Search Results

Search found 16598 results on 664 pages for 'device center'.

Page 399/664 | < Previous Page | 395 396 397 398 399 400 401 402 403 404 405 406  | Next Page >

• Forward a port with modem (with built-in but disabled router) + a separate router

  - by Youn

  I have a Motorola SBG6580 that is a modem and a wireless router in one. However, the wireless router part was bad so I disabled it and got a separate wireless router. I can go into the configuration pages of both the modem and the router now, and I'm confused as to which device needs to be configured for port-forwarding. I have a raspberry pi that I want to set up as a webserver. Do I configure the router, the modem, or both? Right now, the SBG6580's 1st LAN is connected to the wireless router's WAN, and the internet is working well. Note that the SBG6580 only has 4 ports, and I'm assuming they're LAN,as they are not labeled.

  Read the article

• SOHO Netflix and network security

  - by TW

  I want to use WIFI for HiDef video, but I don't trust it for my office PC's. I've heard of VLANs but I have no idea how to set it up or what (SOHO) hardware to buy. Other than getting 2 different DSL lines, how can I be absolutely sure that the PC side doesn't get hacked? What if I want to use MS Home server as a backup device for both sides? Can I make it "read only" for the PC side, and physically change the cable if I need to restore? TW

  Read the article

• Installing SDM on a Cisco 2821 ISR

  - by Sam Sanders

  I trying to change the configuration of our router, it's a Cisco 2821 Integrated Services Router. I don't know much about Cisco products. While looking at the PDF manual for the router I notices it talked about SDM Security Device Manager. But when I point my web browser at the IP address of the router, it give me a very simple web interface. It's sort of like a string builder for CLI commands. I'm guessing SDM was not installed on it. So my question how would I go about do that? I found this link (below), but I'm a bit new to networking. So any advice would be welcome. http://www.cisco.com/en/US/docs/routers/access/cisco_router_and_security_device_manager/software/quick/guide/SDMq7.html

  Read the article

• Can't connect to exchange thru my smart phone

  - by Hoorayo

  We just moved Exchange server from our company to Local data center. Everything is working except mobile access. There is no problem with receiving and sending email from outlook of my laptop, but I can’t connect to exchange server from my smart phone to receive email. While I am setting up exchange account for my phone(Google) , it recognizes when I put wrong password. But it says “Unable to open connection to server” with right password and ID. Is there any option for IP address for this service when I move my server to different location? Please, help me out for any clue.

  Read the article

• Updating drivers on a Lenovo T410

  - by dcd018

  I have a few question regarding updating the drivers on my Lenovo T410. I have Windows 7 Ultimate 64 bit installed with a 32 bit(X86) sub directory. I'm not that familiar with updating drivers on 64bit Windows so I'm wondering if I should install both 32/64 bit driver versions instead of just 64 bit. Another question I have is Lenovo specific. On the support page for my device, there is a list of Windows updates available dating back to 2009, however I do have ThinkVantage update manager installed and it checks for Windows updates weekly. Should I install all of the Windows specific updates, or can I rely on update manager? My last question is if I should install the drivers for the T410 in any specific order? Any help is much appreciated as I haven't been able to find answers to these specific questions here, or by googling. Thanks in advance

  Read the article

• Mac Mini 1.66 no sound on Windows 7

  - by Steph

  I've tried everything I could to get the sound working. I've tried to install the drivers from the Snow Leopard disk, then I went and got the latest RealTek drivers from the RealTek website. Then I read that old Mac mini's could have an integrated Cirrus chip, and I tried to grab the latest driver from the website, and it appeared to install, but nothing. There's also nothing listed under Sound and ... in the Device Manager. I've tried to manually include a legacy driver, which worked for RealTek but not for the Cirrus driver. Of course it said there was no RealTek hardware install, which makes me think it's a Cirrus chip. Any further suggestions or thoughts would be really appreciated. This is a Mac Mini 1.66. I'm also not sure how to be able to detect what card is integrated into the system, so that would be helpful too (remembering that there's no driver installed). Even just to get the chip type would be great to confirm.

  Read the article

• SATA Backward compatibility? [closed]

  - by Fladur

  Possible Duplicate: Can I connect a SATA-II hard drive to a SATA-I connection? Hello everyone One of my system is really old, but I still use it, right now, the HDD is and old IDE drive that is starting to fail (I got to many damaged sectors) and I'm planing to replace it. The motherboard supports Serial ATA 1 and I have a real nice offer on a SATA 2 drive, can I use that drive on a SATA 1 interface (obviously with reduced speed) just like a USB 2.0 device on a 1.0 port? Thanks in advance.

  Read the article

• UNRAID V4.7: Lost write permission on Win7/Android devices

  - by JROC

  I'm currently running V4.7 and I haven't touched any of the user or share settings, and I'm periodically losing read.write permission on both my windows 7 pc and my android tablet connecting over the wireless. Sometime I can access my shares and see the folder directories, but when attempting to open a folder windows denies me access saying I don't have the proper permission. This is after I have logged in with my main account that has full read/write access of everything, same on my android device. This all started when I attempted to delete a large amount of files (8gb) to make more room and about half way through started getting permission errors. What could be causing this? Thanks

  Read the article

• UNRAID V4.7: Lost write permission on Win7/Android devices

  - by JROC

  I'm currently running V4.7 and I haven't touched any of the user or share settings, and I'm periodically losing read.write permission on both my windows 7 pc and my android tablet connecting over the wireless. Sometime I can access my shares and see the folder directories, but when attempting to open a folder windows denies me access saying I don't have the proper permission. This is after I have logged in with my main account that has full read/write access of everything, same on my android device. This all started when I attempted to delete a large amount of files (8gb) to make more room and about half way through started getting permission errors. What could be causing this? Thanks

  Read the article

• QR Codes for Files on Google Code

  - by Synetech inc.

  Hi, When you download files from Google Code now (example), in addition to the text version of the SHA1 hash, it includes a QR code of it. The device that the file was downloaded to is the one that has to hash the file. But, if it can download the file (ie, has access to the webpage), it also has access to the text version of the hash, so the QR code seems completely useless—and more work to decode when the raw text is available. How would reading the hash into a mobile phone allow you to verify the file you download to the computer? Or if you download the file to the phone, how would you use the phone to take a picture of the QR code displayed on the webpage on its own screen? Does anyone know what the point to the QR code is or how you would use it to verify the downloaded file (I don’t mean QR codes in general, but specifically in this context).

  Read the article

• Does using a single cable to connect two switches create a bottleneck?

  - by Nick

  I realise this may be a stupid question for some, but it's something I've always wondered about. Let's say we have two gigabit switches and all of the devices on the network are also gigabit. If 10 computers connected to switch A need to transfer large amounts of data to a server on Switch B (at the same time), is the maximum transfer speed of each connection limited by the bandwidth of the connection between the two switches? In other words, would each computer only be able to transfer at a speed of one gigabit divided by the 10 machines trying to use the "bridge" between switches? If so, are there any workarounds so that every device can use it's maximum speed from point to point?

  Read the article

• Windows 8.1 unable to play Music or the Audio from videos through Optical Out

  - by Zion Fox

  I am having an issue with my audio output, where any music file, and the audio side of videos are not being played through my optical audio output. I am running a Realtek HD Audio device built on Revision 1.0 on a GA-P55A-UD6 Gigabyte Board, which runs through it's optical output to an Astro A40 Mixamp, which does some upscaling before sending it to the headset. Now, notification sounds, and sounds/videos/music played through the browser or programs like Skype or games are working fine. This seems to specifically effect Foobar2000 and Media Player Classic. I have updated these two programs to their latest revisions, in addition to the soundcard drivers to no avail, and searching the error code thrown by Foobar2000: Unrecoverable playback error: The parameter is incorrect. (0x80070057) through Google returns not very helpful results, other than the one potentially mentioning DRM. This issue I am having a very hard time resolving, and am wondering if anyone here has experienced similar issues after updating.

  Read the article

• Does Juniper Networks provide keyloggers with their software?

  - by orokusaki

  I noticed that I had a "USB Mass Storage Device" plugged in when there wasn't in fact anything plugged in to any USB port. I turned it off via Windows (XP), but it's quite concerning. This was after installing Juniper Networks' software for VPN access to an IT guy's stuff. I also notice there is a service called "dsNcService.exe" which apparently is sending information over the internet (even when I'm not in VPN access). The process restarts itself when I end it. Should I be worried that this software is tracking my keystrokes and broadcasting them to my IT guy?

  Read the article

• Migrated Virtual Machine Shows Up in Both Datastores

  - by Backstage

  Hi, We're using Vsphere client 4.0.0 Build 208111 with Virtual Center Server same version and same build. I have one vm with only one disk that is shown on 2 different datastores. If I look through VMs and Templates I see only 1 vm. If I look through Datastores screen, I see it in datastore-002 and datastore-003. If I go to settings of the virtual machine on datastore-002 and check the disk, I see the path as datastore-003. How can I fix this ?

  Read the article

• ECMP Load Balancing in JUNOS

  - by SpacemanSpiff

  I'm trying to figure out how to use ECMP load balancing in JUNOS. I know this isn't the best way to load balance, but its quick and dirty and gets done what I need to. In ScreenOS this was pretty easy. Device: SRX220 JunOS: 10.3R2.11 Here's what I've got so far: routing-options { static { route 0.0.0.0/0 { next-hop [ 1.1.1.1 1.1.1.2 ]; metric 10; } } maximum-paths 2; Will that do it? Tom

  Read the article

• Moving my bcd from HDD to SSD - Windows 7

  - by lelouch

  I have windows 7 installed on my SSD, but the /boot/ and bootmgr are on my hard-drive. I want to move them to my SSD for faster booting times. So i figured that I can fix the problem using the Windows startup repair tool. I made a bootable windows 7 flash drive, and ran Windows startup repair. However, it exits with an error. I also can't see my OS in the list of installed OSs. I then tried fixing via the command prompt with bootrec /fixmbr, bootrec /fixboot, bootrec /rebuildbcd. Bootrec /rebuildbcd finds the OS, but gives me the error "The requested system device cannot be found" when i try fixing it. Does anyone know why this is failing? I read somewhere that the Windows Repair environment doesn't support a flash drive, which is why I'm getting that error. Is this true? Unforunately my dvd drive is playing up so I can't use it to test this.

  Read the article

• External Hardrive Not Reconized on Windows 7 at all

  - by Bella

  I Have a NextStar 2/5" from Vantec and its an 80G HD. I have used it many times on windows xp and it works fine. We just recently upgraded to windows 7 home premium and when I plug it in it beeps many times. I've tried all the USB plugs in my computer and its not those plugs. Haven't tried eSata because it uses a weird cable to plug into. People told me that when it beeps everything is corrupted, but works fine on xp. I tried installing the drivers online from their website and when I try it asks me to put in a cd which makes no sense because they are online drivers. When I go into device manager nothing comes up, it just acts like the HD is invisible. The beeping will stop eventually as it is plugged in, but with no result.

  Read the article

• (simple) linux HA with vmware vsphere?

  - by derhelge

  I hope my upcoming question is specific enough, and you are able and willing to support :-) We have several openSUSE VMs in an ESX-Cluster (three ESX-Servers) with an attached iSCSI-SAN. All of those Linux VMs are "single point of failure"-configured, which means in the case of a Web-Server: LAMP, storage, etc. everything on this machine. This was very simple and in case of a failure (in the last years: kernel panics or apache crashes) a simple reboot triggered by a script did it. But the problem is: How to upgrade/maintain the w(eb-)application or the underlying OS without downtime? This wasn't really managable and i did this in the early morning ;) How can i achieve a "simple" High-Availability Cluster now? I thought of: DRBD with heartbeat with 2 VMs. And for the storage a RDM (raw device mapped) LUN and change the read-write-permissions for both VMs. Is this a good idea? Anyone has a better solution?

  Read the article

• Why does storage's performance change at various queue depths?

  - by Mxx

  I'm in the market for a storage upgrade for our servers. I'm looking at benchmarks of various PCIe SSD devices and in comparisons I see that IOPS change at various queue depths. How can that be and why is that happening? The way I understand things is: I have a device with maximum (theoretical) of 100k IOPS. If my workload consistently produces 100,001 IOPS, I'll have a queue depth of 1, am I correct? However, from what I see in benchmarks some devices run slower at lower queue depths, then speedup at depth of 4-64 and then slow down again at even larger depths. Isn't queue depths a property of OS(or perhaps storage controller), so why would that affect IOPS?

  Read the article

• NFS-Root not working when booting over PXE

  - by Randy

  I am desperately trying to get a diskless client running over PXE-Boot using a NFS-Share as a root file system. I did this before some years ago but for some reason I am stucked at this since days. The TFTP-Server itself is running fine and booting a netinstaller works also fine. The kernel and initrd are loaded also but the bootprocess stops with this (screenshot) kernel panic. I'm using the squeeze standard i386-Kernel and I have prepared the initrd with this config: MODULES=most BUSYBOX=y KEYMAP=n COMPRESS=gzip BOOT=nfs DEVICE= NFSROOT=auto I also tried MODULES=netboot with the same outcome. My PXE-configuration looks like this: LABEL linux KERNEL diskless/debian-default/vmlinuz-2.6.32-5-686 APPEND root=/dev/nfs initrd=diskless/debian-default/vmlinuz-2.6.32-5-686 nfsroot=192.168.140.2:/storage/nfs-boot-images/default-squeeze ip=dhcp rw Furthermore I have captured the network communication of the client via tcpdump and learned that the client isn't even trying to connect to the NFS-share. Does anybody has got an idea what is going wrong here?

  Read the article

• Xen 4.0.1 on Ubuntu 10.10 not booting

  - by Disco

  I'm trying to get Xen 4.0.1 run as dom0 on a fresh/clean install of 10.10 desktop (x64). Followed the step by step tutorial at http://wiki.xensource.com/xenwiki/Xen4.0 I have the pvops kernel in /boot, also included the ext4 fs support by recompiling the kernel by : make -j6 linux-2.6-pvops-config CONFIGMODE=menuconfig make -j6 linux-2.6-pvops-build make -j6 linux-2.6-pvops-install Here's my grub entry : menuentry 'Xen4' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod part_msdos insmod ext2 insmod ext3 set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set 2bf3177a-92fd-4196-901a-da8d810b04b4 multiboot /xen-4.0.gz dom0_mem=1024M loglvl=all guest_loglvl=all module /vmlinuz-2.6.32.27 root=UUID=2bf3177a-92fd-4196-901a-da8d810b04b4 ro module /initrd.img-2.6.32.27 } blkid /dev/sda1 gives the : /dev/sda1: UUID="2bf3177a-92fd-4196-901a-da8d810b04b4" TYPE="ext3" My partition shemes is : /boot (ext3) / (ext4) Whatever option i've tried i end up with : mounting none on /dev failed: no such file or directory And message complaining that it cannot find the device with uuid ... It's taking my hairs out, if somone has a clue ...

  Read the article

• Serve up PC hard drive as USB mass storage

  - by sheepsimulator

  Is there a software package available that can serve up a hard-drive internal to a PC and make it available over USB to other USB Master nodes as mass storage? Ex: take your C: or /dev/hda drive on a PC (let's call the computer PC-A), and run a driver program which makes your C: or /dev/hda drive available to external devices as USB mass storage. When you'd hook up another PC (PC-B) to PC-A via USB, it would detect a USB mass storage device, which is C: or /dev/hda on PC-A. Is this even possible? EDIT: I know that there are other ways of making data on a drive available between two different computers (eg. putting PC-A's hdd in a USB-drive-enclosure, or having PC-A make the hdd available via a network share). But I'd like to know if the method that I describe above is even technically possible.

  Read the article

• Wireless driver not detected by Windows 8

  - by rksh

  I've a problem in my wireless driver on windows 8. I bought a new X500L Asus laptop and installed windows 8 on it. However the driver CD I got with the laptop doesn't support my laptop. The CD says it's designed for Windows 8.1. I tired finding Wireless driver model and finding driver online and installing and that hasn't worked either, the wireless driver is shown at the device manager as not installed. I tired live booting the computer with a live CD of Linux and that also doesn't pick up my wireless driver. Can anyone tell me how to fix it? Thanks

  Read the article

• How to detect hard disk failure?

  - by Devator

  So, one of my servers has a hard disk failure. It's running software RAID, the system locked up and according to /proc/mdstat (and /var/log/messages), it's really down: Personalities : [raid1] md2 : active raid1 sdb2[1] 104320 blocks [2/1] [_U] md5 : active raid1 sdb5[1] 2104448 blocks [2/1] [_U] md6 : active raid1 sdb6[1] 830134656 blocks [2/1] [_U] md1 : active raid1 sdb1[1] 143363968 blocks [2/1] [_U] and Nov 5 22:04:37 m38501 smartd[4467]: Device: /dev/sda, not capable of SMART self-check However when I do smartctl -H /dev/sda, it passes the test. It also passes the test with smartctl --test=short /dev/sda. So, is smartctl a broken testing tool, or am I doing something completely off?

  Read the article

• How can I apply a DSP to my microphone in windows?

  - by user16315

  I'd like to be able to run my microphone through arbitrary DSP filters--Mostly for compression and amplification, but also noise cancelation would be nice. I'd then like to take that output and put it back in a virtual audio device that I could use as input for skype, mumble, teamspeak, or any other VOIP program. With a program like Virtual Audio cable, I can do the 'fake devices' part but as far as I know it does not allow any kind of filtering inline. Does a program like this exist? Or some combination of programs that can be combined to accomplish this?

  Read the article

< Previous Page | 395 396 397 398 399 400 401 402 403 404 405 406  | Next Page >