Search Results

Search found 11015 results on 441 pages for 'explain plan'.

Page 396/441 | < Previous Page | 392 393 394 395 396 397 398 399 400 401 402 403  | Next Page >

• Windows XP machine not seeing external FAT32 partitions correctly

  - by Rob_before_edits

  About 8 months ago my Windows XP machine stopped being able to see FAT32 external drives when I plug them in... mostly. I will explain... It happens with all my FAT32 drives, whether they be unpowered external hard drives, powered external hard drives, SDHC cards plugged directly into the machine's card reader, or SDHC cards plugged in via a separate USB card reader. All of these drives/cards used to work fine on this machine. They all stopped working at about the same time. NTFS volumes are not affected. If I plug in NTFS external drives they are recognized right away. I even have one external drive with two partitions on it, one is NTFS which is recognized, the other is FAT32, which is not recognized. If I attach a FAT32 drive, then reboot, then the drive almost always becomes visible to the machine after the reboot. Sometimes I can plug in a FAT32 drive and it works right away. Not often though. I'd say I get lucky more often with SDHC cards than hard drives. I'm developing a theory that I only get lucky with hard drives if I'm running Acronis Disk Director when I plug them in, though that usually doesn't work either - I need more data here, this may be a red herring. Getting lucky with a hard drive is really rare, usually I have to reboot. When a FAT32 is recognized, either because I got lucky or because I rebooted, I can almost never safely disconnect it. It tells me "The device 'Generic volume' cannot be stopped right now. Try stopping the device again later". I can't seem to get around this. IIRC, I've tried closing every open window, and still no luck. Since I care about my data usually the only way to disconnect a FAT32 drive is to shut down the machine. As you can imagine, two reboots just to read a drive is getting pretty old... When the machine fails to see a FAT32 drive it usually comes up with the appropriate drive letter and the words "Local Disk" in Windows Explorer instead of the correct partition name. If I click on it I get "J:\ is not accessible. The parameter is incorrect." Before this problem arose I always clicked the "safely remove" button for everything, including SDHC cards where I think it's not necessary. I've known for a long time that this is the correct procedure for hard drives, so I don't think failing to do this was the cause of this problem (before someone asks :) Any answers or suggestions most welcome.

  Read the article

• Filtering Security Logs by User and Logon Type

  - by Trido

  I have been asked to find out when a user has logged on to the system in the last week. Now the audit logs in Windows should contain all the info I need. I think if I search for Event ID 4624 (Logon Success) with a specific AD user and Logon Type 2 (Interactive Logon) that it should give me the information I need, but for the life of my I cannot figure out how to actually filter the Event Log to get this information. Is it possible inside of the Event Viewer or do you need to use an external tool to parse it to this level? I found http://nerdsknowbest.blogspot.com.au/2013/03/filter-security-event-logs-by-user-in.html which seemed to be part of what I needed. I modified it slightly to only give me the last 7 days worth. Below is the XML I tried. <QueryList> <Query Id="0" Path="Security"> <Select Path="Security">*[System[(EventID=4624) and TimeCreated[timediff(@SystemTime) &lt;= 604800000]]]</Select> <Select Path="Security">*[EventData[Data[@Name='Logon Type']='2']]</Select> <Select Path="Security">*[EventData[Data[@Name='subjectUsername']='Domain\Username']]</Select> </Query> </QueryList> It only gave me the last 7 days, but the rest of it did not work. Can anyone assist me with this? EDIT Thanks to the suggestions of Lucky Luke I have been making progress. The below is my current query, although as I will explain it isn't returning any results. <QueryList> <Query Id="0" Path="Security"> <Select Path="Security"> *[System[(EventID='4624')] and System[TimeCreated[timediff(@SystemTime) &lt;= 604800000]] and EventData[Data[@Name='TargetUserName']='john.doe'] and EventData[Data[@Name='LogonType']='2'] ] </Select> </Query> </QueryList> As I mentioned, it wasn't returning any results so I have been messing with it a bit. I can get it to produce the results correctly until I add in the LogonType line. After that, it returns no results. Any idea why this might be? EDIT 2 I updated the LogonType line to the following: EventData[Data[@Name='LogonType'] and (Data='2' or Data='7')] This should capture Workstation Logons as well as Workstation Unlocks, but I still get nothing. I then modify it to search for other Logon Types like 3, or 8 which it finds plenty of. This leads me to believe that the query works correctly, but for some reason there are no entries in the Event Logs with Logon Type equalling 2 and this makes no sense to me. Is it possible to turn this off?

  Read the article

• Authenticate by libpam-mysql and libnss-mysql (CentOS)

  - by Chris

  I'm trying to get MySQL to function as a backend for authenticating users on CentOS 6.3. So far I have successfully installed and configured libnss-mysql. I can test this by doing: # groups testuser testuser : sftp Testuser is a member of the sftp group in fact, all MySQL based useraccounts will be hardcoded to it. The sftp group is chrooted and forced to use internal-sftp so they cannot do anything but access their home directory. Then I configured pam-mysql and PAM to allow mysql logins. This also works.. When SELinux is not enforcing. When I do setenforce 1 users can no longer login. Error: Permission denied, please try again. This is my pam_mysql.conf file: users.host=localhost users.db_user=nss-pam-user users.db_passwd=*********** users.database=sftpusers users.table=users users.user_column=username users.password_column=password users.password_crypt=6 verbose=1 My /etc/pam.d/sshd: #%PAM-1.0 auth sufficient pam_sepermit.so auth include password-auth auth required pam_mysql.so config_file=/etc/pam_mysql.conf account sufficient pam_nologin.so account include password-auth account required pam_mysql.so config_file=/etc/pam_mysql.conf password include password-auth # pam_selinux.so close should be the first session rule session required pam_selinux.so close session required pam_loginuid.so # pam_selinux.so open should only be followed by sessions to be executed in the user context session required pam_selinux.so open env_params session optional pam_keyinit.so force revoke session include password-auth And to be complete the contents of some log files.. /var/logs/secure Nov 20 14:52:20 hostname unix_chkpwd[4891]: check pass; user unknown Nov 20 14:52:20 hostname unix_chkpwd[4891]: password check failed for user (testuser) Nov 20 14:52:20 hostname sshd[4880]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=192.168.10.107 user=testuser Nov 20 14:52:22 sftpusers sshd[4880]: Failed password for testuser from 192.168.10.107 port 51849 ssh2 /var/logs/audit/audit.log type=USER_AUTH msg=audit(1353420107.070:812): user pid=5285 uid=0 auid=500 ses=24 subj=unconfined_u:system_r:sshd_t:s0-s0:c0.c1023 msg='op=pubkey acct="testuser" exe="/usr/sbin/sshd" hostname=? addr=192.168.10.107 terminal=ssh res=failed' type=USER_AUTH msg=audit(1353420112.312:813): user pid=5285 uid=0 auid=500 ses=24 subj=unconfined_u:system_r:sshd_t:s0-s0:c0.c1023 msg='op=PAM:authentication acct="testuser" exe="/usr/sbin/sshd" hostname=192.168.10.107 addr=192.168.10.107 terminal=ssh res=failed' type=USER_AUTH msg=audit(1353420112.456:814): user pid=5285 uid=0 auid=500 ses=24 subj=unconfined_u:system_r:sshd_t:s0-s0:c0.c1023 msg='op=password acct="testuser" exe="/usr/sbin/sshd" hostname=? addr=192.168.10.107 terminal=ssh res=failed' I tried to let audit2why explain the problem but it remains silent even though there are some errors. Does anyone see the problem? Thanks! EDIT: Turns out it's almost working with setenforce 0 I can mkdir foobar but if I do a single ls I get an error: Received message too long 16777216

  Read the article

• Why is Denic not accepting my nameservers?

  - by Oliver Salzburg

  I'm currently in the process of moving all of our domains to our own nameservers. Which wasn't an issue until I hit our own .de domain. I (think I) understand the implications of having the NS inside it's own domain, hence the need for glue records. Until yesterday, I would have assumed I have a pretty good understanding of Bind and DNS zones until I was presented with this error from the Denic nameserver predelegation check: Inconsistent set of nameserver IP addresses (NS, provided glues, determined glues) ns2.hartwig-at.de [88.198.242.190/88.198.242.190] Default resolver determined: [], other resolvers determined: {88.198.242.190/88.198.242.190=[/2a01:4f8:d13:3c85:0:0:0:2, /88.198.242.190]} Inconsistent set of nameserver IP addresses (NS, provided glues, determined glues) ns1.hartwig-at.de [cloud.hartwig-at.de/176.221.46.23] Default resolver determined: [], other resolvers determined: {cloud.hartwig-at.de/176.221.46.23=[/2a00:1158:3:0:0:0:0:b6, /176.221.46.23]} Screenshot of the result The support of my registrar is either far better educated than me or doesn't have a clue. Either way, they're avoiding my questions in regards to what this error means. They just tell me Your nameserver has to return your own nameservers as the default resolver. But that doesn't make any sense to me and they refuse to try to explain it any other way. This is the head of my current zone file: @ 86400 IN SOA ns1.hartwig-at.de. hostmaster.hartwig-at.de. ( 2012070505 ; serial 1d ; refresh 3h ; retry 4w ; expiry 1h ) ; minimum 3600 IN NS ns1.hartwig-at.de. 3600 IN NS ns2.hartwig-at.de. 3600 IN MX 10 remote.hartwig-at.de. 3600 IN MX 20 mx1.hartwig-at.de. 3600 IN MX 30 mx2.hartwig-at.de. localhost 3600 IN A 127.0.0.1 localhost 3600 IN AAAA ::1 @ 3600 IN A 176.221.46.23 3600 IN AAAA 2a00:1158:3::b6 * 3600 IN A 176.221.46.23 3600 IN AAAA 2a00:1158:3::b6 hetzner 3600 IN A 88.198.242.190 hetzner 3600 IN AAAA 2a01:4f8:d13:3c85::2 cloud 3600 IN A 176.221.46.23 cloud 3600 IN AAAA 2a00:1158:3::b6 ; List all NS as A/AAAA record ns 3600 IN A 176.221.46.23 ns 3600 IN AAAA 2a00:1158:3::b6 ns1 3600 IN A 176.221.46.23 ns1 3600 IN AAAA 2a00:1158:3::b6 ns2 3600 IN A 88.198.242.190 ns2 3600 IN AAAA 2a01:4f8:d13:3c85::2 So, what is the problem with my zone? And what is the "default resolver"?

  Read the article

• Add a small RAID card? Will it help overall stability and performance of my nine hard drives?

  - by Ray

  Hi, Will I get any extra genuine added performance and RAID stability if I insert a basic RAID card into a PCI-E x1 slot? I am considering the Adaptec 1220SA - 2 port SATA , pci-express (1x) , raid 0/1. Ok it only supports two SATA drives. Purpose is to help support the eight internal hard drives (1TB each), a DVD drive and an external e-SATA connected 2TB hard drive - by dealing with two of the internal hard drives. My current configuration of eight internal 1TB Barracuda (7200.12) SATA hard drives, one external 2TB SATA Western Digital Green Drive (e-SATA) and one DVD drive can already be supported by the Intel P55 & JMicron controllers on the ASUS motherboard : the Intel P55 (controls six HDD; configured as three x RAID 1), and the JMicron (controls two HDD as one RAID 1, as well as the DVD drive and the external SATA drive via the motherboard's e-SATA port (controlled by the JMicron)). Bigger picture details : I have an ASUS motherboard designed for the LGA1156 type processor and it includes the Intel P55 Express Chipset and JMicron. I am using the Intel Core i7-870 processor, and have 8GB DDR3 (1333) memory (four x 2GB Corsair DIMMs). Enough overall power. The power supply is more than sufficicient for the system. Corsair AX850. The system will never need the full 850 watts (future : second graphics card). The RAID card would provide hardware RAID 1 for two of the eight intrnal drives. It would either reduce the load on : the Intel P55 firmware RAID support, or replace the JMicron controller's RAID 1 set. I am busy installing the above configuration using Windows 7 Ultimate 64-bit as the OS. The RAID card is a last minute addition to the plan. Is it worth spending the extra R700 - R900 on the Adaptec 1220SA, or equivalent RAID card? I cannot afford to spend yet another R2000 - R3000 on a RAID card that would support many SATA2 hard drives, with a better RAID, example the RAID 5. My Issue & assumption : I am trusting that the Intel P55 chipset can properly handle six drives, configured as three * RAID 1. I am assuming that the JMicron can handle, using its RED SATA ports, one RAID-1 (two HDDs). The DVD drive connects to the JMicron optical SATA port 1 (white port 1). White port 2 is not used. The e-SATA connection is from the JMicron straight to, and through the motherboard - to an on-board (rear panel) e-SATA port. Am I being a little hopeful in only using the on-board Intel P55 and the JMicron? Is it a waste of money to install a RAID card that handles two SATA2 drives? OR Is it wisdom to take the pressure a little off the Intel P55? Obviously I am interested in data security, hence RAID 1, not RAID Zero. RAID 5 would be nice. The CPU, Intel Core i7-870 will provide the clout. Context to nine drives : I am using virtualisation with Windows 7 Ultimate. Bootable VMs. The operating system gets a mirror. Loaded apps gets a mirror. The current design data is kept in another mirror and Another mirror is back-up one and / or VM territory. Then the external 2TB drive (via e-SATA) is the next layer of data security and then finally, I use off-site data security. Thanks.

  Read the article

• Latency issues over internet

  - by Stevo

  I have a Media Temple server running http://www.popsapp.com which I am having latency issues with. If I run ab -n 100 -c 10 http://www.popsapp.com/ from my local machine I get very bad stats e.g.: Connection Times (ms) min mean[+/-sd] median max Connect: 179 3375 2185.4 2837 12525 Processing: 0 505 693.3 229 4564 Waiting: 0 50 115.4 0 415 Total: 964 3880 2094.5 3159 12608 Whereas if I run it from a rackspace server I have I get this: Connection Times (ms) min mean[+/-sd] median max Connect: 75 76 3.3 75 84 Processing: 235 339 81.4 315 579 Waiting: 159 249 61.7 234 411 Total: 311 415 82.0 390 663 To me this looks like intermediate network issues, but I wouldn't have thought it could be this bad! Any ideas how I can improve it? Here's the trace route traceroute to www.popsapp.com (216.70.105.183), 64 hops max, 52 byte packets 1 192.168.2.1 (192.168.2.1) 3.738 ms 0.953 ms 1.418 ms 2 host-92-22-112-1.as13285.net (92.22.112.1) 27.409 ms 97.093 ms 78.858 ms 3 host-78-151-225-141.static.as13285.net (78.151.225.141) 61.830 ms 170.484 ms 113.288 ms 4 host-78-151-225-80.static.as13285.net (78.151.225.80) 101.513 ms host-78-151-225-22.static.as13285.net (78.151.225.22) 64.718 ms 47.309 ms 5 xe-11-1-0-rt001.sov.as13285.net (62.24.240.14) 98.381 ms 114.424 ms xe-11-1-0-rt001.the.as13285.net (62.24.240.6) 96.592 ms 6 host-78-144-1-59.as13285.net (78.144.1.59) 36.799 ms host-78-144-1-63.as13285.net (78.144.1.63) 178.426 ms host-78-144-1-61.as13285.net (78.144.1.61) 85.516 ms 7 xe-10-0-0-scr010.thn.as13285.net (78.144.0.224) 88.158 ms host-78-144-0-207.as13285.net (78.144.0.207) 35.132 ms host-78-144-0-153.as13285.net (78.144.0.153) 121.464 ms 8 limelight-pp-thn.as13285.net (78.144.3.6) 46.987 ms limelight-pp-sov.as13285.net (78.144.5.18) 108.025 ms 40.169 ms 9 tge11-1.fr4.lga.llnw.net (69.28.172.149) 109.603 ms ve6.fr4.lon.llnw.net (68.142.88.221) 121.681 ms 38.609 ms 10 tge11-1.fr4.lga.llnw.net (69.28.172.149) 111.981 ms 113.744 ms 111.711 ms 11 tge8-2.fr4.iad.llnw.net (69.28.189.34) 117.102 ms ve5.fr4.iad.llnw.net (69.28.171.214) 184.372 ms 146.178 ms 12 cr02-1-1.iad1.net2ez.com (65.97.48.254) 182.880 ms net2ez.tge2-2.fr4.iad.llnw.net (69.28.156.170) 150.489 ms 121.862 ms 13 65.97.50.26 (65.97.50.26) 184.620 ms cr02-1-1.iad1.net2ez.com (65.97.48.254) 156.136 ms 131.963 ms 14 65.97.50.26 (65.97.50.26) 124.899 ms 126.537 ms 123.322 ms 15 e1.4.as02.iad01.mtsvc.net (70.32.64.246) 134.647 ms 186.307 ms 211.059 ms 16 popsapp.com (216.70.105.183) 118.876 ms 113.189 ms vzx258.mediatemple.net (216.70.104.17) 131.012 ms Looks to me like there is significant delay across the limelight network. This would explain why the traceroute via my rackspace server doesn't suffer from the same delay as they will be using their own trunk.

  Read the article

• USB mouse connecting and disconnecting randomly

  - by Kalec

  I've bought an acer aspire 5742G about 2 months ago or so and it's been running great, but sometimes I used to hear the windows error beep but I had no idea what was causing it since the "bug" was automatically fixed so fast I couldn't even see an error message (also it kinda always happened when I was busy also, either in a game or while doing my homework). Later on my mouse would simply not work for 3-5 seconds then work again, I thought nothing of it at the time. I also had a problem where it only worked in one usb and one only. To move it I had to remove the battery, unplug the laptop and hold the power button for 2 minutes to reset the bios settings. Since today though it went nuts. Sometimes it disconnects / reconnects 12 times in 10 seconds and windows just keeps beeping till I unplug it, then it runs smooth for 5-6 minutes then it goes nuts again. Other times it seems like it skips (disconnects for a fraction of a second) other times just for 2-3 seconds. But this is incredibly frustrating. Sometimes the power just goes down (the laser turns off) and well that at least I would understand but this is a rare occurrence. Now I know the usb ports work since I have a lot of other devices connected and I tried the mouse on a room m8's laptop so the mouse also works. My only conclusion is that it's an operating system / settings bug and / or problem (I have tried the mouse in all ports by the way). All drivers and bios are up to date (maybe except mouse but I can't seem to update that and the mouse has no name, just a serial number which helps with nothing. Still it worked till today and nothing should have changed any way). I have made sure windows can't shut it down to save power (in device management). Also I tried to delete the drivers and re-install them, rebooting and the power button trick but nothing. Most I have done is get rid of the 12 disconnects / reconnects every 10 seconds :) but that's all :( I would buy a new one but I'm afraid it might do the same thing. ****EDIT****** Tried the mouse again at a friend but now it didn't even install it's software nor did the update work. Think I'll just buy a new one but I'd still like a suggestion at least so I'll leave this open #### EDIT 2 Now it works again, I can't explain this. Still thinking of getting a new one though

  Read the article

• Proper Imaging Procedures to Restore and Deploy Image with Separate System Reserved Partition

  - by alharaka

  UPDATE: As per my experience here, no one responded. If I do not hear back from TechNet forum members about it, I will post a bounty here, if it makes a difference. I have banged my head against a wall for what seems like all week. I am going to explain my simple procedure, and how none of it, absolutely none, seems to work afterword despite few alternatives and everyone on the internet telling assuming this is how to do it. Diskpart Commands to Create FS Structure REM Select the disk targeted for deployment. REM REM NOTE: Usually disk 0, but drive failure can make it external USB REM media. This will erase the drive regardless! select disk 0 REM Remove previous formatting. clean REM Create System Reserved partition bootloader and files. create partition primary size=100 REM Format the volume format fs=ntfs label="System Reserved" quick override noerr REM Assign the System Reserved partition the D: mount for now assign letter=C REM The main system partition, size not specified to occupy whole drive. create partition primary REM Format the volume format fs=ntfs quick override noerr REM Assign the OS partition the D: mount for now assign letter=D REM Make this the active/bootable partition. sel disk 0 sel partition 1 active REM Close out the diskpart session. exit Now, I thought this was madness, but it turns out the System Reserved partition and standard "System Partition" (C:, commonly both the boot and system volumes where you find the Windows directory AND the bootmgr/ntldr hardware files, this is where Windows 7 diverges) as mounted in the Windows PE session where I run these commands do not matter. See reference here. Since this needs to be BitLocker-ready, enter this crappy System Reserved partition that is separate 100MB of awesome that goes before the regular boot volume. I do this, then I proceed to the next step. Deploy System Reserved and Normal System Images REM C is still the "System Reserved Partition", and the image is just like it sounds. imagex /apply G:\images\systemreserved.wim 1 C: REM D is now what will be the C: system partition on reboot, supposedly. imagex /apply G:\images\testimage.wim 1 D: Reboot the system Now, the images I just captured should look good. This is not even sysprepped, but reapplying the same fscking image I prepared on the same reference workstation hours before. Problem is I get 0xc000000e could not detect the accessible boot device \Windows\system32\winload.exe or different kinds of nonsense revolving around being able to find the boot volume with all the right files. I try different variations of things, now none of them work. I tried repairs with bcdboot, with a fresh System Reserved partition or not, bootrec, and maually editing the damn BCD store with bcdedit. I tried finalizing the above process with and without bootsect /nt60 C: /force. I need to wrap up and automate this procedure. What am I doing wrong that does not make the image happy, but really just miserable.

  Read the article

• Performance of Cluster Shared Volume file copy from SAN

  - by Sequenzia

  I am hoping someone can help me out with a strange issue. We are running a Microsoft Failover Cluster with Server 2008 R2 and an Equallogic PS4000 SAN. Our main configuration has 2 Dell Poweredge T710 Servers in the cluster. We have CSV and Quorm setup. The servers each have 10 Broadcom 1Gb NICs. Right now 4 of the NICS are on the iSCSI network for accessing the SAN. They use MPIO and the Dell HIT pack. We have 5 VMs running on each node and everything runs smooth. No noticeable performance issues or anything. From the SAN I can see the 4 iSCSI connections from each server to each volume (CSV and Quorm). Again, it seems to perform great. The problem I am running into is with backups. I have tried a few backup programs like backupchain and Veeam. The problem is both of them are very very slow to backup the VMs. For instance I have a 500GB (fixed disc) VHD that’s running on the cluster. It takes over 18 hours to backup that VHD and that’s with compression and depuping turned off which is supposed to be the fasted. We also have a separate server that is just for backups. It has a lot of directed attached storage. As part of the troubleshooting I decided to bring that server into the cluster as a node. It now has access to the CSV and can read from C:\clusterstorage\volume1 which is where our VHDs live. This backup server only has 2 NICs. 1 NIC is going to the iSCSI network and the other is just on the main network. It has Intel NICS in it without any sort of MPIO or teaming. So with the 3rd server now in the cluster I started doing some benchmarking. I have a test VHD that’s about 7GBs that’s stored in the CSV. I have tested file copying that VHD from all 3 servers to directed attached storage in the respective server. The 2 Dell servers that are the main nodes in the cluster (they house the VMs) are reading that file at about 20Mbs/Sec. Which at that rate is way to slow for the backups. The other server which only has 1 NIC to the SAN is reading at around 100Mbs/Sec. I spent a few hours on the phone with Dell today about this . We went through all kind of tests and he was pretty dumb founded. He really has no idea why that server with only 1 NIC is reading about 5 times as fast as the servers with 4 NICS and MPIO. We looked at the network utilization of the NICs while the file copy was going on. The servers with the 4 NICs had a small increase of activity during the file copy but they only went up to around 8-10% on all 4 NICs. The other server with the 1 NIC jumped up to over 80% during the file copy. I plan on doing some more testing after hours and calling Dell back tomorrow but I really am confused (and so is Dell’s support rep) why I cannot get faster file copy access to the CSV on those servers. Anyone have any input on this? Any feedback would be greatly appreciated. Thanks in advance.

  Read the article

• Powershell Exchange script returning inconsistent results - PS weirdness

  - by Ian

  Maybe someone can shed some light on a bit of Powershell weirdness I've come across and can't explain. This PS script returns a list of exchange databases, their sizes and the number of mailboxes in each one: Get-MailboxDatabase | Select Server, StorageGroupName, Name, @{Name="Size (GB)";Expression={$objitem = (Get-MailboxDatabase $_.Identity); $path = "`\`\" + $objitem.server + "`\" + $objItem.EdbFilePath.DriveName.Remove(1).ToString() + "$"+ $objItem.EdbFilePath.PathName.Remove(0,2); $size = ((Get-ChildItem $path).length)/1048576KB; [math]::round($size, 2)}}, @{Name="Size (MB)";Expression={$objitem = (Get-MailboxDatabase $_.Identity); $path = "`\`\" + $objitem.server + "`\" + $objItem.EdbFilePath.DriveName.Remove(1).ToString() + "$"+ $objItem.EdbFilePath.PathName.Remove(0,2); $size = ((Get-ChildItem $path).length)/1024KB; [math]::round($size, 2)}}, @{Name="No. Of Mbx";expression={(Get-Mailbox -Database $_.Identity | Measure-Object).Count}} | Format-table –AutoSize If I add a simple 'sort name' before the 'format-table' my resulting table contains blanks where the database sizes and number of mailboxes should appear (not zeros, blank empty space).... but only in some rows, not all rows. Some rows contain numbers! If I put the '|sort name| ' after the initial 'get-mailboxdatabase' it works fine. Whats even weirder is if I do the following: Execute the above command Add the sort before format-table Execute the new command Execute the initial command again What I see is different amounts in each of the three cases - all of which are incorrect. Yet 1 and 3 are the same command and the only difference with 2 is a sort. 1 and 3 should, at a minimum, return the same results. I get blanks where I should have MBs If I add the sort after the get-mailboxdatabase, it always returns identical results (as it should). Can anyone suggest an explanation as to what may be going on? If its of any help in reading the expression, I've reformatted it here to make it a bit more readable: Get-MailboxDatabase | Select Server, StorageGroupName, Name, @{Name="Size (GB)";Expression={ $objitem = (Get-MailboxDatabase $_.Identity); $path = "`\`\" + $objitem.server + "`\" + $objItem.EdbFilePath.DriveName.Remove(1).ToString() + "$" + $objItem.EdbFilePath.PathName.Remove(0,2); $size = ((Get-ChildItem $path).length)/1048576KB; [math]::round($size, 2) }}, @{Name="Size (MB)";Expression={ $objitem = (Get-MailboxDatabase $_.Identity); $path = "`\`\" + $objitem.server + "`\" + $objItem.EdbFilePath.DriveName.Remove(1).ToString() + "$" + $objItem.EdbFilePath.PathName.Remove(0,2); $size = ((Get-ChildItem $path).length)/1024KB; [math]::round($size, 2) }}, @{Name="No. Of Mbx";expression={ (Get-Mailbox -Database $_.Identity | Measure-Object).Count }} | Format-table –AutoSize

  Read the article

• Why are my httpd mpm_prefork processes being reaped so quickly?

  - by Dan Pritts

  We've got a system running RHEL6, x64. We are using a local installation of apache 2.2.22 from source. we serve primarily: mod_perl applications (with a local installation of perl 5.16.0) tomcat applications proxied with mod_jk Here is some context; the main question is below. All of this talks to an Oracle backend. We are having issues with Oracle becoming unresponsive. We think this is because we're hitting the maximum process limit in oracle. We've upped the process limit, but now we are hitting memory pressure on the oracle server. We have tons of oracle sessions sitting idle. I can trace a bunch of them back to the httpd processes. We have mod_perl's Apache::DBI start up a new connection to the database with each httpd child that's spawned. We are concerned that these are not always getting closed out properly when the httpd's exit...and the httpd's are exiting very frequently. I know that it would be good to modify the mod_perl applications to use some better form of db connection pooling; we plan to pursue that but would like to solve our immediate problem sooner. So here's the main question. We are using the prefork MPM. The apache child processes are lasting at most a few minutes. Log analysis shows that each one is serving fewer than 50 clients before exiting; the last request each child serves is OPTIONS * HTTP/1.0 on some sort of internal connection; I'm under the impression that this is a "ping" from the master process. I've adjusted the MPM config as follows. I didn't want to raise MinSpareServers too high, because, after all, i'm trying to minimize the number of sessions to oracle. MinSpareServers 5 MaxSpareServers 30 MaxClients 150 MaxRequestsPerChild 10000 Right now we're serving 250-300 requests per minute. We've got 21 httpd's running, the eldest (other than the master, owned by root) being 3 minutes old. This rate of reaping of the apache children really seems excessive. What could be causing it? Apache was built with: $ ./configure --prefix=/opt/apache --with-ssl=/usr/lib --enable-expires --enable-ext-filter --enable-info --enable-mime-magic --enable-rewrite --enable-so --enable-speling --enable-ssl --enable-usertrack --enable-proxy --enable-headers --enable-log-forensic Apache config info: % /opt/apache/bin/httpd -V Server version: Apache/2.2.22 (Unix) Server built: Jul 23 2012 22:30:13 Server's Module Magic Number: 20051115:30 Server loaded: APR 1.4.5, APR-Util 1.4.1 Compiled using: APR 1.4.5, APR-Util 1.4.1 Architecture: 64-bit Server MPM: Prefork threaded: no forked: yes (variable process count) Server compiled with.... -D APACHE_MPM_DIR="server/mpm/prefork" -D APR_HAS_SENDFILE -D APR_HAS_MMAP -D APR_HAVE_IPV6 (IPv4-mapped addresses enabled) -D APR_USE_SYSVSEM_SERIALIZE -D APR_USE_PTHREAD_SERIALIZE -D SINGLE_LISTEN_UNSERIALIZED_ACCEPT -D APR_HAS_OTHER_CHILD -D AP_HAVE_RELIABLE_PIPED_LOGS -D DYNAMIC_MODULE_LIMIT=128 -D HTTPD_ROOT="/opt/apache" -D SUEXEC_BIN="/opt/apache/bin/suexec" -D DEFAULT_PIDLOG="logs/httpd.pid" -D DEFAULT_SCOREBOARD="logs/apache_runtime_status" -D DEFAULT_LOCKFILE="logs/accept.lock" -D DEFAULT_ERRORLOG="logs/error_log" -D AP_TYPES_CONFIG_FILE="conf/mime.types" -D SERVER_CONFIG_FILE="conf/httpd.conf" modules are compiled into apache rather than shared libs: % /opt/apache/bin/httpd -l Compiled in modules: core.c mod_authn_file.c mod_authn_default.c mod_authz_host.c mod_authz_groupfile.c mod_authz_user.c mod_authz_default.c mod_auth_basic.c mod_ext_filter.c mod_include.c mod_filter.c mod_log_config.c mod_log_forensic.c mod_env.c mod_mime_magic.c mod_expires.c mod_headers.c mod_usertrack.c mod_setenvif.c mod_version.c mod_proxy.c mod_proxy_connect.c mod_proxy_ftp.c mod_proxy_http.c mod_proxy_scgi.c mod_proxy_ajp.c mod_proxy_balancer.c mod_ssl.c prefork.c http_core.c mod_mime.c mod_status.c mod_autoindex.c mod_asis.c mod_info.c mod_cgi.c mod_negotiation.c mod_dir.c mod_actions.c mod_speling.c mod_userdir.c mod_alias.c mod_rewrite.c mod_so.c One final note - the red hat httpd, apr, and perl packages are all installed, but ldd shows that none of those libraries are linked with the running httpd.

  Read the article

• Server Cabinet/Room Cooling

  - by user37226

  Hello all. I currently have two desktops and three servers in my office sitting on the floor (I know this is bad). With that many servers the ambient temperature in the room goes up quickly. I am located in Dallas, TX so during the winter, if the heat is kept low, it is not a problem, but during the summer it easily jumps the room +10 degrees. I have decided and found a free 42U server cabinet that a hosting company was throwing away to house all of these systems in. One server is in a rack mount case while the other four servers are housed in mid-tower cases. I have purchased shelves for each computer and plan to lay the towers side ways on these shelves (as replacing the cases costs a heck of a lot of money). I like the idea of housing all of these systems in the cabinet because it will save a lot of room and clean up all of the cabling currently laying all over the office floor. When putting this setup together over the next couple of weeks, I want to address issues with dust and cooling. The server cabinet has a fan on top, front plexiglass door and a rear metal door with vent wholes on the bottom. First the cooling issues. I know I am going to want to have cool air enter the bottom of the cabinet and exit the top. I do not want the room heating up though as this will make my work area hot and then make the servers warmer as the air eventually reenters the cabinet. I had an idea to fix this problem, but am unsure if it will work. I was thinking of taking flexible piping and adapting it to the back fans of the computer having the other end of the pipe at the top close to the cabinet's top mounted fan. I was then thinking of creating a duct around the top fan into the attic. Now I am very concerned that the attic will cause issues with this type of setup because during July/August time frame, the attic is easily 120 degrees F. I could also use the flexible pipe to take it to an attic exhaust vent if it would be better to vent it into the 100 degree air outside (at least there may be wind. The other option would be to buy a small portable air conditioner. This may be a possibility, but do I want to spend the extra money on power? I bet this increases the noise. Plus they are around $250 on Amazon. What would you all recommend? Depending on the solution I end up running with above, I would also like to limit the dust that gets into the cabinet. If I were to cut a whole and mount a second cabinet fan on the bottom of the rear door, could I possibly mount a standard home air filter on the other side of that whole? Thanks in advance for your recommendations. I look forward to reading your interesting ideas.

  Read the article

• Server Cabinet/Room Cooling

  - by user37226

  Hello all. I currently have two desktops and three servers in my office sitting on the floor (I know this is bad). With that many servers the ambient temperature in the room goes up quickly. I am located in Dallas, TX so during the winter, if the heat is kept low, it is not a problem, but during the summer it easily jumps the room +10 degrees. I have decided and found a free 42U server cabinet that a hosting company was throwing away to house all of these systems in. One server is in a rack mount case while the other four servers are housed in mid-tower cases. I have purchased shelves for each computer and plan to lay the towers side ways on these shelves (as replacing the cases costs a heck of a lot of money). I like the idea of housing all of these systems in the cabinet because it will save a lot of room and clean up all of the cabling currently laying all over the office floor. When putting this setup together over the next couple of weeks, I want to address issues with dust and cooling. The server cabinet has a fan on top, front plexiglass door and a rear metal door with vent wholes on the bottom. First the cooling issues. I know I am going to want to have cool air enter the bottom of the cabinet and exit the top. I do not want the room heating up though as this will make my work area hot and then make the servers warmer as the air eventually reenters the cabinet. I had an idea to fix this problem, but am unsure if it will work. I was thinking of taking flexible piping and adapting it to the back fans of the computer having the other end of the pipe at the top close to the cabinet's top mounted fan. I was then thinking of creating a duct around the top fan into the attic. Now I am very concerned that the attic will cause issues with this type of setup because during July/August time frame, the attic is easily 120 degrees F. I could also use the flexible pipe to take it to an attic exhaust vent if it would be better to vent it into the 100 degree air outside (at least there may be wind. The other option would be to buy a small portable air conditioner. This may be a possibility, but do I want to spend the extra money on power? I bet this increases the noise. Plus they are around $250 on Amazon. What would you all recommend? Depending on the solution I end up running with above, I would also like to limit the dust that gets into the cabinet. If I were to cut a whole and mount a second cabinet fan on the bottom of the rear door, could I possibly mount a standard home air filter on the other side of that whole? Thanks in advance for your recommendations. I look forward to reading your interesting ideas.

  Read the article

• Putting indexes in separate filegroup kills our queries

  - by womp

  Can anyone shed some light on this? On our dev boxes, our database resides entirely in the PRIMARY filegroup, and everything works fine. On one of our production servers, recently upgraded from 2005 to 2008, we noticed it was performing slower than it should. On this machine, there are two filegroups - PRIMARY and INDEXES. Both filegroups contain 1 file per logical volume, one logical volume per CPU, (and each logical volume is a RAID 10 of 4 physical disks). We isolated a few queries that were performing fast on the dev boxes and slow (up to 40x slower) on the production machine. Turned out these queries were using the non-clustered indexes that resided in the INDEXES filegroup. Tweaking some of the queries to only use clustered indexes that were in the PRIMARY filegroup dropped their times back to normal. As a final confirmation, we redeployed the same database on the same machine to have everything in PRIMARY, and things went back to normal! Here's the statistics output of one of the queries, run identically on the machine with different filegroup configurations (table names changed to protect the innocent): FAST (everything in PRIMARY filegroup): (3 row(s) affected) Table '0'. Scan count 2, logical reads 14, ... Table '1'. Scan count 0, logical reads 0, ... Table '1'. Scan count 0, logical reads 0, ... Table '2'. Scan count 2, logical reads 7, ... Table '3'. Scan count 2, logical reads 1012, ... Table '4'. Scan count 1, logical reads 3, ... SQL Server Execution Times: CPU time = 437 ms, elapsed time = 445 ms. SLOW (indexes split into their own filegroup): (3 row(s) affected) Table '0'. Scan count 209, logical reads 428, ... Table '1'. Scan count 0, logical reads 0,... Table '2'. Scan count 1021, logical reads 9043,.... Table '3'. Scan count 209, logical reads 105754, .... Table '4'. Scan count 0, logical reads 0, .... Table '5'. Scan count 1, logical reads 695, ... **Table '#46DA8CA9'. Scan count 205, logical reads 205, ...** Table '6'. Scan count 6, logical reads 436, ... Table '7'. Scan count 1, logical reads 12,.... SQL Server Execution Times: CPU time = 17581 ms, elapsed time = 17595 ms. Notice the weird temp table and extra tables involved in the slow query. It seems clear that having a second file group is making SQL Server batty with choosing an execution plan. What the heck is going on?

  Read the article

• Linux per-process resource limits - a deep Red Hat Mystery

  - by BobBanana

  I have my own multithreaded C program which scales in speed smoothly with the number of CPU cores.. I can run it with 1, 2, 3, etc threads and get linear speedup.. up to about 5.5x speed on a 6-core CPU on a Ubuntu Linux box. I had an opportunity to run the program on a very high end Sunfire x4450 with 4 quad-core Xeon processors, running Red Hat Enterprise Linux. I was eagerly anticipating seeing how fast the 16 cores could run my program with 16 threads.. But it runs at the same speed as just TWO threads! Much hair-pulling and debugging later, I see that my program really is creating all the threads, they really are running simultaneously, but the threads themselves are slower than they should be. 2 threads runs about 1.7x faster than 1, but 3, 4, 8, 10, 16 threads all run at just net 1.9x! I can see all the threads are running (not stalled or sleeping), they're just slow. To check that the HARDWARE wasn't at fault, I ran SIXTEEN copies of my program independently, simultaneously. They all ran at full speed. There really are 16 cores and they really do run at full speed and there really is enough RAM (in fact this machine has 64GB, and I only use 1GB per process). So, my question is if there's some OPERATING SYSTEM explanation, perhaps some per-process resource limit which automatically scales back thread scheduling to keep one process from hogging the machine. Clues are: My program does not access the disk or network. It's CPU limited. Its speed scales linearly on a single CPU box in Ubuntu Linux with a hexacore i7 for 1-6 threads. 6 threads is effectively 6x speedup. My program never runs faster than 2x speedup on this 16 core Sunfire Xeon box, for any number of threads from 2-16. Running 16 copies of my program single threaded runs perfectly, all 16 running at once at full speed. top shows 1600% of CPUs allocated. /proc/cpuinfo shows all 16 cores running at full 2.9GHz speed (not low frequency idle speed of 1.6GHz) There's 48GB of RAM free, it is not swapping. What's happening? Is there some process CPU limit policy? How could I measure it if so? What else could explain this behavior? Thanks for your ideas to solve this, the Great Xeon Slowdown Mystery of 2010!

  Read the article

• How Do I Restrict Repository Access via WebSVN?

  - by kaybenleroll

  I have multiple subversion repositories which are served up through Apache 2.2 and WebDAV. They are all located in a central place, and I used this debian-administration.org article as the basis (I dropped the use of the database authentication for a simple htpasswd file though). Since then, I have also started using WebSVN. My issue is that not all users on the system should be able to access the different repositories, and the default setup of WebSVN is to allow anyone who can authenticate. According to the WebSVN documentation, the best way around this is to use subversion's path access system, so I looked to create this, using the AuthzSVNAccessFile directive. When I do this though, I keep getting "403 Forbidden" messages. My files look like the following: I have default policy settings in a file: <Location /svn/> DAV svn SVNParentPath /var/lib/svn/repository Order deny,allow Deny from all </Location> Each repository gets a policy file like below: <Location /svn/sysadmin/> Include /var/lib/svn/conf/default_auth.conf AuthName "Repository for sysadmin" require user joebloggs jimsmith mickmurphy </Location> The default_auth.conf file contains this: SVNParentPath /var/lib/svn/repository AuthType basic AuthUserFile /var/lib/svn/conf/.dav_svn.passwd AuthzSVNAccessFile /var/lib/svn/conf/svnaccess.conf I am not fully sure why I need the second SVNParentPath in default_auth.conf, but I just added that today as I was getting error messages as a result of adding the AuthzSVNAccessFile directive. With a totally permissive access file [/] joebloggs = rw the system worked fine (and was essentially unchanged), but as I soon as I start trying to add any kind of restrictions such as [sysadmin:/] joebloggs = rw instead, I get the 'Permission denied' errors again. The log file entries are: [Thu May 28 10:40:17 2009] [error] [client 89.100.219.180] Access denied: 'joebloggs' GET websvn:/ [Thu May 28 10:40:20 2009] [error] [client 89.100.219.180] Access denied: 'joebloggs' GET svn:/sysadmin What do I need to do to get this to work? Have configured apache wrong, or is my understanding of the svnaccess.conf file incorrect? If I am going about this the wrong way, I have no particular attachment to my overall approach, so feel free to offer alternatives as well. UPDATE (20090528-1600): I attempted to implement this answer, but I still cannot get it to work properly. I know most of the configuration is correct, as I have added [/] joebloggs = rw at the start and 'joebloggs' then has all the correct access. When I try to go repository-specific though, doing something like [/] joebloggs = rw [sysadmin:/] mickmurphy = rw then I got a permission denied error for mickmurphy (joebloggs still works), with an error similar to what I already had previously [Thu May 28 10:40:20 2009] [error] [client 89.100.219.180] Access denied: 'mickmurphy' GET svn:/sysadmin Also, I forgot to explain previously that all my repositories are underneath /var/lib/svn/repository UPDATE (20090529-1245): Still no luck getting this to work, but all the signs seem to be pointing to the issue being with path-access control in subversion not working properly. My assumption is that I have not conf

  Read the article

• Windows 2008 IIS 7.0 HTTP to HTTPS Redirect -- Versus IIS 6.0 Mechanism

  - by Dan7el

  This topic, creating a mechanism for redirection from HTTP to HTTPS on a Windows 2008 server running IIS 7.0 is a much written-about topic on the Internet. How this is done is really not so much my issue. My issue is more of explaining why this can't be done with the standard HTTP Redirect module that ships with Windows 2008 IIS 7.0. Instead, there are other methods needed that are more arduous. First, the IIS 6.0 method requires no externally available modules nor does it require any additional modifications to the web.config or any type of other development effort. It's outlined here: http://blogs.microsoft.co.il/blogs/dorr/archive/2009/01/13/how-to-force-redirection-from-http-to-https-on-iis-6-0.aspx And, you can see the basic steps are to run the snap-in, get the properties on the site, and do some modifications. Presto, you have the HTTP -- HTTP redirect setup. Now, on the IIS 7.0 platform, it doesn't seem this simple. An initial search found the following site: http://www.sslshopper.com/iis7-redirect-http-to-https.html Which has two separate approcates: 1. Involves installing a separately available Microsoft module -- URL Rewrite Module, and then adding XML to the web.config. 2. Custom Error Page. ...there might be other methods, but these are the basic ones and the first is listed as the primary method. But wait...There exists on the IIS 7.0 an HTTP Redirect Module. So...why can't I use the HTTP Redirect Module to do this very thing? This is really my big question. I need to know this because my management is going to insist I use the HTTP Redirect Module and set up the HTTP to HTTPS redirect in a similar fashion to how we do in IIS 6.0. Can someone please explain to me, in clean, simple, easy to understand, terms that both I and my management can understand as to why I need to go get the URL Rewrite Module and install that on the server and make the web.config changes suggested by the article instead of simply using the HTTP Redirect module that's already installed on the site? Thanks a bunch.

  Read the article

• debian packages version convention

  - by JackWu

  I'm using debian/Ubuntu, and get confused about versions of packages. When using dpkg -l command, I get: ii vim 2:7.3.429-2ubuntu2.1 Vi IMproved - enhanced vi editor ii vim-common 2:7.3.429-2ubuntu2.1 Vi IMproved - Common files ii vim-runtime 2:7.3.429-2ubuntu2.1 Vi IMproved - Runtime files ii vim-tiny 2:7.3.429-2ubuntu2.1 Vi IMproved - enhanced vi editor - compact version ii virt-what 1.11-1 detect if we are running in a virtual machine ii w3m 0.5.3-5ubuntu1 WWW browsable pager with excellent tables/frames support ii watershed 6 reduce superfluous executions of idempotent command ii wget 1.13.4-2ubuntu1 retrieves files from the web ii whiptail 0.52.11-2ubuntu10 Displays user-friendly dialog boxes from shell scripts ii whoopsie 0.1.33 Ubuntu crash database submission daemon ii wimlib9 1.5.0-1~webupd8~precise Library to extract, create, modify, and mount WIM files ii wimtools 1.5.0-1~webupd8~precise Tools to extract, create, modify, and mount WIM files ii wireless-tools 30~pre9-5ubuntu2 Tools for manipulating Linux Wireless Extensions ii wpasupplicant 0.7.3-6ubuntu2.1 client support for WPA and WPA2 (IEEE 802.11i) ii x11-common 1:7.6+12ubuntu2 X Window System (X.Org) infrastructure ii x11-utils 7.6+4ubuntu0.1 X11 utilities ii xauth 1:1.0.6-1 X authentication utility ii xbitmaps 1.1.1-1 Base X bitmaps ii xclip 0.12-1 command line interface to X selections ii xfonts-encodings 1:1.0.4-1ubuntu1 Encodings for X.Org fonts ii xfonts-utils 1:7.6+1 X Window System font utility programs ii xkb-data 2.5-1ubuntu1.3 X Keyboard Extension (XKB) configuration data ii xml-core 0.13 XML infrastructure and XML catalog file support rc xpdf 3.02-21build1 Portable Document Format (PDF) reader ii xterm 271-1ubuntu2.1 X terminal emulator ii xz-lzma 5.1.1alpha+20110809-3 XZ-format compression utilities - compatibility commands ii xz-utils 5.1.1alpha+20110809-3 XZ-format compression utilities ii zabbix-agent 1:1.8.11-1 network monitoring solution - agent ii zlib1g 1:1.2.3.4.dfsg-3ubuntu4 compression library - runtime ii zlib1g-dev 1:1.2.3.4.dfsg-3ubuntu4 compression library - development ii zsh 4.3.17-1ubuntu1 shell with lots of features The third column is version, but it all messed up in a way I can't understand. I mean, different packages use total different naming specification. Here are the major questions: Why there are ubuntu in them, and there are not? what all the special -~+ mean? alpha and build, dfsg, what are they? Can I just use them casually? vim and other packages have 2:, what does that mean? How version comparison works, since they can be so different? Can anyone please explain this to me? Or where can I find an official document? Thanks in advance.

  Read the article

• Determining the required depth and specifications for a server cabinet

  - by Bingu Bingme

  I'm trying to understand the considerations ("why") that go into determining the specifications ("what") for a rackmount server cabinet, in order to determine what sort of rack I should purchase for my home use. Since this is for home use, I won't be following certain best practices (eg. hot/cold aisle, not even air conditioning) and may be willing to sacrifice in various areas in order to reduce cost and footprint - but please advise if there are safety concerns or other considerations to note. The most basic specs for a server cabinet are the dimensions (external width x external depth x usable height). Width: commonly 600mm or 800mm (if the use case requires extra clearance around the sides, such as if there is lots of cabling). In my case and most common cases, I'm going to stick with 600mm. Height: Select a sufficiently tall rack to fit my equipment. But how much may I stuff into it? Eg, if there is a 15U rack, can I really populate it with 15U of servers, or should I leave 1U at top and bottom for air circulation? Depth: Racks commonly have external depth of 600mm (network equipment), 800mm, 1000mm, or even longer. I'm trying to see how to fit into the 800mm depth. With reference to http://www.server-racks.com/rack-mount-depth.html, I'm hoping to have the front and rear posts mounted ~ 28.5" (72cm) apart, which would leave only 8cm for front space and rear space. How much rear space (from rear posts to back of rack) do I really need? I won't use cable management arms, so can I mount a 72cm depth server since the power, KVM, network cables won't take up much depth? My most important equipment are all < 60cm depth (4U chassis) and should comfortably fit within the 800mm cabinet. The rest of the equipment are very old 1U servers that range from 65-72cm depth. I might still want to make further use of them, or I might discard them since they are so old. Even if the 72cm servers cannot be powered on in an 800mm rack, I should be able to use them as 1U shelves. But, what server depth can I expect to be able to operate? Or am I forced to upgrade to 1000mm depth racks in order to use any servers deeper than 60cm? With reference to best practices for HP racks, some other specs and installation considerations: There aren't any minimum recommendations for clearance on the sides of the rack. It is recommended to leave 48" front clearance. The 48" front clearance is based on 32" chassis depth, 13" to extend the rack rails and mate the inner/outer rails, and 3" for movement. If I don't use such rails (eg, use shelves instead), it should be sufficient to leave front clearance of chassis depth + 3". It is recommended to leave 30" rear clearance "to provide space for servicing the rack". I'm planning to back the rack into a corner of the room, and wheel it slightly out when I need to access the rear. If the wheeling plan is ok, I still need to know how much rear clearance is required for air circulation and ventilation purposes. Castor wheels and stabilising feet. Since I'm backing the rack into a corner of the room, I'll only be able to set the stabilising feet on the front corners. Thoughts on safety? The rack that I'm considering has front glass doors with side ventilation slits and fully perforated rear doors. I'm hoping this will be a good balance between temperature and noise (only ventilation slits facing out the front, while the rear is facing the walls). Or is the sound of high-rpm fans going to escape through the front slits anyway and destroy my sanity?

  Read the article

• Operative systems on SD cards

  - by HisDudeness

  I was getting some wild ideas the last days, like putting some operative systems into SD cards rather than on my hard drive. I'll go further into details now and explain what lead me to consider this probably abominable decision. I am on a laptop (that means I have a native SD-card reader) which is currently running a cross-distro setup, with a bunch of Linux systems (placed in dedicated ext4 logical partitions into a huge extended one) regulated by an unique GRUB. Since today, my laptop haven't even seen any Windows system with binoculars. I was thinking about placing all the os part of my setup into a Secure Digital to save all my 500 Gb Hard Drive for documents, music, videos and so on, and being able to just remove the SD and boot my system into another computer too, as well as having the possibility of booting other systems into mine by just plugging in another SD, without having to keep it constantly placed in my PC. Also, in the remote case in the near future I just wanted to boot Windows 8 in it, I read it causes major boot incompatibility issues with other systems by needing a digital signature in order for them to start. By having it in a removable drive, I could just get rid of it when I'm needing him and switch its card with Linux one, and so not having any obstacles to their boot. Now, my questions are: I know unlikely traditional rotating disk drives, integrated circuits ones have a limited lifespan in terms of cluster rewriting. Is it an obstacle to that kind of usage? I mean, some Ultrabooks are using SSD now, is it the same issue, or there are some differences between Solid State Drives and Secure Digitals in that sense? Maybe having them to store system files which are in fixed positions (making the even-usage of cluster technology useless) constantly being re-read and updated and similar things just gets them soon unserviceable, do it? Second question: are all motherboards and BIOSes able to boot from SDs just like they are from USB pen drives (I mean, provided card reader is USB-connected, isn't it)? Or can't bootloaders like GRUB be installed on SDs working? If they can't, is it a solution installing GRUB to MBR and making boot option pointing to SD? Will it work? Are there any other problems to installing OSs on a Secure Digital?

  Read the article

• Old CRT screen's high resolution doesn't work anymore on windows 7

  - by Mixxiphoid

  One year ago I decided to switch from Windows XP to Windows 7. I had a 17" CRT monitor with a screen resolution of 1600x1200 which worked fine on Windows XP. While installing Windows 7 everything went well until Windows 7 was going to install the video card its driver. Windows 7 puts the screen to its recommended resolution and my screen became black. I waited a few minutes to be sure the installation was finished. I turned off the computer by hand and restarted the computer on a resolution of 800x640. When windows 7 was done installing I went to screen resolutions and the resolution of 1600x1200 was on the top of the list with '(recommended)' next to it. I tried putting it on 1600x1200 but again my screen went black. I installed all windows 7 updates including the video card driver from the NVidia site (NOT from Windows 7). I tried about everything to make it work on 1600x1200 but with no succes. The highest resolution I got with the crt monitor was 1280x1024. I had a TFT screen which had 1280x1024 as max resolution and had better colors, so I used that one till today. My video card is 9600GT and my power supply is beyond sufficient. I even tried to install the driver I had on XP to see if it worked, but no results. I tried classic mode on windows 7, changed the dpi, the frequentie and the monitor settings, but nothing worked. I really like a vertical resolution of 1200, but it seems today I'm bound to all those standard monitors with a resolution of 1980x1024... Can anybody explain to me what the cause is that it worked on Windows XP but not on Windows 7? And maybe a solution to the problem (I actually gave up on getting it fixed...) Thanks a lot in advance. SOLUTION I downloaded the according monitor driver and installed it. Next I rebooted my computer on low resolution (800x640) and connected the CRT monitor. When Windows 7 booted successfully I went to computer management and 'update the driver' of my monitor. I manually selected 'Generic PnP monitor' and made that one active. I want to advanced settings at 'Screen resolution' and selected the mode '1600x1200 (32-bit) 80 Hertz (95 Hertz did not work). Now I had my resolution on 1600x1200. I repeated the earlier step to select the original monitor again instead of the Generic monitor. Quite a way to solve this problem, but it worked! Thanks a lot you all.

  Read the article

• Symantec Protection Suite and System Recovery 2011 Desktop Edition

  - by rihatum

  I am re-posting this as my previous question was being treated as if I am "Shopping or seeking Product Recommendations" even though I was NOT - BTW they have deleted my comments too which were not offensive in nature. anyway - I have re-phrased some parts of my question and I hope SF Admins "Do Not Modify / Edit" this one - will be most grateful for that. I have a lot of respect for the People who visit this SITE and help others ! Just To clarify : Just to go by SF rules - I am not seeking someone to Design this solution, I am simply seeking real world examples, experiences, technical expert opinions / suggestions, any tips or tricks they may have or any problems they may have faced while doing something similar above with these products. I am also not asking for Capacity Planning for Storage, We have done some research and I am seeking Expert Assurance / Suggestions. We (our company) are planning to deploy Symantec Endpoint Protection and Symantec Desktop Recovery 2011 Desktop Edition to our 3000 - 4000 workstations (Windows7 32 and 64) with a few 100s with Windows XP 32/64 Bit. I have read the implementation guide for SEP and have read tech-notes for Desktop Recovery 2011. Our team have planned to deploy this as follows : 1 x dedicated SQL 2008R2 for Symantec Endpoint Protection (Instead of using the Embedded Database) 1 x Dedicated SQL 2008R2 for Symantec Desktop Recovery 2011 (Instead of using the Embedded Database) 1 x Dedicated W2K8 R2 Box for the SEPM (Symantec Endpoint Protection Manager - Mgmt. APP) 1 x Dedicated W2K8 R2 Box for the Symantec Desktop Recovery 2011 Management Application Agent Deployment : As per Symantec Documentation for both of the above, an agent can be pushed via the Mgmt. Application (provided no firewalls are blocking ports required etc. - we have Windows firewall disabled already). Server Hardware : Per SQL Server : 16GB RAM + SAS DISKS + Dual XEON, RAID-10 for the SQL DB or I can always mount a LUN from our existing Hitachi or EMC SAN. SEPM Server : 16GB RAM + SAS DISKS + DUAL XEON System Recovery MGMT SERVER : 16GB RAM + SAS DISKS + DUAL XEON Above is the initial plan we have for 3000 - 4000 client workstation (Windows) Now my Questions :-) a) If we had these users distributed amongst two sites with AD DC / GC in each site, How would I restrict SEPM and Desktop Mgmt. solution to only check for users in their respective site ? b) At present all users are under one building but we are going to move some dept. to a new location (with dedicated connectivity), How would we control which SEPM / MGMT Server is responsible for which site ? c) We have netbackup in our environment backing up other servers, I am planning to protect these 4 (2 x SQL, 1 x SEPM, 1 x System Recovery Mgmt. Server) via netbackup or I can use System recovery 2011 server edition on all 4 of these boxes as well. (License is not an issue as we have the complete symantec portfolio included in our license). d) Now - Saving Desktop backups - What strategies have you implemented ? Any best practice recommendation for a large user base ? I was thinking to either mount a LUN from our Hitachi SAN on the Symantec Recovery Server itself or backup to the users hard drive locally and then copy it over to a network location ? Suggestions welcome :-) If you have anything to add / correct - that will be really helpful before diving into the actual implementation phase. Will be most grateful with your suggestions, recommendations and corrections with above - Many Thanks !

  Read the article

• mac + parallels and https site test = router restarts

  - by Erik

  Ok I have an interesting & very frustrating problem happening. I'm going to explain it the best I can. I work as a graphic designer & web designer on a mac and have a Comcast internet connection that comes through a Comcast branded router (SMC8014) which then ties into an Airport Extreme Base Station which runs my office network. I run OS 10.5.7 and also run Parallels 4.0.3 (running Windows XP) for testing websites in Internet Explorer and so on. Ok, so that the basic background. Here's my issue. I've been collaborating an ecommerce website with another designer/developer and when testing the site on the PC side we have started to run into some sort of network problem. The site is https if that matters at all I suspect it may. Basically when I run parallels for testing I am constantly having to restart the router in order to connect to the test site (it's hosted). Funny thing is I can access the rest of the internet fine, just not this site I'm working on until I restart the router (It's sorta like the site is timing out). This never happens when just running the Mac side of things. It only becomes an issue when Parallels is open and I am doing page refreshes while making css or HTML edits via something like Coda or CSS edit (connected to the hosting server via ftp). The real problem is that once the problem starts I only get about 2 or 3 page loads before I have to restart the router again. It's absolutely crippling. I cannot get any work done when I have to restart the router every couple of minutes. So, if you think this problem is isolated to me, the answer is no. The designer/developer I'm collaborating with has an office a couple miles away and experiences very similar problems under slightly different setup. He also has Comcast as his internet provider and connects his router to an Airport and primarily works on a mac. The main difference is that rather than using a visualizer like parallels to test the website on the PC he uses a real live PC that is on his network. Once he fire up the PC to do testing he runs into the same issue described above. After a couple of page refreshes in Internet Explorer or other browser on the PC the site becomes unresponsive and the router has to get restarted. Any thoughts on what is going on here would be greatly appreciated. Thanks in advance.

  Read the article

• RAID controller dropping the wrong drive

  - by bramp

  I've been having an issue with 3ware 9500S-8 RAID 10, and I have contracted their tech support, but I wanted to hear the serverfault community's recommendations. Firstly, all my data is backuped and secure, so I don't mind blowing my RAID away if I have to. But let me describe the problem I've been seeing. A month ago, disk 6 dropped out of the RAID. It is mirrored with disk 7, so I wasn't that bothered. I went to the data centre and replaced it. When I got back to the office, I noticed that disk 6 will still not in the RAID, and in fact the controller was show the name of the old drive still. A week later I went back and replace the drive again, thinking I might have swapped in a bad drive. Still the same problem. I decided to reboot the machine, to see if that would "force" the controller into seeing the new drive. It did, and a rebuild started to happen (from disk 7). Eventually both drives were showing as good. A week later, the MySQL database has flagged the database is corrupt, and is unable to repair it. I don't know what has gone wrong, but I suspected this 6-7 pair. At this point I noticed that the RAID had constantly been verifying itself, over and over. Regardless of this I began to rebuild the database, which took about 19 hours. It's a big database. Near the end of the repair, the RAID controller told me it had dropped disk 7, and that some data was most likely corrupted. I contacted LSI tech support, and they very promptly started to help me. I mentioned that drive 7 had been dropped. They suspect that drive 7 was always at fault, and drive 6 had always been good. I want to know how often a RAID controller would drop the wrong drive (in this case dropping drive 6 a month ago, instead of 7). I foolishly didn't run smartctl on the drives before I started swapping them out. I just assumed the RAID controller knew what it was talking about. I think my plan of action is to replace drive 7, rebuild the array from scratch, double check smartctl on ALL the disks, and then start restoring my data again. I would appreciate anyone's input on what the correct procedure for swapping drives is, and how often failures like this happen. If anyone would like more information then I'd be happy to provide it. thanks in advance. Oh some more information. I'm running CentOS 5.3, with two RAID arrays, a simple RAID 1 for the OS, and RAID 10 for the database. Both arrays are on different controllers. The RAID 10 is made of 10 identical ST3640323AS drives, until I swapped in a SAMSUNG HD103SJ last month.

  Read the article

• Thunderbird 3: can't change column width?

  - by rumtscho

  I recently installed Thunderbird 3.0.3. Just noticed a suboptimal UI setting: in the upper pane, which lists the e-mails in the current folder, the Date column is about 200px wide. So when I keep the window at 480x600, all I see in a row is: | tree icon | favourites icon | attachment icon | read icon | junk icon | Date and time, followed by 5cm whitespace | ... | P Where "P" is the first letter of the name of the sender. And the "..." is actually shown this way, I have no idea which column it is meant to be. But I don't see neither the sender, nor the message subject, which makes scrolling a folder for a certain mail rather pointless. I see these when I maximize the window, actually the columns are then not only bigger, they are arranged in another sequence. But I feel that holding a mail client permanently maximised at 1600x1200 is a waste of screen real estate. My naive solution attempt was to try to go with the mouse cursor to the right edge of the date column and try to shrink it by moving the cursor left while holding down the left mouse button. Not only is this default behaviour for all resizable columns I've ever encountered in GUIs, the cursor actually turns into a horizontal double-headed arrow. But pulling has no effect at all. I cannot make a wide column narrow, and I cannot make the narrow columns wide. I didn't find anything in the preferences either. So can please somebody explain how to get the columns arranged sensibly? Edit: I found out that I only have the problem when I drag the Thunderbird window to a GridMove screen area. It gets automatically resized, but doesn't notice the resize event or something, so the column width remains the same as under a maximized window. First making the window narrow using the mouse helps with column width, but the width of the mail pane is still too wide (rows don't reflow). Anyway, this seems to be a bug caused by the combination of the two applications and not a configuration problem, so I guess I'll have to live with it.

  Read the article

< Previous Page | 392 393 394 395 396 397 398 399 400 401 402 403  | Next Page >