Search Results

Search found 354 results on 15 pages for 'mario fritsch'.

Page 4/15 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • Ping flood attack every 5 seconds

    - by Mario
    My router's log, which is a D-Link DIR-600, shows 40 pages (and updating) of entries like: Nov 19 11:17:08 PING-FLOODING flooding attack from WAN (ip:85.250.85.11) detected. Nov 19 11:17:02 PING-FLOODING flooding attack from WAN (ip:85.131.129.176) detected. Nov 19 11:16:57 PING-FLOODING flooding attack from WAN (ip:122.107.244.152) detected. Nov 19 11:16:50 PING-FLOODING flooding attack from WAN (ip:88.103.8.96) detected. Nov 19 11:16:46 PING-FLOODING flooding attack from WAN (ip:212.142.91.106) detected. Nov 19 11:16:38 PING-FLOODING flooding attack from WAN (ip:184.170.6.63) detected. Nov 19 11:16:34 PING-FLOODING flooding attack from WAN (ip:1.239.96.192) detected. Nov 19 11:16:26 PING-FLOODING flooding attack from WAN (ip:120.29.76.184) detected. Nov 19 11:16:20 PING-FLOODING flooding attack from WAN (ip:110.77.137.228) detected. Nov 19 11:16:15 PING-FLOODING flooding attack from WAN (ip:201.141.51.210) detected. What should I do? ICMP is disabled (router does not respond to WAN pings).

    Read the article

  • Strange performance differences in read/write from/to USB flash drive

    - by Mario De Schaepmeester
    When copying files from my 8GB USB 2.0 flash drive with Windows 7 to a traditional hard drive, the average speed is between 25 and 30 MB/s. When doing the reverse, copying to the USB drive, the speed is 5MB/s average. I have tested this with about 4.5GB of files, a mixture of smaller and larger ones. The observations were the same on both FAT32 and exFAT file systems on the USB drive, NTFS on the internal hard disk. I don't think I can be mistaken in saying that flash memory has a lot higher performance than a spinning hard drive in both terms of reading and writing. For both memory types, reading should be faster than writing too. Now I wonder, how can it be that copying files from a fast read memory to a faster write memory is actually slower than copying files from a fast read memory to a slow write memory? I think that the files are stored in RAM before being copied over too, and there's caching as well, but I don't see how even that could tip the balance. It can only be in the advantage of writing to the USB drive, since it is "closer" to the SATA system than the USB port and it will receive data from the internal SATA HDD faster. Perhaps my way of thinking is all wrong or it just depends on the manufacturer of the USB pen. But I am curious.

    Read the article

  • SQL Server restore a backup results in an error.

    - by Mario
    I have a database in dev (SQL Server 2005 on Windows Server 2008) that I need to move to prod (SQL Server 2000 on Windows Server 2003). My process is as follows: Login to dev, open SQL Server Management Studio Right click on the database | Tasks | Backup. Keep all default options (full backup etc.) Move .bak file locally to prod (no network drive), login to prod, open SQL Server Enterprise Manager. Right click Databases node | All Tasks | Restore database. Change Restore as database to reflect the same database name. Click radio button 'From device'. Click 'Select Devices' Click Restore from: Add..., browse to .bak file (small - only 6mb) Now I am ready to restore the database, so I click OK and get the following error: "The media family on device 'E:...bak' is incorrectly formed. SQL Server cannot process this media family. RESTORE DATABASE is terminating abnormally." This error is immediate. I have tried a few different variations of this - restoring the db to dev machine with a different db name and log file names (where it originated), creating an empty database with the same physical path to files before and trying to restore to that, making a few different .bak files and making sure they are verified before uploading them to prod. I know for a fact the directory for the .mdf and .ldf files exist on prod, though the files themselves don't exist. If, before I click OK to restore, go to the options tab instead I get the following error: Error 3241: The media family on device 'E:...bak' is incorrectly formed. SQL Server cannot process this media family. RESTORE FILELIST is terminating abnormally. Anyone have any bright ideas?

    Read the article

  • Why my hard disk can't boot from the BIOS?

    - by Mario
    I installed a new sata DVD burner. When I turned on the machine (windows 7) it didn't boot. It can boot from a lubuntu CD. There is an option on lubuntu to boot form the first hard disk. If I select it, the machine boots normally to windows 7. So from the CD I can boot but not from the BIOS. I checked all the options more than once: boot from HD, not boot from removable, boot from USB, boot from optical. The order of the boot sequence is HD then DVD. I tried booting only with the HD; I disconnected both DVDs. I even tried recovery of the MBR: bootsect, bootrec, fixmbr, buildbcd, nt60, etc. So, the question is, does this have a reason, what's the difference between booting from the BIOS (as I think) to from the DVD?. The BIOS is intel, it has BIOS codes on the right bottom corner, it stays at 5A for a while. 5A is "Resetting PATA/SATA bus and all devices".

    Read the article

  • Automatic Remote REGEDIT?

    - by SUPER MARIO BROTHERS
    I've got a lot of computers on the domain here that do not have remote desktop enabled. I can open the command prompt and do this command: REG.exe ADD \\[the machine im doing this to]\HKLM\SYSTEM\CurrentControlSet\ Control\\"Terminal Server" /v fDenyTSConnections /t REG_DWORD /d 0 and it works perfectly fine, except for one thing - it makes a prompt asking if I'm sure I want to do this, Yes/No. How would I go about having a batch file auto-answer YES to this, so I don't have to type it every time? It wouldn't be a problem if it was just a couple hundred machines, but there's plenty more than that and it would take a while to do this by hand. Not to mention I might have to sweep a few times to make sure every computer is turned on and is affected by this.

    Read the article

  • Can PHP be run in Apache via mod_php and mod_fcgi side by side?

    - by Mario Parris
    I have an existing installation of Apache (2.2.10 Windows x86) using mod_php and PHP 5.2.6. Can I run another site in a virtual host using FastCGI and a different version of PHP, while stilling running the main site in mod_php? I've made an attempt, but when I add my FCGI settings to the virtual host container, Apache is unable to restart. httpd.conf mod_php settings: LoadModule php5_module "C:\PHP\php-5.2.17-Win32-VC6-x86\php5apache2_2.dll" AddHandler application/x-httpd-php .php PHPIniDir "C:\PHP\php-5.2.17-Win32-VC6-x86" httpd-vhosts.conf fastcgi settings: <VirtualHost *:80> DocumentRoot "C:/Inetpub/wwwroot/site-b/source/public" ServerName local.siteb.com ServerAlias local.siteb.com SetEnv PHPRC "C:\PHP\php-5.3.5-nts-Win32-VC6-x86\php.ini" FcgidInitialEnv PHPRC "C:\PHP\php-5.3.5-nts-Win32-VC6-x86" FcgidWrapper "C:\PHP\php-5.3.5-nts-Win32-VC6-x86\php-cgi.exe" .php AddHandler fcgid-script .php </VirtualHost> <Directory "C:/Inetpub/wwwroot/site-b/source/public"> Options Indexes FollowSymLinks Includes ExecCGI AllowOverride All Order allow,deny Allow from all </Directory>

    Read the article

  • External HDD is always in use when trying to safely remove

    - by Mario De Schaepmeester
    I have a WD 1TB Elements external hard drive and every time I use the Windows 7 "safely remove" feature, it gives me a dialog telling that a process is using the disk. Using Sysinternals Process Explorer and the answer on this question (find everything with the drive letter) I get the following result: What is the $Extend folder and why is it in use? How can I disable it? I cannot remove it using the command line (access denied). Edit: I've followed the instructions over here and under the registry key HKLM\SYSTEM\CurrentControlSet\Control\BackupRestore\FilesNotToBackup I have a Multi-String Value named IgnoreNTFS with data \$Extend* /s But this does not make any difference. Also this question is not about a server. Additionally I can tell that I use a program called mkv2vob to convert video files with a Matroska container into something my PS3 will play. I convert the source files straight from my external HDD, but I would expect if this program does not release the lock on the HDD, surely it cannot be locked if the process isn't even running?

    Read the article

  • Which protocol do clients use when communicating with servers in a SAN

    - by Mario De Schaepmeester
    I'm trying to wrap my head around how a SAN works and how it is implemented. If I understand this well, clients wanting to access the storage devices in a SAN need to communicate with the servers via the LAN. When the SAN is implemented with Fibre Channel, these servers are Fibre Channel compliant devices, and internally in the SAN they work with the Fibre Channel Protocol. Both data and communications are supported by Fibre Channel. But which application-layer protocol do the clients use in the LAN to communicate with the servers? Is the data simply transferred via ethernet as well? This is some part I am stuck on. I went trough a lot of sources but most sources don't really mention protocols and if they do, they only mention FCP.

    Read the article

  • negative time for a ping echo reply

    - by Mario
    I was happily pinging in the net when suddenly: Pinging X with 32 bytes of data: Reply from .235: bytes=32 time=1444ms TTL=41 Reply from .235: bytes=32 time=1767ms TTL=41 Reply from .235: bytes=32 time=1531ms TTL=41 Reply from .235: bytes=32 time=-1198187ms TTL=41 Ping statistics for .235: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 1444ms, Maximum = -1198187ms, Average = 1073443462ms A negative time for the reply. I checked wireshark and it had the same values: Time delta from previous displayed frame: -1198.187867000 seconds Time since reference or first frame: -1179.935038000 seconds I didn't change the time of the machine while pinging. This was made in my local network at home, from a XP VM in windows 7. So I blame the VM (virtualbox). But I was wondering if this strange behaviour (to me) could have a reason, or if any of you have seen this before. Thank you bye.

    Read the article

  • Webmin apache on CentOS 6.3 results in 403 forbidden, permissions are OK

    - by Mario De Schaepmeester
    First of all, I will mention that the permissions are fine for the document root directory, which is /webapps/nimbus/www/public_html The www directory contains a PHP application. PHP is a problem for later if it doesn't work, as I've tested it with a plain html file (does not work either) I just get 403 forbidden responses. The permissions are 755 on webapps and all subdirectories. I've checked other questions here and on the internet, but it was all about those permissions. Whatever info you still need, just ask, I don't know what's relevant as it's the first time ever I'm using webmin or configuring apache.

    Read the article

  • Disadvantages of enabling AHCI after Win7 install

    - by Mario De Schaepmeester
    I've formatted my notebook that has a 5400RPM HDD with ~500GB capacity. After installing Windows 7 and about half the drivers (including chipset) I began to doubt whether to go for IDE or AHCI mode for my hard drive. There used to be a lot of discussion on the internet which is better and so far I understood it was particularly helpful on SSDs. Now the general consensus seems to be that AHCI mode is best for most hard drives. I have thus enabled AHCI in the middle of configuring my notebook (rest of the drivers, necessary software etc...) Two questions: considering my HDD's spec above, should I leave it on? Is there any disadvantage of enabling it after Windows 7 and chipset drivers installation? Windows 7 version is 64 bit Home Premium.

    Read the article

  • How do I create a dynamic formula on Excel?

    - by Mario Marinato -br-
    On Excel, I have a DDE formula on B1 which reads =server|info!someText.data I want to change the formula so that someText is written on A1 and then reference it on the DDE formula. Something like =server|info!A1.data. I have tried to concatenate "A1" directly on the formula, as it is above, with no success. Some other things I tried were =server|info!A1&".data" and =server|info!indirect(A1)&".data", but had no success. Is there a way to achieve this? How?

    Read the article

  • apache url / filename with special characters

    - by Mario Delgado
    I have this url: http://domain.com/wp-content/uploads/2012/10/Hvilke-vilkår-følger-med-når-du-bestiller-nyt-bredbånd.png If I ftp/ssh or just browse to that folder (apache index feature), I see the file Hvilke-vilkår-følger-med-når-du-bestiller-nyt-bredbånd.png If I click on the link from the apache index, I can see the file, however, if I copy the URL and try to browse to it directly, I get the error: The requested URL /wp-content/uploads/2012/10/Hvilke-vilkÃ¥r-følger-med-nÃ¥r-du-bestiller-nyt-bredbÃ¥nd.png was not found on this server. Also my error log says: File does not exist: /wp-content/uploads/2012/10/Hvilke-vilk\xc3\xa5r-f\xc3\xb8lger-med-n\xc3\xa5r-du-bestiller-nyt-bredb\xc3\xa5nd.png

    Read the article

  • Low FPS in some games, but hardware not fully used

    - by Mario De Schaepmeester
    I just did a little funny experiment in the game/sim "Train Simulator 2013". I normally have good FPS in it (around 30) at full settings. What I did was make a really, really long train so that the calculations the sim needed to make were enormous (the sim is quite realistic, it takes all things into account like speed/acceleration, G-forces, comfort levels, possible wheel slip and many more, and most of those things on each carriage seperately). This resulted in only 14FPS as reported by the game, but it felt more like 8FPS or so. I have a Logitech G15 keyboard which has an LCD, and it allows me to monitor CPU/RAM and video card load on it. The strange thing is, all CPU cores were busy, but the total load was only about 60% maximum at all times. The video card was only on 30% load (possibly an important note, the memory was full, which is however not unusual for the game in question). The RAM had plenty of room and there weren't many operations as it didn't grow or shrink much. I just have the feeling that the game would run smoother if it used more of my hardware power. Why is it not doing so? I had the same in another game, The Elder Scrolls: Morrowind when using more than 100 mods (that all use scripting) and a few high res texture mods, + a full-on graphics improvement program. The engine is very old (2003), and so I thought this might be the cause (not being optimised for multithreading). I had thought of possible causes, like: The operating system doesn't let the games use all the resources. It doesn't make use of multi-threading appropriately. To eliminate the former, I tried a CPU stress tool and that got 100% CPU juice as I let it run, so the OS is not the problem. I gave its thread the "higher" priority though. My actual question In both games, I did things the engine was not really built to do or support. Can those games' framerate be limited cause of their own engine not being able to cope? What is the real reason and more importantly, can I help it? And in any case, could something actually be wrong with my hardware? It's all reasonably new, a couple of months, and I (almost) never experience any other trouble. Modern and much more demanding games work absolutely fine. Specs CPU: AMD Phenom II 965 X4 @ 3.4gHz RAM: 8GB of DDR3 RAM Video: MSI GTX560 (nVidia chip) with 1GB of GDDR5 memory OS: Windows 7 Ultimate 64 bit Nothing overclocked.

    Read the article

  • Take a regular Windows 7 clone with clonezilla (device-to-image)

    - by Mario De Schaepmeester
    I am unexperienced with cloning software and I've decided to use Clonezilla as it seemed best as freeware. I chose device image and left most options standard. I chose expert mode anyway to see what I could configure, and decided to try the lzop algorithm instead of the default one for compression. The rest was left at default. When Clonezilla asked me which partitions to clone (I chose parts to image), I chose the C:\ drive but Windows 7 also creates a 100MB partition on setup for system files (the actual boot partition?). I copied that into the image as well. The reason I didn't choose disk to image is that I also have a data partition that needs to stay intact. Now I'm simply not sure that this is the way to go, should I ever need to restore my disk image. Will Clonezilla know what to do with both partitions and will Windows 7 work perfectly after restoring? Edit: apparantly a similar question has been asked before. The link to the first article in the answer is not relevant to me since it covers a device-to-device clone. It appears the windows installation disk can repair the 100MB partition. As for Clonezilla, it copies "hidden data after the MBR" by default too. I don't know, I feel I'll be allright whether by restoring the partition with Clonezilla or repairing it with the Windows 7 disk.

    Read the article

  • Windows 7 explorer crashing trying to read external hard disk

    - by Mario De Schaepmeester
    I have a 1TB Western Digital hard drive which is almost full and last time I tried to plug it into my laptop, I got a Windows dialog saying "this hard drive needs to be formatted". I did not panic because I have experienced things like this before and I know it's often solved by simply re-inserting the drive. Now however, whenever I plug it in and try to browse it in explorer by going to "computer", the explorer process crashes after a while. I simply close explorer since it takes ages trying to read the disk and nothing happens. After searching on the internet, the best thing to do would be a chkdsk. I tried it via properties in explorer (which also took a good 5 minutes to open up), locks up as well, after waiting a couple of minutes it says there's no access to the disk so a chkdsk is not possible... I want to make clear that I always use safe removal before pulling out the USB cable. Last time however, safe removal just would not work and when trying to shut down Windows, the logoff screen just would not disappear (I've waited at least 10 minutes or so) and I powered off the PC by force. This may be the cause of the problems but the disk was still recognised immediately after that. I really don't want to format this thing because it contains C: clones of 3 computers and a lot of other stuff that I don't want to re-copy. What would be the best course of action? Update I got chkdsk working via the command line. I used the /F and /R options. I already got a bunch of lines saying "file record segment X is unreadable" or whatever it is in English, my OS is Dutch. It looks bad... Will chdsk repair these errors?

    Read the article

  • Dual Monitors don't turn off/sleep when they should

    - by Mario
    Details: Dual 25" monitors connected to HP Envy via HDMI and display port via DVI adapter. Power scheme is set up in high performance (Dim Display: Never - Turn Off Display: 15 mins - Computer Sleep: Never) Screensaver is set up to kick in after 10 mins of idle (which happens) 5 minutes later, the screensaver stops. The "Monitor Going to Sleep" notice appears on screen and monitors go to sleep briefly. All is well thus far. Suddenly, the Windows 7 alert sound when a device is unplugged is heard. Monitors then turn back on. Screens are black. Only the mouse cursor is displayed. Backlighting is back on. This only started happening after I obtained and connected the second 25" monitor a few days ago. However, I had a 24" in its place before, and this wasn't happening. Why is this happening and how do I correct this behavior? Thanks in advance.

    Read the article

  • WPF WriteableBitmap Memory Leak?

    - by Mario
    Hello, everyone! I'm trying to figure out how to release a WriteableBitmap memory. In the next section of code I fill the backbuffer of a WriteableBitmap with a really large amount of data from "BigImage" (3600 * 4800 px, just for testing) If I comment the lines where bitmap and image are equaled to null, the memory it´s not release and the application consumes ~230 MB, even when Image and bitmap are no longer used! As you can see at the end of the code its necessary to call GC.Collect() to release the memory. So the question is, what is the right way to free the memory used by a WriteableBitmap object? Is GC.Collect() the only way? Any help would be great. PS. Sorry for my bad english. private void buttonTest_Click(object sender, RoutedEventArgs e) { Image image = new Image(); image.Source = new BitmapImage(new Uri("BigImage")); WriteableBitmap bitmap = new WriteableBitmap( (BitmapSource)image.Source); bitmap.Lock(); // Bitmap processing bitmap.Unlock(); image = null; bitmap = null; GC.Collect(); }

    Read the article

  • any real MVC library in PHP (for GUI apps)

    - by mario
    I'm wondering if there are any abstraction frameworks for one of the PHP gui libraries. We have PHP-GTK, a PHP/Tk interface, and seemingly also PHP-QT. (Not tried any.) I know that writing against the raw Gtk+ interface in Python is just bearable, and it therefore seems not very enticing for PHP. I assume it's the same for Qt, and Tk is pretty low-level too. So I'm looking for something that provides a nicer object structure atop any of the three. Primarily TreeViews are always a chore and php-gtk callbacks are weird in PHP, so I'd like a simplification for that. If it eases adding the GUI/View atop my business logic without much control code, that might already help. And so since GUI apps are an area where MVC or MVP would actually make sense, I'd like to know if any library for that exists. Btw, recently rediscovered PHP interface preprocessor, but that's rather low-level and just provides a simple widget/interface abstraction for Gtk/ncurses/pdf/xhtml output.

    Read the article

  • LINQ to Entity, using a SQL LIKE operator

    - by Mario
    I have a LINQ to ENTITY query that pulls from a table, but I need to be able to create a "fuzzy" type search. So I need to add a where clause that searches by lastname IF they add the criteria in the search box (Textbox, CAN be blank --- in which case it pulls EVERYTHING). Here is what I have so far: var query = from mem in context.Member orderby mem.LastName, mem.FirstName select new { FirstName = mem.FirstName, LastName = mem.LastName, }; That will pull everything out of the Member table that is in the Entity object. Then I have an addition to the logic: sLastName = formCollection["FuzzyLastName"].ToString(); if (!String.IsNullOrEmpty(sLastName)) query = query.Where(ln => ln.LastName.Contains(sLastName)); The problem is when the search button is pressed, nothing is returned (0 results). I have run the query against the SQL Server that I expect to happen here and it returns 6 results. This is the query I expect: SELECT mem.LastName, mem.FirstName FROM Members mem WHERE mem.LastName = 'xxx' (when xxx is entered into the textbox) Anyone see anything wrong with this?

    Read the article

  • .Ajax with jQuery and MVC2

    - by Mario
    Im trying to create an ajax (post) event that will populate a table in a div on button click. I have a list of groups, when you click on a group, I would like the table to "disappear" and the members that belong to that group to "appear". My problem comes up when using jQuery's .ajax... When I click on the button, it is looking for a controller that doesnt exist, and a controller that is NOT referenced. I am, however, using AREAS (MVC2), and the area is named Member_Select where the controller is named MemberSelect. When I click on the button, I get a 404 stating it cannot find the controller Member_Select. I have examined the link button and it is set to Member_Select when clicked on, but here's the ajax call: $.ajax({ type: "POST", url: '/MemberSelect/GetMembersFromGroup', success: function(html) { $("#groupResults").html(html); } }); I havent been able to find any examples/help online. Any thoughts/suggestions/hints would be greatly appreciated. Thanks!

    Read the article

  • How to dispose a Writeable Bitmap? (WPF)

    - by Mario
    Some time ago i posted a question related to a WriteableBitmap memory leak, and though I received wonderful tips related to the problem, I still think there is a serious bug / (mistake made by me) / (Confusion) / (some other thing) here. So, here is my problem again: Suppose we have a WPF application with an Image and a button. The image's source is a really big bitmap (3600 * 4800 px), when it's shown at runtime the applicaton consumes ~90 MB. Now suppose i wish to instantiate a WriteableBitmap from the source of the image (the really big Image), when this happens the applications consumes ~220 MB. Now comes the tricky part, when the modifications to the image (through the WriteableBitmap) end, and all the references to the WriteableBitmap (at least those that I'm aware of) are destroyed (at the end of a method or by setting them to null) the memory used by the writeableBitmap should be freed and the application consumption should return to ~90 MB. The problem is that sometimes it returns, sometimes it does not. Here is a sample code: // The Image's source whas set previous to this event private void buttonTest_Click(object sender, RoutedEventArgs e) { if (image.Source != null) { WriteableBitmap bitmap = new WriteableBitmap((BitmapSource)image.Source); bitmap.Lock(); bitmap.Unlock(); //image.Source = null; bitmap = null; } } As you can see the reference is local and the memory should be released at the end of the method (Or when the Garbage collector decides to do so). However, the app could consume ~224 MB until the end of the universe. Any help would be great.

    Read the article

  • Changing values of (multiple) dropdown lists from one dropdown list in MVC

    - by Mario
    I have an MVC page, with some controls inside a form. The part I need help with: I have a bunch of dropdowns in a list. All dynamically named (drop{0}, where {0} is the id (really, its just a counter: 1,2,3,etc)). At the top of the list, I want to have another dropdown that will update ALL the dropdowns when it is changed. I've done similar things with checkboxes (check one and all are checked, etc) so I assume this can be done, hopefully just as simple. I'd prefer it to be on the client side, so once the form is submitted, the new values will be added/updated to the database. Edit: The values of ALL the dropdowns are static. They are all a list of 1-50, representing the number of cards I need to produce for a given record. This is how I did the checkbox: $("#chkSelectAll").click(function() { $(".checkbox").attr('checked', this.checked); }); Any thoughts on where to begin? Thanks!

    Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >