Search Results

Search found 133 results on 6 pages for 'dnat'.

Page 4/6 | < Previous Page | 1 2 3 4 5 6  | Next Page >

  • Can I port forward to an established reverse ssh tunnel

    - by Ben Holness
    I have three computers, A, B and C A has initiated a reverse ssh tunnel to B: ssh -nTNx -p 443 -R 22222:localhost:22 [user]@[server] If I log in to B, I can use 'ssh -p 22222 localhost' and I get a login prompt for A. If I try 'ssh -p 22222 [public IP of B]', it doesn't work What I would like to be able to do is have C connect to A without needing to login to B. So from C I could 'ssh -p 22222 [public IP of B]' and I would get the login prompt for A. I am using debian and shorewall and I have a basic understanding of how things work. I have tried various combinations of REDIRECT and DNAT rules, but haven't had any luck. I have tried using the same port (22222) and a different port (forwarding 22223 from C to 22222 on localhost). Any ideas? Cheers, Ben

    Read the article

  • Iptables massive 1:1 NAT

    - by TiFFolk
    I have to connect two LANs: LAN1: 10.10.0.0/16 and LAN2: 192.168.0.0/16. I can't do simple routing, because 192.168.0.0/16 net is prohibited in LAN1, so I am thinking of using Full cone nat (1:1) to translate 192.168.x.y/16 to 10.11.x.y/16. Each translation is done by this rules: iptables -t nat -A PREROUTING -d 10.11.0.0/16 -j DNAT --to-destination 192.168.0.0/16 iptables -t nat -A POSTROUTING -s 192.168.0.0/16 -j SNAT --to-source 10.11.0.0/16 But I will have to enter 254*254*2 rules, what will, I think, result in enormous performance degradation. So, is there a way to write such one-to-one translation with minimum number of rules?

    Read the article

  • using iptables to change a destination port but keep the ip the same.

    - by Scott Chamberlain
    I am playing around with transparent proxies, The current way I am doing things is the program makes a request to a computer on port 80, I use iptables -t nat -A OUTPUT -p tcp --destination-port 80 -j REDIRECT --to-port 1234 to redirect to my proxy that I am playing with. the proxy will send out a request to port 81 (as all outbound port 80 are being fed back in to the proxy so I want to do something like iptables -t nat -A OUTPUT -p tcp --destination-port 81 -j DNAT --to-destination xxxx:80 The problem lies with the xxxx part. How do I change the destination port without changing changing the destination ip? Or am I doing this setup completely wrong, I am learning after all and constructive criticism is definitely appreciated.

    Read the article

  • how to portforward port 7300 from server A to server B

    - by Patrick van Hout
    hi, We are using Stunnel. But want to replace it is with an iptables entry if possible. 192.168.123.122:7300 need to be forwarded to 192.168.123.188:7300. So in iptables I set these two entries: [root@dev ~]# iptables -t nat -A PREROUTING -p tcp --dport 7300 -j DNAT --to-destination 192.168.123.188:7300 [root@dev ~]# iptables -A FORWARD -m state -p tcp -d 192.168.123.188 --dport 7300 --state NEW,ESTABLISHED,RELATED -j ACCEPT But it isn't working. I did check that /proc/sys/net/ipv4/conf/eth0/forwarding has the value "1" inside. Any tips or hints? thanks, Patrick

    Read the article

  • Iptables based router inside KVM virtual machine

    - by Anton
    I have KVM virtual machine (CentOS 6.2 x64), it has 2 NIC: eth0 - real external IP 1.2.3.4 (simplified example instead of real one) eth1 - local internal IP 172.16.0.1 Now I'm trying to make port mapping 1.2.3.4:80 = 172.16.0.2:80 Current iptables rules: # Generated by iptables-save v1.4.7 on Fri Jun 29 17:53:36 2012 *nat :OUTPUT ACCEPT [0:0] :PREROUTING ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -o eth0 -j MASQUERADE -A PREROUTING -p tcp -m tcp -d 1.2.3.4 --dport 80 -j DNAT --to-destination 172.16.0.2:80 COMMIT # Completed on Fri Jun 29 17:53:36 2012 # Generated by iptables-save v1.4.7 on Fri Jun 29 17:53:36 2012 *mangle :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] COMMIT # Completed on Fri Jun 29 17:53:36 2012 # Generated by iptables-save v1.4.7 on Fri Jun 29 17:53:36 2012 *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] COMMIT # Completed on Fri Jun 29 17:53:36 2012 But there is nothing works, I mean it does not forwards that port. Similar configuration without virtualization seems to be working. What am I missing? Thanks!

    Read the article

  • iptables NAT configuration

    - by Sarp Kaya
    Hello I am experiencing some issues with my iptables. Here's what I want to do: A(eth0)--------(eth0)B(eth2)---------------(eth2)C Brackets are interface names A,B and C are hosts. Now I would like to forward port number 80 of host C so that It would be accessed via host A. host A is 192.168.1.254 host C is 192.168.3.2 I intentionally ACCEPTed all FILTER chain options as the default policy because I wanted to make sure that NAT is working properly first. I enabled ip_forward. So here's what I have done: sudo iptables -A PREROUTING -t nat -p tcp - d 192.168.1.254 -j DNAT --to 192.168.3.2 However it is not working. What am I missing here?

    Read the article

  • IPTables reroute traffic not working

    - by user1307079
    I am trying to reroute incoming traffic on my server's port 80 to another server, but it is not working. This is what I tried. On the host server, I ran these: echo “1? > /proc/sys/net/ipv4/ip_forward iptables -t nat -A PREROUTING -p tcp --dport 80 -j DNAT --to-destination 38.105.20.226:80 iptables -t nat -A POSTROUTING -j MASQUERADE The server I want it to redirect to is 38.105.20.226:80, but when I go to the webserver that is on the main server, instead of showing the content of the web server on 38.105.20.226:80, it just doesn't load. I am on CentOS.

    Read the article

  • iptables question

    - by RubyFreak
    i have a small network, with one valid IP and a firewall with 3 network interfaces (LAN, WAN, DMZ). I want to enable PAT on this valid IP to redirect http traffic to a server in my DMZ. (done) I want to enable MASQ on this ip from traffic that comes from my LAN (done) I want from my LAN as well to access my http server at DMZ. (partially) Question: in the above scenario, i cannot from my LAN, to access my http server in the DMZ, since it has the IP used by the MASQ (the only valid ip that i have). What would be the best option to solve this problem? network interfaces: eth0 (WAN) eth1 (DMZ) eth2 (LAN) /sbin/iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE /sbin/iptables -A FORWARD --o eth1 -d 2.2.2.2 -p tcp --dport 80 -j ACCEPT /sbin/iptables -t nat -A PREROUTING -i eth0 -d 1.1.1.1 -p tcp --dport 80 -j DNAT --to 2.2.2.2 /sbin/iptables -A FORWARD -i eth0 -o eth1 -m state --state RELATED,ESTABLISHED -j ACCEPT /sbin/iptables -A FORWARD -i eth1 -o eth0 -j ACCEPT /sbin/iptables -A FORWARD -i eth2 -o eth0 -j ACCEPT

    Read the article

  • Cannot redirect ip traffic with iptables to new ip on linux centOS

    - by Kiwi
    today I able to migrate some of the game servers to another server and needed some help to redirect the traffic from old ip to the new one. SERVER1 1.1.1.1 ----- (internet ) ----- SERVER 2.2.2.2 I asume to use iptables to perform this, for that used this rule on my centOS box in the server1. /etc/sysctl.conf: net.ipv4.ip_forward = 1 iptables -t nat -A PREROUTING -p udp --dest 1.1.1.1 --dport 27015 -j DNAT --to-destination 2.2.2.2:27015 iptables -t nat -A POSTROUTING -j MASQUERADE iptables -t nat -A POSTROUTING -d 2.2.2.2 -p udp --dport 27015 -j SNAT --to 1.1.1.1 But the client cannot connect to the server from the old ip, the redirection don't started.

    Read the article

  • Forwarding broadcast traffic

    - by Dragos
    I have a host that receives broadcast queries on a UDP port. I would like to forward this broadcast traffic to another host from another network. Is it possible to port forwarding broadcast traffic using iptables? I have tried to specify package traffic as broadcast, but I didn't success. (-m pkttype --pkt-type broadcast). If I recive unicast traffic on that port, the forwarding succeeds. I try to forwarding using nat table.(-A POSTROUTING -j DNAT --to-destinatiox x.x.x.x) Thanks.

    Read the article

  • Iptables remote port forwarding and dynamic remote ip

    - by lbwtz2
    Hello, I want to forward a port from my remote vps to my domestic server and I am quite a newbie with iptables. The problem is that I am using a dynamic dns service to reach my home server from the internet so I don't have a fixed ip and iptables doesn't like urls. The rules I am willing to use are these: -t nat -A PREROUTING -p tcp -i eth0 -d xxx.xxx.xxx.xxx --dport 8888 -j DNAT --to myhome.tld:80 -A FORWARD -p tcp -i eth0 -d myhome.tld --dport 80 -j ACCEPT Of course I recevie a Error BAD IP ADDRESS because of myhome.tld. What can I do?

    Read the article

  • Troubles doing transparent proxy for virtual machines

    - by Dan H
    Hi iptables gurus. First here is the basic topology: Internet | Gateway | Workstation---eth0---virbr0 | +-----+-----+ | | | vm1 vm2 vm3 I need to test a traffic analyzer running on my workstation, listening on some port (say 8990) on eth0. The rule [I think] I want is "any packets leaving virbr0 going anywhere to port 80 must instead go to port 8990 on eth0". My software running on port 8990 does its own check of the NAT packet mangling to push the packets through after it inspects them. I've been banging my head on this, with different variants of: iptables -t nat -A PREROUTING -i virbr0 -p tcp --dport 80 -j DNAT \ --to 10.0.0.10:8990 And I've tried the more generic method of using the mangle table with --set-mark and ip rule add fwmark, but I'm not getting it. I guess what's confusing me is that everything runs on the same box. Thanks for any guidance.

    Read the article

  • Squid3 not working. Access denied

    - by Nitish
    I installed SQUID3 on a Linux machine with two ethernet interfaces (eth0 and eth1). I used the default settings in the squid.conf file and uncommented the two lines acl localnet src 192.168.0.0/16 and http_access allow localnet. eth0 is connected to a router, which provides Internet access. It is assigned an IP 192.168.1.2 by the router. I manually configured eth1 to have an IP address 192.168.5.1. It is connected to a switch. Systems having IP addresses 192.168.5.x are connected to this switch. I ran these two commands for NAT: iptables -t nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j DNAT --to-destination 192.168.5.1:3128 iptables -t nat -A PREROUTING -i eth0 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 But when I try to access internet from a system having IP 192.168.5.2 through the proxy I get an error that says "Access denied". What is wrong with my configuration?

    Read the article

  • Port Forwarding Using iptables on Ubuntu

    - by user141610
    This is the scenario. I have configured a web-server in MUX. Now I want to access that web-server from Internet. Ubuntu box has two interfaces, One is connected to WAN (Public IP) and another one is connected to MUX (Private IP). MUX has no option to insert default gateway. iptables -t nat -A PREROUTING -p tcp -i eth0 -d 103.x.x.x --dport 8001 -j DNAT --to-destination 192.168.1.2:8080 iptables -A FORWARD -p tcp -d 192.168.1.2 --dport 8080 -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT It does not work. Thanks...

    Read the article

  • Setting up a transparent proxy with only one box.

    - by Scott Chamberlain
    I am playing around with transparent proxies, unfortunately I do not have two machines to test it out with. The current way I am doing things is the program makes a request to a computer on port 80, I use iptables -t nat -A OUTPUT -p tcp --destination-port 80 -j REDIRECT --to-port 1234 to redirect to my proxy that I am playing with. the proxy will send out a request to port 81 (as all outbound port 80 are being fed back in to the proxy so I want to do something like iptables -t nat -A OUTPUT -p tcp --destination-port 81 -j DNAT --to-destination xxxx:80 The problem lies with the xxxx part. How do I change the destination port without changing changing the destination ip? Or am I doing this setup completely wrong, I am learning after all and constructive criticism is definitely appreciated. The machine I am using is pretty low end so I would like not not have to create a VM with a second box unless absolutely necessary.

    Read the article

  • Squid3 not working. Access denied.

    - by Nitish
    I installed SQUID3 on a Linux machine with two ethernet interfaces (eth0 and eth1). I used the default settings in the squid.conf file and uncommented the two lines acl localnet src 192.168.0.0/16 and http_access allow localnet. eth0 is connected to a router, which provides Internet access. It is assigned an IP 192.168.1.2 by the router. I manually configured eth1 to have an IP address 192.168.5.1. It is connected to a switch. Systems having IP addresses 192.168.5.x are connected to this switch. I ran these two commands for NAT: iptables -t nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j DNAT --to-destination 192.168.5.1:3128 iptables -t nat -A PREROUTING -i eth0 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 But when I try to access internet from a system having IP 192.168.5.2 through the proxy I get an error that says "Access denied". What is wrong with my configuration?

    Read the article

  • How to access vm inside a vm via VNC?

    - by can.
    For some reasons I installed virtual machines inside a virtual machine, like this: A( B( C )) where A is the physical machine, B is a vm and the network type is NAT. And C is also a virtual machine and the network type is bridged. The OSes are Ubuntu 12.04 and the hypervisors are kvm. I can access B via VNC and via ssh from A, but for C I can't use ssh because C has no IP address at the start. And I assume I can only access C via VNC. I tried something like(on A): iptables -t nat -A PREROUTING -d $ip-of-A -p tcp --dport 6500 -j DNAT --to-destination $ip-of-B:5900 (I referred to this) But it doesn't work. And I'm reading the man pages of iptables and hope someone could help :)

    Read the article

  • nat with iptables, re-connecting fail within about 3 minutes

    - by xpu
    i constructed a nat with iptables, as following: echo 1 > /proc/sys/net/ipv4/ip_forward iptables -t nat -I PREROUTING -p tcp --dport 9000 -j DNAT --to xx.xx.xx.xx iptables -t nat -I POSTROUTING -p tcp --dport 9000 -j MASQUERADE service iptables save service iptables restart the configuration worked fine, but there was a problem when i disconnected and tried to reconnect again, connection will be refused within about 2~3 minutes, after that, things go fine again. what was the problem? how do i make it to accept new connection after the old one break?

    Read the article

  • How do I map a friendly name (e.g. www.example.com) to 127.0.0.1:port# on Mac OS X

    - by Fred Finkle
    I am trying to create a demo for a class of mine and I want to configure "fake" domain names on my laptop. A previous question "Can I specify a port in an entry in my /etc/hosts on OS X?" contained an answer indicating that to do it you must use /etc/hosts plus changes to the iptables "If OS X uses iptables you could point xyz.com to some ip in the hosts file like 157.166.226.25 and then: sudo iptables -t nat -A OUTPUT -p tcp --dport 80 -d 157.166.226.25 -j DNAT --to-destination 127.0.0.1:3000 " Since OS X doesn't use iptables, how do I do the equivalent using the tools available on OS X? (the original "asker" seemed to know how to do this, so it wasn't explained). Thanks in advance.

    Read the article

  • Don't understand [0:0] iptable syntax

    - by artaxerxe
    I'm struggling with some iptables rules. I'm a newbie in iptables. I found some resources where I get the following command related to iptables. This is stored in a file that will be executed. [0:0] -A PREROUTING -s 10.1.0.0/24 -p tcp -m tcp --dport 81 -j DNAT --to-destination 10.1.0.6:3128 Can anybody explain me what does [0:0] mean? Also, some link related to this in iptables are welcome. Thanks in advance! P.S. If you need more rules, just let me know.

    Read the article

  • Can't get port forwarding to work on Ubuntu

    - by Znarkus
    I'm using my home server as NAT/router, which works well. But now I'm trying to forward port 3478, which I can't get to work. eth0 = public interface eth1 = private network $ cat /proc/sys/net/ipv4/conf/eth0/forwarding 1 $ cat /proc/sys/net/ipv4/conf/eth1/forwarding 1 Then to forward port 3478 to 10.0.0.7, I read somewhere that I should run iptables -t nat -A PREROUTING -p tcp -i eth0 --dport 3478 -j DNAT --to-destination 10.0.0.7:3478 iptables -A FORWARD -p tcp -d 10.0.0.7 --dport 3478 -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT I also ran ufw allow 3478 But testing port 3478 with http://www.canyouseeme.org/ doesn't work. Any idea what I have done wrong?

    Read the article

  • Cisco ASA Multiple Public IP

    - by KGDI
    I have a Cisco ASA5510 and articles related to ASA and mulitple Public IP says this cant be done. My question is how to best solve a scenario like this: I have 3 zones, Outside, Inside and DMZ Outside is Internet Inside is Client machines DMZ is a zone for servers related to external and internal services. My scenario is a bit more complex, but to keep things simple this will do: I want to place an Exchange server and a web server (externally reachable in the DMZ zone) The webserver uses both TCP80/443, the Exchange server uses 443 So to the problem: With the ASA only having one public IP, how would you make a DNAT to port 443 on both the internal hosts behind 1 Public IP? Usually, when i do this kind of scenario With Linux boxes i use alias Interfaces like eth0:0, eth0:1 and set 1 Public IP on each. To me this must be a pretty common scenario, any ideas on how to solve it With ASA? /KGDI

    Read the article

  • No client internet access when setting up these iptables rules

    - by Siriss
    I have read many other posts but cannot figure this out. eth0 is my external connected to a Comcast modem. The server has internet access with no issues. eth1 is internal and running DHCP for the clients. I have DHCP working just fine, all my clients can get an IP and ping the server but they cannot access the internet. I am using ISC-DHCP-SERVER and have set /etc/default/isc-dhcp-server to INTERFACE="eht1" Here is my dhcpd.conf file located in /etc/dhcp/dhcpd.conf ddns-update-style interim; ignore client-updates; subnet 10.0.10.0 netmask 255.255.255.0 { range 10.0.10.10 10.0.10.200; option routers 10.0.10.2; option subnet-mask 255.255.255.0; option domain-name-servers 208.67.222.222, 208.67.220.220; #OpenDNS # option domain-name "example.com"; default-lease-time 21600; max-lease-time 43200; authoritative; } I have made the *net.ipv4.ip_forward=1* change in /etc/sysctl.conf here is my interfaces file: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp iface eth1 inet static address 10.0.10.2 netmask 255.255.255.0 network 10.0.10.0 auto eth1 And finally- here is my iptables.conf file: # Firewall configuration written by system-config-firewall # Manual customization of this file is not recommended. *nat :PREROUTING ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -s 10.0.10.0/24 -o eth0 -j MASQUERADE #-A PREROUTING -i eth0 -p tcp --dport 59668 -j DNAT --to-destination 10.0.10.2:59668 COMMIT *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -i eth1 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 80 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 443 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 53 -j ACCEPT -A INPUT -m state --state NEW -m udp -p udp --dport 53 -j ACCEPT -A FORWARD -s 10.0.10.0/24 -o eth0 -j ACCEPT -A FORWARD -d 10.0.10.0/24 -m state --state ESTABLISHED,RELATED -i eth0 -j ACCEPT -A FORWARD -p icmp -j ACCEPT -A FORWARD -i lo -j ACCEPT -A FORWARD -i eth1 -j ACCEPT #-A FORWARD -i eth0 -m state --state NEW -m tcp -p tcp -d 10.0.10.2 --dport 59668 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT I am completely stuck. I cannot figure out why the clients cannot access the internet. Am I missing a service? Is a service not running? Any help would be greatly appreciated. I tried to be as thorough as possible but please let me know if I have missed something. Thank you!

    Read the article

  • iptables -P FORWARD DROP makes port forwarding slow

    - by Isaac
    I have three computers, linked like this: box1 (ubuntu) box2 router & gateway (debian) box3 (opensuse) [10.0.1.1] ---- [10.0.1.18,10.0.2.18,10.0.3.18] ---- [10.0.3.15] | box4, www [10.0.2.1] Among other things I want box2 to do nat and port forwarding, so that I can do ssh -p 2223 box2 to reach box3. For this I have the following iptables script: #!/bin/bash # flush iptables -F INPUT iptables -F FORWARD iptables -F OUTPUT iptables -t nat -F PREROUTING iptables -t nat -F POSTROUTING iptables -t nat -F OUTPUT # default default_action=DROP for chain in INPUT OUTPUT;do iptables -P $chain $default_action done iptables -P FORWARD DROP # allow ssh to local computer allowed_ssh_clients="10.0.1.1 10.0.3.15" for ip in $allowed_ssh_clients;do iptables -A OUTPUT -p tcp --sport 22 -d $ip -j ACCEPT iptables -A INPUT -p tcp --dport 22 -s $ip -j ACCEPT done # allow DNS iptables -A OUTPUT -p udp --dport 53 -m state \ --state NEW,ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -p udp --sport 53 -m state \ --state ESTABLISHED,RELATED -j ACCEPT # allow HTTP & HTTPS iptables -A OUTPUT -p tcp -m multiport --dports 80,443 -j ACCEPT iptables -A INPUT -p tcp -m multiport --sports 80,443 -j ACCEPT # # ROUTING # # allow routing echo 1 >/proc/sys/net/ipv4/ip_forward # nat iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE # http iptables -A FORWARD -p tcp --dport 80 -j ACCEPT iptables -A FORWARD -p tcp --sport 80 -j ACCEPT # ssh redirect iptables -t nat -A PREROUTING -p tcp -i eth1 --dport 2223 -j DNAT \ --to-destination 10.0.3.15:22 iptables -A FORWARD -p tcp --sport 22 -j ACCEPT iptables -A FORWARD -p tcp --dport 22 -j ACCEPT iptables -A FORWARD -p tcp --sport 1024:65535 -j ACCEPT iptables -A FORWARD -p tcp --dport 1024:65535 -j ACCEPT iptables -I FORWARD -j LOG --log-prefix "iptables denied: " While this works, it takes about 10 seconds to get a password promt from my ssh command. Afterwards, the connection is as responsive as could be. If I change the default policy for my FORWARD chain to "ACCEPT", then the password promt is there imediatly. I have tried analysing the logs, but I can not spot a difference in the logs for ACCEPT/DROP in my FORWARD chain. Also I have tried allowing all the unprivileged ports, as box1 uses thoses for doing ssh to box2. Any hints? (If the whole setup seems strange to you - the point of the exercise is to understand iptables ;))

    Read the article

  • Endian Destination NAT

    - by Ben Swinburne
    I have installed Endian Community Firewall 2.3 and am clearly misunderstanding/doing something wrong with it. I'm trying to create some destination NAT rules to allow incoming connections to various services within the network. Router - RED I/F - x.x.x.x Router - GREEN I/F - 192.168.11.253 ECF - RED I/F - 192.168.11.254/24 ECF - GREEN I/F - 192.168.12.254/24 Target server - 192.168.12.1 Please ignore the haphazard choice of subnets and addresses- I'm trying to quickly plop Endian into an existing network before a complete rework in 6-12 months so for now. Everything works except destination NAT, so outgoing connections are fine, the routes between the two subnets are OK etc. I want to create various incoming NATs but let's take for the sake of argument, SMTP port 25 from the Internet to Target server 192.168.12.1. I've tried almost every combination of options in the Destination NAT section to achieve this and clearly am doing something wrong. I suspect my confusion must be somewhere in the Access From and/or Target section. The rest seems OK Filter Policy = Allow Service = SMTP Protocol = TCP Port = 25 Translate to type = IP DNAT Policy = NAT Insert IP = 192.168.12.1 Port Range = 25 Enabled = Checked Position = First I can't work out what I'm doing wrong, or am I doing it right and it's just not working!? Any help would be greatly appreciated.

    Read the article

< Previous Page | 1 2 3 4 5 6  | Next Page >