Search Results

Search found 15038 results on 602 pages for 'programming late night'.

Page 395/602 | < Previous Page | 391 392 393 394 395 396 397 398 399 400 401 402  | Next Page >

  • Intermittent Trouble Entering Hibernate on WinXP

    - by kquinn
    My personal desktop, running 32-bit Windows XP SP2 (with 4GB RAM, 2.75GB addressable, swap disabled, hiberfil.sys existing and contiguous on C:\; SP3 is not installed because SP2 has been working fine and I do not want to re-qualify with SP3 just for sheer perversity) typically gets hibernated at night. For a long time this worked great, but recently the machine has had trouble entering hibernation. Sometimes when I press my power button (configured to hibernate), the box will start the procedure for hibernating (i.e., go to the blue "Windows XP" background logo and display a message about entering hibernation), but before displaying the usual blue-on-black hibernation progress bar it will drop back to the desktop. No error messages appear, on screen or in the system log. The only record of unsuccessful hibernation attempts in the system log, which proudly proclaims that "The Windows Image Acquisition (WIA) service entered the running state." once per failed hibernation attempt. The problem is almost certainly resource related: if I then close one or more applications which are running, and repeat the exact same process, the machine will hibernate perfectly. There does not appear to be a reliable high-water mark for virtual or physical memory use, below which the machine is guaranteed to hibernate; it's different every time (though typically, below about 1.1–1.4 GB memory usage seems to be where hibernate succeeds most often). Memory may not even be the relevant resource; as far as I know, it could also be handles or sockets. This behavior is relatively recent: it has only started in the last few months; before then, I could hibernate reliably no matter what the current resource use of the system. This machine claims to have hotfix Q909095 installed, but since the symptoms of my problem match KB909095 rather well, I'm suspicious if this fix is actually working as intended. Any ideas on how to fix this or where to start debugging?

    Read the article

  • Laptop Randomly Turning On and Off

    - by Ian Mallett
    So, I have a pretty new laptop, and one of its quirks is that, at random times (though typically in the middle of the night), it seems to wake up from sleep mode, churn a bit, and then go back into sleep mode. I write "seems" because its fans are very loud, so it's obvious when it's not asleep, but during the time it is "on", I can't see anything on the screen. I have researched the problem somewhat, and could only find similar issues; nothing identical. In those cases, it appeared that certain devices could be responsible. Nothing is plugged into my computer during this behavior, but I nonetheless disabled every device's permission to wake the computer through the device manager. This included disabling the magic packet wake for the network (despite its only having a wireless connection). Using "powercfg /lastwake" gives an empty wake history. But, I also went through all the tasks and checked if they would wake the computer. None appeared to. The problem persisted, so, after some more research, I found this, and executed it for all power schemes on the computer. The problem persists. System: OS: Windows 7 Professional CPU: Intel 990X GPU: NVIDIA GeForce 580M/12GB RAM Motherboard: Clevo X7200 Model: NP7282-S1 (Sager-built laptop)

    Read the article

  • Switch case assembly level code

    - by puffadder
    Hi All, I am programming C on cygwin windows. After having done a bit of C programming and getting comfortable with the language, I wanted to look under the hood and see what the compiler is doing for the code that I write. So I wrote down a code block containing switch case statements and converted them into assembly using: gcc -S foo.c Here is the C source: switch(i) { case 1: { printf("Case 1\n"); break; } case 2: { printf("Case 2\n"); break; } case 3: { printf("Case 3\n"); break; } case 4: { printf("Case 4\n"); break; } case 5: { printf("Case 5\n"); break; } case 6: { printf("Case 6\n"); break; } case 7: { printf("Case 7\n"); break; } case 8: { printf("Case 8\n"); break; } case 9: { printf("Case 9\n"); break; } case 10: { printf("Case 10\n"); break; } default: { printf("Nothing\n"); break; } } Now the resultant assembly for the same is: movl $5, -4(%ebp) cmpl $10, -4(%ebp) ja L13 movl -4(%ebp), %eax sall $2, %eax movl L14(%eax), %eax jmp *%eax .section .rdata,"dr" .align 4 L14: .long L13 .long L3 .long L4 .long L5 .long L6 .long L7 .long L8 .long L9 .long L10 .long L11 .long L12 .text L3: movl $LC0, (%esp) call _printf jmp L2 L4: movl $LC1, (%esp) call _printf jmp L2 L5: movl $LC2, (%esp) call _printf jmp L2 L6: movl $LC3, (%esp) call _printf jmp L2 L7: movl $LC4, (%esp) call _printf jmp L2 L8: movl $LC5, (%esp) call _printf jmp L2 L9: movl $LC6, (%esp) call _printf jmp L2 L10: movl $LC7, (%esp) call _printf jmp L2 L11: movl $LC8, (%esp) call _printf jmp L2 L12: movl $LC9, (%esp) call _printf jmp L2 L13: movl $LC10, (%esp) call _printf L2: Now, in the assembly, the code is first checking the last case (i.e. case 10) first. This is very strange. And then it is copying 'i' into 'eax' and doing things that are beyond me. I have heard that the compiler implements some jump table for switch..case. Is it what this code is doing? Or what is it doing and why? Because in case of less number of cases, the code is pretty similar to that generated for if...else ladder, but when number of cases increases, this unusual-looking implementation is seen. Thanks in advance.

    Read the article

  • work benefits package [closed]

    - by Francisco Garcia
    For those of you who are into programming not just for the money. I would like to know which benefits you would like to have (or already have). OK, maybe taking away the money factor will limit this question too much. I am surprised to see that most companies have a fixed set for their benefits package. Were you able to negotiate something new or just your salary? What things have you seen out there and/or value most?

    Read the article

  • How to replace empty string with zero in comma-separated string?

    - by dsaccount1
    "8,5,,1,4,7,,,,7,,1,9,3,6,,,8,6,3,9,,2,5,4,,,,,3,2,,,7,4,1,1,,4,,6,9,,5,,,,5,,,1,,6,3,,,6,5,,,,7,4,,1,7,6,,,,8,,5,,,7,1,,3,9," I'm doing a programming challenge where i need to parse this sequence into my sudoku script. Need to get the above sequence into 8,5,0,1,4,7,0,0,0,7,0,1,9,3,6,0,0,8......... I tried re but without success, help is appreciated, thanks.

    Read the article

  • Where can I find a good software implementation plan template?

    - by Corpsekicker
    This is not "programming" related as much as it is "software engineering" related. I am required to produce an implementation for additional functionality to a complete system. All I am armed with is knowledge of the existing architecture and a functional spec with visual requirements, user stories and use cases. Is there a standardised way to go about this? I suck at documentation.

    Read the article

  • IDE for Common Lisp (for windows and linux)

    - by sterh
    Hi to all, I need in IDE for Common Lisp, but at home i use linux and emacs + slime for lisp programming, but in my university i must use MS Windows, Emacs under Windows ... pull configuration file and the other I just do not do suits. Please advise a comfortable IDE for Common lisp that would have been a version for Windows and Linux and setup and installation would not cause difficulties. Thank you.

    Read the article

  • Computer sponteously reboots when doing heavy file copy to/from disk

    - by Mark Hosang
    I've been fighting with this problem for the last 3 weeks where my machine will just instantly reboot. No BSOD, and when i checked the event log all that was reported was the generic "Kernal-power" error with the detailed information pointing to a hard crash. This is a machine that was working for 18 months before these crashes started happening. When they started happening is after I added 3 HDs in a RAID-5, upped the memory to 12gb, moved to a new house, added a SSD and added about 5 case fans. I have thus eliminated the RAID, and determined that the SSD was not the cause (because it was still crashing even though the ssd wasn't connected). I've run memtest several times over night with no memory problems showing up. I've run IntelBurnTest to max out the cpu to see if it was a heat issue and at full tilt after 20 min it was only at 85C and the machine didn't crash. I also took a look at the voltages during this test, with a screenshot at the bottom of this post I've ruled out a software issue by reinstalling windows 7 ultimate x64 a total of 5 times, but even during that the install it crashes. Happens sometime during file copying at the beginning, or during uncompressing files, or sometimes during running windows update. The only discernible pattern i can see is that it seems to crash when hard disks might be spinning up or when they are accessed heavily from large file transfers. My current guess is that it is probably an issue with the MB, PSU or the power coming through the outlet. Any suggestions of what i could try to troubleshoot or what may be wrong? Specs PSU: Seasonic M12 700w Mem: 12gb CPU: i7-920 with stock heatsink MB: Asus P6T HDs: 3 green WD and 1 Corsair force 3 120b with 1.3.3 firmware Running full tilt voltages Idling Voltages

    Read the article

  • Implementing the procducer-consumer with .NET 4.0 new

    - by bitbonk
    With alle the new paralell programming features in .NET 4.0, what would be a a simple and fast way to implement the producer-consumer pattern (where at least one thread is producing and enqueuing task items and one other thread executes (dequeues) these tasks). Can we benfit from all these new APIs? What is your preferred implementation of this pattern?

    Read the article

  • Getting 0xc00000e windows 7 "Boot device inaccessible" after random crashes

    - by Dynde
    I've been having some weird random crashes that I can't seem to locate, and I'm unsure if it's windows or hardware related. It's a brand new computer and very powerful. I've run into a couple of these random crashes, now I don't know what causes them, as it happens during the night, when I'm sleeping. When I wake up, all I see is a boot manager screen that says Exception: 0xc00000e "Boot device inaccessible". A simple restart doesn't fix the problem - it seems to struggle locating my primary hdd - but a complete shutdown works, it'll just fly straight into windows again. The event viewer doesn't tell me much. The most reason incident just gives me this: "The previous system shutdown at 08:55:44 on ?11-?12-?2011 was unexpected." And also a kernel power event: The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. and I can see only two application event entries around that time at 8.47 (about 8 minutes prior to the crash): The Windows Modules Installer service entered the running state. The WinHTTP Web Proxy Auto-Discovery Service service entered the running state. Can anyone tell me anything about this, or direct me to a forum or something that might know what's wrong? I can supply the extra details of the events too if needed. The hdd is an SSD - could that have anything to do with it? I ran a few diagnostics and memory and hdd should be okay - at least the diagnostics report is clean. Is it a faulty drive?

    Read the article

  • Where can I find an ADOExpress tutorial?

    - by mawg
    I'm using Delphi 7, totally new to database programming, and need ODBC. I am told that ADOExpress is a good way to go, and that seems fair enough as it comes with Delphi 7. I need to programatically create, populate, modify and query a database (currently MySql, but that might change, hence ODBC). Can anyone recommend a good tutorial? Thanks.

    Read the article

  • Conventions for modelling c programs.

    - by Hassan Syed
    I'm working with a source base written almost entirely in straight-c (nginx). It does, however, make use of rich high level programming techniques such as compile-time metaprogramming, and OOP - including run-time dispatch. I want to draw ER diagrams, UML class diagrams and UML sequence diagrams. However to have a clean mapping between the two, consistent conventions must be applied. So, I am hopping someone has some references to material that establishes or applies such conventions to similar style c-code.

    Read the article

  • Can somebody link me to some code where there is a fantastic or a nice use of Inheritance

    - by Soham
    I strongly believe that, reading code and reading good code is key to great programming. If not one of the many. I had been facing some problems in visualizing and having a "feel" of using inheritance to better my code architecture. Can somebody give me some link to good code to emulate, where folks have used inheritance in an absolute "kung-fooey ruthless" manner [in a good way]

    Read the article

  • Implementing Communication Protocols on CC2420 motes powered by TinyOS

    - by stanigator
    I would like to load TinyOS on CC2420 radio motes to operate on certain communication protocols (e.g. epidemic routing, probabilistic routing, etc.). However, I have no prior experience in programming motes to perform the protocols I want. I'm just wondering about the most applicable resources for reference and how difficult (if not impossible) was implementing such mentioned protocols. It would be great to hear from you. Thanks in advance!

    Read the article

  • Webcam capture and convert to avi

    - by Spidfire
    Im trying to make a program that captures a video from the webcam and sound from the microphone but im getting stuck at the part where ive try to make a movie out of still images ive heard you need to use directshow but it doesnt jet work for me Does someone know a good piece of example code that captures video and sound and can encode it to a file (divx or something like that) ? or some suggestions where to look so i can build it myself (if a other programming language is better for this im happy to know it early. )

    Read the article

  • Subdocument in Word won't save

    - by ChrisW
    Because I know Word has a history of not liking very large documents (my supervisor specifically told me not to use LaTeX... grr), I decided to learn the Master document / subdocument feature of Word when writing my PhD thesis. I have the title page / table of contents etc in the master document, and each chapter as a separate document. However, when I save the master document, it appears to save all the chapter documents apart from one (Chapter 4), for which it brings up the Save Document dialog box, helpfully with "Chapter4.docx" in the "Save as" box (n.b. Chpater4.dox is not open). Clicking save does nothing, and doesn't make the dialog box go away. Saving as a different document means that my changes aren't reflected in the same document. There must be some reason Word doesn't like this particular document but I've got no idea why - there's nothing special in it that isn't in any of the other chapters. I have tried closing all documents, renaming Chapter4.docx, opening the master document, expanding all documents, OKing the warning that Chapter4.dox does not exist, and inserting the 'new' document, but even when I save the master document it still won't save the new Chapter4 document. If anyone knows any reason why Word is acting like this (or if I'm doing anything stupid), I'll be eternally grateful (p.s. sorry for the long rambling message. It's late; I've been working on my PhD 4.5 years, I really really want to throw this computer out the window, and I hope people are kind enough not to downvote this question because of it's rambling nature!) Update With Word closed, I've tried to delete Chapter4.docx (having made a backup!) - but I get a warning that it can't be deleted because it's open in Microsoft Word... these files are on a network drive and the same problems are happening on 2 different computers. I could login to the filestore through ssh and force the file to be deleted, but I'm curious to know why this is happening!

    Read the article

< Previous Page | 391 392 393 394 395 396 397 398 399 400 401 402  | Next Page >