Search Results

Search found 3324 results on 133 pages for 'gb'.

Page 40/133 | < Previous Page | 36 37 38 39 40 41 42 43 44 45 46 47  | Next Page >

• Installation Problems & Antivirus

  - by Sagar Walvekar

  We have just migrated our systems from Windows to Ubuntu. We have more than 50 systems previously running Windows XP & Windows 7. After the release of 12.04 we decided to switch to Ubuntu. While we were installing Ubuntu 12.04 on Pentium 4 systems we have faced some issues. We tried it with a USB flash driver & CD. The typical configuration of the system is as follows: Pentium 4 with HT & 512 MB RAM, 40/80 GB IDE / SATA HDD. In windows there were several partitions and data on all the drives in all the systems. We have addressed this by taking backup of the C: drive on other drives & while installing Ubuntu we have just deleted & the C drive & recreated Linux partitions as follows - /root , /Boot, /Home & Swap.(in 10 GB) The problem is that the Linux gets installed without any error. However when I restart the system after the installation the system hangs in while detecting the HDD in BIOS and the system fails to start until I remove the HDD. When I installed the previous Ubuntu version it worked fine, without any hassle. Also if we install Ubuntu 12.04 on same HDD on any other higher capacity system & reconnected to old system it works fine. How can I fix this problem? Also, is there is any Antivirus which will give me real time protection on ubuntu 11 & higher versions with both 32 & 64 Bits?

  Read the article

• Missing Operating System after trying to upgrade to Ubuntu 11

  - by Mauricio

  there! After trying to upgrade from Ubuntu 10.04 to 11, the upgrading process stopped when running and then I got an "out of disk, grub rescue" message when booting. After running Boot Repair, I got this results. Now I get "Missing Operating System" whent trying to boot. Bellow I show some results from some commands I gather from help foruns, but I still reached no solution. Could you please help me? Any enlightment will be very helpful! Disk Utility says "Disk has a few bad sectors". When trying to run the Self-test I get "FAILED (Read)" Here we have what Gparted says about the /dev/sda1 partition (ext4): Flags: boot Status: not mounted Warning: e2label: Attempt to read block from filesystem resulted in short read while trying to open /dev/sda1Couldn`t find valid filesystem superblockUnable to read the contents of this filesystem! From sudo fdisk -lI got: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectorsUnits = sectors of 1 * 512 = 512 bytesSector size (logical/physical): 512 bytes / 512 bytesI/O size (minimum/optimal): 512 bytes / 512 bytesDisk identifier: 0x000e0596 Device Boot Start End Blocks Id System/dev/sda1 * 2048 607428607 303713280 83 Linux/dev/sda2 607430654 625141759 8855553 5 Extended/dev/sda5 607430656 625141759 8855552 82 Linux swap / SolarisDisk /dev/sdb: 320.1 GB, 320072933376 bytes255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectorsUnits = sectors of 1 * 512 = 512 bytesSector size (logical/physical): 512 bytes / 512 bytesI/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000c3c41 Device Boot Start End Blocks Id System /dev/sdb1 * 63 625137344 312568641 c W95 FAT32 (LBA) " and fromsudo fdisk /dev/sda1I got fdisk: unable to read /dev/sda1: Inappropriate ioctl for device` From sudo mount /dev/sda1 /mntI got: mount: wrong fs type, bad option, bad superblock on /dev/sda1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so From sudo update-grubI got: error: cannot read from `/dev/sda'. /usr/sbin/grub-probe: error: cannot find a device for / (is /dev mounted?).

  Read the article

• VirtualBox : increase hard disk size of the virtual machine

  - by wim

  I have run out of space on my WinXP virtual machine, which I only gave 10 GB space for when I created it. Is there an easy way to increase it to, say, 20 GB? I can't see any obvious option in VirtualBox settings. edit: the suggestion below gives this error wim@wim-ubuntu:/media/data/winxp_vm$ VBoxManage modifyhd wim.vdi --resize 20000 VBoxManage: error: Cannot register the hard disk '/media/data/winxp_vm/wim.vdi' {46284957-2c09-4e70-8a49-bfbe0f7f681d} because a hard disk '/home/wim/VirtualBox VMs/winxp_vm/wim.vdi' with UUID {46284957-2c09-4e70-8a49-bfbe0f7f681d} already exists VBoxManage: error: Details: code NS_ERROR_INVALID_ARG (0x80070057), component VirtualBox, interface IVirtualBox, callee nsISupports Context: "OpenMedium(Bstr(pszFilenameOrUuid).raw(), enmDevType, AccessMode_ReadWrite, fForceNewUuidOnOpen, pMedium.asOutParam())" at line 210 of file VBoxManageDisk.cpp edit2: removing the .vdi from VirtualBox before calling VBoxManage command, then adding it back in, was successful. But now I can't boot the virtual machine, I get this worrying screen: By the way, it says FATAL: Could not read from the boot medium! System halted. edit3: The vdi must be reattached to the VM after VBoxManage command. Further, the partition will need to be resized from WITHIN windows, because you will have this empty space: I was able to resize the partition easily using a bit of freeware called EASEUS Partition Master 9.1.0 Home Edition.

  Read the article

• I have a ESXi 5.0 installed and when I am Installing Ubuntu Server 12.04 LTS it is giving an error saying grub installation failed?

  - by Rishee

  I have a ESXi 5.0 installed and when I am Installing Ubuntu Server 12.04 LTS (32 bit) it is giving an error saying grub installation failed? Please check the below screenshot of the error. I have other Ubuntu servers running fine on this esxi server, so I don't think problem is with ESXi. I have 32 GB of ram spare on this ESXi and have given 2 GB of RAM to this 12.0 LTS VM. I have given 2 cores of processor. I have tried supplying different ISO Image to this VM as I thought the 1st image that I downloaded has errors.. But defiantly that's not the case as all 3 different ISO images that I downloaded of Ubuntu server 12.04 LTS (32-bit) can't be corrupt!! Just to make sure that the Image does not have problem I used that Image to install it for testing on stand alone system. it works fine there!! This is a production ESXi server with which I can't play with, how ever I can play whith the Ubuntu Server 12.04 LTS (32-Bit) VM that we have created on that ESXi. I need help on this as soon as possible. go live date of this server is really close. (This Question is already there on Super user and Server Fault.)

  Read the article

• Ubuntu installation does not recognize drive partitioning

  - by Woltan

  I have a 1TB drive and installed Windows 7 on a 128GB partition. When I now try to install Ubuntu 11.04 it does not recognize the Windows partition but offers the complete 1TB drive to install Ubuntu on instead. It displays: However, in the Ubuntu Disk Utility the Windows partitions are recognized. What do I need to do in order for Ubuntu to recognize the Windows 7 partition and install Ubuntu as a dual boot? Response to comments The following commands were executed and the results are shown below: fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x34a38165 Device Boot Start End Blocks Id System /dev/sda1 * 1 13 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 13 16318 130969600 7 HPFS/NTFS Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x14a714a6 Device Boot Start End Blocks Id System /dev/sdb1 1 60801 488384001 83 Linux parted -l Warning: Unable to open /dev/sr0 read-write (Read-only file system). /dev/sr0 has been opened read-only. Error: /dev/sr0: unrecognised disk label

  Read the article

• How to mount an external HDD?

  - by Slash

  I have Ubuntu Linux 12.04 version the latest right now.I want to mount an external HDD NTFS 1TB.I have followed many guides but still no success.The error I'm getting is this: Failed to read last sector (1953523119): Invalid argument HINTS: Either the volume is a RAID/LDM but it wasn't setup yet, or it was not setup correctly (e.g. by not using mdadm --build ...), or a wrong device is tried to be mounted, or the partition table is corrupt (partition is smaller than NTFS), or the NTFS boot sector is corrupt (NTFS size is not valid). Failed to mount '/dev/sdb1': Invalid argument The device '/dev/sdb1' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? Using Storage Device MAnager i get this error:Error mounting: mount exited with exit code 1: helper failed with: mount: only root can mount /dev/sdb1 on /media/Skliros_Diskos {external disk name} When I use sudo fdisk -l, this is the output: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e0bc6 Device Boot Start End Blocks Id System /dev/sda1 * 2048 618854399 309426176 83 Linux /dev/sda2 618856446 625141759 3142657 5 Extended /dev/sda5 618856448 625141759 3142656 82 Linux swap / Solaris Disk /dev/sdb: 1000.2 GB, 1000202043392 bytes 255 heads, 63 sectors/track, 121600 cylinders, total 1953519616 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0002093a Device Boot Start End Blocks Id System /dev/sdb1 2048 1953525167 976761560 7 HPFS/NTFS/exFAT

  Read the article

• I can't install Ubuntu on my Dell Inspiron 15R at all

  - by Kieran Rimmer

  I'm attempting to install Ubuntu 12.04LTS, 64 bit onto a Dell Inspiron 15R laptop. I've shrunk down one of the windows partitions and even used gparted to format the vacant space as ext4. However, the install disk simply does not present any options when it comes to the partitioning step. What I get is a non-responsive blank table As well as the above, I've changed the BIOS settings so that USB emulation is disabled (as per Can't install on Dell Inspiron 15R), and changed the SATA Operation setting to all three possible options. Anyway, the install CD will bring up the trial version of ubuntu, and if I open terminal and type sudo fdisk -l, I get this: Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xb4fd9215 Device Boot Start End Blocks Id System /dev/sda1 63 80324 40131 de Dell Utility Partition 1 does not start on physical sector boundary. /dev/sda2 * 81920 29044735 14481408 7 HPFS/NTFS/exFAT /dev/sda3 29044736 1005142015 488048640 7 HPFS/NTFS/exFAT /dev/sda4 1005154920 1953520064 474182572+ 83 Linux Disk /dev/sdb: 32.0 GB, 32017047552 bytes 255 heads, 63 sectors/track, 3892 cylinders, total 62533296 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xb4fd923d Device Boot Start End Blocks Id System /dev/sdb1 2048 16775167 8386560 84 OS/2 hidden C: drive If I type 'sudo parted -l', I get: Model: ATA WDC WD10JPVT-75A (scsi) Disk /dev/sda: 1000GB Sector size (logical/physical): 512B/4096B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 41.1MB 41.1MB primary fat16 diag 2 41.9MB 14.9GB 14.8GB primary ntfs boot 3 14.9GB 515GB 500GB primary ntfs 4 515GB 1000GB 486GB primary ext4 Model: ATA SAMSUNG SSD PM83 (scsi) Disk /dev/sdb: 32.0GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 8589MB 8588MB primary Warning: Unable to open /dev/sr0 read-write (Read-only file system). /dev/sr0 has been opened read-only. Error: Can't have a partition outside the disk! I've also tried a Kubuntu 12.04 and Linuxmint install disks, wityh the same problem. I'm completely lost here. Cheers, Kieran

  Read the article

• Sort algorithms that work on large amount of data

  - by Giorgio

  I am looking for sorting algorithms that can work on a large amount of data, i.e. that can work even when the whole data set cannot be held in main memory at once. The only candidate that I have found up to now is merge sort: you can implement the algorithm in such a way that it scans your data set at each merge without holding all the data in main memory at once. The variation of merge sort I have in mind is described in this article in section Use with tape drives. I think this is a good solution (with complexity O(n x log(n)) but I am curious to know if there are other (possibly faster) sorting algorithms that can work on large data sets that do not fit in main memory. EDIT Here are some more details, as required by the answers: The data needs to be sorted periodically, e.g. once in a month. I do not need to insert a few records and have the data sorted incrementally. My example text file is about 1 GB UTF-8 text, but I wanted to solve the problem in general, even if the file were, say, 20 GB. It is not in a database and, due to other constraints, it cannot be. The data is dumped by others as a text file, I have my own code to read this text file. The format of the data is a text file: new line characters are record separators. One possible improvement I had in mind was to split the file into files that are small enough to be sorted in memory, and finally merge all these files using the algorithm I have described above.

  Read the article

• Cost effective way to provide static media content

  - by james

  I'd like to be able to deliver around 50MB of static content, either in about 30 individual files up to 10MB or grouped into 3 compressed files, around 5k to 20k times a day. Ideally I'd like to put some sort of very basic security around providing the data to ensure that a request is from the expected source, but if tossing the security for a big reduction in price is possible then it's an option. Does anyone have any suggestions other than what I've found: Google AppEngine is $0.12/GB & I believe has a file size limit of 10MB so I'd have to break the data up a bit. So a rough calculation would seem to be that this would cost me about $30 to $120 a day. Or I've seen something like what seems to be just public static content delivery with no type of logic capabilities like Usenet.nl at what I think calculates to about $0.025/GB which would cost me about $6 to $25 a day. Any idea if I'm going about these calculations right & if there might be a better option for just static content on a decently high volume delivery? Again some basic security would be great but if cost is greatly reduced without it then I'm up for that.

  Read the article

• no aparece grub con gpt windows/ubuntu

  - by user100604

  I have an asus k55VM. The problem is that once done the partitions to install windows 7 finalize you and then ubuntu 12.10 the grub not to appear. On having created the table of partitions with gparted I did it in format msdos but then on having installed windows gently accepted me and he says to me that I must do it with format gpt therefore I erase the disc in the assistant of installation and believe a partition of 160 gb Later between with live CD to ubuntu and believe other partitions between which, one ext4 for ubuntu... I install and restart. On having restarted the grub does not go out but if the partitions appear of windows. To seeing if someone helps me am desperate. Thank you very much Tengo un asus k55VM. El problema es que una vez hechas las particiones instalar windows 7 ultimate y luego ubuntu 12.10 no aparece el grub. Al crear la tabla de particiones con gparted lo hice en formato msdos pero luego al instalar windows no me acepta y me dice que debo hacerlo con formato gpt por lo tanto borro el disco en el asistente de instalacion y creo una particion de 160 gb Posteriormente entre con live cd a ubuntu y creo otras particiones entre las cuales, un ext4 para ubuntu... Instalo y reinicio. Al reiniciar no sale el grub pero si aparecen las particiones de windows. A ver si alguien me ayuda estoy desesperado. Muchas gracias

  Read the article

• disk space worngly displayed after installing LVM disk

  - by Ubuntuser

  I installed ubuntu server using LVM partitioning on a 1 TB hard disk. However, after installation, i can only see 10 Gig space here is the fidsk output ` # fdisk -l Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00041507 Device Boot Start End Blocks Id System /dev/sda1 * 1 10 71680 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 10 121602 976689152 8e Linux LVM Disk /dev/dm-0: 10.7 GB, 10737418240 bytes 255 heads, 63 sectors/track, 1305 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-0 doesn't contain a valid partition table Disk /dev/dm-1: 2147 MB, 2147483648 bytes 255 heads, 63 sectors/track, 261 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-1 doesn't contain a valid partition table You have new mail in /var/mail/root and df -h output df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/system-root 9.9G 6.6G 2.8G 71% / devtmpfs 1.9G 232K 1.9G 1% /dev tmpfs 1.9G 4.0K 1.9G 1% /dev/shm /dev/sda1 68M 22M 43M 34% /boot tmpfs 6.0G 0 6.0G 0% /var/spool/asterisk/monitor You have new mail in /var/mail/root ` any way to increase this space without reisntalling?

  Read the article

• Ubuntu Desktop does not load

  - by Niklas

  If I login on my Ubuntu 14.04, I get the following desktop: This weird behavior appeared after I executed sudo apt-get update && sudo apt-get upgrade and restarted my computer. Don't know why though. To my Ubuntu I have tried the following (nothing seems to work so far) Fix any broken packages: sudo apt-get update sudo apt-get autoclean sudo apt-get clean sudo apt-get autoremove Locate any broken packages and reinstall them: sudo apt-get install debsums sudo apt-get clean sudo debsums_init sudo debsums -cs sudo apt-get install --reinstall $(sudo dpkg -S $(sudo debsums -c) | cut -d : -f 1 | sort -u) Removing some compiz files: rm -r ~/.cache/compizconfig-1 rm -r ~/.compiz Purging of NVIDIA and installing NVIDIA-prime: sudo apt-get install --reinstall ubuntu-desktop sudo apt-get install unity sudo apt-get purge nvidia* bumblebee* sudo apt-get install nvidia-prime sudo shutdown -r now Compizconfig Settings Manager: sudo apt-get install compizconfig-settings-manager export DISPLAY=:0 ccsm // Back to UI and enablement of Unity Plugin Unity replace, which stopped at a while and did nothing afterwards unity --replace Some dconf reset dconf reset -f /org/compiz/ unity --reset-icons &disown Actually dconf did not work and I got this error: error: Cannot autolaunch D-Bus without X11 $DISPLAY Can anybody help me on that? This is my hardware (hope it helps in any way): Intel® Core™ i7-3770 ASUS GTX660TI-DC2-OG-2GD5 (NVIDIA driver is/was installed) ASUS P8Z77-V LX Corsair DIMM 8 GB DDR3-1600 Kit Samsung 830series 2,5" 256 GB (Windows is installed here) Seagate ST31000524AS 1 TB (3/4 are reserved for files; 1/4 is for Ubuntu (16GB swap included))

  Read the article

• Blank screen after GRUB (64 bit) - cannot install Ubuntu

  - by peGGi

  My laptop's specs: Lenovo IdeaPad Z570 Intel Core i5-2410M @ 2.3Ghz 6 Gb RAM DDR3 640 Gb ATAPI Hard-disk Drive @ 5,200 RPM NVIDIA GeForce G520M with Optimus switching technology Broadcom 802.11n Network Adapter REALTEK soundcard Windows 7 Home Premium 64-bit I downloaded Ubuntu Studio 11.04 and burned the iso image onto two different DVDs, using two different programs (one DVD is RW, the other is just R). I verified the hash MD5sum thing. I get as far as GRUB with the 4 options (install, advanced install, disk verification, system rescue) but no matter which one I select, I get a blank screen and nothing happens. The DVD drive spins down after about 30 seconds. Also just before the GRUB screen I get a message saying Error: "Prefix" is not set. I'm not sure if that's relevant. I have tried all the options using both DVDs. Same thing happens. I have changed the graphics setting in BIOS to UMA or Optimus, but still happens either way. I've tried booting with the wireless switch turned off, same thing happens. I downloaded 'vanilla' Ubuntu 64-bit and burned onto a CD, and the same thing happens. I have downloaded Ubuntu 32-bit and I am able to boot from the live CD (interestingly the wireless card won't work, but that's maybe another issue). I have searched extensively through these forums and other sites but I can't see anything that will help me. Is there something I'm missing? I'd really appreciate help on this. The laptop is less than 2 weeks old. I was so looking forward to getting Ubuntu Studio up and running. I've gone about as far as my technical abilities will allow.

  Read the article

• Can't access external hard drives or thumb drives

  - by calden

  I am not a complete linux noob but I don't know a lot either and would greatly appreciate some help with this. I just installed Ubuntu 10.10 onto my laptop. Everything is working great however USB devices such as thumb drives and external hard drives wont show up. I have been looking around a bit and when I run sudo fdisk -l it displays this: Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00065684 Device Boot Start End Blocks Id System /dev/sda1 * 1 29255 234983424 83 Linux /dev/sda2 29255 30402 9212929 5 Extended /dev/sda5 29255 30402 9212928 82 Linux swap / Solaris Disk /dev/sdb: 16.0 GB, 16026435072 bytes 64 heads, 32 sectors/track, 15283 cylinders Units = cylinders of 2048 * 512 = 1048576 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000df90d Device Boot Start End Blocks Id System /dev/sdb1 * 1 15283 15649776 7 HPFS/NTFS It does seem to display my 16 gig thumb drive but other then seeing it here I cant access it to read and write files to it. It does the same with my external hard drive. I know those devices work as I have tried them on my other computer and they are working fine. Also this is what is in fstab if this will help anybody help me: proc /proc proc nodev,noexec,nosuid 0 0 /dev/sdb1 / ext4 errors=remount-ro 0 1 /dev/sdb5 none swap sw 0 0 Thank you very much for the help everyone.

  Read the article

• Ubuntu installer does not show drives

  - by Tanweer Rashid

  I am trying to install Ubuntu 12.04 LTS on my Inspiron laptio, but the installer does not show any drives. My system has a 1TB SATA drive and a 32GB SSD. As far as I can figure, the boot files are kept on the SSD for fast startup (for Windows). During Win7 installation, I had to manually load drivers for RAID controller to see all available drives. Running fdisk -l from the live CD shows the following: ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x234b4782 Device Boot Start End Blocks Id System /dev/sda1 63 80324 40131 de Dell Utility /dev/sda2 * 81920 41627647 20772864 7 HPFS/NTFS/exFAT /dev/sda3 41627648 357019647 157696000 7 HPFS/NTFS/exFAT /dev/sda4 357019648 1953517567 798248960 f W95 Ext'd (LBA) /dev/sda5 672415744 1312966655 320275456 7 HPFS/NTFS/exFAT /dev/sda6 1312968704 1953517567 320274432 7 HPFS/NTFS/exFAT Disk /dev/sdb: 32.0 GB, 32017047552 bytes 255 heads, 63 sectors/track, 3892 cylinders, total 62533296 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x234b474b Device Boot Start End Blocks Id System /dev/sdb1 2048 16775167 8386560 84 OS/2 hidden C: drive ubuntu@ubuntu:~$ In the Ubuntu installer, I can only choose /dev/sdb for "Device for boot loader installation", and sdb doesn't show any drives. I cannot select /dev/sda. Any ideas anyone? Thanks.

  Read the article

• Can't install Ubuntu, black screen after install

  - by Tyrone

  I tried several times, but wasn't able to make it work. I tried all recent types of Ubuntu but it didn't work. Then I tried acpi=off at the beginning of the installation. In this way I could finish the installation. But after the restart Ubuntu didn't work. Only a black screen appeared. Before that I tried it on the VirtualBox and it work. By the way my system is the following: (I use windows 7 currently) Processor AMD Athlon II P320 (2,1 GHz, second-level cache 2 ? 512 KB, HT 1600 MHz bus) Chipset AMD M880G + SB850 Memory Dual Channel, 3 GB DDR3-1066 Wide Screen 15.6 “high-definition (1366 ? 768) c LED-backlit, AU Optronics B156XW02 Video Card AMD Radeon HD 4250, from 336 MB video buffer in memory, support for DirectX 10.1 and UVD Sound system: HDA-codec IDT 92HD81B1X AMD HDMI Audio Hard drive WDC WD3200BEVT-75A23T0 (298 GB, 5400 RPM, SATA 2.0) Optical Drive: DVD ± RW Optiarc AD-7585H Communication tools Fast Ethernet (10/100 Mbit / c) Realtek RTL8102E/RTL8103E WiFi 802.11a/b/g Broadcom BCM4310 Bluetooth 2.1 + EDR Card reader Memory Card Reader 7-in-1 with support for SD / SDHC / MMC / MS / xD, and derivatives Interfaces / ports 3 USB 2.0 1 eSATA + USB 2.0 15-pin video connector VGA HDMI RJ-45 Ethernet 10/100 Mbit / c 2 analog mini-jack: a microphone / headphone jack for a Kensington lock slot AC adapter Battery Li-Ion 6-cell capacity of 4400 mA ? h (10,8, 48 W ? hr) AC power adapter 65 Watt Additional equipment integrated web-camera (1.3 mega pixels)

  Read the article

• Ubuntu unstable, showing awkward behavior

  - by Christophe De Troyer

  Let me start off by saying that this problem can't be described in such a way that allows me to find other topics, which have some relevance to this problem. That's why I created this question. In case this question might have been asked before, I apologize. So what is the problem: My computer (Intel Core I5 2500K - with HD3000 graphics -, 6 gb DDR, 1 SSD, 3 HDD's and an Asus P8Z68 mobo) runs Windows on the SDD. But I decided to give Ubuntu a chance to be my daily OS for basic needs since it's open source and I find it a handicap of not being able to work with it. I decided to run the windows installer and install Ubuntu 12.04 to my 320 Gb hdd which was not being used in my computer. After installing it and booting it, it worked great! I spent the rest of the day/night using it, and falling for it. Great, today I booted Ubuntu (I had the choice in the bootloader as I expected). It asked me for my login and it started logging in. Now, after a few (literally) minutes of letting it "boot" I tried determining the cause of this. What I've figured out so far: When I left click on my desktop it freezes completely for a few seconds I have something like tearing in the left side menu (in games, you know) when I move my mouse around It runs well when just hovering around with my mouse, but from the point I click on something it freezes. What have I tried? I ran a HD Tune diagnostic on the HDD but the performance seems to be very close to the stock values, so I'm taking it as a good HDD. I'm trying to get to the drivers update panel for Ubuntu, but with the state it's in, it's taking a lot of time.. Could anyone point me in a direction for troubleshooting this? I'm not really a noob at all, just when using Linux.. :) Thanks in advance! Christophe,

  Read the article

• How do I get back hard drive space after I have uninstalled Ubuntu from Windows?

  - by Shantanu

  I installed Ubuntu on windows like it says to do it on Ubuntu's website as an application. I did not want it to create a separate partition on my hard drive. A few days ago, I uninstalled Ubuntu by going into the Windows control panel and hitting uninstall. As you would expect, I would get back my 100 or so gb on the disc. i never really installed anything of importance on ubuntu so i never had a second thought about uninstalling it. But I never got back my 100gb from Ubuntu. Now when I add up all of the folders on my c drive, they total to the amount I had on windows before I uninstalled Ubuntu but when I look at the My Computer screen, it says that another 100 or so gb is missing. I tried defragmenting the disc, downloading various disc managers but nothing fixed the space problem. Can anyone please help me with this!!??? Any help is much appreciated! Just making sure: UBUNTU WAS NOT ON A SEPARATE PARTITION, IT WAS INSTALLED AS AN APPLICATION ON WINDOWS. It tells yuo how to do this here except i did it with a much older version (i think it was 8.04 or soemthing): http://www.ubuntu.com/download/help/install-ubuntu-with-windows

  Read the article

• Ubuntu 13.04 to 13.10: Filesystem check or mount failed

  - by SamHuckaby

  I attempted to upgrade from Ubuntu 13.04 to 13.10 today, and mid upgrade the system started flaking out, and eventually locked up entirely. I was forced to restart the computer, and am now unable to get the computer to boot up at all. When I boot currently, it takes me to the GRUB menu, and I can choose to boot normally, or boot in an older version. I have tried several things, which I list below, but no matter what, when I try to finish booting into Ubuntu, I receive the following error: Filesystem check or mount failed. A maintenance shell will now be started. CONTROL-D will terminate this shell and continue booting after re-trying filesystems. Any further errors will be ignored root@ubuntu-computername:~# I have fun fsck -f and everything appears correct, no errors are reported. and it passes all 5 checks. If I run fdisk -l then I get the following information: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 4096 bytes / 4096 bytes Disk identifier: 0x00010824 Device Boot Start End Blocks Id System /dev/sda1 * 2048 608456703 304227328 83 Linux /dev/sda2 608458750 625141759 8341505 5 Extended Partition 2 does not start on physical sector boundary. /dev/sda5 608458752 625141759 8341504 82 Linux swap / Solaris Disk /dev/sdb: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0fb4b7e8 Device Boot Start End Blocks Id System /dev/sdb1 8192 625139711 312565760 7 HPFS/NTFS/exFAT I am considering just installing a new OS on the other disk, that currently has nothing on it, and then just attempting to scrape my data off the old disk (thankfully I didn't encrypt the files). Really my question is this: Can I salvage this Ubuntu install, or should I give up and just reinstall?

  Read the article

• Recovering data from /

  - by Abhijit Gavas

  I accidentally installed Ubuntu to one of my data drives from Windows. The drive was a NTFS drive and contained about 80 GB of important data. The size of the drive is 110 GB. Its new file system is ext4. In an attempt to recover the data, I downloaded foremost and tried the following commands: foremost -i / -o /media/281C8DB01C8D7998/Recovery/ -T -v foremost -i /dev/sda7 -o /media/281C8DB01C8D7998/Recovery/ -T -v (sda7 is the drive in question.) It appears that with either command, foremost gets stuck reading some file. Here is the console output: abhi@abi-PC:/dev$ foremost -i /dev/sda7 -o /media/281C8DB01C8D7998/Recovery/ -T -v Foremost version 1.5.7 by Jesse Kornblum, Kris Kendall, and Nick Mikus Audit File Foremost started at Fri Sep 28 20:58:00 2012 Invocation: foremost -i /dev/sda7 -o /media/281C8DB01C8D7998/Recovery/ -T -v Output directory: /media/281C8DB01C8D7998/Recovery_Fri_Sep_28_20_58_00_2012 Configuration file: /etc/foremost.conf Processing: stdin |------------------------------------------------------------------ File: stdin Start: Fri Sep 28 20:58:00 2012 Length: Unknown Num Name (bs=512) Size File Offset Comment Killed As you can see I have to kill it from system monitor. This approach does not seem to be working. What else could I try to recover the files? Please help. The files are very important and I will be devastated if I cannot recover them.

  Read the article

• Stylecop 4.7.37.0 has been released

  - by TATWORTH

  Stylecop  4.7.37.0 has been released at http://stylecop.codeplex.com/releases/view/79972The release notes follow:Add docs for new SA1650 spelling rule.Fix for 7395. Dont remove parenthesis around await expressions.Insert a returns element into docs within a see element.Update our tools folder StyleCop dll'sfix for 7392. Insert generic type docs for return types correctly.Fix for 7393. Allow documentation elements with attributes to end the string and still be valid.Make sure the MSBuild Task logs the warning id and type of exception. Unless the description field holds all this info VS cannot show the text in the Error List.Load custom dictionaries for multiple cultures. For a culture like en-GB; we load CustomDictionary.xml, then look for CustomDictionary.en-GB.xml and then CustomDictionary.en.xmlUpdate standard shipping dictionaries.Element documentation spelling fixes.Reduce the standard dictionaryUpdate our own devbuild StyleCop checks.Don't check spelling of xml documentation attributes are anything inside  <c> or <code> elements.Update StylingStyling update.Add timestamps for all the dependant files into the StyleCopResults.cache. Add a FileSystemWatcher to all custom dictionary files.Write out the full violation into the StyleCopResults.cache.Change a rules description text.Styling fixes.Styling fixes.NEW RULE: Check Spelling Of Element Documetation. Fix over 2000 spelling errors in our source code. Update the VS addin to show the rule violation in more detail. Add spelling checker to the deployment.Set our own Culture to en-USDocumentation spelling fixes.First draft of the documentation spelling checker.Fix for 7325. Don't throw 1126 in goto statements.Fix for 7090. Add TargetsDir to registry during install.Fix for 7060. Sort usings after moving them inside namespace.Fix FxCop issues.Fix for 7389. Detect CpuCount on Unix/MACFix for 6788. Allow opening curly brackets for scope. Added new tests.Updating constants.Fix for 7167. Show version number of StyleCop in VS Help window.Only output StyleCop excluded files if there are any.

  Read the article

• Windows 8 BIOS - Boot Ubuntu from External HDD

  - by F3AR3DLEGEND

  My laptop came pre-loaded with Windows 8 64-bit (only storage device is a 128 GB SSD). Since it is my school laptop/I've heard creating a Linux partition alongside Windows 8 is not very wise I installed Ubuntu onto my external hard drive. I have a 500GB external HDD with the following partitions: Main Partition - NFTS - ~400 GB Extension Partition / - ext2 - ~25gb /home - ext2 - ~30gb swap - ext2 - 10gb /boot - ? - 10gb ? = not sure of partition Using the PenDriveLinux installer, I created a LiveUSB version of Ubuntu 12.04 (LTS) on a 4GB USB drive. Using that, I installed Ubuntu onto the external hard-drive, without any errors (or at least none that I was notified of). Using the BIOS settings, I changed the OS-loading order so that it is in this order: My External USB HDD Windows Boot Loader Some other things Therefore, Ubuntu should load from my hard drive first, but it doesn't. Also, my hard drive is in working condition, and it turns on when BIOS starts (there is a light indicator). When I start my laptop, it goes directly to Windows 8 (I have the fast startup setting disabled as well). So, is there any way for me to set it up so that when my HDD is connected, it will automatically load Ubuntu? Thanks in advance!

  Read the article

• Ubuntu installation does not recognize drive partinioning

  - by Woltan

  I have a 1TB drive and installed Windows 7 on a 128GB partition. When I now try to install Ubuntu 11.04 it does not recognize the Windows partition but offers the complete 1TB drive to install Ubuntu on instead. It displays: However, in the Ubuntu Disk Utility the Windows partitions are recognized. What do I need to do in order for Ubuntu to recognize the Windows 7 partition and install Ubuntu as a dual boot? Response to comments The following commands were executed and the results are shown below: fdisk -l WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x34a38165 Device Boot Start End Blocks Id System /dev/sda1 * 1 13 102400 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 13 16318 130969600 7 HPFS/NTFS Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x14a714a6 Device Boot Start End Blocks Id System /dev/sdb1 1 60801 488384001 83 Linux parted -l Warning: Unable to open /dev/sr0 read-write (Read-only file system). /dev/sr0 has been opened read-only. Error: /dev/sr0: unrecognised disk label

  Read the article

• Unable to mount an LVM Hard-drive after upgrade

  - by Bruce Staples

  I imagine this is a basic gotcha ... but I can't see it. I have a system with 2(physical) harddrives. The boot system (/dev/sda) was running 10.04 & the second drive (/dev/sdb) was just a mounted filesystem. I did a clean load of Ubuntu 12.04 overwriting /dev/sda (not an upgrade) & now cannot mount the second drive. so I do not know what to enter it into the fstab ... I had expected to use: /dev/sdb /tera ext4 defaults 0 2 But even manual mounting fails (I also have tried various "-t" options on the off chance!) sudo mount -t ext4 /dev/sdb1 /tera mount: wrong fs type, bad option, bad superblock on /dev/sdb1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so Output from disk queries indicate that it is a Linux LVM & a healthy disk still. sudo lshw -C disk *-disk:0 description: ATA Disk product: WDC WD5000AACS-0 vendor: Western Digital physical id: 0 bus info: scsi@2:0.0.0 logical name: /dev/sda version: 01.0 serial: WD-WCASU1401098 size: 465GiB (500GB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=00015a55 *-disk:1 description: ATA Disk product: WDC WD10EADS-00L vendor: Western Digital physical id: 1 bus info: scsi@3:0.0.0 logical name: /dev/sdb version: 01.0 serial: WD-WCAU47836304 size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 sudo fdisk -l Disk /dev/sda: 500.1 GB, 500106780160 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976771055 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00015a55 Device Boot Start End Blocks Id System /dev/sda1 * 2048 972580863 486289408 83 Linux /dev/sda2 972582910 976769023 2093057 5 Extended /dev/sda5 972582912 976769023 2093056 82 Linux swap / Solaris Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 1953525167 976762583+ 8e Linux LVM LVM doesn't appear to be an option for mount or fstab. ... and here's a Smart data Screenshot from Disk Utility.

  Read the article

• How to re-add RAID-10 dropped drive?

  - by thiesdiggity

  I have a problem that I can't seem to solve. We have a Ubuntu server setup with RAID-10 and two of the drives dropped out of the array. When I try to re-add them using the following command: mdadm --manage --re-add /dev/md2 /dev/sdc1 I get the following error message: mdadm: Cannot open /dev/sdc1: Device or resource busy When I do a "cat /proc/mdstat" I get the following: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [r$ md2 : active raid10 sdb1[0] sdd1[3] 1953519872 blocks 64K chunks 2 near-copies [4/2] [U__U] md1 : active raid1 sda2[0] sdc2[1] 468853696 blocks [2/2] [UU] md0 : active raid1 sda1[0] sdc1[1] 19530688 blocks [2/2] [UU] unused devices: <none> When I run "/sbin/mdadm --detail /dev/md2" I get the following: /dev/md2: Version : 00.90 Creation Time : Mon Sep 5 23:41:13 2011 Raid Level : raid10 Array Size : 1953519872 (1863.02 GiB 2000.40 GB) Used Dev Size : 976759936 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Thu Oct 25 09:25:08 2012 State : active, degraded Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K UUID : c6d87d27:aeefcb2e:d4453e2e:0b7266cb Events : 0.6688691 Number Major Minor RaidDevice State 0 8 17 0 active sync /dev/sdb1 1 0 0 1 removed 2 0 0 2 removed 3 8 49 3 active sync /dev/sdd1 Output of df -h is: Filesystem Size Used Avail Use% Mounted on /dev/md1 441G 2.0G 416G 1% / none 32G 236K 32G 1% /dev tmpfs 32G 0 32G 0% /dev/shm none 32G 112K 32G 1% /var/run none 32G 0 32G 0% /var/lock none 32G 0 32G 0% /lib/init/rw tmpfs 64G 215M 63G 1% /mnt/vmware none 441G 2.0G 416G 1% /var/lib/ureadahead/debugfs /dev/mapper/RAID10VG-RAID10LV 1.8T 139G 1.6T 8% /mnt/RAID10 When I do a "fdisk -l" I can see all the drives needed for the RAID-10. The RAID-10 is part of the /dev/mapper, could that be the reason why the device is coming back as busy? Anyone have any suggestions on what I can try to get the drives back into the array? Any help would be greatly appreciated. Thanks!

  Read the article

< Previous Page | 36 37 38 39 40 41 42 43 44 45 46 47  | Next Page >