Search Results

Search found 1565 results on 63 pages for 'can bus'.

Page 40/63 | < Previous Page | 36 37 38 39 40 41 42 43 44 45 46 47  | Next Page >

• Why does my Mac always crash when I enable `ask for password after screensaver ended`?

  - by Koning Baard XIV

  I have enabled these two things: Placing the mouse-pointer in the bottom-left corner of any display makes the screensaver appear After the screensaver or stand-by has ended, ask for password However, this combination always leads to this (Black Screen of Death) after entering the screensaver with the bottom-left corner: Here are my system specs: Hardware Overview: Model Name: iMac Model Identifier: iMac9,1 Processor Name: Intel Core 2 Duo Processor Speed: 2,66 GHz Number Of Processors: 1 Total Number Of Cores: 2 L2 Cache: 6 MB Memory: 2 GB Bus Speed: 1,07 GHz Boot ROM Version: IM91.008D.B08 SMC Version (system): 1.44f0 Serial Number (system): W89171JF0TF Hardware UUID: 323A90F0-8A2F-5057-B501-2087489E0DFF System Software Overview: System Version: Mac OS X 10.6.3 (10D573) Kernel Version: Darwin 10.3.0 Boot Volume: Macintosh HD Boot Mode: Normal Computer Name: YOU SHOULD NOT KNOW THIS User Name: YOU SHOULD NOT KNOW THIS Secure Virtual Memory: Not Enabled 64-bit Kernel and Extensions: No Time since boot: 11:46 Can anyone help me? Thanks

  Read the article

• Ubuntu, No wireless networks found after correctly installed madwifi

  - by Peter

  Hi, I just installed madwifi on my MSI laptop with an Atheros AR5001 wifi card & Lucid. As far as I can see and according to System - Administration - Hardware drivers the install was successful and the card + driver is up and running. However, I don't see any wireless network (my windows PC can see about 5 wireless networks). I tried it with the network manager applet as well as with wicd. If I try to connect to "Hidden Wireless Network" via nm-applet, it will start to connect for a while but is unable too (although I supply it with the correct WEP settings & key) So, I'm unable to use my wireless network. What am i doing wrong? Some information about my system: iwconfig lo no wireless extensions. eth0 no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11g ESSID:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:17 dBm Sensitivity=1/1 Retry:off RTS thr:off Fragment thr:off Power Management:off Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 pan0 no wireless extensions. ifconfig ath0 Link encap:Ethernet HWaddr 00:15:af:cf:e2:ca inet6 addr: fe80::215:afff:fecf:e2ca/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 00:21:85:4d:82:78 inet addr:192.168.2.101 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::221:85ff:fe4d:8278/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3800 errors:0 dropped:0 overruns:0 frame:0 TX packets:2944 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3940261 (3.9 MB) TX bytes:525218 (525.2 KB) Interrupt:27 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) wifi0 Link encap:UNSPEC HWaddr 00-15-AF-CF-E2-CA-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3497 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:280 RX bytes:0 (0.0 B) TX bytes:179947 (179.9 KB) Interrupt:16 lshw -C network *-network description: Wireless interface product: AR5001 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wifi0 version: 01 serial: 00:15:af:cf:e2:ca width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath_pci latency=0 multicast=yes wireless=IEEE 802.11g resources: irq:16 memory:fd7f0000-fd7fffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 01 serial: 00:21:85:4d:82:78 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.2.101 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:27 ioport:c800(size=256) memory:fe2ff000-fe2fffff memory:fe2c0000-fe2dffff(prefetchable) lspci 00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx) 00:04.0 PCI bridge: ATI Technologies Inc Device 7914 00:06.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 2) 00:07.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (PCI Express Port 3) 00:12.0 SATA controller: ATI Technologies Inc SB600 Non-Raid-5 SATA 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 VGA compatible controller: ATI Technologies Inc RS690M [Radeon X1200 Series] 01:05.2 Audio device: ATI Technologies Inc Radeon X1200 Series Audio Controller 02:00.0 Ethernet controller: Atheros Communications Inc. AR5001 Wireless Network Adapter (rev 01) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01) 06:04.0 CardBus bridge: O2 Micro, Inc. OZ711MP1/MS1 MemoryCardBus Controller (rev 21) 06:04.2 SD Host controller: O2 Micro, Inc. Integrated MMC/SD Controller (rev 01) 06:04.3 Bridge: O2 Micro, Inc. Integrated MS/xD Controller (rev 01) 06:04.4 FireWire (IEEE 1394): O2 Micro, Inc. Firewire (IEEE 1394) (rev 02) less /proc/modules | grep ath ath_rate_sample 11476 1 - Live 0xf812b000 ath_pci 193197 0 - Live 0xf85c3000 wlan 222892 5 wlan_wep,wlan_scan_sta,ath_rate_sample,ath_pci, Live 0xf8537000 ath_hal 398604 3 ath_rate_sample,ath_pci, Live 0xf8480000 I've been at this for hours now, also tried ndiswrapper and ath5k drivers with no luck, and really could use some help. Cheers.

  Read the article

• Unable to create context rendering error whet run OpenGL application

  - by Rodnower

  Hello, I try to run Mesa gears example and I get following error: freeglut (./gears): Unable to create direct context rendering for window 'Gears' This may hurt performance. though the application runs successfully, but I guess that in future I will have much problems with productivity. I run Linux CentOS 5 on WMvare 7. Mesa's version is 6.5 Relevant output of lspci -v gives: 00:0f.0 VGA compatible controller: VMware SVGA II Adapter (prog-if 00 [VGA controller]) Subsystem: VMware SVGA II Adapter Flags: bus master, medium devsel, latency 64, IRQ 9 I/O ports at 10d0 [size=16] Memory at d0000000 (32-bit, non-prefetchable) [size=128M] Memory at d8000000 (32-bit, non-prefetchable) [size=8M] [virtual] Expansion ROM at 30000000 [disabled] [size=32K] Capabilities: [40] Vendor Specific Information Any one have idea? There is driver of vmvare for CentOS? Thank you for ahead.

  Read the article

• How to install audio drivers for Acer Revo nettop?

  - by CT

  I have a Acer Revo nettop. I wiped the XP Home install that came on the machine and put XP Pro on. Acer's support website would lead you to believe that this product does not exist. I know it has a NVIDIA ION LE chipset so I headed over to nvidia.com to download drivers. Ive downloaded and installed the Chipset drivers, Graphics Drivers, and HDMI audio drivers. I have no sound. Under Device Manager there is an unknown Audio Device on High Definition Audio Bus. I do not have an HDMI cable to test hdmi audio. I would just like the standard audio mini-jack output to work. Anyone know of the correct driver or a generic driver that would work? Thanks

  Read the article

• Linux Logitech QuickCam Pro 9000 - microphone issues

  - by drahnr

  I got a Logitech Quickcam Pro 9000, the cam itself is working as it honors the UVC spec. This fancy WebCam has a integrated mic which worked some time before but now, it does no more. (Note: I use pulseaudio as it is a USB Mic and I am not really keen on the hassle of ALSA setup) Things I check already are if it gets detected at all: $ lsusb |grep Logi Bus 002 Device 002: ID 046d:0809 Logitech, Inc. Webcam Pro 9000 is muted in alsa-mixer - not the case, volume at 100 pavucontrol shows it too, but no input level bar! On top of that, if I open the gnome3 (fallback mode) audio panel(from the desktop panel), and disabel/reenable it in the hardware tab, it works "for some time"... Any hints? Any ideas? I am really out options for now, and the fact it worked like 6 months ago (perfectly) makes it no better.

  Read the article

• Processor not running at max speed

  - by Andrew Hampton

  My laptop has an Intel Core 2 Duo T9300 which should be running at 2.5GHz, however CPU-Z consistently reports my Core speed at right under 1.6Ghz (8x multiplier and ~200MHz Bus Speed). Even when I'm doing heavy development work and the processor is running at 100% for extended periods of time the core speed reported by CPU-Z never goes up to 2.5GHz. My understanding is that this reduction in speed is to save power, but this happens even when I'm plugged into the outlet. Does anyone know why this is happening or how to fix it?

  Read the article

• Force an LXC container to use its own IP address

  - by emma sculateur

  Sorry if this question has already been asked. I could not find it, I have this setup : +---------------------------------------------------------------------------------------------+ |HOST | | | | +-------------------------------------------------+ | | | UBUNTU-VM | | | | | | | | +-------------------+ | | | | |UBUNTU-LXC | | +------------------+ | | | | 10.0.0.3/24 | 10.0.0.1/24 | |OTHER VM | | | | | eth0-----lxcbr0----------eth0-----------br0----------eth0 | | | | | | 192.168.100.2/24| 192.168.100.1/24 |192.168.100.3/24 | | | | +-------------------+ | +------------------+ | | +-------------------------------------------------+ | +---------------------------------------------------------------------------------------------+ When I ping 192.168.100.3 from my UBUNTU-LXC, the source IP address is automatically changed to 192.168.100.2 by UBUNTU-VM. It's like having a NAT, whereas I really want my UBUNTU-LXC to talk with it own IP address. Is there any way to do this ? Edit : these info may be relevant : I am using KVM +libvirt to set up my VMs Here is how I create my interface in UBUNTU-VM : <interface type='bridge'> <mac address='52:54:00:cb:aa:74'/> <source bridge='br0'/> <model type='e1000'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x09' function='0x0'/> </interface>

  Read the article

• Can not boot CentOS VM using VirtIO in KVM

  - by Jake

  I converted qcow2 image to raw and changed I/O bus to VirtIO for a VM. now I can't boot that VM. I Installed VirtIO driver with following command: mkinitrd --with virtio_pci --with virtio_blk -f /boot/initrd-$(uname -r).img $(uname -r) and these are related kernel modules: virtio_balloon 11329 0 virtio_blk 11593 3 virtio_pci 11845 0 virtio_ring 8513 1 virtio_pci virtio 9541 3 virtio_balloon,virtio_blk,virtio_pci and this is what happens during boot-up. I also changed /boot/grub/device.map from "(hd0) /dev/sda" to "(hd0) /dev/vda" but problem still exists. any ideas how to fix this ? This is my default option to boot: title CentOS (2.6.18-308.13.1.el5) root (hd0,0) kernel /vmlinuz-2.6.18-308.13.1.el5 ro root=/dev/VolGroup00/LogVol00 initrd /initrd-2.6.18-308.13.1.el5.img

  Read the article

• USB driver problems (Windows 8.1)

  - by HelloWorld

  Every time I turn on my laptop the USB ports don't work and the drivers have an error. In order to fix this I'm forced to start the Device Manager, uninstall all the USB drivers, open the Control Panel, click Find and fix problems (under System and Security), click Configure a device (under Hardware and Sound) and then when that window pops up just hit Next until I can see my USB drivers reinstalled and working in the Device Manager window under Universal Serial Bus controllers. I found this way to fix it but I would like a permanent solution so that I don't have to do this every time I turn on the machine. Any ideas? When I bought the machine it had Window 7 installed but I later upgraded it to Windows 8.0 and then 8.1 after that.

  Read the article

• How to use Ralink RT2501/RT2573 as wifi access point in Debian Linux

  - by user60813

  Hi, I have a fit-PC server with Debian GNU/Linux (Lenny). I would like to use it as a wifi access point since my Linksys WRT54GS has become unstable. I have a USB Ralink wifi NIC. When I insert the card to USB I can see this with lsusb: Bus 001 Device 002: ID 148f:2573 Ralink Technology, Corp. RT2501/RT2573 Wireless Adapter I have tried following various HOWTOs on using wifi card as AP in Linux, however, it seems that the card cannot go into monitor mode. I believe this is because I must use a newer driver or upload non-free firmware or something like that. I have tried installed wicd, but it does not help. I bought this wifi adapter because I was told that it is one of the most common used Linux supported wifi cards that can be used as access point and a lot of other stuff. So my question is: How do I set up this USB wifi card as wireless access point in Debian Lenny?

  Read the article

• Can I use dmraid instead of md (mdadm) to make software RAID-1 and RAID-1+0 volumes?

  - by Don MacAskill

  On a related question about SSDs and TRIM (see: Possible to get SSD TRIM (discard) working on ext4 + LVM + software RAID in Linux? ), it turns out that dmraid may now (or shortly) support TRIM on RAID-1. Typically, we've used md (via mdadm) to create our RAID-1 volumes, then used LVM to create volume groups, then formatted with the file system of our choice (ext4 lately). We've been doing this for years, and Google & ServerFault searches seem to confirm this is the most common way of doing software RAID with volume management. Google searches seem to suggest that dmraid is use for so-called 'fakeRAID' configurations where there's some level of hardware 'help' in the form of RAID BIOS in the controller, which we don't have (and don't want to use - we'd like a fully software solution). Since we'd like to use TRIM on our SSDs, and since md doesn't seem to (yet?) support TRIM, I'm wondering if it's possible to use dmraid instead of md to create RAID-1 (and RAID-1+0) volumes in software, with no hardware support (ie, just plugged into a dumb SATA/SAS bus)?

  Read the article

• when i set my FSB to 400mhz in bios it actually stays at 333mhz

  - by Mantis

  My front side bus (FSB) is rated for a maximum of 400mhz (Rated FSB 1600MHz). In fact, it used to run at 400mhz until recently. I'm trying to overclock my E8400 to 3.6GHz. I have done that in the past by having the FSB at 400 with a multiplier of 9. Now, when I set the FSB to 400, the system boots as normal, but the FSB stubbornly is stuck at 333 (Rated FSB 1333). The CMOS is set to 400, I've triple-checked it. It's just the FSB isn't listening. Is my FSB damaged? Gigabyte mobo

  Read the article

• System says memory controller not available and doesn't boot?

  - by Martin

  Hello everybody, Recently I have had a MainBoard-problem. I've send my mainboard to service and today I got it back from the company. It is a Foxconn 520a mainboard. Now I have installed my exchanged mainboard. But now I have a problem. My system boots until the device list with IRQ entries appear. The system says "Verifying DMI-pool-data..." and nothing happens. The IRQ-device list shows that the memory-controller is not available. All other devices have got an IRQ. Bus No. Device No. Func No. Vendor/Device Class Device Class IRQ 0 0 0 10DE 0547 0500 Memory Controller NA Do you have any ideas where the problem could be? I already have disconnected all unnecessary devices like the hard disks. Perhaps it is a BIOS problem, but I don't know where I should look. Would be nice if there is any advice, Greetings, Martin

  Read the article

• 912 stream processor available in OpenCL

  - by tugrul büyükisik

  I am thinking of assembling this system: AMD CPU (A8-3870 APU which has Radeon HD 6550D inside: 400 stream processors:xxx GFLOPS) nearly 110$ AMD Graphics card: HD 7750 (512 stream processors:819 GFLOPS peak performance) nearly 170$ Appropriate ram (1600MHz bus) Mainboard What GFLOPS level can I reach as a stable mode with using OpenCL and similar programs? Can I use all 912 stream processors at the same time? I am not trying to do a VS question. I need to know what could be better for scientific computing (%75 of the time) and gaming (%25 of the time) because I have a low budget. With "scientific calculations" I mean fluid dynamics/solid state physics simulating; with games I mean those that need openCL and PhysX.

  Read the article

• Brand New MOnitor Won't Get Input From CPU

  - by HollerTrain

  I have an old Dell 2350. I found a HD a few months ago and plugged it in and it booted up. So I just purchased a monitor and plugged it in, and put the HD inside and connected the two connections (Bus, and a four pronged connector) and no signal is being sent to monitor. is this a monitor issue or the HD is just dead? HD is spinning. CPU is turned on :) Yet no signal.. any thoughts?

  Read the article

• upgrading my computer system for office use

  - by denise ellul

  Presently I have the under-mentioned computer system. What should be changed and upgraded with the following products that I own presently? I am interested in performance issues related to cache memory, bus speed, RAM, CAS latency as well as other considerations. Thanks for your help. Processor (CPU): Intel Celeron Dual Core E3300 2.5 GHz Motherboard: Asus P5QPL-AM G41 Main Memory (RAM): 2 GB Team Elite DDR2 PC8000 Case: Coolermaster RC330 Power Supply Unit: 500W EZ-Cool Standard Storage Device (Hard Drive): 500GB Samsung Video Card: Intel GMA X4500 (On-board) Optical Drive: LG GH22NS50 Sound Card: AC 97 (On – board) Card Reader: Akasa Black TFT Monitor: 19” View Sonic Speakers: Logitech S120 2.0

  Read the article

• Logitech M185 Wirless Mouse issue

  - by Elliot Harrison

  An issue with a Logitech M185 mouse today. A user is unable to use the device. The device works perfectly fine on my PC (It appears as HID-compliant mouse), but not on her laptop. It does not appear in her device manager on the 'Mice and other pointing devices' section. I did notice an unknown device in the Universal Serial Bus Controllers section, but when I try to update the driver, it says it has the most up to date driver. We've tried plugging in the dongle in multiple USB slots but no luck. Any advice? It's a HP 620 Laptop on Windows 7. Thank you :)

  Read the article

• Is an Ethernet point to point connection without a switch real time capable?

  - by funksoulbrother

  In automation and control, it is commonly stated that ethernet can't be used as a bus because it is not real time capable due to packet collisions. If important control packets collide, they often can't keep the hard real time conditions needed for control. But what if I have a single point to point connection with Ethernet, no switch in between? To be more precise, I have an FPGA board with a giga-Ethernet port that is connected directly to my control PC. I think the benefits of giga Ethernet over CAN or USB for a p2p connection are huge, especially for high sampling rates and lots of data generation on the FPGA board. Am I correct that with a point to point connection there can't be any packet collisions and therefore a real time environment is given even with ethernet? Thanks in advance! ~fsb

  Read the article

• Should USB controller drivers be updated?

  - by Coldblackice

  Should USB controller drivers be updated? In Windows 7, many of the core system devices/buses/controllers still use stock Microsoft drivers dating back to 2006 -- things such as USB controllers and the PCI bus (and subsequent devices in the tree). Should these be getting updated? I would think that surely there would have been improvements/fixes/updates to some or any of these drivers by now, now over 7 years old. Does Windows know "best" in this case, updating these respective drivers when it's needed, or should the user be keeping an eye out for drivers in this "vein" of devices (meaning integrated/core/non-pluggable system devices that are built into the motherboard)?

  Read the article

• if there are multiple kernel module can drive the same device, what is the rule to choose from them?

  - by Dyno Fu

  both pcnet32 and vmxnet can drive the device. $ lspci -k ... 02:01.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] (rev 10) Subsystem: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] Flags: bus master, medium devsel, latency 64, IRQ 19 I/O ports at 2000 [size=128] [virtual] Expansion ROM at dc400000 [disabled] [size=64K] Kernel driver in use: vmxnet Kernel modules: vmxnet, pcnet32 both kernel modules are loaded, $ lsmod | grep net pcnet32 32644 0 vmxnet 17696 0 mii 5212 1 pcnet32 as you see, kernel driver in use is vmxnet. is there any policy/algorithm in kernel how to choose from the candidates?

  Read the article

• MD3200i Slow Performance and Queue Depth

  - by Caleb_S

  Read performance on our SAN is slow under certain workloads. When we compare this to some local storage, we find the local storage performing 2x as fast. The SAN performs well with a high Queue Depth, and poorly with a low queue depth. However, the local storage performs well with a low Queue Depth. I'd like to know the reason for this occurring and find out what the specific limiting factor is in this situation. MD3200i iSCSI SAN ($15,000) 6 x 600GB 15k SAS RAID5 6 x 2TB 7.2k NLS RAID5 XCOPY /j Benchmark: (Slow) 15k Array - 71MB/s (Queue Depth 1) 7.2k Array- 71MB/s (Queue Depth 1) Robycopy /MT:32 Benchmark: (Fast) 15k Array - 171MB/s (Queue Depth ~12) 7.2k Array- 128MB/s (Queue Depth ~12) , , Read Performance on a Local controller is fast under the workload the SAN is slow at. , HighPoint 2230 RAID Controller ($600) 4 x 1TB 7.2k SATA RAID5 XCOPY /j Benchmark: 7.2k Array - 145MB/s (Queue Depth 1) (appears to max out the SATA bus)

  Read the article

• How to tell if OpenGL is really working in Ubuntu 10.04

  - by Jonathan

  I have a lenovo S9e running Intel integrated graphics. Here is my lspci output related to the graphics: 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) Subsystem: Lenovo Device 3870 Flags: bus master, fast devsel, latency 0 Memory at f0580000 (32-bit, non-prefetchable) [size=512K] Capabilities: [d0] Power Management version 2 I want to know how I can make sure OpenGL support is running in full on an Ubuntu 10.04 installation. I have a few hints to think that it is not: The "Desktop Effects" will not load Apps such as stardock, when attempting to use OpenGL rendering, will display black boxes instead of transparency In the games Pioneers, the number-tile icons are suspiciously just black circles Windows games running with Wine will only support software rendering, not hardware rendering When I boot into a Knoppix LiveCD, the desktop effects do work, splendidly, meaning compiz detects my computer as capable. My problem with troubleshooting is that Canonical has basically eliminated the conf-file-based mechanism of X11 as far as I can tell, thus making it even harder to ensure graphics modules are loading properly. How do I debug and test OpenGL on m Ubuntu 10.04 installation?

  Read the article

• ata error: UnrecovData Handshk

  - by Aaron Digulla

  I just saw this message in my log (openSUSE 11.3, Linux 2.6.36.2): ata6.00: exception Emask 0x10 SAct 0x1 SErr 0x400100 action 0x6 frozen ata6.00: irq_stat 0x08000000, interface fatal error ata6: SError: { UnrecovData Handshk } ata6.00: failed command: WRITE FPDMA QUEUED ata6.00: cmd 61/58:00:9f:69:00/00:00:00:00:00/40 tag 0 ncq 45056 out res 40/00:04:9f:69:00/00:00:00:00:00/40 Emask 0x10 (ATA bus error) ata6.00: status: { DRDY } ata6: hard resetting link ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata6.00: configured for UDMA/133 ata6: EH complete Two questions: Which disk caused the error? I search /sys and /proc but couldn't find a way to map ata6 to a device (/dev/sdaXY) When such an error happens, does Linux retry the disk operation? Or do I have a corrupt filesystem?

  Read the article

• Brand New Monitor Won't Get Input From Computer

  - by HollerTrain

  I have an old Dell 2350. I found a HD a few months ago and plugged it in and it booted up. So I just purchased a monitor and plugged it in, and put the HD inside and connected the two connections (Bus, and a four pronged connector) and no signal is being sent to monitor. is this a monitor issue or the HD is just dead? HD is spinning. CPU is turned on :) Yet no signal.. any thoughts?

  Read the article

• ARM Debian (squeeze) USB driver with mismatch 3.3.3 kernel but /lib/modules/2.6.36

  - by frank

  Hei guys, my sheevaplug embedded server works fine, but when I wanted to use USB, the device gets not attached to /dev/tty/USB0 lsusb shows correctly: Bus 001 Device 002: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port an modprobe usbserial raises: FATAL: Could not load /lib/modules/3.3.3/modules.dep: No such file or directory in the /lib/modules/ Folder there is instead a 2.6.36-Folder uname -r gives 3.3.3 How can I overcome this mismatch? Can I create a symlink? I can't flash this embedded device since it is deployed somewhere, only ssh? Please advise!

  Read the article

< Previous Page | 36 37 38 39 40 41 42 43 44 45 46 47  | Next Page >