0:01:17 remaining) Completed Connect Scan at 10:00, 112.36s elapsed (65535 total ports) Host localhost (127.0.0.1) is up (0.00s latency). Interesting ports on localhost (127.0.0.1): Not shown: 65533 filtered ports PORT STATE SERVICE 22/tcp open ssh 80/tcp closed http Read data files from: /usr/share/nmap Nmap done: 1 IP address (1 host up) scanned in 112.43 seconds Raw packets sent: 0 (0B) | Rcvd: 0 (0B) I think this shows that 5903 is blocked somehow. Which I pretty much knew. The question remains what is blocking it and how to modify. Re-re-edit: To check Paul Lathrop's suggested answer, I first verified my ip address with ifconfig: eth0 Link encap:Ethernet HWaddr 02:16:3e:42:28:8f inet addr:10.0.10.3 Bcast:10.0.10.255 Mask:255.255.255.0 Then tried to telnet to 5903 from that address: # telnet 10.0.10.3 5903 Trying 10.0.10.3... telnet: Unable to connect to remote host: Connection timed out No luck. Re-re-re-re-edit: Ok, I think I have isolated it a bit to vncserver, not the firewall, darn it. I shut off vncserver and had netcat listen on port 5903. My vnc client then was able to establish a connnection and sit and wait for a response. Looks like I should be chasing a vnc problem. At least that is progress Thanks for the help

Read the article

how to install 'version.h' in ubuntu ?

- by user252098

Just now , I try to install the Jungo WinDriver in the Ubuntu 13.10 . But I am puzzled by the its manual of how to Install version.h : Install version.h: The file version.h is created when you first compile the Linux kernel source code. Some distributions provide a compiled kernel without the file version.h. Look under /usr/src/linux/include/linux to see whether you have this file. If you do not, follow these steps: Become super user: $ su Change directory to the Linux source directory: # cd /usr/src/linux Type: # make xconfig Save the configuration by choosing Save and Exit. Type: # make dep Exit super user mode: # exit But the shell says: warning: make dep is unnecessary now. Then, I found out there is a version.h in /usr/src/linux-headers-3.11.0.12-generic, so I type: /usr/src/windriver/redist# ./configure --with-kernel-source=/usr/src/linux-headers-3.11.0.12-generic But, the windriver run fails: USE_KBUILD = yes checking for cpu architecture... x86_64 checking for WinDriver root directory... /usr/src/WinDriver checking for linux kernel source... found at /usr/src/linux checking for lib directory... ln -sf $(ROOT_DIR)/lib/$(SHARED_OBJECT)_32.so /usr/lib/$(SHARED_OBJECT).so; ln -s /usr/lib /usr/lib64; ln -sf $(ROOT_DIR)/lib/$(SHARED_OBJECT).so /usr/lib64/$(SHARED_OBJECT).so checking which directories to include... -I/usr/src/linux/include checking linux kernel version... 3.11.10.6 checking for modules installation directory... /lib/modules/3.11.0-12-generic/kernel/drivers/misc checking output directory... LINUX.3.11.0-12-generic.x86_64 checking target... LINUX.3.11.0-12-generic.x86_64/windrvr6_usb.ko checking for regparm kernel option... find: `/usr/src/WinDriver/redist/.tmp_driver/.tmp_versions': No such file or directory 0 checking for modpost location... /usr/src/linux/scripts/mod/modpost configure.usb: creating ./config.status config.status: creating makefile.usb.kbuild checking for cpu architecture... x86_64 checking for WinDriver root directory... /usr/src/WinDriver checking for linux kernel source... found at /usr/src/linux checking for lib directory... ln -sf $(ROOT_DIR)/lib/$(SHARED_OBJECT)_32.so /usr/lib/$(SHARED_OBJECT).so; ln -s /usr/lib /usr/lib64; ln -sf $(ROOT_DIR)/lib/$(SHARED_OBJECT).so /usr/lib64/$(SHARED_OBJECT).so checking which directories to include... -I/usr/src/linux/include checking linux kernel version... 3.11.10.6 checking for modules installation directory... /lib/modules/3.11.0-12-generic/kernel/drivers/misc checking output directory... LINUX.3.11.0-12-generic.x86_64 checking target... LINUX.3.11.0-12-generic.x86_64/windrvr6.ko checking for regparm kernel option... find: `/usr/src/WinDriver/redist/.tmp_driver/.tmp_versions': No such file or directory 0 checking for right linked object... windrvr_gcc_v3.a checking for modpost location... /usr/src/linux/scripts/mod/modpost configure.wd: creating ./config.status config.status: creating makefile.wd.kbuild What is the problem?

Read the article

Unity completely broken after upgrade to 12.10?

- by NlightNFotis

I am facing a very frustrating issue with my computer right now. I successfully upgraded to Ubuntu 12.10 this afternoon, but after the upgrade, the graphical user interface seems completely broken. To be more specific, I can not get the Unity bar to appear on the right. I have tried many things, including (but not limited to) purging and then reinstalling the fglrx drivers, apt-get install --reinstall ubuntu-desktop, apt-get install --reinstall unity, tried to remove the Xorg and Compiz configurations, checked to see if the Ubuntu Unity wall was enabled (it was) in ccsm, all to no avail. Could someone help me troubleshoot and essentially fix this issue? NOTE: This is the output when I try to enable unity via a terminal: compiz (core) - Info: Loading plugin: core compiz (core) - Info: Starting plugin: core unity-panel-service: no process found compiz (core) - Info: Loading plugin: reset compiz (core) - Error: Failed to load plugin: reset compiz (core) - Info: Loading plugin: ccp compiz (core) - Info: Starting plugin: ccp compizconfig - Info: Backend : gsettings compizconfig - Info: Integration : true compizconfig - Info: Profile : unity compiz (core) - Info: Loading plugin: composite compiz (core) - Info: Starting plugin: composite compiz (core) - Info: Loading plugin: opengl X Error of failed request: BadRequest (invalid request code or no such operation) Major opcode of failed request: 153 (GLX) Minor opcode of failed request: 19 (X_GLXQueryServerString) Serial number of failed request: 22 Current serial number in output stream: 22 compiz (core) - Info: Unity is not supported by your hardware. Enabling software rendering instead (slow). compiz (core) - Info: Starting plugin: opengl Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 compiz (core) - Error: Plugin initScreen failed: opengl compiz (core) - Error: Failed to start plugin: opengl compiz (core) - Info: Unloading plugin: opengl compiz (core) - Info: Loading plugin: decor compiz (core) - Info: Starting plugin: decor compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 compiz (core) - Info: Loading plugin: imgpng compiz (core) - Info: Starting plugin: imgpng compiz (core) - Info: Loading plugin: vpswitch compiz (core) - Info: Starting plugin: vpswitch compiz (core) - Info: Loading plugin: resize compiz (core) - Info: Starting plugin: resize Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 compiz (core) - Info: Loading plugin: compiztoolbox compiz (core) - Info: Starting plugin: compiztoolbox compiz (core) - Error: Plugin 'opengl' not loaded. compiz (core) - Info: Loading plugin: move compiz (core) - Info: Starting plugin: move compiz (core) - Info: Loading plugin: gnomecompat compiz (core) - Info: Starting plugin: gnomecompat compiz (core) - Info: Loading plugin: mousepoll compiz (core) - Info: Starting plugin: mousepoll compiz (core) - Info: Loading plugin: wall compiz (core) - Info: Starting plugin: wall compiz (core) - Error: Plugin 'opengl' not loaded. compiz (core) - Error: Plugin init failed: wall compiz (core) - Error: Failed to start plugin: wall compiz (core) - Info: Unloading plugin: wall compiz (core) - Info: Loading plugin: regex compiz (core) - Info: Starting plugin: regex compiz (core) - Info: Loading plugin: snap compiz (core) - Info: Starting plugin: snap compiz (core) - Info: Loading plugin: unitymtgrabhandles compiz (core) - Info: Starting plugin: unitymtgrabhandles compiz (core) - Error: Plugin 'opengl' not loaded. compiz (core) - Error: Plugin init failed: unitymtgrabhandles compiz (core) - Error: Failed to start plugin: unitymtgrabhandles compiz (core) - Info: Unloading plugin: unitymtgrabhandles compiz (core) - Info: Loading plugin: place compiz (core) - Info: Starting plugin: place compiz (core) - Info: Loading plugin: grid compiz (core) - Info: Starting plugin: grid Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 compiz (core) - Info: Loading plugin: animation compiz (core) - Info: Starting plugin: animation compiz (core) - Error: Plugin 'opengl' not loaded. compiz (core) - Error: Plugin init failed: animation compiz (core) - Error: Failed to start plugin: animation compiz (core) - Info: Unloading plugin: animation compiz (core) - Info: Loading plugin: fade compiz (core) - Info: Starting plugin: fade compiz (core) - Error: Plugin 'opengl' not loaded. compiz (core) - Error: Plugin init failed: fade compiz (core) - Error: Failed to start plugin: fade compiz (core) - Info: Unloading plugin: fade compiz (core) - Info: Loading plugin: session compiz (core) - Info: Starting plugin: session compiz (core) - Info: Loading plugin: expo compiz (core) - Info: Starting plugin: expo compiz (core) - Error: Plugin 'opengl' not loaded. compiz (core) - Error: Plugin init failed: expo compiz (core) - Error: Failed to start plugin: expo compiz (core) - Info: Unloading plugin: expo compiz (core) - Info: Loading plugin: ezoom compiz (core) - Info: Starting plugin: ezoom compiz (core) - Error: Plugin 'opengl' not loaded. compiz (core) - Error: Plugin init failed: ezoom compiz (core) - Error: Failed to start plugin: ezoom compiz (core) - Info: Unloading plugin: ezoom compiz (core) - Info: Loading plugin: workarounds compiz (core) - Info: Starting plugin: workarounds compiz (core) - Error: Plugin 'opengl' not loaded. Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 compiz (core) - Info: Loading plugin: scale compiz (core) - Info: Starting plugin: scale compiz (core) - Error: Plugin 'opengl' not loaded. compiz (core) - Error: Plugin init failed: scale compiz (core) - Error: Failed to start plugin: scale compiz (core) - Info: Unloading plugin: scale Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Segmentation fault (core dumped)

Read the article

How to resolve Unmet dependencies error?

- by dandelion

Using my new install of Ubuntu I haven't been able to download anything from the software center except the maryo game without the following error: The following packages have unmet dependencies: vlc: Depends: vlc-nox (= 1.1.12-2~oneiric1) but 1.1.12-2~oneiric1 is to be installed Depends: libaa1 (>= 1.4p5) but 1.4p5-38build1 is to be installed Depends: libavcodec-extra-53 (>= 4:0.7-1) but 4:0.7.3ubuntu0.11.10.1 is to be installed Depends: libavutil-extra-51 (>= 4:0.7-1) but 4:0.7.3ubuntu0.11.10.1 is to be installed Depends: libc6 (>= 2.8) but 2.13-20ubuntu5.1 is to be installed Depends: libfreetype6 (>= 2.2.1) but 2.4.4-2ubuntu1.1 is to be installed Depends: libgcc1 (>= 1:4.1.1) but 1:4.6.1-9ubuntu3 is to be installed Depends: libqtcore4 (>= 4:4.7.0~beta1) but 4:4.7.4-0ubuntu8.1 is to be installed Depends: libqtgui4 (>= 4:4.5.3) but 4:4.7.4-0ubuntu8.1 is to be installed Depends: libsdl-image1.2 (>= 1.2.10) but 1.2.10-2.1 is to be installed Depends: libsdl1.2debian (>= 1.2.10-1) but 1.2.14-6.1ubuntu4 is to be installed Depends: libstdc++6 (>= 4.6) but 4.6.1-9ubuntu3 is to be installed Depends: libva-x11-1 (> 1.0.12~) but it is not going to be installed Depends: libva1 (> 1.0.12~) but it is not going to be installed Depends: libxcb-randr0 (>= 1.1) but it is not going to be installed Depends: libxcb-xv0 (>= 1.2) but it is not going to be installed Depends: zlib1g (>= 1:1.2.3.3.dfsg) but 1:1.2.3.4.dfsg-3ubuntu3 is to be installed My system specs are version 11.10 64 bit. ge-g41m-es2l mother board amd 5770 video card wdc green 500 gig hard drive I have recently changed the motherboard, but otherwise have not changed my computer from when I used to be running the same version of Ubuntu. edit still unable to download output of sudo apt-get update output of sudo apt-get update ~$ sudo apt-get update Ign http://extras.ubuntu.com oneiric InRelease Ign http://security.ubuntu.com oneiric-security InRelease Ign http://archive.canonical.com oneiric InRelease Ign http://ppa.launchpad.net oneiric InRelease Ign http://us.archive.ubuntu.com oneiric InRelease Ign http://us.archive.ubuntu.com oneiric-updates InRelease Ign http://us.archive.ubuntu.com oneiric-backports InRelease Hit http://extras.ubuntu.com oneiric Release.gpg Hit http://archive.canonical.com oneiric Release.gpg Hit http://security.ubuntu.com oneiric-security Release.gpg Hit http://ppa.launchpad.net oneiric Release.gpg Ign http://us.archive.ubuntu.com oneiric-proposed InRelease Hit http://us.archive.ubuntu.com oneiric Release.gpg Hit http://extras.ubuntu.com oneiric Release Hit http://archive.canonical.com oneiric Release Hit http://security.ubuntu.com oneiric-security Release Hit http://ppa.launchpad.net oneiric Release Hit http://us.archive.ubuntu.com oneiric-updates Release.gpg Hit http://us.archive.ubuntu.com oneiric-backports Release.gpg Hit http://extras.ubuntu.com oneiric/main Sources Hit http://archive.canonical.com oneiric/partner i386 Packages Hit http://security.ubuntu.com oneiric-security/main Sources Hit http://ppa.launchpad.net oneiric/main Sources Hit http://us.archive.ubuntu.com oneiric-proposed Release.gpg Hit http://extras.ubuntu.com oneiric/main i386 Packages Ign http://extras.ubuntu.com oneiric/main TranslationIndex Hit http://ppa.launchpad.net oneiric/main i386 Packages Ign http://ppa.launchpad.net oneiric/main TranslationIndex Ign http://archive.canonical.com oneiric/partner TranslationIndex Hit http://security.ubuntu.com oneiric-security/restricted Sources Hit http://security.ubuntu.com oneiric-security/universe Sources Hit http://security.ubuntu.com oneiric-security/multiverse Sources Hit http://security.ubuntu.com oneiric-security/main i386 Packages Hit http://security.ubuntu.com oneiric-security/restricted i386 Packages Hit http://us.archive.ubuntu.com oneiric Release Hit http://us.archive.ubuntu.com oneiric-updates Release Hit http://security.ubuntu.com oneiric-security/universe i386 Packages Hit http://security.ubuntu.com oneiric-security/multiverse i386 Packages Hit http://security.ubuntu.com oneiric-security/main TranslationIndex Hit http://security.ubuntu.com oneiric-security/multiverse TranslationIndex Hit http://security.ubuntu.com oneiric-security/restricted TranslationIndex Hit http://security.ubuntu.com oneiric-security/universe TranslationIndex Hit http://us.archive.ubuntu.com oneiric-backports Release Hit http://security.ubuntu.com oneiric-security/main Translation-en Hit http://security.ubuntu.com oneiric-security/multiverse Translation-en Hit http://us.archive.ubuntu.com oneiric-proposed Release Hit http://us.archive.ubuntu.com oneiric/main Sources Hit http://us.archive.ubuntu.com oneiric/restricted Sources Hit http://us.archive.ubuntu.com oneiric/universe Sources Hit http://us.archive.ubuntu.com oneiric/multiverse Sources Hit http://security.ubuntu.com oneiric-security/restricted Translation-en Hit http://us.archive.ubuntu.com oneiric/restricted i386 Packages Hit http://us.archive.ubuntu.com oneiric/universe i386 Packages Hit http://us.archive.ubuntu.com oneiric/multiverse i386 Packages Hit http://us.archive.ubuntu.com oneiric/main TranslationIndex Hit http://us.archive.ubuntu.com oneiric/multiverse TranslationIndex Hit http://us.archive.ubuntu.com oneiric/restricted TranslationIndex Hit http://us.archive.ubuntu.com oneiric/universe TranslationIndex Hit http://us.archive.ubuntu.com oneiric-updates/main Sources Hit http://us.archive.ubuntu.com oneiric-updates/restricted Sources Hit http://security.ubuntu.com oneiric-security/universe Translation-en Hit http://us.archive.ubuntu.com oneiric-updates/universe Sources Hit http://us.archive.ubuntu.com oneiric-updates/multiverse Sources Hit http://us.archive.ubuntu.com oneiric-updates/main i386 Packages Hit http://us.archive.ubuntu.com oneiric-updates/restricted i386 Packages Hit http://us.archive.ubuntu.com oneiric-updates/universe i386 Packages Hit http://us.archive.ubuntu.com oneiric-updates/multiverse i386 Packages Hit http://us.archive.ubuntu.com oneiric-updates/main TranslationIndex Hit http://us.archive.ubuntu.com oneiric-updates/multiverse TranslationIndex Hit http://us.archive.ubuntu.com oneiric-updates/restricted TranslationIndex Hit http://us.archive.ubuntu.com oneiric-updates/universe TranslationIndex Hit http://us.archive.ubuntu.com oneiric-backports/main Sources Hit http://us.archive.ubuntu.com oneiric-backports/restricted Sources Hit http://us.archive.ubuntu.com oneiric-backports/universe Sources Hit http://us.archive.ubuntu.com oneiric-backports/multiverse Sources Hit http://us.archive.ubuntu.com oneiric-backports/main i386 Packages Hit http://us.archive.ubuntu.com oneiric-backports/restricted i386 Packages Hit http://us.archive.ubuntu.com oneiric-backports/universe i386 Packages Hit http://us.archive.ubuntu.com oneiric-backports/multiverse i386 Packages Hit http://us.archive.ubuntu.com oneiric-backports/main TranslationIndex Hit http://us.archive.ubuntu.com oneiric-backports/multiverse TranslationIndex Hit http://us.archive.ubuntu.com oneiric-backports/restricted TranslationIndex Hit http://us.archive.ubuntu.com oneiric-backports/universe TranslationIndex Ign http://extras.ubuntu.com oneiric/main Translation-en_US Ign http://ppa.launchpad.net oneiric/main Translation-en_US Hit http://us.archive.ubuntu.com oneiric-proposed/restricted i386 Packages Hit http://us.archive.ubuntu.com oneiric-proposed/main i386 Packages Hit http://us.archive.ubuntu.com oneiric-proposed/multiverse i386 Packages Hit http://us.archive.ubuntu.com oneiric-proposed/universe i386 Packages Hit http://us.archive.ubuntu.com oneiric-proposed/main TranslationIndex Hit http://us.archive.ubuntu.com oneiric-proposed/multiverse TranslationIndex Hit http://us.archive.ubuntu.com oneiric-proposed/restricted TranslationIndex Hit http://us.archive.ubuntu.com oneiric-proposed/universe TranslationIndex Ign http://archive.canonical.com oneiric/partner Translation-en_US Ign http://extras.ubuntu.com oneiric/main Translation-en Ign http://ppa.launchpad.net oneiric/main Translation-en Ign http://archive.canonical.com oneiric/partner Translation-en Get:1 http://us.archive.ubuntu.com oneiric/main i386 Packages [1,583 kB] Hit http://us.archive.ubuntu.com oneiric/main Translation-en Hit http://us.archive.ubuntu.com oneiric/multiverse Translation-en Hit http://us.archive.ubuntu.com oneiric/restricted Translation-en Hit http://us.archive.ubuntu.com oneiric/universe Translation-en Hit http://us.archive.ubuntu.com oneiric-updates/main Translation-en Hit http://us.archive.ubuntu.com oneiric-updates/multiverse Translation-en Hit http://us.archive.ubuntu.com oneiric-updates/restricted Translation-en Hit http://us.archive.ubuntu.com oneiric-updates/universe Translation-en Hit http://us.archive.ubuntu.com oneiric-backports/main Translation-en Hit http://us.archive.ubuntu.com oneiric-backports/multiverse Translation-en Hit http://us.archive.ubuntu.com oneiric-backports/restricted Translation-en Hit http://us.archive.ubuntu.com oneiric-backports/universe Translation-en Hit http://us.archive.ubuntu.com oneiric-proposed/main Translation-en Hit http://us.archive.ubuntu.com oneiric-proposed/multiverse Translation-en Hit http://us.archive.ubuntu.com oneiric-proposed/restricted Translation-en Hit http://us.archive.ubuntu.com oneiric-proposed/universe Translation-en Err http://us.archive.ubuntu.com oneiric/main i386 Packages 404 Not Found [IP: 91.189.92.179 80] Fetched 1 B in 2s (0 B/s) W: Failed to fetch http://us.archive.ubuntu.com/ubuntu/dists/oneiric/main/binary-i386/Packages 404 Not Found [IP: 91.189.92.179 80] E: Some index files failed to download. They have been ignored, or old ones used instead.

Read the article

Solaris 10 branded zone VM Templates for Solaris 11 on OTN

- by jsavit

Early this year I wrote the article Ours Goes To 11 which describes the ability to import Solaris 10 systems into a "Solaris 10 branded zone" under Oracle Solaris 11. I did this using Solaris 11 Express, and the capability remains in Solaris 11 with only slight changes. This important tool lets you painlessly inhaling a Solaris Container from Solaris 10 or entire Solaris 10 systems ("the global zone") into virtualized environments on a Solaris 11 OS. Just recently, Oracle provided Oracle VM Templates for Oracle Solaris 10 Zones to let you create Solaris 10 branded zones for Solaris 11 even if you don't currently have access to install media or a running Solaris 10 system. To use this, just download the Oracle VM Template for Oracle Solaris Zone 10 from OTN at http://www.oracle.com/technetwork/server-storage/solaris11/downloads/virtual-machines-1355605.html. This page contains images of Oracle Solaris 10 8/11 (the recent update to Solaris 10) in SPARC and x86 formats suitable for creating branded zones. The same page also has a VirtualBox image you can download for a complete Solaris 10 install in a guest virtual machine you can run on any host OS that supports VirtualBox. Both sets of downloads provide a quick - and extremely easy - way to set up a virtual Solaris 10 environment. In the case of the Oracle VM Templates, they illustrate several advanced features of Solaris 11. To start, just go to the above link, download the template for the hardware platform (SPARC or x86) you want, and download the README file also linked from that page. Install prerequisites The README file tells you to install the prerequisite Solaris 11 package that implements the Solaris 10 brand. Then you can install instances of zones with that brand. # pkg install pkg:/system/zones/brand/brand-solaris10 Packages to install: 1 Create boot environment: No Create backup boot environment: Yes DOWNLOAD PKGS FILES XFER (MB) Completed 1/1 44/44 0.4/0.4 PHASE ACTIONS Install Phase 74/74 PHASE ITEMS Package State Update Phase 1/1 Image State Update Phase 2/2 That took only a few minutes, and didn't require a reboot. Install the Solaris 10 zone Now it's time to run the downloaded template file. First make it executable via the chmod command, of course. I found that (unlike stated in the README) there was no need to rename the downloaded file to remove the .bin. When you run it you provide several parameters to describe the zone configuration: -a IP address - the IP address and optional netmask for the zone. This is the only mandatory parameter. -z zonename - the name of the zone you would like to create. -i interface - the package will create an exclusive-IP zone using a virtual NIC (vnic) based on this physical interface. In my case, I have a NIC called rge0. -p PATH - specifies the path in which you want the zoneroot to be placed. In my case, I have a ZFS dataset mounted at /zones, and this will create a zoneroot at /zones/s10u10. Kicking it off, you will see a copyright message, and then messages showing progress building the zone, which only takes a few minutes. # ./solaris-10u10-x86.bin -p /zones -a 192.168.1.100 -i rge0 -z s10u10 ... ... Checking disk-space for extraction Ok Extracting in /export/home/CDimages/s10zone/bootimage.ihaqvh ... 100% [===============================] Checking data integrity Ok Checking platform compatibility The host and the image do not have the same Solaris release: host Solaris release: 5.11 image Solaris release: 5.10 Will create a Solaris 10 branded zone. Warning: could not find a defaultrouter Zone won't have any defaultrouter configured IMAGE: ./solaris-10u10-x86.bin ZONE: s10u10 ZONEPATH: /zones/s10u10 INTERFACE: rge0 VNIC: vnicZBI13379 MAC ADDR: 2:8:20:5c:1a:cc IP ADDR: 192.168.1.100 NETMASK: 255.255.255.0 DEFROUTER: NONE TIMEZONE: US/Arizona Checking disk-space for installation Ok Installing in /zones/s10u10 ... 100% [===============================] Using a static exclusive-IP Attaching s10u10 Booting s10u10 Waiting for boot to complete booting... booting... booting... Zone s10u10 booted The zone's root password has been set using the root password of the local host. You can change the zone's root password to further harden the security of the zone: being root, log into the zone from the local host with the command 'zlogin s10u10'. Once logged in, change the root password with the command 'passwd'. The nifty part in my opinion (besides being so easy), is that the zone was created as an exclusive-IP zone on a virtual NIC. This network configuration lets you enforce traffic isolation from other zones, enforce network Quality of Service, and even let the zone set its own characteristics like IP address and packet size. Independence of the zone's network characteristics from the global zone is one of the enhancements in Solaris 10 that make it easier to consolidate zones while preserving their autonomy, yet provide control in a consolidated environment. Let's see what the virtual network environment looks like by issuing commands from the Solaris 11 global zone. First I'll use Old School ifconfig, and then I'll use the new ipadm and dladm commands. # ifconfig -a4 lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 rge0: flags=1004943<UP,BROADCAST,RUNNING,PROMISC,MULTICAST,DHCP,IPv4> mtu 1500 index 2 inet 192.168.1.3 netmask ffffff00 broadcast 192.168.1.255 ether 0:14:d1:18:ac:bc vboxnet0: flags=201000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4,CoS> mtu 1500 index 3 inet 192.168.56.1 netmask ffffff00 broadcast 192.168.56.255 ether 8:0:27:f8:62:1c # dladm show-phys LINK MEDIA STATE SPEED DUPLEX DEVICE yge0 Ethernet unknown 0 unknown yge0 yge1 Ethernet unknown 0 unknown yge1 rge0 Ethernet up 1000 full rge0 vboxnet0 Ethernet up 1000 full vboxnet0 # dladm show-link LINK CLASS MTU STATE OVER yge0 phys 1500 unknown -- yge1 phys 1500 unknown -- rge0 phys 1500 up -- vboxnet0 phys 1500 up -- vnicZBI13379 vnic 1500 up rge0 s10u10/vnicZBI13379 vnic 1500 up rge0 s10u10/net0 vnic 1500 up rge0 # dladm show-vnic LINK OVER SPEED MACADDRESS MACADDRTYPE VID vnicZBI13379 rge0 1000 2:8:20:5c:1a:cc random 0 s10u10/vnicZBI13379 rge0 1000 2:8:20:5c:1a:cc random 0 s10u10/net0 rge0 1000 2:8:20:9d:d0:79 random 0 # ipadm show-addr ADDROBJ TYPE STATE ADDR lo0/v4 static ok 127.0.0.1/8 rge0/_a dhcp ok 192.168.1.3/24 vboxnet0/_a static ok 192.168.56.1/24 lo0/v6 static ok ::1/128 Log into the zone The install step already booted the zone, so lets log into it. Notice how you have to be appropriately privileged to log into a zone. This is my home system so I'm being a bit cavalier, but in a production environment you can give granular control of who can login to which zones. Voila! a Solaris 10 environment under a Solaris 11 kernel. Notice the output from the uname -a and ifconfig commands, and output from a ping to a nearby host. $ zlogin s10u10 zlogin: You lack sufficient privilege to run this command (all privs required) savit@home:~$ sudo zlogin s10u10 Password: [Connected to zone 's10u10' pts/5] Oracle Corporation SunOS 5.10 Generic Patch January 2005 # uname -a SunOS s10u10 5.10 Generic_Virtual i86pc i386 i86pc # ifconfig -a4 lo0: flags=2001000849 mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 vnicZBI13379: flags=1000843 mtu 1500 index 2 inet 192.168.1.100 netmask ffffff00 broadcast 192.168.1.255 ether 2:8:20:5c:1a:cc # bash bash-3.2# ifconfig -a lo0: flags=2001000849 mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 vnicZBI13379: flags=1000843 mtu 1500 index 2 inet 192.168.1.100 netmask ffffff00 broadcast 192.168.1.255 ether 2:8:20:5c:1a:cc bash-3.2# ping 192.168.1.2 192.168.1.2 is alive For fun, I configured Apache (setting its configuration file in /etc/apache2) and brought it up. Easy - took just a few minutes. bash-3.2# svcs apache2 STATE STIME FMRI disabled 12:38:46 svc:/network/http:apache2 bash-3.2# svcadm enable apache2 Summary In just a few minutes, I built a functioning virtual Solaris 10 environment under by Solaris 11 system. It was... easy! While I can still do it the manual way (creating and using a system archive), this is a low-effort way to create a Solaris 10 zone on Solaris 11.

Read the article

Package Dependencies Error in almost every install

- by Betaxpression

New to Ubuntu. In the other sofware sources i have "Debian 4.0 eth" officially supported "non-us.debian.org/"; etc ... "ppa.launcpad.net" and installing applications has stopped working. I think i first came across this problem after installing Blender 2.58 When using update manager it is prompting for a partial upgrade. Almost every software when trying to install showing the same error Package Dependencies Error or GPG PUB KEY missing, tried to fixing to them but no luck. Output to: sudo apt-get update && sudo apt-get upgrade (links disabled http:// -- http:/ as new user can't put more no. of hyperlinks) Ign http:/non-us.debian.org stable/non-US InRelease Ign http:/non-us.debian.org stable/non-US Release.gpg Ign http:/non-us.debian.org stable/non-US Release Ign http:/non-us.debian.org stable/non-US/contrib TranslationIndex Ign http:/non-us.debian.org stable/non-US/main TranslationIndex Ign http:/non-us.debian.org stable/non-US/non-free TranslationIndex Err http:/non-us.debian.org stable/non-US/main Sources 503 Service Unavailable Err http:/non-us.debian.org stable/non-US/contrib Sources 503 Service Unavailable Err http:/non-us.debian.org stable/non-US/non-free Sources 503 Service Unavailable Err http:/non-us.debian.org stable/non-US/main amd64 Packages 503 Service Unavailable Err http:/non-us.debian.org stable/non-US/contrib amd64 Packages 503 Service Unavailable Err http:/non-us.debian.org stable/non-US/non-free amd64 Packages 503 Service Unavailable Ign http:/non-us.debian.org stable/non-US/contrib Translation-en_IN Ign http:/non-us.debian.org stable/non-US/contrib Translation-en Ign http:/non-us.debian.org stable/non-US/main Translation-en_IN Ign http:/non-us.debian.org stable/non-US/main Translation-en Ign http:/non-us.debian.org stable/non-US/non-free Translation-en_IN Ign http:/non-us.debian.org stable/non-US/non-free Translation-en Ign http:/archive.ubuntu.com natty InRelease Ign http:/archive.canonical.com natty InRelease Ign http:/extras.ubuntu.com natty InRelease Ign http:/http.us.debian.org stable InRelease Ign http:/ftp.us.debian.org etch InRelease Ign http:/archive.ubuntu.com natty-updates InRelease Hit http:/archive.canonical.com natty Release.gpg Get:1 http:/extras.ubuntu.com natty Release.gpg [72 B] Ign http:/ppa.launchpad.net natty InRelease Get:2 http:/http.us.debian.org stable Release.gpg [1,672 B] Ign http:/linux.dropbox.com natty InRelease Ign http:/ftp.us.debian.org etch Release.gpg Ign http:/archive.ubuntu.com natty-security InRelease Hit http:/archive.canonical.com natty Release Hit http:/extras.ubuntu.com natty Release Ign http:/ppa.launchpad.net natty InRelease Get:3 http:/linux.dropbox.com natty Release.gpg [489 B] Ign http:/ftp.us.debian.org etch Release Ign http:/dl.google.com stable InRelease Get:4 http:/archive.ubuntu.com natty Release.gpg [198 B] Ign http:/ppa.launchpad.net natty InRelease Hit http:/archive.canonical.com natty/partner Sources Hit http:/extras.ubuntu.com natty/main Sources Get:5 http:/linux.dropbox.com natty Release [2,599 B] Get:6 http:/archive.ubuntu.com natty-updates Release.gpg [198 B] Ign http:/ppa.launchpad.net natty InRelease Hit http:/archive.canonical.com natty/partner amd64 Packages Hit http:/extras.ubuntu.com natty/main amd64 Packages Get:7 http:/linux.dropbox.com natty/main amd64 Packages [784 B] Get:8 http:/archive.ubuntu.com natty-security Release.gpg [198 B] Ign http:/ppa.launchpad.net natty InRelease Ign http:/archive.canonical.com natty/partner TranslationIndex Ign http:/extras.ubuntu.com natty/main TranslationIndex Get:9 http:/http.us.debian.org stable Release [104 kB] Ign http:/linux.dropbox.com natty/main TranslationIndex Hit http:/archive.ubuntu.com natty Release Ign http:/ppa.launchpad.net natty InRelease Ign http:/http.us.debian.org stable Release Hit http:/archive.ubuntu.com natty-updates Release Get:10 http:/ppa.launchpad.net natty InRelease [316 B] Ign http:/ppa.launchpad.net natty InRelease Hit http:/archive.ubuntu.com natty-security Release Get:11 http:/ppa.launchpad.net natty InRelease [316 B] Ign http:/ppa.launchpad.net natty InRelease Hit http:/archive.ubuntu.com natty/restricted Sources Get:12 http:/ppa.launchpad.net natty Release.gpg [316 B] Ign http:/http.us.debian.org stable/main Sources/DiffIndex Get:13 http:/ppa.launchpad.net natty Release.gpg [316 B] Hit http:/archive.ubuntu.com natty/main Sources Ign http:/ftp.us.debian.org etch/contrib TranslationIndex Ign http:/http.us.debian.org stable/contrib Sources/DiffIndex Get:14 http:/ppa.launchpad.net natty Release.gpg [1,502 B] Ign http:/http.us.debian.org stable/non-free Sources/DiffIndex Ign http:/ftp.us.debian.org etch/main TranslationIndex Get:15 http:/ppa.launchpad.net natty Release.gpg [1,928 B] Ign http:/http.us.debian.org stable/main amd64 Packages/DiffIndex Ign http:/ftp.us.debian.org etch/non-free TranslationIndex Ign http:/ppa.launchpad.net natty Release.gpg Hit http:/http.us.debian.org stable/contrib amd64 Packages/DiffIndex W: GPG error: http:/http.us.debian.org stable Release: The following signatures couldn't be verified because the public key is not available: NO_PUBKEY AED4B06F473041FA NO_PUBKEY 64481591B98321F9 W: GPG error: http:/ppa.launchpad.net natty InRelease: File /var/lib/apt/lists/partial/ppa.launchpad.net_sunab_kdenlive-release_ubuntu_dists_natty_InRelease doesn't start with a clearsigned message W: GPG error: http:/ppa.launchpad.net natty InRelease: File /var/lib/apt/lists/partial/ppa.launchpad.net_ubuntu-wine_ppa_ubuntu_dists_natty_InRelease doesn't start with a clearsigned message E: Could not open file /var/lib/apt/lists/http.us.debian.org_debian_dists_stable_contrib_binary-amd64_Packages.IndexDiff - open (2: No such file or directory) output to: sudo cat /etc/apt/sources.list # deb cdrom:[Ubuntu 11.04 _Natty Narwhal_ - Release amd64 (20110427.1)]/ natty main restricted # See http:/help.ubuntu.com/community/UpgradeNotes for how to upgrade to # newer versions of the distribution. deb http:/archive.ubuntu.com/ubuntu natty main restricted deb-src http:/archive.ubuntu.com/ubuntu natty restricted main multiverse universe #Added by software-properties ## Major bug fix updates produced after the final release of the ## distribution. deb http:/archive.ubuntu.com/ubuntu natty-updates main restricted deb-src http:/archive.ubuntu.com/ubuntu natty-updates restricted main multiverse universe #Added by software-properties ## N.B. software from this repository is ENTIRELY UNSUPPORTED by the Ubuntu ## team. Also, please note that software in universe WILL NOT receive any ## review or updates from the Ubuntu security team. deb http:/archive.ubuntu.com/ubuntu natty universe deb http:/archive.ubuntu.com/ubuntu natty-updates universe ## N.B. software from this repository is ENTIRELY UNSUPPORTED by the Ubuntu ## team, and may not be under a free licence. Please satisfy yourself as to ## your rights to use the software. Also, please note that software in ## multiverse WILL NOT receive any review or updates from the Ubuntu ## security team. deb http:/archive.ubuntu.com/ubuntu natty multiverse deb http:/archive.ubuntu.com/ubuntu natty-updates multiverse ## Uncomment the following two lines to add software from the 'backports' ## repository. ## N.B. software from this repository may not have been tested as ## extensively as that contained in the main release, although it includes ## newer versions of some applications which may provide useful features. ## Also, please note that software in backports WILL NOT receive any review ## or updates from the Ubuntu security team. # deb http:/us.archive.ubuntu.com/ubuntu/ natty-backports main restricted universe multiverse # deb-src http:/us.archive.ubuntu.com/ubuntu/ natty-backports main restricted universe multiverse deb http:/archive.ubuntu.com/ubuntu natty-security main restricted deb-src http:/archive.ubuntu.com/ubuntu natty-security restricted main multiverse universe #Added by software-properties deb http:/archive.ubuntu.com/ubuntu natty-security universe deb http:/archive.ubuntu.com/ubuntu natty-security multiverse ## Uncomment the following two lines to add software from Canonical's ## 'partner' repository. ## This software is not part of Ubuntu, but is offered by Canonical and the ## respective vendors as a service to Ubuntu users. deb http:/archive.canonical.com/ubuntu natty partner deb-src http:/archive.canonical.com/ubuntu natty partner ## This software is not part of Ubuntu, but is offered by third-party ## developers who want to ship their latest software. deb http:/extras.ubuntu.com/ubuntu natty main deb-src http:/extras.ubuntu.com/ubuntu natty main deb http:/ftp.us.debian.org/debian/ etch main contrib non-free deb-src http:/ftp.us.debian.org/debian/ etch main contrib non-free deb http:/http.us.debian.org/debian stable main contrib non-free deb-src http:/http.us.debian.org/debian stable main contrib non-free deb http:/non-us.debian.org/debian-non-US stable/non-US main contrib non-free deb-src http:/non-us.debian.org/debian-non-US stable/non-US main contrib non-free Thanks But after removing Debian repositories still getting this error: W:GPG error: http://ppa.launchpad.net natty Release: The following signatures couldn't be verified because the public key is not available: NO_PUBKEY 9BDB3D89CE49EC21, W:GPG error: http://ppa.launchpad.net natty Release: The following signatures couldn't be verified because the public key is not available: NO_PUBKEY 80E7349A06ED541C, W:GPG error: http://ppa.launchpad.net natty Release: The following signatures couldn't be verified because the public key is not available: NO_PUBKEY 8C851674F96FD737, W:GPG error: http://ppa.launchpad.net natty Release: The following signatures couldn't be verified because the public key is not available: NO_PUBKEY 94E58C34A8670E8C, E:Unable to parse package file /var/lib/apt/lists/partial/archive.ubuntu.com_ubuntu_dists_natty-updates_multiverse_i18n_Index (1) I actually tried this before, but i am always getting this error --Executing: gpg --ignore-time-conflict --no-options --no-default-keyring --secret-keyring /etc/apt/secring.gpg --trustdb-name /etc/apt/trustdb.gpg --keyring /etc/apt/trusted.gpg --primary-keyring /etc/apt/trusted.gpg --keyserver keyserver.ubuntu.com --recv-keys 8C851674F96FD737 gpg: requesting key F96FD737 from hkp server keyserver.ubuntu.com ?: keyserver.ubuntu.com: Connection refused gpgkeys: HTTP fetch error 7: couldn't connect: Connection refused gpg: no valid OpenPGP data found. gpg: Total number processed: 0

Read the article

Multi-tenant ASP.NET MVC - Views

- by zowens

Part I – Introduction Part II – Foundation Part III – Controllers So far we have covered the basic premise of tenants and how they will be delegated. Now comes a big issue with multi-tenancy, the views. In some applications, you will not have to override views for each tenant. However, one of my requirements is to add extra views (and controller actions) along with overriding views from the core structure. This presents a bit of a problem in locating views for each tenant request. I have chosen quite an opinionated approach at the present but will coming back to the “views” issue in a later post. What’s the deal? The path I’ve chosen is to use precompiled Spark views. I really love Spark View Engine and was planning on using it in my project anyways. However, I ran across a really neat aspect of the source when I was having a look under the hood. There’s an easy way to hook in embedded views from your project. There are solutions that provide this, but they implement a special Virtual Path Provider. While I think this is a great solution, I would rather just have Spark take care of the view resolution. The magic actually happens during the compilation of the views into a bin-deployable DLL. After the views are compiled, the are simply pulled out of the views DLL. Each tenant has its own views DLL that just has “.Views” appended after the assembly name as a convention. The list of reasons for this approach are quite long. The primary motivation is performance. I’ve had quite a few performance issues in the past and I would like to increase my application’s performance in any way that I can. My customized build of Spark removes insignificant whitespace from the HTML output so I can some some bandwidth and load time without having to deal with whitespace removal at runtime. How to setup Tenants for the Host In the source, I’ve provided a single tenant as a sample (Sample1). This will serve as a template for subsequent tenants in your application. The first step is to add a “PostBuildStep” installer into the project. I’ve defined one in the source that will eventually change as we focus more on the construction of dependency containers. The next step is to tell the project to run the installer and copy the DLL output to a folder in the host that will pick up as a tenant. Here’s the code that will achieve it (this belongs in Post-build event command line field in the Build Events tab of settings) %systemroot%\Microsoft.NET\Framework\v4.0.30319\installutil "$(TargetPath)" copy /Y "$(TargetDir)$(TargetName)*.dll" "$(SolutionDir)Web\Tenants\" copy /Y "$(TargetDir)$(TargetName)*.pdb" "$(SolutionDir)Web\Tenants\" The DLLs with a name starting with the target assembly name will be copied to the “Tenants” folder in the web project. This means something like MultiTenancy.Tenants.Sample1.dll and MultiTenancy.Tenants.Sample1.Views.dll will both be copied along with the debug symbols. This is probably the simplest way to go about this, but it is a tad inflexible. For example, what if you have dependencies? The preferred method would probably be to use IL Merge to merge your dependencies with your target DLL. This would have to be added in the build events. Another way to achieve that would be to simply bypass Visual Studio events and use MSBuild. I also got a question about how I was setting up the controller factory. Here’s the basics on how I’m setting up tenants inside the host (Global.asax) protected void Application_Start() { RegisterRoutes(RouteTable.Routes); // create a container just to pull in tenants var topContainer = new Container(); topContainer.Configure(config => { config.Scan(scanner => { scanner.AssembliesFromPath(Path.Combine(Server.MapPath("~/"), "Tenants")); scanner.AddAllTypesOf<IApplicationTenant>(); }); }); // create selectors var tenantSelector = new DefaultTenantSelector(topContainer.GetAllInstances<IApplicationTenant>()); var containerSelector = new TenantContainerResolver(tenantSelector); // clear view engines, we don't want anything other than spark ViewEngines.Engines.Clear(); // set view engine ViewEngines.Engines.Add(new TenantViewEngine(tenantSelector)); // set controller factory ControllerBuilder.Current.SetControllerFactory(new ContainerControllerFactory(containerSelector)); } The code to setup the tenants isn’t actually that hard. I’m utilizing assembly scanners in StructureMap as a simple way to pull in DLLs that are not in the AppDomain. Remember that there is a dependency on the host in the tenants and a tenant cannot simply be referenced by a host because of circular dependencies. Tenant View Engine TenantViewEngine is a simple delegator to the tenant’s specified view engine. You might have noticed that a tenant has to define a view engine. public interface IApplicationTenant { .... IViewEngine ViewEngine { get; } } The trick comes in specifying the view engine on the tenant side. Here’s some of the code that will pull views from the DLL. protected virtual IViewEngine DetermineViewEngine() { var factory = new SparkViewFactory(); var file = GetType().Assembly.CodeBase.Without("file:///").Replace(".dll", ".Views.dll").Replace('/', '\\'); var assembly = Assembly.LoadFile(file); factory.Engine.LoadBatchCompilation(assembly); return factory; } This code resides in an abstract Tenant where the fields are setup in the constructor. This method (inside the abstract class) will load the Views assembly and load the compilation into Spark’s “Descriptors” that will be used to determine views. There is some trickery on determining the file location… but it works just fine. Up Next There’s just a few big things left such as StructureMap configuring controllers with a convention instead of specifying types directly with container construction and content resolution. I will also try to find a way to use the Web Forms View Engine in a multi-tenant way we achieved with the Spark View Engine without using a virtual path provider. I will probably not use the Web Forms View Engine personally, but I’m sure some people would prefer using WebForms because of the maturity of the engine. As always, I love to take questions by email or on twitter. Suggestions are always welcome as well! (Oh, and here’s another link to the source code).

Read the article

Create PDF document using iTextSharp in ASP.Net 4.0 and MemoryMappedFile

- by sreejukg

In this article I am going to demonstrate how ASP.Net developers can programmatically create PDF documents using iTextSharp. iTextSharp is a software component, that allows developers to programmatically create or manipulate PDF documents. Also this article discusses the process of creating in-memory file, read/write data from/to the in-memory file utilizing the new feature MemoryMappedFile. I have a database of users, where I need to send a notice to all my users as a PDF document. The sending mail part of it is not covered in this article. The PDF document will contain the company letter head, to make it more official. I have a list of users stored in a database table named “tblusers”. For each user I need to send customized message addressed to them personally. The database structure for the users is give below. id Title Full Name 1 Mr. Sreeju Nair K. G. 2 Dr. Alberto Mathews 3 Prof. Venketachalam Now I am going to generate the pdf document that contains some message to the user, in the following format. Dear <Title> <FullName>, The message for the user. Regards, Administrator Also I have an image, bg.jpg that contains the background for the document generated. I have created .Net 4.0 empty web application project named “iTextSharpSample”. First thing I need to do is to download the iTextSharp dll from the source forge. You can find the url for the download here. http://sourceforge.net/projects/itextsharp/files/ I have extracted the Zip file and added the itextsharp.dll as a reference to my project. Also I have added a web form named default.aspx to my project. After doing all this, the solution explorer have the following view. In the default.aspx page, I inserted one grid view and associated it with a SQL Data source control that bind data from tblusers. I have added a button column in the grid view with text “generate pdf”. The output of the page in the browser is as follows. Now I am going to create a pdf document when the user clicking on the Generate PDF button. As I mentioned before, I am going to work with the file in memory, I am not going to create a file in the disk. I added an event handler for button by specifying onrowcommand event handler. My gridview source looks like <asp:GridView ID="GridView1" runat="server" AutoGenerateColumns="False" DataSourceID="SqlDataSource1" Width="481px" CellPadding="4" ForeColor="#333333" GridLines="None" onrowcommand="Generate_PDF" > ………………………………………………………………………….. ………………………………………………………………………….. </asp:GridView> In the code behind, I wrote the corresponding event handler. protected void Generate_PDF(object sender, GridViewCommandEventArgs e) { // The button click event handler code. // I am going to explain the code for this section in the remaining part of the article } The Generate_PDF method is straight forward, It get the title, fullname and message to some variables, then create the pdf using these variables. The code for getting data from the grid view is as follows // get the row index stored in the CommandArgument property int index = Convert.ToInt32(e.CommandArgument); // get the GridViewRow where the command is raised GridViewRow selectedRow = ((GridView)e.CommandSource).Rows[index]; string title = selectedRow.Cells[1].Text; string fullname = selectedRow.Cells[2].Text; string msg = @"There are some changes in the company policy, due to this matter you need to submit your latest address to us. Please update your contact details / personnal details by visiting the member area of the website. ................................... "; since I don’t want to save the file in the disk, I am going the new feature introduced in .Net framework 4, called Memory-Mapped Files. Using Memory-Mapped mapped file, you can created non-persisted memory mapped files, that are not associated with a file in a disk. So I am going to create a temporary file in memory, add the pdf content to it, then write it to the output stream. To read more about MemoryMappedFile, read this msdn article http://msdn.microsoft.com/en-us/library/dd997372.aspx The below portion of the code using MemoryMappedFile object to create a test pdf document in memory and perform read/write operation on file. The CreateViewStream() object will give you a stream that can be used to read or write data to/from file. The code is very straight forward and I included comment so that you can understand the code. using (MemoryMappedFile mmf = MemoryMappedFile.CreateNew("test1.pdf", 1000000)) { // Create a new pdf document object using the constructor. The parameters passed are document size, left margin, right margin, top margin and bottom margin. iTextSharp.text.Document d = new iTextSharp.text.Document(PageSize.A4, 72,72,172,72); //get an instance of the memory mapped file to stream object so that user can write to this using (MemoryMappedViewStream stream = mmf.CreateViewStream()) { // associate the document to the stream. PdfWriter.GetInstance(d, stream); /* add an image as bg*/ iTextSharp.text.Image jpg = iTextSharp.text.Image.GetInstance(Server.MapPath("Image/bg.png")); jpg.Alignment = iTextSharp.text.Image.UNDERLYING; jpg.SetAbsolutePosition(0, 0); //this is the size of my background letter head image. the size is in points. this will fit to A4 size document. jpg.ScaleToFit(595, 842); d.Open(); d.Add(jpg); d.Add(new Paragraph(String.Format("Dear {0} {1},", title, fullname))); d.Add(new Paragraph("\n")); d.Add(new Paragraph(msg)); d.Add(new Paragraph("\n")); d.Add(new Paragraph(String.Format("Administrator"))); d.Close(); } //read the file data byte[] b; using (MemoryMappedViewStream stream = mmf.CreateViewStream()) { BinaryReader rdr = new BinaryReader(stream); b = new byte[mmf.CreateViewStream().Length]; rdr.Read(b, 0, (int)mmf.CreateViewStream().Length); } Response.Clear(); Response.ContentType = "Application/pdf"; Response.BinaryWrite(b); Response.End(); } Press ctrl + f5 to run the application. First I got the user list. Click on the generate pdf icon. The created looks as follows. Summary: Creating pdf document using iTextSharp is easy. You will get lot of information while surfing the www. Some useful resources and references are mentioned below http://itextsharp.com/ http://www.mikesdotnetting.com/Article/82/iTextSharp-Adding-Text-with-Chunks-Phrases-and-Paragraphs http://somewebguy.wordpress.com/2009/05/08/itextsharp-simplify-your-html-to-pdf-creation/ Hope you enjoyed the article.

Read the article

My nVidia GeForce 8600M GT card stopped working: "extension GLX missing on display 0:0"

- by Wolter Hellmund

So I turned on my computer and log into my gnome-shell session to find that the shell is gone, and there is instead a very thick panel with a vertically repeated pattern of the gradient the Unity panel displays. I ran some tests and found out that my graphic acceleration was failing. I have attached some outputs of some commands to help helpers help me: Some command outputs Video card: nVidia GeForce 8600M GT (note that it is not an Optimus card). Output of lspci | grep VGA: 01:00.0 VGA compatible controller: NVIDIA Corporation G84 [GeForce 8600M GT] (rev a1) Output of glxinfo: Xlib: extension "GLX" missing on display ":0.0". Xlib: extension "GLX" missing on display ":0.0". Xlib: extension "GLX" missing on display ":0.0". Xlib: extension "GLX" missing on display ":0.0". Xlib: extension "GLX" missing on display ":0.0". Error: couldn't find RGB GLX visual or fbconfig Xlib: extension "GLX" missing on display ":0.0". Xlib: extension "GLX" missing on display ":0.0". Xlib: extension "GLX" missing on display ":0.0". Xlib: extension "GLX" missing on display ":0.0". Xlib: extension "GLX" missing on display ":0.0". Contents of /var/log/Xorg.0.log: NVIDIA: Failed to load the NVIDIA kernel module. Please check your NVIDIA: system's kernel log for additional error messages. UnloadModule: "nvidia" Unloading nvidia Failed to load module "nvidia" (module-specific error, 0) If I use the Aditional Drivers system application, I see none of the drivers active, and when I try to activate any, I get an error telling me to check the jockey.log file. The contents of /var/log/jockey.log are: 2012-09-20 23:11:32,690 DEBUG: NVidia(nvidia_173).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:32,690 DEBUG: nvidia_173 is not the alternative in use 2012-09-20 23:11:34,606 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: enabled, b43legacy: enabled 2012-09-20 23:11:34,657 DEBUG: NVidia(nvidia_173_updates).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:34,657 DEBUG: nvidia_173_updates is not the alternative in use 2012-09-20 23:11:36,647 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:36,648 DEBUG: KMH enabled: False 2012-09-20 23:11:38,642 DEBUG: NVidia(nvidia_current_updates).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:38,642 DEBUG: nvidia_current_updates is not the alternative in use 2012-09-20 23:11:40,546 DEBUG: NVidia(nvidia_173).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:40,546 DEBUG: nvidia_173 is not the alternative in use 2012-09-20 23:11:40,620 DEBUG: NVidia(nvidia_173).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:40,620 DEBUG: nvidia_173 is not the alternative in use 2012-09-20 23:11:40,629 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: enabled, b43legacy: enabled 2012-09-20 23:11:40,698 DEBUG: NVidia(nvidia_173_updates).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:40,698 DEBUG: nvidia_173_updates is not the alternative in use 2012-09-20 23:11:40,759 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:40,760 DEBUG: KMH enabled: False 2012-09-20 23:11:40,826 DEBUG: NVidia(nvidia_current_updates).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:40,826 DEBUG: nvidia_current_updates is not the alternative in use 2012-09-20 23:11:45,415 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:45,415 DEBUG: KMH enabled: False 2012-09-20 23:11:47,367 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:11:47,367 DEBUG: KMH enabled: False 2012-09-20 23:11:55,961 WARNING: modinfo for module nvidia_current failed: ERROR: modinfo: could not find module nvidia_current 2012-09-20 23:11:55,962 ERROR: XorgDriverHandler.enable(): package or module not installed, aborting 2012-09-20 23:12:27,780 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:27,781 DEBUG: KMH enabled: False 2012-09-20 23:12:27,840 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:27,840 DEBUG: KMH enabled: False 2012-09-20 23:12:43,196 DEBUG: NVidia(nvidia_173).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,197 DEBUG: nvidia_173 is not the alternative in use 2012-09-20 23:12:43,208 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: enabled, b43legacy: enabled 2012-09-20 23:12:43,269 DEBUG: NVidia(nvidia_173_updates).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,269 DEBUG: nvidia_173_updates is not the alternative in use 2012-09-20 23:12:43,333 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,333 DEBUG: KMH enabled: False 2012-09-20 23:12:43,393 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,394 DEBUG: KMH enabled: False 2012-09-20 23:12:43,465 DEBUG: NVidia(nvidia_current_updates).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,465 DEBUG: nvidia_current_updates is not the alternative in use 2012-09-20 23:12:43,531 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,531 DEBUG: KMH enabled: False 2012-09-20 23:12:43,587 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,587 DEBUG: KMH enabled: False 2012-09-20 23:12:43,663 DEBUG: NVidia(nvidia_173).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,663 DEBUG: nvidia_173 is not the alternative in use 2012-09-20 23:12:43,672 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: enabled, b43legacy: enabled 2012-09-20 23:12:43,738 DEBUG: NVidia(nvidia_173_updates).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,739 DEBUG: nvidia_173_updates is not the alternative in use 2012-09-20 23:12:43,803 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,803 DEBUG: KMH enabled: False 2012-09-20 23:12:43,863 DEBUG: NVidia(nvidia_current).enabled(): target_alt /usr/lib/nvidia-current/ld.so.conf current_alt /usr/lib/nvidia-current/ld.so.conf other target alt /usr/lib/nvidia-current/alt_ld.so.conf other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,863 DEBUG: KMH enabled: False 2012-09-20 23:12:43,930 DEBUG: NVidia(nvidia_current_updates).enabled(): target_alt None current_alt /usr/lib/nvidia-current/ld.so.conf other target alt None other current alt /usr/lib/nvidia-current/alt_ld.so.conf 2012-09-20 23:12:43,930 DEBUG: nvidia_current_updates is not the alternative in use 2012-09-20 23:24:16,305 DEBUG: Shutting down Things I have tried Checked the video card on a Windows session. Reran nvidia-xconfig. Purged all nvidia software from my computer, and reinstall it. Run nvidia-xconfig. Tried a different kernel.

Read the article

Creating and maintaining Orchard translations

- by Bertrand Le Roy

Many volunteers have already stepped up to provide translations for Orchard. There are many challenges to overcome with translating such a project. Orchard is a very modular CMS, so the translation mechanism needs to account for the core as well as first and third party modules and themes. Another issue is that every new version of Orchard or of a module changes some localizable strings and adds new ones as others enter obsolescence. In order to address those problems, I've built a small Orchard module that automates some of the most complex tasks that maintaining a translation implies. In this post, I'll walk you through the operations I had to do to update the French translation for Orchard 1.0. In order to make sure you translate all the first party modules, I would recommend that you start from a full source code enlistment. The reason is that I'll show how you can extract the default en-US translation from any source code enlistment. That enables you to create a translation that is even more up-to-date than what is currently on the site. Alternatively, you could start by downloading the current en-US translation. If you decide to do so, just skip the relevant paragraphs. First, let's install the Orchard Translation Manager. I'm starting from a vanilla clone of the latest in the code repository. After you've setup the site, go into the dashboard and click on Gallery. Locate the Orchard Translation Manager in the list of modules and click "Install". Once the module is installed, you need to enable its one feature by going into Configuration/Features and clicking "Enable" next to Vandelay.TranslationManager. We're done with the setup that we need in order to start our translation work. We'll now switch to the command-line and to our favorite text editor. Open a command-line on the Orchard web site folder. I found the easiest way to do this is to do a SHIFT+right-click on the Orchard.Web folder in Windows Explorer and to click "Open command window here". Type bin\orchard to enter the Orchard command-line environment. If you do a "help commands" you should see four commands in the list that came from the module we just installed: extract default translation, install translation, package translation and sync translation. First, we're going to generate the default translation. Note that it is possible to generate that default translation for a specific list of modules and themes by using the /Extensions: switch, which should facilitate the translation of third party extensions, but in this tutorial we're going to generate it for the whole of the Orchard source code. extract default translation /Output:\temp .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } This should have created an Orchard.en-us.po.zip file in the temp directory. Extract that archive into an orchard.po folder under \temp. The next step depends on whether you have an existing translation that you want to update or not. If you do have an existing translation, just extract it into the same \temp\orchard.po directory. That should result in a file structure where you have the default en-US translation alongside your own. If you don't have an existing translation, just continue, the commands will be the same. We are now going to synchronize those translations (or generate the stub for a new one if you didn't start from an existing translation). sync translation /Input:\temp\orchard.po /Culture:fr-FR After this command (where you should of course substitute fr-FR with the culture you're working on), we now have updated files that contain a few useful flags. Open each of the .po files under the culture you are working on (there should be around 36) with your favorite text editor. For all the strings that are still valid in the latest version, nothing changes and you don't need to do anything. For all the strings that disappeared from the default culture, the old translation will still be there but they will be prefixed with the following comment: # Obsolete translation Conveniently, all the obsolete strings will be grouped at the end of the file. You can select all those and delete them. For all the new strings, you will see the following comment: # Untranslated string This is where the hard work begins. You'll need to translate each of those new strings by entering the translation between the quotes in: msgstr "" Don't introduce hard carriage returns in the strings, just stay on one line (your text editor should do some reasonable wrapping so this shouldn't be a big deal). Once you're done with a file, save it. Make sure, and this is very important, that your text editor is saving using the UTF-8 encoding. In Notepad, that setting can be found in the file saving dialog by doing a "Save As" rather than a plain "Save": When all the po files have been edited, you are ready to package the translation for submission (a.k.a. sending e-mail to the localization mailing list). package translation /Culture:fr-FR /Input:\temp\orchard.po /Output:\temp You should now see a Orchard.fr-FR.po.zip file in temp that is ready to be submitted. That is, once you've tested it, which can be done by deploying it into the site: install translation \temp\orchard.fr-fr.po.zip Once this is done you can go into the dashboard under Configuration/Settings and click on "Add or remove supported cultures for the site". Choose your culture and click "Add". You can go back to settings and set the default culture. Save. You may now take a tour of the application and verify that everything works as expected: And that's it really. Creating a translation for Orchard is a matter of a few hours. If you don't see a translation for your culture, please consider creating it.

Read the article

Using Radio Button in GridView with Validation

- by Vincent Maverick Durano

A developer is asking how to select one radio button at a time if the radio button is inside the GridView. As you may know setting the group name attribute of radio button will not work if the radio button is located within a Data Representation control like GridView. This because the radio button inside the gridview bahaves differentely. Since a gridview is rendered as table element , at run time it will assign different "name" to each radio button. Hence you are able to select multiple rows. In this post I'm going to demonstrate how select one radio button at a time in gridview and add a simple validation on it. To get started let's go ahead and fire up visual studio and the create a new web application / website project. Add a WebForm and then add gridview. The mark up would look something like this: <asp:GridView ID="GridView1" runat="server" AutoGenerateColumns="false" > <Columns> <asp:TemplateField> <ItemTemplate> <asp:RadioButton ID="rb" runat="server" /> </ItemTemplate> </asp:TemplateField> <asp:BoundField DataField="RowNumber" HeaderText="Row Number" /> <asp:BoundField DataField="Col1" HeaderText="First Column" /> <asp:BoundField DataField="Col2" HeaderText="Second Column" /> </Columns> </asp:GridView> Noticed that I've added a templatefield column so that we can add the radio button there. Also I have set up some BoundField columns and set the DataFields as RowNumber, Col1 and Col2. These columns are just dummy columns and i used it for the simplicity of this example. Now where these columns came from? These columns are created by hand at the code behind file of the ASPX. Here's the code below: private DataTable FillData() { DataTable dt = new DataTable(); DataRow dr = null; //Create DataTable columns dt.Columns.Add(new DataColumn("RowNumber", typeof(string))); dt.Columns.Add(new DataColumn("Col1", typeof(string))); dt.Columns.Add(new DataColumn("Col2", typeof(string))); //Create Row for each columns dr = dt.NewRow(); dr["RowNumber"] = 1; dr["Col1"] = "A"; dr["Col2"] = "B"; dt.Rows.Add(dr); dr = dt.NewRow(); dr["RowNumber"] = 2; dr["Col1"] = "AA"; dr["Col2"] = "BB"; dt.Rows.Add(dr); dr = dt.NewRow(); dr["RowNumber"] = 3; dr["Col1"] = "A"; dr["Col2"] = "B"; dt.Rows.Add(dr); dr = dt.NewRow(); dr["RowNumber"] = 4; dr["Col1"] = "A"; dr["Col2"] = "B"; dt.Rows.Add(dr); dr = dt.NewRow(); dr["RowNumber"] = 5; dr["Col1"] = "A"; dr["Col2"] = "B"; dt.Rows.Add(dr); return dt; } And here's the code for binding the GridView with the dummy data above. protected void Page_Load(object sender, EventArgs e) { if (!IsPostBack) { GridView1.DataSource = FillData(); GridView1.DataBind(); } } Okay we have now a GridView data with a radio button on each row. Now lets go ahead and switch back to ASPX mark up. In this example I'm going to use a JavaScript for validating the radio button to select one radio button at a time. Here's the javascript code below: function CheckOtherIsCheckedByGVID(rb) { var isChecked = rb.checked; var row = rb.parentNode.parentNode; if (isChecked) { row.style.backgroundColor = '#B6C4DE'; row.style.color = 'black'; } var currentRdbID = rb.id; parent = document.getElementById("<%= GridView1.ClientID %>"); var items = parent.getElementsByTagName('input'); for (i = 0; i < items.length; i++) { if (items[i].id != currentRdbID && items[i].type == "radio") { if (items[i].checked) { items[i].checked = false; items[i].parentNode.parentNode.style.backgroundColor = 'white'; items[i].parentNode.parentNode.style.color = '#696969'; } } } } The function above sets the row of the current selected radio button's style to determine that the row is selected and then loops through the radio buttons in the gridview and then de-select the previous selected radio button and set the row style back to its default. You can then call the javascript function above at onlick event of radio button like below: <asp:RadioButton ID="rb" runat="server" onclick="javascript:CheckOtherIsCheckedByGVID(this);" /> Here's the output below: On Load: After Selecting a Radio Button: As you have noticed, on initial load there's no default selected radio in the GridView. Now let's add a simple validation for that. We will basically display an error message if a user clicks a button that triggers a postback without selecting a radio button in the GridView. Here's the javascript for the validation: function ValidateRadioButton(sender, args) { var gv = document.getElementById("<%= GridView1.ClientID %>"); var items = gv.getElementsByTagName('input'); for (var i = 0; i < items.length ; i++) { if (items[i].type == "radio") { if (items[i].checked) { args.IsValid = true; return; } else { args.IsValid = false; } } } } The function above loops through the rows in gridview and find all the radio buttons within it. It will then check each radio button checked property. If a radio is checked then set IsValid to true else set it to false. The reason why I'm using IsValid is because I'm using the ASP validator control for validation. Now add the following mark up below under the GridView declaration: <br /> <asp:Label ID="lblMessage" runat="server" /> <br /> <asp:Button ID="btn" runat="server" Text="POST" onclick="btn_Click" ValidationGroup="GroupA" /> <asp:CustomValidator ID="CustomValidator1" runat="server" ErrorMessage="Please select row in the grid." ClientValidationFunction="ValidateRadioButton" ValidationGroup="GroupA" style="display:none"></asp:CustomValidator> <asp:ValidationSummary ID="ValidationSummary1" runat="server" ValidationGroup="GroupA" HeaderText="Error List:" DisplayMode="BulletList" ForeColor="Red" /> And then at Button Click event add this simple code below just to test if the validation works: protected void btn_Click(object sender, EventArgs e) { lblMessage.Text = "Postback at: " + DateTime.Now.ToString("hh:mm:ss tt"); } Here's the output below that you can see in the browser: That's it! I hope someone find this post useful! Technorati Tags: ASP.NET,JavaScript,GridView

Read the article

Java EE 6 and NoSQL/MongoDB on GlassFish using JPA and EclipseLink 2.4 (TOTD #175)

- by arungupta

TOTD #166 explained how to use MongoDB in your Java EE 6 applications. The code in that tip used the APIs exposed by the MongoDB Java driver and so requires you to learn a new API. However if you are building Java EE 6 applications then you are already familiar with Java Persistence API (JPA). Eclipse Link 2.4, scheduled to release as part of Eclipse Juno, provides support for NoSQL databases by mapping a JPA entity to a document. Their wiki provides complete explanation of how the mapping is done. This Tip Of The Day (TOTD) will show how you can leverage that support in your Java EE 6 applications deployed on GlassFish 3.1.2. Before we dig into the code, here are the key concepts ... A POJO is mapped to a NoSQL data source using @NoSQL or <no-sql> element in "persistence.xml". A subset of JPQL and Criteria query are supported, based upon the underlying data store Connection properties are defined in "persistence.xml" Now, lets lets take a look at the code ... Download the latest EclipseLink 2.4 Nightly Bundle. There is a Installer, Source, and Bundle - make sure to download the Bundle link (20120410) and unzip. Download GlassFish 3.1.2 zip and unzip. Install the Eclipse Link 2.4 JARs in GlassFish Remove the following JARs from "glassfish/modules": org.eclipse.persistence.antlr.jar org.eclipse.persistence.asm.jar org.eclipse.persistence.core.jar org.eclipse.persistence.jpa.jar org.eclipse.persistence.jpa.modelgen.jar org.eclipse.persistence.moxy.jar org.eclipse.persistence.oracle.jar Add the following JARs from Eclipse Link 2.4 nightly build to "glassfish/modules": org.eclipse.persistence.antlr_3.2.0.v201107111232.jar org.eclipse.persistence.asm_3.3.1.v201107111215.jar org.eclipse.persistence.core.jpql_2.4.0.v20120407-r11132.jar org.eclipse.persistence.core_2.4.0.v20120407-r11132.jar org.eclipse.persistence.jpa.jpql_2.0.0.v20120407-r11132.jar org.eclipse.persistence.jpa.modelgen_2.4.0.v20120407-r11132.jar org.eclipse.persistence.jpa_2.4.0.v20120407-r11132.jar org.eclipse.persistence.moxy_2.4.0.v20120407-r11132.jar org.eclipse.persistence.nosql_2.4.0.v20120407-r11132.jar org.eclipse.persistence.oracle_2.4.0.v20120407-r11132.jar Start MongoDB Download latest MongoDB from here (2.0.4 as of this writing). Create the default data directory for MongoDB as: sudo mkdir -p /data/db/sudo chown `id -u` /data/db Refer to Quickstart for more details. Start MongoDB as: arungup-mac:mongodb-osx-x86_64-2.0.4 <arungup> ->./bin/mongod./bin/mongod --help for help and startup optionsMon Apr 9 12:56:02 [initandlisten] MongoDB starting : pid=3124 port=27017 dbpath=/data/db/ 64-bit host=arungup-mac.localMon Apr 9 12:56:02 [initandlisten] db version v2.0.4, pdfile version 4.5Mon Apr 9 12:56:02 [initandlisten] git version: 329f3c47fe8136c03392c8f0e548506cb21f8ebfMon Apr 9 12:56:02 [initandlisten] build info: Darwin erh2.10gen.cc 9.8.0 Darwin Kernel Version 9.8.0: Wed Jul 15 16:55:01 PDT 2009; root:xnu-1228.15.4~1/RELEASE_I386 i386 BOOST_LIB_VERSION=1_40Mon Apr 9 12:56:02 [initandlisten] options: {}Mon Apr 9 12:56:02 [initandlisten] journal dir=/data/db/journalMon Apr 9 12:56:02 [initandlisten] recover : no journal files present, no recovery neededMon Apr 9 12:56:02 [websvr] admin web console waiting for connections on port 28017Mon Apr 9 12:56:02 [initandlisten] waiting for connections on port 27017 Check out the JPA/NoSQL sample from SVN repository. The complete source code built in this TOTD can be downloaded here. Create Java EE 6 web app Create a Java EE 6 Maven web app as: mvn archetype:generate -DarchetypeGroupId=org.codehaus.mojo.archetypes -DarchetypeArtifactId=webapp-javaee6 -DgroupId=model -DartifactId=javaee-nosql -DarchetypeVersion=1.5 -DinteractiveMode=false Copy the model files from the checked out workspace to the generated project as: cd javaee-nosqlcp -r ~/code/workspaces/org.eclipse.persistence.example.jpa.nosql.mongo/src/model src/main/java Copy "persistence.xml" mkdir src/main/resources cp -r ~/code/workspaces/org.eclipse.persistence.example.jpa.nosql.mongo/src/META-INF ./src/main/resources Add the following dependencies: <dependency> <groupId>org.eclipse.persistence</groupId> <artifactId>org.eclipse.persistence.jpa</artifactId> <version>2.4.0-SNAPSHOT</version> <scope>provided</scope></dependency><dependency> <groupId>org.eclipse.persistence</groupId> <artifactId>org.eclipse.persistence.nosql</artifactId> <version>2.4.0-SNAPSHOT</version></dependency><dependency> <groupId>org.mongodb</groupId> <artifactId>mongo-java-driver</artifactId> <version>2.7.3</version></dependency> The first one is for the EclipseLink latest APIs, the second one is for EclipseLink/NoSQL support, and the last one is the MongoDB Java driver. And the following repository: <repositories> <repository> <id>EclipseLink Repo</id> <url>http://www.eclipse.org/downloads/download.php?r=1&nf=1&file=/rt/eclipselink/maven.repo</url> <snapshots> <enabled>true</enabled> </snapshots> </repository> </repositories> Copy the "Test.java" to the generated project: mkdir src/main/java/examplecp -r ~/code/workspaces/org.eclipse.persistence.example.jpa.nosql.mongo/src/example/Test.java ./src/main/java/example/ This file contains the source code to CRUD the JPA entity to MongoDB. This sample is explained in detail on EclipseLink wiki. Create a new Servlet in "example" directory as: package example;import java.io.IOException;import java.io.PrintWriter;import javax.servlet.ServletException;import javax.servlet.annotation.WebServlet;import javax.servlet.http.HttpServlet;import javax.servlet.http.HttpServletRequest;import javax.servlet.http.HttpServletResponse;/** * @author Arun Gupta */@WebServlet(name = "TestServlet", urlPatterns = {"/TestServlet"})public class TestServlet extends HttpServlet { protected void processRequest(HttpServletRequest request, HttpServletResponse response) throws ServletException, IOException { response.setContentType("text/html;charset=UTF-8"); PrintWriter out = response.getWriter(); try { out.println("<html>"); out.println("<head>"); out.println("<title>Servlet TestServlet</title>"); out.println("</head>"); out.println("<body>"); out.println("<h1>Servlet TestServlet at " + request.getContextPath() + "</h1>"); try { Test.main(null); } catch (Exception ex) { ex.printStackTrace(); } out.println("</body>"); out.println("</html>"); } finally { out.close(); } } @Override protected void doGet(HttpServletRequest request, HttpServletResponse response) throws ServletException, IOException { processRequest(request, response); } @Override protected void doPost(HttpServletRequest request, HttpServletResponse response) throws ServletException, IOException { processRequest(request, response); }} Build the project and deploy it as: mvn clean packageglassfish3/bin/asadmin deploy --force=true target/javaee-nosql-1.0-SNAPSHOT.war Accessing http://localhost:8080/javaee-nosql/TestServlet shows the following messages in the server.log: connecting(EISLogin( platform=> MongoPlatform user name=> "" MongoConnectionSpec())) . . .Connected: User: Database: 2.7 Version: 2.7 . . .Executing MappedInteraction() spec => null properties => {mongo.collection=CUSTOMER, mongo.operation=INSERT} input => [DatabaseRecord( CUSTOMER._id => 4F848E2BDA0670307E2A8FA4 CUSTOMER.NAME => AMCE)]. . .Data access result: [{TOTALCOST=757.0, ORDERLINES=[{DESCRIPTION=table, LINENUMBER=1, COST=300.0}, {DESCRIPTION=balls, LINENUMBER=2, COST=5.0}, {DESCRIPTION=rackets, LINENUMBER=3, COST=15.0}, {DESCRIPTION=net, LINENUMBER=4, COST=2.0}, {DESCRIPTION=shipping, LINENUMBER=5, COST=80.0}, {DESCRIPTION=handling, LINENUMBER=6, COST=55.0},{DESCRIPTION=tax, LINENUMBER=7, COST=300.0}], SHIPPINGADDRESS=[{POSTALCODE=L5J1H7, PROVINCE=ON, COUNTRY=Canada, CITY=Ottawa,STREET=17 Jane St.}], VERSION=2, _id=4F848E2BDA0670307E2A8FA8,DESCRIPTION=Pingpong table, CUSTOMER__id=4F848E2BDA0670307E2A8FA7, BILLINGADDRESS=[{POSTALCODE=L5J1H8, PROVINCE=ON, COUNTRY=Canada, CITY=Ottawa, STREET=7 Bank St.}]}] You'll not see any output in the browser, just the output in the console. But the code can be easily modified to do so. Once again, the complete Maven project can be downloaded here. Do you want to try accessing relational and non-relational (aka NoSQL) databases in the same PU ?

Read the article

Parallel LINQ - PLINQ

- by nmarun

Turns out now with .net 4.0 we can run a query like a multi-threaded application. Say you want to query a collection of objects and return only those that meet certain conditions. Until now, we basically had one ‘control’ that iterated over all the objects in the collection, checked the condition on each object and returned if it passed. We obviously agree that if we can ‘break’ this task into smaller ones, assign each task to a different ‘control’ and ask all the controls to do their job - in-parallel, the time taken the finish the entire task will be much lower. Welcome to PLINQ. Let’s take some examples. I have the following method that uses our good ol’ LINQ. 1: private static void Linq(int lowerLimit, int upperLimit) 2: { 3: // populate an array with int values from lowerLimit to the upperLimit 4: var source = Enumerable.Range(lowerLimit, upperLimit); 5: 6: // Start a timer 7: Stopwatch stopwatch = new Stopwatch(); 8: stopwatch.Start(); 9: 10: // set the expectation => build the expression tree 11: var evenNumbers = from num in source 12: where IsDivisibleBy(num, 2) 13: select num; 14: 15: // iterate over and print the returned items 16: foreach (var number in evenNumbers) 17: { 18: Console.WriteLine(string.Format("** {0}", number)); 19: } 20: 21: stopwatch.Stop(); 22: 23: // check the metrics 24: Console.WriteLine(String.Format("Elapsed {0}ms", stopwatch.ElapsedMilliseconds)); 25: } I’ve added comments for the major steps, but the only thing I want to talk about here is the IsDivisibleBy() method. I know I could have just included the logic directly in the where clause. I called a method to add ‘delay’ to the execution of the query - to simulate a loooooooooong operation (will be easier to compare the results). 1: private static bool IsDivisibleBy(int number, int divisor) 2: { 3: // iterate over some database query 4: // to add time to the execution of this method; 5: // the TableB has around 10 records 6: for (int i = 0; i < 10; i++) 7: { 8: DataClasses1DataContext dataContext = new DataClasses1DataContext(); 9: var query = from b in dataContext.TableBs select b; 10: 11: foreach (var row in query) 12: { 13: // Do NOTHING (wish my job was like this) 14: } 15: } 16: 17: return number % divisor == 0; 18: } Now, let’s look at how to modify this to PLINQ. 1: private static void Plinq(int lowerLimit, int upperLimit) 2: { 3: // populate an array with int values from lowerLimit to the upperLimit 4: var source = Enumerable.Range(lowerLimit, upperLimit); 5: 6: // Start a timer 7: Stopwatch stopwatch = new Stopwatch(); 8: stopwatch.Start(); 9: 10: // set the expectation => build the expression tree 11: var evenNumbers = from num in source.AsParallel() 12: where IsDivisibleBy(num, 2) 13: select num; 14: 15: // iterate over and print the returned items 16: foreach (var number in evenNumbers) 17: { 18: Console.WriteLine(string.Format("** {0}", number)); 19: } 20: 21: stopwatch.Stop(); 22: 23: // check the metrics 24: Console.WriteLine(String.Format("Elapsed {0}ms", stopwatch.ElapsedMilliseconds)); 25: } That’s it, this is now in PLINQ format. Oh and if you haven’t found the difference, look line 11 a little more closely. You’ll see an extension method ‘AsParallel()’ added to the ‘source’ variable. Couldn’t be more simpler right? So this is going to improve the performance for us. Let’s test it. So in my Main method of the Console application that I’m working on, I make a call to both. 1: static void Main(string[] args) 2: { 3: // set lower and upper limits 4: int lowerLimit = 1; 5: int upperLimit = 20; 6: // call the methods 7: Console.WriteLine("Calling Linq() method"); 8: Linq(lowerLimit, upperLimit); 9: 10: Console.WriteLine(); 11: Console.WriteLine("Calling Plinq() method"); 12: Plinq(lowerLimit, upperLimit); 13: 14: Console.ReadLine(); // just so I get enough time to read the output 15: } YMMV, but here are the results that I got: It’s quite obvious from the above results that the Plinq() method is taking considerably less time than the Linq() version. I’m sure you’ve already noticed that the output of the Plinq() method is not in order. That’s because, each of the ‘control’s we sent to fetch the results, reported with values as and when they obtained them. This is something about parallel LINQ that one needs to remember – the collection cannot be guaranteed to be undisturbed. This could be counted as a negative about PLINQ (emphasize ‘could’). Nevertheless, if we want the collection to be sorted, we can use a SortedSet (.net 4.0) or build our own custom ‘sorter’. Either way we go, there’s a good chance we’ll end up with a better performance using PLINQ. And there’s another negative of PLINQ (depending on how you see it). This is regarding the CPU cycles. See the usage for Linq() method (used ResourceMonitor): I have dual CPU’s and see the height of the peak in the bottom two blocks and now compare to what happens when I run the Plinq() method. The difference is obvious. Higher usage, but for a shorter duration (width of the peak). Both these points make sense in both cases. Linq() runs for a longer time, but uses less resources whereas Plinq() runs for a shorter time and consumes more resources. Even after knowing all these, I’m still inclined towards PLINQ. PLINQ rocks! (no hard feelings LINQ)

Read the article

DTracing a PHPUnit Test: Looking at Functional Programming

- by cj

Here's a quick example of using DTrace Dynamic Tracing to work out what a PHP code base does. I was reading the article Functional Programming in PHP by Patkos Csaba and wondering how efficient this stype of programming is. I thought this would be a good time to fire up DTrace and see what is going on. Since DTrace is "always available" even in production machines (once PHP is compiled with --enable-dtrace), this was easy to do. I have Oracle Linux with the UEK3 kernel and PHP 5.5 with DTrace static probes enabled, as described in DTrace PHP Using Oracle Linux 'playground' Pre-Built Packages I installed the Functional Programming sample code and Sebastian Bergmann's PHPUnit. Although PHPUnit is included in the Functional Programming example, I found it easier to separately download and use its phar file: cd ~/Desktop wget -O master.zip https://github.com/tutsplus/functional-programming-in-php/archive/master.zip wget https://phar.phpunit.de/phpunit.phar unzip master.zip I created a DTrace D script functree.d: #pragma D option quiet self int indent; BEGIN { topfunc = $1; } php$target:::function-entry /copyinstr(arg0) == topfunc/ { self->follow = 1; } php$target:::function-entry /self->follow/ { self->indent += 2; printf("%*s %s%s%s\n", self->indent, "->", arg3?copyinstr(arg3):"", arg4?copyinstr(arg4):"", copyinstr(arg0)); } php$target:::function-return /self->follow/ { printf("%*s %s%s%s\n", self->indent, "<-", arg3?copyinstr(arg3):"", arg4?copyinstr(arg4):"", copyinstr(arg0)); self->indent -= 2; } php$target:::function-return /copyinstr(arg0) == topfunc/ { self->follow = 0; } This prints a PHP script function call tree starting from a given PHP function name. This name is passed as a parameter to DTrace, and assigned to the variable topfunc when the DTrace script starts. With this D script, choose a PHP function that isn't recursive, or modify the script to set self->follow = 0 only when all calls to that function have unwound. From looking at the sample FunSets.php code and its PHPUnit test driver FunSetsTest.php, I settled on one test function to trace: function testUnionContainsAllElements() { ... } I invoked DTrace to trace function calls invoked by this test with # dtrace -s ./functree.d -c 'php phpunit.phar \ /home/cjones/Desktop/functional-programming-in-php-master/FunSets/Tests/FunSetsTest.php' \ '"testUnionContainsAllElements"' The core of this command is a call to PHP to run PHPUnit on the FunSetsTest.php script. Outside that, DTrace is called and the PID of PHP is passed to the D script $target variable so the probes fire just for this invocation of PHP. Note the quoting around the PHP function name passed to DTrace. The parameter must have double quotes included so DTrace knows it is a string. The output is: PHPUnit 3.7.28 by Sebastian Bergmann. ......-> FunSetsTest::testUnionContainsAllElements -> FunSets::singletonSet <- FunSets::singletonSet -> FunSets::singletonSet <- FunSets::singletonSet -> FunSets::union <- FunSets::union -> FunSets::contains -> FunSets::{closure} -> FunSets::contains -> FunSets::{closure} <- FunSets::{closure} <- FunSets::contains <- FunSets::{closure} <- FunSets::contains -> PHPUnit_Framework_Assert::assertTrue -> PHPUnit_Framework_Assert::isTrue <- PHPUnit_Framework_Assert::isTrue -> PHPUnit_Framework_Assert::assertThat -> PHPUnit_Framework_Constraint::count <- PHPUnit_Framework_Constraint::count -> PHPUnit_Framework_Constraint::evaluate -> PHPUnit_Framework_Constraint_IsTrue::matches <- PHPUnit_Framework_Constraint_IsTrue::matches <- PHPUnit_Framework_Constraint::evaluate <- PHPUnit_Framework_Assert::assertThat <- PHPUnit_Framework_Assert::assertTrue -> FunSets::contains -> FunSets::{closure} -> FunSets::contains -> FunSets::{closure} <- FunSets::{closure} <- FunSets::contains -> FunSets::contains -> FunSets::{closure} <- FunSets::{closure} <- FunSets::contains <- FunSets::{closure} <- FunSets::contains -> PHPUnit_Framework_Assert::assertTrue -> PHPUnit_Framework_Assert::isTrue <- PHPUnit_Framework_Assert::isTrue -> PHPUnit_Framework_Assert::assertThat -> PHPUnit_Framework_Constraint::count <- PHPUnit_Framework_Constraint::count -> PHPUnit_Framework_Constraint::evaluate -> PHPUnit_Framework_Constraint_IsTrue::matches <- PHPUnit_Framework_Constraint_IsTrue::matches <- PHPUnit_Framework_Constraint::evaluate <- PHPUnit_Framework_Assert::assertThat <- PHPUnit_Framework_Assert::assertTrue -> FunSets::contains -> FunSets::{closure} -> FunSets::contains -> FunSets::{closure} <- FunSets::{closure} <- FunSets::contains -> FunSets::contains -> FunSets::{closure} <- FunSets::{closure} <- FunSets::contains <- FunSets::{closure} <- FunSets::contains -> PHPUnit_Framework_Assert::assertFalse -> PHPUnit_Framework_Assert::isFalse -> {closure} -> main <- main <- {closure} <- PHPUnit_Framework_Assert::isFalse -> PHPUnit_Framework_Assert::assertThat -> PHPUnit_Framework_Constraint::count <- PHPUnit_Framework_Constraint::count -> PHPUnit_Framework_Constraint::evaluate -> PHPUnit_Framework_Constraint_IsFalse::matches <- PHPUnit_Framework_Constraint_IsFalse::matches <- PHPUnit_Framework_Constraint::evaluate <- PHPUnit_Framework_Assert::assertThat <- PHPUnit_Framework_Assert::assertFalse <- FunSetsTest::testUnionContainsAllElements ... Time: 1.85 seconds, Memory: 3.75Mb OK (9 tests, 23 assertions) The periods correspond to the successful tests before and after (and from) the test I was tracing. You can see the function entry ("->") and return ("<-") points. Cross checking with the testUnionContainsAllElements() source code confirms the two singletonSet() calls, one union() call, two assertTrue() calls and finally an assertFalse() call. These assertions have a contains() call as a parameter, so contains() is called before the PHPUnit assertion functions are run. You can see contains() being called recursively, and how the closures are invoked. If you want to focus on the application logic and suppress the PHPUnit function trace, you could turn off tracing when assertions are being checked by adding D clauses checking the entry and exit of assertFalse() and assertTrue(). But if you want to see all of PHPUnit's code flow, you can modify the functree.d code that sets and unsets self-follow, and instead change it to toggle the variable in request-startup and request-shutdown probes: php$target:::request-startup { self->follow = 1 } php$target:::request-shutdown { self->follow = 0 } Be prepared for a large amount of output!

Read the article

Handling HumanTask attachments in Oracle BPM 11g PS4FP+ (I)

- by ccasares

Adding attachments to a HumanTask is a feature that exists in Oracle HWF (Human Workflow) since 10g. However, in 11g there have been many improvements on this feature and this entry will try to summarize them. Oracle BPM 11g 11.1.1.5.1 (aka PS4 Feature Pack or PS4FP) introduced two great features: Ability to link attachments at a Task scope or at a Process scope: "Task" attachments are only visible within the scope (lifetime) of a task. This means that, initially, any member of the assignment pattern of the Human Task will be able to handle (add, review or remove) attachments. However, once the task is completed, subsequent human tasks will not have access to them. This does not mean those attachments got lost. Once the human task is completed, attachments can be retrieved in order to, i.e., check them in to a Content Server or to inject them to a new and different human task. Aside note: a "re-initiated" human task will inherit comments and attachments, along with history and -optionally- payload. See here for more info. "Process" attachments are visible within the scope of the process. This means that subsequent human tasks in the same process instance will have access to them. Ability to use Oracle WebCenter Content (previously known as "Oracle UCM") as the backend for the attachments instead of using HWF database backend. This feature adds all content server document lifecycle capabilities to HWF attachments (versioning, RBAC, metadata management, etc). As of today, only Oracle WCC is supported. However, Oracle BPM Suite does include a license of Oracle WCC for the solely usage of document management within BPM scope. Here are some code samples that leverage the above features. Retrieving uploaded attachments -Non UCM- Non UCM attachments (default ones or those that have existed from 10g, and are stored "as-is" in HWK database backend) can be retrieved after the completion of the Human Task. Firstly, we need to know whether any attachment has been effectively uploaded to the human task. There are two ways to find it out: Through an XPath function: Checking the execData/attachment[] structure. For example: Once we are sure one ore more attachments were uploaded to the Human Task, we want to get them. In this example, by "get" I mean to get the attachment name and the payload of the file. Aside note: Oracle HWF lets you to upload two kind of [non-UCM] attachments: a desktop document and a Web URL. This example focuses just on the desktop document one. In order to "retrieve" an uploaded Web URL, you can get it directly from the execData/attachment[] structure. Attachment content (payload) is retrieved through the getTaskAttachmentContents() XPath function: This example shows how to retrieve as many attachments as those had been uploaded to the Human Task and write them to the server using the File Adapter service. The sample process excerpt is as follows: A dummy UserTask using "HumanTask1" Human Task followed by a Embedded Subprocess that will retrieve the attachments (we're assuming at least one attachment is uploaded): and once retrieved, we will write each of them back to a file in the server using a File Adapter service: In detail: We've defined an XSD structure that will hold the attachments (both name and payload): Then, we can create a BusinessObject based on such element (attachmentCollection) and create a variable (named attachmentBPM) of such BusinessObject type. We will also need to keep a copy of the HumanTask output's execData structure. Therefore we need to create a variable of type TaskExecutionData... ...and copy the HumanTask output execData to it: Now we get into the embedded subprocess that will retrieve the attachments' payload. First, and using an XSLT transformation, we feed the attachmentBPM variable with the name of each attachment and setting an empty value to the payload: Please note that we're using the XSLT for-each node to create as many target structures as necessary. Also note that we're setting an Empty text to the payload variable. The reason for this is to make sure the <payload></payload> tag gets created. This is needed when we map the payload to the XML variable later. Aside note: We are assuming that we're retrieving non-UCM attachments. However in real life you might want to check the type of attachment you're handling. The execData/attachment[]/storageType contains the values "UCM" for UCM type attachments, "TASK" for non-UCM ones or "URL" for Web URL ones. Those values are part of the "Ext.Com.Oracle.Xmlns.Bpel.Workflow.Task.StorageTypeEnum" enumeration. Once we have fed the attachmentsBPM structure and so it now contains the name of each of the attachments, it is time to iterate through it and get the payload. Therefore we will use a new embedded subprocess of type MultiInstance, that will iterate over the attachmentsBPM/attachment[] element: In every iteration we will use a Script activity to map the corresponding payload element with the result of the XPath function getTaskAttachmentContents(). Please, note how the target array element is indexed with the loopCounter predefined variable, so that we make sure we're feeding the right element during the array iteration: The XPath function used looks as follows: hwf:getTaskAttachmentContents(bpmn:getDataObject('UserTask1LocalExecData')/ns1:systemAttributes/ns1:taskId, bpmn:getDataObject('attachmentsBPM')/ns:attachment[bpmn:getActivityInstanceAttribute('SUBPROCESS3067107484296', 'loopCounter')]/ns:fileName) where the input parameters are: taskId of the just completed Human Task attachment name we're retrieving the payload from array index (loopCounter predefined variable) Aside note: The reason whereby we're iterating the execData/attachment[] structure through embedded subprocess and not, i.e., using XSLT and for-each nodes, is mostly because the getTaskAttachmentContents() XPath function is currently not available in XSLT mappings. So all this example might be considered as a workaround until this gets fixed/enhanced in future releases. Once this embedded subprocess ends, we will have all attachments (name + payload) in the attachmentsBPM variable, which is the main goal of this sample. But in order to test everything runs fine, we finish the sample writing each attachment to a file. To that end we include a final embedded subprocess to concurrently iterate through each attachmentsBPM/attachment[] element: On each iteration we will use a Service activity that invokes a File Adapter write service. In here we have two important parameters to set. First, the payload itself. The file adapter awaits binary data in base64 format (string). We have to map it using XPath (Simple mapping doesn't recognize a String as a base64-binary valid target): Second, we must set the target filename using the Service Properties dialog box: Again, note how we're making use of the loopCounter index variable to get the right element within the embedded subprocess iteration. Handling UCM attachments will be part of a different and upcoming blog entry. Once I finish will all posts on this matter, I will upload the whole sample project to java.net.

Read the article

SQL SERVER – SSMS: Disk Usage Report

- by Pinal Dave

Let us start with humor! I think we the series on various reports, we come to a logical point. We covered all the reports at server level. This means the reports we saw were targeted towards activities that are related to instance level operations. These are mostly like how a doctor diagnoses a patient. At this point I am reminded of a dialog which I read somewhere: Patient: Doc, It hurts when I touch my head. Doc: Ok, go on. What else have you experienced? Patient: It hurts even when I touch my eye, it hurts when I touch my arms, it even hurts when I touch my feet, etc. Doc: Hmmm … Patient: I feel it hurts when I touch anywhere in my body. Doc: Ahh … now I get it. You need a plaster to your finger John. Sometimes the server level gives an indicator to what is happening in the system, but we need to get to the root cause for a specific database. So, this is the first blog in series where we would start discussing about database level reports. To launch database level reports, expand selected server in Object Explorer, expand the Databases folder, and then right-click any database for which we want to look at reports. From the menu, select Reports, then Standard Reports, and then any of database level reports. In this blog, we would talk about four “disk” reports because they are similar: Disk Usage Disk Usage by Top Tables Disk Usage by Table Disk Usage by Partition Disk Usage This report shows multiple information about the database. Let us discuss them one by one. We have divided the output into 5 different sections. Section 1 shows the high level summary of the database. It shows the space used by database files (mdf and ldf). Under the hood, the report uses, various DMVs and DBCC Commands, it is using sys.data_spaces and DBCC SHOWFILESTATS. Section 2 and 3 are pie charts. One for data file allocation and another for the transaction log file. Pie chart for “Data Files Space Usage (%)” shows space consumed data, indexes, allocated to the SQL Server database, and unallocated space which is allocated to the SQL Server database but not yet filled with anything. “Transaction Log Space Usage (%)” used DBCC SQLPERF (LOGSPACE) and shows how much empty space we have in the physical transaction log file. Section 4 shows the data from Default Trace and looks at Event IDs 92, 93, 94, 95 which are for “Data File Auto Grow”, “Log File Auto Grow”, “Data File Auto Shrink” and “Log File Auto Shrink” respectively. Here is an expanded view for that section. If default trace is not enabled, then this section would be replaced by the message “Trace Log is disabled” as highlighted below. Section 5 of the report uses DBCC SHOWFILESTATS to get information. Here is the enhanced version of that section. This shows the physical layout of the file. In case you have In-Memory Objects in the database (from SQL Server 2014), then report would show information about those as well. Here is the screenshot taken for a different database, which has In-Memory table. I have highlighted new things which are only shown for in-memory database. The new sections which are highlighted above are using sys.dm_db_xtp_checkpoint_files, sys.database_files and sys.data_spaces. The new type for in-memory OLTP is ‘FX’ in sys.data_space. The next set of reports is targeted to get information about a table and its storage. These reports can answer questions like: Which is the biggest table in the database? How many rows we have in table? Is there any table which has a lot of reserved space but its unused? Which partition of the table is having more data? Disk Usage by Top Tables This report provides detailed data on the utilization of disk space by top 1000 tables within the Database. The report does not provide data for memory optimized tables. Disk Usage by Table This report is same as earlier report with few difference. First Report shows only 1000 rows First Report does order by values in DMV sys.dm_db_partition_stats whereas second one does it based on name of the table. Both of the reports have interactive sort facility. We can click on any column header and change the sorting order of data. Disk Usage by Partition This report shows the distribution of the data in table based on partition in the table. This is so similar to previous output with the partition details now. Here is the query taken from profiler. SELECT row_number() OVER (ORDER BY a1.used_page_count DESC, a1.index_id) AS row_number , (dense_rank() OVER (ORDER BY a5.name, a2.name))%2 AS l1 , a1.OBJECT_ID , a5.name AS [schema] , a2.name , a1.index_id , a3.name AS index_name , a3.type_desc , a1.partition_number , a1.used_page_count * 8 AS total_used_pages , a1.reserved_page_count * 8 AS total_reserved_pages , a1.row_count FROM sys.dm_db_partition_stats a1 INNER JOIN sys.all_objects a2 ON ( a1.OBJECT_ID = a2.OBJECT_ID) AND a1.OBJECT_ID NOT IN (SELECT OBJECT_ID FROM sys.tables WHERE is_memory_optimized = 1) INNER JOIN sys.schemas a5 ON (a5.schema_id = a2.schema_id) LEFT OUTER JOIN sys.indexes a3 ON ( (a1.OBJECT_ID = a3.OBJECT_ID) AND (a1.index_id = a3.index_id) ) WHERE (SELECT MAX(DISTINCT partition_number) FROM sys.dm_db_partition_stats a4 WHERE (a4.OBJECT_ID = a1.OBJECT_ID)) >= 1 AND a2.TYPE <> N'S' AND a2.TYPE <> N'IT' ORDER BY a5.name ASC, a2.name ASC, a1.index_id, a1.used_page_count DESC, a1.partition_number Using all of the above reports, you should be able to get the usage of database files and also space used by tables. I think this is too much disk information for a single blog and I hope you have used them in the past to get data. Do let me know if you found anything interesting using these reports in your environments. Reference: Pinal Dave (http://blog.sqlauthority.com)Filed under: PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Server Management Studio, SQL Tips and Tricks, T SQL Tagged: SQL Reports

Read the article

SQL University: Database testing and refactoring tools and examples

- by Mladen Prajdic

This is a post for a great idea called SQL University started by Jorge Segarra also famously known as SqlChicken on Twitter. It’s a collection of blog posts on different database related topics contributed by several smart people all over the world. So this week is mine and we’ll be talking about database testing and refactoring. In 3 posts we’ll cover: SQLU part 1 - What and why of database testing SQLU part 2 - What and why of database refactoring SQLU part 3 - Database testing and refactoring tools and examples This is the third and last part of the series and in it we’ll take a look at tools we can test and refactor with plus some an example of the both. Tools of the trade First a few thoughts about how to go about testing a database. I'm firmily against any testing tools that go into the database itself or need an extra database. Unit tests for the database and applications using the database should all be in one place using the same technology. By using database specific frameworks we fragment our tests into many places and increase test system complexity. Let’s take a look at some testing tools. 1. NUnit, xUnit, MbUnit All three are .Net testing frameworks meant to unit test .Net application. But we can test databases with them just fine. I use NUnit because I’ve always used it for work and personal projects. One day this might change. So the thing to remember is to be flexible if something better comes along. All three are quite similar and you should be able to switch between them without much problem. 2. TSQLUnit As much as this framework is helpful for the non-C# savvy folks I don’t like it for the reason I stated above. It lives in the database and thus fragments the testing infrastructure. Also it appears that it’s not being actively developed anymore. 3. DbFit I haven’t had the pleasure of trying this tool just yet but it’s on my to-do list. From what I’ve read and heard Gojko Adzic (@gojkoadzic on Twitter) has done a remarkable job with it. 4. Redgate SQL Refactor and Apex SQL Refactor Neither of these refactoring tools are free, however if you have hardcore refactoring planned they are worth while looking into. I’ve only used the Red Gate’s Refactor and was quite impressed with it. 5. Reverting the database state I’ve talked before about ways to revert a database to pre-test state after unit testing. This still holds and I haven’t changed my mind. Also make sure to read the comments as they are quite informative. I especially like the idea of setting up and tearing down the schema for each test group with NHibernate. Testing and refactoring example We’ll take a look at the simple schema and data test for a view and refactoring the SELECT * in that view. We’ll use a single table PhoneNumbers with ID and Phone columns. Then we’ll refactor the Phone column into 3 columns Prefix, Number and Suffix. Lastly we’ll remove the original Phone column. Then we’ll check how the view behaves with tests in NUnit. The comments in code explain the problem so be sure to read them. I’m assuming you know NUnit and C#. T-SQL Code C# test code USE tempdbGOCREATE TABLE PhoneNumbers( ID INT IDENTITY(1,1), Phone VARCHAR(20))GOINSERT INTO PhoneNumbers(Phone)SELECT '111 222333 444' UNION ALLSELECT '555 666777 888'GO-- notice we don't have WITH SCHEMABINDINGCREATE VIEW vPhoneNumbersAS SELECT * FROM PhoneNumbersGO-- Let's take a look at what the view returns -- If we add a new columns and rows both tests will failSELECT *FROM vPhoneNumbers GO -- DoesViewReturnCorrectColumns test will SUCCEED -- DoesViewReturnCorrectData test will SUCCEED -- refactor to split Phone column into 3 partsALTER TABLE PhoneNumbers ADD Prefix VARCHAR(3)ALTER TABLE PhoneNumbers ADD Number VARCHAR(6)ALTER TABLE PhoneNumbers ADD Suffix VARCHAR(3)GO-- update the new columnsUPDATE PhoneNumbers SET Prefix = LEFT(Phone, 3), Number = SUBSTRING(Phone, 5, 6), Suffix = RIGHT(Phone, 3)GO-- remove the old columnALTER TABLE PhoneNumbers DROP COLUMN PhoneGO-- This returns unexpected results!-- it returns 2 columns ID and Phone even though -- we don't have a Phone column anymore.-- Notice that the data is from the Prefix column-- This is a danger of SELECT *SELECT *FROM vPhoneNumbers -- DoesViewReturnCorrectColumns test will SUCCEED -- DoesViewReturnCorrectData test will FAIL -- for a fix we have to call sp_refreshview -- to refresh the view definitionEXEC sp_refreshview 'vPhoneNumbers'-- after the refresh the view returns 4 columns-- this breaks the input/output behavior of the database-- which refactoring MUST NOT doSELECT *FROM vPhoneNumbers -- DoesViewReturnCorrectColumns test will FAIL -- DoesViewReturnCorrectData test will FAIL -- to fix the input/output behavior change problem -- we have to concat the 3 columns into one named PhoneALTER VIEW vPhoneNumbersASSELECT ID, Prefix + ' ' + Number + ' ' + Suffix AS PhoneFROM PhoneNumbersGO-- now it works as expectedSELECT *FROM vPhoneNumbers -- DoesViewReturnCorrectColumns test will SUCCEED -- DoesViewReturnCorrectData test will SUCCEED -- clean upDROP VIEW vPhoneNumbersDROP TABLE PhoneNumbers [Test]public void DoesViewReturnCoorectColumns(){ // conn is a valid SqlConnection to the server's tempdb // note the SET FMTONLY ON with which we return only schema and no data using (SqlCommand cmd = new SqlCommand("SET FMTONLY ON; SELECT * FROM vPhoneNumbers", conn)) { DataTable dt = new DataTable(); dt.Load(cmd.ExecuteReader(CommandBehavior.CloseConnection)); // test returned schema: number of columns, column names and data types Assert.AreEqual(dt.Columns.Count, 2); Assert.AreEqual(dt.Columns[0].Caption, "ID"); Assert.AreEqual(dt.Columns[0].DataType, typeof(int)); Assert.AreEqual(dt.Columns[1].Caption, "Phone"); Assert.AreEqual(dt.Columns[1].DataType, typeof(string)); }} [Test]public void DoesViewReturnCorrectData(){ // conn is a valid SqlConnection to the server's tempdb using (SqlCommand cmd = new SqlCommand("SELECT * FROM vPhoneNumbers", conn)) { DataTable dt = new DataTable(); dt.Load(cmd.ExecuteReader(CommandBehavior.CloseConnection)); // test returned data: number of rows and their values Assert.AreEqual(dt.Rows.Count, 2); Assert.AreEqual(dt.Rows[0]["ID"], 1); Assert.AreEqual(dt.Rows[0]["Phone"], "111 222333 444"); Assert.AreEqual(dt.Rows[1]["ID"], 2); Assert.AreEqual(dt.Rows[1]["Phone"], "555 666777 888"); }} With this simple example we’ve seen how a very simple schema can cause a lot of problems in the whole application/database system if it doesn’t have tests. Imagine what would happen if some outside process would depend on that view. It would get wrong data and propagate it silently throughout the system. And that is not good. So have tests at least for the crucial parts of your systems. And with that we conclude the Database Testing and Refactoring week at SQL University. Hope you learned something new and enjoy the learning weeks to come. Have fun!

Read the article

C#: Does an IDisposable in a Halted Iterator Dispose?

- by James Michael Hare

If that sounds confusing, let me give you an example. Let's say you expose a method to read a database of products, and instead of returning a List<Product> you return an IEnumerable<Product> in iterator form (yield return). This accomplishes several good things: The IDataReader is not passed out of the Data Access Layer which prevents abstraction leak and resource leak potentials. You don't need to construct a full List<Product> in memory (which could be very big) if you just want to forward iterate once. If you only want to consume up to a certain point in the list, you won't incur the database cost of looking up the other items. This could give us an example like: 1: // a sample data access object class to do standard CRUD operations. 2: public class ProductDao 3: { 4: private DbProviderFactory _factory = SqlClientFactory.Instance 5: 6: // a method that would retrieve all available products 7: public IEnumerable<Product> GetAvailableProducts() 8: { 9: // must create the connection 10: using (var con = _factory.CreateConnection()) 11: { 12: con.ConnectionString = _productsConnectionString; 13: con.Open(); 14: 15: // create the command 16: using (var cmd = _factory.CreateCommand()) 17: { 18: cmd.Connection = con; 19: cmd.CommandText = _getAllProductsStoredProc; 20: cmd.CommandType = CommandType.StoredProcedure; 21: 22: // get a reader and pass back all results 23: using (var reader = cmd.ExecuteReader()) 24: { 25: while(reader.Read()) 26: { 27: yield return new Product 28: { 29: Name = reader["product_name"].ToString(), 30: ... 31: }; 32: } 33: } 34: } 35: } 36: } 37: } The database details themselves are irrelevant. I will say, though, that I'm a big fan of using the System.Data.Common classes instead of your provider specific counterparts directly (SqlCommand, OracleCommand, etc). This lets you mock your data sources easily in unit testing and also allows you to swap out your provider in one line of code. In fact, one of the shared components I'm most proud of implementing was our group's DatabaseUtility library that simplifies all the database access above into one line of code in a thread-safe and provider-neutral way. I went with my own flavor instead of the EL due to the fact I didn't want to force internal company consumers to use the EL if they didn't want to, and it made it easy to allow them to mock their database for unit testing by providing a MockCommand, MockConnection, etc that followed the System.Data.Common model. One of these days I'll blog on that if anyone's interested. Regardless, you often have situations like the above where you are consuming and iterating through a resource that must be closed once you are finished iterating. For the reasons stated above, I didn't want to return IDataReader (that would force them to remember to Dispose it), and I didn't want to return List<Product> (that would force them to hold all products in memory) -- but the first time I wrote this, I was worried. What if you never consume the last item and exit the loop? Are the reader, command, and connection all disposed correctly? Of course, I was 99.999999% sure the creators of C# had already thought of this and taken care of it, but inspection in Reflector was difficult due to the nature of the state machines yield return generates, so I decided to try a quick example program to verify whether or not Dispose() will be called when an iterator is broken from outside the iterator itself -- i.e. before the iterator reports there are no more items. So I wrote a quick Sequencer class with a Dispose() method and an iterator for it. Yes, it is COMPLETELY contrived: 1: // A disposable sequence of int -- yes this is completely contrived... 2: internal class Sequencer : IDisposable 3: { 4: private int _i = 0; 5: private readonly object _mutex = new object(); 6: 7: // Constructs an int sequence. 8: public Sequencer(int start) 9: { 10: _i = start; 11: } 12: 13: // Gets the next integer 14: public int GetNext() 15: { 16: lock (_mutex) 17: { 18: return _i++; 19: } 20: } 21: 22: // Dispose the sequence of integers. 23: public void Dispose() 24: { 25: // force output immediately (flush the buffer) 26: Console.WriteLine("Disposed with last sequence number of {0}!", _i); 27: Console.Out.Flush(); 28: } 29: } And then I created a generator (infinite-loop iterator) that did the using block for auto-Disposal: 1: // simply defines an extension method off of an int to start a sequence 2: public static class SequencerExtensions 3: { 4: // generates an infinite sequence starting at the specified number 5: public static IEnumerable<int> GetSequence(this int starter) 6: { 7: // note the using here, will call Dispose() when block terminated. 8: using (var seq = new Sequencer(starter)) 9: { 10: // infinite loop on this generator, means must be bounded by caller! 11: while(true) 12: { 13: yield return seq.GetNext(); 14: } 15: } 16: } 17: } This is really the same conundrum as the database problem originally posed. Here we are using iteration (yield return) over a large collection (infinite sequence of integers). If we cut the sequence short by breaking iteration, will that using block exit and hence, Dispose be called? Well, let's see: 1: // The test program class 2: public class IteratorTest 3: { 4: // The main test method. 5: public static void Main() 6: { 7: Console.WriteLine("Going to consume 10 of infinite items"); 8: Console.Out.Flush(); 9: 10: foreach(var i in 0.GetSequence()) 11: { 12: // could use TakeWhile, but wanted to output right at break... 13: if(i >= 10) 14: { 15: Console.WriteLine("Breaking now!"); 16: Console.Out.Flush(); 17: break; 18: } 19: 20: Console.WriteLine(i); 21: Console.Out.Flush(); 22: } 23: 24: Console.WriteLine("Done with loop."); 25: Console.Out.Flush(); 26: } 27: } So, what do we see? Do we see the "Disposed" message from our dispose, or did the Dispose get skipped because from an "eyeball" perspective we should be locked in that infinite generator loop? Here's the results: 1: Going to consume 10 of infinite items 2: 0 3: 1 4: 2 5: 3 6: 4 7: 5 8: 6 9: 7 10: 8 11: 9 12: Breaking now! 13: Disposed with last sequence number of 11! 14: Done with loop. Yes indeed, when we break the loop, the state machine that C# generates for yield iterate exits the iteration through the using blocks and auto-disposes the IDisposable correctly. I must admit, though, the first time I wrote one, I began to wonder and that led to this test. If you've never seen iterators before (I wrote a previous entry here) the infinite loop may throw you, but you have to keep in mind it is not a linear piece of code, that every time you hit a "yield return" it cedes control back to the state machine generated for the iterator. And this state machine, I'm happy to say, is smart enough to clean up the using blocks correctly. I suspected those wily guys and gals at Microsoft engineered it well, and I wasn't disappointed. But, I've been bitten by assumptions before, so it's good to test and see. Yes, maybe you knew it would or figured it would, but isn't it nice to know? And as those campy 80s G.I. Joe cartoon public service reminders always taught us, "Knowing is half the battle...". Technorati Tags: C#,.NET

Read the article

Hard drive mounted at / , duplicate mounted hard drive after using MountManager

- by HellHarvest

possible duplicate post I'm running 12.04 64bit. My system is a dual boot for both Ubuntu and Windows7. Both operating systems are sharing the drive named "Elements". My volume named "Elements" is a 1TB SATA NTFS hard drive that shows up twice in the side bar in nautilus. One of the icons is functional and even has the convenient "eject" icon next to it. Below is a picture of the left menu in Nautilus, with System Monitor-File Systems tab open on top of it. Can someone advise me about how to get rid of this extra icon? I think the problem is much more deep-rooted than just a GUI glitch on Nautilus' part. The other icon does nothing but spit out the following error when I click on it (image below). This only happened AFTER I tried using Mount Manager to automate mounting the drive at start up. I've already uninstalled Mount Manager, and restarted, but the problem didn't go away. The hard drive does mount automatically now, so I guess that's cool. But now, every time I boot up now and open Nautilus, BOTH of these icons appear, one of which is fictitious and useless. According to the image above and the outputs of several other commands, it appears to be mounted at / In which case, no matter where I am in Nautilus when I try to click on that icon, of course it will tell me that that drive is in use by another program... Nautilus. I'm afraid of trying to unmount this hard drive (sdb6) because of where it appears to be mounted. I'm kind of a noob, and I have this gut feeling that tells me trying to unmount a drive at / will destroy my entire file system. This fear was further strengthened by the output of "$ fsck" at the very bottom of this post. Error immediately below when that 2nd "Elements" hard drive is clicked in Nautilus: Unable to mount Elements Mount is denied because the NTFS volume is already exclusively opened. The volume may be already mounted, or another software may use it which could be identified for example by the help of the 'fuser' command. It's odd to me that that error message above claims that it's an NTFS volume when everything else tell me that it's an ext4 volume. The actual hard drive "Elements" is in fact an NTFS volume. Here's the output of a few commands and configuration files that may be of interest: $ fuser -a / /: 2120r 2159rc 2160rc 2172r 2178rc 2180rc 2188r 2191rc 2200rc 2203rc 2205rc 2206r 2211r 2212r 2214r 2220r 2228r 2234rc 2246rc 2249rc 2254rc 2260rc 2261r 2262r 2277rc 2287rc 2291rc 2311rc 2313rc 2332rc 2334rc 2339rc 2343rc 2344rc 2352rc 2372rc 2389rc 2422r 2490r 2496rc 2501rc 2566r 2573rc 2581rc 2589rc 2592r 2603r 2611rc 2613rc 2615rc 2678rc 2927r 2981r 3104rc 4156rc 4196rc 4206rc 4213rc 4240rc 4297rc 5032rc 7609r 7613r 7648r 9593rc 18829r 18833r 19776r $ sudo df -h Filesystem Size Used Avail Use% Mounted on /dev/sdb6 496G 366G 106G 78% / udev 2.0G 4.0K 2.0G 1% /dev tmpfs 791M 1.5M 790M 1% /run none 5.0M 0 5.0M 0% /run/lock none 2.0G 672K 2.0G 1% /run/shm /dev/sda1 932G 312G 620G 34% /media/Elements /home/solderblob/.Private 496G 366G 106G 78% /home/solderblob /dev/sdb2 188G 100G 88G 54% /media/A2B24EACB24E852F /dev/sdb1 100M 25M 76M 25% /media/System Reserved $ sudo fdisk -l Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00093cab Device Boot Start End Blocks Id System /dev/sda1 2048 1953519615 976758784 7 HPFS/NTFS/exFAT Disk /dev/sdb: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders, total 1465149168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e8d9b Device Boot Start End Blocks Id System /dev/sdb1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sdb2 206848 392378768 196085960+ 7 HPFS/NTFS/exFAT /dev/sdb3 392380414 1465147391 536383489 5 Extended /dev/sdb5 1456762880 1465147391 4192256 82 Linux swap / Solaris /dev/sdb6 392380416 1448374271 527996928 83 Linux /dev/sdb7 1448376320 1456758783 4191232 82 Linux swap / Solaris Partition table entries are not in disk order $ cat /etc/fstab # <file system> <mount point> <type> <options> <dump> <pass> UUID=77039a2a-83d4-47a1-8a8c-a2ec4e4dfd0e / ext4 defaults 0 1 UUID=F6549CC4549C88CF /media/Elements ntfs-3g users 0 0 $ sudo blkid /dev/sda1: LABEL="Elements" UUID="F6549CC4549C88CF" TYPE="ntfs" /dev/sdb1: LABEL="System Reserved" UUID="5CDE130FDE12E156" TYPE="ntfs" /dev/sdb2: UUID="A2B24EACB24E852F" TYPE="ntfs" /dev/sdb6: UUID="77039a2a-83d4-47a1-8a8c-a2ec4e4dfd0e" TYPE="ext4" $ sudo blkid -c /dev/null (appears to be exactly the same as above) /dev/sda1: LABEL="Elements" UUID="F6549CC4549C88CF" TYPE="ntfs" /dev/sdb1: LABEL="System Reserved" UUID="5CDE130FDE12E156" TYPE="ntfs" /dev/sdb2: UUID="A2B24EACB24E852F" TYPE="ntfs" /dev/sdb6: UUID="77039a2a-83d4-47a1-8a8c-a2ec4e4dfd0e" TYPE="ext4" $ mount /dev/sdb6 on / type ext4 (rw) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) /dev/sda1 on /media/Elements type fuseblk (rw,noexec,nosuid,nodev,allow_other,blksize=4096) binfmt_misc on /proc/sys/fs/binfmt_misc type binfmt_misc (rw,noexec,nosuid,nodev) /home/solderblob/.Private on /home/solderblob type ecryptfs (ecryptfs_check_dev_ruid,ecryptfs_cipher=aes,ecryptfs_key_bytes=16,ecryptfs_unlink_sigs,ecryptfs_sig=76a47b0175afa48d,ecryptfs_fnek_sig=391b2d8b155215f7) gvfs-fuse-daemon on /home/solderblob/.gvfs type fuse.gvfs-fuse-daemon (rw,nosuid,nodev,user=solderblob) /dev/sdb2 on /media/A2B24EACB24E852F type fuseblk (rw,nosuid,nodev,allow_other,default_permissions,blksize=4096) /dev/sdb1 on /media/System Reserved type fuseblk (rw,nosuid,nodev,allow_other,default_permissions,blksize=4096) $ ls -a . A2B24EACB24E852F Ubuntu 12.04.1 LTS amd64 .. Elements System Reserved $ cat /proc/mounts rootfs / rootfs rw 0 0 sysfs /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0 proc /proc proc rw,nosuid,nodev,noexec,relatime 0 0 udev /dev devtmpfs rw,relatime,size=2013000k,nr_inodes=503250,mode=755 0 0 devpts /dev/pts devpts rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000 0 0 tmpfs /run tmpfs rw,nosuid,relatime,size=809872k,mode=755 0 0 /dev/disk/by-uuid/77039a2a-83d4-47a1-8a8c-a2ec4e4dfd0e / ext4 rw,relatime,user_xattr,acl,barrier=1,data=ordered 0 0 none /sys/fs/fuse/connections fusectl rw,relatime 0 0 none /sys/kernel/debug debugfs rw,relatime 0 0 none /sys/kernel/security securityfs rw,relatime 0 0 none /run/lock tmpfs rw,nosuid,nodev,noexec,relatime,size=5120k 0 0 none /run/shm tmpfs rw,nosuid,nodev,relatime 0 0 /dev/sda1 /media/Elements fuseblk rw,nosuid,nodev,noexec,relatime,user_id=0,group_id=0,allow_other,blksize=4096 0 0 binfmt_misc /proc/sys/fs/binfmt_misc binfmt_misc rw,nosuid,nodev,noexec,relatime 0 0 /home/solderblob/.Private /home/solderblob ecryptfs rw,relatime,ecryptfs_fnek_sig=391b2d8b155215f7,ecryptfs_sig=76a47b0175afa48d,ecryptfs_cipher=aes,ecryptfs_key_bytes=16,ecryptfs_unlink_sigs 0 0 gvfs-fuse-daemon /home/solderblob/.gvfs fuse.gvfs-fuse-daemon rw,nosuid,nodev,relatime,user_id=1000,group_id=1000 0 0 /dev/sdb2 /media/A2B24EACB24E852F fuseblk rw,nosuid,nodev,relatime,user_id=0,group_id=0,default_permissions,allow_other,blksize=4096 0 0 /dev/sdb1 /media/System\040Reserved fuseblk rw,nosuid,nodev,relatime,user_id=0,group_id=0,default_permissions,allow_other,blksize=4096 0 0 gvfs-fuse-daemon /root/.gvfs fuse.gvfs-fuse-daemon rw,nosuid,nodev,relatime,user_id=0,group_id=0 0 0 $ fsck fsck from util-linux 2.20.1 e2fsck 1.42 (29-Nov-2011) /dev/sdb6 is mounted. WARNING!!! The filesystem is mounted. If you continue you ***WILL*** cause ***SEVERE*** filesystem damage. Do you really want to continue<n>? no check aborted.

Read the article

No root file system is defined error after installation

- by LearnCode

I installed ubuntu through Wubi and once i rebooted I get no root file system defined error. here's the output of the boot_info_script.Could anyone point me out where the error is. Boot Info Script 0.60 from 17 May 2011 ============================= Boot Info Summary: =============================== => Windows is installed in the MBR of /dev/sda. => Windows is installed in the MBR of /dev/sdb. sda1: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows 7 Boot files: /bootmgr /Boot/BCD /Windows/System32/winload.exe /ntldr /ntdetect.com /wubildr /ubuntu/winboot/wubildr /wubildr.mbr /ubuntu/winboot/wubildr.mbr /ubuntu/disks/root.disk /ubuntu/disks/swap.disk sda1/Wubi: _____________________________________________________________________ File system: Boot sector type: Unknown Boot sector info: Mounting failed: mount: unknown filesystem type '' sda2: __________________________________________________________________________ File system: vfat Boot sector type: Unknown Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: /boot.ini /ntldr /NTDETECT.COM sdb1: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: ============================ Drive/Partition Info: ============================= Drive: sda _____________________________________________________________________ Disk /dev/sda: 160.0 GB, 160041885696 bytes 240 heads, 63 sectors/track, 20673 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sda1 * 63 301,250,879 301,250,817 7 NTFS / exFAT / HPFS /dev/sda2 301,250,943 312,575,759 11,324,817 c W95 FAT32 (LBA) GUID Partition Table detected, but does not seem to be used. Partition Start Sector End Sector # of Sectors System /dev/sda1 323,465,741,313,502,988275,962,973,585-323,465,465,350,529,402 - /dev/sda2 242,728,591,638,290,720578,721,383,108,845,578335,992,791,470,554,859 - /dev/sda3 1,827,498,311,425,204,2562,091,935,274,843,009,907264,436,963,417,805,652 - /dev/sda4 579,711,218,081,401,3572,006,665,459,744,645,1521,426,954,241,663,243,796 - /dev/sda11 270,286,346,402,038,1183,786,543,326,404,525,9543,516,256,980,002,487,837 - /dev/sda12 4,179,681,002,230,769,6684,179,389,374,010,033,387-291,628,220,736,280 - /dev/sda13 232,556,480,979,456,1311,160,152,593,793,119,235927,596,112,813,663,105 - /dev/sda14 98,342,784,050,266,9183,691,264,578,843,725,1953,592,921,794,793,458,278 - /dev/sda15 2,307,845,219,957,882,4961,850,841,032,955,276,350-457,004,187,002,606,145 - /dev/sda16 512,592,046,878,946,497368,458,231,024,779,444-144,133,815,854,167,052 - /dev/sda17 2,504,135,232,870,384,3923,665,087,872,719,320,8291,160,952,639,848,936,438 - /dev/sda18 3,783,181,605,270,691,304122,034,509,624,708,942-3,661,147,095,645,982,361 - /dev/sda19 3,519,661,520,275,829,5122,376,243,094,723,723,587-1,143,418,425,552,105,924 - /dev/sda20 3,867,920,076,859,0744,494,691,111,933,625,1044,490,823,191,856,766,031 - /dev/sda21 1,500,144,061,909,253,7612,511,182,033,846,676,3401,011,037,971,937,422,580 - /dev/sda22 13,035,625,499,900,0062,360,168,613,941,394,9472,347,132,988,441,494,942 - /dev/sda23 4,228,978,682,068,599,48813,159,423,631,648,263-4,215,819,258,436,951,224 - /dev/sda24 3,695,955,742,872,046,9084,561,928,726,501,845,776865,972,983,629,798,869 - /dev/sda25 1,297,460,286,683,948,0461,444,350,486,339,417,957146,890,199,655,469,912 - /dev/sda26 1,228,858,248,533,131,831 0-1,228,858,248,533,131,830 - /dev/sda121 3,189,184,846,146,487,1461,849,820,258,006,914,852-1,339,364,588,139,572,293 - /dev/sda122 1,226,215,547,991,800,578389,781,518,734,546,300-836,434,029,257,254,277 - /dev/sda123 3,851,660,168,574,583,4654,046,215,657,583,031,556194,555,489,008,448,092 - /dev/sda124 1,197,460,980,174,153,341699,103,965,005,093,246-498,357,015,169,060,094 - Drive: sdb _____________________________________________________________________ Disk /dev/sdb: 750.2 GB, 750153367552 bytes 255 heads, 63 sectors/track, 91200 cylinders, total 1465143296 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sdb1 2,048 1,465,143,295 1,465,141,248 7 NTFS / exFAT / HPFS "blkid" output: ________________________________________________________________ Device UUID TYPE LABEL /dev/loop0 iso9660 Ubuntu 11.04 amd64 /dev/loop1 squashfs /dev/sda1 E814B55B14B52E06 ntfs /dev/sda2 01CD-023B vfat HP_RECOVERY /dev/sdb1 7836F22A36F1E8D0 ntfs Elements ================================ Mount points: ================================= Device Mount_Point Type Options /dev/loop0 /cdrom iso9660 (ro,noatime) /dev/loop1 /rofs squashfs (ro,noatime) /dev/sdb1 /mnt fuseblk (rw,nosuid,nodev,allow_other,blksize=4096) ================================ sda2/boot.ini: ================================ -------------------------------------------------------------------------------- [boot loader] timeout=0 default=C:\CMDCONS\BOOTSECT.DAT [operating systems] multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows XP Professional" /fastdetect C:\CMDCONS\BOOTSECT.DAT="Microsoft Windows Recovery Console" /cmdcons -------------------------------------------------------------------------------- ======================== Unknown MBRs/Boot Sectors/etc: ======================== Unknown GPT Partiton Type c104043000e9b9040dff24b580010100 Unknown GPT Partiton Type 46313020746f20737461727420746865 Unknown GPT Partiton Type 65727920706172746974696f6e207761 Unknown GPT Partiton Type 727920706172746974696f6e0d0a0000 Unknown GPT Partiton Type 000f84e5f7668b162404e82804744066 Unknown GPT Partiton Type ce01e8dc038bfe66391624047505e8d9 Unknown GPT Partiton Type 0345086603f0e881030bd2740333d240 Unknown GPT Partiton Type bece01e8db0287fec645041266895508 Unknown GPT Partiton Type 01f60634010175078b363b01e854f5e8 Unknown GPT Partiton Type 313825740ffec03865107408fec03824 Unknown GPT Partiton Type 02f60634014074088bfdbece01e85101 Unknown GPT Partiton Type 263401f9e894f30f858ef4e8e201e8ec Unknown GPT Partiton Type f7e960f35245434f5645525966606633 Unknown GPT Partiton Type 660faf1e00106603dac3668b0e001066 Unknown GPT Partiton Type 8bfd386d04740583c710e2f6c36660c6 Unknown GPT Partiton Type 04ebf132c0b91000f3aac3bf0c04ebf3 Unknown GPT Partiton Type 02662bc1660fb71e0e02662bc366031e Unknown GPT Partiton Type f4b40ebb0700b901003c08751381ff25 Unknown GPT Partiton Type 534f465448494e4b90653f62011b0100 Unknown GPT Partiton Type 0b050900027777772e68702e636f6d00 Unknown GPT Partiton Type d441a0f5030003000ecb744a08bb3746 Unknown GPT Partiton Type f8579a116b4a7aa931cde97a4b9b5c09 Unknown GPT Partiton Type 7229990415b77c0a1970e7e824237a3a Unknown GPT Partiton Type afb6e34d6b4bd8c7c0eada19a9786cc3 Unknown BootLoader on sda1/Wubi 00000000 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 |0000000000000000| * 00000200 Unknown BootLoader on sda2 00000000 e9 a7 00 52 45 43 4f 56 45 52 59 00 02 08 20 00 |...RECOVERY... .| 00000010 02 00 00 00 00 f8 00 00 3f 00 f0 00 7f b9 f4 11 |........?.......| 00000020 8c cd ac 00 1e 2b 00 00 00 00 00 00 02 00 00 00 |.....+..........| 00000030 01 00 06 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| 00000040 80 00 29 3b 02 cd 01 20 20 20 20 20 20 20 20 20 |..);... | 00000050 20 20 46 41 54 33 32 20 20 20 8b d0 c1 e2 02 80 | FAT32 ......| 00000060 e6 01 66 c1 e8 07 66 3b 46 f8 74 2a 66 89 46 f8 |..f...f;F.t*f.F.| 00000070 66 03 46 f4 66 0f b6 5e 28 80 e3 0f 74 0f 3a 5e |f.F.f..^(...t.:^| 00000080 10 0f 83 90 00 66 0f af 5e 24 66 03 c3 bb e0 07 |.....f..^$f.....| 00000090 b9 01 00 e8 cf 00 8b da 66 8b 87 00 7e 66 25 ff |........f...~f%.| 000000a0 ff ff 0f 66 3d f8 ff ff 0f c3 33 c9 8e d9 8e c1 |...f=.....3.....| 000000b0 8e d1 66 bc f4 7b 00 00 bd 00 7c 66 0f b6 46 10 |..f..{....|f..F.| 000000c0 66 f7 66 24 66 0f b7 56 0e 66 03 56 1c 66 89 56 |f.f$f..V.f.V.f.V| 000000d0 f4 66 03 c2 66 89 46 fc 66 c7 46 f8 ff ff ff ff |.f..f.F.f.F.....| 000000e0 66 8b 46 2c 66 50 e8 af 00 bb 70 00 b9 01 00 e8 |f.F,fP....p.....| 000000f0 73 00 bf 00 07 b1 0b be a9 7d f3 a6 74 2a 03 f9 |s........}..t*..| 00000100 83 c7 15 81 ff 00 09 72 ec 66 40 4a 75 db 66 58 |[email protected]| 00000110 e8 47 ff 72 cf be b4 7d ac 84 c0 74 09 b4 0e bb |.G.r...}...t....| 00000120 07 00 cd 10 eb f2 cd 19 66 58 ff 75 09 ff 75 0f |........fX.u..u.| 00000130 66 58 bb 00 20 66 83 f8 02 72 da 66 3d f8 ff ff |fX.. f...r.f=...| 00000140 0f 73 d2 66 50 e8 50 00 0f b6 4e 0d e8 16 00 c1 |.s.fP.P...N.....| 00000150 e1 05 03 d9 66 58 53 e8 00 ff 5b 72 d8 8a 56 40 |....fXS...[r..V@| 00000160 ea 00 00 00 20 66 60 66 6a 00 66 50 53 6a 00 66 |.... f`fj.fPSj.f| 00000170 68 10 00 01 00 8b f4 b8 00 42 8a 56 40 cd 13 be |h........B.V@...| 00000180 c7 7d 72 94 67 83 44 24 06 20 66 67 ff 44 24 08 |.}r.g.D$. fg.D$.| 00000190 e2 e3 83 c4 10 66 61 c3 66 48 66 48 66 0f b6 56 |.....fa.fHfHf..V| 000001a0 0d 66 f7 e2 66 03 46 fc c3 4e 54 4c 44 52 20 20 |.f..f.F..NTLDR | 000001b0 20 20 20 20 0d 0a 4e 6f 20 53 79 73 74 65 6d 20 | ..No System | 000001c0 44 69 73 6b 20 6f 72 0d 0a 44 69 73 6b 20 49 2f |Disk or..Disk I/| 000001d0 4f 20 65 72 72 6f 72 0d 0a 50 72 65 73 73 20 61 |O error..Press a| 000001e0 20 6b 65 79 20 74 6f 20 72 65 73 74 61 72 74 0d | key to restart.| 000001f0 0a 00 00 00 00 00 00 00 00 00 00 00 00 00 55 aa |..............U.| 00000200 =============================== StdErr Messages: =============================== umount: /isodevice: device is busy. (In some cases useful info about processes that use the device is found by lsof(8) or fuser(1))

Read the article

Unable to enable wireless on a Vostro 2520

- by Joe

I have a Vostro 2520 and not sure how to enable wireless on my machine. The details are given below, would appreciate any pointers to resolving this issue. lsmod returns Module Size Used by ath9k 132390 0 ath9k_common 14053 1 ath9k ath9k_hw 411151 2 ath9k,ath9k_common ath 24067 3 ath9k,ath9k_common,ath9k_hw b43 365785 0 mac80211 506816 2 ath9k,b43 cfg80211 205544 4 ath9k,ath,b43,mac80211 bcma 26696 1 b43 ssb 52752 1 b43 ndiswrapper 282628 0 ums_realtek 18248 0 usb_storage 49198 1 ums_realtek uas 18180 0 snd_hda_codec_hdmi 32474 1 snd_hda_codec_cirrus 24002 1 joydev 17693 0 parport_pc 32866 0 ppdev 17113 0 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep psmouse 97362 0 dell_wmi 12681 0 sparse_keymap 13890 1 dell_wmi snd_hda_intel 33773 3 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_cirrus,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq wmi 19256 1 dell_wmi snd 78855 16 snd_hda_codec_hdmi,snd_hda_codec_cirrus,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device mac_hid 13253 0 i915 473240 3 drm_kms_helper 46978 1 i915 uvcvideo 72627 0 drm 242038 4 i915,drm_kms_helper videodev 98259 1 uvcvideo soundcore 15091 1 snd dell_laptop 18119 0 dcdbas 14490 1 dell_laptop i2c_algo_bit 13423 1 i915 v4l2_compat_ioctl32 17128 1 videodev snd_page_alloc 18529 2 snd_hda_intel,snd_pcm video 19596 1 i915 serio_raw 13211 0 mei 41616 0 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62099 0 sudo lshw -class network *-network UNCLAIMED description: Network controller product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7c00000-f7c07fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 07 serial: 78:45:c4:a3:aa:65 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=192.168.1.5 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:e000(size=256) memory:f0004000-f0004fff memory:f0000000-f0003fff rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes 1: dell-bluetooth: Bluetooth Soft blocked: yes Hard blocked: yes Output of lspci > 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev > 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge > Graphics Controller (rev 09) 00:16.0 Communication controller: Intel > Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB > controller: Intel Corporation Panther Point USB Enhanced Host > Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther > Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: > Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) > 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root > Port 4 (rev c4) 00:1c.5 PCI bridge: Intel Corporation Panther Point > PCI Express Root Port 6 (rev c4) 00:1d.0 USB controller: Intel > Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) > 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller > (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 > port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel > Corporation Panther Point SMBus Controller (rev 04) 07:00.0 Network > controller: Broadcom Corporation Device 4365 (rev 01) 09:00.0 Ethernet > controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express > Gigabit Ethernet controller (rev 07) Output of lspci -v 0:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) Subsystem: Dell Device 0558 Flags: bus master, fast devsel, latency 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) (prog-if 00 [VGA controller]) Subsystem: Dell Device 0558 Flags: bus master, fast devsel, latency 0, IRQ 43 Memory at f7800000 (64-bit, non-prefetchable) [size=4M] Memory at e0000000 (64-bit, prefetchable) [size=256M] I/O ports at f000 [size=64] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: i915 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) Subsystem: Dell Device 0558 Flags: bus master, fast devsel, latency 0, IRQ 42 Memory at f7d0a000 (64-bit, non-prefetchable) [size=16] Capabilities: <access denied> Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) (prog-if 20 [EHCI]) Subsystem: Dell Device 0558 Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at f7d08000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) Subsystem: Dell Device 0558 Flags: bus master, fast devsel, latency 0, IRQ 44 Memory at f7d00000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=07, subordinate=07, sec-latency=0 Memory behind bridge: f7c00000-f7cfffff Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.5 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 6 (rev c4) (prog-if 00 [Normal decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=09, subordinate=09, sec-latency=0 I/O behind bridge: 0000e000-0000efff Prefetchable memory behind bridge: 00000000f0000000-00000000f00fffff Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) (prog-if 20 [EHCI]) Subsystem: Dell Device 0558 Flags: bus master, medium devsel, latency 0, IRQ 23 Memory at f7d07000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) Subsystem: Dell Device 0558 Flags: bus master, medium devsel, latency 0 Capabilities: <access denied> Kernel modules: iTCO_wdt 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) (prog-if 01 [AHCI 1.0]) Subsystem: Dell Device 0558 Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 40 I/O ports at f0b0 [size=8] I/O ports at f0a0 [size=4] I/O ports at f090 [size=8] I/O ports at f080 [size=4] I/O ports at f060 [size=32] Memory at f7d06000 (32-bit, non-prefetchable) [size=2K] Capabilities: <access denied> Kernel driver in use: ahci 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) Subsystem: Dell Device 0558 Flags: medium devsel, IRQ 11 Memory at f7d05000 (64-bit, non-prefetchable) [size=256] I/O ports at f040 [size=32] Kernel modules: i2c-i801 07:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) Subsystem: Dell Device 0016 Flags: bus master, fast devsel, latency 0, IRQ 10 Memory at f7c00000 (64-bit, non-prefetchable) [size=32K] Capabilities: <access denied> 09:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) Subsystem: Dell Device 0558 Flags: bus master, fast devsel, latency 0, IRQ 41 I/O ports at e000 [size=256] Memory at f0004000 (64-bit, prefetchable) [size=4K] Memory at f0000000 (64-bit, prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: r8169 Kernel modules: r8169

Read the article

xml file save/read error (making a highscore system for XNA game)

- by Eddy

i get an error after i write player name to the file for second or third time (An unhandled exception of type 'System.InvalidOperationException' occurred in System.Xml.dll Additional information: There is an error in XML document (18, 17).) (in highscores load method In data = (HighScoreData)serializer.Deserialize(stream); it stops) the problem is that some how it adds additional "" at the end of my .dat file could anyone tell me how to fix this? the file before save looks: <?xml version="1.0"?> <HighScoreData xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema"> <PlayerName> <string>neil</string> <string>shawn</string> <string>mark</string> <string>cindy</string> <string>sam</string> </PlayerName> <Score> <int>200</int> <int>180</int> <int>150</int> <int>100</int> <int>50</int> </Score> <Count>5</Count> </HighScoreData> the file after save looks: <?xml version="1.0"?> <HighScoreData xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema"> <PlayerName> <string>Nick</string> <string>Nick</string> <string>neil</string> <string>shawn</string> <string>mark</string> </PlayerName> <Score> <int>210</int> <int>210</int> <int>200</int> <int>180</int> <int>150</int> </Score> <Count>5</Count> </HighScoreData>> the part of my code that does all of save load to xml is: DECLARATIONS PART [Serializable] public struct HighScoreData { public string[] PlayerName; public int[] Score; public int Count; public HighScoreData(int count) { PlayerName = new string[count]; Score = new int[count]; Count = count; } } IAsyncResult result = null; bool inputName; HighScoreData data; int Score = 0; public string NAME; public string HighScoresFilename = "highscores.dat"; Game1 constructor public Game1() { graphics = new GraphicsDeviceManager(this); Content.RootDirectory = "Content"; Width = graphics.PreferredBackBufferWidth = 960; Height = graphics.PreferredBackBufferHeight =640; GamerServicesComponent GSC = new GamerServicesComponent(this); Components.Add(GSC); } Inicialize function (end of it) protected override void Initialize() { //other game code base.Initialize(); string fullpath =Path.Combine(HighScoresFilename); if (!File.Exists(fullpath)) { //If the file doesn't exist, make a fake one... // Create the data to save data = new HighScoreData(5); data.PlayerName[0] = "neil"; data.Score[0] = 200; data.PlayerName[1] = "shawn"; data.Score[1] = 180; data.PlayerName[2] = "mark"; data.Score[2] = 150; data.PlayerName[3] = "cindy"; data.Score[3] = 100; data.PlayerName[4] = "sam"; data.Score[4] = 50; SaveHighScores(data, HighScoresFilename); } } all methods for loading saving and output public static void SaveHighScores(HighScoreData data, string filename) { // Get the path of the save game string fullpath = Path.Combine("highscores.dat"); // Open the file, creating it if necessary FileStream stream = File.Open(fullpath, FileMode.OpenOrCreate); try { // Convert the object to XML data and put it in the stream XmlSerializer serializer = new XmlSerializer(typeof(HighScoreData)); serializer.Serialize(stream, data); } finally { // Close the file stream.Close(); } } /* Load highscores */ public static HighScoreData LoadHighScores(string filename) { HighScoreData data; // Get the path of the save game string fullpath = Path.Combine("highscores.dat"); // Open the file FileStream stream = File.Open(fullpath, FileMode.OpenOrCreate, FileAccess.Read); try { // Read the data from the file XmlSerializer serializer = new XmlSerializer(typeof(HighScoreData)); data = (HighScoreData)serializer.Deserialize(stream);//this is the line // where program gives an error } finally { // Close the file stream.Close(); } return (data); } /* Save player highscore when game ends */ private void SaveHighScore() { // Create the data to saved HighScoreData data = LoadHighScores(HighScoresFilename); int scoreIndex = -1; for (int i = 0; i < data.Count ; i++) { if (Score > data.Score[i]) { scoreIndex = i; break; } } if (scoreIndex > -1) { //New high score found ... do swaps for (int i = data.Count - 1; i > scoreIndex; i--) { data.PlayerName[i] = data.PlayerName[i - 1]; data.Score[i] = data.Score[i - 1]; } data.PlayerName[scoreIndex] = NAME; //Retrieve User Name Here data.Score[scoreIndex] = Score; // Retrieve score here SaveHighScores(data, HighScoresFilename); } } /* Iterate through data if highscore is called and make the string to be saved*/ public string makeHighScoreString() { // Create the data to save HighScoreData data2 = LoadHighScores(HighScoresFilename); // Create scoreBoardString string scoreBoardString = "Highscores:\n\n"; for (int i = 0; i<5;i++) { scoreBoardString = scoreBoardString + data2.PlayerName[i] + "-" + data2.Score[i] + "\n"; } return scoreBoardString; } when ill make this work i will start this code when i call game over (now i start it when i press some buttons, so i could test it faster) public void InputYourName() { if (result == null && !Guide.IsVisible) { string title = "Name"; string description = "Write your name in order to save your Score"; string defaultText = "Nick"; PlayerIndex playerIndex = new PlayerIndex(); result= Guide.BeginShowKeyboardInput(playerIndex, title, description, defaultText, null, null); // NAME = result.ToString(); } if (result != null && result.IsCompleted) { NAME = Guide.EndShowKeyboardInput(result); result = null; inputName = false; SaveHighScore(); } } this where i call output to the screen (ill call this in highscores meniu section when i am done with debugging) spriteBatch.DrawString(Font1, "" + makeHighScoreString(),new Vector2(500,200), Color.White); }

Search Results

Search found 19408 results on 777 pages for 'output formats'.

Page 392/777 | < Previous Page | 388 389 390 391 392 393 394 395 396 397 398 399 | Next Page >

- by AndrejaKo

- by devicerandom

- by asciiphil

- by Skip Huffman

- by user252098

- by NlightNFotis

- by dandelion

- by jsavit

- by Betaxpression

- by zowens

- by sreejukg

- by Wolter Hellmund

- by Bertrand Le Roy

- by Vincent Maverick Durano

- by arungupta

- by nmarun

- by cj

- by ccasares

- by Pinal Dave

- by Mladen Prajdic

- by James Michael Hare

- by HellHarvest

- by LearnCode

- by Joe

- by Eddy

< Previous Page | 388 389 390 391 392 393 394 395 396 397 398 399 | Next Page >