Search Results

Search found 105 results on 5 pages for 'newegg'.

Page 4/5 | < Previous Page | 1 2 3 4 5  | Next Page >

• Hyper-V Server 2012 with Zambezi AMD FX-Series - Hardware assisted virtualization not present

  - by Vazgen

  I'm trying to set up VDI across Windows Server 2012 VMs running on Hyper-V 2012. The wizard's compatibility check for the Virtualization Host server failed with "Hardware-assisted virtualization is not present on the server". I'm running an FX-8120 CPU and have the ASUS M5A97 motherboard. I know I'm supposed to enable No-Execute (Hyper-V Hardware Considerations) but I cannot find that or any other synonyms of it in my motherboards UEFI BIOS (NX, XD, EVP, XN... nothing). I found this: PAE/NX/SSE2 Support Requirement Guide for Windows 8 which in short says "Windows 8 and Windows Server 2012 requires that systems must have processors that support NX, and NX must be turned on for important security safeguards to function effectively and avoid potential security vulnerabilities." this leads me to believe NX is on by default if I was able to get this far and install Hyper-V 2012 and Windows Server 2012.. Also I tried to disable AVX in cmd with "bcdedit /set xsavedisable 1". Did not resolve My processor is Zambezi FX-8120 and also supports RVI/SLAT/other synonym: processor: Newegg Processor FX-8120 support proof: AMD Processors with Rapid Virtualization Indexing Required to Run Hyper-V in Windows 8 What's going on here? I bought this CPU specifically after I had the same problems with an older AMD Athelon II and made sure to buy one with AMD-V and RVI. Thank you

  Read the article

• Do I need liquid cooling?

  - by Mrrvomun

  I'm building a computer mainly for gaming and developing games. It's going to be a three screen system with two GeForce GTX 460's and a quad-core i7. The newegg wattage calculator says I need around 900W. The case I intend to get is this one. Full specs if you need 'em are at the end of this post. I have no intentions to overclock the system at the moment, but this may change in the future. I've done a lot of research on the subject, and the answers I've found indicate that it takes a heck of a lot of power to require liquid cooling, and most non-overclocked systems don't need it. But I haven't seen a question about a system with two GPU's, so I ask you the following two questions: Assuming that the system is used for gaming for very extended periods of time (say 4-6 hours at a time, nonstop) with all three screens running at full 1080p, would the fans installed in the system suffice? Or would I need more fans and/or liquid cooling? If the system is used under the same circumstances as above, and is overclocked to a reasonable level, would the fans installed in the system suffice? Or would I need more fans and/or liquid cooling? Specs: Intel Core i7 16GB DDR3 Two nVIDIA GeForce GTX 460 3TB HDD Two DVD-RW writers Thermaltake 1050W power supply Case is linked above

  Read the article

• CPU and Motherboard clock speeds

  - by NZHammer

  I have been doing some reading about CPU clock speeds and how CPU clock speeds are calculated. After reading several articles, I have come to the understanding that your CPU clock speed is determined by: CPU clock speed = cpu multiplier x mobo clock speed A few questions came about after reading this which I cannot seem to find the answer to anywhere: If the CPU clock speed is dependent upon the mobo clock speed, then how is the clock speed of the CPU predetermined upon buying the CPU (i.e. written on the box without knowing what mobo is being used)? After installation, does the CPU adjust it's multiplier based upon the mobo clock speed to achieve advertised speeds? For example, if the CPU clocks speed is advertised at 2.4GHz and the mobo clock speed is 100MHz, will the multiplier be automatically set to 24x? Why does mobo clock speed seem to not be very important / talked about? For example, when I search on Newegg, mobo clock speed never seems to be listed. When I search enthusiast forums and overclocking forums, mobo clock speed is rarely mentioned. To me, it seems like the mobo clock speed would be pretty important. If I am understanding things correctly, a lower mobo clock speed means that you CPU must work harder to achieve advertised clock speeds. I guess that I should stop there with the questions for now, as I may be asking my questions based on incorrect assumptions. Thanks!

  Read the article

• LAN network (switch?)

  - by guywhoneedsahand

  I am working on setting up the network for a small LAN party (less than 16 people). Most of them do not have wireless cards in their rigs, so I need to set up some way for everyone to a) play LAN games and b) access the internet. The LAN party will probably take place in my basement, where I have enough space. However, the basement is not wired up with the router which is actually on the floor above. I make a cantenna a while back that can boost the wireless performance of my computer significantly. How can I use this to provide internet and LAN to guests? My hope was that I could use a switch like this http://www.newegg.com/Product/Product.aspx?Item=N82E16833181166 for the LAN - but how can I give people access to the internet? Is there such thing as a network extender / 16-port switch? Obviously, the internet performance doesn't need to be super stellar, because the games will be using LAN - so I am looking to provide some usable internet for web browsing, and very high speed LAN for games. Thanks!

  Read the article

• Picking a linux compatible motherboard

  - by Chris

  Last time I bought a new computer (I build them myself) I got a motherboard that had really poor linux support for a long time. Specifically the audio. I had to wait months before the kernel supported the on board audio chipset. That is exactly the situation I'm trying to avoid this time around. I have some specific questions about "server motherboards" actually. I looked at a few models of server motherboards by intel, and some random models on newegg. I wasn't able to see much of a difference from regular desktop motherboard other than most had two sockets, and support for much more ram. These boards seem more popular with Linux users. Why? AMD and Intel both have server CPUs as well. Some question, what's the difference? To make this question more concrete, I was looking at this this motherboard. The main questions about it that I can't answer are: Can I get a motherboard without on board raid and audio? I wanted to get a hardware raid controller and a PCI audio card. I thought a server motherboard would be cheaper and not have these "extras", since who wants an audio card on a server? Where can I found out about Linux support for the components on this board? "Intel ICH10R", "Realtek ALC889", "Marvell 88E8056" I'm buying this computer to work as a Linux desktop for a lot of compiling, coding and audio/video work, but I don't want to rule out the possibility of installing windows and playing some games at one point. (even if the last game I got has been sitting in its box unopened for almost a year). Is it a good idea to buy a "server motherboard" and play games on it, or are desktop boards better value for this? The ultimate solution for me would be a motherboard that had GPL divers for onboard LAN, a single CPU socket, lots of PCI express and PCI. USB 3.0, and no fancy hard disk controllers since I'll be getting a separate one.

  Read the article

• What LTO 4 drive to buy

  - by pplrppl

  Evan Anderson mentioned in another solution you could buy a LTO-4 (autoloader, 1 tape / day) - $4,566.00 (the discussion included total cost of tapes for a specific rotation.) but I don't know specifics on what he or you would recommend for the actual drive and if necessary controller. Show me a newegg URL or CDW, Dell, or HP, or whatever your favorite vendor would be for your solution if you don't mind looking it up or just give me a brand and a model number and I'll be glad to do the leg work myself. I currently have on have on hand an external LTO 3 drive that uses LVD SCSI interface (and thus have a controller card that has an external LVD SCSI connector). If that card isn't sufficient to interface to a LTO 4 drive let me know. http://www.fujifilmusa.com/shared/bin/LTO_Overview.pdf shows minimum tape speeds for LTO4 and other LTO formats. It looks like the IBM LTO4 actually has a lower minimum speed than the IBM LTO3. Either way my average server is too slow to feed LTO3/4 without shoeshining so I'm looking for a drive with a low minimum write speed. If you trust the PDF from 2008 that makes my choices IBM LTO 4 full height IBM LTO 4 half height HP LTO 4 half height but presumably there are other options out there that weren't mentioned in the fuji PDF. Again I'm looking for a specific recommendation on a drive to buy (and the controller if needed).

  Read the article

• Chipset fan on the frtiz - compressed air hasn't fixed anything - is there anything I can do?

  - by Anthony

  Yesterday, my computer started to make an annoying whining noise. Knowing that this is likely a fan issue, I opened the case and proceeded to determine which fan was causing the issue. I got some compressed air and tried cleaning out the dust around it (and the rest of the computer while I was at it). This hasn't seemed to fix the issue. Now, if it were just any fan, I would probably just replace the fan - they're relatively cheap after all. However, this is a special fan. Aside: For what its worth, I feel bad that the graphics card blocks part of the fan, but it is the only slot the graphics card fits, so I had no choice. After pulling out my motherboard user guide, it looks like this is a fan placed directly on top of the chipset. To be perfectly honest, I have no clue what the purpose of the chipset is - but it sounds important. After some quick research, I see that it is responsible for providing the bridge between my CPU, RAM and graphics, among other things. Just a quick search at Newegg tells me that chipset fans can be purchased at pretty reasonable prices (< 20 dollars). Is it practical to replace this fan? It is an old computer as computers go and I wouldn't be terribly upset to upgrade the motherboard and processor, so perhaps this is a sign. Hardware Specs: Motherboard: Asus A8N-E Chipset: NVIDIA nForce4 Ultra

  Read the article

• Will Intel be releasing anymore 6-core processors soon?

  - by jasondavis

  I am about to start buying parts every week for as long as it takes me to build the best PC I can build. I am looking at the Intel i7-920 processor right now because it is about 250$ and it is a quad-core processor based on the x58 chipset I believe. From what I have read so far, intel is coming out with some 6-core processors soon that will also use the x58 chipset and will allow me to use the same motherboard and memory/ram to upgrade to a 6-core. This sounds really good to me right now. I just read that the new 6-core processor. The Core i7-980X (extreme edition) was just released which is the first 6-core processor but it is supposed to be around $1,000 so I will probably just get the i7-920 for now and then upgrade to the 6-core version when the price goes down. The motherboard I am looking at getting the GIGABYTE GA-X58A-UD5 which is around $280 at newegg.com So that is my basic plan SO far. I have not purchased any parts yet. I am just wanting to ask if this sounds like a good idea or if I should wait longer if I am wanting to eventually have a 6-core processor. Does anyone know if Intel is planning on releasing any other 6-core processor in addition to the Core i7-980X in the near future? I just want to make sure I am buying the best setup for my money if I am going all out on it, thanks for any tips/advice.

  Read the article

• Does a mini PCIe SSD fit into a Acer Aspire One?

  - by Narcolapser

  Question: What, if any, mini PCIe SSDs fit into the mini PCIe slot of the Acer Aspire one AOD250? Info: I have an Aspire One and I've been considering loading it with an SSD. The mini PCIe drives fascinate me and so I want to try that approach. Also they tend to be cheaper and not much slower. (at least not on Read time which matters more for a netbook) But I've heard that some times computers don't support certain mini PCIe cards. And I was wondering if anyone knew about the Aspire One? I tried asking Acer tech support, but they didn't know jack and spent the whole time informing that I would have to support my Ubuntu install on my own, which I was. Anyway. Rant Aside, I'm looking at this drive: http://www.newegg.com/Product/Product.aspx?Item=N82E16820183252 It states it is exclusively for the Eee PC. now does that mean It was designed for the Eee PC but will work in my netbook. or is something going to go wrong? (like right now my concern is it physically not fitting.) Any information would be appreciated. o7

  Read the article

• picking a linux compatable motherboard

  - by Chris

  Last time I bought a new computer (I build them myself) I got a motherboard that had really poor linux support for a long time. Specifically the audio. I had to wait months before the kernel supported the on board audio chipset. That is exactly the situation I'm trying to avoid this time around. I have some specific questions about "server motherboards" actually. I looked at a few models of server motherboards by intel, and some random models on newegg. I wasn't able to see much of a difference from regular desktop motherboard other than most had two sockets, and support for much more ram. These boards seem more popular with Linux users. Why? AMD and Intel both have server CPUs as well. Some question, what's the difference? To make this question more concrete, I was looking at this this motherboard. The main questions about it that I can't answer are: Can I get a motherboard without on board raid and audio? I wanted to get a hardware raid controller and a PCI audio card. I thought a server motherboard would be cheaper and not have these "extras", since who wants an audio card on a server? Where can I found out about Linux support for the components on this board? "Intel ICH10R", "Realtek ALC889", "Marvell 88E8056" I'm buying this computer to work as a Linux desktop for a lot of compiling, coding and audio/video work, but I don't want to rule out the possibility of installing windows and playing some games at one point. (even if the last game I got has been sitting in its box unopened for almost a year). Is it a good idea to buy a "server motherboard" and play games on it, or are desktop boards better value for this? The ultimate solution for me would be a motherboard that had GPL divers for onboard LAN, a single CPU socket, lots of PCI express and PCI. USB 3.0, and no fancy hard disk controllers since I'll be getting a separate one.

  Read the article

• ssd firmware, linux: updating large batch of drives

  - by wryfi

  I was recently hit with a fatal firmware bug that affected dozens of Crucial SSDs deployed in my datacenter. Many of the affected machines use LSI or other proprietary SAS controllers, which Crucial's bootable ISO does not recognize. None of the affected machines has a Windows license. The story is roughly similar for other SSD mfrs, including Samsung and Intel. To resolve this issue, I was forced to stop each machine, remove the affected SSD, remove the SSD from its hotswap caddy, install it temporarily into my ThinkPad, flash the firmware, reverse, rinse, repeat. It took the better part of a day to get through all the affected devices. I am looking for hardware, software, and/or purchasing strategies to ease this pain, as SSD firmware bugs seem inevitable, and our SSD footprint is growing. My first thought is to get a laptop with eSATA and one of these cables (http://www.newegg.com/Product/Product.aspx?Item=N82E16812311004). That should at least make it so I don't have to remove the drives from their caddies. Surely others have run into this. Any novel solutions?

  Read the article

• Building vs buying a server for an academic lab [closed]

  - by Roy

  I'm looking for advice on the classic build vs buy question. We need a new linux server to run Matlab computation on in our lab (academic). Matlab parallel computing toolbox licence allows up to 12 local workers so we are aiming at a 12 core server with 4GB memory per core (total of 48gb). The system will have an SSD for the OS and a raid-5 (4x2tb) for data. I looked around and found a (relatively) cheap vendor, Silicon Mechanics, that offers a system to our liking (specs below) for $6732. However, buying the components from newegg cost only $4464! The difference is $2268 which is 50% of the base cost. If buying from a company can be thought of as a sort of insurance, basically my premiums are of 50% of the base cost which to me sounds like a lot. Of course any downtime is bad, but the work is not "mission critical", i.e. if it takes a few days to fix it when it breaks its no the end of the world. If it takes weeks to months then its a problem. If it breaks 2-3 times in 3 years, not too bad. If it breaks every month not good. In term of build experience, I set up a linux cluster in grad school (from existing computers) and I build my home pcs but I never built a server before. The server components I'm thinking about: 1 x SUPERMICRO SYS-7046T-6F 4U Tower Server Barebone Dual LGA 1366 Intel 5520 DDR3 1333/1066/800 ($1,050) 12 x Kingston 4GB 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) ECC Unbuffered Server Memory ($420) 2 x Intel Xeon E5645 Westmere-EP 2.4GHz LGA 1366 80W Six-Core ($1,116) 4 x Seagate Constellation ES 2TB 7200 RPM SATA 6.0Gb/s 3.5" ($1,040) 1 x SAMSUNG Internal DVD Writer Black SATA ($20) 1 x Intel 520 Series 2.5" 180GB SATA III MLC SSD $300 1 x LSI LSI00281 PCI-Express 2.0 x8 MD2 Low profile SATA / SAS MegaRAID SAS 9260CV-4i Controller Card, $695

  Read the article

• Expresscard Not Detected in PCI-E Adapter

  - by maxpower47

  I'm trying to put an expresscard TV tuner (Avermedia HC82) into my HTPC using this expresscard to PCI-E adapter. I've verified that the tuner works fine in my laptop. The motherboard is a Biostar TF7050-M2. When I install it and turn it on, the light on the back of the adapter comes on fine (there are two indicator lights on the back to show if it is using PCI-E or USB communication, USB communication goes through a USB cable connected between the card and a header on the motherboard) showing that it is working in PCI-E mode. However, the device is never detected in Windows 7 Professional x64. The auto detect never happens, it doesn't show up in the device manager, and I can have it rescan for new hardware and nothing is found. I tested the whole setup (tuner + adapter) in another PC (also using Win 7 Pro x64) and it worked fine. I also tried: Plugging the adapter in to the PCI-E x16 slot on the motherboard (I verified first that the x16 slot worked by installing a video card in it) Booting into safe mode and rescanning Updating the chipset drivers Installing the tuner drivers first Using a different USB cable, plugged in to one of the known good ports on the back of the board Trying it without the USB cable plugged in Removing the other PCI cards that were installed on the board Looking through the BIOS for any setting that might be disabling it somehow to no avail. I'm at a loss for what else to try. I really don't want to RMA it (the shipping back to newegg will be almost as much as it cost to buy in the first place. Any ideas?

  Read the article

• Where do vendors publish internal transfer rates of HDDs?

  - by red888

  So I've started to dig into storage fundamentals and found that in order to calculate the IOPS of a HDD you need to know the internal transfer rate of the drive (time it takes data to move from the platters to internal disk's cache). I went on newegg and even a few vendor sites and could not find this info published for any HDDs. Is it sometimes called something else? Take this link to a seagate HDD for instance. Nowhere do I see "internal transfer rate", but I do see something called "Sustained Data Rate OD"- is that the same thing? Just so you know where I'm getting this info (Book: "Information Storage and Management Storing, Managing..."): Consider an example with the following specifications provided for a disk: The average seek time is 5 ms in a random I/O environment; therefore, T = 5 ms. Disk rotation speed of 15,000 revolutions per minute or 250 revolutions per second — from which rotational latency (L) can be determined, which is one-half of the time taken for a full rotation or L = (0.5/250 rps expressed in ms). 40 MB/s internal data transfer rate, from which the internal transfer time (X) is derived based on the block size of the I/O — for example, an I/O with a block size of 32 KB; therefore X = 32 KB/40 MB. Consequently, the time taken by the I/O controller to serve an I/O of block size 32 KB is (TS) = 5 ms + (0.5/250) + 32 KB/40 MB = 7.8 ms. Therefore, the maximum number of I/Os serviced per second or IOPS is (1/TS) = 1/(7.8 × 10^-3) = 128 IOPS.

  Read the article

• Computer Won't Boot Properly, unless in safe mode?

  - by Mr_CryptoPrime

  I bought a computer today and booted it up, but when I did I only got a blank screen. I checked to make sure it wasn't the monitor by connecting it to my old computer...it worked. I then tried connecting my monitor to both DVI ports and found that the bottom one did work. However, now it just boots up and says "loading windows" and then when the login screen is suppose to come up the screen just goes blank and monitor says "no input, check cord" (or something like that). I tried reinstalling windows and then I was able to log on normally. I used the CD's and reinstalled all the drivers, then rebooted...now I am stuck right back where I started. I tried taking out the RAM and inserting into different slots, that didn't fix anything. I was able to boot up into windows using safe-mode. I suspected that my ATI Radeon 6950 was the issue and downloaded the drivers, but I can't install them on safe-mode. Someone said to install C++ distr. and I tried doing that to fix driver installation problem of "failed to load detection driver" but it wouldn't let me do that either. Please someone help me, I don't want to have to deal with the evil redtape of sending it back to get a replacement! My computer: -Content--text-_-"http://www.newegg.com/Product/Product.aspx?Item=N82E16883229236&nm_mc=TEMC-RMA-Approvel&cm_mmc=TEMC-RMA-Approvel--Content--text-_- Driver detection problem: http://www.hardwareheaven.com/hardwareheaven-tools-discussion/174912-failed-load-detection-driver-installation-error.html Driver download page: http://sites.amd.com/us/game/downloads/Pages/radeon_win7-64.aspx#1 I am using windows 7. Thanks again.

  Read the article

• DVI splitter not working as expected/confusion between DVI-D and -I

  - by Freakishly

  Hey guys, thanks for looking. I have an ATI FirePro™ V3700 in my desktop machine, and I have been running a dual-monitor setup quite effortlessly, thanks to the two DVI ports on the card. I came upon a third monitor, and wanted to extend my desktop to 3 screens, so I purchased a DVI splitter from Amazon. Now, I can only duplicate the second monitor onto the third, not extend it. I've tried all possible combinations of input to no avail. Here's the setup: The ATI FirePro™ V3700 has two Dual-Link DVI-I outputs The splitter splits a single Dual-Link DVI-I port into two Dual-Link DVI-I outputs Two of the monitors are NEC E222W, and the third monitor is a Dell 2001FP. Each monitor has one D-Sub and one Dual-Link DVI-D input. Cables going from the video card to the monitors are two Dual-Link DVI-D to the NECs and one Single-Link DVI-D to the Dell. Is the problem likely with the DVI-D/DVI-I mismatch? Or is it with the cable on the Dell that is only a Single-Link? The cables are easily replaceable, the monitors not so much. Thanks for your time, I really appreciate it. http://www.amd.com/us/products/workstation/graphics/ati-firepro-3d/v3700/Pages/v3700-specs.aspx http://www.amazon.com/Cables-Unlimited-DVI-D-Splitter-PCM-2260/product-reviews/B000H09RFM/ref=dp_top_cm_cr_acr_txt?ie=UTF8&showViewpoints=1 www dot newegg dot com/Product/Product.aspx?Item=N82E16824002495 accessories dot us dot dell dot com/sna/PopupProductDetail.aspx?cs=19&l=en&c=us&sku=320-1578 Apologies for the fudged links, I'm new here and they won't let me post more than two :P

  Read the article

• Computer randomly shuts itself off

  - by Decency

  I have not been able to determine a pattern for why this happens, despite my best efforts. I've attempted to run it on full power with Prime95 and this doesn't trigger a restart. Generally the restarts occur while I'm playing games, watching videos, or even just having multiple tabs open in a browser. However, I often play processor intense games for hours without any restarts occurring, and sometimes they'll happen 3-4 times in an hour during less intense activity, so I don't think that is the problem. I imagine it has something to do with overheating or power consumption so I've been monitoring CPU temperature and cleaning with compressed air, but the problem keeps happening. I don't know how to track power consumption, and assume that this is the problem. Whenever this occurs, the sound gets stuck in a short loop of whatever was playing at the time, though restarts also occur when nothing is playing. Here is a screenshot of temperatures: and under load: Here's the parts list: http://secure.newegg.com/WishList/PublicWishDetail.aspx?WishListNumber=10546754 As shown in the list, the case includes a 585W Power Supply, which I've been told should be plenty. I built the computer myself with a friend's guidance but it's very possible I did something wrong. Right now I'm looking into ensuring that I have the latest drivers for all components. Any help would be appreciated- thanks.

  Read the article

• Network switches for LAN party

  - by guywhoneedsahand

  I am working on setting up the network for a small LAN party (less than 16 people). Most of them do not have wireless cards in their rigs, so I need to set up some way for everyone to a) play LAN games and b) access the internet. The LAN party will probably take place in my basement, where I have enough space. However, the basement is not wired up with the router which is actually on the floor above. I make a cantenna a while back that can boost the wireless performance of my computer significantly. How can I use this to provide internet and LAN to guests? My hope was that I could use a switch like this http://www.newegg.com/Product/Product.aspx?Item=N82E16833181166 for the LAN - but how can I give people access to the internet? Is there such thing as a network extender / 16-port switch? Obviously, the internet performance doesn't need to be super stellar, because the games will be using LAN - so I am looking to provide some usable internet for web browsing, and very high speed LAN for games. Thanks!

  Read the article

• Computer Won't Boot Properly, unless in safe mode?

  - by Mr_CryptoPrime

  I bought a computer today and booted it up, but when I did I only got a blank screen. I checked to make sure it wasn't the monitor by connecting it to my old computer...it worked. I then tried connecting my monitor to both DVI ports and found that the bottom one did work. However, now it just boots up and says "loading windows" and then when the login screen is suppose to come up the screen just goes blank and monitor says "no input, check cord" (or something like that). I tried reinstalling windows and then I was able to log on normally. I used the CD's and reinstalled all the drivers, then rebooted...now I am stuck right back where I started. I tried taking out the RAM and inserting into different slots, that didn't fix anything. I was able to boot up into windows using safe-mode. I suspected that my ATI Radeon 6950 was the issue and downloaded the drivers, but I can't install them on safe-mode. Someone said to install C++ distr. and I tried doing that to fix driver installation problem of "failed to load detection driver" but it wouldn't let me do that either. Please someone help me, I don't want to have to deal with the evil redtape of sending it back to get a replacement! My computer: -Content--text-_-"http://www.newegg.com/Product/Product.aspx?Item=N82E16883229236&nm_mc=TEMC-RMA-Approvel&cm_mmc=TEMC-RMA-Approvel--Content--text-_- Driver detection problem: http://www.hardwareheaven.com/hardwareheaven-tools-discussion/174912-failed-load-detection-driver-installation-error.html Driver download page: http://sites.amd.com/us/game/downloads/Pages/radeon_win7-64.aspx#1 I am using windows 7. Thanks again.

  Read the article

• Computer turns on and off very quickly, then nothing, then works?

  - by hellohellosharp

  The strange nature of this problem is what is stumping me. I built my computer about 7 months ago using all new parts off of Newegg (not a kit or anything). One day, I wake up and turn on my computer. I press the power button and it turns on, but then back off after half a second. I press the power button again, this time nothing. I continue pressing the power button while at the same time turning the power supply on and off (to try and reset things). The power button still does nothing. But then, after about 5 minutes, WALLAH, it works just fine like nothing was ever wrong. It goes for an entire week working just fine. Then, one morning, the entire process starts again. I press the power button and it comes on and then right back off. I press the power button several times and nothing happens, and then it works again after a couple minutes of trying. What is going on with my computer?

  Read the article

• Backing up my Windows Home Server to the Cloud&hellip;

  - by eddraper

  Ok, here’s my scenario: Windows Home Server with a little over 3TB of storage.  This includes many years of our home network’s PC backups, music, videos, etcetera. I’d like to get a backup off-site, and the existing APIs and apps such as CloudBerry Labs WHS Backup service are making it easy.  Now, all it’s down to is vendor and the cost of the actual storage.   So,  I thought I’d take a lazy Saturday morning and do some research on this and get the ball rolling.  What I discovered stunned me…   First off, the pricing for just about everything was loaded with complexity.  I learned that it wasn’t just about storage… it was about network usage, requests, sites, replication, and on and on. I really don’t see this as rocket science.  I have a disk image.  I want to put it in the cloud.  I’m not going to be be using it but once daily for incremental backups.  Sounds like a common scenario.  Yes, if “things get real” and my server goes down, I will need to bring down a lot of data and utilize a fair amount of vendor infrastructure.  However, this may never happen.  Offsite storage is an insurance policy.   The complexity of the cost structures, perhaps by design, create an environment where it’s incredibly hard to model bottom line costs and compare vendor all-up pricing.  As it is a “lazy Saturday morning,” I’m not in the mood for such antics and I decide to shirk the endeavor entirely.  Thus, I decided to simply fire up calc.exe and do some a simple arithmetic model based on price per GB.  I shuddered at the results.  Certainly something was wrong… did I misplace a decimal point?  Then I discovered CloudBerry’s own calculator.   Nope, I hadn’t misplaced those decimals after all.  Check it out (pricing based on 3174 GB):   Amazon S3 $398.00 per month $4761 per year Azure $396.75 per month $4761 per year Google $380.88 per month $4570.56 per year   Conclusion: Rampant crack smoking at vendors.  Seriously.  Out. Of. Their. Minds. Now, to Amazon’s credit, vision, and outright common sense, they had one offering which directly addresses my scenario:   Amazon Glacier $31.74 per month $380.88 per year   hmmm… It’s on the table.  Let’s see what it would cost to just buy some drives, an enclosure and cart them over to a friend’s house.   2 x 2TB Drives from NewEgg.com $199.99   Enclosure $39.99     $239.98   Carting data to back and forth to friend’s within walking distance pain   Leave drive unplugged at friend’s $0 for electricity   Possible data loss No way I can come and go every day.     I think I’ll think on this a bit more…

  Read the article

• Will this RAID5 setup work (3TB Seagate Barracudas + Adaptec RAID 6405)?

  - by Slayer537

  As the title states, will this RAID combo work, and if not what needs to be changed? Overall opinions would be most helpful. I currently run a small file server of about 5TB or so. I keep outgrowing my needs and need to build a RAID setup that will allow me to expand as needed. I am new to RAID setups, especially one of the scale I have currently planned out, but I have being doing some research for the past couple of weeks and have come up with a build. Ideally, I'd have the setup completely built, but I'd like to keep the total cost around $1k and can't afford to go above $1.5k, so unfortunately that's not an option. 2 of my current drives are WD Caviar Blacks 2TB; however, I have recently learned that due to the lack of TLER those drives are awful for any RAID setup other than 0 or 1. That being said, my third drive is a Seagate Barracuda 3TB (ST300DM001) and I have found a RAID controller that states it supports it, so I'd like to use this same type of drive, if possible. Have any of you had any experience using this drive or a similar one in a RAID5 configuration? The manufacturer states that it supports it, but knowing that it is not an enterprise drive, I am slightly concerned that it could drop out of the array. I would just go with enterprise drives, but those are about double in cost... Parts list: Storage rack: http://www.ebay.com/itm/SGI-3U-Media-Storage-Server-16-Hard-Drive-Bay-SATA-SAS-Expander-Omnistor-SE3016-/140735776937?pt=LH_DefaultDomain_0&hash=item20c48188a9 3 more HDs (for now..): http://www.amazon.com/Seagate-Barracuda-3-5-Inch-Internal-ST3000DM001/dp/B005T3GRLY/ref=dp_return_2?ie=UTF8&n=172282&s=electronics Adaptec RAID 6405: http://www.newegg.com/Product/Product.aspx?Item=N82E16816103224 here's a link to the compatibility sheet if that helps: http://download.adaptec.com/pdfs/compatibility_report/arc-sas_cr_03-27-12_series6.pdf SAS expander cable: http://www.pc-pitstop.com/sas_cables_adapters/8887-2M.asp My plan is to install the RAID card in my computer and then route the SAS cable to the rack. Setup a RAID5 on 3 drives, transfer my data over from my other drive, and then add that drive to the array. Eventually, I'd like to get a 2U unit and run the file server on that and move the RAID card over to there, but that will have to happen later on. Side note: The computer the card would be going into will be running Windows 7 Pro with 24GB of DDR3-1600 and an i7-930.

  Read the article

• Hard freeze on new computer

  - by mphair

  OCZ Gold 3x2GB 240-Pin DDR3 SDRAM PC312800 Palit NE5T240SFHD01 GeForce GT240 1GB 128-bit GDDR5 ASUS P7P55D-E LGA 1156 P55 SATA 6Gb/s USB 3.0 ATX Intel Motherboard Intel Core i7-860 Lynnfield 2.8GHz 8MB L3 Cache LGA 1156 95W Quad-Core Processor SAMSUNG 22X Optical drive (DVD+-R/RW) CORSAIR CMPSU-620HX 620W ATX12V V2.2 Windows 7 Ultimate x64 Brand new system (got it from newegg two days ago) and it booted up and installed windows and ran for a day just fine. Yesterday, I boot it up in the afternoon and run various games at full graphics for most of the day. I turn on WoW and play for a few hours and it hard stalls. No numlock switching, no mouse feedback but nothing going wrong on the screen. No BSOD. I wait a bit to see if the stall is just a temporary one, but then force shutdown the computer. Upon reboot, everything seems fine, windows sees that it didn't shut down properly but I go into normal boot and restart WoW. I'm able to load it up and start running around when it freezes again. This time when I restart, it doesn't even get to BIOS. It starts (power goes on) and it just hangs with no output to the monitors. I shut it off and went to bed. This morning, I turned it on and went into BIOS setup. I'm not terribly experienced with messing with BIOS settings but I checked over them the best I could. Everything seems fine so I boot into windows and browse the internet for a bit looking for a solution, hard freeze within 10 minutes. I restart and go into BIOS and check the CPU temperature, 40c. I'm kinda stumped here. Some people say it might be a memory issue, but why would it take so long for it to come up? Could it have been slowly accessing one memory stick at a time and then it just got to a bad one and that's what is causing it to fail? It seems odd that I don't get a BSOD from a hardware failure. Having the screen just halt with no input or output change seems like a software thing to me. Any thoughts?

  Read the article

• Windows 7 Home hangs at "Welcome" screen

  - by White Phoenix

  I'm asking on behalf of a friend who's currently having problems with his machine. Windows 7 Home 32-bit. He's too far away for me to help by going over to his house - I'm helping him over the Internet. This is his current machine: http://www.newegg.com/Product/Product.aspx?Item=N82E16883227134 The only two changes he made to that machine is to swap out the gfx card for a EVGA GTX 460 and the PSU for a Corsair TX650. Here's what happened: He was playing a computer game (fairly CPU/GPU intensive) and had some music going in the background in foobar while playing. Suddenly, he notices the music stopped playing, so he switches to foobar to try to close it, but it freezes up (window won't respond). So he figures it's just foobar having a bad day and force quits that program. Suddenly, his game won't respond, so he force quits that, then the entire computer just went to crap at that point, so he hits the restart button on his machine. Computer POSTS fine, but now he gets stuck at the Windows "welcome" screen (his account is set to auto-login). HD activity light is solid yellow but he doesn't hear HDD activity. He tried booting into Safe Mode - gets stuck at the "welcome screen". Tried a STartup Repair within Windows 7, it found a few problems, but still gets stuck at welcome. I advised him to boot off the DVD - sfc /scannow found nothing (couldn't use the regular /scannow option; says there's a repair pending, had to use use offbootdir/offwindir command switches). Ran startup repair 3 times - found nothing. My friend runs virus/malware scans on a regular basis, so he's fairly sure it's not that either. Right now I'm having my friend run chkdsk /R on the computer while in this Startup Recovery mode - so far it's caught a few bad sectors. However at this point I'm kinda wondering which way to go if chkdsk doesn't fix it. Quick Google search said someone had success by booting Windows with bootlogging on - some others have success with running the aforemented chkdsk, etc. The fact that Windows cannot even boot into Safe Mode concerns me. While we're waiting for chkdsk /R to finish, are there any other options I can give my friend short of reinstalling Windows 7? He has his data on a separate partition so that's not a major problem (though it'll be an annoyance for him). I suspect his hard drive may be having some issues, but my main concern is getting him back up and running before we start diagnosing the hard drive (I may have him run some sort of SMART test utility later).

  Read the article

• Educate me - should I buy these prebuilt NAS (which is better) or make my own?

  - by user29336

  I'm trying to learn as much as possible, and I think I've learned quite a bit so bear with me here under my confusion. I found a coupe NAS setups. I'm not sure if one is better than the other, other than the price being higher on some, and some coming with drives VS not. Let me list my setup so you can get an idea of what I want to provide: Macbook Pro Macbook Mini for Media streaming (so far) Windows 7 Gaming Computer Xbox 360 I'd like to provide a storage system for all these devices so they can access files very easily, I'd also like any of these devices to be able to stream media from this storage system. I'd like this storage system to be hassle free in terms of my confidence in the data integrity. If a drive fails, I want to know that I can replace the drive and all my files will still exist. I'd like to access this storage system OUTSIDE of my LAN. If I'm out on a job for work I'd like to go in, or be able to have people DL some files. This brings me to a question, is this what iSCSI is? I'd like this data system to be able to download torrents. I want to mount any drive on this storage system onto my OSX laptop as if it were a local drive attached. (Is this with iSCSI is?) I'd like this system to have a GOOD web based GUI. I don't want to install software to use it. I believe those are the most of my requirements. If I'm missing something that I have no knowledge about, can someone educate me? Here are the systems I found: $729ish on Newegg Lacie 5Big Network 2 (comes with 5TB of space. iSCSI / mac compatible, torrents, nice ui, + others?) Is this overpriced for what it provides? It almost seems like a great deal to me because of the 5TB of space it comes with vs the other NAS systems that don't come with storage but cost $600-700. Should I get a different NAS system? Netgear? Others? Do they have same features? Better? Is it better to buy your own disks? What about making my own? I'm tech savy all around. It seems cheaper to buy a premade one especially with the support/warranty it provides...

  Read the article

< Previous Page | 1 2 3 4 5  | Next Page >