Search Results

Search found 701 results on 29 pages for 'sat'.

Page 4/29 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• LXC container can only access host via bridge

  - by vitaut

  I have an LXC container with i686 Ubuntu 12.04 running on a x86_64 Ubuntu 12.04 host. I've set up a bridge using instructions here. However the ping from the container only goes through to the host and not to other machines on the local network. Similarly only the host and not the other machines see the container OS. The host's /etc/network/interfaces file looks as follows: auto lo iface lo inet loopback iface eth0 inet manual auto br0 iface br0 inet dhcp bridge_ports eth0 bridge_fd 0 bridge_maxwait 0 The container's /etc/network/interfaces file looks as follows: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp And here's the relevant part of the container's config: lxc.network.type=veth lxc.network.link=br0 lxc.network.flags=up Any ideas what I'm doing wrong? Additional info: The output of iptables-save on host: $ sudo iptables-save # Generated by iptables-save v1.4.12 on Sat Oct 26 06:06:48 2013 *filter :INPUT ACCEPT [6854:721708] :FORWARD ACCEPT [4067:538895] :OUTPUT ACCEPT [4967:522405] COMMIT # Completed on Sat Oct 26 06:06:48 2013 # Generated by iptables-save v1.4.12 on Sat Oct 26 06:06:48 2013 *nat :PREROUTING ACCEPT [82235:21547307] :INPUT ACCEPT [16:1070] :OUTPUT ACCEPT [9386:583359] :POSTROUTING ACCEPT [14693:1291952] -A POSTROUTING -s 10.0.3.0/24 ! -d 10.0.3.0/24 -j MASQUERADE COMMIT # Completed on Sat Oct 26 06:06:48 2013 The output of brctl show on host: $ brctl show bridge name bridge id STP enabled interfaces br0 8000.080027409684 no eth0 vethBkwWyV The output of ifconfig br0 on host: $ ifconfig br0 br0 Link encap:Ethernet HWaddr 08:00:27:40:96:84 inet addr:192.168.1.11 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe40:9684/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:232863 errors:0 dropped:0 overruns:0 frame:0 TX packets:59518 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:34437354 (34.4 MB) TX bytes:198492871 (198.4 MB) The output of ifconfig eth0 on host: $ ifconfig eth0 eth0 Link encap:Ethernet HWaddr 08:00:27:40:96:84 inet6 addr: fe80::a00:27ff:fe40:9684/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:299419 errors:0 dropped:0 overruns:0 frame:0 TX packets:203569 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:59077446 (59.0 MB) TX bytes:372056540 (372.0 MB) The output of ifconfig eth0 on container: $ ifconfig eth0 eth0 Link encap:Ethernet HWaddr 00:16:3e:74:08:2b inet addr:192.168.1.12 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::216:3eff:fe74:82b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:81 errors:0 dropped:0 overruns:0 frame:0 TX packets:113 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8506 (8.5 KB) TX bytes:9021 (9.0 KB)

  Read the article

• Why does NX Client for Windows silently closes after connection?

  - by pavel

  Hey! I connect remotely to my Ubuntu server from Vista machine. Now I need to run a GUI application on the server (Wireshark). So I decided to use FreeNX server/client to view Ubuntu GUI on Vista I have successfully installed FreeNX on Ubuntu and NX Client on Vista. I was following this guide Unfortunately, now I found myself stuck with the following problem. At the client, the !M logo window appears, but after a few seconds that window just closes, even without showing any error message. Guys, I'm really stuck, please help! Maybe I should have installed some graphical environment on the server? These are the details from NX client, it seems there are no errors. ----------------- Info: Display running with pid '7768' and handler '0x670d24'. NXPROXY - Version 3.4.0 Copyright (C) 2001, 2007 NoMachine. See http://www.nomachine.com/ for more information. Info: Proxy running in client mode with pid '2168'. Session: Starting session at 'Sat Dec 19 10:58:35 2009'. Warning: Connected to remote version 3.3.0 with local version 3.4.0. Info: Connection with remote proxy completed. Info: Using WAN link parameters 768/24/1/0. Info: Using cache parameters 4/4096KB/16384KB/16384KB. Info: Using pack method 'adaptive-9' with session 'kde'. Info: Using ZLIB data compression 1/1/32. Info: Using ZLIB stream compression 1/1. Info: No suitable cache file found. Info: Forwarding X11 connections to display ':0'. Info: Listening to font server connections on port '11000'. Session: Session started at 'Sat Dec 19 10:58:35 2009'. Info: Established X server connection. Info: Using shared memory parameters 0/0K. Session: Terminating session at 'Sat Dec 19 10:58:37 2009'. Session: Session terminated at 'Sat Dec 19 10:58:37 2009'. -----------

  Read the article

• How is it possible for mod_wsgi to be compiled against Python 2.7.3 but use the 2.7.2 runtime?

  - by Ian William Kohl

  The following is what appears in my error_log: [Sat Nov 17 23:13:14 2012] [warn] mod_wsgi: Compiled for Python/2.7.3. [Sat Nov 17 23:13:14 2012] [warn] mod_wsgi: Runtime using Python/2.7.2. If I check my $PATH variable and even in /etc/paths, /usr/local/bin (which contains Python 2.7.3) comes before /usr/bin (which contains Python 2.7.2). Is there some other path that I'm missing out on? How can I get the correct runtime to be used?

  Read the article

• problem with date returning wrong day although the timestamp is correct!

  - by Spiros

  I have a bizzare problem with php date function. code: $numDays = 8; $date = strtotime('2010-11-06'); for ($i=1; $i<=$numDays; $i++) { $thisDay = date("D, d M Y", $date); print ($thisDay.'<br>'); $date+=86400; // add one day to timestamp } result on my server (local host, windows): Sat, 06 Nov 2010 Sun, 07 Nov 2010 Mon, 08 Nov 2010 Tue, 09 Nov 2010 Wed, 10 Nov 2010 Thu, 11 Nov 2010 Fri, 12 Nov 2010 Sat, 13 Nov 2010 Result on my web server (linux) Sat, 06 Nov 2010 *Sun, 07 Nov 2010 Sun, 07 Nov 2010* Mon, 08 Nov 2010 Tue, 09 Nov 2010 Wed, 10 Nov 2010 Thu, 11 Nov 2010 Fri, 12 Nov 2010 Notice how Sun, 07 Nov 2010 appears twice on the remote server?? Why is this happening? can anyone explain this Behavior?

  Read the article

• Query for Joining Two Tables With Possible Multiple Mapping

  - by Dharmendra Mohapatra

  First_table srno wono Actual_Start_Date Actual_End_Date 1 31 2012-06-02 2012-06-05 2 32 2012-06-05 2012-06-22 3 33 2012-06-11 2012-06-23 4 34 2012-06-23 2012-06-30 5 A-2 2012-06-24 2012-06-25 6 BU 2012-06-24 2012-06-26 7 40 2012-06-25 2012-06-27 second_table srno wono Base_start_date Base_end_date uploadhistoryid 1 31 2012-06-05 2012-06-05 1 2 32 2012-06-11 2012-06-12 2 3 32 2012-06-15 2012-06-17 3 4 32 2012-06-18 2012-06-20 4 5 33 2012-06-22 2012-06-25 5 5 33 2012-06-23 2012-06-25 5 Result Required SET ANSI_NULLS ON GO SET QUOTED_IDENTIFIER ON GO ALTER PROCEDURE [dbo].[Reports_Subanalysis] ( @WONo VARCHAR(20) ) AS BEGIN SELECT 'SAT' AS stage, s.Base_start_date AS start_date, s.Base_end_date AS end_date, f.Actual_Start_Date AS Actual_Start_Date, f.Actual_end_Date AS Actual_End_Date FROM First_table f, second_table B WHERE A.wOno=B.nOno AND f.uploadhistoryid in (SELECT min(uploadhistoryid) FROM second_table C WHERE f.wono = C.wono) AND b.wono=@WONo END when I pass '32' Result stage start_date end_date Actual_Start_Date Actual_End_Date SAT 2012-06-11 2012-06-12 2012-06-05 2012-06-05 how Can I get the result like this when I pass non matching value like 'BU' stage start_date end_date Actual_Start_Date Actual_End_Date SAT NULL NULL 2012-06-24 2012-06-26 What modification do I need in my routine?

  Read the article

• python filter can't output

  - by Jesse Siu

  i create filter by python to the log file like Sat Jun 2 03:32:13 2012 [pid 12461] CONNECT: Client "66.249.68.236" Sat Jun 2 03:32:13 2012 [pid 12460] [ftp] OK LOGIN: Client "66.249.68.236", anon password "[email protected]" Sat Jun 2 03:32:14 2012 [pid 12462] [ftp] OK DOWNLOAD: Client "66.249.68.236", "/pub/10.5524/100001_101000/100022/readme.txt", 451 bytes, 1.39Kbyte/sec the script is import time lines=[] f= open("/opt/CLiMB/Storage1/log/vsftp.log") line = f.readline() lines=[line for line in f] def OnlyRecent(line): if time.strptime(line.split("[")[0].strip(),"%a %b %d %H:%M:%S %Y") < time.time()-(60*60*24*2): return True return False print"\n".join(filter(OnlyRecent,lines)) f.close() but when i run this script, it continue running but didn't show anything until i stop it. Why it can't shows records happened in 2 days.

  Read the article

• date() returning wrong day although the timestamp is correct!

  - by Spiros

  I have a bizzare problem with php date function. code: $numDays = 8; $date = strtotime('2010-11-06'); for ($i=1; $i<=$numDays; $i++) { $thisDay = date("D, d M Y", $date); print ($thisDay.'<br>'); $date+=86400; // add one day to timestamp } result on my server (local host, windows): Sat, 06 Nov 2010 Sun, 07 Nov 2010 Mon, 08 Nov 2010 Tue, 09 Nov 2010 Wed, 10 Nov 2010 Thu, 11 Nov 2010 Fri, 12 Nov 2010 Sat, 13 Nov 2010 Result on my web server (linux) Sat, 06 Nov 2010 *Sun, 07 Nov 2010 Sun, 07 Nov 2010* Mon, 08 Nov 2010 Tue, 09 Nov 2010 Wed, 10 Nov 2010 Thu, 11 Nov 2010 Fri, 12 Nov 2010 Notice how Sun, 07 Nov 2010 appears twice on the remote server?? Why is this happening? can anyone explain this Behavior?

  Read the article

• python compare time

  - by Jesse Siu

  i want to using python create filter for a log file. get recent 7 days record. but when i didn't know how to compare time. like current time is 11/9/2012, i want to get records from 04/9/2012 to now the log file like Sat Sep 2 03:32:13 2012 [pid 12461] CONNECT: Client "66.249.68.236" Sat Sep 2 03:32:13 2012 [pid 12460] [ftp] OK LOGIN: Client "66.249.68.236", anon password "[email protected]" Sat Sep 2 03:32:14 2012 [pid 12462] [ftp] OK DOWNLOAD: Client "66.249.68.236", "/pub/10.5524/100001_101000/100022/readme.txt", 451 i using this one def OnlyRecent(line): print time.strptime(line.split("[")[0].strip(),"%a %b %d %H:%M:%S %Y") print time.time() if time.strptime(line.split("[")[0].strip(),"%a %b %d %H:%M:%S %Y") < time.time(): return True return False But it shows (2012, 9, 2, 3, 32, 13, 5, 246, -1) 1347332968.08 (2012, 9, 2, 3, 32, 13, 5, 246, -1) 1347332968.08 (2012, 9, 2, 3, 32, 14, 5, 246, -1) 1347332968.08 the time format is different, and it can't compare time. So how to set this comparison in 7 days. Thanks

  Read the article

• Swept AABB vs Line Segment 2D

  - by Larolaro

  I've really exhausted as much as Google has to give, I've spent a solid week googling every combination of words for an "AABBvsLine sweep", downloaded countless collision demos, dissected SAT intersection examples and an AABBvsAABB sweep trying to figure out how to approach this. I've not found a single thing covering this specific pairing. Can anyone shed any light on how to get the hit time of a swept AABB vs a Line segment in 2D? I'm still getting familiar with the SAT but I do know how to implement it to a degree, I'm just not sure how to extract the hit time from the velocity in the non axis aligned separating axes for the sweep. I really would appreciate anything at the moment, some code or even some helpful links, I'm at my wits end!

  Read the article

• Narrow-phase collision detection algorithms

  - by Marian Ivanov

  There are three phases of collision detection. Broadphase: It loops between all objecs that can interact, false positives are allowed, if it would speed up the loop. Narrowphase: Determines whether they collide, and sometimes, how, no false positives Resolution: Resolves the collision. The question I'm asking is about the narrowphase. There are multiple algorithms, differing in complexity and accuracy. Hitbox intersection: This is an a-posteriori algorithm, that has the lowest complexity, but also isn't too accurate, Color intersection: Hitbox intersection for each pixel, a-posteriori, pixel-perfect, not accuratee in regards to time, higher complexity Separating axis theorem: This is used more often, accurate for triangles, however, a-posteriori, as it can't find the edge, when taking last frame in account, it's more stable Linear raycasting: A-priori algorithm, useful for semi-realistic-looking physics, finds the intersection point, even more accurate than SAT, but with more complexity Spline interpolation: A-priori, even more accurate than linear rays, even more coplexity. There are probably many more that I've forgot about. The question is, in when is it better to use SAT, when rays, when splines, and whether there is anything better.

  Read the article

• RAID1: can't replace faulty spare (marked again as 'faulty spare' within seconds)

  - by user212475

  I got a problem that I cannot solve: Our fileserver runs XUbuntu and 3 RAID1s. One has a problem since monday: it consists of sdb and sdc. sdb was marked as faulty by mdadm for unknown reasons. I used --remove to remove it from the RAID and then to add it by --add. All was fine, re-syncing started but never got above 0% and after a few seconds, sdb was again marked as 'faulty spare' (and therefore the RAID degraded, but clean). So I saved the first 512 byte of the old sdb to a file, bought a new HDD of same size (4TB), shut down the computer and replaced sdb physically, switched the computer back on and wrote the 512 byte back to the new drive to have the same partition info as the old drive (both are the same type, from same company). But the new drive shows the same behaviour as the old: I can add, re-syncing starts and after a few seconds its marked as 'faulty spare'. Here exactly what i did: mdadm --remove /dev/md/1 /dev/sdb maadm --detail /dev/md/1 gives me: /dev/md/1: Version : 1.2 Creation Time : Sat Jun 8 22:32:05 2013 Raid Level : raid1 Array Size : 3906887360 (3725.90 GiB 4000.65 GB) Used Dev Size : 3906887360 (3725.90 GiB 4000.65 GB) Raid Devices : 2 Total Devices : 1 Persistence : Superblock is persistent Update Time : Thu Nov 7 06:56:13 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 0 Spare Devices : 0 Name : File-Server:1 (local to host File-Server) UUID : 44ed561f:b733e946:e69820f4:aba9b223 Events : 2424 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 32 1 active sync /dev/sdc mdadm --add /dev/md/1 /dev/sdb mdadm --detail /dev/md/1 gives me: Version : 1.2 Creation Time : Sat Jun 8 22:32:05 2013 Raid Level : raid1 Array Size : 3906887360 (3725.90 GiB 4000.65 GB) Used Dev Size : 3906887360 (3725.90 GiB 4000.65 GB) Raid Devices : 2 Total Devices : 2 Persistence : Superblock is persistent Update Time : Thu Nov 7 06:57:49 2013 State : clean, degraded, recovering Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 Rebuild Status : 0% complete Name : File-Server:1 (local to host File-Server) UUID : 44ed561f:b733e946:e69820f4:aba9b223 Events : 2431 Number Major Minor RaidDevice State 2 8 16 0 faulty spare rebuilding /dev/sdb 1 8 32 1 active sync /dev/sdc and after a few seconds: /dev/md/1: Version : 1.2 Creation Time : Sat Jun 8 22:32:05 2013 Raid Level : raid1 Array Size : 3906887360 (3725.90 GiB 4000.65 GB) Used Dev Size : 3906887360 (3725.90 GiB 4000.65 GB) Raid Devices : 2 Total Devices : 2 Persistence : Superblock is persistent Update Time : Thu Nov 7 06:57:50 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 Name : File-Server:1 (local to host File-Server) UUID : 44ed561f:b733e946:e69820f4:aba9b223 Events : 2436 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 32 1 active sync /dev/sdc 2 8 16 - faulty spare /dev/sdb same behaviour if I zero the superblock (mdadm --zero-superblock /dev/sdb) before adding sdb. I do all commands as root and the system holds 3 more 4TB drives, ie the mainboard can handle them. The old harddrive was checked for errors using badblocks, but all is fine. Does anybody have any idea, what the problem is?

  Read the article

• mod_deflate doesn't work [closed]

  - by kikio

  I want to gzip my static files. so put this in .htaccess: <IfModule mod_deflate.c> AddOutputFilterByType DEFLATE text/text text/html text/plain text/xml text/css application/x-javascript application/javascript </IfModule> and looked for mod_deflate in phpinfo() output Loaded Modules section, and I found it. But when I track server responses with Firebug, no gzipped file can be found: HTTP/1.1 200 OK Date: Sat, 08 Sep 2012 21:41:21 GMT Last-Modified: Sat, 08 Sep 2012 21:26:04 GMT Accept-Ranges: bytes Cache-Control: max-age=604800 Expires: Sat, 15 Sep 2012 21:41:21 GMT Vary: Accept-Encoding Keep-Alive: timeout=3, max=50 Connection: Keep-Alive Content-Type: text/css Content-Length: 18206 What's the problem? I'm sure I have mod_deflate enabled (according to php apache_get_modules()). UPDATE: the request headers: GET /d/jquery-ui.css HTTP/1.1 Host: 127.0.0.1 User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64; rv:15.0) Gecko/20100101 Firefox/15.0.1 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-us,en;q=0.5 Accept-Encoding: gzip, deflate DNT: 1 Connection: keep-alive Pragma: no-cache Cache-Control: no-cache

  Read the article

• How are spam e-mails filtered ?

  - by kevindqc

  Hello. I'm just wondering how some e-mails get past the spam filter, and some don't? Everyday I get World of Warcraft phishing emails that get past the filter... For example, here's a phishing email (just the header) I got in my inbox, and not in my junk mail: X-Message-Delivery: Vj0xLjE7dXM9MDtsPTA7YT0wO0Q9MjtTQ0w9Ng== X-Message-Status: n:0 X-SID-PRA: [email protected] X-AUTH-Result: NONE X-Message-Info: M98loaK0Lo27IVRxloyPIZmAwUHKn18nx0o/idLdvGYjK48i19NuvFOnRFYGWE+HdIrNJpi1XaYx0gaAV13cgRnkWSzgHKG1 Received: from blizzard.com ([204.45.59.37]) by SNT0-MC3-F21.Snt0.hotmail.com with Microsoft SMTPSVC(6.0.3790.3959); Sat, 10 Apr 2010 06:38:24 -0700 Received: from hxeabjlh ([192.168.1.165]) (envelope-sender <[email protected]>) by 192.168.1.111 with ESMTP for <[email protected]>; Sat, 10 Apr 2010 08:43:24 -0500 Reply-To: <[email protected]> Sender: [email protected] Message-ID: <DE567AFB9E2F3DD985A2D9A8D12D2917@hxeabjlh> From: "[email protected]" <[email protected]> To: <[email protected]> Subject: World of Warcraft Account Password verification Date: Sat, 10 Apr 2010 21:38:10 +0800 MIME-Version: 1.0 Content-Type: multipart/alternative; boundary="----=_NextPart_000_04EE_0137659E.1AA23350" X-Priority: 3 X-MSMail-Priority: Normal X-Mailer: Microsoft Outlook Express 6.00.2900.5512 X-MimeOLE: Produced By Microsoft MimeOLE V6.00.2900.5512 Return-Path: [email protected] X-OriginalArrivalTime: 10 Apr 2010 13:38:24.0607 (UTC) FILETIME=[17F3A6F0:01CAD8B3] From what I understand, when you send an email with SMTP, you can specify any hostname in the "HELO" command. Here, the spammer specified "blizzard.com". And he sent his email through Hotmail using Outlook Express. I just don't understand how this gets past the spam filter? There's this SPF thing that seems to exist... but it doesn't seem to be used by blizzard? I'm on Windows, and if I use nslookup to look for the TXT records of blizzard.com and worldofwarcraft.com, I don't see a thing.... so blizzard is not using SPF? Why would that be?

  Read the article

• javascript date comparison

  - by ash34

  Hi, I haven't done much js. I am trying to compare two dates. From jconsole a = ["01/01/2010","01/02/2010","01/03/2010"] date1 = new Date('01/02/2010') Sat Jan 02 2010 00:00:00 GMT-0800 (PST) date2 = new Date(a[1]) Sat Jan 02 2010 00:00:00 GMT-0800 (PST) date1 == date2 false Can someone tell me why this does not match? thanks.

  Read the article

• Sorting and Re-arranging List of HashMaps

  - by HonorGod

  I have a List which is straight forward representation of a database table. I am trying to sort and apply some magic after the data is loaded into List of HashMaps. In my case this is the only hard and fast way of doing it becoz I have a rules engine that actually updates the values in the HashMap after several computations. Here is a sample data representation of the HashMap (List of HashMap) - {fromDate=Wed Mar 17 10:54:12 EDT 2010, eventId=21, toDate=Tue Mar 23 10:54:12 EDT 2010, actionId=1234} {fromDate=Wed Mar 17 10:54:12 EDT 2010, eventId=11, toDate=Wed Mar 17 10:54:12 EDT 2010, actionId=456} {fromDate=Sat Mar 20 10:54:12 EDT 2010, eventId=20, toDate=Thu Apr 01 10:54:12 EDT 2010, actionId=1234} {fromDate=Wed Mar 24 10:54:12 EDT 2010, eventId=22, toDate=Sat Mar 27 10:54:12 EDT 2010, actionId=1234} {fromDate=Wed Mar 17 10:54:12 EDT 2010, eventId=11, toDate=Fri Mar 26 10:54:12 EDT 2010, actionId=1234} {fromDate=Sat Mar 20 10:54:12 EDT 2010, eventId=11, toDate=Wed Mar 31 10:54:12 EDT 2010, actionId=1234} {fromDate=Mon Mar 15 10:54:12 EDT 2010, eventId=12, toDate=Wed Mar 17 10:54:12 EDT 2010, actionId=567} I am trying to achieve couple of things - 1) Sort the list by actionId and eventId after which the data would look like - {fromDate=Wed Mar 17 10:54:12 EDT 2010, eventId=11, toDate=Wed Mar 17 10:54:12 EDT 2010, actionId=456} {fromDate=Mon Mar 15 10:54:12 EDT 2010, eventId=12, toDate=Wed Mar 17 10:54:12 EDT 2010, actionId=567} {fromDate=Wed Mar 24 10:54:12 EDT 2010, eventId=22, toDate=Sat Mar 27 10:54:12 EDT 2010, actionId=1234} {fromDate=Wed Mar 17 10:54:12 EDT 2010, eventId=21, toDate=Tue Mar 23 10:54:12 EDT 2010, actionId=1234} {fromDate=Sat Mar 20 10:54:12 EDT 2010, eventId=20, toDate=Thu Apr 01 10:54:12 EDT 2010, actionId=1234} {fromDate=Wed Mar 17 10:54:12 EDT 2010, eventId=11, toDate=Fri Mar 26 10:54:12 EDT 2010, actionId=1234} {fromDate=Sat Mar 20 10:54:12 EDT 2010, eventId=11, toDate=Wed Mar 31 10:54:12 EDT 2010, actionId=1234} 2) If we group the above list by actionId they would be resolved into 3 groups - actionId=1234, actionId=567 and actionId=456. Now here is my question - For each group having the same eventId, I need to update the records so that they have wider fromDate to toDate. Meaning, if you consider the last two rows they have same actionId = 1234 and same eventId = 11. Now we can to pick the least fromDate from those 2 records which is Wed Mar 17 10:54:12 and farther toDate which is Wed Mar 31 10:54:12 and update those 2 record's fromDate and toDate to Wed Mar 17 10:54:12 and Wed Mar 31 10:54:12 respectively. Any ideas? PS: I already have some pseudo code to start with. import java.util.ArrayList; import java.util.Calendar; import java.util.Collections; import java.util.Comparator; import java.util.Date; import java.util.HashMap; import java.util.List; import org.apache.commons.lang.builder.CompareToBuilder; public class Tester { boolean ascending = true ; boolean sortInstrumentIdAsc = true ; boolean sortEventTypeIdAsc = true ; public static void main(String args[]) { Tester tester = new Tester() ; tester.printValues() ; } public void printValues () { List<HashMap<String,Object>> list = new ArrayList<HashMap<String,Object>>() ; HashMap<String,Object> map = new HashMap<String,Object>(); map.put("actionId", new Integer(1234)) ; map.put("eventId", new Integer(21)) ; map.put("fromDate", getDate(1) ) ; map.put("toDate", getDate(7) ) ; list.add(map); map = new HashMap<String,Object>(); map.put("actionId", new Integer(456)) ; map.put("eventId", new Integer(11)) ; map.put("fromDate", getDate(1)) ; map.put("toDate", getDate(1) ) ; list.add(map); map = new HashMap<String,Object>(); map.put("actionId", new Integer(1234)) ; map.put("eventId", new Integer(20)) ; map.put("fromDate", getDate(4) ) ; map.put("toDate", getDate(16) ) ; list.add(map); map = new HashMap<String,Object>(); map.put("actionId", new Integer(1234)) ; map.put("eventId", new Integer(22)) ; map.put("fromDate",getDate(8) ) ; map.put("toDate", getDate(11)) ; list.add(map); map = new HashMap<String,Object>(); map.put("actionId", new Integer(1234)) ; map.put("eventId", new Integer(11)) ; map.put("fromDate",getDate(1) ) ; map.put("toDate", getDate(10) ) ; list.add(map); map = new HashMap<String,Object>(); map.put("actionId", new Integer(1234)) ; map.put("eventId", new Integer(11)) ; map.put("fromDate",getDate(4) ) ; map.put("toDate", getDate(15) ) ; list.add(map); map = new HashMap<String,Object>(); map.put("actionId", new Integer(567)) ; map.put("eventId", new Integer(12)) ; map.put("fromDate", getDate(-1) ) ; map.put("toDate",getDate(1)) ; list.add(map); System.out.println("\n Before Sorting \n "); for(int j = 0 ; j < list.size() ; j ++ ) System.out.println(list.get(j)); Collections.sort ( list , new HashMapComparator2 () ) ; System.out.println("\n After Sorting \n "); for(int j = 0 ; j < list.size() ; j ++ ) System.out.println(list.get(j)); } public static Date getDate(int days) { Calendar cal = Calendar.getInstance(); cal.setTime(new Date()); cal.add(Calendar.DATE, days); return cal.getTime() ; } public class HashMapComparator2 implements Comparator { public int compare ( Object object1 , Object object2 ) { if ( ascending == true ) { return new CompareToBuilder() .append(( ( HashMap ) object1 ).get ( "actionId" ), ( ( HashMap ) object2 ).get ( "actionId" )) .append(( ( HashMap ) object2 ).get ( "eventId" ), ( ( HashMap ) object1 ).get ( "eventId" )) .toComparison(); } else { return new CompareToBuilder() .append(( ( HashMap ) object2 ).get ( "actionId" ), ( ( HashMap ) object1 ).get ( "actionId" )) .append(( ( HashMap ) object2 ).get ( "eventId" ), ( ( HashMap ) object1 ).get ( "eventId" )) .toComparison(); } } } }

  Read the article

• No device file for partition on logical volume (Linux LVM)

  - by Brian

  I created a logical volume (scandata) containing a single ext3 partition. It is the only logical volume in its volume group (case4t). Said volume group is comprised by 3 physical volumes, which are three primary partitions on a single block device (/dev/sdb). When I created it, I could mount the partition via the block device /dev/mapper/case4t-scandatap1. Since last reboot the aforementioned block device file has disappeared. It may be of note -- I'm not sure -- that my superior (a college professor) had prompted this reboot by running sudo chmod -R [his name] /usr/bin, which obliterated all suid in its path, preventing the both of us from sudo-ing. That issue has been (temporarily) rectified via this operation. Now I'll cut the chatter and get started with the terminal dumps: $ sudo pvs; sudo vgs; sudo lvs Logging initialised at Sat Jan 8 11:42:34 2011 Set umask to 0077 Scanning for physical volume names PV VG Fmt Attr PSize PFree /dev/sdb1 case4t lvm2 a- 819.32G 0 /dev/sdb2 case4t lvm2 a- 866.40G 0 /dev/sdb3 case4t lvm2 a- 47.09G 0 Wiping internal VG cache Logging initialised at Sat Jan 8 11:42:34 2011 Set umask to 0077 Finding all volume groups Finding volume group "case4t" VG #PV #LV #SN Attr VSize VFree case4t 3 1 0 wz--n- 1.69T 0 Wiping internal VG cache Logging initialised at Sat Jan 8 11:42:34 2011 Set umask to 0077 Finding all logical volumes LV VG Attr LSize Origin Snap% Move Log Copy% Convert scandata case4t -wi-a- 1.69T Wiping internal VG cache $ sudo vgchange -a y Logging initialised at Sat Jan 8 11:43:14 2011 Set umask to 0077 Finding all volume groups Finding volume group "case4t" 1 logical volume(s) in volume group "case4t" already active 1 existing logical volume(s) in volume group "case4t" monitored Found volume group "case4t" Activated logical volumes in volume group "case4t" 1 logical volume(s) in volume group "case4t" now active Wiping internal VG cache $ ls /dev | grep case4t case4t $ ls /dev/mapper case4t-scandata control $ sudo fdisk -l /dev/case4t/scandata Disk /dev/case4t/scandata: 1860.5 GB, 1860584865792 bytes 255 heads, 63 sectors/track, 226203 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00049bf5 Device Boot Start End Blocks Id System /dev/case4t/scandata1 1 226203 1816975566 83 Linux $ sudo parted /dev/case4t/scandata print Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/case4t-scandata: 1861GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 1861GB 1861GB primary ext3 $ sudo fdisk -l /dev/sdb Disk /dev/sdb: 1860.5 GB, 1860593254400 bytes 255 heads, 63 sectors/track, 226204 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00000081 Device Boot Start End Blocks Id System /dev/sdb1 1 106955 859116006 83 Linux /dev/sdb2 113103 226204 908491815 83 Linux /dev/sdb3 106956 113102 49375777+ 83 Linux Partition table entries are not in disk order $ sudo parted /dev/sdb print Model: DELL PERC 6/i (scsi) Disk /dev/sdb: 1861GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 880GB 880GB primary reiserfs 3 880GB 930GB 50.6GB primary 2 930GB 1861GB 930GB primary I find it a bit strange that partition one above is said to be reiserfs, or if it matters -- it was previously reiserfs, but LVM recognizes it as a PV. To reiterate, neither /dev/mapper/case4t-scandatap1 (which I had used previously) nor /dev/case4t/scandata1 (as printed by fdisk) exists. And /dev/case4t/scandata (no partition number) cannot be mounted: $sudo mount -t ext3 /dev/case4t/scandata /mnt/new mount: wrong fs type, bad option, bad superblock on /dev/mapper/case4t-scandata, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so All I get on syslog is: [170059.538137] VFS: Can't find ext3 filesystem on dev dm-0. Thanks in advance for any help you can offer, Brian P.S. I am on Ubuntu GNU/Linux 2.6.28-11-server (Jaunty) (out of date, I know -- that's on the laundry list).

  Read the article

• Yahoo is sending our server's transactional email to the Spam folder, even though we have set up SPF and DKIM

  - by Derrick Miller

  Yahoo Mail is sending our server's transactional emails to the Spam folder, even though we have taken quite a few anti-spam steps. By contrast, Gmail allows the messages through to the inbox just fine. Here are the things which are in place: SPF is set up for the domain holsteinplaza.com. Yahoo reports spf=pass in the message headers. DKIM is set up for the domain holsteinplaza.com. Yahoo reports dkim=pass in the message headers. We have a proper reverse DNS entry for the sending mail server. Name - IP matches IP - Name. Neither Domainkeys nor SenderID are set up. From what I can tell, DKIM is the way of the future, and there is not much to be gained from adding Domainkeys or SenderID. Following are the headers. Any ideas what more I should do to get Yahoo to stop flagging the emails as spam? From Holstein Plaza Auctions Sat Jun 25 18:30:08 2011 X-Apparently-To: [email protected] via 98.138.90.132; Sat, 25 Jun 2011 18:30:11 -0700 Return-Path: <[email protected]> X-YahooFilteredBulk: 70.32.113.42 Received-SPF: pass (domain of holsteinplaza.com designates 70.32.113.42 as permitted sender) X-YMailISG: i_vaA_QWLDuLOmXhDjUv3aBKJl5Un6EiP6Yk2m4yn3jeEuYK MkhpqIt9zDUbHARCwXrhl9pqjTANurGVca7gytSs.mryWVQcbWBx.DaItWRb VcyrIzwMzXKCSeu06H2a.cJ7HG5vJLJaKmHUUI_1ttXKn_Aegiu5yHvFX83R Lpth0witO9zfaKvOMaJV3LAxpIpFOydwvq1cqjZ8nURxQbxM3Cl.QW7MxxrC 09qLVn_D_xSdU94QdU22IsVmlaRHv.uU5dnIazu.KSkhKpYykDoZA2SH0SY4 JmTZj3LP8N926xXVDzYQ5K6QvKuJL5g0d9pYZx3KC59sgIu5oHlJ3Q15RdKb f3OJw0PR6oIyJ2yStVr8vfbDgOfj3qig03.Tw6g6MMNpv1G7Cuol4oJeUaYP xELxX6dHgBgCSuWMcbsrxbK4BIXcS2qhpMqYQ4Isk.XXyA8uvmFXyvgc1ds5 8jo0rW.Wsw.55Z.KTPaQ0gHXj0T3OGppYMELSJv1iuhPyyAnZpmq01CU0Qd5 CcRgdyW3HaqhmpXqJCS0Clo16zXA4HmAjR0tgIQrHRLc3D9N02AOzvmDgCb1 vCh0p00QeKVq8UNkcShPRxZFKi9khtkLhPBlXEKkhJ76zyDmHUxTY.dQHVVD 8D2hx7BxbqI9DINI8x5oR5Q8hYkZqHYQsmGNkaU77O2BnsEv5WxMEmzrBJ4Z h8zGCidgYPiZycZfnfaBp0Xb4tya2WMTN45W02JFcO1qq_UMJ9xPeqZhPEj. j9YvBAC8324GGF.c8eWcNB2VB34QHgTcVUl3.c0XUCuncls9Cyg4L7AoIdCi HvAklSzDDu9nW6732VEipV9FJ_JkDupDNQU2hfiPG.3OeF8GwTnVYnEn0EiZ aO0NCnZhXuLDcN3K7ml3846yRdASvzPFs9s4aJkzR0FkhVvptiMBEOdRkKdG wHWmvWpK4GTZpW4yU7CnKpW2MiWWn1MP0h_CCZFKs5.3mfmfPjPVIABN_RuU Q8ex5hdKnKlQiqK56LzcPRnYmNtrwdsUX9CYn9d6cPpXR_Bi5jrNJMNzdFvq lGO0CBT4QPe2V45U8PtpMitttuDA1cCvmyBPFswxNlL0jyX0a_W.vl0YW5.d HhDItpHhDxKRUscM28IR.exetq4QCzyM X-Originating-IP: [70.32.113.42] Authentication-Results: mta1267.mail.ac4.yahoo.com from=holsteinplaza.com; domainkeys=neutral (no sig); from=holsteinplaza.com; dkim=pass (ok) Received: from 127.0.0.1 (EHLO predator.axis80.com) (70.32.113.42) by mta1267.mail.ac4.yahoo.com with SMTP; Sat, 25 Jun 2011 18:30:11 -0700 Received: (qmail 1440 invoked by uid 48); 25 Jun 2011 21:30:09 -0400 To: [email protected] Subject: this is a test X-PHPMAILER-DKIM: phpmailer.worxware.com DKIM-Signature: v=1; a=rsa-sha1; q=dns/txt; l=203; s=auction; t=1309051808; c=relaxed/simple; h=From:To:Subject; d=holsteinplaza.com; [email protected]; z=From:=20Holstein=20Plaza=20Auctions=20<[email protected]> |To:[email protected] |Subject:=20this=20is=20a=20test; bh=B3Tw5AQb1va627KEoazuFEBZ0fg=; b=oQ5uFq+oekPTGhszyIritjuuIAi3qPNyeitu+aWMhdx3oC6O2j5hJsDFpK0sS5fms7QdnBkBcEzT0iekEvn9EfAdCkGZ2KrtEC0yv7QKQcrjXxy07GJpj9nq0LYbgOuPdw8mGvKxlRZ+jFBX0DRJm0xXFLkr+MEaILw7adHTCCM= Date: Sat, 25 Jun 2011 21:30:08 -0400 From: Holstein Plaza Auctions <[email protected]> Reply-to: Holstein Plaza Auctions <[email protected]> Message-ID: <[email protected]> X-Priority: 3 X-Mailer: PHPMailer 5.1 (phpmailer.sourceforge.net) MIME-Version: 1.0 Content-Transfer-Encoding: 8bit Content-Type: text/plain; charset="iso-8859-1" Content-Length: 195

  Read the article

• apt-get update mdadm scary warnings

  - by user568829

  Just ran an apt-get update on one of my dedicated servers to be left with a relatively scary warning: Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-2.6.26-2-686-bigmem W: mdadm: the array /dev/md/1 with UUID c622dd79:496607cf:c230666b:5103eba0 W: mdadm: is currently active, but it is not listed in mdadm.conf. if W: mdadm: it is needed for boot, then YOUR SYSTEM IS NOW UNBOOTABLE! W: mdadm: please inspect the output of /usr/share/mdadm/mkconf, compare W: mdadm: it to /etc/mdadm/mdadm.conf, and make the necessary changes. W: mdadm: the array /dev/md/2 with UUID 24120323:8c54087c:c230666b:5103eba0 W: mdadm: is currently active, but it is not listed in mdadm.conf. if W: mdadm: it is needed for boot, then YOUR SYSTEM IS NOW UNBOOTABLE! W: mdadm: please inspect the output of /usr/share/mdadm/mkconf, compare W: mdadm: it to /etc/mdadm/mdadm.conf, and make the necessary changes. W: mdadm: the array /dev/md/6 with UUID eef74de5:9267b2a1:c230666b:5103eba0 W: mdadm: is currently active, but it is not listed in mdadm.conf. if W: mdadm: it is needed for boot, then YOUR SYSTEM IS NOW UNBOOTABLE! W: mdadm: please inspect the output of /usr/share/mdadm/mkconf, compare W: mdadm: it to /etc/mdadm/mdadm.conf, and make the necessary changes. W: mdadm: the array /dev/md/5 with UUID 5d45b20c:04d8138f:c230666b:5103eba0 W: mdadm: is currently active, but it is not listed in mdadm.conf. if W: mdadm: it is needed for boot, then YOUR SYSTEM IS NOW UNBOOTABLE! W: mdadm: please inspect the output of /usr/share/mdadm/mkconf, compare W: mdadm: it to /etc/mdadm/mdadm.conf, and make the necessary changes. As instructed I inspected the output of /usr/share/mdadm/mkconf and compared with /etc/mdadm/mdadm.conf and they are quite different. Here is the /etc/mdadm/mdadm.conf contents: # mdadm.conf # # Please refer to mdadm.conf(5) for information about this file. # # by default, scan all partitions (/proc/partitions) for MD superblocks. # alternatively, specify devices to scan, using wildcards if desired. DEVICE partitions # auto-create devices with Debian standard permissions CREATE owner=root group=disk mode=0660 auto=yes # automatically tag new arrays as belonging to the local system HOMEHOST <system> # instruct the monitoring daemon where to send mail alerts MAILADDR root # definitions of existing MD arrays ARRAY /dev/md0 level=raid1 num-devices=2 UUID=b93b0b87:5f7c2c46:0043fca9:4026c400 ARRAY /dev/md1 level=raid1 num-devices=2 UUID=c0fa8842:e214fb1a:fad8a3a2:28f2aabc ARRAY /dev/md2 level=raid1 num-devices=2 UUID=cdc2a9a9:63bbda21:f55e806c:a5371897 ARRAY /dev/md3 level=raid1 num-devices=2 UUID=eca75495:9c9ce18c:d2bac587:f1e79d80 # This file was auto-generated on Wed, 04 Nov 2009 11:32:16 +0100 # by mkconf $Id$ And here is the out put from /usr/share/mdadm/mkconf # mdadm.conf # # Please refer to mdadm.conf(5) for information about this file. # # by default, scan all partitions (/proc/partitions) for MD superblocks. # alternatively, specify devices to scan, using wildcards if desired. DEVICE partitions # auto-create devices with Debian standard permissions CREATE owner=root group=disk mode=0660 auto=yes # automatically tag new arrays as belonging to the local system HOMEHOST <system> # instruct the monitoring daemon where to send mail alerts MAILADDR root # definitions of existing MD arrays ARRAY /dev/md1 UUID=c622dd79:496607cf:c230666b:5103eba0 ARRAY /dev/md2 UUID=24120323:8c54087c:c230666b:5103eba0 ARRAY /dev/md5 UUID=5d45b20c:04d8138f:c230666b:5103eba0 ARRAY /dev/md6 UUID=eef74de5:9267b2a1:c230666b:5103eba0 # This configuration was auto-generated on Sat, 25 Feb 2012 13:10:00 +1030 # by mkconf 3.1.4-1+8efb9d1+squeeze1 As I understand it I need to replace the four lines that start with 'ARRAY' in the /etc/mdadm/mdadm.conf file with the different four 'ARRAY' lines from the /usr/share/mdadm/mkconf output. When I did this and then ran update-initramfs -u there were no more warnings. Is what I have done above correct? I am now terrified of rebooting the server for fear it will not reboot and being a remote dedicated server this would certainly mean downtime and possibly would be expensive to get running again. FOLLOW UP (response to question): the output from mount: /dev/md1 on / type ext3 (rw,usrquota,grpquota) tmpfs on /lib/init/rw type tmpfs (rw,nosuid,mode=0755) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) udev on /dev type tmpfs (rw,mode=0755) tmpfs on /dev/shm type tmpfs (rw,nosuid,nodev) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=620) /dev/md2 on /boot type ext2 (rw) /dev/md5 on /tmp type ext3 (rw) /dev/md6 on /home type ext3 (rw,usrquota,grpquota) mdadm --detail /dev/md0 mdadm: md device /dev/md0 does not appear to be active. mdadm --detail /dev/md1 /dev/md1: Version : 0.90 Creation Time : Sun Aug 14 09:43:08 2011 Raid Level : raid1 Array Size : 31463232 (30.01 GiB 32.22 GB) Used Dev Size : 31463232 (30.01 GiB 32.22 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Sat Feb 25 14:03:47 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : c622dd79:496607cf:c230666b:5103eba0 Events : 0.24 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 17 1 active sync /dev/sdb1 mdadm --detail /dev/md2 /dev/md2: Version : 0.90 Creation Time : Sun Aug 14 09:43:09 2011 Raid Level : raid1 Array Size : 104320 (101.89 MiB 106.82 MB) Used Dev Size : 104320 (101.89 MiB 106.82 MB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Sat Feb 25 13:20:20 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 24120323:8c54087c:c230666b:5103eba0 Events : 0.30 Number Major Minor RaidDevice State 0 8 2 0 active sync /dev/sda2 1 8 18 1 active sync /dev/sdb2 mdadm --detail /dev/md3 mdadm: md device /dev/md3 does not appear to be active. mdadm --detail /dev/md5 /dev/md5: Version : 0.90 Creation Time : Sun Aug 14 09:43:09 2011 Raid Level : raid1 Array Size : 2104448 (2.01 GiB 2.15 GB) Used Dev Size : 2104448 (2.01 GiB 2.15 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 5 Persistence : Superblock is persistent Update Time : Sat Feb 25 14:09:03 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 5d45b20c:04d8138f:c230666b:5103eba0 Events : 0.30 Number Major Minor RaidDevice State 0 8 5 0 active sync /dev/sda5 1 8 21 1 active sync /dev/sdb5 mdadm --detail /dev/md6 /dev/md6: Version : 0.90 Creation Time : Sun Aug 14 09:43:09 2011 Raid Level : raid1 Array Size : 453659456 (432.64 GiB 464.55 GB) Used Dev Size : 453659456 (432.64 GiB 464.55 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 6 Persistence : Superblock is persistent Update Time : Sat Feb 25 14:10:00 2012 State : active Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : eef74de5:9267b2a1:c230666b:5103eba0 Events : 0.31 Number Major Minor RaidDevice State 0 8 6 0 active sync /dev/sda6 1 8 22 1 active sync /dev/sdb6 FOLLOW UP 2 (response to question): Output from /etc/fstab /dev/md1 / ext3 defaults,usrquota,grpquota 1 1 devpts /dev/pts devpts mode=0620,gid=5 0 0 proc /proc proc defaults 0 0 #usbdevfs /proc/bus/usb usbdevfs noauto 0 0 /dev/cdrom /media/cdrom auto ro,noauto,user,exec 0 0 /dev/dvd /media/dvd auto ro,noauto,user,exec 0 0 # # # /dev/md2 /boot ext2 defaults 1 2 /dev/sda3 swap swap pri=42 0 0 /dev/sdb3 swap swap pri=42 0 0 /dev/md5 /tmp ext3 defaults 0 0 /dev/md6 /home ext3 defaults,usrquota,grpquota 1 2

  Read the article

• empty response body in ajax (or 206 Partial Content)

  - by Nikita Rybak

  Hi guys, I'm feeling completely stupid because I've spent two hours solving task which should be very simple and which I solved many times before. But now I'm not even sure in which direction to dig. I fail to fetch static content using ajax from local servers (Apache and Mongrel). I get responses 200 and 206 (depending on the server), empty response text (although Content-Length header is always correct), firebug shows request in red. Javascript is very generic, I'm getting same results even here: http://www.w3schools.com/ajax/tryit.asp?filename=tryajax_first (just change document location to 'http://localhost:3000/whatever') So, it's probably not the cause. Well, now I'm out of ideas. I can also post http headers, if it'll help. Thanks! Response Headers Connection close Date Sat, 01 May 2010 21:05:23 GMT Last-Modified Sun, 18 Apr 2010 19:33:26 GMT Content-Type text/html Content-Length 7466 Request Headers Host localhost:3000 User-Agent Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10.6; en-US; rv:1.9.2.3) Gecko/20100401 Firefox/3.6.3 Accept text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language en-us,en;q=0.5 Accept-Encoding gzip,deflate Accept-Charset ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive 115 Connection keep-alive Referer http://www.w3schools.com/ajax/tryit_view.asp Origin http://www.w3schools.com Response Headers Date Sat, 01 May 2010 21:54:59 GMT Server Apache/2.2.14 (Unix) mod_ssl/2.2.14 OpenSSL/0.9.8l DAV/2 mod_jk/1.2.28 Etag "3d5cbdb-fb4-4819c460d4a40" Accept-Ranges bytes Content-Length 4020 Cache-Control max-age=7200, public, proxy-revalidate Expires Sat, 01 May 2010 23:54:59 GMT Content-Range bytes 0-4019/4020 Keep-Alive timeout=5, max=100 Connection Keep-Alive Content-Type application/javascript Request Headers Host localhost User-Agent Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10.6; en-US; rv:1.9.2.3) Gecko/20100401 Firefox/3.6.3 Accept text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language en-us,en;q=0.5 Accept-Encoding gzip,deflate Accept-Charset ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive 115 Connection keep-alive Origin null

  Read the article

• Java - How to find the redirected url of a url?

  - by Yatendra Goel

  I am accessing web pages through java as follows: URLConnection con = url.openConnection(); But in some cases, a url redirects to another url. So I want to know the url to which the previous url redirected. Below are the header fields that I got as a response: null-->[HTTP/1.1 200 OK] Cache-control-->[public,max-age=3600] last-modified-->[Sat, 17 Apr 2010 13:45:35 GMT] Transfer-Encoding-->[chunked] Date-->[Sat, 17 Apr 2010 13:45:35 GMT] Vary-->[Accept-Encoding] Expires-->[Sat, 17 Apr 2010 14:45:35 GMT] Set-Cookie-->[cl_def_hp=copenhagen; domain=.craigslist.org; path=/; expires=Sun, 17 Apr 2011 13:45:35 GMT, cl_def_lang=en; domain=.craigslist.org; path=/; expires=Sun, 17 Apr 2011 13:45:35 GMT] Connection-->[close] Content-Type-->[text/html; charset=iso-8859-1;] Server-->[Apache] So at present, I am constructing the redirected url from the value of the Set-Cookie header field. In the above case, the redirected url is copenhagen.craigslist.org Is there any standard way through which I can determine which url the particular url is going to redirect. I know that when a url redirects to other url, the server sends an intermediate response containing a header field that tells the url which it is going to redirect but I am not receiving that intermediate response through the url.openConnection(); method.

  Read the article

• Strange numbers in java socket output

  - by user293163

  I have small test app: Socket socket = new Socket("jeck.ru", 80); PrintWriter pw = new PrintWriter(socket.getOutputStream(), false); pw.println("GET /ip/ HTTP/1.1"); pw.println("Host: jeck.ru"); pw.println(); pw.flush(); BufferedReader rd = new BufferedReader(new InputStreamReader(socket.getInputStream())); String str; while ((str = rd.readLine()) != null) { System.out.println(str); } It`s output: HTTP/1.1 200 OK Date: Sat, 13 Mar 2010 22:06:51 GMT Content-Type: text/html;charset=utf-8 Transfer-Encoding: chunked Connection: keep-alive Keep-Alive: timeout=5 Server HTTP/1.1 200 OK Date: Sat, 13 Mar 2010 22:06:51 GMT Content-Type: text/html;charset=utf-8 Transfer-Encoding: chunked Connection: keep-alive Keep-Alive: timeout=5 Server: Apache Cache-Control: max-age=0 Expires: Sat, 13 Mar 2010 22:06:51 GMT 123 <!DOCTYPE html> <html> <head> <meta http-equiv="Content-Type" content="text/html; charset=UTF-8" /> <title>??? IP</title> </head> <body> <div style='text-align: center; font: 32pt Verdana;margin-top: 300px'> ??? IP &#151; 94.103.87.153 </div> </body> </html> 0 Whence these numbers (123 an 0) takes?

  Read the article

• 503 Service Unavailable - What really it means?

  - by pandiya chendur

  Possible Dup: http://stackoverflow.com/questions/2529244/503-service-unavailable-what-really-it-means I am asking on behalf of original question poster because we both work in the same place... I developed a website and it loads in every other system but certainly not in mine ... WHen i used firebug my request show 503 Service Unavailable Firebug response header showed, Server squid/2.6.STABLE21 Date Sat, 27 Mar 2010 12:25:18 GMT Content-Type text/html Content-Length 1163 Expires Sat, 27 Mar 2010 12:25:18 GMT X-Squid-Error ERR_DNS_FAIL 0 X-Cache MISS from xavy X-Cache-Lookup MISS from xavy:3128 Via 1.0 xavy:3128 (squid/2.6.STABLE21) Proxy-Connection close For REF: please visit the original question and look at the answers and comments and help us out..

  Read the article

• Kickstart installation: Unable to read package metadata

  - by yacov

  I'm trying to install a CentOS OS with kickstart using HTTP as the installation source. The kickstart server and the installed server are both running on VMs on the same machine. after the anaconda system installer starts it fails with the following message: I tried installing two different versions of Centos(5.5 and 5.2), and they both pass a CDROM media test the manual installation provides. The only errors on the kickstart server side are some errors in the httpd log I consider irrelevant: [Sat Mar 12 23:25:19 2011] [error] [client 192.168.1.112] File does not exist: /tftpboot/linux-install/platforms/CentOS5.5/images/product.img [Sat Mar 12 23:25:19 2011] [error] [client 192.168.1.112] File does not exist: /tftpboot/linux-install/platforms/CentOS5.5/disc1 I tried searching the internet for days and haven't found any solution... Does anyone have any idea?

  Read the article

• Apache error_log repeated attempts to access forum.php

  - by bMon

  About every two seconds I am getting: [Sat Feb 19 19:00:01 2011] [error] [client 69.239.204.217] script '/var/www /html/forum.php' not found or unable to stat [Sat Feb 19 19:00:04 2011] [error] [client 69.239.204.217] File does not exist: /var/www/html/404.shtml ..in my /var/log/httpd/error_log file. Sometimes the request will be for forum_asp.php. I'm assuming its a bot trying to access insecure forum files, but I'm not so sure since it appears each is a unique IP and not just a few rouge IPs hitting it consecutively. And whois results of the ip's aren't all the classic ISP in Russia or China, they are more end user address (comcast, etc). Any insight into whats going on here would be appreciated. Also, any techniques people use to do a "live monitor" of web traffic would be appreciated. Right now I'm doing a: tail -f error_log Thanks.

  Read the article

• Graphite SQLite3 DatabaseError: attempt to write a readonly database

  - by Anadi Misra

  Running graphite under apache httpd, with slqite database, I have the correct folder permissions [root@liaan55 httpd]# ls -ltr /var/lib | grep graphite drwxr-xr-x. 2 apache apache 4096 Aug 23 19:36 graphite-web and [root@liaan55 httpd]# ls -ltr /var/lib/graphite-web/ total 68 -rw-r--r--. 1 apache apache 65536 Aug 23 19:46 graphite.db syncdb also seems to have gone fine [root@liaan55 httpd]# sudo -su apache bash-4.1$ whoami apache bash-4.1$ python /usr/lib/python2.6/site-packages/graphite/manage.py syncdb /usr/lib/python2.6/site-packages/graphite/settings.py:231: UserWarning: SECRET_KEY is set to an unsafe default. This should be set in local_settings.py for better security warn('SECRET_KEY is set to an unsafe default. This should be set in local_settings.py for better security') /usr/lib/python2.6/site-packages/django/conf/__init__.py:75: DeprecationWarning: The ADMIN_MEDIA_PREFIX setting has been removed; use STATIC_URL instead. "use STATIC_URL instead.", DeprecationWarning) /usr/lib/python2.6/site-packages/django/core/cache/__init__.py:82: DeprecationWarning: settings.CACHE_* is deprecated; use settings.CACHES instead. DeprecationWarning Creating tables ... Creating table account_profile Creating table account_variable Creating table account_view Creating table account_window Creating table account_mygraph Creating table dashboard_dashboard_owners Creating table dashboard_dashboard Creating table events_event Creating table auth_permission Creating table auth_group_permissions Creating table auth_group Creating table auth_user_user_permissions Creating table auth_user_groups Creating table auth_user Creating table django_session Creating table django_admin_log Creating table django_content_type Creating table tagging_tag Creating table tagging_taggeditem You just installed Django's auth system, which means you don't have any superusers defined. Would you like to create one now? (yes/no): yes Username (leave blank to use 'apache'): root E-mail address: [email protected] Password: Password (again): Superuser created successfully. Installing custom SQL ... Installing indexes ... Installed 0 object(s) from 0 fixture(s) bash-4.1$ exit and the local-settings.py file is as follows STORAGE_DIR = '/var/lib/graphite-web' INDEX_FILE = '/var/lib/graphite-web/index' DATABASES = { 'default': { 'NAME': '/var/lib/graphite-web/graphite.db', 'ENGINE': 'django.db.backends.sqlite3', 'USER': '', 'PASSWORD': '', 'HOST': '', 'PORT': '' } } I still get this error [Sat Aug 23 19:47:17 2014] [error] [client 10.42.33.238] File "/usr/lib/python2.6/site-packages/django/db/backends/sqlite3/base.py", line 344, in execute [Sat Aug 23 19:47:17 2014] [error] [client 10.42.33.238] return Database.Cursor.execute(self, query, params) [Sat Aug 23 19:47:17 2014] [error] [client 10.42.33.238] DatabaseError: attempt to write a readonly database not sure what is missing in this configuration

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >