Search Results

Search found 21501 results on 861 pages for 'slow connection'.

Page 393/861 | < Previous Page | 389 390 391 392 393 394 395 396 397 398 399 400  | Next Page >

• Intel NIC X540-T1 non-functional in Ubuntu Server 12.04

  - by Jeff Carr

  I have installed three Intel X540-T1's in servers running Ubuntu Server 12.04, but all are non-functional, no link lights, no packets sent or received, and no connection on ip4 or ip6 whether set up as dhcp or static. Also, dmesg doesn't detect cable connection or disconnection. I updated the default ixgbe driver to Intel's latest version (3.11.33) with no change. The ethernet controller is being reported as X540-AT2 (which might be a problem that I can't figure out how to fix), but the subsystem is X540-T1 so I believe that might be intended. Does anyone have any experience with this that could assist? ifconfig eth2 eth2 Link encap:Ethernet HWaddr a0:36:9f:14:5f:ea inet addr:192.168.101.1 Bcast:192.168.101.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1<br> RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ethtool -i eth2 driver: ixgbe version: 3.11.33 firmware-version: 0x8000037c bus-info: 0000:08:00.0 supports-statistics: yes supports-test: yes supports-eeprom-access: yes supports-register-dump: yes lspci -vvnns 08:00.0 08:00.0 Ethernet controller [0200]: Intel Corporation Ethernet Controller 10 Gigabit X540-AT2 [8086:1528] (rev 01) Subsystem: Intel Corporation Ethernet Converged Network Adapter X540-T1 [8086:0002] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at e8000000 (64-bit, prefetchable) [size=2M] Region 4: Memory at e8200000 (64-bit, prefetchable) [size=16K] [virtual] Expansion ROM at e8280000 [disabled] [size=512K] Capabilities: <access denied> Kernel driver in use: ixgbe Kernel modules: ixgbe

  Read the article

• Why is SSH finding remote keys for other accounts?

  - by Brian Pontarelli

  This is a strange issue I'm having with SSH from my Macbook Pro to a Linux (Ubuntu 11.10) server. I have a DSA key setup on the remote Linux server under my home directory like this: /home/me/.ssh/authorzied_keys I also have the same DSA key setup for a few other accounts on the machine named "foo" and "bar". I can log into all of the accounts fine without any password. Therefore, the DSA keys are all setup correctly. The strange behavior I'm seeing is when debugging the SSH connection. During the connection, the SSH debug is outputting this: debug2: key: /Users/me/.ssh/id_dsa (0x7f91a1424220) debug2: key: /home/foo/.ssh/id_dsa (0x7f91a1425620) debug2: key: /home/bar/.ssh/id_rsa (0x7f91a1425c60) debug2: key: /Users/me/.ssh/id_rsa (0x0) This is strange for so many reasons, but essentially, why is SSH listing out keys on the server (/home/foo/.ssh/id_dsa and /home/bar/.ssh/id_rsa)? These files don't even exist on the server, so why are they listed? I'm not logging into the "foo" or "bar" accounts, so why is SSH even listing those? On my Macbook Pro, I only have a DSA key, but SSH is listing out an RSA key, what's that all about? Another user on the server doesn't get any of these messages when they log in and they have the exact same setup for their DSA key and the exact same Macbook Pro setup as mine? Does anyone know what these messages are and why SSH is outputting them?

  Read the article

• Is Gmail Being Blocked by my ISP (wait till you read this)?

  - by James

  This is the strangest thing I have ever encountered. I have a desktop on which I cannot access Gmail and also youtube sign in (I believe since youtube is owned by google they both use the same sign in system). So okay, maybe my ISP is blocking these for some reason or maybe my firewall is, or maybe there is something wrong with my connectivity, right? NO. On other computers that uses the same connection via a wireless router I can access both gmail and youtube sign in just fine. On this computer which doesn't have a wireless card and so I have to connect via Ethernet cable (connected to a USB converter since the Ethernet port doesn't work anymore) I can access all sites and services including things like aol and hotmail. But only when it comes to gmail, do I get complete and utter throttling. I even turned off my AV ad Firewall momentarily and no luck. The gmail ages starts to load and by mid point it just stays there loading and loading and loading... never ends. I tried everything, I reset the modem and router multiple times. I reinstalled my operating system from a vista to a windows 7 hoping a complete reinstall would solve the issue, but no luck. So can anyone for the life of them figure out why this could be? And yes, I am going to call my ISP but not to solve this issue, but to cancel them. I want to upgrade to cabel from DSL anyway. I didn't mention my ISP because I'm not sure if that is within the rules (if it's okay some one let me know and I will). P.S. All this happened one day, before gmail was perfectly accessible in this computer. I can't remember anything special that happened on that day prior to this. The only thing I can think of is, my ISP or Google itself is blocking this computer based on it's mac address, but I don't know if that's even done. Additional info: PC: Windows 7 Ultimate 32 bit Connection Type: DSL Connecting Medium: Ethernet cable via USB converter

  Read the article

• Windows 7 VPN Error 619

  - by TravisPUK

  So I am running Windows 7 Enterprise. This morning I was able to VPN using the built in VPN (Connect to Work Network etc). I had to change my network's IP address range and now the VPN will not work. It just stalls on the Verifying user name and password... message. But then it returns the 619 error. Anybody know why changing my machine's IP address would cause this problem? Where should I be looking to try and fix this issue? I have tried this on a Windows XP machine that also had the IP address range change and this still connects fine using exactly the same connection details. EDIT The internal network range changed from 192.x.x.x to 10.x.x.x. This was done on the entire Active Directory. All machines are running fine and the Windows XP machine, that works going to the same client VPN mentioned above is on the same network. Both the XP and the Win 7 machines are using DHCP served by the Domain Controller. The client domain is not performing any IP range checks/restrictions. The VPN is outside the internal network, connection is being made via the Internet and not passing through any other machine, other than the normal domain machines, ie DNS etc. This is passing through a router and the router has the relevant VPN passthrough options configured. All internal machines are working correctly with other forms of VPN, ie Cisco, Sonic etc (these were tested on other machines, they are not installed on the Vista or Win7 machines). After further testing, this is occurring on all Win7 and Vista machines where they can no longer connect to the client VPN, however all XP machines can still connect fine. This has been tested on three Vista, two Win7 and five XP machines. All machines are on DHCP and tests have been done with both the firewalls turned on and off, as well as with fixed IPs being used. Thanks Travis

  Read the article

• Wget save cookies not working

  - by TrymBeast

  I've been trying to login in the pyload through the web api, but wget is not saving the cookies and I don't understand why. I'm using the following command: wget --delete-after --keep-session-cookies --save-cookies=my_cookies.txt --post-data="username=USERNAME&password=PASSWORD" http://localhost:8000/api/login But the content of my_cookies.txt is: # HTTP cookie file. # Generated by Wget on 2012-06-23 22:31:33. # Edit at your own risk. When I run the same command but in debug mode I get the following output that includes the set cookie in the header response: DEBUG output created by Wget 1.10.2 (Red Hat modified) on linux-gnueabi. --22:31:11-- http://localhost:8000/api/login Resolving localhost... 127.0.0.1 Caching localhost => 127.0.0.1 Connecting to localhost|127.0.0.1|:8000... connected. Created socket 3. Releasing 0x000504d0 (new refcount 1). ---request begin--- POST /api/login HTTP/1.0 User-Agent: Wget/1.10.2 (Red Hat modified) Accept: */* Host: localhost:8000 Connection: Keep-Alive Content-Type: application/x-www-form-urlencoded Content-Length: 32 ---request end--- [POST data: username=USERNAME&password=PASSWORD] HTTP request sent, awaiting response... ---response begin--- HTTP/1.1 200 OK Content-Length: 34 Content-Type: application/json Cache-Control: no-cache, must-revalidate Set-cookie: beaker.session.id=405390ddc809efed54820638c95d7997; expires=Tue, 19-Jan-2038 04:14:07 GMT; Path=/ Connection: Keep-Alive Date: Sat, 23 Jun 2012 21:31:11 GMT Server: CherryPy/3.1.2 WSGI Server ---response end--- 200 OK hs->local_file is: login (not existing) Registered socket 3 for persistent reuse. TEXTHTML is on. Length: 34 [application/json] Saving to: `login' 100%[=======================================>] 34 --.-K/s in 0s 22:31:11 (1.28 MB/s) - `login' saved [34/34] Removing file due to --delete-after in main(): Removing login. Saving cookies to my_cookies.txt. Done saving cookies. Can anyone tell me what am I doing wrong? Thanks in advance!

  Read the article

• Migrating to CF9: trouble getting JRun working with SSL

  - by DaveBurns

  I have a client on MX7 who wants to migrate to CF9. I have a dev environment for them on my WinXP machine where I've configured MX7 to run with JRun's built-in web server. I've had that working for a long time with both regular and SSL connections. I installed CF9 yesterday side-by-side with the existing MX7 install to start testing. The install was smooth and detected MX7, adjusted CF9's port numbers for no conflict, etc. Testing started well: MX7 over regular and SSL still worked and CF9 worked over regular HTTP. But I can't get CF9 to work with SSL. I installed a new certificate with keytool, FireFox (v3.6) complained about it being unsigned, I added it to the exception list, and now I get this: Secure Connection Failed An error occurred during a connection to localhost:9101. Peer reports it experienced an internal error. (Error code: ssl_error_internal_error_alert) I've been Googling that in all variations but can't find much help to get past this. I don't see any info in any log files either. FWIW, here's my SSL config from SERVER-INF/jrun.xml: <service class="jrun.servlet.http.SSLService" name="SSLService"> <attribute name="enabled">true</attribute>` <attribute name="interface">*</attribute> <attribute name="port">9101</attribute> <attribute name="keyStore">{jrun.rootdir}/lib/mykey</attribute> <attribute name="keyStorePassword">*deleted*</attribute> <attribute name="trustStore">{jrun.rootdir}/lib/trustStore</attribute> <attribute name="socketFactoryName">jrun.servlet.http.JRunSSLServerSocketFactory</attribute> <attribute name="deactivated">false</attribute> <attribute name="bindAddress">*</attribute> <attribute name="clientAuth">false</attribute> </service> Anyone here know of any issues re setting up SSL and CF9? Anyone had success with it? Dave

  Read the article

• Sending emails with Thunderbird + Postfix + Zarafa does not work

  - by Sven Jung

  I installed zarafa on my vserver and use as MTA postfix. The webaccess works fine, I can revceive and send emails, also receiving mails with thunderbird (IMAP ssl/tls) works. But there is a problem, sending emails with thunderbird. I established an account in thunderbird with imap ssl/tls connection which works finde, and a starttls smtp connection on port 25 for the outgoing mail server. If I try to send an email with thunderbird I get an error: 5.7.1 Relay access denied this is my mail.log Sep 7 16:10:07 postfix/smtpd[6153]: connect from p4FE06C0A.dip.t-dialin.net[79.224.110.10] Sep 7 16:10:08 postfix/smtpd[6153]: NOQUEUE: reject: RCPT from p4FE06C0A.dip.t-dialin.net[79.224.110.10]: 554 5.7.1 <[email protected]>: Relay access denie$ Sep 7 16:10:10 postfix/smtpd[6153]: disconnect from p4FE06C0A.dip.t-dialin.net[79.224.110.10] and this my /etc/postfix/main.conf # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache virtual_mailbox_domains = firstdomain.de, seconddomain.de virtual_mailbox_maps = hash:/etc/postfix/virtual virtual_alias_maps = hash:/etc/postfix/virtual virtual_transport = lmtp:127.0.0.1:2003 myhostname = mail.firstdomain.de alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = localhost relayhost = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all inet_protocols = ipv4 I don't know what to do, because actually sending mails to internal and external addresses works with the webaccess. Perhaps somebody can help me?

  Read the article

• RRAS with DHCP when the IP pool is on a different subnet

  - by John B

  I run a small business network and the last couple of days I have been setting up some equipment to add VPN capabilities to our network. I've got the following set up: Windows 2008 R2 with RRAS - 172.22.200.50 Cisco RV082 router - 172.22.100.1 / 172.22.200.1 The Cisco router only support DHCP on a single class C network; 172.22.100.0/24. On the Cisco router I have set up an additional subnet; 172.22.200.0/24. The DHCP range is 172.22.100.200-254 When a PPTP connection comes in to the router, it is forwarded to my RRAS at 172.22.200.50. If I configure RRAS to assign IPs from a static pool on the 172.22.200.0/24 subnet everything works fine except the DNS suffix / search domain. However, if I set RRAS to use DHCP I am no longer able to contact any devices on the network. The IP I receive is on a different subnet (172.22.100.0/24). Is it possible to still use DHCP as the method of ip assignment in RRAS, even when the IP adresses assigned are in a different subnet? If yes, what piece of configuration am I missing to fix the VPN connection issues mentioned in the paragraph above. The reason I want RRAS with DHCP to work is because from what I have understood, this is the "only" way to hand out a DNS suffix to VPN clients. Any help on this matter is greatly appreciated!

  Read the article

• Performance of Cluster Shared Volume file copy from SAN

  - by Sequenzia

  I am hoping someone can help me out with a strange issue. We are running a Microsoft Failover Cluster with Server 2008 R2 and an Equallogic PS4000 SAN. Our main configuration has 2 Dell Poweredge T710 Servers in the cluster. We have CSV and Quorm setup. The servers each have 10 Broadcom 1Gb NICs. Right now 4 of the NICS are on the iSCSI network for accessing the SAN. They use MPIO and the Dell HIT pack. We have 5 VMs running on each node and everything runs smooth. No noticeable performance issues or anything. From the SAN I can see the 4 iSCSI connections from each server to each volume (CSV and Quorm). Again, it seems to perform great. The problem I am running into is with backups. I have tried a few backup programs like backupchain and Veeam. The problem is both of them are very very slow to backup the VMs. For instance I have a 500GB (fixed disc) VHD that’s running on the cluster. It takes over 18 hours to backup that VHD and that’s with compression and depuping turned off which is supposed to be the fasted. We also have a separate server that is just for backups. It has a lot of directed attached storage. As part of the troubleshooting I decided to bring that server into the cluster as a node. It now has access to the CSV and can read from C:\clusterstorage\volume1 which is where our VHDs live. This backup server only has 2 NICs. 1 NIC is going to the iSCSI network and the other is just on the main network. It has Intel NICS in it without any sort of MPIO or teaming. So with the 3rd server now in the cluster I started doing some benchmarking. I have a test VHD that’s about 7GBs that’s stored in the CSV. I have tested file copying that VHD from all 3 servers to directed attached storage in the respective server. The 2 Dell servers that are the main nodes in the cluster (they house the VMs) are reading that file at about 20Mbs/Sec. Which at that rate is way to slow for the backups. The other server which only has 1 NIC to the SAN is reading at around 100Mbs/Sec. I spent a few hours on the phone with Dell today about this . We went through all kind of tests and he was pretty dumb founded. He really has no idea why that server with only 1 NIC is reading about 5 times as fast as the servers with 4 NICS and MPIO. We looked at the network utilization of the NICs while the file copy was going on. The servers with the 4 NICs had a small increase of activity during the file copy but they only went up to around 8-10% on all 4 NICs. The other server with the 1 NIC jumped up to over 80% during the file copy. I plan on doing some more testing after hours and calling Dell back tomorrow but I really am confused (and so is Dell’s support rep) why I cannot get faster file copy access to the CSV on those servers. Anyone have any input on this? Any feedback would be greatly appreciated. Thanks in advance.

  Read the article

• ProFTPD / PAM issues with new centos/virtualmin install

  - by iamthewit

  Hi All, I just installed CentOS 5.4 on a rackspace cloud server and installed virtualmin which all seemed to go fine. The only problem I have is that I can not access the virtual servers directories via FTP. I get the following from filezilla: Status: Connecting to 1.1.1.1:21... Status: Connection established, waiting for welcome message... Response: 220 FTP Server ready. Command: USER username Response: 331 Password required for username. Command: PASS ******* Response: 230 User username logged in. Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is current directory. Command: TYPE I Response: 200 Type set to I Command: PASV Response: 227 Entering Passive Mode (1,1,1,1,216,214) Command: LIST Error: Connection timed out Error: Failed to retrieve directory listing and I get this from my /var/secure/log file Sep 22 19:40:42 stickeeserver proftpd: pam_unix(proftpd:session): session opened for user username by (uid=0) Sep 22 19:40:42 server proftpd[14051]: 94.136.40.82 (::ffff:217.207.31.60[::ffff:217.207.31.60]) - USER nastypasty: Login successful. Sep 22 19:40:42 server proftpd[14051]: 94.136.40.82 (::ffff:217.207.31.60[::ffff:217.207.31.60]) - Preparing to chroot to directory '/home/username' Sep 22 19:40:42 server proftpd[14051]: 94.136.40.82 (::ffff:217.207.31.60[::ffff:217.207.31.60]) - mod_delay/0.5: delaying for 728 usecs Sep 22 19:40:42 server proftpd[14051]: 94.136.40.82 (::ffff:217.207.31.60[::ffff:217.207.31.60]) - error setting IPV6_V6ONLY: Protocol not available Any help would be greatly appreciated, I'm not totally new to Linux but it's not my strongest subject. I do like to know exactly why problems occur though and how exactly to fix them so the more detail the better! cheers

  Read the article

• PHP include() through HTTP makes Apache time out

  - by Adam Interact

  I have a problem with ExpressionEngine2 after moving from an old server to WHM/cPanel running on CentOS6.4. Simple test code to reproduce that issue: <?php $protocol = strpos(strtolower($_SERVER['SERVER_PROTOCOL']),'https') === FALSE ? 'http' : 'https'; $host = $_SERVER['HTTP_HOST']; include($protocol . '://' . $host . '/header.html'); ?> <p> Main text...</p> <?php include($protocol . '://' . $host . '/footer.html'); ?> Where header.html looks like <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="http://www.w3.org/1999/xhtml"> <head> <meta http-equiv="Content-Type" content="text/html; charset=utf-8" /> <title>Untitled Document</title> </head> <body> and footer.html looks like: </body> </html> Creates Apache time out: Warning: include(http://www.domain.com/header.html) [function.include]: failed to open stream: Connection timed out in /home/domain/public_html/test/index.php on line 5 Warning: include() [function.include]: Failed opening 'http://www.domain.com/header.html' for inclusion (include_path='.:/usr/lib/php:/usr/local/lib/php') in /home/domain/public_html/test/index.php on line 5 Main text... Warning: include(http://www.domain.com/footer.html) [function.include]: failed to open stream: Connection timed out in /home/domain/public_html/test/index.php on line 12 Warning: include() [function.include]: Failed opening 'http://www.domain.com/footer.html' for inclusion (include_path='.:/usr/lib/php:/usr/local/lib/php') in /home/domain/public_html/test/index.php on line 12 Any clue what can be wrong with Apache or PHP configuration? Thanks

  Read the article

• Home network with two isolated separate subnets, running on cablemodem/router and WRT-router.

  - by Johan Allgoth

  I have a new connection with a nice new router/cable-modem. I'd like to setup it up optimally and needs some pointers. I am a complete n00b when it comes to routing. I want to end up with two separate subnets, 10.1.2.0/24 and 192.168.1.0/24 each available on their own wireless channel/SSID. Both firewalled. I want my wired computers on the gigabit switch, optimally with public ips. I want to be able to reach 192.168.1.0/24 from 10.1.2.0/24, but not vice versa. Everyone should have internet access. Hardware and capabilities: Netgear CG3100. Handles cable connection. Gigabit switch. 802.11n. Can do DHCP, firewall, NAT etc. Can choose subnet. Can turn of NAT and if so hand out up to 4 public ips. Somewhat challenged when it comes to configuration. WRT-router. Runs DD/Open-WRT very stable. 100 Mbit switch. 802.11.g Can do DHCP, firewall, NAT etc. Can choose subnet. Highly configurable. I hope to be able to keep 10.1.2.0/24 on the CG3100, for speed reasons and 192.168.0.0/24 on the WRT-router for quota and user control reasons. On my 10.1.2.0/24 network I plan on running servers for various services. Should I turn of NAT on the WRT-router? Or on the cable modem? Activate what in that case? Is double NAT always f-ed up?

  Read the article

• HP G61 Laptop wont boot- display stays off, caps and num lock indicators blink repeatedly

  - by Benguy12

  I had my HP G61 laptop running in sleep for a while. When I came back to it about a half-hour later, it was no longer in sleep mode - the power light and the Wi-Fi indicator light were on (I keep Wi-Fi off becuase I use a wired connection) - but nothing was showing on screen. In fact, the display wasn't even turned on. So I let it sit for about 10 minutes but nothing happened. I did a force shut down and rebooted. Instead of a normal boot, the display didnt turn on, the Wi-Fi indicator was off, and the Caps Lock and Num Lock lights just blinked repeatedly. On the external keyboard i use, none of the light indicators were blinking or even on. I tried force shut-down again 10 times, then unplugged all connections except for the power cable (my laptop battery dosent hold a charge for more than 2 minutes, so I always must have a wall connection) and tried to boot again but still nothing happened. I unplugged the battery and even then nothing happened. I also tried booting with the disk drive open, and then with it closed again. On the time it was closed, I was able to successfully boot into Windows, but recieved a "Windows did not shut-down sucessfully" notice. Does anybody know why this may have happened? My PC's specs: Windows 7 Home Premium, 64-bit 4GB of physical RAM, 8GB of vRAM (on a flash drive) AMD Vision x64 processor (don't know any other specs about it) ATI Radeon graphics card, 392 MB DVD-R/W lightscribe drive 2 External hard-disks (first one is 1.5TB, second one is 1TB) custom boot-screen and boot-annimation Standard BIOS apps running before sleep: firefox 10.4 itunes 10.6 adobe photoshop extended CS5.1 rockstar games social club (running in background) microsoft powerpoint 2010 professional edition google chrome I was NOT running Aero or any fancy themes - I was using the normal windows classic theme. I have a desktop icon manager application called Stardock Fences that was also running (it runs as a service/process).

  Read the article

• how i can identify which process is making UDP traffic on linux?

  - by boos

  my machine is continously making udp dns traffic request. what i need to know is the PID of the process generating this traffic. The normal way in TCP connection is to use netstat/lsof and get the process associated at the pid. Is UDP the connection is stateles, so, when i call netastat/lsof i can see it only if the UDP socket is opened and it's sending traffic. I have tried with lsof -i UDP and with nestat -anpue but i cant be able to find wich process is doing that request because i need to call lsof/netstat exactly when the udp traffic is sended, if i call lsof/netstat before/after the udp datagram is sended is impossible to view the opened UDP socket. call netstat/lsof exactly when 3/4 udp packet is sended is IMPOSSIBLE. how i can identify the infamous process ? I have already inspected the traffic to try to identify the sended PID from the content of the packet, but is not possible to identify it from the contect of the traffic. anyone can help me ? I'm root on this machine FEDORA 12 Linux noise.company.lan 2.6.32.16-141.fc12.x86_64 #1 SMP Wed Jul 7 04:49:59 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux

  Read the article

• Ways to have audio output without wires

  - by viraptor

  I'm trying to find a way of using my home speakers/amp without actually having to connect them. There are two laptops that use them normally (so I don't like changing the connection all the time) and I'd rather move the speakers to a place that's away from the couch. I'm not sure how to do this though... The options I can think of are: some kind of wireless jack-jack connection finally getting a media server Unfortunately I can't find any good product for the first solution. I've seen some headphones which have the receiver integrated and a separate transmitted, so in general the idea is already out there, just not the way I need ;) I've seen also http://www.miccus.com/products/blubridge-mini-jack, but I'd have to have a compatible receiver which I can't find on its own (maybe there's some application that the media server could use?). As far as media server goes... many of the plug servers look really interesting, but I'm not sure how to create an audio output and how to redirect the input really. None of the plug servers I've seen so far advertises the option of audio output jack port. I think this part could be fixed by getting one with an usb port and a separate cheap usb soundcard. I hope that input can be sorted out in some rather simple way. I've got Linux running on both laptops so I hope that would be possible to configure jack/pulse/whatever to use the remote endpoint, or even write a simple local-/dev/dsp:network:media-server-/dev/dsp forwarder. So the main question is... are there better ways? Are there any out of the box solutions? Or maybe this was already done by someone and described somewhere?

  Read the article

• Unable to receive emails from Ubuntu postfix mail server

  - by Paddington

  I am unable to receive emails on an Ubuntu 11.04 server running postfix with the Plesk control panel. I can't see the mails even on webmail. I am able to send emails and am not getting any error messages on the email client when I try to receive. Here is the output of the logs: *tail -f /usr/local/psa/var/log/maillog Aug 29 10:38:31 cp9 postfix/tlsmgr[3811]: fatal: open database /var/lib/postfix/smtpd_scache.db: Invalid argument Aug 29 10:38:32 cp9 postfix/master[27738]: warning: process /usr/lib/postfix/tlsmgr pid 3811 exit status 1 Aug 29 10:38:32 cp9 postfix/master[27738]: warning: /usr/lib/postfix/tlsmgr: bad command startup -- throttling Aug 29 10:38:36 cp9 pop3d: Connection, ip=[::ffff:196.201.7.158] Aug 29 10:38:36 cp9 pop3d: IMAP connect from @ [::ffff:196.201.7.158]INFO: LOGIN, [email protected], ip=[::ffff:196.201.7.158] Aug 29 10:38:37 cp9 pop3d: 1346229517.874008 LOGOUT, [email protected], ip=[::ffff:196.201.7.158], top=0, retr=0, time=1, rcvd=24, sent=1716, maildir=/var/qmail/mailnames/essentialhuku.co.za/earle/Maildir Aug 29 10:14:05 cp9 postfix/tlsmgr[1133]: fatal: open database /var/lib/postfix/smtpd_scache.db: Invalid argument Aug 29 10:14:06 cp9 postfix/master[27738]: warning: process /usr/lib/postfix/tlsmgr pid 1133 exit status 1 Aug 29 10:14:06 cp9 postfix/master[27738]: warning: /usr/lib/postfix/tlsmgr: bad command startup -- throttling Aug 29 10:14:08 cp9 pop3d: Connection, ip=[::ffff:196.201.7.158

  Read the article

• Exchange 2013 attachments too big?

  - by KPS

  I am having the toughest time sending large attachments, everywhere I have checked my file size limit for send/receive is 100mb but yet users are unable to receive files even at the size of 14mb. I'm using a spam filter (Appriver) and have worked with there support for a very long time, we see the following errors in logs 13:32:40.260 4 SMTP-000036([myserverIP]) rsp: 354 Start mail input; end with <CRLF>.<CRLF> 13:33:41.038 3 SMTP-000033([myserverIP]) write failed. Error Code=connection reset by peer 13:33:41.038 3 SMTP-000033([myserverIP]) [659500] failed to send. Error Code=connection reset by peer 13:33:41.038 4 SMTP([myserverIP]) [659500] batch reenqueued into tail Windows firewall is disabled on the exchange server, all other emails that are of smaller value come through just fine. Here is a print out of size limits: ConnectorType ConnectorName MaxReceiveMessageSize MaxSendMessageSize ------------- ------------- --------------------- ------------------ Send InternetSendConnector - 35 MB (36,700,160 bytes) Send Appriver-Smarthost - 35 MB (36,700,160 bytes) Receive Default EXCHSRVR 100 MB (104,857,600 bytes) - Receive Client Proxy EXCHSRVR 100 MB (104,857,600 bytes) - Receive Default Frontend EXCHSRVR 100 MB (104,857,600 bytes) - Receive Outbound Proxy Frontend EXCHSRVR 100 MB (104,857,600 bytes) - Receive Client Frontend EXCHSRVR 100 MB (104,857,600 bytes) - Receive ExchangeRelay 100 MB (104,857,600 bytes) - TransportConfig - 100 MB (104,857,600 bytes) 10 MB (10,485,760 bytes) ADSiteLink DEFAULTIPSITELINK Unlimited Unlimited There is a no anti-virus on the server either that could be interfering, I am out of ideas at this point :( EDIT 1 After running BPA, it gives and error: Exchange Organization: Check whether the incoming message(CN=MyDomain,CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=WG,DC=local) size isn't set The maximum incoming message size isn't set in organization 'CN=MyDomain,CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=WG,DC=local'. This can cause reliability problems. Here are the sizes as of now: [PS] C:\Temp>Get-TransportConfig | ft MaxSendSize, MaxReceiveSize MaxSendSize MaxReceiveSize ----------- -------------- Unlimited Unlimited [PS] C:\Temp>Get-ReceiveConnector | ft name, MaxMessageSize Name MaxMessageSize ---- -------------- Default EXCHSRVR 100 MB (104,857,600 bytes) Client Proxy EXCHSRVR 100 MB (104,857,600 bytes) Default Frontend EXCHSRVR 100 MB (104,857,600 bytes) Outbound Proxy Frontend EXCHSRVR 100 MB (104,857,600 bytes) Client Frontend EXCHSRVR 100 MB (104,857,600 bytes) ExchangeRelay 100 MB (104,857,600 bytes) Again, smaller emails come through just fine. Seems like there is a 10mb receive limit somewhere that I cannot find.

  Read the article

• How do I correctly SSH port forward using LiveReload on Redhat?

  - by program247365

  Referencing this page: http://feedback.livereload.com/knowledgebase/articles/86280-if-you-edit-files-directly-on-your-server It says you can remotely port forward the LiveReload specific port of 35729, using this command: ssh -L 35729:127.0.0.1:35729 mylogin@myremoteserverIP When I run the -v option, I get: debug1: Local connections to LOCALHOST:35729 forwarded to remote address 127.0.0.1:35729 debug1: Local forwarding listening on ::1 port 35729. debug1: channel 0: new [port listener] debug1: Local forwarding listening on 127.0.0.1 port 35729. debug1: channel 1: new [port listener] debug1: channel 2: new [client-session] debug1: Entering interactive session. debug1: Sending environment. debug1: client_input_channel_req: channel 2 rtype [email protected] reply 1 debug1: Connection to port 35729 forwarding to 127.0.0.1 port 35729 requested. debug1: channel 3: new [direct-tcpip] channel 3: open failed: connect failed: Connection refused debug1: channel 3: free: direct-tcpip: listening port 35729 for 127.0.0.1 port 35729, connect from 127.0.0.1 port 63673, nchannels 4 I thought editing my /etc/services with this line, would work, but it doesn't: livereload 35729/tcp # livereload usage with guard-livereload Every time I attempt to connect with the browser extension, I believe It's getting blocked by my server. What am I missing here? Do I need to edit /etc/services for this to work?

  Read the article

• Cannot find wireless driver for HP laptop

  - by rodey

  I have an HP laptop (model: dv7-1267cl, Windows 7 64-bit Home Premium) and I cannot find the wireless driver for the laptop. I am need of a different version because my wireless connection under Windows is flaky and unreliable. I have problems printing to my wireless printer and logging in to and using several sites like reddit.com, phoenix.edu and facebook.com - I get several "page cannot be displayed" messages while using my wireless connection. I disable my wireless adapter and use an ethernet cable and it all works fine. I also used an Ubuntu Live CD to confirm that there is not a problem with the hardware. This is software/driver issue. The drivers were auto installed by the OS. The Device Manager shows the wireless adapter as Atheros AR5009 802.11 a/g/n WiFi Adapter. I have checked the HP website for my laptop and they do not have wireless drivers listed for that model wireless adapter. I have also checked with atheros.com and I do not see my model adapter on their list of available hardware. Device Manager lists the Hardware ID's for my adapter as: PCI\VEN_168C&DEV_002A&SUBSYS_1381103C&REV_01 PCI\VEN_168C&DEV_002A&SUBSYS_1381103C PCI\VEN_168C&DEV_002A&CC_028000 PCI\VEN_168C&DEV_002A&CC_0280 A search for the first Hardware ID turned up this question from experts-exchange.com. tl;dr A driver does not exist for that model adapter.

  Read the article

• How to set up the jdbc driver to connect to hsqldb from libreoffice?

  - by rumtscho

  I am trying to "split" a LibreOffice .odb file into a HSQL database and an OpenOffice document containing forms and macros. I am trying to follow the instructions from this thread: Within a few minutes you can convert your embedded HSQLDB to a stand-alone HSQLDB which is just a very fine database engine. 1) Download and extract the current version from http://hsqldb.org/ and point the Java class path in ToolsOptionsJava to the new hsqldb.jar 2) Extract the database folder from your embedded database and rename the files data, properties, script to name.data name.properties, name.script where "name." is an arbitrary name prefix. 3) Connect a Base document to an existing JDBC database such as jdbc:hsqldb:file:/home/chenier/hsqldb/name;default_schema=true;shutdown=true;hsqldb.default_table_type=cached;get_column_name=false (again, "name" refers to your own file name prefix). This local single-user connection gives you much more than the embedded HSQLDB. 4) Copy queries, forms and reports from the old database over to the new one. The wizard presents me with a window expecting two inputs: a "Datasource URL" and a "JDBC driver class". As far as I can tell, the tutorial above only tells me what to put into the Datasource URL. As for the JDBC driver class, I have no idea what to write into this field. I tried the fully-qualified name of the Java class, org.hsqldb.jdbc.JDBCDriver as given in the HSQLDB documentation. When that failed, I tried the physical path /var/lib/hsqldb/lib/hsqldb.jar (although that should have been unnecessary, because first I pointed to this path as described under 1 and then restarted LibreOffice). In both cases, "Test class" failed with the message "The JDBC driver could not be loaded". OpenOffice's documentation doesn't say anything sensible about the field, it was something like "enter the JDBC driver in this box". Any ideas what I should enter there to get the connection working?

  Read the article

• Connecting remotely to an SQL server inside a LAN

  - by vondip

  Hello everyone, I am using SQL server 2008 inside my home lan. I've configured it to accept remote connections and I can now connect to the server from other pcs inside the lan. The problems rises when I try connecting to the server from a computer outside of my home lan. I've disabled my router's firewall and I've configured a virtual server on port 1433 forwarding to the correct lan ip. What's wrong? why is it not working? Thank you very much for your help~! Edit: This is the error I keep getting: A network related or instance specific error occured while establishing connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that the SQL SERVER is configued to allow remote connections. (provider : Sql network interfaces, error: 25- Connection string is not valid) OK these are my router's details: edimax br-6204wg I am not sure how I am supposed to browse google.com. can you be a bit more specific?

  Read the article

• iptables port forward + nginx redirect problem

  - by easthero

  Here is my network browser = proxy(iptables port forward) = nginx server proxy: 192.168.10.204, forward 192.168.10.204:22080 to 192.168.10.10:80 nginx server: 192.168.10.10 nginx version:0.7.65 debian testing in nginx settings, I set: server_name _; server_name_in_redirect off; because my server has no domain now, access 192.168.10.10/index.html or 192.168.10.10/foobar is ok then access 192.168.10.204:22080/index.html is ok but access 192.168.10.204:22080/foobar, nginx 301 redirect to http://192.168.10.204/foobar how to fix? thanks telnet 192.168.10.204 22080 Trying 192.168.10.204... Connected to 192.168.10.204. Escape character is '^]'. GET /index.html HTTP/1.1 Host: 192.168.10.10 HTTP/1.1 200 OK Server: nginx/0.7.65 Date: Fri, 28 May 2010 10:07:29 GMT Content-Type: text/html Content-Length: 12 Last-Modified: Fri, 28 May 2010 07:25:12 GMT Connection: keep-alive Accept-Ranges: bytes hello world telnet 192.168.10.204 22080 Trying 192.168.10.204... Connected to 192.168.10.204. Escape character is '^]'. GET /test2 HTTP/1.1 Host: 192.168.10.10 HTTP/1.1 301 Moved Permanently Server: nginx/0.7.65 Date: Fri, 28 May 2010 10:04:20 GMT Content-Type: text/html Content-Length: 185 Location: http://192.168.10.10/test2/ Connection: keep-alive <html> <head><title>301 Moved Permanently</title></head> <body bgcolor="white"> <center><h1>301 Moved Permanently</h1></center> <hr><center>nginx/0.7.65</center> </body> </html>

  Read the article

• ddclient to update namecheap subdomain?

  - by LF4

  I have a subdomain that I want to update with ddclient. I configured the ddclient to get the IP from dyndns but it's not updating the subdomain on namecheap. They said to use yourdomain.com as the login instead of my actual domain. Has anyone been able to get namecheap DNS updated with ddclient? I'm running CentOS 6.2 with ddclient 3.7.3. When I run ddclient I get the following. CONNECT: checkip.dyndns.org CONNECTED: using HTTP SENDING: GET / HTTP/1.0 SENDING: Host: checkip.dyndns.org SENDING: User-Agent: ddclient/3.7.3 SENDING: Connection: close SENDING: RECEIVE: HTTP/1.1 200 OK RECEIVE: Content-Type: text/html RECEIVE: Server: DynDNS-CheckIP/1.0 RECEIVE: Connection: close RECEIVE: Cache-Control: no-cache RECEIVE: Pragma: no-cache RECEIVE: Content-Length: 106 RECEIVE: RECEIVE: <html><head><title>Current IP Check</title></head><body>Current IP Address: IPADD</body></html> Use of uninitialized value in string ne at /usr/sbin/ddclient line 1998. WARNING: skipping update of lf4bot from <nothing> to IPADD WARNING: last updated <never> but last attempt on Fri Jun 15 22:46:21 2012 failed. WARNING: Wait at least 5 minutes between update attempts. ddclient.conf File daemon=300 # check every 300 seconds syslog=yes # log update msgs to syslog mail=root # mail all msgs to root mail-failure=root # mail failed update msgs to root pid=/var/run/ddclient.pid # record PID in file. ssl=yes # use ssl-support. Works with use=web, web=checkip.dyndns.org/, web-skip='IP Address' # found after IP Address protocol=namecheap \ server=dynamicdns.park-your-domain.com \ login=yourdomain.com \ password=PASSWORD \ lf4bot

  Read the article

• Google Chrome doesn't want to access Facebook

  - by Pieter van Niekerk

  I have been experiencing a bit of a problem with Chrome over the last couple of days where it doesn't want to access Facebook. When I open Chrome it works fine for a while and then if I were to refresh the page it would give me the Chrome 'This webpage is not available' message. This webpage is not available Google Chrome could not load the webpage because www.facebook.com took too long to respond. The website may be down, or you may be experiencing issues with your Internet connection. Here are some suggestions: Reload this webpage later. Check your Internet connection. Restart any router, modem, or other network devices you may be using. Add Google Chrome as a permitted program in your firewall's or antivirus software's settings. If it is already a permitted program, try deleting it from the list of permitted programs and adding it again. If you use a proxy server, check your proxy settings or contact your network administrator to make sure the proxy server is working. If you don't believe you should be using a proxy server, adjust your proxy settings: Go to the wrench menu Options Under the Hood Change proxy settings... LAN Settings and deselect the "Use a proxy server for your LAN" checkbox. This problem only persists when using the proxy and doesn't occur at all when not on the proxy. I have also tried different browsers (IE9 and Firefox 9.01) but it doesn't occur in any of them. This problem goes away for a while when I restart Chrome, only to happen again a couple of minutes later. I have tried deleting the cookies for Facebook without restarting Chrome, but to no avail. I am using Windows7 with Chrome 17

  Read the article

• Connecting jconsole using SOCKS to Amazon EC2

  - by freshfunk

  I'm trying to use jconsole to view stats on an EC2 instance by using a socks proxy created by SSH. I've tried the various scripts mentioned in the links below but to no avail: http://simplygenius.com/2010/08/jconsole-via-socks-ssh-tunnel.html http://gabrielcain.com/blog/2010/11/02/using-ssh-proxying-to-connect-jconsole-to-remote-cassandra-instances/ I'm running ssh -f -ND 8123 myuser@mymachine and verified that at least Firefox goes through it as a proxy. I then run jconsole -J-DsocksProxyHost=localhost -J-DsocksProxyPort=8123 service:jmx:rmi:///jndi/rmi://ec2-XX-XX-XXX-XXX.compute-1.amazonaws.com:8080/jmxrmi I run netstat -n on my EC2 instance and I see a connection created by my machine. However, the connection eventually disappears and I get a 'channel 2: open failed: connect failed: Operation timed out' from my ssh tunnel. I've opened the jmx port through the security group and I've checked the port on the EC2 instance to make sure it's open (by telnet-ing to it). I'm not sure where to look next. Are there some properties in sshd_config or ssh_config I need to enable for tunneling? Or anything in Mac OS X? I feel like a serious noob but sys administration is really not my strong point. I've spent several hours and can't get this to work.

  Read the article

< Previous Page | 389 390 391 392 393 394 395 396 397 398 399 400  | Next Page >