Search Results

Search found 506 results on 21 pages for 'mnt'.

Page 4/21 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• "fopen: No such file or directory" error

  - by Akshay Bhat

  I am getting following cryptic error: akshay@akshay-VirtualBox:/mnt/mmpp$ ./bin/metamap10 /mnt/mmpp/bin/SKRrun.10 -L 2010 /mnt/mmpp/bin/metamap10.BINARY.Linux -Z 10 --debug input.txt fopen: No such file or directory does this error implies that it cannot fopen cannot find a required file or fopen itself is nonexistent, note that both SKRrun.10 and metamap10.BINARY.Linux are present at the correct location I am using this software http://metamap.nlm.nih.gov/ on Ubuntu.

  Read the article

• Writing to Samba share as different user?

  - by Hamid Elaosta

  I have a Samba share on my NAS drive mounter as follows: mount -t smbfs -o username=backup,password=backups_password //sharebox/SVNBackup /mnt/SVNBackup I am then trying to run: sudo svnadmin dump /usr/local/svn/repos/testrepo > /mnt/SVNBackup/test1.svn but I get: bash: /mnt/SVNBackup/test1.svn: Permission Denied The backup location is setup to accept access only from the user "backup" (who doesn't exist on the local system) How do I go about solving this problem? Thanks

  Read the article

• cannot mount root filesystem on 10.04

  - by howaryoo

  I tried to apply the recommendation of question: Kernel Panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) After running that command: sudo mount --bind /dev /mnt/dev I get this error message: mount: mount point /mnt/dev does not exist fdisk -l returns /dev/sda1 /dev/sda2 /dev/sda5 do I need to mount sda2 and sda5? Edited after @psusi's comment: /dev/sda1 is the boot file system It seems that I need to mount sda2 or sda5. Here is what I tried: (I tried this on a virtual machine so the sda(s) are now vda(s) ) ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/vda: 19.3 GB, 19327352832 bytes 16 heads, 63 sectors/track, 37449 cylinders Units = cylinders of 1008 * 512 = 516096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0008eece Device Boot Start End Blocks Id System /dev/vda1 * 3 496 248832 83 Linux Partition 1 does not end on cylinder boundary. /dev/vda2 498 37448 18622465 5 Extended Partition 2 does not end on cylinder boundary. /dev/vda5 498 37448 18622464 8e Linux LVM ubuntu@ubuntu:~$ ubuntu@ubuntu:~$ ubuntu@ubuntu:~$ sudo mount -t ext4 /dev/vda5 /mnt mount: wrong fs type, bad option, bad superblock on /dev/vda5, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so ubuntu@ubuntu:~$ sudo mount -t ext2 /dev/vda5 /mnt mount: wrong fs type, bad option, bad superblock on /dev/vda5, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so ubuntu@ubuntu:~$ Any info that can help me rescue that server would be greatly appreciated!

  Read the article

• How to restore Windows7 after restore ubuntu bootloader?

  - by Mateusz Rogulski

  At first I will describe my situation in a few points: I have installed Windows7, and then Ubuntu 11.04 on my machine. Then everything works fine and at start of system I have screen from linux where I can choose the system. Then I reinstall Windows7 and install Windows 8 on other partition. Then I can choose between Win7 and win8 when I start system. Then I need my Ubuntu back so I want restore my bootloader from Ubuntu. I boot Ubuntu from USB and in terminal write this commands: sudo fdisk -l Then I get: /dev/sda1 1 13 104391 de Dell Utility /dev/sda2 14 2805 22425601 5 Rozszerzona /dev/sda3 * 2805 41968 314572800 7 HPFS/NTFS /dev/sda4 41968 60802 151282688 7 HPFS/NTFS /dev/sda5 14 2445 19530752 83 Linux /dev/sda6 2445 2805 2893824 82 Linux swap / Solaris Next commands: sudo mount /dev/sda5 /mnt sudo mount --bind /dev /mnt/dev sudo mount --bind /proc /mnt/proc sudo chroot /mnt grub-install /dev/sda I get Installation finished. No error reported.. And when I start my machine I have old Ubuntu start screen to choose system. Ubuntu works well. But There are no Windows 8 option. But my primary problem is when I choose Windows 7 I have: error: no such device ... error: no such disk so I have no idea what can I do. I really need both systems to work. Any help would be appreciated.

  Read the article

• rsync osx to linux

  - by Nick

  I did a backup to a remote nfs folder with rsync, from a MAC to a Remote Debian. The final backup is 58GB less than the original. Rsync says that everything was OK, and nothing to update. Macintosh:/Volumes/Data1 root# du -sh Produccion/ 319G Produccion/ root@Disketera:/mnt/soho_storage/samba/shares# du -sh Produccion/ 260G Produccion/ can I trust in rsync? I'm using rsync -av --stats /Volumes/Data1/Produccion/ /mnt/red/ (/mnt/red is my samba mountpoint) Some differents folders root@Disketera:/mnt/soho_storage/samba/shares/Produccion/tiposok# du -sh * 0 IndoSanBol 0 IndoSans-Bold 0 IndoSans-Italic 0 IndoSans-Light 0 IndoSans-Regular 40K PalatinoLTStd-Black.otf 40K PalatinoLTStd-BlackItalic.otf 40K PalatinoLTStd-Bold.otf 44K PalatinoLTStd-BoldItalic.otf 44K PalatinoLTStd-Italic.otf 40K PalatinoLTStd-Light.otf 40K PalatinoLTStd-LightItalic.otf 40K PalatinoLTStd-Medium.otf 40K PalatinoLTStd-MediumItalic.otf 56K PalatinoLTStd-Roman.otf 12K TCL IndoSans_mac Macintosh:/Volumes/Data1/Produccion/tiposok root# du -sh * 36K IndoSanBol 40K IndoSans-Bold 36K IndoSans-Italic 36K IndoSans-Light 36K IndoSans-Regular 40K PalatinoLTStd-Black.otf 40K PalatinoLTStd-BlackItalic.otf 40K PalatinoLTStd-Bold.otf 44K PalatinoLTStd-BoldItalic.otf 44K PalatinoLTStd-Italic.otf 40K PalatinoLTStd-Light.otf 40K PalatinoLTStd-LightItalic.otf 40K PalatinoLTStd-Medium.otf 40K PalatinoLTStd-MediumItalic.otf 56K PalatinoLTStd-Roman.otf 160K TCL IndoSans_mac

  Read the article

• ext4 loopback device, Buffer I/O Error on reboot

  - by cvb

  I am trying to mount a loopback device on my ext4 formatted ssd drive. I get these errors when I reboot on Linux kernel 2.6.38.8 Buffer I/O error on device loop1, logical block 0 Here is what I do: dd if=/dev/zero of=/mnt/s/lodev bs=4096 count=250000 mkfs.ext4 /mnt/s/lodev mount -n -o loop,rw /mnt/s/lodev /mnt/test The loopback mount is successful, but on reboot I get errors as mentioned above. Even mouting with 'sync','data=writeback' does not help. I tried to losetup a device, but see the same behavior. I also reformatted the base device and created the loopback device and mounted as above, I still see these errors. I do not see them when I format them as vfat. Appreciate any suggestions on this problem.

  Read the article

• No operating system found even when grub2 was reinstalled

  - by Cruzer

  I know there have been many variations on this question and have certainly tried to do my research. I don't really know what I'm doing so I would rather not take risks. I am trying to dual boot xubuntu and windows 7. I started out with xubuntu and just installed windows. Of course, the mbr got overwritten and windows didn't seem to recognize linux. So I booted to the live cd and rewrote the mbr. And of course, now I get the error "No Operating System Found" on startup. I have been following these tutorials to help me out. community.linuxmint.com/tutorial/view/245 unix.stackexchange.com/questions/96977/grub-wont-install ubuntuforums.org/showthread.php?t=2036730 Specifically, I ran these commands: # sdb2 is the partition with xubuntu sudo mount /dev/sdb2 /mnt # sdb1 is my boot partition sudo mount /dev/sdb1 /mnt/boot # not sure what this does, but ran it anyway... for i in /dev /dev/pts /proc /sys /run; do sudo mount -B $i /mnt$i; done sudo chroot /mnt #once chrooted grub-install /dev/sdb update-grub here's a link to my gparted https://www.dropbox.com/s/zpbbzh9z7k1l3pj/gparted.png EDIT--- didn't realize that the drive letters are different in the picture than in my code (its sda in the pic instead of sdb). I have been restarting a lot and sometimes the drive letters change and make my usb into sda.

  Read the article

• Crontab stopped unexpectedly

  - by naka

  I have following entries in the crontab: 0 0 * * * /mnt/voylla-production/releases/20131111011431/script/rubber cron --task util:rotate_logs --directory=/mnt/voylla-production/releases/20131111011431/log 0 4 * * * /mnt/voylla-production/releases/20131111011431/voylla_scripts/cj_daily.sh 0 2 * * 6 /mnt/voylla-production/releases/20131111011431/voylla_scripts/cj_saturday.sh I worked fine until today. It didn't run as scheduled after a capistrano deploy, didn't get a mail either. It worked fine earlier, and I am unable to understand what wrong. The only change that was made was the deploy, but I think it should not affect the cron. I tried using pgrep cron to see if crons is working. It gives 904 as output. Could someone please help. Thanks

  Read the article

• compiling openss7

  - by deddihp

  hello, i got an error while compiling openss7. Do you know what happen ? Thanks.... gcc -DHAVE_CONFIG_H -I. -I. -I. -DLFS=1 -imacros ./config.h -imacros ./include/sys/config.h -I. -I./include -I./include -nostdinc -iwithprefix include -DLINUX -D__KERNEL__ -I/usr/src/linux-headers-lbm-2.6.28-11-generic -I/lib/modules/2.6.28-11-generic/build/include -Iinclude2 -I/lib/modules/2.6.28-11-generic/build/include -I/lib/modules/2.6.28-11-generic/build/arch/x86/include -include /lib/modules/2.6.28-11-generic/build/include/linux/autoconf.h -Iubuntu/include -I/lib/modules/2.6.28-11-generic/build/ubuntu/include -I/lib/modules/2.6.28-11-generic/build/arch/x86/include/asm/mach-default '-DKBUILD_STR(s)=#s' '-DKBUILD_BASENAME=KBUILD_STR('`echo libLfS_specfs_a-specfs.o | sed -e 's,lib.*_a-,,;s,\.o,,;s,-,_,g'`')' -DMODULE -D__NO_VERSION__ -DEXPORT_SYMTAB -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common -Werror-implicit-function-declaration -O2 -m32 -msoft-float -mregparm=3 -freg-struct-return -mpreferred-stack-boundary=2 -march=i586 -mtune=generic -Wa,-mtune=generic32 -pipe -Wno-sign-compare -fno-asynchronous-unwind-tables -mno-sse -mno-mmx -mno-sse2 -mno-3dnow -fno-stack-protector -fno-omit-frame-pointer -fno-optimize-sibling-calls -Wdeclaration-after-statement -Wno-pointer-sign -fwrapv -ffreestanding -c -o libLfS_specfs_a-specfs.o `test -f 'src/kernel/specfs.c' || echo './'`src/kernel/specfs.c In file included from src/kernel/specfs.c:123: src/kernel/strspecfs.c: In function ‘specfs_init_cache’: src/kernel/strspecfs.c:1406: warning: passing argument 5 of ‘kmem_cache_create’ from incompatible pointer type src/kernel/strspecfs.c:1406: error: too many arguments to function ‘kmem_cache_create’ In file included from src/kernel/specfs.c:126: src/kernel/strlookup.c: In function ‘cdev_lookup’: src/kernel/strlookup.c:508: warning: format not a string literal and no format arguments src/kernel/strlookup.c:514: warning: format not a string literal and no format arguments src/kernel/strlookup.c:521: warning: format not a string literal and no format arguments src/kernel/strlookup.c: In function ‘cdrv_lookup’: src/kernel/strlookup.c:562: warning: format not a string literal and no format arguments src/kernel/strlookup.c: In function ‘fmod_lookup’: src/kernel/strlookup.c:604: warning: format not a string literal and no format arguments src/kernel/strlookup.c: In function ‘cdev_search’: src/kernel/strlookup.c:709: warning: format not a string literal and no format arguments src/kernel/strlookup.c:716: warning: format not a string literal and no format arguments src/kernel/strlookup.c: In function ‘fmod_search’: src/kernel/strlookup.c:768: warning: format not a string literal and no format arguments src/kernel/strlookup.c: In function ‘cmin_search’: src/kernel/strlookup.c:823: warning: format not a string literal and no format arguments src/kernel/strlookup.c:830: warning: format not a string literal and no format arguments src/kernel/strlookup.c:840: warning: format not a string literal and no format arguments src/kernel/strlookup.c:848: warning: format not a string literal and no format arguments In file included from src/kernel/specfs.c:129: src/kernel/strattach.c: In function ‘check_mnt’: src/kernel/strattach.c:131: error: ‘struct vfsmount’ has no member named ‘mnt_namespace’ src/kernel/strattach.c:131: error: ‘struct task_struct’ has no member named ‘namespace’ src/kernel/strattach.c: In function ‘do_fattach’: src/kernel/strattach.c:200: error: ‘struct nameidata’ has no member named ‘dentry’ src/kernel/strattach.c:200: error: ‘struct nameidata’ has no member named ‘mnt’ src/kernel/strattach.c:200: error: ‘struct nameidata’ has no member named ‘dentry’ src/kernel/strattach.c:203: error: ‘struct nameidata’ has no member named ‘mnt’ src/kernel/strattach.c:208: error: ‘struct nameidata’ has no member named ‘mnt’ src/kernel/strattach.c:208: error: ‘struct nameidata’ has no member named ‘mnt’ src/kernel/strattach.c:208: error: ‘struct nameidata’ has no member named ‘dentry’ src/kernel/strattach.c:226: error: implicit declaration of function ‘path_release’ src/kernel/strattach.c: In function ‘do_fdetach’: src/kernel/strattach.c:253: error: ‘struct nameidata’ has no member named ‘dentry’ src/kernel/strattach.c:253: error: ‘struct nameidata’ has no member named ‘mnt’ src/kernel/strattach.c:255: error: ‘struct nameidata’ has no member named ‘mnt’ src/kernel/strattach.c:257: error: ‘struct nameidata’ has no member named ‘dentry’ src/kernel/strattach.c:262: error: ‘struct nameidata’ has no member named ‘mnt’ src/kernel/strattach.c:265: error: ‘struct nameidata’ has no member named ‘mnt’ In file included from src/kernel/specfs.c:132: src/kernel/strpipe.c: In function ‘do_spipe’: src/kernel/strpipe.c:372: warning: assignment discards qualifiers from pointer target type make[4]: *** [libLfS_specfs_a-specfs.o] Error 1 make[4]: Leaving directory `/home/deddihp/dev/source/openss7-0.9.2.G/streams-0.9.2.4' make[3]: *** [all-recursive] Error 1 make[3]: Leaving directory `/home/deddihp/dev/source/openss7-0.9.2.G/streams-0.9.2.4' make[2]: *** [all] Error 2 make[2]: Leaving directory `/home/deddihp/dev/source/openss7-0.9.2.G/streams-0.9.2.4' make[1]: *** [all-recursive] Error 1 make[1]: Leaving directory `/home/deddihp/dev/source/openss7-0.9.2.G' make: *** [all] Error 2

  Read the article

• How to hide bind mounts in nautilus?

  - by Bazon

  Summary: How do I remove folders mounted via bind or bindfs in /etc/fstab from appearing as devices in nautilus left column, the "places" view? detailed: Hello, I mount various directories from my data partition via bind in /etc/fstab in my home directory, eg like this: #using bind: /mnt/sda5/bazon/Musik /home/Bazon/Musik none bind,user 0 0 #or using bindfs bindfs#/mnt/sda5/tobi/Downloads /home/tobi/Downloads fuse user 0 0 (Background: /dev/sda5 mounted to /mnt/sda5 is my old home partition, but I do not want to mount it as a home partition, as I always have at least 2 Linuxes on the computer ...) That works well, but since 12.10 every one of those items is listed in Nautilus in the left column under "Devices". (Where normally USB drives appear, etc.) This is a waste of space (as I have many of such mounts...) and so I would like to have these mounts hidden, just as it was before in 12.04. How can I do that? Thanks!

  Read the article

• 12.10: How to hide bind mounts in nautilus?

  - by Bazon

  Summary: How do I remove folders mounted via bind or bindfs in /etc/fstab from appearing as devices in nautilus left column, the "places" view? detailed: Hello, I mount various directories from my data partition via bind in /etc/fstab in my home directory, eg like this: #using bind: /mnt/sda5/bazon/Musik /home/Bazon/Musik none bind,user 0 0 #or using bindfs bindfs#/mnt/sda5/tobi/Downloads /home/tobi/Downloads fuse user 0 0 (Background: /dev/sda5 mounted to /mnt/sda5 is my old home partition, but I do not want to mount it as a home partition, as I always have at least 2 Linuxes on the computer ...) That works well, but since 12.10 every one of those items is listed in Nautilus in the left column under "Devices". (Where normally USB drives appear, etc.) This is a waste of space (as I have many of such mounts...) and so I would like to have these mounts hidden, just as it was before in 12.04. How can I do that? Thanks!

  Read the article

• Why does update-grub not find ubuntu 11.10?

  - by Klaynos

  I've recently installed ubuntu onto my laptop. With the intention of dual booting with windows 7. On installation Grub wasn't loading, the computer continued to boot straight into windows. I loaded a live cd, mounted the installed ubuntu partion (sda6) as /mnt/ and windows boot partition as /mnt/boot Following the second option here: http://ubuntuguide.net/how-to-restore-grub-2-after-reinstalling-windows-xpvistawin7 Through its entirety, so creating a new grub.cfg file. chroot /mnt update-grub Did not find ubuntu, just windows 7 and the windows recovery partition. Thinking this might be a weird quirk that as I was in ubuntu (all be it a live cd) it might not list ubuntu I restarted. Grub loaded but ubuntu was nowhere to be seen. How can I add ubuntu with Grub2? I could have fixed this myself in old grub but I'm pretty much in the dark here. Thanks

  Read the article

• Command line option to check which filesystem I am using?

  - by j-g-faustus

  Is there a command that will show which file system (ext3, ext4, FAT32, ...) the various partitions and disks are using? Similar to how sudo fdisk -l lists information about disks and partitions? Update Accepted the "mount" answer as mount works without specifying filesystem type (commenting out the relevant entries in fstab, if any): $ sudo mount /dev/sdf1 /mnt/tmp $ mount | grep /mnt/tmp /dev/sdf1 on /mnt/tmp type ext3 (rw) Found another option in ubuntuforums - blkid: # system disk $ sudo blkid /dev/sda1 /dev/sda1: UUID="...." TYPE="ext4" # USB disk: $ sudo blkid /dev/sdf1 /dev/sdf1: LABEL="backup" UUID="..." TYPE="ext3" # mdadm RAID: $ sudo blkid /dev/md0 /dev/md0: LABEL="raid" UUID="..." TYPE="ext4" Thanks for your help!

  Read the article

• Stucked in the grub command prompt

  - by user903645

  I have a windows xp os, and I ve decided to give ubuntu a shot. I installed and It when rebooting it did boot by default windows. I red several forums and after entering those commands: sudo mkdir /mnt/ubuntu sudo mount /dev/sda2 /mnt/ubuntu sudo grub-install /dev/sda --root -directory=/mnt/ubuntu after rebooting the system showed me the command grub. And I cannot get anywhere. I don t have a windows cd to fix anything. so how can I launch windows from this command grub? Thanks... I am in a real mess.

  Read the article

• Unable to mount XP share using fs-cifs from Linux

  - by MetalSearGolid

  I have a head unit that runs Linux that is connected to my PC via an Ethernet cable. I have a Windows XP share on this PC that the head unit needs to be able to mount, however, when mounting using the following command, it fails. Here is the command that fails, along with the verbose output: # fs-cifs -vvvvvvvvv -l //CUMBRIA-XP:192.168.1.2:/hnet /mnt/net cifs[2158679-1]: starting... cifs[2158679-1]: user is to input both name & passwd. cifs[2158679-1]: server [192.168.1.2] share [hnet] prefix [/mnt/net] user [nu ll] passwd [null] Welcome: 192.168.1.2(:/hnet) -> /mnt/net Username:headunit cifs[2158679-1]: user name: headunit length 8 cifs[2158679-1]: new server Password: cifs[2158679-1]: establishing connection to (192.168.1.2)CUMBRIA-XP cifs[2158679-1]: session request: 192.168.1.2:CUMBRIA-XP -> localhost cifs[2158679-1]: negotiating smb dialect cifs[2158679-1]: skey(idx=2): 00000000, challenge:(8), 6137bfa2 f2d7803b cifs[2158679-1]: negotiation: success with dialect=2 cifs[2158679-1]: logging headunit on 192.168.1.2 cifs[2158679-1]: new packet cifs[2158679-1]: returning: mid 0 status= 0 cifs[2158679-1]: smb_logon successful: dialect 2 enpass 1 cifs[2158679-1]: mounting 192.168.1.2:/hnet cifs[2158679-1]: returning: mid 1 status= 13 cifs[2158679-1]: smb_mount: Bad file descriptor cifs[2158679-1]: try upper case share. cifs[2158679-1]: session request: 192.168.1.2:CUMBRIA-XP -> localhost cifs[2158679-1]: negotiating smb dialect cifs[2158679-1]: skey(idx=2): 00000000, challenge:(8), 2d3e910f e3e148c4 cifs[2158679-1]: negotiation: success with dialect=2 cifs[2158679-1]: logging headunit on 192.168.1.2 cifs[2158679-1]: returning: mid 2 status= 0 cifs[2158679-1]: smb_logon successful: dialect 2 enpass 1 cifs[2158679-1]: mounting 192.168.1.2:/HNET cifs[2158679-1]: returning: mid 3 status= 13 cifs[2158679-1]: smb_mount: Bad file descriptor cifs[2158679-1]: mount failed. cifs[2158679-1]: io_mount: smb_connection failed: Bad file descriptor io_mount: Bad file descriptor cifs[2158679-1]: user is to input both name & passwd. fs-cifs: missing arguments, or all mount attempts failed. run "use fs-cifs" or "fs-cifs -h" for help. Any ideas? It is worthy to note that /mnt does not exist on the filesystem, but I was told by the company who gave us these units that fs-cifs should automatically create the /mnt/net folders if they don't exist.

  Read the article

• Kickstart based installation of RHEL 6.4 from USB

  - by Peter

  I want to setup some brand new servers with RHEL 6.4. Servers do not have DVD, so, I have to use USB for the installation. I already have a custom ISO with a kickstart file that I use on servers with DVD flawlessly. I used iso2usb to move the ISO t? my USB. When I boot from the USB, the ks file is found, anaconda starts, but then stops with the following error: "The installation source given by device ['sda1'] could not be found. Please check your parameters and try again" Notes: The USB IS the sda. My custom ISO file is renamed to linux.iso from iso2usb and it is present in the root directory of the USB. Kickstart file has the following entry: harddrive --partition=sda1 --dir=/ Please help me to automate the installation with kickstart. Edit 1: This the anaconda.log file: 09:01:57,029 INFO : no /etc/zfcp.conf; not configuring zfcp 09:01:57,259 INFO : created new libuser.conf at /tmp/libuser.4rAbps with instPath="/mnt/sysimage" 09:01:57,259 INFO : anaconda called with cmdline = ['/usr/bin/anaconda', '--stage2', 'hd:sda1:///images/install.img', '--dlabel', '--kickstart', '/tmp/ks.cfg', '--graphical', '--selinux', '--lang', 'en_US.UTF-8', '--keymap', 'us', '--repo', 'hd:sda1:/'] 09:01:57,260 INFO : Display mode = g 09:01:57,260 INFO : Default encoding = utf-8 09:01:59,444 DEBUG : X server has signalled a successful start. 09:01:59,446 INFO : Starting window manager, pid 1345. 09:01:59,537 INFO : Starting graphical installation. 09:01:59,741 INFO : Detected 7968M of memory 09:01:59,741 INFO : Swap attempt of 7968M 09:02:00,840 INFO : ISCSID is /usr/sbin/iscsid 09:02:00,840 INFO : no initiator set Edit 2: This is the part of anaconda log that indicates that it found the USB etc: 09:01:47,918 INFO : starting STEP_STAGE2 09:01:47,918 INFO : partition is sda1, dir is //images/install.img 09:01:47,918 INFO : mounting device sda1 for hard drive install 09:01:48,005 INFO : Path to stage2 image is /mnt/isodir///images/install.img 09:01:54,214 INFO : mounted loopback device /mnt/runtime on /dev/loop0 as /tmp/install.img 09:01:54,214 INFO : Looking for updates for HD in /mnt/isodir///images/updates.img 09:01:54,214 INFO : Looking for product for HD in /mnt/isodir///images/product.img 09:01:54,227 INFO : got stage2 at url hd:sda1:///images/install.img 09:01:54,254 INFO : Loading SELinux policy 09:01:54,700 INFO : getting ready to spawn shell now 09:01:54,975 INFO : Running anaconda script /usr/bin/anaconda 09:01:56,882 INFO : _Fedora is the highest priority installclass, using it 09:01:56,921 INFO : Running kickstart %%pre script(s) 09:01:56,922 WARNING : '/bin/sh' specified as full path 09:01:56,926 INFO : All kickstart %%pre script(s) have been run

  Read the article

• Linux software RAID6: 3 drives offline - how to force online?

  - by Ole Tange

  This is similar to 3 drives fell out of Raid6 mdadm - rebuilding? except that it is not due to a failing cable. Instead the 3rd drive fell offline during rebuild of another drive. The drive failed with: kernel: end_request: I/O error, dev sdc, sector 293732432 kernel: md/raid:md0: read error not correctable (sector 293734224 on sdc). After rebooting both these sectors and the sectors around them are fine. This leads me to believe the error is intermittent and thus the device simply took too long to error correct the sector and remap it. I expect that no data was written to the RAID after it failed. Therefore I hope that if I can kick the last failing device online that the RAID is fine and that the xfs_filesystem is OK, maybe with a few missing recent files. Taking a backup of the disks in the RAID takes 24 hours, so I would prefer that the solution works the first time. I have therefore set up a test scenario: export PRE=3 parallel dd if=/dev/zero of=/tmp/raid${PRE}{} bs=1k count=1000k ::: 1 2 3 4 5 parallel mknod /dev/loop${PRE}{} b 7 ${PRE}{} \; losetup /dev/loop${PRE}{} /tmp/raid${PRE}{} ::: 1 2 3 4 5 mdadm --create /dev/md$PRE -c 4096 --level=6 --raid-devices=5 /dev/loop${PRE}[12345] cat /proc/mdstat mkfs.xfs -f /dev/md$PRE mkdir -p /mnt/disk2 umount -l /mnt/disk2 mount /dev/md$PRE /mnt/disk2 seq 1000 | parallel -j1 mkdir -p /mnt/disk2/{}\;cp /bin/* /mnt/disk2/{}\;sleep 0.5 & mdadm --fail /dev/md$PRE /dev/loop${PRE}3 /dev/loop${PRE}4 cat /proc/mdstat # Assume reboot so no process is using the dir kill %1; sync & kill %1; sync & # Force fail one too many mdadm --fail /dev/md$PRE /dev/loop${PRE}1 parallel --tag -k mdadm -E ::: /dev/loop${PRE}? | grep Upda # loop 2,5 are newest. loop1 almost newest => force add loop1 Next step is to add loop1 back - and this is where I am stuck. After that do a xfs-consistency check. When that works, check that the solution also works on real devices (such a 4 USB sticks).

  Read the article

• Improving Manageability of Virtual Environments

  - by Jeff Victor

  Boot Environments for Solaris 10 Branded Zones Until recently, Solaris 10 Branded Zones on Solaris 11 suffered one notable regression: Live Upgrade did not work. The individual packaging and patching tools work correctly, but the ability to upgrade Solaris while the production workload continued running did not exist. A recent Solaris 11 SRU (Solaris 11.1 SRU 6.4) restored most of that functionality, although with a slightly different concept, different commands, and without all of the feature details. This new method gives you the ability to create and manage multiple boot environments (BEs) for a Solaris 10 Branded Zone, and modify the active or any inactive BE, and to do so while the production workload continues to run. Background In case you are new to Solaris: Solaris includes a set of features that enables you to create a bootable Solaris image, called a Boot Environment (BE). This newly created image can be modified while the original BE is still running your workload(s). There are many benefits, including improved uptime and the ability to reboot into (or downgrade to) an older BE if a newer one has a problem. In Solaris 10 this set of features was named Live Upgrade. Solaris 11 applies the same basic concepts to the new packaging system (IPS) but there isn't a specific name for the feature set. The features are simply part of IPS. Solaris 11 Boot Environments are not discussed in this blog entry. Although a Solaris 10 system can have multiple BEs, until recently a Solaris 10 Branded Zone (BZ) in a Solaris 11 system did not have this ability. This limitation was addressed recently, and that enhancement is the subject of this blog entry. This new implementation uses two concepts. The first is the use of a ZFS clone for each BE. This makes it very easy to create a BE, or many BEs. This is a distinct advantage over the Live Upgrade feature set in Solaris 10, which had a practical limitation of two BEs on a system, when using UFS. The second new concept is a very simple mechanism to indicate the BE that should be booted: a ZFS property. The new ZFS property is named com.oracle.zones.solaris10:activebe (isn't that creative? ). It's important to note that the property is inherited from the original BE's file system to any BEs you create. In other words, all BEs in one zone have the same value for that property. When the (Solaris 11) global zone boots the Solaris 10 BZ, it boots the BE that has the name that is stored in the activebe property. Here is a quick summary of the actions you can use to manage these BEs: To create a BE: Create a ZFS clone of the zone's root dataset To activate a BE: Set the ZFS property of the root dataset to indicate the BE To add a package or patch to an inactive BE: Mount the inactive BE Add packages or patches to it Unmount the inactive BE To list the available BEs: Use the "zfs list" command. To destroy a BE: Use the "zfs destroy" command. Preparation Before you can use the new features, you will need a Solaris 10 BZ on a Solaris 11 system. You can use these three steps - on a real Solaris 11.1 server or in a VirtualBox guest running Solaris 11.1 - to create a Solaris 10 BZ. The Solaris 11.1 environment must be at SRU 6.4 or newer. Create a flash archive on the Solaris 10 system s10# flarcreate -n s10-system /net/zones/archives/s10-system.flar Configure the Solaris 10 BZ on the Solaris 11 system s11# zonecfg -z s10z Use 'create' to begin configuring a new zone. zonecfg:s10z create -t SYSsolaris10 zonecfg:s10z set zonepath=/zones/s10z zonecfg:s10z exit s11# zoneadm list -cv ID NAME STATUS PATH BRAND IP 0 global running / solaris shared - s10z configured /zones/s10z solaris10 excl Install the zone from the flash archive s11# zoneadm -z s10z install -a /net/zones/archives/s10-system.flar -p You can find more information about the migration of Solaris 10 environments to Solaris 10 Branded Zones in the documentation. The rest of this blog entry demonstrates the commands you can use to accomplish the aforementioned actions related to BEs. New features in action Note that the demonstration of the commands occurs in the Solaris 10 BZ, as indicated by the shell prompt "s10z# ". Many of these commands can be performed in the global zone instead, if you prefer. If you perform them in the global zone, you must change the ZFS file system names. Create The only complicated action is the creation of a BE. In the Solaris 10 BZ, create a new "boot environment" - a ZFS clone. You can assign any name to the final portion of the clone's name, as long as it meets the requirements for a ZFS file system name. s10z# zfs snapshot rpool/ROOT/zbe-0@snap s10z# zfs clone -o mountpoint=/ -o canmount=noauto rpool/ROOT/zbe-0@snap rpool/ROOT/newBE cannot mount 'rpool/ROOT/newBE' on '/': directory is not empty filesystem successfully created, but not mounted You can safely ignore that message: we already know that / is not empty! We have merely told ZFS that the default mountpoint for the clone is the root directory. List the available BEs and active BE Because each BE is represented by a clone of the rpool/ROOT dataset, listing the BEs is as simple as listing the clones. s10z# zfs list -r rpool/ROOT NAME USED AVAIL REFER MOUNTPOINT rpool/ROOT 3.55G 42.9G 31K legacy rpool/ROOT/zbe-0 1K 42.9G 3.55G / rpool/ROOT/newBE 3.55G 42.9G 3.55G / The output shows that two BEs exist. Their names are "zbe-0" and "newBE". You can tell Solaris that one particular BE should be used when the zone next boots by using a ZFS property. Its name is com.oracle.zones.solaris10:activebe. The value of that property is the name of the clone that contains the BE that should be booted. s10z# zfs get com.oracle.zones.solaris10:activebe rpool/ROOT NAME PROPERTY VALUE SOURCE rpool/ROOT com.oracle.zones.solaris10:activebe zbe-0 local Change the active BE When you want to change the BE that will be booted next time, you can just change the activebe property on the rpool/ROOT dataset. s10z# zfs get com.oracle.zones.solaris10:activebe rpool/ROOT NAME PROPERTY VALUE SOURCE rpool/ROOT com.oracle.zones.solaris10:activebe zbe-0 local s10z# zfs set com.oracle.zones.solaris10:activebe=newBE rpool/ROOT s10z# zfs get com.oracle.zones.solaris10:activebe rpool/ROOT NAME PROPERTY VALUE SOURCE rpool/ROOT com.oracle.zones.solaris10:activebe newBE local s10z# shutdown -y -g0 -i6 After the zone has rebooted: s10z# zfs get com.oracle.zones.solaris10:activebe rpool/ROOT rpool/ROOT com.oracle.zones.solaris10:activebe newBE local s10z# zfs mount rpool/ROOT/newBE / rpool/export /export rpool/export/home /export/home rpool /rpool Mount the original BE to see that it's still there. s10z# zfs mount -o mountpoint=/mnt rpool/ROOT/zbe-0 s10z# ls /mnt Desktop export platform Documents export.backup.20130607T214951Z proc S10Flar home rpool TT_DB kernel sbin bin lib system boot lost+found tmp cdrom mnt usr dev net var etc opt Patch an inactive BE At this point, you can modify the original BE. If you would prefer to modify the new BE, you can restore the original value to the activebe property and reboot, and then mount the new BE to /mnt (or another empty directory) and modify it. Let's mount the original BE so we can modify it. (The first command is only needed if you haven't already mounted that BE.) s10z# zfs mount -o mountpoint=/mnt rpool/ROOT/zbe-0 s10z# patchadd -R /mnt -M /var/sadm/spool 104945-02 Note that the typical usage will be: Create a BE Mount the new (inactive) BE Use the package and patch tools to update the new BE Unmount the new BE Reboot Delete an inactive BE ZFS clones are children of their parent file systems. In order to destroy the parent, you must first "promote" the child. This reverses the parent-child relationship. (For more information on this, see the documentation.) The original rpool/ROOT file system is the parent of the clones that you create as BEs. In order to destroy an earlier BE that is that parent of other BEs, you must first promote one of the child BEs to be the ZFS parent. Only then can you destroy the original BE. Fortunately, this is easier to do than to explain: s10z# zfs promote rpool/ROOT/newBE s10z# zfs destroy rpool/ROOT/zbe-0 s10z# zfs list -r rpool/ROOT NAME USED AVAIL REFER MOUNTPOINT rpool/ROOT 3.56G 269G 31K legacy rpool/ROOT/newBE 3.56G 269G 3.55G / Documentation This feature is so new, it is not yet described in the Solaris 11 documentation. However, MOS note 1558773.1 offers some details. Conclusion With this new feature, you can add and patch packages to boot environments of a Solaris 10 Branded Zone. This ability improves the manageability of these zones, and makes their use more practical. It also means that you can use the existing P2V tools with earlier Solaris 10 updates, and modify the environments after they become Solaris 10 Branded Zones.

  Read the article

• Oracle Certification and virtualization Solutions.

  - by scoter

  As stated in official MOS ( My Oracle Support ) document 249212.1 support for Oracle products on non-Oracle VM platforms follow exactly the same stance as support for VMware and, so, the only x86 virtualization software solution certified for any Oracle product is "Oracle VM". Based on the fact that: Oracle VM is totally free ( you have the option to buy Oracle-Support ) Certified is pretty different from supported ( OracleVM is certified, others could be supported ) With Oracle VM you may not require to reproduce your issue(s) on physical server Oracle VM is the only x86 software solution that allows hard-partitioning *** *** see details to these Oracle public links: http://www.oracle.com/technetwork/server-storage/vm/ovm-hardpart-168217.pdf http://www.oracle.com/us/corporate/pricing/partitioning-070609.pdf people started asking to migrate from third party virtualization software (ex. RH KVM, VMWare) to Oracle VM. Migrating RH KVM guest to Oracle VM. OracleVM has a built-in P2V utility ( Official Documentation ) but in some cases we can't use it, due to : network inaccessibility between hypervisors ( KVM and OVM ) network slowness between hypervisors (KVM and OVM) size of the guest virtual-disks Here you'll find a step-by-step guide to "manually" migrate a guest machine from KVM to OVM. 1. Verify source guest characteristics. Using KVM web console you can verify characteristics of the guest you need to migrate, such as: CPU Cores details Defined Memory ( RAM ) Name of your guest Guest operating system Disks details ( number and size ) Network details ( number of NICs and network configuration ) 2. Export your guest in OVF / OVA format.  The export from Redhat KVM ( kernel virtual machine ) will create a structured export of your guest: [root@ovmserver1 mnt]# lltotal 12drwxrwx--- 5 36 36 4096 Oct 19 2012 b8296fca-13c4-4841-a50f-773b5139fcee b8296fca-13c4-4841-a50f-773b5139fcee is the ID of the guest exported from RH-KVM [root@ovmserver1 mnt]# cd b8296fca-13c4-4841-a50f-773b5139fcee/[root@ovmserver1 b8296fca-13c4-4841-a50f-773b5139fcee]# ls -ltrtotal 12drwxr-x--- 4 36 36 4096 Oct 19  2012 masterdrwxrwx--- 2 36 36 4096 Oct 29  2012 dom_mddrwxrwx--- 4 36 36 4096 Oct 31  2012 images images contains your virtual-disks exported [root@ovmserver1 b8296fca-13c4-4841-a50f-773b5139fcee]# cd images/[root@ovmserver1 images]# ls -ltratotal 16drwxrwx--- 5 36 36 4096 Oct 19  2012 ..drwxrwx--- 2 36 36 4096 Oct 31  2012 d4ef928d-6dc6-4743-b20d-568b424728a5drwxrwx--- 2 36 36 4096 Oct 31  2012 4b241ea0-43aa-4f3b-ab7d-2fc633b491a1drwxrwx--- 4 36 36 4096 Oct 31  2012 .[root@ovmserver1 images]# cd d4ef928d-6dc6-4743-b20d-568b424728a5/[root@ovmserver1 d4ef928d-6dc6-4743-b20d-568b424728a5]# ls -ltotal 5169092-rwxr----- 1 36 36 187904819200 Oct 31  2012 4c03b1cf-67cc-4af0-ad1e-529fd665dac1-rw-rw---- 1 36 36          341 Oct 31  2012 4c03b1cf-67cc-4af0-ad1e-529fd665dac1.meta[root@ovmserver1 d4ef928d-6dc6-4743-b20d-568b424728a5]# file 4c03b1cf-67cc-4af0-ad1e-529fd665dac14c03b1cf-67cc-4af0-ad1e-529fd665dac1: LVM2 (Linux Logical Volume Manager) , UUID: sZL1Ttpy0vNqykaPahEo3hK3lGhwspv 4c03b1cf-67cc-4af0-ad1e-529fd665dac1 is the first exported disk ( physical volume ) [root@ovmserver1 d4ef928d-6dc6-4743-b20d-568b424728a5]# cd ../4b241ea0-43aa-4f3b-ab7d-2fc633b491a1/[root@ovmserver1 4b241ea0-43aa-4f3b-ab7d-2fc633b491a1]# ls -ltotal 5568076-rwxr----- 1 36 36 107374182400 Oct 31  2012 9020f2e1-7b8a-4641-8f80-749768cc237a-rw-rw---- 1 36 36          341 Oct 31  2012 9020f2e1-7b8a-4641-8f80-749768cc237a.meta[root@ovmserver1 4b241ea0-43aa-4f3b-ab7d-2fc633b491a1]# file 9020f2e1-7b8a-4641-8f80-749768cc237a9020f2e1-7b8a-4641-8f80-749768cc237a: x86 boot sector; partition 1: ID=0x83, active, starthead 1, startsector 63, 401562 sectors; partition 2: ID=0x82, starthead 0, startsector 401625, 65529135 sectors; startsector 63, 401562 sectors; partition 2: ID=0x82, starthead 0, startsector 401625, 65529135 sectors; partition 3: ID=0x83, starthead 254, startsector 65930760, 8385930 sectors; partition 4: ID=0x5, starthead 254, startsector 74316690, 135395820 sectors, code offset 0x48 9020f2e1-7b8a-4641-8f80-749768cc237a is the second exported disk, with partition 1 bootable 3. Prepare the new guest on Oracle VM. By Ovm-Manager we can prepare the guest where we will move the exported virtual-disks; under the Tab "Servers and VMs": click on  and create your guest with parameters collected before (point 1): - add NICs on different networks: - add virtual-disks; in this case we add two disks of 1.0 GB each one; we will extend the virtual disk copying the source KVM virtual-disk ( see next steps ) - verify virtual-disks created ( under Repositories tab ) 4. Verify OVM virtual-disks names. [root@ovmserver1 VirtualMachines]# grep -r hyptest_rdbms * 0004fb0000060000a906b423f44da98e/vm.cfg:OVM_simple_name = 'hyptest_rdbms' [root@ovmserver1 VirtualMachines]# cd 0004fb0000060000a906b423f44da98e [root@ovmserver1 0004fb0000060000a906b423f44da98e]# more vm.cfgvif = ['mac=00:21:f6:0f:3f:85,bridge=0004fb001089128', 'mac=00:21:f6:0f:3f:8e,bridge=0004fb00101971d'] OVM_simple_name = 'hyptest_rdbms' vnclisten = '127.0.0.1' disk = ['file:/OVS/Repositories/0004fb00000300004f17b7368139eb41/ VirtualDisks/0004fb000012000097c1bfea9834b17d.img,xvda,w', 'file:/OVS/Repositories/0004fb00000300004f17b7368139eb41/VirtualDisks/ 0004fb0000120000cde6a11c3cb1d0be.img,xvdb,w'] vncunused = '1' uuid = '0004fb00-0006-0000-a906-b423f44da98e' on_reboot = 'restart' cpu_weight = 27500 memory = 32768 cpu_cap = 0 maxvcpus = 8 OVM_high_availability = True maxmem = 32768 vnc = '1' OVM_description = '' on_poweroff = 'destroy' on_crash = 'restart' name = '0004fb0000060000a906b423f44da98e' guest_os_type = 'linux' builder = 'hvm' vcpus = 8 keymap = 'en-us' OVM_os_type = 'Oracle Linux 5' OVM_cpu_compat_group = '' OVM_domain_type = 'xen_hvm' disk2 ovm ==> /OVS/Repositories/0004fb00000300004f17b7368139eb41/VirtualDisks/ 0004fb0000120000cde6a11c3cb1d0be.img disk1 ovm ==> /OVS/Repositories/0004fb00000300004f17b7368139eb41/VirtualDisks/ 0004fb000012000097c1bfea9834b17d.img Summarizing disk1 --source ==> /mnt/b8296fca-13c4-4841-a50f-773b5139fcee/images/4b241ea0-43aa-4f3b-ab7d-2fc633b491a1/9020f2e1-7b8a-4641-8f80-749768cc237a disk1 --dest ==> /OVS/Repositories/0004fb00000300004f17b7368139eb41/VirtualDisks/ 0004fb000012000097c1bfea9834b17d.img disk2 --source ==> /mnt/b8296fca-13c4-4841-a50f-773b5139fcee/images/d4ef928d-6dc6-4743-b20d-568b424728a5/4c03b1cf-67cc-4af0-ad1e-529fd665dac1 disk2 --dest ==> /OVS/Repositories/0004fb00000300004f17b7368139eb41/VirtualDisks/ 0004fb0000120000cde6a11c3cb1d0be.img 5. Copy KVM exported virtual-disks to OVM virtual-disks. Keeping your Oracle VM guest stopped you can copy KVM exported virtual-disks to OVM virtual-disks; what I did is only to locally mount the filesystem containing the exported virtual-disk ( by an usb device ) on my OVS; the copy automatically resize OVM virtual-disks ( previously created with a size of 1GB ) . nohup cp /mnt/b8296fca-13c4-4841-a50f-773b5139fcee/images/4b241ea0-43aa-4f3b-ab7d-2fc633b491a1/9020f2e1-7b8a-4641-8f80-749768cc237a /OVS/Repositories/0004fb00000300004f17b7368139eb41/VirtualDisks/0004fb000012000097c1bfea9834b17d.img & nohup cp /mnt/b8296fca-13c4-4841-a50f-773b5139fcee/images/d4ef928d-6dc6-4743-b20d-568b424728a5/4c03b1cf-67cc-4af0-ad1e-529fd665dac1 /OVS/Repositories/0004fb00000300004f17b7368139eb41/VirtualDisks/0004fb0000120000cde6a11c3cb1d0be.img & 7. When copy completed refresh repository to aknowledge the new-disks size. 7. After "refresh repository" is completed, start guest machine by Oracle VM manager. After the first start of your guest: - verify that you can see all disks and partitions - verify that your guest is network reachable ( MAC Address of your NICs changed ) Eventually you can also evaluate to convert your guest to PVM ( Paravirtualized virtual Machine ) following official Oracle documentation. Ciao Simon COTER ps: next-time I'd like to post an article reporting how to manually migrate Virtual-Iron guests to OracleVM.  Comments and corrections are welcome. 

  Read the article

• Mounting Nexus 7 on Ubuntu 12.04 through

  - by Pomario

  I would like to transfer files between my Ubuntu 12.04 and Nexus 7 (Android 4.2) I have followed another post precisely. BUT upon... mount /mnt/nexus7 I get... Android device detected, assigning default bug flags.Listing File Information on Device with name: (NULL) and even doing an "ls" in "/mnt" generates... ls: cannot access nexus7: Transport endpoint is not connected Ideas why that is happening???

  Read the article

• Mounting Nexus 7 on Ubuntu 12.04 through USB?

  - by Pomario

  I would like to transfer files between my Ubuntu 12.04 and Nexus 7 (Android 4.2) I have followed another post carefully. BUT upon... mount /mnt/nexus7 I get... Android device detected, assigning default bug flags.Listing File Information on Device with name: (NULL) and even doing an "ls" in "/mnt" generates... ls: cannot access nexus7: Transport endpoint is not connected Ideas why that is happening???

  Read the article

• What is the correct fstab entry for automounting a remote filesystem?

  - by user101815

  I'm running Kubuntu 13.10 and I'm trying to arrange for a remote filesystem to be automounted on startup. I have the following entry for it in fstab: hpmediavault:/shares/Volume1/FileShare /mnt/mediavault nfs auto,noatime,nolock,bg,nfsvers=3,intr,tcp,actimeo=1800 0 0 I can mount it perfectly well with sudo mount /mnt/mediavault But what does it take so that it will be mounted on startup with no explicit action on my part?

  Read the article

• Arch linux - strange behaviour after installing fglrx

  - by kosto

  I have a problem with drivers on arch linux. I installed catalyst through unnoficial catalyst repo as wiki says. pacman -S catalyst catalyst-utils aticonfig --initial After this operation i rebooted the system. KDM loaded succesfully, but when i tried to switch to console (ctrl+alt+1/2/3) i saw only some strange dots, like pixels from the text were splitted on the whole screen. I was able to go back to kdm and enter the account details tho. This gave me a hang just before kde loaded. Here's a video where i'm showing above actions. Anybody knows what caused the problem? I can still chroot to fix some issues. Thanks for interest. http://glothriel.org/arch/arch_problem.ogg same thing on gnome / gdm, that's my second try on installing catalyst on arch. Open drivers suck the battery 2x faster. ___________EDIT_____________ Ok, i found a sollution, so i'm posting if someone else shares my problem. Catalyst does not support KMS, so you need to disable it from grub. You must know where are your /etc and /boot paritions mounted. If you have only one partition for / it's even simplier. Mount / on /mnt mount /dev/sdaX /mnt where X is number of the partition where is your / installed arch-chroot /mnt nano /etc/default/grub and add line: GRUB_CMDLINE_LINUX="nomodeset" save and quit then run (this will delete your windows grub configuration) grub-mkconfig -o /boot/grub/grub.cfg exit umount /mnt reboot

  Read the article

• ssh without password does not work for some users

  - by joshxdr

  I have a new RHEL4 Linux box that I am using to copy data to old Solaris 2.6 and RHEL3 Linux boxes with scp. I have found that with the same setup, it works for some users but not for others. For user jane, this works fine: jane@host1$ ssh -v remhost debug1: Next authentication method: publickey debug1: Trying private key: /mnt/home/osborjo/.ssh/identity debug1: Offering public key: /mnt/home/osborjo/.ssh/id_rsa debug1: Server accepts key: pkalg ssh-rsa blen 277 debug1: read PEM private key done: type RSA debug1: Authentication succeeded (publickey). for user jack it does not: jack@host1 ssh -v remhost debug1: Next authentication method: publickey debug1: Trying private key: /mnt/home/oper1/.ssh/identity debug1: Offering public key: /mnt/home/oper1/.ssh/id_rsa debug1: Authentications that can continue: publickey,password,keyboard-interactive I have looked at the permissions for all the keys and files, they look the same. Since I am using home directories mounted by NFS, the keys for both the remote host and the local host are in the same directory. This is how things look for jane: jane@host1$ ls -l $HOME/.ssh -rw-rw-r-- 1 jane operator 394 Jan 27 16:28 authorized_keys -rw------- 1 jane operator 1675 Jan 27 16:27 id_rsa -rw-r--r-- 1 jane operator 394 Jan 27 16:27 id_rsa.pub -rw-rw-r-- 1 jane operator 1205 Jan 27 16:46 known_hosts For user jack: jack@host1$ ls -l $HOME/.ssh -rw-rw-r-- 1 jack engineer 394 Jan 27 16:28 authorized_keys -rw------- 1 jack engineer 1675 Jan 27 16:27 id_rsa -rw-r--r-- 1 jack engineer 394 Jan 27 16:27 id_rsa.pub -rw-rw-r-- 1 jack engineer 1205 Jan 27 16:46 known_hosts As a last ditch effort, I copied the authorized_keys, id_rsa, and id_rsa.pub from jill to jack, and changed the username in authorized_keys and id_rsa.pub with vi. It still did not work. It seems there is something different between the two users but I cannot figure out what it is.

  Read the article

• How to change mount to grant user write permissions?

  - by nals

  I am on TomatoUSB, and using the feature to have a NAS. The only way I can write to the Samba share is if I force root: [global] interfaces = 127.0.0.1, 192.168.1.1/24 bind interfaces only = no workgroup = WORKGROUP netbios name = TOMATO security = share wins support = yes name resolve order = wins lmhosts hosts bcast guest account = nobody [Public] path = /mnt/sda2 read only = no public = yes only guest = yes guest ok = yes browseable = yes comment = Network share force user = root writeable = yes I dont really like the idea having to use root to allow write access to my share. I have a samba account created already named nobody to allow access to the share. However every time I try to write I get access denied error. fstab: /dev/sda2 /mnt/sda2 vfat defaults 0 0 Further more every time I try to chmod 777 /tmp/mnt/sda2 the permissions are not changed, and no error is produced. They stay 755. drwxr-xr-x 2 root root 4096 Jun 4 01:49 sda2 Basically; how can I give the user nobody write permissions to my mount? dev name: /dev/sda2 dev mount: /tmp/mnt/sda2

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >