Search Results

Search found 111 results on 5 pages for 'pppoe'.

Page 4/5 | < Previous Page | 1 2 3 4 5  | Next Page >

• When connected through a router, a new gateway appears, and I lose my internet connection.

  - by idan315

  I have two computers connected to a router, connected to my ADSL modem by PPPoE. One of those computrs use Windows XP, the other uses Windows 7. The computer using Windows 7 keeps getting limited or no connectivity, and I can't use it to connect to the internet. Connecting the computer to the modem without the router 'in the way' worked, and I was able to use the internet - which led me to believe that the problem is with my router. However, I have changed my router, and the problem persists. (Just to be clear: the computer using Windows XP can connect to the internet without any problem). This entire question is about the PC using Windows 7. The only symptom of this problem is that when I see my network devices, in addition to my router (which appears as "Network 4", or something of the sort), I also see an "Unidentified Network". When using ipconfig to check the problem, I see a second gateway, with the IP 0.0.0.0, in addition to the IP of my router.

  Read the article

• IPv6 6to4 on Windows Server

  - by Graham Wager

  I'm looking for a relatively simple guide to setting up IPv6 properly on a home network. This network currently has a server (Windows Server 2008R2) running RRAS that establishes connectivity to the internet using a demand-dial PPPoE connection and handles the NAT. It also hosts a DNS server and DHCP. My ISP does not support IPv6, but I have a static IPv4 address. I've read about 6to4 and signed up at tunnelbroker.net, but quickly felt out of my depth. How do I configure my network to use it, and how I should configure my DHCP server with regards to IPv6 addresses?

  Read the article

• Dual-WAN router

  - by aix

  I am looking for a router that would fit the following requirements: Two WAN interfaces: the primary is PPPoE, the secondary will link to a GigE port on another router (a 100Mbps link will suffice); Two (ideally four) GigE LAN ports; No requirement for a firewall; No requirement for Wi-Fi; Inexpensive. The plan for the two WAN interfaces is as follows. All outbound traffic will go to the primary, with exceptions based on destination IP/subnet or possibly on src+dest IPs/subnets. Such exceptions should be routed to the secondary. It would be very nice if, should the primary go down, the secondary would automatically take over for all outbound traffic. I am reasonably sure that I can put something together based on dd-wrt. However, I'd like to hear from you what alternatives are out there (especially something easier to set up for my use case, even if it means paying more for the hardware.)

  Read the article

• Virtual firewall to protect hypervisor

  - by manutenfruits

  I am running an Ubuntu Server 12.10 as a single host connected to a NATed router connected using PPPoE to a optical fiber modem. This server is meant to be accessed from the Internet, but also to be used from the LAN as a SVN, MySQL and what not... The issue is that the router is not customizable enough to serve, so I was thinking about creating a virtual pfSense firewall using KVM inside of the server itself, removing the need of the router. Is this possible? Can the host ignore and block all traffic coming to itself, but not for the firewall? I am aware this is not the most desirable environment, I accept suggestions based on budget!

  Read the article

• Is there a way to submit a batch of commands to a Cisco router and have them execute from the router?

  - by atroon

  I need to change the configuration of a remote (6 hours' drive) client's Cisco 871 (IOS 12.4.15T) from my location because of some new internet service at his location. To be more precise, I need to change the default route, ip address of the outside interface (Fa4) and disable the PPPoE setup there. Unfortunately, doing any of this will (obviously) break the connection to the router. I do not have an out-of-band management modem set up (I know, I know). Is there any way to enter the commands I need to have run and have them execute one after the other, from a file on flash:? I have never tried anything like that before. Essentially a DOS-style batch file is exactly what I need. Nothing like it seems to be out there except using kron to execute CLI commands, but that is specified here as only taking EXEC commands, not configuration ones. Is there hope, or do I travel?

  Read the article

• Removing (Presumably) Extraneous Network Adapters from Device Manager (eg WAN Miniport)

  - by Synetech inc.

  Can anyone shed some light on the default items in the Network Adapters branch of the Windows Device Manager? In addition to the network card, there are always a bunch of other things that I cannot find any useful information on such as RAS Asynch Adapter and all the WAN Miniports (IKEv2, IP(v6), L2TP, Network Monitor, PPPOE, PPTP, SSTP). I would like to trim it down and uninstall whatever possible but cannot find out exactly what these items are responsible for (and therefore whether or not they are needed on my system). Most of the pages found with Google are either people trying to fix an error with such an item or someone asking what it is and being given an unhelpful, pat response like “just leave them alone” or “they’re necessary”. I highly doubt that is the case and I’m certain that at least some items can be removed because even if they become necessary in the future they can be added again (for example installing Network Monitor or Protowall reinstalls the miniport drivers anyway).

  Read the article

• ASA 5505 Vlan question

  - by Wayne

  I am setting up a cisco asa 5505 with the base license. I can communicate from inside-outside, outside-inside, inside-home, which is my desired traffic security. I can get http, ssh, and other access from inside-home, but I can't ping from inside-home (192.168.110.0 host to 192.168.7.1 or 192.168.7.0 host). Can someone explain. My config is listed below interface Vlan1<br> nameif inside<br> security-level 100<br> ip address 192.168.110.254 255.255.255.0 <br> !<br> interface Vlan2<br> nameif outside<br> security-level 0<br> pppoe client vpdn group birdie<br> ip address removedIP 255.255.255.255 pppoe <br> !<br> interface Vlan3<br> no forward interface Vlan1<br> nameif home<br> security-level 50<br> ip address 192.168.7.1 255.255.255.0 <br> ! <br> interface Ethernet0/0<br> switchport access vlan 2<br> ! <br> interface Ethernet0/1<br> ! <br> interface Ethernet0/2<br> ! <br> interface Ethernet0/3<br> ! <br> interface Ethernet0/4<br> switchport access vlan 3<br> ! <br> interface Ethernet0/5<br> shutdown <br> ! <br> interface Ethernet0/6<br> shutdown <br> ! <br> interface Ethernet0/7<br> shutdown <br> ! <br> ftp mode passive<br> clock timezone EST -5<br> clock summer-time EDT recurring<br> access-list Outside-In extended permit icmp any any <br> access-list Outside-In extended permit tcp any any eq www <br> access-list Outside-In extended permit tcp any any eq https <br> access-list Outside-In extended permit tcp any any eq 5969 <br> access-list inside_nat0_outbound extended permit ip any 192.168.111.0 255.255.255.224 <br> access-list standardUser_splitTunnelAcl1 extended permit ip 192.168.111.0 255.255.255.0 any <br> access-list standardUser_splitTunnelAcl1 extended permit ip 192.168.110.0 255.255.255.0 <br>any access-list inside_in extended permit icmp any any <br> access-list inside_in extended permit ip any any <br> access-list home_in extended permit icmp any any <br> access-list home_in extended permit ip any any <br> pager lines 24<br> logging enable<br> logging asdm informational<br> mtu inside 1492<br> mtu outside 1492<br> mtu home 1500 <br> ip local pool vpnuser 192.168.111.5-192.168.111.20<br> icmp unreachable rate-limit 1 burst-size 1<br> asdm image disk0:/asdm-524.bin<br> no asdm history enable<br> arp timeout 14400<br> nat-control <br> global (outside) 1 interface<br> nat (inside) 0 access-list inside_nat0_outbound<br> nat (inside) 1 0.0.0.0 0.0.0.0<br> nat (home) 1 192.168.7.0 255.255.255.0<br> static (inside,outside) tcp interface https 192.168.110.6 https netmask 255.255.255.255 <br> static (inside,outside) tcp interface www 192.168.110.6 www netmask 255.255.255.255 <br> static (inside,outside) tcp interface 5969 192.168.110.12 5969 netmask 255.255.255.255 <br> static (inside,home) 192.168.110.0 192.168.110.0 netmask 255.255.255.0 <br> access-group inside_in in interface inside<br> access-group Outside-In in interface outside<br> access-group home_in in interface home<br> route outside 0.0.0.0 0.0.0.0 RemovedIP 1<br>

  Read the article

• Will disabling NAT on my wireless router cause a performance hit on my DSL router?

  - by user117313

  I have a Thomson TG508v2 router/modem and a brand new AirPort Extreme connected to it. At first, I set the AirPort Extreme to "share a public IP", which enables DHCP/NAT. Everything works great but I was having the Double NAT error. So I set the AirPort Extreme as bridge mode, which disables DHCP/NAT and let my crappy modem handle my internal network IPs. Will this cause any performance hit in my network? I'm worried because I'll outsource this job from AirPort Extreme (premium hardware) to the crappy modem. Before you suggest, I tried setting my modem as a bridge and configuring PPPoE on the AirPort Extreme, however it wouldn't connect to the internet, so I just dismissed leaving the modem as bridge.

  Read the article

• IPv6 6to4 on Windows Server

  - by Graham Wager

  I'm looking for a relatively simple guide to setting up an IPv6 tunnel properly. This network currently has a server (Windows Server 2008R2) running RRAS that establishes connectivity to the internet using a demand-dial PPPoE connection and handles the NAT. It also hosts a DNS server and DHCP. My ISP does not support IPv6, but I have a static IPv4 address. I've read about 6to4 and signed up at tunnelbroker.net, but quickly felt out of my depth. How do I configure my network to use it, and how I should configure my DHCP server with regards to IPv6 addresses?

  Read the article

• Windows VPN not authenticating from ADSL to Wireless link

  - by deanvz

  I have a normal windows VPN on a computer connecting to a 196.201.x.x/24 IP. If this VPN tries to connect from any address in the 41.x.x.x range it cant get there. The server is a normal windows 2008 server, running exchange with a PPPoE IP natted to a public IP on the public gateway of the wireless network as the server is on site and its connectivity is derived from Mikrotik RB's. The computer on the 41 range can traceroute and ping the server, but the VPN does not authenticate. When on the network or any other, the VPN works fine. Is there something that could be configured on the VPN client? All firewall settings of a standard ADSL router have been checked and found to block only ICMP's. Is this a VPN configuration problem or a network issue?

  Read the article

• How to access an node of an LAN via WAN?

  - by gilzero

  Lets say I have a router that is connected to the Internet. An WAN IP address is given by ISP. It is using PPPoE ADSL, the IP address is not static, every time it connected, assigned a different IP address. There is an web server 192.168.0.100 running in the LAN. I heard something like DMZ + DynDNS can do the job? But not sure what these are and how they work. Any there way(s) to access the local node 192.168.0.100 via WAN, so that I can reach that node even I am not home. Thanks for any advice.

  Read the article

• Wireless is connected but no internet when PC Turns on

  - by mhesabi

  I have a PC that is connected to ADSL Modem router (linksys WAG54g2) directly via Ethernet cable And a laptop and also other devices such as another laptops and smarth phones. However when I turn On the PC or turn it off, some strange problem happens. My wireless network seems connected on laptop but there is no internet activity and can't open a webpage until I turn router off and on again manually. (other devices including the PC itself can't use the internet either) My router configured this way: Encapsulation: RFC 2516 PPPoE Multiplexing: LLC DHCP Server: Enabled and network sharing center IPv4 configuration is obtain IP address automatically How Can I fix this issue?

  Read the article

• can not access dlink 604 set up interface

  - by user36089

  Hello everyone I used dlink-di604 enthernet board as router to share web access. My ISP provides the service base on Ethernet rathern than base on Ethernet pppoe mode. It is manually setup ipv4, subnet mask , DNS, Gateway etc Log in using web user name&password. I use http://192.168.0.2 try to access dlink di604 setup inferface, but failed I call command ipconfig /all Dos shell displayed: Ethernet adapter Local Connection: Physical Address: 00-3c-56-79-19-49 IPv4 address:10.7.8.225 subnet mask: 255.255.255.0 default gate way: 10.7.8.1 DNS servers 10.10.10.10 What is the correct way to access dlink 604 setup interface and set to share web access? Welcome any comment Thanks interdev

  Read the article

• What router settings to use for wireless home network

  - by Question Overflow

  While looking at the setting of my wireless router, I am bewildered by the array of options available. Despite searching on Wikipedia to try to understand the various acronyms, I am still clueless to decide what is the best setting to use although the default works fine. Rather than calling the internet service provider (ISP) to ask them the correct settings, I hope to learn more about the differences between some of the options listed below, so that I would be able to make a more informed decision from now onwards: PPPoE vs PPPoA LLC vs VC-Mux Bridge vs Routed In addition, I would also like to know the significance of the following MTU VPI VCI And whether or when I should manually specify DNS?

  Read the article

• What is the best way to get the external internet gateway IP reported periodically?

  - by basilmir

  I have a OS X Server behind an airport extreme, serving services via opened ports on the airport. The server has a 10.0.x.x local address, always the same one. The airport extreme gets it's external IP address via PPPoE, and sometimes... once a week it changes. For security reasons WE ACTUALLY like this behavior. But i need a way to know the external IP address just in case i need to connect and do something to the server while on the outside. What can i do?

  Read the article

• Problem connecting to isp server using xl2tpd as client. Ubuntu server 13.04

  - by Deon Pretorius

  I have followed guides found on google and ubuntu support pages and can get xl2tpd connection up but only under the following conditions: 1 - ADSL model must be configured and connected to the ISP or 2 - ADSL modem in bridge mode I must have an existing PPPoe connection established. If neither of the above are active xl2tpd wont trigger pppd and connect to the isp and thus tunnel connection fails to connect to the L2TP server of the ISP. Am I doing something wrong; /etc/ppp/options.l2tpd.axxess ipcp-accept-local ipcp-accept-remote refuse-eap refuse-chap require-pap noccp noauth idle 1800 mtu 1200 mru 1200 defaultroute usepeerdns debug lock connect-delay 5000 name (name used for ppp connection) /etc/ppp/pap-secrets # * password (name used for ppp connection as above) * (ppp password supplied by isp) /etc/xl2tpd/xl2tpd.conf [global] ; Global parameters: auth file = /etc/xl2tpd/l2tp-secrets ; * Where our challenge secrets are access control = yes ; * Refuse connections without IP match debug tunnel = yes [lac axxess] lns = 196.30.121.50 ; * Who is our LNS? redial = yes ; * Redial if disconnected? redial timeout = 5 ; * Wait n seconds between redials max redials = 5 ; * Give up after n consecutive failures hidden bit = yes ; * User hidden AVP's? length bit = yes ; * Use length bit in payload? require pap = yes ; * Require PAP auth. by peer require chap = no ; * Require CHAP auth. by peer refuse chap = yes ; * Refuse CHAP authentication require authentication = yes ; * Require peer to authenticate name = BLA85003@axxess ; * Report this as our hostname ppp debug = yes ; * Turn on PPP debugging pppoptfile = /etc/ppp/options.l2tpd.axxess ; * ppp options file for this lac /etc/xl2tpd/l2tp-secrets # Secrets for authenticating l2tp tunnels # us them secret # * marko blah2 # zeus marko blah # * * interop * vzb_l2tp (*** secret supplied by isp) ^ isp server host name Any help will be greatly appreciated

  Read the article

• No internet connection using Edimax routers

  - by idan315

  I have two computers connected to a router, connected to my ADSL modem by PPPoE. One of those computrs use Windows XP, the other uses Windows 7. The computer using Windows 7 keeps getting limited or no connectivity, and I can't use it to connect to the internet. Connecting the computer to the modem without the router 'in the way' worked, and I was able to use the internet - which led me to believe that the problem is with my router. However, I have changed my router, and the problem persists. I am really lost on how to approach this problem. Possible leads: when I view the network information, I see that my computer is connected to 'Multiple Networks'. One of those is "Network 4" (probably my router), and the other is Unidentified network. I don't know how to make the "Unidentified Network" disappear, or why is it even there in the first place. When I try using "ipconfig", I have two default gateway IPs. The first is 0.0.0.0, and the second is the IP of my router (192.168.2.1). The first router was Edimax BR-6204Wg. The second one I've tried connecting is BR-6424n. Any ideas?

  Read the article

• Short POST data in HTTP

  - by Matt

  We're hosting a customer's Debian Linux web server. It's running a PHP based web application. The server is sitting behind our firewall with it's own virtual interface and port 80 is forwarded internally to a machine sitting in the DMZ. The issue we're having is that when data is posted to the server it seems to be being cut short for some users. It's reproducable for some users on the same box. But the same user sending the same data on the same lan on another PC it works. The data gets cut to around 1140 bytes I'm told. Any idea why this might be happening? The customer is blaming our firewall, but then surely we'd have issues with other services. I'm suspecting it's a problem with the website itself. Suggestions on how to isolate the problem would be of help. Our firewall is Astaro. EDIT: A customer has set the ethernet frame size temporarily to 500bytes on the server. This made it work for now! I know some of the customers are using an internet provider that runs PPPoE

  Read the article

• How to make DD-WRT router's (configured like a repeater) devices be accessible on LAN? (i.e. integrate DHCP for both routers)

  - by Annonomus Penguin

  I have a D-Link DIR-600-A1 router running DD-WRT (using the 601's firmware: except for the model number, they are near identical). It has an Atheros chip, so there is no "repeater" option. You can bypass this by setting the main radio as a client to the main router, and adding a virtual radio configured as an AP. You can then set up the credentials for connecting to the main router and allowing devices to connect to the repeater/router. I have a few devices on my network: Ethernet computers Server with Samba running WiFi devices connected to the main router I then wanted to add a repeater. I have a couple of other things on the repeater: WiFi Computer Other WiFi devices. Anyway, I wanted to connect my WiFi computer to the share on my server via Samba. However, for some reason, my router treats the main router as WAN, not another device. I've tried disabling the SPI firewall: However, that doesn't work. I've tried pinging my WiFi computer from my server. However, I can ping my server from my WiFi computer. AFAIK, they are on the same subset, just using different IPs: the main one uses 192.168.0.x and the repeater uses 192.168.1.x (starting at 100 for some reason). It seems as I need to configure my router(s) to work together for DHCP. I noticed there was a "DHCP forwarder" option, but I have no idea what that would do. A quick note: for some reason (that's beyond me) my ISP disabled the capability to bridge a WiFi to ethernet connection with the router they provide (something about PPPoE or similar...). The service rep I talked to when I was having issues after I changed ISPs said that, but they couldn't explain exactly what they were "blocking." How can I get DD-WRT to not treat the client connection as WAN and the router to recognize the devices connected to the repeater?

  Read the article

• Why can't I connect to computers on my network using our external IP address?

  - by Kivin

  My home network is serviced by an ADSL line. The modem is in bridged mode. The router performs the PPPoE. Three computers are connected to the router: two wired Windows 7 boxes and a Ubuntu Linux box over wifi. The computers are hosting various forms of services including FTP and HTTP. The router has port forwarding mapped from the relevant ports to the reserved IP addresses for the computers. If I attempt to connect to a server inside the network, such as ftp://67.xx.xxx.xxx from inside the network, the request times out. However if I connect using the internally mapped address, such as ftp://192.168.0.100, all is well. This is a nuisance for setting up software, especially on the laptop which needs to be able to phone home from anywhere, and I just don't have enough expertise with networking to know why this is occurring to even have a clue whether it can be solved or not. edit: It should be noted that the servers can be accessible outside the network - say, at the starbucks across the street - perfectly fine, using the ISP provided address and the appropriate port.

  Read the article

• How to connect 2 routers (Asmax and D-link) RJ11 vs RJ45 issue

  - by piobyz

  I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

  Read the article

• How to connect 2 routers (Asmax and D-link) RJ11 vs RJ45 issue

  - by piobyz

  I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

  Read the article

• sysctl.conf not running on boot

  - by Brian

  At what point is sysctl.conf supposed to be read during boot, and why might it not be running? I have the following settings which are not being applied when I reboot: net.bridge.bridge-nf-call-arptables = 0 net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-filter-pppoe-tagged = 0 net.bridge.bridge-nf-filter-vlan-tagged = 0 fs.nfs.nlm_udpport = 32768 fs.nfs.nlm_tcpport = 32768 The first section is needed for KVM bridging, and the second is to run the NFS lock manager on a known port. However, after booting, these values have not taken effect. If I run sysctl -p, then they do. This wouldn't be a huge issue, except that I can't figure out how to restart the lock manager without rebooting. I would really like to know why sysctl.conf isn't working at boot, but I'd settle for just being able to restart the lock manager. This is on Ubuntu server 10.04.2, kernel 2.6.32-31-server. I know some daemons check the permissions on their config files and refuse to work if they're too permissive, but sysctl.conf is 644 root:root, which I'm pretty sure is the default.

  Read the article

• Some HTTPS connections via NAT fail, but work on firewall itself.

  - by hnxn

  Hi, I am having trouble establishing some HTTPS connections from internal machines, even though these same connections work if initiated on the firewall itself. The firewall machine is running Ubuntu 10.04.1 and shorewall 4.4.6. The internet connection is Bell PPPoE DSL (in Canada). I have tried various MTU settings, it doesn't seem to make any difference. Other protocols (HTTP, FTP, etc) generally work. The problem seems to be limited to certain sites; this one never works from an internal machine, but always works from the firewall itself: From internal machine: $ wget https://images.fedex.com/images/ascend/shared/headers/nxgen/corp_logo.gif --2011-01-13 20:51:31-- https://images.fedex.com/images/ascend/shared/headers/nxgen/corp_logo.gif Resolving images.fedex.com... 184.24.96.69 Connecting to images.fedex.com|184.24.96.69|:443... connected. ^C From firewall: $ wget https://images.fedex.com/images/ascend/shared/headers/nxgen/corp_logo.gif --2011-01-13 20:58:28-- https://images.fedex.com/images/ascend/shared/headers/nxgen/corp_logo.gif Resolving images.fedex.com... 184.24.96.69 Connecting to images.fedex.com|184.24.96.69|:443... connected. HTTP request sent, awaiting response... 200 OK Length: 840 [image/gif] Saving to: `corp_logo.gif' 2011-01-13 20:58:28 (149 MB/s) - `corp_logo.gif' saved [840/840] This URL always works from both internal and firewall: https://encrypted.google.com/images/logos/ssl_logo_lg.gif Any troubleshooting tips would be greatly appreciated!

  Read the article

• Recommended open-source firmware for ASUS RT-N16

  - by MasterF

  I have recently acquired an ASUS RT-N16 router. My original plan for it was to install Tomato on it. However, after checking their website i found out that the firmware was not updated in the last 2 years. There seem to be a few updated mods but none of them really seemed mature/stable/well-documented. I would like to know what other people recommend as open-source firmware for this router. I know the answers will probably be subjective; so i will give a bit of background on my needs: for now i will only use the Wi-Fi on an Android phone the connection will not be shared with anyone (so QOS is optional) i want a stable (wired) connection on my PC (for online gaming etc.) i want the (wired) download/upload speeds to be as close as possible to those achieved by directly plugging the Ethernet cable to the PC's network card; i have a 100 Mbps connection my ISP uses PPPOE my technical level: i am a software developer and i have good knowledge of bash scripting, but no experience with networking Also, i know that i could probably just use the stock firmware (and maybe will use it for a while), but i'm interested in trying an open-source version (for more features, flexibility, as a learning exercise etc.)

  Read the article

< Previous Page | 1 2 3 4 5  | Next Page >