Search Results

Search found 23890 results on 956 pages for 'issue'.

Page 396/956 | < Previous Page | 392 393 394 395 396 397 398 399 400 401 402 403  | Next Page >

• Did a recent WinXP update break CD/DVD read speeds? SP2/SP3

  - by quack quixote

  I have two systems with fresh installations of Windows XP Pro SP3 (SP3 slipstreamed into the installer; fully updated after install). One's a refurbished 2.4GHz Pentium4 system; the other is a new 1.6GHz Atom330 build. Both have brand-new dual-layer CD/DVD burners (one's a LiteOn IDE, the other an LG SATA). Both take a really looooong time to read a single-layer DVD in Windows with Cygwin tools. Specifically, 40 minutes or more. I burn backup data to single-layer DVD+/-R and use MD5 hashes for data verification (made with the standard md5sum tool in Unix or Cygwin). The hashes are burned to disc with the data files, and I use this command to verify: $ cd /path/to/disc/mountpoint ; time md5sum -c < md5.txt Here's how long that takes to run on a full single-layer DVD+/-R disc: Old system (WinXP SP2, 1.8GHz Athlon 2500+, last summer): ~10 minutes Old system (Ubuntu 9.04, 1.8GHz Athlon 2500+): ~10 minutes Old system (Debian 5, dual 550MHz P3): ~10 minutes New Pentium4 system (running Ubuntu 9.04): ~5 minutes New Pentium4 system (running WinXP SP3, file copy from Win Explorer): ~6 minutes New Atom330 system (running WinXP SP3, file copy from Win Explorer): ~6 minutes Now the weird stuff: Old system (WinXP SP2, 1.8GHz Athlon 2500+, today): ~25 minutes New Pentium4 system (running WinXP SP3, read from Cygwin): ~40-50 minutes (?!!) New Atom330 system (running WinXP SP3, read from Cygwin): ~40 minutes (can do it in ~30 minutes ...if i have another program spin up the drive first) Since both systems will copy files in 6 minutes using Windows Explorer, I know it's not a hardware problem. Windows just never spins up the drive during the Cygwin read, so it stays super-slow the whole time. Other programs like EAC and DVD Decrypter seem to spin up the disc just fine during their processing. DMA is enabled on both systems. (Can confirm in Windows' Device Manager on the Atom330, not on the P4.) Nero's DriveSpeed tool doesn't seem to have any effect. Copy times are comparable from commandline with Windows' xcopy. Copying with Cygwin's cp looks more like the problem state -- it will spin up the drive for a short time, never reaches full speed, and lets it spin back down again for most of the copy. What I need is to get full read speeds from Cygwin. Is this a known issue with SP3 or some other recent Windows update? Any other ideas? Update: More testing; Windows will spin up the drive when data is copied with Windows tools, but not when read in place or copied with Cygwin tools. It doesn't make sense to me that Windows spins up the drive for copying, but not for other reads. Might be more of a Cygwin problem? Update 2: GUI activity is sluggish during the problem state -- during the Cygwin verifies, there's a slight but noticable delay when dragging windows or icons around on the desktop, switching windows, Alt-Tabbing through open applications, opening new windows, etc. It reminds me of the delay when opening a Windows Explorer window on My Computer just after inserting a DVD. I've tried updating Cygwin (from 1.5.x to 1.7.x), but no change in the problem behavior. I've also noticed this issue occurs on WinXP SP2, but it's not exactly the same -- some spin-up occurs, so the read happens in ~25-30 minutes instead of 40+. The SP2 system used to run the verifies in ~10 minutes, and when it first changed (not sure exactly when, maybe in late November or early December 2009) I thought it was dying hardware. This is why I suspect an official update of breaking this functionality; this has worked for years on that SP2 box.

  Read the article

• Routing not working correctly using the laravel framework

  - by samayres1992

  I'm using the book wrote by one of the guys that created laravel, so I'd like to think for the most part this code isn't horribly wrong. My server is setup with nginx serving all static files and apache2 serving php. My config for each are the following: apache2: <VirtualHost *> # Host that will serve this project. ServerName litl.it # The location of our projects public directory. DocumentRoot /var/www/litl.it/laravel/public # Useful logs for debug. CustomLog /var/log/apache.access.log common ErrorLog /var/log/apache.error.log # Rewrites for pretty URLs, better not to rely on .htaccess. <Directory /var/www/litl.it/laravel/public> <IfModule mod_rewrite.c> Options -MultiViews RewriteEngine On RewriteCond %{REQUEST_FILENAME} !-f RewriteRule ^ index.php [L] </IfModule> </Directory> nginx: server { # Port that the web server will listen on. listen 80; # Host that will serve this project. server_name litl.it *.litl.it; # Useful logs for debug. access_log /var/log/nginx.access.log; error_log /var/log/nginx.error.log; rewrite_log on; # The location of our projects public directory. root /var/www/litl.it/laravel/public; # Point index to the Laravel front controller. index index.php; location / { # URLs to attempt, including pretty ones. try_files $uri $uri/ /index.php?$query_string; } # Remove trailing slash to please routing system. if (!-d $request_filename) { rewrite ^/(.+)/$ /$1 permanent; } # PHP FPM configuration. location ~* \.php$ { proxy_pass http://127.0.0.1:8080; include /etc/nginx/proxy_params; try_files index index.php $uri =404; include /etc/nginx/fastcgi_params; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root/php/$fastcgi_script_name; } # We don't need .ht files with nginx. location ~ /\.ht { deny all; } location @proxy { proxy_pass http://127.0.0.1:8080; include /etc/nginx/proxy_params; } error_page 403 /error/403.html; error_page 404 /error/404.html; error_page 405 /error/405.html; error_page 500 501 502 503 504 /error/5xx.html; location ^~ /error/ { internal; root /var/www/litl.it/lavarel/public/error; } } I'm including these server configs, as I feel this maybe the issue? Here is my incredibly basic routing file that should return "routing is working" on domain.com/test but instead it just returns the homepage. <?php Route::get('/', function() { return View::make('hello'); }); Route::get('/test', function() { return "routing is working"; }); Any ideas where I'm going wrong, I'm following this tutorial very closely and I'm confused why there is issue. Thanks!

  Read the article

• Trouble getting SSL to work with django + nginx + wsgi

  - by Kevin

  I've followed a couple of examples for Django + nginx + wsgi + ssl, but I can't get them to work. I simply get an error in my browser than I can't connect. I'm running two websites off the host. The config files are identical except for the ip addresses, server names, and directories. When neither use SSL, they work fine. When I try to listen on 443 with one of them, I can't connect to either. My config files are below, and any suggestions would be appreciated. server{ listen xxx.xxx.xxx.xxx:80; server_name sub.domain.com; access_log /home/django/logs/nginx_customerdb_http_access.log; error_log /home/django/logs/nginx_customerdb_http_error.log; location / { proxy_pass http://127.0.0.1:8080; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; client_max_body_size 10m; client_body_buffer_size 128k; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 90; proxy_buffers 32 4k; } location /site_media/ { alias /home/django/customerdb_site_media/; } location /admin-media/ { alias /home/django/django_admin_media/; } } server{ listen xxx.xxx.xxx.xxx:443; server_name sub.domain.com; access_log /home/django/logs/nginx_customerdb_http_access.log; error_log /home/django/logs/nginx_customerdb_http_error.log; ssl on; ssl_certificate sub.domain.com.crt; ssl_certificate_key sub.domain.com.key; ssl_prefer_server_ciphers on; location / { proxy_pass http://127.0.0.1:8080; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header X-Forwarded-Protocol https; client_max_body_size 10m; client_body_buffer_size 128k; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 90; proxy_buffers 32 4k; } location /site_media/ { alias /home/django/customerdb_site_media/; } location /admin-media/ { alias /home/django/django_admin_media/; } } <VirtualHost *:8080> ServerName xxx.xxx.xxx.xxx ServerAlias xxx.xxx.xxx.xxx LogLevel warn ErrorLog /home/django/logs/apache_customerdb_error.log CustomLog /home/django/logs/apache_customerdb_access.log combined WSGIScriptAlias / /home/django/customerdb/apache/django.wsgi WSGIDaemonProcess customerdb_wsgi processes=4 threads=5 WSGIProcessGroup customerdb_wsgi SetEnvIf X-Forwarded-Protocol "^https$" HTTPS=on </VirtualHost> UDPATE: the existence of two sites (on separate IPs) on the host is the issue. if i delete the other site, the setting above mostly work. doing so also brings up another issue: chrome doesn't accept the site as secure saying that some content is not encrypted.

  Read the article

• conflict in debian packages

  - by Alaa Alomari

  I have Debian 4 server (i know it is very old) cat /etc/issue Debian GNU/Linux 4.0 \n \l I have the following in /etc/apt/sources.list deb http://debian.uchicago.edu/debian/ stable main deb http://ftp.debian.org/debian/ stable main deb-src http://ftp.debian.org/debian/ stable main deb http://security.debian.org/ stable/updates main apt-get upgrade Reading package lists... Done Building dependency tree... Done You might want to run 'apt-get -f install' to correct these. The following packages have unmet dependencies. libt1-5: Depends: libc6 (= 2.7) but 2.3.6.ds1-13etch10+b1 is installed locales: Depends: glibc-2.11-1 but it is not installable E: Unmet dependencies. Try using -f. Now it shows that i have Debian 6!! cat /etc/issue Debian GNU/Linux 6.0 \n \l EDIT I have tried apt-get update Get: 1 http://debian.uchicago.edu stable Release.gpg [1672B] Hit http://debian.uchicago.edu stable Release Ign http://debian.uchicago.edu stable/main Packages/DiffIndex Hit http://debian.uchicago.edu stable/main Packages Get: 2 http://security.debian.org stable/updates Release.gpg [836B] Hit http://security.debian.org stable/updates Release Get: 3 http://ftp.debian.org stable Release.gpg [1672B] Ign http://security.debian.org stable/updates/main Packages/DiffIndex Hit http://security.debian.org stable/updates/main Packages Hit http://ftp.debian.org stable Release Ign http://ftp.debian.org stable/main Packages/DiffIndex Ign http://ftp.debian.org stable/main Sources/DiffIndex Hit http://ftp.debian.org stable/main Packages Hit http://ftp.debian.org stable/main Sources Fetched 3B in 0s (3B/s) Reading package lists... Done apt-get dist-upgrade Reading package lists... Done Building dependency tree... Done You might want to run 'apt-get -f install' to correct these. The following packages have unmet dependencies. libt1-5: Depends: libc6 (= 2.7) but 2.3.6.ds1-13etch10+b1 is installed locales: Depends: glibc-2.11-1 E: Unmet dependencies. Try using -f. apt-get -f install Reading package lists... Done Building dependency tree... Done Correcting dependencies...Done The following extra packages will be installed: gcc-4.4-base libbsd-dev libbsd0 libc-bin libc-dev-bin libc6 Suggested packages: glibc-doc Recommended packages: libc6-i686 The following packages will be REMOVED libc6-dev libedit-dev libexpat1-dev libgcrypt11-dev libjpeg62-dev libmcal0-dev libmhash-dev libncurses5-dev libpam0g-dev libsablot0-dev libtool libttf-dev The following NEW packages will be installed gcc-4.4-base libbsd-dev libbsd0 libc-bin libc-dev-bin The following packages will be upgraded: libc6 1 upgraded, 5 newly installed, 12 to remove and 349 not upgraded. 7 not fully installed or removed. Need to get 0B/5050kB of archives. After unpacking 23.1MB disk space will be freed. Do you want to continue [Y/n]? y Preconfiguring packages ... dpkg: regarding .../libc-bin_2.11.3-2_i386.deb containing libc-bin: package uses Breaks; not supported in this dpkg dpkg: error processing /var/cache/apt/archives/libc-bin_2.11.3-2_i386.deb (--unpack): unsupported dependency problem - not installing libc-bin Errors were encountered while processing: /var/cache/apt/archives/libc-bin_2.11.3-2_i386.deb E: Sub-process /usr/bin/dpkg returned an error code (1) Now: it seems there is a conflict!! how can i fix it? and is it true that the server has became debian 6!!?? Thanks for your help

  Read the article

• Windows 7 sometimes boots in VGA mode

  - by TuxRug

  I have an Asus G50VT-x5 laptop with nVidia GeForce9800M-GS graphics. Normally, Windows boots normally, but about 20% of the time (rough estimate), it will boot with the fallback VGA driver, maxing out at 800x600 with no Aero. I've checked the system logs and there is nothing indicating an error loading the nVidia driver. It even specifies in the logs that the Nvidia Display Driver service started successfully, even though it has booted in safe graphics mode. This has been happening for a while, but it's happening a little more often now than it was before. Since the first time my system exhibited this behavior, I have updated my graphics driver a handful of times. I used System Information for Windows to check for problems there, but the only thing that stood out was the following: Core Temperature 4486449 °C (8075639 °F) Shaders Temperature 1171513530 °C (2108724330 °F) I know this reading is incorrect, because my laptop is nowhere near the surface of the sun and my desk has not burst into flames. When it's opererating normally, I get a sane reading like [Core Temperature 58 °C (136 °F)] with no Shaders Temperature listed. All I have to do to resolve the issue is reboot. I have seen no stability issues with the graphics or anything else. A long time ago, I had an issue with this computer where my framerate would suddenly drop during a 3D game from 40fps to <1fps, but after looking at the temperature readout immediately after quitting a game, I removed the bottom panel and blew the dust out of the vent and heatsink. Since then I have no drops in framerate under any situation. I have uploaded a zip containing the SIW reports for when the problem is occurring and when the computer is operating normally. I don't have a paid account so it can only be downloaded 10 times, so please only download the reports if you think you can use them. If you try to download the reports and they are no longer available, please comment and I will re-upload them. If you want to look at the files, they are on Rapidshare. EDIT It happened again, and I looked a little deeper into the System logs. When this happens, there are a lot of errors about other device drivers unable to start. All of these errors are for PnP drivers. Also, my USB keyboard and mouse take a few moments before they actually start working, although this happens sometimes the first normal boot as well. I am quite sure this is related, so I am adding the pnp tag. Also, CHKDSK will not run on boot. Even if a check is scheduled or a volume is manually set as dirty, CHKDSK will be skipped entirely, not even leaving an entry in the System logs. I tried running CHKNTFS /D, which did not work. I then manually changed my HKLM\System\CurrentControlSet\Control\Session Manager BootExecute value to the default listed on Microsoft's website. That did not work either. I ended up booting to repair mode and running CHKDSK there, which found a number of minor inconsistencies on my system drive, but none on my data drive. I have no idea if this is related. Some more information for those who don't download my SIW report file: Antivirus and Firewall are ESET Smart Security I have three different virutalization programs installed: VMware Player, Windows Virtual PC, and VirtualBox. The network adapters for these show up in the log of failed device starts. EDIT 2 I tried running sfc /scannow, which reported that it found corrupted files that could not be fixed. The CBS log is extremely cryptic. I tried booting to my install disk, launching repair mode, and doing an offline sfc from there, which produced the same result.

  Read the article

• Motion - can't get streaming working from a webcam

  - by Emmanuel Brunet

  I'm trying to record a video stream from my Tenvis IP camera with motion 3.2.12 on Debian 7.5. I used the standard debian package with sudo apt-get install motion Assume my DNS IP cam is webcam, user : admin, password : password /etc/motion/motion.conf Bellow are my configuration file settings : netcam_url http://webcam/videostream.cgi netcam_userpass admin:password target_dir /media/videos/log/motion # The mini-http server listens to this port for requests (default: 0 = disabled) webcam_port 1234 ffmpeg_cap_new on ffmpeg_video_codec mpeg4 output_motion off snapshot_interval 0 # Quality of the jpeg (in percent) images produced (default: 50) webcam_quality 50 # Output frames at 1 fps when no motion is detected and increase to the # rate given by webcam_maxrate when motion is detected (default: off) webcam_motion on # Maximum framerate for webcam streams (default: 1) webcam_maxrate 15 # Restrict webcam connections to localhost only (default: on) webcam_localhost on # Limits the number of images per connection (default: 0 = unlimited) # Number can be defined by multiplying actual webcam rate by desired number of seconds # Actual webcam rate is the smallest of the numbers framerate and webcam_maxrate webcam_limit 0 control_port 8080 control_authentication admin:password Issue #1 when I try display http:/localhost:1234 the browser looks frozen, no HTTP 404 received but it stills waiting for data it seems .. Issue #2 in the output directory motion writes a lot of jpeg snapshots althought I just want to have several video sequenced files. Log I run motion in interactive mode in a terminal, here is the ouput root@mercure:/etc/motion# motion -c motion-1.0.conf [0] Processing thread 0 - config file motion-1.0.conf [0] Motion 3.2.12 Started [0] ffmpeg LIBAVCODEC_BUILD 3482368 LIBAVFORMAT_BUILD 3478785 [0] Thread 1 is from motion-1.0.conf [0] motion-httpd/3.2.12 running, accepting connections [0] motion-httpd: waiting for data on port TCP 8080 [1] Thread 1 started [1] Resizing pre_capture buffer to 1 items [1] Started stream webcam server in port 1234 [1] avcodec_open - could not open codec: Operation now in progress [1] ffopen_open error creating (new) file [~/tmp/motion/01-20140603165303.avi]: Operation now in progress [1] File of type 1 saved to: ~/tmp/motion/01-20140603165303-01.jpg [1] Thread exiting [1] Calling vid_close() from motion_cleanup [1] vid_close: calling netcam_cleanup [1] netcam camera handler: finish set, exiting [0] Motion thread 1 restart [1] Thread 1 started [1] Resizing pre_capture buffer to 1 items [1] Started stream webcam server in port 1234 [1] avcodec_open - could not open codec: Resource temporarily unavailable [1] ffopen_open error creating (new) file [~/tmp/motion/01-20140603165329.avi]: Resource temporarily unavailable [1] File of type 1 saved to: ~/tmp/motion/01-20140603165329-00.jpg [1] Thread exiting [1] Calling vid_close() from motion_cleanup [1] vid_close: calling netcam_cleanup [1] netcam camera handler: finish set, exiting [0] Motion thread 1 restart [1] Thread 1 started [1] Resizing pre_capture buffer to 1 items [1] Started stream webcam server in port 1234 [1] avcodec_open - could not open codec: Connection reset by peer [1] ffopen_open error creating (new) file [~/tmp/motion/01-20140603165355.avi]: Connection reset by peer [1] File of type 1 saved to: ~/tmp/motion/01-20140603165355-06.jpg [1] Thread exiting [1] Calling vid_close() from motion_cleanup [1] vid_close: calling netcam_cleanup [0] httpd - Finishing [0] httpd Closing [0] httpd thread exit [1] netcam camera handler: finish set, exiting [0] Motion thread 1 restart [1] Thread 1 started [1] Resizing pre_capture buffer to 1 items [1] Started stream webcam server in port 1234 It doesn't find the codec ... avcodec_open - could not open codec: Operation now in progress I've changed fmpeg_video_codec from mpeg4 to swf the result is the same. When using flv format motion writes a lot of .jpg image but I can't see anything at http://localhost:1234 [1] File of type 1 saved to: ~/tmp/motion/01-20140603171035-00.jpg [1] File of type 1 saved to: ~/tmp/motion/01-20140603171035-01.jpg [1] File of type 1 saved to: ~/tmp/motion/01-20140603171035-02.jpg [1] File of type 1 saved to: ~/tmp/motion/01-20140603171035-03.jpg [1] File of type 1 saved to: ~/tmp/motion/01-20140603171035-04.jpg [1] File of type 1 saved to: ~/tmp/motion/01-20140603171035-05.jpg [1] File of type 1 saved to: ~/tmp/motion/01-20140603171035-06.jpg [1] File of type 1 saved to: ~/tmp/motion/01-20140603171036-00.jpg [1] File of type 1 saved to: ~/tmp/motion/01-20140603171036-01.jpg [1] File of type 1 saved to: ~/tmp/motion/01-20140603171036-02.jpg Any idea just to get the video stream recoded on my local disk ?

  Read the article

• PHP.ini does not load

  - by Jonathan Park

  Ok this is probably just me not knowing enough about php but here it goes. I'm on Ubuntu Hardy. I have a custom compiled version of PHP which I have compiled with these parameters. ./configure --enable-soap --with-zlib --with-mysql --with-apxs2=[correct path] --with-config-file-path=[correct path] --with-mysqli --with-curlwrappers --with-curl --with-mcrypt I have used the command pecl install pecl_http to install the http.so extension. It is in the correct module directory for my php.ini. My php.ini is loading and I can change things within the ini and effect php. I have included the extension=http.so line in my php.ini. That worked fine. Until I added these compilation options in order to add imap --with-openssl --with-kerberos --with-imap --with-imap-ssl Which failed because I needed the c-client library which I fixed by apt-get install libc-client-dev After which php compiles fine and I have working imap support, woo. HOWEVER, now all my calls to HttpRequest which is part of the pecl_http extention in http.so result in Fatal error: Class 'HttpRequest' not found errors. I figure the http.so module is no longer loading for one reason or another but I cannot find any errors showing the reason. You might say "Have you tried undoing the new imap setup?" To which I will answer. Yes I have. I directly undid all my config changes and uninstalled the c-client library and I still can't get it to work. I thought that's weird... I have made no changes that would have resulted in this issue. After looking at that I have also discovered that not only is the http extension no longer loading but all my extensions loaded via php.ini are no longer loading. Can someone at least give me some further debugging steps? So far I have tried enabling all errors including startup errors in my php.ini which works for other errors, but I'm not seeing any startup errors either on command line or via apache. And yet again the php.ini appears to be being parsed given that if I run php_info() I get settings that are in the php.ini. Edit it appears that only some of the php.ini settings are being listened to. Is there a way to test my php.ini? Edit Edit It appears I am mistaken again and the php.ini is not being loaded at all any longer. However, If I run php_info() I get that it's looking for my php.ini in the correct location. Edit Edit Edit My config is at the config file path location below but it says no config file loaded. WTF Permission issue? It is currently 644 so everyone should be able to read it if not write it. I tried making it 777 and that didn't work. Configuration File (php.ini) Path /etc/php.ini Loaded Configuration File (none) Edit Edit Edit Edit By loading the ini on the command line using the -c command I am able to run my files and using -m shows that my modules load So nothing is wrong with the php.ini

  Read the article

• RHCS: GFS2 in A/A cluster with common storage. Configuring GFS with rgmanager

  - by Pavel A

  I'm configuring a two node A/A cluster with a common storage attached via iSCSI, which uses GFS2 on top of clustered LVM. So far I have prepared a simple configuration, but am not sure which is the right way to configure gfs resource. Here is the rm section of /etc/cluster/cluster.conf: <rm> <failoverdomains> <failoverdomain name="node1" nofailback="0" ordered="0" restricted="1"> <failoverdomainnode name="rhc-n1"/> </failoverdomain> <failoverdomain name="node2" nofailback="0" ordered="0" restricted="1"> <failoverdomainnode name="rhc-n2"/> </failoverdomain> </failoverdomains> <resources> <script file="/etc/init.d/clvm" name="clvmd"/> <clusterfs name="gfs" fstype="gfs2" mountpoint="/mnt/gfs" device="/dev/vg-cs/lv-gfs"/> </resources> <service name="shared-storage-inst1" autostart="0" domain="node1" exclusive="0" recovery="restart"> <script ref="clvmd"> <clusterfs ref="gfs"/> </script> </service> <service name="shared-storage-inst2" autostart="0" domain="node2" exclusive="0" recovery="restart"> <script ref="clvmd"> <clusterfs ref="gfs"/> </script> </service> </rm> This is what I mean: when using clusterfs resource agent to handle GFS partition, it is not unmounted by default (unless force_unmount option is given). This way when I issue clusvcadm -s shared-storage-inst1 clvm is stopped, but GFS is not unmounted, so a node cannot alter LVM structure on shared storage anymore, but can still access data. And even though a node can do it quite safely (dlm is still running), this seems to be rather inappropriate to me, since clustat reports that the service on a particular node is stopped. Moreover if I later try to stop cman on that node, it will find a dlm locking, produced by GFS, and fail to stop. I could have simply added force_unmount="1", but I would like to know what is the reason behind the default behavior. Why is it not unmounted? Most of the examples out there silently use force_unmount="0", some don't, but none of them give any clue on how the decision was made. Apart from that I have found sample configurations, where people manage GFS partitions with gfs2 init script - https://alteeve.ca/w/2-Node_Red_Hat_KVM_Cluster_Tutorial#Defining_The_Resources or even as simply as just enabling services such as clvm and gfs2 to start automatically at boot (http://pbraun.nethence.com/doc/filesystems/gfs2.html), like: chkconfig gfs2 on If I understand the latest approach correctly, such cluster only controls whether nodes are still alive and can fence errant ones, but such cluster has no control over the status of its resources. I have some experience with Pacemaker and I'm used to that all resources are controlled by a cluster and an action can be taken when not only there are connectivity issues, but any of the resources misbehave. So, which is the right way for me to go: leave GFS partition mounted (any reasons to do so?) set force_unmount="1". Won't this break anything? Why this is not the default? use script resource <script file="/etc/init.d/gfs2" name="gfs"/> to manage GFS partition. start it at boot and don't include in cluster.conf (any reasons to do so?) This may be a sort of question that cannot be answered unambiguously, so it would be also of much value for me if you shared your experience or expressed your thoughts on the issue. How does for example /etc/cluster/cluster.conf look like when configuring gfs with Conga or ccs (they are not available to me since for now I have to use Ubuntu for the cluster)? Thanks you very much!

  Read the article

• Installing .NET Framework 4 Client Profile breaks Windows Update

  - by Richard

  I have a Samsung NC-10 netbook with a fresh install of Windows 7 Home Premium 32-bit (it only had 2GB). If Microsoft .NET Framework 4 Client Profile is installed on it, Windows Update will always return error code 8024402F ("Windows Update encountered an unknown error"). As soon as I uninstall it, Windows Update works just fine again. Out of the four computers in this house, only this netbook has the problem. My question is: How can I get the .NET Framework 4 Client Profile installed on my netbook and continue to have a functioning Windows Update? ----- More information ----- The hard-drive recently died on my netbook so I replaced it with a nice new SSD and did a fresh installation of Windows 7 Home Premium (SP1) - along with all the updates. At some point I found that, when I ran Windows Update, I was greeted with error code 8024402F ("Windows Update encountered an unknown error"). Looking in C:\Windows\WindowsUpdate.log, I saw the following issue: WARNING: ECP: Failed to validate cab file digest downloaded from http://download.windowsupdate.com/msdownload/update/software/dflt/2012/02/4913552_4a5c9563d1f58c77f30d0d5c9999e4b8bff3ab21.cab with error 0x80091007 WARNING: ECP: This roundtrip contained some optimized updates which failed. New Update count = 0, Old Count = 3 FATAL: ProcessCoreMetadata did not return any update to be committed WARNING: Sync of Updates: 0x8024402f WARNING: SyncServerUpdatesInternal failed: 0x8024402f When I downloaded the CAB from the URL listed and opened it, it contained a file called 4913552.txt. A search on Google suggested that it's related to Microsoft .NET Framework 4 Client Profile. Other people had reported problems with it breaking Windows Update, but they were running Windows XP. I tried the steps outlined on the Microsoft site for this error code, but it reported that there was nothing wrong. I also found this superuser question, I tried all the answers listed but none of them made any difference. My router doesn't block ActiveX, changing my internet settings in IE made no difference, assuming it was a corrupted update repository didn't do anything (except wipe my update history), my date and time was correct, switching to Google's DNS didn't work and neither did disabling IPv6. Figuring that this update was corrupted, I repaired it and nothing changed. In desperation I un-installed it and Windows Update started working again! Brilliant! I then downloaded the full version from the Microsoft website, installed it and, thankfully, Windows Update continued to work just fine. A week later I turn on my netbook and Windows Update is broken again with exactly the same error message and log entries as before. Repairing .NET Framework 4 Client Profile did nothing, removing it entirely solved the problem again. Thinking this might be some odd Windows installation issue, I formatted the hard-drive and re-installed Windows. Same problem as before - as soon as .NET Framework 4 Client Profile ended up on the netbook, Windows Update stopped working and reported error 8024402F. As soon as it was un-installed, everything worked just fine again. There are three other machines in this house and all of them have working Windows Update and this Client Profile. Does anyone know why it causes this netbook to break and, more importantly, how I can fix it?

  Read the article

• What is the best server or Ip address to use for prolonged testing?

  - by eldorel

  I usually run uptime/latency tests against (and from) two servers that we own at different sites and until recently I've used the google dns servers as a control group. However, I've realized there is a potential problem with monitoring latency over extended periods of time. Almost all of the major service providers are using ANYCAST. For short tests this doesn't matter, but I need to run a set of tests for at least a week to try and catch an intermittent problem, and a change in the anycast priority while trying to test latency will cause the latency values for that server to change accordingly. Since I'm submitting graphs of this data to the ISP, I need to avoid/account for as many variables as possible. Spikes in the data for only one of the tested servers will only cause headaches. So can anyone recommend servers that: are not using anycast are owned by an entity that has a good uptime reputation (so they can't claim that the problem is server-side) will respond to ICMP requests Have an available service that runs on TCP/UDP (http or dns preferably) Wont consider an automated request every 10 minutes to be abuse Are accessible from anywhere in the world Are not local to the isp ( consider this an investigation of a hostile party ) Thanks in advance. Edit: added #6 and #7 above. More info: I am attempting to demonstrate a network problem for an entire node of our local ISP's network. They are actively blaming the issue on the equipment installed at the customer sites (our backup site is one of these), and refuse to escalate the problem. (even though 2 of these businesses have ISP provided modems, and all of us have completely different routers/services running) I am already quite familiar with the need to test an isp controlled IP, but they are actively dropping all packets targeted at gateway ip addresses and are only passing traffic addressed beyond the gateways. So to demonstrate the issue, I am sending packets to other systems in the same node, systems one hop away from the affected node, and systems completely outside the network. Unfortunately, all of the systems I have currently are either administered directly by myself, or by people who are biased enough to assist me. I need to have several systems included in the trace/log/graphs that are 100% not in the control of either myself or the isp so that the graphs have a stable/unbiased control group. These requirements are straight from legal, I'm just trying to make sure that everything that could be argued to invalidate the data is already covered. In Summary: I need to be able to show tcp/udp/icmp as 3 separate data points, and I need to be able to show the connections inside the local node, from local node to another nearby node, from those 2 nodes to the internet, and through the internet to both verifiable servers and a control group that I have no control over whatsoever. Again, Google/opendns/yahoo/msn/facebook/etc all use anycast, which throws the numbers off every time the anycast caches expire, so I need suggestions of an IP or server that is available for this type of testing. I was hoping someone knew of a system run by someone such as ISC or ICANN, or perhaps even a .gov server (fcc or nsa maybe?) setup for this type of testing. Thanks again.

  Read the article

• what is best config for nginx worker_rlimit_nofile and worker_connections 28672

  - by Binh Nguyen

  i have issue of web-brower response ( especially on ie ) very slow, some time time out, and sometime hang out up to 20 seconds for one file redirect 301 when test with "f12 derverloper tool of ie" .. it report wait/start time very long. but after got connected the elements on web weill be dowload and show out fast ( test at xaluan.com ) It most happen when active user on web more than 2100 ( use google real time live analytic ). server running cenos 5 with ngix, apache, 32core cpu, 96G ram, raid 10 sas hdd.. == flowing is my config == user nobody; # no need for more workers in the proxy mode worker_processes 28; #old 32 #good at 24 error_log /var/log/nginx/error.log; #old add in end: info worker_rlimit_nofile 22528; events { worker_connections 22528; use epoll; # you should use epoll here for Linux kernels 2.6.x } http { server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks off; sendfile on; tcp_nopush on; tcp_nodelay on; server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks off; sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 25; #old 5 gzip on; #old on gzip_vary on; gzip_disable "MSIE [1-6]\."; gzip_proxied any; gzip_http_version 1.1; gzip_min_length 1000; gzip_comp_level 6; gzip_buffers 16 8k; ignore_invalid_headers on; client_header_timeout 1m; #3m client_body_timeout 1m; #3m send_timeout 1m; #3m reset_timedout_connection on; connection_pool_size 256; client_header_buffer_size 256k; large_client_header_buffers 4 256k; client_max_body_size 100M; client_body_buffer_size 256k; request_pool_size 32k; output_buffers 4 32k; postpone_output 1460; proxy_temp_path /tmp/nginx_proxy/; client_body_in_file_only on; log_format bytes_log "$msec $bytes_sent ."; limit_conn_zone $binary_remote_addr zone=limit_per_ip:1m; limit_conn limit_per_ip 20; limit_req_zone $binary_remote_addr zone=allips:5m rate=200r/s; limit_req zone=allips burst=200 nodelay; include "/etc/nginx/vhosts/*"; } =========== I have play around with worker config 1- tried increase as some one suggess: worker_rlimit_nofile = worker_connections = worker_processes * 1024 = 32768 2- tried to set low: worker_processes = 28 and other worker at 22582 and other solution too .. but not work cause some time it make server load hight very quick 3- tried to comment out the # worker_rlimit_nofile . so it will be unlimited. it look like solved a bit about issue response time. but it also make server high load quick in peak time... Please help thanks PS: other apache you may have look for help me out thanks Listen 0.0.0.0:8081 User nobody Group nobody ExtendedStatus On ServerAdmin [email protected] ServerName server.xaluan.com LogLevel warn # These can be set in WHM under 'Apache Global Configuration' Timeout 100 TraceEnable Off ServerSignature Off ServerTokens ProductOnly FileETag None StartServers 15 <IfModule prefork.c> MinSpareServers 20 MaxSpareServers 50 #MaxSpareServers 40 </IfModule> ServerLimit 1572 MaxClients 1572 MaxRequestsPerChild 4000 # MaxRequestsPerChild 3000 KeepAlive On KeepAliveTimeout 3 MaxKeepAliveRequests 300 #MaxKeepAliveRequests 130

  Read the article

• AWS Load balancer connection reset

  - by joshmmo

  I have an ELB set up with two instances. The issue I have with it is that when I do not add www. to it, the ELB just hangs. This is some info I get when I spider with wget: Spider mode enabled. Check if remote file exists. --2013-06-20 13:40:54-- http://learning.example.com/ Resolving learning.example.com... 54.xxx.x.x53, 50.xx.xxx.x71 Connecting to learning.example.com|54.xxx.x.x53|:80... connected. HTTP request sent, awaiting response... No data received. Retrying. when I add www. it works great. I have a GoDaddy SSL cert that I added to the listener section that covers 3 domains, www.learning.example.com, files.learning.example.com and learning.example.com. These are my listener settings: - HTTP 80 HTTPS 443 N/A N/A - SSL 443 SSL 443 Change canvasNew (Change) My EC2 instances are running apache2 on Ubuntu 12.04. I will be happy to post my vhosts file if needed. However, when I ran the server with the domains pointing to just one EC2 instance things worked fine. How can I fix this issue for learning.example.com? Why does www work just fine? A second question would be what is the difference between instance protocol and load balancer protocol? EDIT: Here are the dig results for learning.example.com from yesterday. I changed the DNS entry to point to one instance to make sure it was the elb. When I switch it back I will do it for www.learning.example.com ; <<>> DiG 9.9.1-P2 <<>> learning.example.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 20210 ;; flags: qr rd ra; QUERY: 1, ANSWER: 3, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;learning.example.com. IN A ;; ANSWER SECTION: learning.example.com. 2559 IN CNAME canvas-22222222222.us-west-1.elb.amazonaws.com. canvas-22222222222.us-west-1.elb.amazonaws.com. 60 IN A 54.xxx.x.x53 canvas-22222222222.us-west-1.elb.amazonaws.com. 60 IN A 50.xx.xxx.x71 ;; Query time: 83 msec ;; SERVER: 10.x.xx.20#53(10.x.xx.20) ;; WHEN: Thu Jun 20 13:40:47 2013 ;; MSG SIZE rcvd: 137 EDIT 2: Here is some more info that might be helpful. Port Configuration: 80 (HTTP) forwarding to 443 (HTTPS) Backend Authentication: Disabled Stickiness: Disabled(edit) 443 (SSL, Certificate: canvasNew) forwarding to 443 (SSL) Backend Authentication: Disabled So I switched everything to one EC2 IP address to bypass the elb to make sure things are working. It's running great. www and the non-www url work perfectly fine. Its only when I switch things to the ELB that learning.example.com hangs and www.learning.example.com works. Hopefully you can get some ideas flowing.

  Read the article

• File Server - Storage configuration: RAID vs LVM vs ZFS something else... ?

  - by privatehuff

  We are a small company that does video editing, among other things, and need a place to keep backup copies of large media files and make it easy to share them. I've got a box set up with Ubuntu Server and 4 x 500 GB drives. They're currently set up with Samba as four shared folders that Mac/Windows workstations can see fine, but I want a better solution. There are two major reasons for this: 500 GB is not really big enough (some projects are larger) It is cumbersome to manage the current setup, because individual hard drives have different amounts of free space and duplicated data (for backup). It is confusing now and that will only get worse once there are multiple servers. ("the project is on sever2 in share4" etc) So, I need a way to combine hard drives in such a way as to avoid complete data loss with the failure of a single drive, and so users see only a single share on each server. I've done linux software RAID5 and had a bad experience with it, but would try it again. LVM looks ok but it seems like no one uses it. ZFS seems interesting but it is relatively "new". What is the most efficient and least risky way to to combine the hdd's that is convenient for my users? Edit: The Goal here is basically to create servers that contain an arbitrary number of hard drives but limit complexity from an end-user perspective. (i.e. they see one "folder" per server) Backing up data is not an issue here, but how each solution responds to hardware failure is a serious concern. That is why I lump RAID, LVM, ZFS, and who-knows-what together. My prior experience with RAID5 was also on an Ubuntu Server box and there was a tricky and unlikely set of circumstances that led to complete data loss. I could avoid that again but was left with a feeling that I was adding an unnecessary additional point of failure to the system. I haven't used RAID10 but we are on commodity hardware and the most data drives per box is pretty much fixed at 6. We've got a lot of 500 GB drives and 1.5 TB is pretty small. (Still an option for at least one server, however) I have no experience with LVM and have read conflicting reports on how it handles drive failure. If a (non-striped) LVM setup could handle a single drive failing and only loose whichever files had a portion stored on that drive (and stored most files on a single drive only) we could even live with that. But as long as I have to learn something totally new, I may as well go all the way to ZFS. Unlike LVM, though, I would also have to change my operating system (?) so that increases the distance between where I am and where I want to be. I used a version of solaris at uni and wouldn't mind it terribly, though. On the other end on the IT spectrum, I think I may also explore FreeNAS and/or Openfiler, but that doesn't really solve the how-to-combine-drives issue.

  Read the article

• Problems with XP, Office, and PC in general - any ideas?

  - by molecule

  Hi all This may not make a whole lot of sense so pls bear with me... I am about to perform a routine check on one of my user's PC. Some background - the PC has a Xeon processor and 4Gb of RAM and running XP SP3 He has 2xHDD and pagefile is hosted on the secondary HDD (D:) and min/max values are set to 4096. NO pagefile on C: This user has 6 monitors so he has an NVIDIA Quadro NVS440 hosting 4xmonitors and an NVIDIA Quadro NVS290 hosting 2xmonitors. There is a video card driver from NVIDIA which is compatible with both NVS440 and NVS290 and he is on the latest version of that driver. (Note: Make of video cards are different - one is from leadtek and the other from Nvidia) He is a heavy Bloomberg, Outlook, Word, and Excel user and runs two Citrix applications. Other apps are FoxIt PDF and IE. Problems - Outlook and Excel frequently crashes - I am going to perform an Outlook and Excel repair and also check/remove unnecessary addins - will he lose any customizations if I repaired and chose "Restore my shortcuts while repairing" and do not select "Discard my customized settings and restore default settings". Does repair really repair anything? FYI - It stopped crashing ever since i moved a large spreadsheet he has open to his local HDD instead of over the network. This spreadsheet "refreshes" constantly as it is pulling live data to update cells and I suspect it was auto-saving so frequently that it caused crashes if saving over the network. At times, his right click completely fails to respond. His left click works fine but he can't right click on anything in any Window and even on the desktop. Sometimes, he needs to start to close certain applications such as Adobe and the right click will start functioning again. I removed Adobe and installed FoxIt as I figured it was a resource issue but I do not think so as he does have sufficient resources when the problem is happening. Sometimes he can't bring task manager up until he kills certain apps. Definitely sounds like a resource issue but I am not confident that is the root cause. Also not sure if this is related to one of the apps installed but his Start bar flickers (does not completely disappear) intermittently from time to time. The taskbar icons which are hidden appear and then get hidden again as if it was having "fits". I have performed reg scans, malware scans etc but problems do not go away. I am planning to perform sfc /scannow and office repair but would like to know if anyone has any other suggestions. What about setting a "small" pagefile on C:. I have heard that this is recommended and may be the reason why a minidmp file was not generated when he encountered a blue screen. Also, any feedback on his video cards? Do you think different models would cause problems? The drivers seem to work but he only has 2.5Gb out of 4Gb available RAM as I believe the video card chomped up a portion of this. I have recommended creating a new profile for him but due to the amount of customisations he has and the amount of time and effort it will take to get him up and running again, he prefers to bear with the problem than to go down that path. However, at least once a week, his PC acts up and I can't think of any other tools or techniques to rectify his problems. I guess we are at a stage where we just want to "stabilize" things so he won't encounter issues that frequently. Any feedback is very much appreciated.

  Read the article

• Why does my computer run slowly and freeze sometimes?

  - by Brae

  EDIT I disabled sound in the BIOS, rebooted and it hung. I removed the (previously) faulty HDD, rebooted and it hung. I have managed to get my Realtek audio manager open again after its mysterious disappearance. Subsequently my microphone is now working again, to fix it I had to uninstall audio drivers, disable audio in BIOS, install audio drivers, enable audio in BIOS. Access via network (with faulty HDD in) seems to not be triggering hangs at the moment. I think with the sound problem fixed it might play a little nicer, but I think its still going to hang. If it does, then I'm fairly sure its been narrowed down to the mobo. EDIT Pretty convinced my motherboard is the culprit, because nothing else seems to have any obvious problems (bar the hard drive, which the PC still hangs without it being plugged in) So thank you all for helping, once I get more rep ill up a few of the answers. My PC is doing some weird things... Sometimes when I open up a program, lets say Adobe Photoshop, it will load everything normally, nice and quick no problems and I can use it fine. Other times its a little odd, and it loads the program as if it's only using half of the CPU. It's pretty obvious when it does it, normally the loading screen skims past, but when it does this weird load you see it slowly tick though each thing, and the program itself becomes incredibly slow. Even Google Chrome does it sometimes. Yet when I exit and reopen the program without doing anything else, it typically opens fine without lagging. I think this problem is probably a symptom of something bigger, because of other problems I'm having. Random hangs; no matter what I have open or what I'm doing. My PC will sort of freeze up for a few seconds. If music is playing it will either loop the last second or two, or it will buzz. This only lasts for a few seconds then it returns to normal without having to restart. During this time all programs lock up and freeze, and the mouse and keyboard are useless. I am also having a weird issue with my audio jacks, without touching my PC at all, sometimes I will see a popup saying that I have unplugged something or plugged something in, neither of which has actually happened. Pretty sure this is cause by the motherboard. I recently had a 'Pink Screen of Death' (yes pink) which pointed to my audio drivers. The lockups seem to happen with some consistency when someone is accessing my shared files via my home LAN. Which leads me to believe either one of my hard drives is acting up or more likely the controller. One of my drives had a bit of a crash before, I used Spinrite and managed to recover my stuff and now the drive appears to be working okay. This is possibly adding to the problems. My best guess is something has gone wrong with my motherboard, possibly a power issue or a chip has died, I really don't know. So what I would like to know is: Have I have missed some obvious diagnostic to help figure out what it is, or should I just bite the bullet and assume its my motherboard acting up and buy a new system? dxdiag[64-bit] - http://pastebin.com/G30kb2TL PSOD (minidump) - http://pastebin.com/aZsv0H56 HWiNFO64 (system info / specs) - http://pastebin.com/X6h3K8g6

  Read the article

• SQL Server 2000 and SSL Encryption

  - by Angry_IT_Guru

  We are a datacenter that hsots a SQL Server 2000 environment which provides database services for a product we sell that is loaded as a rich-client applicatin at each of our many clients and their workstations. Currently today, the application uses straight ODBC connections from the client site to our datacenter. We need to begin encrypting the credentials -- since everything is clear-text today and the authentication is weakly encrypted -- and I'm trying to determine the best way to implement SSL on the server with minimizing the impact of the client. A few things, however: 1) We have our own Windows domain and all our servers are joined to our private domain. Our clietns no nothing of our domain. 2) Typically, our clients connect to our datacenter servers either by: a) Using TCP/IP address b) Using a DNS name that we publish via internet, zone transfers from our DNS servers to our customers, or the client can add static HOSTS entries. 3) From what I understand from enabling encryption is that I can go to the Network Utility and select the "encryption" option for the protocol that I wish to encrypt. Such as TCP/IP. 4) When the encryption option is selected, I have a choice of installing a third-party certificate or a self-signed. I have tested the self-signed, but do have potential issues. I'll explain in a bit. If I go with a third-party cert, such as Verisign, or Network solutions... what kind of certificate do I request? These aren't IIS certificates? When I go create a self-signed via Microsoft's certificate server, I have to select "Authentication certificate". What does this translate to in the third-party world? 5) If I create a self-signed certificate, I understand that the "issue to" name has to match the FQDN for the server that is running SQL. In my case, I have to use my private domain name. If I use this, what does this do for my clients when trying to connect to my SQL Server? Surely they cannot resolve my private DNS names on their network.... I've also verified that when the self-signed certificate is installed, it has to be in the local personal store for the user account that is running SQL Server. SQL Server will only start if the FQDN matches the "issue to" of the certificate and SQL is running under the account that has the certificate installed. If I use a self-signed certificate, does this mean I have to have every one of my clients install it to verify? 6) If I used a third-party certificate, which sounds like the best option, do all my clients have to have internet access when accessing my private servers of their private WAN connection to use to verify the certificate? What do I do about the FQDN? It sounds like they have to use my private domain name -- which is not published -- and can no longer use the one that I setup for them to use? 7) I plan on upgrading to SQL 2000 soon. Is setup of SSL any easier/better with SQL 2005 than SQL 2000? Any help or guiadance would be appreciated

  Read the article

• WNDR3700 Router + Cisco SG200-08 + LACP + Dual Uplink

  - by kobaltz

  Background I have a storage server that has several virtual machine images stored on them. I would store them locally, but I have limited space on my desktop (using SSD storage). I would like to increase the bandwidth between the desktop and the storage server by using two NICs on each computer. My original configuration allowed about 55MBps between the desktop and storage server. This storage server also has several TBs of documents, pictures, movies, vms, and ISO/programs. The storage server has 8 1.5TB hard drives in a RAID 10 configuration with a hardware RAID controller. The benchmarks on the RAID 10 are about 300MBps. Configuration In short, I am trying to bridge my switch and router. The switch is a small 8 port Cisco smart switch that supports 802.3ad LACP. I have two computers plugged into the switch, each with 2 Intel Gigabit NICs. The first computer is a Windows 7 machine that has the Intel ANS software installed. I have LACP configured with the computer and now show 3 NICs (2 Physical + 1 TEAM Virtual @ 2Gbps). It looks like this computer is configured correctly. I trunked the two ports that this computer is plugged into with the switch's web interface. The second computer is a homebrew storage box running debian. I also have the bonding enabled on this machine and the switch configured with LACP. Without having the WNDR3700 router in the picture yet, I am able to communicate between the Windows 7 machine and the debian box since they both have static IP addresses. With LACP enabled on both machines I am getting about 106-108MBps speeds. Issue I plug in a network cable from the switch into the router and enable DHCP on the desktop. I saw no need to have a static address on the desktop. My transfer rates are still from 106MBps-108MBps. While this is still a boost, I am trying to figure out how to get about 140-180MBps. I am thinking that I need to increase the bandwidth from the router to the switch. My switch allows 4 groups for port trunking. I plugged in a second network cable from the router to the switch. My question is, what is the proper way to fix this issue. Should I port trunk the two ports that are going from the switch to the router? Keep in mind that the router is a WNDR3700 and is unsure whether or not it supports LACP. I do have OpenWRT installed on the router, but it still wasn't clear in any documentation that I found if it supported 802.3ad LACP standards. I am also wondering if there needs to be anything changed within the Cisco settings. [Edit] - Corrected some numbers, wasn't really paying attention. It looks like the speeds though at least two NICs are bonded with LACP is still reaching the max bandwidth of one port. Is there a way to configure the switch so that I can increase this bandwidth? Also, on the storage server, I had a couple of extra NICs laying around and threw them on there as well. Another EDIT and More Findings I happened to look at the traffic of each individual NIC and think that I see the problem. I tested with a simple transfer for a 4GB file. I noticed that only one of the NICs was taking the load of the traffic. I then copied the file back to the Storage Server and noticed that the other NIC was sending out the traffic. I have 802.3ad LACP enabled on the two NICs and I see that it gets enabled dynamically on the switch's interface. Should I be using Static Link Aggregation?

  Read the article

• Ubuntu Server, 2 Ethernet Devices, Same Gateway - Want to force internet traffic through 1 device (or at least allow it to work!)

  - by Chris Drumgoole

  I have a Ubuntu 10.04 Server with 2 ethernet devices, eth0 and eth1. eth0 has a static IP of 192.168.1.210 eth1 has a static IP if 192.168.1.211 The DHCP server (which also serves as the internet gateway) sits at 192.168.1.1. The issue I have right now is when I have both plugged in, I can connect to both IPs over SSH internally, but I can't connect to the internet from the server. If I unplug one of the devices (e.g. eth1), then it works, no problem. (Also, I get the same result when I run sudo ifconfig eth1 down). Question, how can I configure it so that I can have both devices eth0 and eth1 play nice on the same network, but allow internet access as well? (I am open to either enforcing all inet traffic going through a single device, or through both, I'm flexible). From my google searching, it seems I could have a unique (or not popular) problem, so haven't been able to find a solution. Is this something that people generally don't do? The reason I want to make use of both ethernet devices is because I want to run different local traffic services on on both to split the load, so to speak... Thanks in advance. UPDATE Contents of /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp # The secondary network interface #auto eth1 #iface eth1 inet dhcp (Note: above, I commented out the last 2 lines because I thought that was causing issues... but it didn't solve it) netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 192.168.1.1 255.255.255.0 UG 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 UPDATE 2 I made a change to the /etc/network/interfaces file as suggested by Kevin. Before I display the file contents and the route table, when I am logged into the server (through SSH), I can not ping an external server, so this is the same issue I was experiencing that led to me posting this question. I ran a /etc/init.d/networking restart after making the file changes. Contents of /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp address 192.168.1.210 netmask 255.255.255.0 gateway 192.168.1.1 # The secondary network interface auto eth1 iface eth1 inet dhcp address 192.168.1.211 netmask 255.255.255.0 ifconfig output eth0 Link encap:Ethernet HWaddr 78:2b:cb:4c:02:7f inet addr:192.168.1.210 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::7a2b:cbff:fe4c:27f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6397 errors:0 dropped:0 overruns:0 frame:0 TX packets:683 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:538881 (538.8 KB) TX bytes:85597 (85.5 KB) Interrupt:36 Memory:da000000-da012800 eth1 Link encap:Ethernet HWaddr 78:2b:cb:4c:02:80 inet addr:192.168.1.211 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::7a2b:cbff:fe4c:280/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5799 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:484436 (484.4 KB) TX bytes:1184 (1.1 KB) Interrupt:48 Memory:dc000000-dc012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:635 errors:0 dropped:0 overruns:0 frame:0 TX packets:635 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:38154 (38.1 KB) TX bytes:38154 (38.1 KB) netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0

  Read the article

• Gaming blew fuse and causes funny smell: how to overcome?

  - by George Tomlinson

  I've been gaming for a while now. When playing certain games this PC goes into overdrive. The fan/fans start/s to sound like a jet engine it/they get/s so busy. Also I have smelt burning when this has happened. The fuse blew on the 4 socket adapter I was using recently. On the following thread someone said this could be due to the PSU not being strong enough to handle the load, in what it seems could be a related issue someone had, although the person who posted this question did say that blowing a fan on their PC stopped it crashing in that case: http://www.tomshardware.co.uk/answers/id-2047543/gtx-650-overheating-issue.html. This is exactly what they said: Your GPU isn't overheating. 70+ before it would shutdown and cause a restart. Make sure your PSU is strong enough to handle your new system at load and possibly run Memtest to check your RAM (although not BSOD'ing and just shutting down points to the PSU). This (the PSU part) makes more sense to me than it being to do with dust etc, since it seems a more plausible explanation of why the fuse blew. The PC has no problems except when playing certain games: i.e. TERA Rising and WoW with add-ons (I think WoW is ok as long as I don't have more than 1 add-on (Healers Have To Die)). I'm just wondering if anyone knows or can suggest what I might be able to do to be able to play these games without this problem occurring. The PC's spec is this: Display: NVIDIA GeForce GTX 650 8GB RAM (6 available) Processor: AMD FX (tm) - 8120 Eight-Core Processor - 3.1 GHz, 4 Cores, 8 Logical Processors I have read on another post that forcing vsync in the Nvidia Control Panel helped with what seems could be a similar problem, so I plan to see if that solves it, God permitting. EDIT: I tried the Vsync thing, and it seems the situation may have improved, although this may be due to something else: i.e. maybe the PC was working harder yesterday, due to just having downloaded a few things or lots of things running. I'm still noticing the funny smell when playing TERA. It's not so much burning: it's more like glue. The smell might have had a burning element to it in the past, but I think it's always had a glue element. EDIT 2: the PSU is an 'ATX Switching Power Supply', Model E-500ATX. Other info it gives on the PSU is 230V, Current 10A and Frequency 50-60Hz. It also has some other info which I can supply if necessary. Putting the PC plug in the wall socket instead of the power strip seems like it might have reduced the load on the PC quite a bit: I think it sounds less stressed. it has been off for a while whilst I took the side panel off though, so I'll wait to see what happens before getting too excited. EDIT 3: hmm. So here's the latest: just playing TERA. The fan's running quite fast again. Hard to tell whether switching to the wall socket has made a difference in terms of strain on the PC: I don't know if one would expect it to. Still seems like it might have helped though. Oh and there didn't seem to be much dust in the PC, although I didn't disconnect any components. I'm still getting the glue type smell. ASIDE: reminds me of someone on a PC near me at the library once who was actually sniffing glue right there in front of everyone while on the PC and he started talking about how he was sniffing glue. lol. That's no joke. EDIT 4: So the questions now are: Question 1: Is the smell something I should sort out? (If so, how might I do this?) Question 2: is it necessary to take any steps to prevent blowing another fuse (and if so which step/s?).

  Read the article

• ActiveX component can't create Object Error? Check 64 bit Status

  - by Rick Strahl

  If you're running on IIS 7 and a 64 bit operating system you might run into the following error using ASP classic or ASP.NET with COM interop. In classic ASP applications the error will show up as: ActiveX component can't create object   (Error 429) (actually without error handling the error just shows up as 500 error page) In my case the code that's been giving me problems has been a FoxPro COM object I'd been using to serve banner ads to some of my pages. The code basically looks up banners from a database table and displays them at random. The ASP classic code that uses it looks like this: <% Set banner = Server.CreateObject("wwBanner.aspBanner") banner.BannerFile = "wwsitebanners" Response.Write(banner.GetBanner(-1)) %> Originally this code had no specific error checking as above so the ASP pages just failed with 500 error pages from the Web server. To find out what the problem is this code is more useful at least for debugging: <% ON ERROR RESUME NEXT Set banner = Server.CreateObject("wwBanner.aspBanner") Response.Write(err.Number & " - " & err.Description) banner.BannerFile = "wwsitebanners" Response.Write(banner.GetBanner(-1)) %> which results in: 429 - ActiveX component can't create object which at least gives you a slight clue. In ASP.NET invoking the same COM object with code like this: <% dynamic banner = wwUtils.CreateComInstance("wwBanner.aspBanner") as dynamic; banner.cBANNERFILE = "wwsitebanners"; Response.Write(banner.getBanner(-1)); %> results in: Retrieving the COM class factory for component with CLSID {B5DCBB81-D5F5-11D2-B85E-00600889F23B} failed due to the following error: 80040154 Class not registered (Exception from HRESULT: 0x80040154 (REGDB_E_CLASSNOTREG)). The class is in fact registered though and the COM server loads fine from a command prompt or other COM client. This error can be caused by a COM server that doesn't load. It looks like a COM registration error. There are a number of traditional reasons why this error can crop up of course. The server isn't registered (run regserver32 to register a DLL server or /regserver on an EXE server) Access permissions aren't set on the COM server (Web account has to be able to read the DLL ie. Network service) The COM server fails to load during initialization ie. failing during startup One thing I always do to check for COM errors fire up the server in a COM client outside of IIS and ensure that it works there first - it's almost always easier to debug a server outside of the Web environment. In my case I tried the server in Visual FoxPro on the server with: loBanners = CREATEOBJECT("wwBanner.aspBanner") loBanners.cBannerFile = "wwsitebanners" ? loBanners.GetBanner(-1) and it worked just fine. If you don't have a full dev environment on the server you can also use VBScript do the same thing and run the .vbs file from the command prompt: Set banner = Server.CreateObject("wwBanner.aspBanner") banner.BannerFile = "wwsitebanners" MsgBox(banner.getBanner(-1)) Since this both works it tells me the server is registered and working properly. This leaves startup failures or permissions as the problem. I double checked permissions for the Application Pool and the permissions of the folder where the DLL lives and both are properly set to allow access by the Application Pool impersonated user. Just to be sure I assigned an Admin user to the Application Pool but still no go. So now what? 64 bit Servers Ahoy A couple of weeks back I had set up a few of my Application pools to 64 bit mode. My server is Server 2008 64 bit and by default Application Pools run 64 bit. Originally when I installed the server I set up most of my Application Pools to 32 bit mainly for backwards compatibility. But as more of my code migrates to 64 bit OS's I figured it'd be a good idea to see how well code runs under 64 bit code. The transition has been mostly painless. Until today when I noticed the problem with the code above when scrolling to my IIS logs and noticing a lot of 500 errors on many of my ASP classic pages. The code in question in most of these pages deals with this single simple COM object. It took a while to figure out that the problem is caused by the Application Pool running in 64 bit mode. The issue is that 32 bit COM objects (ie. my old Visual FoxPro COM component) cannot be loaded in a 64 bit Application Pool. The ASP pages using this COM component broke on the day I switched my main Application Pool into 64 bit mode but I didn't find the problem until I searched my logs for errors by pure chance. To fix this is easy enough once you know what the problem is by switching the Application Pool to Enable 32-bit Applications: Once this is done the COM objects started working correctly again. 64 bit ASP and ASP.NET with DCOM Servers This is kind of off topic, but incidentally it's possible to load 32 bit DCOM (out of process) servers from ASP.NET and ASP classic even if those applications run in 64 bit application pools. In fact, in West Wind Web Connection I use this capability to run a 64 bit ASP.NET handler that talks to a 32 bit FoxPro COM server which allows West Wind Web Connection to run in native 64 bit mode without custom configuration (which is actually quite useful). It's probably not a common usage scenario but it's good to know that you can actually access 32 bit COM objects this way from ASP.NET. For West Wind Web Connection this works out well as the DCOM interface only makes one non-chatty call to the backend server that handles all the rest of the request processing. Application Pool Isolation is your Friend For me the recent incident of failure in the classic ASP pages has just been another reminder to be very careful with moving applications to 64 bit operation. There are many little traps when switching to 64 bit that are very difficult to track and test for. I described one issue I had a couple of months ago where one of the default ASP.NET filters was loading the wrong version (32bit instead of 64bit) which was extremely difficult to track down and was caused by a very sneaky configuration switch error (basically 3 different entries for the same ISAPI filter all with different bitness settings). It took me almost a full day to track this down). Recently I've been taken to isolate individual applications into separate Application Pools rather than my past practice of combining many apps into shared AppPools. This is a good practice assuming you have enough memory to make this work. Application Pool isolate provides more modularity and allows me to selectively move applications to 64 bit. The error above came about precisely because I moved one of my most populous app pools to 64 bit and forgot about the minimal COM object use in some of my old pages. It's easy to forget. To 64bit or Not Is it worth it to move to 64 bit? Currently I'd say -not really. In my - admittedly limited - testing I don't see any significant performance increases. In fact 64 bit apps just seem to consume considerably more memory (30-50% more in my pools on average) and performance is minimally improved (less than 5% at the very best) in the load testing I've performed on a couple of sites in both modes. The only real incentive for 64 bit would be applications that require huge data spaces that exceed the 32 bit 4 gigabyte memory limit. However I have a hard time imagining an application that needs 4 gigs of memory in a single Application Pool :-). Curious to hear other opinions on benefits of 64 bit operation. © Rick Strahl, West Wind Technologies, 2005-2011Posted in COM   ASP.NET  FoxPro  

  Read the article

• Unity completely broken after upgrade to 12.10?

  - by NlightNFotis

  I am facing a very frustrating issue with my computer right now. I successfully upgraded to Ubuntu 12.10 this afternoon, but after the upgrade, the graphical user interface seems completely broken. To be more specific, I can not get the Unity bar to appear on the right. I have tried many things, including (but not limited to) purging and then reinstalling the fglrx drivers, apt-get install --reinstall ubuntu-desktop, apt-get install --reinstall unity, tried to remove the Xorg and Compiz configurations, checked to see if the Ubuntu Unity wall was enabled (it was) in ccsm, all to no avail. Could someone help me troubleshoot and essentially fix this issue? NOTE: This is the output when I try to enable unity via a terminal: compiz (core) - Info: Loading plugin: core compiz (core) - Info: Starting plugin: core unity-panel-service: no process found compiz (core) - Info: Loading plugin: reset compiz (core) - Error: Failed to load plugin: reset compiz (core) - Info: Loading plugin: ccp compiz (core) - Info: Starting plugin: ccp compizconfig - Info: Backend : gsettings compizconfig - Info: Integration : true compizconfig - Info: Profile : unity compiz (core) - Info: Loading plugin: composite compiz (core) - Info: Starting plugin: composite compiz (core) - Info: Loading plugin: opengl X Error of failed request: BadRequest (invalid request code or no such operation) Major opcode of failed request: 153 (GLX) Minor opcode of failed request: 19 (X_GLXQueryServerString) Serial number of failed request: 22 Current serial number in output stream: 22 compiz (core) - Info: Unity is not supported by your hardware. Enabling software rendering instead (slow). compiz (core) - Info: Starting plugin: opengl Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 compiz (core) - Error: Plugin initScreen failed: opengl compiz (core) - Error: Failed to start plugin: opengl compiz (core) - Info: Unloading plugin: opengl compiz (core) - Info: Loading plugin: decor compiz (core) - Info: Starting plugin: decor compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available compiz (decor) - Warn: requested a pixmap type decoration when compositing isn't available Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 compiz (core) - Info: Loading plugin: imgpng compiz (core) - Info: Starting plugin: imgpng compiz (core) - Info: Loading plugin: vpswitch compiz (core) - Info: Starting plugin: vpswitch compiz (core) - Info: Loading plugin: resize compiz (core) - Info: Starting plugin: resize Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 compiz (core) - Info: Loading plugin: compiztoolbox compiz (core) - Info: Starting plugin: compiztoolbox compiz (core) - Error: Plugin 'opengl' not loaded. compiz (core) - Info: Loading plugin: move compiz (core) - Info: Starting plugin: move compiz (core) - Info: Loading plugin: gnomecompat compiz (core) - Info: Starting plugin: gnomecompat compiz (core) - Info: Loading plugin: mousepoll compiz (core) - Info: Starting plugin: mousepoll compiz (core) - Info: Loading plugin: wall compiz (core) - Info: Starting plugin: wall compiz (core) - Error: Plugin 'opengl' not loaded. compiz (core) - Error: Plugin init failed: wall compiz (core) - Error: Failed to start plugin: wall compiz (core) - Info: Unloading plugin: wall compiz (core) - Info: Loading plugin: regex compiz (core) - Info: Starting plugin: regex compiz (core) - Info: Loading plugin: snap compiz (core) - Info: Starting plugin: snap compiz (core) - Info: Loading plugin: unitymtgrabhandles compiz (core) - Info: Starting plugin: unitymtgrabhandles compiz (core) - Error: Plugin 'opengl' not loaded. compiz (core) - Error: Plugin init failed: unitymtgrabhandles compiz (core) - Error: Failed to start plugin: unitymtgrabhandles compiz (core) - Info: Unloading plugin: unitymtgrabhandles compiz (core) - Info: Loading plugin: place compiz (core) - Info: Starting plugin: place compiz (core) - Info: Loading plugin: grid compiz (core) - Info: Starting plugin: grid Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 compiz (core) - Info: Loading plugin: animation compiz (core) - Info: Starting plugin: animation compiz (core) - Error: Plugin 'opengl' not loaded. compiz (core) - Error: Plugin init failed: animation compiz (core) - Error: Failed to start plugin: animation compiz (core) - Info: Unloading plugin: animation compiz (core) - Info: Loading plugin: fade compiz (core) - Info: Starting plugin: fade compiz (core) - Error: Plugin 'opengl' not loaded. compiz (core) - Error: Plugin init failed: fade compiz (core) - Error: Failed to start plugin: fade compiz (core) - Info: Unloading plugin: fade compiz (core) - Info: Loading plugin: session compiz (core) - Info: Starting plugin: session compiz (core) - Info: Loading plugin: expo compiz (core) - Info: Starting plugin: expo compiz (core) - Error: Plugin 'opengl' not loaded. compiz (core) - Error: Plugin init failed: expo compiz (core) - Error: Failed to start plugin: expo compiz (core) - Info: Unloading plugin: expo compiz (core) - Info: Loading plugin: ezoom compiz (core) - Info: Starting plugin: ezoom compiz (core) - Error: Plugin 'opengl' not loaded. compiz (core) - Error: Plugin init failed: ezoom compiz (core) - Error: Failed to start plugin: ezoom compiz (core) - Info: Unloading plugin: ezoom compiz (core) - Info: Loading plugin: workarounds compiz (core) - Info: Starting plugin: workarounds compiz (core) - Error: Plugin 'opengl' not loaded. Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 compiz (core) - Info: Loading plugin: scale compiz (core) - Info: Starting plugin: scale compiz (core) - Error: Plugin 'opengl' not loaded. compiz (core) - Error: Plugin init failed: scale compiz (core) - Error: Failed to start plugin: scale compiz (core) - Info: Unloading plugin: scale Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Compiz (opengl) - Fatal: glXQueryExtensionsString is NULL for screen 0 Segmentation fault (core dumped)

  Read the article

• CodePlex Daily Summary for Monday, February 22, 2010

  CodePlex Daily Summary for Monday, February 22, 2010New ProjectsAVDB: System to keep track of orders and the inventory of televisions, DVDs, VCRs etcBooky: Booky is an online Bookmark Management Tool. Gear Up for Lord of the Rings Online (lotro): Windows utility for checking what your LOTRO character currently has equipped and figuring out gear you should get to improve your stats.GotSharp Extensions: GotSharp Extensions is a set of helpful classes and extension methods that can make your coding experience easier and cleaner. Halfwit: A minimalist WPF Twitter client.HOA Starter Kit: A community subdivision website starter kit. First draft.Lua For Irony: Project to define the Lua language using the Irony (http://irony.codeplex.com/) development kit. This work is based heavily on the work done for V...MimeCloud: Scalable .NET Digital Asset & Media Management: MimeCloud is a scalable digital asset library & media management toolset. Founded by Alex Norcliffe and Peter Miller Written by people who have b...Parallel Mandelbrot Set solver: Solving the Mandelbrot set using the Parallel class in .NET 4.0. Showing the resulting image in a WPF application. The solution file requires VS 2010.Pomogad - Pomodoro Windows Gadget: Você usa Pomodoro Technique? Não sabe o que é? Veja aqui http://www.pomodorotechnique.com Agora que você já sabe, que tal usar essa técnica? E p...PostCrap - flyweight .NET AOP post compiler: PostCrap is a flyweight attribute based aspect injection .NET post compiler It is written in C# and uses Mono.Cecil to modify assemblies and injec...Software + Service Reference Demo Kit: MS China Developer and Platform Evangelism team created an End-2-End demo for Software + Service. Yet Another SharePoint Tool: YEAST provides you with a simple to integrate approach to generating SharePoint solution packages as part of a Visual Studio project. Zen Coding Visual Studio Plugin: Zen Coding for Visual Studio is plugin for HTML and CSS hi-speed codingNew Releases.Net MSBuild Google Closure Compiler Task: .Net MSBuild Google Closure Compiler Task 1.1: - Corrected issue with regular expression source file and renamingdotNails: dotNails_0.5.9: NOTE - the latest source code has been moved to google code to take advantage of Mercurial source control - http://code.google.com/p/dotnails/sourc...EasyWFUnit: EasyWFUnit-2.2: Release 2.2 of EasyWFUnit, an extension library to support unit testing of Windows Workflow, includes a revised WinForm GUI Test Builder that utili...Fluent Ribbon Control Suite: Fluent Ribbon Control Suite BETA2 (for .NET 4.0RC): Includes Fluent.dll (with .pdb and .xml) and test application compiled with .NET 4.0 RC.FolderSize: FolderSize.Win32.1.0.3.0: FolderSize.Win32.1.0.3.0 A simple utility intended to be used to scan harddrives for the folders that take most place and display this to the user...Fusion Charts Free for SharePoint: 1.3: Fix release for issue #11833 : Feature Must Be Activated on Root of Web Application.GotSharp Extensions: 1.0: First release, containing only a few extension methods for the System.String and System.IO.Stream classes, and a Range utility class.Jeremy's Experimental Repository: FluentValidation with IoC Sample: Sample code for the blog post Using FluentValidation with an IoC containerMiniTwitter: 1.08: MiniTwitter 1.08 更新内容 修正 自動更新が CodePlex の変更で動いていなかった問題を修正 自動更新に失敗すると落ちるバグを修正 通知領域アイコン右クリックで表示されるメニューが消えないバグを修正 変更 ハッシュタグの抽出条件を変更 API のエンドポイ...MSTS Editors & Tools: Simis Editor v0.3: Simis Editor v0.3 Enabled Edit > Undo and Edit > Redo. Undoing/redoing back to last saved state is identified as saved (no prompt on exit, etc.)....Parallel Mandelbrot Set solver: Alpha 1: First releaseParallelTasks: ParallelTasks 2.0 beta1: ParallelTasks 2.0 is a total re-write of the original version. Featuring improved performance and stability and a more consistent API.Personal Expense Tracker: Personal Expense Tracker v0.1 beta: This is the first beta release. Please provide me with your feedback.PostCrap - flyweight .NET AOP post compiler: PostCrap 1.0 AOP source and binaries: PostCrap 1.0 source and binaries (the unit test project contains sample interceptor attributes for exception handling & logging)Protoforma | Tactica Adversa: Skilful 0.1.3.276: AlphaRawr: Rawr 2.3.10: - More improvements to the default filters - Further improvement on avoiding useless gem swaps from the Optimizer. - Normal/Heroic ICC items shou...Reusable Library: v1.0.2: A collection of reusable abstractions for enterprise application developer.Sem.Sync: 2010-02-21 - Synchronization Manager - Beta: This release is not tested very well, so you should use this version only to evaluate new features. - Changed way of handling source-ids in order ...Survey - web survey & form engine: Survey 1.1.0: Release Survey v. 1.1.0.0 Major changes: - layout & graphics completely overhauled - several technical changes & repairs (e.g. matrix question iss...Yet Another SharePoint Tool: Version 1: Version 1Zeta Resource Editor: Release 2010-02-21: New source code release.Most Popular ProjectsWBFS ManagerRawrAJAX Control ToolkitMicrosoft SQL Server Product Samples: DatabaseSilverlight ToolkitWindows Presentation Foundation (WPF)Image Resizer Powertoy Clone for WindowsASP.NETDotNetNuke® Community EditionMicrosoft SQL Server Community & SamplesMost Active ProjectsDinnerNow.netRawrBlogEngine.NETNB_Store - Free DotNetNuke Ecommerce Catalog ModuleSharpyjQuery Library for SharePoint Web ServicesSharePoint ContribInfoServicepatterns & practices – Enterprise LibraryPHPExcel

  Read the article

• Ajax Control Toolkit and Superexpert

  - by Stephen Walther

  Microsoft has asked my company, Superexpert Consulting, to take ownership of the development and maintenance of the Ajax Control Toolkit moving forward. In this blog entry, I discuss our strategy for improving the Ajax Control Toolkit. Why the Ajax Control Toolkit? The Ajax Control Toolkit is one of the most popular projects on CodePlex. In fact, some have argued that it is among the most successful open-source projects of all time. It consistently receives over 3,500 downloads a day (not weekends -- workdays). A mind-boggling number of developers use the Ajax Control Toolkit in their ASP.NET Web Forms applications. Why does the Ajax Control Toolkit continue to be such a popular project? The Ajax Control Toolkit fills a strong need in the ASP.NET Web Forms world. The Toolkit enables Web Forms developers to build richly interactive JavaScript applications without writing any JavaScript. For example, by taking advantage of the Ajax Control Toolkit, a Web Forms developer can add modal dialogs, popup calendars, and client tabs to a web application simply by dragging web controls onto a page. The Ajax Control Toolkit is not for everyone. If you are comfortable writing JavaScript then I recommend that you investigate using jQuery plugins instead of the Ajax Control Toolkit. However, if you are a Web Forms developer and you don’t want to get your hands dirty writing JavaScript, then the Ajax Control Toolkit is a great solution. The Ajax Control Toolkit is Vast The Ajax Control Toolkit consists of 40 controls. That’s a lot of controls (For the sake of comparison, jQuery UI consists of only 8 controls – those slackers J). Furthermore, developers expect the Ajax Control Toolkit to work on browsers both old and new. For example, people expect the Ajax Control Toolkit to work with Internet Explorer 6 and Internet Explorer 9 and every version of Internet Explorer in between. People also expect the Ajax Control Toolkit to work on the latest versions of Mozilla Firefox, Apple Safari, and Google Chrome. And, people expect the Ajax Control Toolkit to work with different operating systems. Yikes, that is a lot of combinations. The biggest challenge which my company faces in supporting the Ajax Control Toolkit is ensuring that the Ajax Control Toolkit works across all of these different browsers and operating systems. Testing, Testing, Testing Because we wanted to ensure that we could easily test the Ajax Control Toolkit with different browsers, the very first thing that we did was to set up a dedicated testing server. The dedicated server -- named Schizo -- hosts 4 virtual machines so that we can run Internet Explorer 6, Internet Explorer 7, Internet Explorer 8, and Internet Explorer 9 at the same time (We also use the virtual machines to host the latest versions of Firefox, Chrome, Opera, and Safari). The five developers on our team (plus me) can each publish to a separate FTP website on the testing server. That way, we can quickly test how changes to the Ajax Control Toolkit affect different browsers. QUnit Tests for the Ajax Control Toolkit Introducing regressions – introducing new bugs when trying to fix existing bugs – is the concern which prevents me from sleeping well at night. There are so many people using the Ajax Control Toolkit in so many unique scenarios, that it is difficult to make improvements to the Ajax Control Toolkit without introducing regressions. In order to avoid regressions, we decided early on that it was extremely important to build good test coverage for the 40 controls in the Ajax Control Toolkit. We’ve been focusing a lot of energy on building automated JavaScript unit tests which we can use to help us discover regressions. We decided to write the unit tests with the QUnit test framework. We picked QUnit because it is quickly becoming the standard unit testing framework in the JavaScript world. For example, it is the unit testing framework used by the jQuery team, the jQuery UI team, and many jQuery UI plugin developers. We had to make several enhancements to the QUnit framework in order to test the Ajax Control Toolkit. For example, QUnit does not support tests which include postbacks. We modified the QUnit framework so that it works with IFrames so we could perform postbacks in our automated tests. At this point, we have written hundreds of QUnit tests. For example, we have written 135 QUnit tests for the Accordion control. The QUnit tests are included with the Ajax Control Toolkit source code in a project named AjaxControlToolkit.Tests. You can run all of the QUnit tests contained in the project by opening the Default.aspx page. Automating the QUnit Tests across Multiple Browsers Automated tests are useless if no one ever runs them. In order for the QUnit tests to be useful, we needed an easy way to run the tests automatically against a matrix of browsers. We wanted to run the unit tests against Internet Explorer 6, Internet Explorer 7, Internet Explorer 8, Internet Explorer 9, Firefox, Chrome, and Safari automatically. Expecting a developer to run QUnit tests against every browser after every check-in is just too much to expect. It takes 20 seconds to run the Accordion QUnit tests. We are testing against 8 browsers. That would require the developer to open 8 browsers and wait for the results after each change in code. Too much work. Therefore, we built a JavaScript Test Server. Our JavaScript Test Server project was inspired by John Resig’s TestSwarm project. The JavaScript Test Server runs our QUnit tests in a swarm of browsers (running on different operating systems) automatically. Here’s how the JavaScript Test Server works: 1. We created an ASP.NET page named RunTest.aspx that constantly polls the JavaScript Test Server for a new set of QUnit tests to run. After the RunTest.aspx page runs the QUnit tests, the RunTest.aspx records the test results back to the JavaScript Test Server. 2. We opened the RunTest.aspx page on instances of Internet Explorer 6, Internet Explorer 7, Internet Explorer 8, Internet Explorer 9, FireFox, Chrome, Opera, Google, and Safari. Now that we have the JavaScript Test Server setup, we can run all of our QUnit tests against all of the browsers which we need to support with a single click of a button. A New Release of the Ajax Control Toolkit Each Month The Ajax Control Toolkit Issue Tracker contains over one thousand five hundred open issues and feature requests. So we have plenty of work on our plates J At CodePlex, anyone can vote for an issue to be fixed. Originally, we planned to fix issues in order of their votes. However, we quickly discovered that this approach was inefficient. Constantly switching back and forth between different controls was too time-consuming. It takes time to re-familiarize yourself with a control. Instead, we decided to focus on two or three controls each month and really focus on fixing the issues with those controls. This way, we can fix sets of related issues and avoid the randomization caused by context switching. Our team works in monthly sprints. We plan to do another release of the Ajax Control Toolkit each and every month. So far, we have competed one release of the Ajax Control Toolkit which was released on April 1, 2011. We plan to release a new version in early May. Conclusion Fortunately, I work with a team of smart developers. We currently have 5 developers working on the Ajax Control Toolkit (not full-time, they are also building two very cool ASP.NET MVC applications). All the developers who work on our team are required to have strong JavaScript, jQuery, and ASP.NET MVC skills. In the interest of being as transparent as possible about our work on the Ajax Control Toolkit, I plan to blog frequently about our team’s ongoing work. In my next blog entry, I plan to write about the two Ajax Control Toolkit controls which are the focus of our work for next release.

  Read the article

• HttpContext.Items and Server.Transfer/Execute

  - by Rick Strahl

  A few days ago my buddy Ben Jones pointed out that he ran into a bug in the ScriptContainer control in the West Wind Web and Ajax Toolkit. The problem was basically that when a Server.Transfer call was applied the script container (and also various ClientScriptProxy script embedding routines) would potentially fail to load up the specified scripts. It turns out the problem is due to the fact that the various components in the toolkit use request specific singletons via a Current property. I use a static Current property tied to a Context.Items[] entry to handle this type of operation which looks something like this: /// <summary> /// Current instance of this class which should always be used to /// access this object. There are no public constructors to /// ensure the reference is used as a Singleton to further /// ensure that all scripts are written to the same clientscript /// manager. /// </summary> public static ClientScriptProxy Current { get { if (HttpContext.Current == null) return new ClientScriptProxy(); ClientScriptProxy proxy = null; if (HttpContext.Current.Items.Contains(STR_CONTEXTID)) proxy = HttpContext.Current.Items[STR_CONTEXTID] as ClientScriptProxy; else { proxy = new ClientScriptProxy(); HttpContext.Current.Items[STR_CONTEXTID] = proxy; } return proxy; } } The proxy is attached to a Context.Items[] item which makes the instance Request specific. This works perfectly fine in most situations EXCEPT when you’re dealing with Server.Transfer/Execute requests. Server.Transfer doesn’t cause Context.Items to be cleared so both the current transferred request and the original request’s Context.Items collection apply. For the ClientScriptProxy this causes a problem because script references are tracked on a per request basis in Context.Items to check for script duplication. Once a script is rendered an ID is written into the Context collection and so considered ‘rendered’: // No dupes - ref script include only once if (HttpContext.Current.Items.Contains( STR_SCRIPTITEM_IDENTITIFIER + fileId ) ) return; HttpContext.Current.Items.Add(STR_SCRIPTITEM_IDENTITIFIER + fileId, string.Empty); where the fileId is the script name or unique identifier. The problem is on the Transferred page the item will already exist in Context and so fail to render because it thinks the script has already rendered based on the Context item. Bummer. The workaround for this is simple once you know what’s going on, but in this case it was a bitch to track down because the context items are used in many places throughout this class. The trick is to determine when a request is transferred and then removing the specific keys. The first issue is to determine if a script is in a Trransfer or Execute call: if (HttpContext.Current.CurrentHandler != HttpContext.Current.Handler) Context.Handler is the original handler and CurrentHandler is the actual currently executing handler that is running when a Transfer/Execute is active. You can also use Context.PreviousHandler to get the last handler and chain through the whole list of handlers applied if Transfer calls are nested (dog help us all for the person debugging that). For the ClientScriptProxy the full logic to check for a transfer and remove the code looks like this: /// <summary> /// Clears all the request specific context items which are script references /// and the script placement index. /// </summary> public void ClearContextItemsOnTransfer() { if (HttpContext.Current != null) { // Check for Server.Transfer/Execute calls - we need to clear out Context.Items if (HttpContext.Current.CurrentHandler != HttpContext.Current.Handler) { List<string> Keys = HttpContext.Current.Items.Keys.Cast<string>().Where(s => s.StartsWith(STR_SCRIPTITEM_IDENTITIFIER) || s == STR_ScriptResourceIndex).ToList(); foreach (string key in Keys) { HttpContext.Current.Items.Remove(key); } } } } along with a small update to the Current property getter that sets a global flag to indicate whether the request was transferred: if (!proxy.IsTransferred && HttpContext.Current.Handler != HttpContext.Current.CurrentHandler) { proxy.ClearContextItemsOnTransfer(); proxy.IsTransferred = true; } return proxy; I know this is pretty ugly, but it works and it’s actually minimal fuss without affecting the behavior of the rest of the class. Ben had a different solution that involved explicitly clearing out the Context items and replacing the collection with a manually maintained list of items which also works, but required changes through the code to make this work. In hindsight, it would have been better to use a single object that encapsulates all the ‘persisted’ values and store that object in Context instead of all these individual small morsels. Hindsight is always 20/20 though :-}. If possible use Page.Items ClientScriptProxy is a generic component that can be used from anywhere in ASP.NET, so there are various methods that are not Page specific on this component which is why I used Context.Items, rather than the Page.Items collection.Page.Items would be a better choice since it will sidestep the above Server.Transfer nightmares as the Page is reloaded completely and so any new Page gets a new Items collection. No fuss there. So for the ScriptContainer control, which has to live on the page the behavior is a little different. It is attached to Page.Items (since it’s a control): /// <summary> /// Returns a current instance of this control if an instance /// is already loaded on the page. Otherwise a new instance is /// created, added to the Form and returned. /// /// It's important this function is not called too early in the /// page cycle - it should not be called before Page.OnInit(). /// /// This property is the preferred way to get a reference to a /// ScriptContainer control that is either already on a page /// or needs to be created. Controls in particular should always /// use this property. /// </summary> public static ScriptContainer Current { get { // We need a context for this to work! if (HttpContext.Current == null) return null; Page page = HttpContext.Current.CurrentHandler as Page; if (page == null) throw new InvalidOperationException(Resources.ERROR_ScriptContainer_OnlyWorks_With_PageBasedHandlers); ScriptContainer ctl = null; // Retrieve the current instance ctl = page.Items[STR_CONTEXTID] as ScriptContainer; if (ctl != null) return ctl; ctl = new ScriptContainer(); page.Form.Controls.Add(ctl); return ctl; } } The biggest issue with this approach is that you have to explicitly retrieve the page in the static Current property. Notice again the use of CurrentHandler (rather than Handler which was my original implementation) to ensure you get the latest page including the one that Server.Transfer fired. Server.Transfer and Server.Execute are Evil All that said – this fix is probably for the 2 people who are crazy enough to rely on Server.Transfer/Execute. :-} There are so many weird behavior problems with these commands that I avoid them at all costs. I don’t think I have a single application that uses either of these commands… Related Resources Full source of ClientScriptProxy.cs (repository) Part of the West Wind Web Toolkit Static Singletons for ASP.NET Controls Post © Rick Strahl, West Wind Technologies, 2005-2010Posted in ASP.NET  

  Read the article

• Security Trimmed Cross Site Collection Navigation

  - by Sahil Malik

  Ad:: SharePoint 2007 Training in .NET 3.5 technologies (more information). This article will serve as documentation of a fully functional codeplex project that I just created. This project will give you a WebPart that will give you security trimmed navigation across site collections. The first question is, why create such a project? In every single SharePoint project you will do, one question you will always be faced with is, what should the boundaries of sites be, and what should the boundaries of site collections be? There is no good or bad answer to this, because it really really depends on your needs. There are some factors in play here. Site Collections will allow you to scale, as a Site collection is the smallest entity you can put inside a content database Site collections will allow you to offer different levels of SLAs, because you put a site collection on a separate content database, and put that database on a separate server. Site collections are a security boundary – and they can be moved around at will without affecting other site collections. Site collections are also a branding boundary. They are also a feature deployment boundary, so you can have two site collections on the same web application with completely different nature of services. But site collections break navigation, i.e. a site collection at “/”, and a site collection at “/sites/mySiteCollection”, are completely independent of each other. If you have access to both, the navigation of / won’t show you a link to /sites/mySiteCollection. Some people refer to this as a huge issue in SharePoint. Luckily, some workarounds exist. A long time ago, I had blogged about “Implementing Consistent Navigation across Site Collections”. That approach was a no-code solution, it worked – it gave you a consistent navigation across site collections. But, it didn’t work in a security trimmed fashion! i.e., if I don’t have access to Site Collection ‘X’, it would still show me a link to ‘X’. Well this project gets around that issue. Simply deploy this project, and it’ll give you a WebPart. You can use that WebPart as either a webpart or as a server control dropped via SharePoint designer, and it will give you Security Trimmed Cross Site Collection Navigation. The code has been written for SP2010, but it will work in SP2007 with the help of http://spwcfsupport.codeplex.com . What do I need to do to make it work? I’m glad you asked! Simple! Deploy the .wsp (which you can download here). This will give you a site collection feature called “Winsmarts Cross Site Collection Navigation” as shown below. Go ahead and activate it, and this will give you a WebPart called “Winsmarts Navigation Web Part” as shown below: Just drop this WebPart on your page, and it will show you all site collections that the currently logged in user has access to. Really it’s that easy! This is shown as below - In the above example, I have two site collections that I created at /sites/SiteCollection1 and /sites/SiteCollection2. The navigation shows the titles. You see some extraneous crap as well, you might want to clean that – I’ll talk about that in a minute. What? You’re running into problems? If the problem you’re running into is that you are prompted to login three times, and then it shows a blank webpart that says “Loading your applications ..” and then craps out!, then most probably you’re using a different authentication scheme. Behind the scenes I use a custom WCF service to perform this job. OOTB, I’ve set it to work with NTLM, but if you need to make it work alternate authentications such as forms based auth, or client side certs, you will need to edit the %14%\ISAPI\Winsmarts.CrossSCNav\web.config file, specifically, this section - 1: <bindings> 2: <webHttpBinding> 3: <binding name="customWebHttpBinding"> 4: <security mode="TransportCredentialOnly"> 5: <transport clientCredentialType="Ntlm"/> 6: </security> 7: </binding> 8: </webHttpBinding> 9: </bindings> For Kerberos, change the “clientCredentialType” to “Windows” For Forms auth, remove that transport line For client certs – well that’s a bit more involved, but it’s just web.config changes – hit a good book on WCF or hire me for a billion trillion $. But fair warning, I might be too busy to help immediately. If you’re running into a different problem, please leave a comment below, but the code is pretty rock solid, so .. hmm .. check what you’re doing! BTW, I don’t  make any guarantee/warranty on this – if this code makes you sterile, unpopular, bad hairstyle, anything else, that is your problem! But, there are some known issues - I wrote this as a concept – you can easily extend it to be more flexible. Example, hierarchical nav, or, horizontal nav, jazzy effects with jquery or silverlight– all those are possible very very easily. This webpart is not smart enough to co-exist with another instance of itself on the same page. I can easily extend it to do so, which I will do in my spare(!?) time! Okay good! But that’s not all! As you can see, just dropping the WebPart may show you many extraneous site collections, or maybe you want to restrict which site collections are shown, or exclude a certain site collection to be shown from the navigation. To support that, I created a property on the WebPart called “UrlMatchPattern”, which is a regex expression you specify to trim the results :). So, just edit the WebPart, and specify a string property of “http://sp2010/sites/” as shown below. Note that you can put in whatever regex expression you want! So go crazy, I don’t care! And this gives you a cleaner look.   w00t! Enjoy! Comment on the article ....

  Read the article

< Previous Page | 392 393 394 395 396 397 398 399 400 401 402 403  | Next Page >