Search Results

Search found 1031 results on 42 pages for 'subnet'.

Page 40/42 | < Previous Page | 36 37 38 39 40 41 42  | Next Page >

• VirtualBox - Public Static IP for a Debian Guest on a Dedicated Server

  - by user86296

  Goal: I want to run a Debian-squeeze-Guest in VirtualBox and it's own public static ip. I found tons of threads about this topic, but all in all I'm now trying for 10 hours (reading the manual, the forums, trying to learn about networking concepts & commands) to give a Guest his own public static ip (so that the Guest is similar to a vServer you can order from a hosting company), but wasn't able to. Since I'm a big noob as far as networking stuff is concerned, I'm probably doing something wrong.(please bear with me :-) ) Situation: VirtualBox 4.0.10 (headless no gui) is running on a dedicated Debian-Server, the Guest OS is Debian as well. The server has a static ip and I ordered an additional ip for a VM. Problem description: Upto now I was able to use NAT to access the VM from the outside and to setup an internal network between several Guests and all of this worked very well. When setting NIC 1 to bridged and configuring a public static ip on the guest, the guest was unpingable. (neither from outside, nor from the host) I could connect to the guest via the internal network, from another vm, though. ( VBoxManage controlvm VMGuest nic1 bridged eth0 ) ( configuration attempt of static-ip on the guest '/etc/network/interfaces' is below) Please let me know what I'm doing wrong, or what I can try to get it to work, or if you need more info. I think I've read that with a current VirtualBox-version for bridged networking no special host-configuration is necessary, is that accurate, or might that be the problem? Additional Info Info I got from the hosting company about the additional IP Please note that you can use the IP address only for this server. IP: 46.4.xx.xx Gateway: 46.4.xx.xx Mask: 255.255.255.248 VBoxManage showvminfo VMGuest |less ... NIC 1: MAC: 080027D72F7B, Attachment: Bridged Interface 'eth0', Cable connected: on, Trace: off (file: none), Type: 82540EM, Reported speed: 0 Mbps, Boot priority: 0 NIC 2: MAC: 080027B03B75, Attachment: Internal Network 'InternalNet1', Cable connected: on, Trace: off (file: none), Type: Am79C973, Reported speed: 0 Mbps, Boot priority: 0 NIC 3: disabled (...rest is disabled) cat /etc/network/interfaces on the Host-machine # Loopback device: auto lo iface lo inet loopback # device: eth0 auto eth0 iface eth0 inet static address 46.4.xx.xx broadcast 46.4.xx.xx netmask 255.255.255.224 gateway 46.4.xx.xx post-up mii-tool -F 100baseTx-FD eth0 # default route to access subnet up route add -net 46.4.xx.xx netmask 255.255.255.224 gw 46.4.xx.xx eth0 cat /etc/network/interfaces on the Guest-VM # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 auto eth0 iface eth0 inet static address 46.4.xx.xx netmask 255.255.255.248 gateway 46.4.xx.xx auto eth1 iface eth1 inet dhcp ifconfig -a on the Guest shows the correct static ip for eth0 but the Guest is unreachable "over eth0" eth0 Link encap:Ethernet HWaddr 08:00:27:d7:2f:7b inet addr:46.4.xx.xx Bcast:46.4.xx.xx Mask:255.255.255.248 inet6 addr: fe80::a00:27ff:fed7:2f7b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:21 errors:0 dropped:0 overruns:0 frame:0 TX packets:69 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1260 (1.2 KiB) TX bytes:3114 (3.0 KiB) eth1 Link encap:Ethernet HWaddr 08:00:27:b0:3b:75 inet addr:192.168.10.3 Bcast:192.168.10.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:feb0:3b75/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:142 errors:0 dropped:0 overruns:0 frame:0 TX packets:92 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:15962 (15.5 KiB) TX bytes:14540 (14.1 KiB) Interrupt:16 Base address:0xd240 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:123 errors:0 dropped:0 overruns:0 frame:0 TX packets:123 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:25156 (24.5 KiB) TX bytes:25156 (24.5 KiB)

  Read the article

• More Great Improvements to the Windows Azure Management Portal

  - by ScottGu

  Over the last 3 weeks we’ve released a number of enhancements to the new Windows Azure Management Portal.  These new capabilities include: Localization Support for 6 languages Operation Log Support Support for SQL Database Metrics Virtual Machine Enhancements (quick create Windows + Linux VMs) Web Site Enhancements (support for creating sites in all regions, private github repo deployment) Cloud Service Improvements (deploy from storage account, configuration support of dedicated cache) Media Service Enhancements (upload, encode, publish, stream all from within the portal) Virtual Networking Usability Enhancements Custom CNAME support with Storage Accounts All of these improvements are now live in production and available to start using immediately.  Below are more details on them: Localization Support The Windows Azure Portal now supports 6 languages – English, German, Spanish, French, Italian and Japanese. You can easily switch between languages by clicking on the Avatar bar on the top right corner of the Portal: Selecting a different language will automatically refresh the UI within the portal in the selected language: Operation Log Support The Windows Azure Portal now supports the ability for administrators to review the “operation logs” of the services they manage – making it easy to see exactly what management operations were performed on them.  You can query for these by selecting the “Settings” tab within the Portal and then choosing the “Operation Logs” tab within it.  This displays a filter UI that enables you to query for operations by date and time: As of the most recent release we now show logs for all operations performed on Cloud Services and Storage Accounts.  You can click on any operation in the list and click the “Details” button in the command bar to retrieve detailed status about it.  This now makes it possible to retrieve details about every management operation performed. In future updates you’ll see us extend the operation log capability to apply to all Windows Azure Services – which will enable great post-mortem and audit support. Support for SQL Database Metrics You can now monitor the number of successful connections, failed connections and deadlocks in your SQL databases using the new “Dashboard” view provided on each SQL Database resource: Additionally, if the database is added as a “linked resource” to a Web Site or Cloud Service, monitoring metrics for the linked SQL database are shown along with the Web Site or Cloud Service metrics in the dashboard. This helps with viewing and managing aggregated information across both resources in your application. Enhancements to Virtual Machines The most recent Windows Azure Portal release brings with it some nice usability improvements to Virtual Machines: Integrated Quick Create experience for Windows and Linux VMs Creating a new Windows or Linux VM is now easy using the new “Quick Create” experience in the Portal: In addition to Windows VM templates you can also now select Linux image templates in the quick create UI: This makes it incredibly easy to create a new Virtual Machine in only a few seconds. Enhancements to Web Sites Prior to this past month’s release, users were forced to choose a single geographical region when creating their first site.  After that, subsequent sites could only be created in that same region.  This restriction has now been removed, and you can now create sites in any region at any time and have up to 10 free sites in each supported region: One of the new regions we’ve recently opened up is the “East Asia” region.  This allows you to now deploy sites to North America, Europe and Asia simultaneously.  Private GitHub Repository Support This past week we also enabled Git based continuous deployment support for Web Sites from private GitHub and BitBucket repositories (previous to this you could only enable this with public repositories).  Enhancements to Cloud Services Experience The most recent Windows Azure Portal release brings with it some nice usability improvements to Cloud Services: Deploy a Cloud Service from a Windows Azure Storage Account The Windows Azure Portal now supports deploying an application package and configuration file stored in a blob container in Windows Azure Storage. The ability to upload an application package from storage is available when you custom create, or upload to, or update a cloud service deployment. To upload an application package and configuration, create a Cloud Service, then select the file upload dialog, and choose to upload from a Windows Azure Storage Account: To upload an application package from storage, click the “FROM STORAGE” button and select the application package and configuration file to use from the new blob storage explorer in the portal. Configure Windows Azure Caching in a caching enabled cloud service If you have deployed the new dedicated cache within a cloud service role, you can also now configure the cache settings in the portal by navigating to the configuration tab of for your Cloud Service deployment. The configuration experience is similar to the one in Visual Studio when you create a cloud service and add a caching role.  The portal now allows you to add or remove named caches and change the settings for the named caches – all from within the Portal and without needing to redeploy your application. Enhancements to Media Services You can now upload, encode, publish, and play your video content directly from within the Windows Azure Portal.  This makes it incredibly easy to get started with Windows Azure Media Services and perform common tasks without having to write any code. Simply navigate to your media service and then click on the “Content” tab.  All of the media content within your media service account will be listed here: Clicking the “upload” button within the portal now allows you to upload a media file directly from your computer: This will cause the video file you chose from your local file-system to be uploaded into Windows Azure.  Once uploaded, you can select the file within the content tab of the Portal and click the “Encode” button to transcode it into different streaming formats: The portal includes a number of pre-set encoding formats that you can easily convert media content into: Once you select an encoding and click the ok button, Windows Azure Media Services will kick off an encoding job that will happen in the cloud (no need for you to stand-up or configure a custom encoding server).  When it’s finished, you can select the video in the “Content” tab and then click PUBLISH in the command bar to setup an origin streaming end-point to it: Once the media file is published you can point apps against the public URL and play the content using Windows Azure Media Services – no need to setup or run your own streaming server.  You can also now select the file and click the “Play” button in the command bar to play it using the streaming endpoint directly within the Portal: This makes it incredibly easy to try out and use Windows Azure Media Services and test out an end-to-end workflow without having to write any code.  Once you test things out you can of course automate it using script or code – providing you with an incredibly powerful Cloud Media platform that you can use. Enhancements to Virtual Network Experience Over the last few months, we have received feedback on the complexity of the Virtual Network creation experience. With these most recent Portal updates, we have added a Quick Create experience that makes the creation experience very simple. All that an administrator now needs to do is to provide a VNET name, choose an address space and the size of the VNET address space. They no longer need to understand the intricacies of the CIDR format or walk through a 4-page wizard or create a VNET / subnet. This makes creating virtual networks really simple: The portal also now has a “Register DNS Server” task that makes it easy to register DNS servers and associate them with a virtual network. Enhancements to Storage Experience The portal now lets you register custom domain names for your Windows Azure Storage Accounts.  To enable this, select a storage resource and then go to the CONFIGURE tab for a storage account, and then click MANAGE DOMAIN on the command bar: Clicking “Manage Domain” will bring up a dialog that allows you to register any CNAME you want: Summary The above features are all now live in production and available to use immediately.  If you don’t already have a Windows Azure account, you can sign-up for a free trial and start using them today.  Visit the Windows Azure Developer Center to learn more about how to build apps with it. One of the other cool features that is now live within the portal is our new Windows Azure Store – which makes it incredibly easy to try and purchase developer services from a variety of partners.  It is an incredibly awesome new capability – and something I’ll be doing a dedicated post about shortly. Hope this helps, Scott P.S. In addition to blogging, I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu

  Read the article

• Troubleshooting Website problems within the local network

  - by HaydnWVN

  Have an external website which opens fine on some PC's, yet seems to time out (or symptoms of timing out, but never actually does) on others. Seems to only affect (some) of our newer HP Pro 3305 MT Workstations. All of which are running Win7 32bit SP1 with all updates. Older PC's (Win7 32bit SP1 & WinXP) are unaffected. Using Google Chrome & Firefox makes no difference. Opening the website in IE9 Compatibility Mode has exactly the same symptoms. All PC's are on the same local network (Workgroup) using the same DNS server & gateway (inhouse) on the same internet connection, on the same subnet. There is no proxy server, no content filtering, no load balancing etc etc. Only group policy in effect (locally) is for Update scheduling. Local firewalls are all the same (Kaspersky WP4) and our external facing firewall has no IP specific settings. I have no control over the external website, traceroute shows the same destination on all PC's. It is a fairly popular website in our industry (Horticulture) and i'm not aware of any other people (even other sites within our sister companies) with the same problem. Update: Used Fiddler2 to monitor the HTTP request, seems its not getting fulfilled for some reason?! Request sent: GET http://www.rhs.org.uk/ HTTP/1.1 Host: www.rhs.org.uk Connection: keep-alive User-Agent: Mozilla/5.0 (Windows NT 6.1) AppleWebKit/536.11 (KHTML, like Gecko) Chrome/20.0.1132.47 Safari/536.11 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Encoding: gzip,deflate,sdch Accept-Language: en-GB,en-US;q=0.8,en;q=0.6 Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 Log from Fiddler 2 of the request: This session is not yet complete. Press F5 to refresh when session is complete for updated statistics. Request Count: 1 Bytes Sent: 567 (headers:567; body:0) Bytes Received: 0 (headers:0; body:0) ACTUAL PERFORMANCE -------------- ClientConnected: 17:02:33.720 ClientBeginRequest: 17:02:39.118 GotRequestHeaders: 17:02:39.118 ClientDoneRequest: 17:02:39.118 Determine Gateway: 0ms DNS Lookup: 0ms TCP/IP Connect: 46ms HTTPS Handshake: 0ms ServerConnected: 17:02:39.165 FiddlerBeginRequest: 17:02:39.165 ServerGotRequest: 17:02:39.165 ServerBeginResponse: 00:00:00.000 GotResponseHeaders: 00:00:00.000 ServerDoneResponse: 00:00:00.000 ClientBeginResponse: 00:00:00.000 ClientDoneResponse: 00:00:00.000 RESPONSE BYTES (by Content-Type) -------------- ~headers~: 0 Log of a successful request from a working PC (done this morning, excuse the timestamps being different from above): Request Count: 1 Bytes Sent: 493 (headers:493; body:0) Bytes Received: 20,413 (headers:525; body:19,888) ACTUAL PERFORMANCE -------------- ClientConnected: 08:22:47.766 ClientBeginRequest: 08:22:47.766 GotRequestHeaders: 08:22:47.766 ClientDoneRequest: 08:22:47.766 Determine Gateway: 0ms DNS Lookup: 26ms TCP/IP Connect: 30ms HTTPS Handshake: 0ms ServerConnected: 08:22:47.828 FiddlerBeginRequest: 08:22:47.828 ServerGotRequest: 08:22:47.828 ServerBeginResponse: 08:22:48.905 GotResponseHeaders: 08:22:48.905 ServerDoneResponse: 08:22:48.905 ClientBeginResponse: 08:22:48.905 ClientDoneResponse: 08:22:48.905 Overall Elapsed: 00:00:01.1388020 RESPONSE BYTES (by Content-Type) -------------- text/html: 19,888 ~headers~: 525 So my question has evolved into: What is the difference between the 2 requests and how do I determine why 1 PC is not getting a reply to it's GET request?

  Read the article

• OpenVPN - client-to-client traffic working in one direction but not the other

  - by user42055

  I have the following VPN configuration: +------------+ +------------+ +------------+ | outpost |----------------| kino |----------------| guchuko | +------------+ +------------+ +------------+ OS: FreeBSD 6.2 OS: Gentoo 2.6.32 OS: Gentoo 2.6.33.3 Keyname: client3 Keyname: server Keyname: client1 eth0: 10.0.1.254 eth0: 203.x.x.x eth0: 192.168.0.6 tun0: 192.168.150.18 tun0: 192.168.150.1 tun0: 192.168.150.10 P-t-P: 192.166.150.17 P-t-P: 192.168.150.2 P-t-P: 192.168.150.9 Kino is the server and has client-to-client enabled. All three machines have ip forwarding enabled, by this on the gentoo boxes: net.ipv4.conf.all.forwarding = 1 And this on the FreeBSD box: net.inet.ip.forwarding: 1 In the server's "ccd" directory is the following files: client1: iroute 192.168.0.0 255.255.255.0 client3: iroute 10.0.1.0 255.255.255.0 The server config has these routes configured: push "route 192.168.0.0 255.255.255.0" push "route 10.0.1.0 255.255.255.0" route 192.168.0.0 255.255.255.0 route 10.0.1.0 255.255.255.0 Kino's routing table looks like this: 192.168.150.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 10.0.1.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 192.168.0.0 192.168.150.2 255.255.255.0 UG 0 0 0 tun0 192.168.150.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 Outpost's like this: 192.168.150 192.168.150.17 UGS 0 17 tun0 192.168.0 192.168.150.17 UGS 0 2 tun0 192.168.150.17 192.168.150.18 UH 3 0 tun0 And Guchuko's like this: 192.168.150.0 192.168.150.9 255.255.255.0 UG 0 0 0 tun0 10.0.1.0 192.168.150.9 255.255.255.0 UG 0 0 0 tun0 192.168.150.9 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 Now, the tests. Pings from Guchuko to Outpost's LAN IP work OK, as does the reverse - pings from Outpost to Guchuko's LAN IP. However... Pings from Outpost, to a machine on Guchuko's LAN work fine: .(( root@outpost )). (( 06:39 PM )) :: ~ :: # ping 192.168.0.3 PING 192.168.0.3 (192.168.0.3): 56 data bytes 64 bytes from 192.168.0.3: icmp_seq=0 ttl=63 time=462.641 ms 64 bytes from 192.168.0.3: icmp_seq=1 ttl=63 time=557.909 ms But a ping from Guchuko, to a machine on Outpost's LAN does not: .(( root@guchuko )). (( 06:43 PM )) :: ~ :: # ping 10.0.1.253 PING 10.0.1.253 (10.0.1.253) 56(84) bytes of data. --- 10.0.1.253 ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 2000ms Guchuko's tcpdump of tun0 shows: 18:46:27.716931 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 1, length 64 18:46:28.716715 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 2, length 64 18:46:29.716714 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 3, length 64 Outpost's tcpdump on tun0 shows: 18:44:00.333341 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 3, length 64 18:44:01.334073 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 4, length 64 18:44:02.331849 IP 192.168.150.10 > 10.0.1.253: ICMP echo request, id 63009, seq 5, length 64 So Outpost is receiving the ICMP request destined for the machine on it's subnet, but appears not be forwarding it. Outpost has gateway_enable="YES" in its rc.conf which correctly sets net.inet.ip.forwarding to 1 as mentioned earlier. As far as I know, that's all that's required to make a FreeBSD box forward packets between interfaces. Is there something else I could be forgetting ?

  Read the article

• Dynamic DNS registration for VPN clients

  - by Eric Falsken

  I've got a VPN server set up in my Active Directory on a remote network. (VPN Server is separate box from DNS/AD) When I dial into the network (client machine is not a member of the AD) the machine does not register its IP or Hostname in the DNS. I've played with all possible combinations of DHCP and RRAS-allocated IP pools, and none of them seem to cause my client to register. Is it because my client has to be a member of the domain? Are there some security settins I can tweak so that it can register its hostname/ip? I've looked in the event logs (System and Security) for the AD, DNS, DHCP, RRAS, and the client machine, and don't see anything relating to DNS Registration. Here's the IPConfig on the client machine (once connected): PPP adapter My VPN Name: Connection-specific DNS Suffix . : mydomain.local Description . . . . . . . . . . . : My VPN Name Physical Address. . . . . . . . . : DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.1.22(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.1.52 <- DC1 192.168.1.53 <- DC2 NetBIOS over Tcpip. . . . . . . . : Enabled

  Read the article

• Hanging of host network connections when starting KVM guest on bridge

  - by Chris Phillips

  Hi, I've a KVM system upon which I'm running a network bridge directly between all VM's and a bond0 (eth0, eth1) on the host OS. As such, all machines are presented on the same subnet, available outside of the box. The bond is doing mode 1 active / passive, with an arp_ip_target set to the default gateway, which has caused some issues in itself, but I can't see the bond configs mattering here myself. I'm seeing odd things most times when I stop and start a guest on the platform, in that on the host I lose network connectivity (icmp, ssh) for about 30 seconds. I don't lose connectivity on the other already running VM's though... they can always ping the default GW, but the host can't. I say "about 30 seconds" but from some tests it actually seems to be 28 seconds usually (or at least, I lose 28 pings...) and I'm wondering if this somehow relates to the bridge config. I'm not running STP on the bridge at all, and the forwarding delay is set to 1 second, path cost on the bond0 lowered to 10 and port priority of bond0 also lowered to 1. As such I don't think that the bridge should ever be able to think that bond0 is not connected just fine (as continued guest connectivity implies) yet the IP of the host, which is on the bridge device (... could that matter?? ) becomes unreachable. I'm fairly sure it's about the bridged networking, but at the same time as this happens when a VM is started there are clearly loads of other things also happening so maybe I'm way off the mark. Lack of connectivity: # ping 10.20.11.254 PING 10.20.11.254 (10.20.11.254) 56(84) bytes of data. 64 bytes from 10.20.11.254: icmp_seq=1 ttl=255 time=0.921 ms 64 bytes from 10.20.11.254: icmp_seq=2 ttl=255 time=0.541 ms type=1700 audit(1293462808.589:325): dev=vnet6 prom=256 old_prom=0 auid=42949672 95 ses=4294967295 type=1700 audit(1293462808.604:326): dev=vnet7 prom=256 old_prom=0 auid=42949672 95 ses=4294967295 type=1700 audit(1293462808.618:327): dev=vnet8 prom=256 old_prom=0 auid=42949672 95 ses=4294967295 kvm: 14116: cpu0 unimplemented perfctr wrmsr: 0x186 data 0x130079 kvm: 14116: cpu0 unimplemented perfctr wrmsr: 0xc1 data 0xffdd694a kvm: 14116: cpu0 unimplemented perfctr wrmsr: 0x186 data 0x530079 64 bytes from 10.20.11.254: icmp_seq=30 ttl=255 time=0.514 ms 64 bytes from 10.20.11.254: icmp_seq=31 ttl=255 time=0.551 ms 64 bytes from 10.20.11.254: icmp_seq=32 ttl=255 time=0.437 ms 64 bytes from 10.20.11.254: icmp_seq=33 ttl=255 time=0.392 ms brctl output of relevant bridge: # brctl showstp brdev brdev bridge id 8000.b2e1378d1396 designated root 8000.b2e1378d1396 root port 0 path cost 0 max age 19.99 bridge max age 19.99 hello time 1.99 bridge hello time 1.99 forward delay 0.99 bridge forward delay 0.99 ageing time 299.95 hello timer 0.50 tcn timer 0.00 topology change timer 0.00 gc timer 0.04 flags vnet5 (3) port id 8003 state forwarding designated root 8000.b2e1378d1396 path cost 100 designated bridge 8000.b2e1378d1396 message age timer 0.00 designated port 8003 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags vnet0 (2) port id 8002 state forwarding designated root 8000.b2e1378d1396 path cost 100 designated bridge 8000.b2e1378d1396 message age timer 0.00 designated port 8002 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags bond0 (1) port id 0001 state forwarding designated root 8000.b2e1378d1396 path cost 10 designated bridge 8000.b2e1378d1396 message age timer 0.00 designated port 0001 forward delay timer 0.00 designated cost 0 hold timer 0.00 flags I do see the new port listed as learning, but in line with the forward delay, only for 1 or 2 seconds when polling the brctl output on a loop. All pointers, tips or stabs in the dark appreciated.

  Read the article

• Configuring dhcp module in FreeRadius (3.0.2 - Centos 6.5)

  - by mixja

  I am using the REST module to authorise a DHCP request. I would like to send an explicit DHCP NAK if the authorisation fails, however the DHCP module seems to return immediately if there is a failure and just ignores the DHCP request without any response. Here is my DHCP module configuration - if rest.authorize is successful, the if (ok) control block is hit, but if rest.authorize fails the if (fail) is never hit. dhcp DHCP-Discover { rest.authorize if (fail) { update reply { DHCP-Message-Type = DHCP-Nak } } if (ok) { update reply { DHCP-Message-Type = DHCP-Offer } update reply { DHCP-Domain-Name-Server = x.x.x.x DHCP-Domain-Name-Server = x.x.x.x DHCP-Subnet-Mask = 255.255.255.0 DHCP-Router-Address = x.x.x.x DHCP-IP-Address-Lease-Time = 3600 DHCP-DHCP-Server-Identifier = x.x.x.x } mac2ip } } Below is the output after a 401 Unauthorized is received. I am wanting to achieve a temporary block on DHCP for a specified (small) period of time. However the FreeRADIUS behaviour is to ignore duplicate requests for same DHCP transaction, meaning DHCP on client is blocked until it begins a new transaction. If a DHCP NAK can be sent, the DHCP client will initiate a new transaction after each NAK (i.e. DHCP Discover), meaning FreeRADIUS will process each DHCP Discover from the client, and the block will be removed much closer to the desired block time. Tue Jun 3 03:00:57 2014 : Debug: (3) rest : Sending HTTP GET to "http://xxxxxx//api/v1/dhcp/80%3Aea%3A96%3A2a%3Ab6%3Aaa" Tue Jun 3 03:00:57 2014 : Debug: (3) rest : Processing response header Tue Jun 3 03:00:57 2014 : Debug: (3) rest : Status : 401 (Unauthorized) Tue Jun 3 03:00:57 2014 : Debug: (3) rest : Skipping attribute processing, no body data received Tue Jun 3 03:00:57 2014 : Debug: rlm_rest (rest): Released connection (4) Tue Jun 3 03:00:57 2014 : Debug: (3) modsingle[authorize]: returned from rest (rlm_rest) for request 3 Tue Jun 3 03:00:57 2014 : Debug: (3) [rest.authorize] = fail Tue Jun 3 03:00:57 2014 : Debug: (3) } # dhcp DHCP-Discover = fail Tue Jun 3 03:00:57 2014 : Debug: (3) Finished request 3. Tue Jun 3 03:00:57 2014 : Debug: Waking up in 0.2 seconds. Tue Jun 3 03:00:58 2014 : Debug: Waking up in 4.6 seconds. Received DHCP-Discover of id 7b0fb2de from 172.19.0.9:67 to 172.19.0.12:67 Tue Jun 3 03:00:59 2014 : Debug: (3) No reply. Ignoring retransmit. Tue Jun 3 03:00:59 2014 : Debug: Waking up in 2.9 seconds. Received DHCP-Discover of id 7b0fb2de from 172.19.0.9:67 to 172.19.0.12:67 Tue Jun 3 03:01:02 2014 : Debug: (3) No reply. Ignoring retransmit. Tue Jun 3 03:01:02 2014 : Debug: Waking up in 0.4 seconds. Tue Jun 3 03:01:02 2014 : Debug: (2) Cleaning up request packet ID 2064626397 with timestamp +56 Tue Jun 3 03:01:02 2014 : Debug: Waking up in 1999991.0 seconds. Received DHCP-Discover of id 7b0fb2de from 172.19.0.9:67 to 172.19.0.12:67 Tue Jun 3 03:01:06 2014 : Debug: (3) No reply. Ignoring retransmit. Tue Jun 3 03:01:06 2014 : Debug: Waking up in 3999983.1 seconds. Received DHCP-Discover of id 7b0fb2de from 172.19.0.9:67 to 172.19.0.12:67 Tue Jun 3 03:01:15 2014 : Debug: (3) No reply. Ignoring retransmit. Tue Jun 3 03:01:15 2014 : Debug: Waking up in 7999966.3 seconds. Received DHCP-Discover of id 7b0fb2de from 172.19.0.9:67 to 172.19.0.12:67 Tue Jun 3 03:01:23 2014 : Debug: (3) No reply. Ignoring retransmit. Tue Jun 3 03:01:23 2014 : Debug: Waking up in 15999942.1 seconds.

  Read the article

• Can't communicate between lan ports on openwrt router

  - by ScaryAardvark

  I've got a WBMR-HP-G300H Buffalo Airstation router on which I've installed the lates OpenWRT software. All is working well (ADSL, WIFI etc) except for one niggle. I can't communicate between lan ports. i.e. if I have one computer connected on lan port 1 and I try to ping another computer on lan port 2 then I get "destination unreachable". I can ping both computers from the router itself and can also ping each computer from a seperate laptop connected wirelessly. All computers are in the same subnet range (10.0.0.?/24). I suspect that I may need to configure a vlan on the switch but everytime I try and do this with various google'ed configuration I keep freezing out all lan-ports and I have to revert back using a wirelessly connected laptop. Here's my /etc/config/network: config interface 'loopback' option ifname 'lo' option proto 'static' option ipaddr '127.0.0.1' option netmask '255.0.0.0' config interface 'lan' option type 'bridge' option proto 'static' option netmask '255.255.255.0' option ipaddr '10.0.0.1' option _orig_ifname 'eth0 wlan0' option _orig_bridge 'true' option ifname 'eth0' config adsl-device 'adsl' option fwannex 'a' option annex 'a2p' config interface 'wan' option _orig_ifname 'nas0' option _orig_bridge 'false' option proto 'pppoa' option encaps 'vc' option atmdev '0' option vci '38' option vpi '0' option username '?????????????' option password '??????????????' Any help would be warmly received. Here's some more config stuff. root@OpenWrt:~# ifconfig -a br-lan Link encap:Ethernet HWaddr 00:24:A5:BD:66:08 inet addr:10.0.0.1 Bcast:10.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:226576 errors:0 dropped:346 overruns:0 frame:0 TX packets:269292 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:26771676 (25.5 MiB) TX bytes:183986450 (175.4 MiB) eth0 Link encap:Ethernet HWaddr 00:24:A5:BD:66:08 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ifb0 Link encap:Ethernet HWaddr 36:60:EC:DF:13:A1 BROADCAST NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ifb1 Link encap:Ethernet HWaddr 4A:7B:75:67:54:E0 BROADCAST NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:780 errors:0 dropped:0 overruns:0 frame:0 TX packets:780 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:58369 (57.0 KiB) TX bytes:58369 (57.0 KiB) mon.wlan0 Link encap:UNSPEC HWaddr 00-24-A5-BD-66-08-00-48-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2424 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:320188 (312.6 KiB) TX bytes:0 (0.0 B) pppoa-wan Link encap:Point-to-Point Protocol inet addr:81.136.179.204 P-t-P:81.134.80.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:258894 errors:0 dropped:0 overruns:0 frame:0 TX packets:212976 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:177341656 (169.1 MiB) TX bytes:25192459 (24.0 MiB) wlan0 Link encap:Ethernet HWaddr 00:24:A5:BD:66:08 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:204063 errors:0 dropped:0 overruns:0 frame:0 TX packets:245516 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:26613140 (25.3 MiB) TX bytes:162799765 (155.2 MiB) root@OpenWrt:~# brctl show bridge name bridge id STP enabled interfaces br-lan 8000.0024a5bd6608 no wlan0 eth0 root@OpenWrt:~# swconfig dev eth0 show Global attributes: enable_vlan: 0 Port 0: pvid: 0 link: port:0 link:up speed:1000baseT full-duplex txflow rxflow Port 1: pvid: 0 link: port:1 link:down Port 2: pvid: 0 link: port:2 link:down Port 3: pvid: 0 link: port:3 link:down Port 4: pvid: 0 link: port:4 link:up speed:100baseT full-duplex txflow rxflow auto Port 5: pvid: 0 link: port:5 link:up speed:100baseT full-duplex txflow rxflow auto Regards Mark.

  Read the article

• can't connect 2 subnets through RRAS 2008 r2

  - by mcdwight6

  I'm working on a project for a networking class. In VMWare Workstation, I have to set up a 2008 r2 server with DHCP reservations for 2 clients on separate subnets and have them ping each other. Here is the output of the route print command: =========================================================================== Interface List 13 ...00 50 56 2a e7 11 ...... Intel(R) PRO/1000 MT Network Connection #3 10 ...00 0c 29 66 88 dd ...... Intel(R) PRO/1000 MT Network Connection 1 ........................... Software Loopback Interface 1 24 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 11 ...02 00 54 55 4e 01 ...... Teredo Tunneling Pseudo-Interface 14 ...00 00 00 00 00 00 00 e0 6TO4 Adapter 16 ...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 17 ...00 00 00 00 00 00 00 e0 isatap.{5B8FB196-616F-4168-A020-03E63A309CEC} =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 On-link 10.0.0.2 266 0.0.0.0 0.0.0.0 On-link 223.6.6.2 266 10.0.0.0 255.0.0.0 On-link 10.0.0.2 266 10.0.0.2 255.255.255.255 On-link 10.0.0.2 266 10.255.255.255 255.255.255.255 On-link 10.0.0.2 266 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.6.0.0 255.255.0.0 On-link 10.0.0.2 11 128.6.255.255 255.255.255.255 On-link 10.0.0.2 266 223.6.6.0 255.255.255.0 On-link 10.0.0.2 11 223.6.6.0 255.255.255.0 On-link 223.6.6.2 266 223.6.6.2 255.255.255.255 On-link 223.6.6.2 266 223.6.6.255 255.255.255.255 On-link 10.0.0.2 266 223.6.6.255 255.255.255.255 On-link 223.6.6.2 266 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.0.0.2 266 224.0.0.0 240.0.0.0 On-link 223.6.6.2 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.0.0.2 266 255.255.255.255 255.255.255.255 On-link 223.6.6.2 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 10.0.0.2 Default 0.0.0.0 0.0.0.0 128.6.0.2 Default 0.0.0.0 0.0.0.0 223.6.6.2 Default 128.6.0.0 255.255.0.0 10.0.0.2 1 223.6.6.0 255.255.255.0 10.0.0.2 1 =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 14 1010 2002::/16 On-link 14 266 2002:8006:2::8006:2/128 On-link 1 306 ff00::/8 On-link =========================================================================== Persistent Routes: None My problem is that although I have set up both dynamic and persistent static routes in my r2 server, neither of the clients can ping even the NIC outside its own subnet. For example Client A can ping the NIC at 10.0.0.2 and vice-versa, but it gets a general transmit failure when it tries to ping the card at 223.6.6.2, let alone trying to ping the other client. I have completely disabled the firewalls on all machines and anything else I could think of, without success. What am I missing? Edit: Since posting this, I also noticed that the default gateways on my 2 NICs keep getting zeroed out. Does anyone know a fix for this?

  Read the article

• ISP 5 Device Limit ... again

  - by Tommo

  Sorry for the delay in responding to the suggestions that were posted in my first question (ISP 5 Device Limit - double NAT the solution?). I've been travelling and have not been able to try anything. Below is what I've tried and where I have not been successful. Any more help gratefully appreciated. I figure I need to give a more comprehensive overview of what I've got and how it's set up. First of all - I am using all Apple products here. I am iMac, iPad, iPhone, Apple TV, Airport Express and Time Capsule. I used to like the way that it 'just worked'. Now I find that it requires a bit of encouragement before it 'just works'. So, as I stated in my original question; my ISP has a router in my building that is limiting me to 5 devices. I am hard wired into this router and I can neither access it physically nor logically (they won't let me access it). Also, I only appear to be able to connect to it through the LAN ports on my Time Capsule. Any device I connect appears to be on a rolling IP list with the following settings: Router 91.72.80.1 Devices then get assigned IPv4 addresses in the range (as far as I can see) from 91.72.80.2 onwards. SubNet Mask 255.255.255.0 DNS Servers 213.132.63.25, 80.227.2.4 I have my Time Capsule / Router in Bridge-Mode which means I am limited to the 5 devices and cannot use Guest Networks etc. What I've tried today. Static IPs: On all devices, I went from DHCP to Static and put in the same information when they had connected using DHCP. Somewhat surprisingly this did not work. None of the devices enjoyed any connection to the router and certainly no internet connection. Intentional Double-NAT - Time Capsule to 'DHCP and NAT': By selecting DHCP and NAT on my Router I was able to connect devices to my Time Capsule in the range 10.0.1.2 to 10.0.1.200. This offered no internet connectivity and didn't really help the situation. In this mode, however, I was able to force the devices - individually and laboriously - to look for the Router and previously listed DNSs by inputting the numbers from 'Bridge-mode' into the STATIC settings and then resetting the connection. The Router then appeared to assign a distinct IP address to the device and it worked on the network. I had this working for more than 5 devices. However, this is not a great solution because as soon as one of the mobile devices left the building it needed repointing to the Router. The connections were also not very stable. Especially when trying to hold onto a VPN. Spoofing a few MAC addresses: I'm afraid I don't really know what this would achieve, nor how to do it on an Apple device… So … I'm almost back at Square One. I have had to withdraw to the Bridge-Mode position again with the 5 device limit to see if there's a better course of action to follow. ANY help would be much appreciated. I am positive that I cannot be the only one suffering under this 5 device limit!

  Read the article

• Print directly to CUPS server from non-local clients (Ubuntu 14.04)

  - by OEP

  I set up a CUPS server with a few queues and printing from local clients (the CUPS test page and Samba) seems to work just fine. It seems like the CUPS server is denying non-local clients though: 130.127.48.70 - - [03/Jun/2014:14:29:19 -0400] "POST /printers/m137 HTTP/1.1" 200 390 Validate-Job successful-ok 130.127.48.70 - - [03/Jun/2014:14:29:19 -0400] "POST /printers/m137 HTTP/1.1" 200 339 Create-Job client-error-not-authorized localhost - - [03/Jun/2014:14:40:50 -0400] "POST /printers/m137 HTTP/1.1" 200 410869 Print-Job successful-ok This makes me think I have some sort of host-based restriction in my configuration file, but I can't find it. I've even set my default policy to Allow all only to get the same log message. I'm working from a configuration file which had previously worked on an older version of CUPS, which looks quite similar to the example cupsd.conf. I could be wrong but it looks like that final <Limit All> block ought to allow the actions the logs complain about. MaxLogSize 2000000000 # Log general information in error_log - change "info" to "debug" for # troubleshooting... LogLevel info #AccessLog syslog #ErrorLog syslog #PageLog syslog # Administrator user group... SystemGroup sys root lp # Only listen for connections from the local machine. Listen 0.0.0.0:631 Listen :::631 Listen /var/run/cups/cups.sock ServerName <snipped> # Show shared printers on the local network. Browsing Off BrowseOrder allow,deny # (Change '@LOCAL' to 'ALL' if using directed broadcasts from another subnet.) BrowseAllow @LOCAL # Default authentication type, when authentication is required... DefaultAuthType Basic # Restrict access to the server... <Location /> Order allow,deny Allow all </Location> # Restrict access to the admin pages... <Location /admin> AuthType Default Require user @SYSTEM Encryption Required Order allow,deny Allow all </Location> # Restrict access to configuration files... <Location /admin/conf> AuthType Default Require user @SYSTEM Encryption Required Order allow,deny Allow all </Location> # Set the default printer/job policies... <Policy default> # Job-related operations must be done by the owner or an administrator... <Limit Send-Document Send-URI Hold-Job Release-Job Restart-Job Purge-Jobs Set-Job-Attributes Create-Job-Subscription Renew-Subscription Cancel-Subscription Get-Notifications Reprocess-Job Cancel-Current-Job Suspend-Current-Job Resume-Job CUPS-Move-Job> Require user @OWNER @SYSTEM Order deny,allow </Limit> # All administration operations require an administrator to authenticate... <Limit CUPS-Add-Modify-Printer CUPS-Delete-Printer CUPS-Add-Modify-Class CUPS-Delete-Class CUPS-Set-Default> AuthType Default Require user @SYSTEM Order deny,allow </Limit> # All printer operations require a printer operator to authenticate... <Limit Pause-Printer Resume-Printer Enable-Printer Disable-Printer Pause-Printer-After-Current-Job Hold-New-Jobs Release-Held-New-Jobs Deactivate-Printer Activate-Printer Restart-Printer Shutdown-Printer Startup-Printer Promote-Job Schedule-Job-After CUPS-Accept-Jobs CUPS-Reject-Jobs> AuthType Default Require user @SYSTEM Order deny,allow </Limit> # Only the owner or an administrator can cancel or authenticate a job... <Limit Cancel-Job CUPS-Authenticate-Job> Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit All> Order allow,deny </Limit> </Policy>

  Read the article

• how to remove obsolete device and network entries? Device manager "uninstall" option has no effect

  - by Gizmo

  I am trying to remove a few "obsolete" things which annoy me (because I like to have everything cleen, working and not interferring with each other, fresh, etc..). I tried looking for solutions without any help, so here I am to ask. My first part is about removing obsolete networks, let me explain by showing the ipconfig output: C:\windows\system32>ipconfig Windows IP Configuration Wireless LAN adapter Local Area Connection* 11: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Local Area Connection* 9: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Ethernet adapter LAN: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wi-Fi: Connection-specific DNS Suffix . : home Link-local IPv6 Address . . . . . : fe80::c129:8d57:bbd1:3564%10 IPv4 Address. . . . . . . . . . . : 192.168.2.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.2.254 Tunnel adapter isatap.home: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : home C:\windows\system32> Specificalyy the first two adapter entries annoy me because the adapters are not visible in the network connection menu (invisible folder / file visibility set to "show"): And here is the second problem altogether with the first one: No matter what I click/do, Uninstall option has no effect on the multiplexor driver. (bridging stuff, right?) I really want to remove the Wireless LAN adapter Local Area Connection entries and the adapter multiplexor stuff but it's impossible? Why is this? How can I remove them anyway?

  Read the article

• Using pfSense, OpenVPN Connects but Still Can't See the Network

  - by nicorellius

  I am having an OpenVPN issue. I have a pfSense box at home configured to allow traffic through a VPN tunnel. The client computer is Windows XP Home, behind a standard Comcast connection and a Netgear wireless router. I use OpenVPN to access my work network (from where I am trying to get out of in this post) from home (with an XP Pro machine behind pfSense), and this works fine. The client config is similar but has the changes specific to my setup... Here is my XP Home config: client dev tun proto tcp remote pfsense.*.org 1194 (starred out by me) resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client.crt key client.key ns-cert-type server comp-lzo verb 3 When I launch the OpenVPN GUI, the Tunnel TAP network connection turns red, and I can right-click that to connect to the server. Everything seems to work fine until I browse for the actual network. The Tunnel TAP connection turns green and it says connected to 10.1.1.6 (I have tried different IP pools here too with no luck). I can see the internal network fine, but my home network behind pfSense is not there. I have tried browsing there by using Tools Map Network Drive, using the browser, with no success. When I open the command line on the client and use the ipconfig -all command, I get the following: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : TAP-Win32 Adapter V9 Physical Address. . . . . . . . . : *** (starred out by me) Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 10.1.1.6 Subnet Mask . . . . . . . . . . . : 255.255.255.252 Default Gateway . . . . . . . . . : DHCP Server . . . . . . . . . . . : 10.1.1.5 Lease Obtained. . . . . . . . . . : Monday, March 15, 2010 1:18:37 PM Lease Expires . . . . . . . . . . : Tuesday, March 15, 2011 1:18:37 PM I noticed that the default gateway is not present. Could this be my problem? I am still relatively new to firewalls, VPN, and network configuration so I'm sure I am messing up something simple. Oh yah, I should note that I have firewall rules configured for pfSense to allow traffic through the WAN and the LAN. At first there was just the WAN firewall rule, because that is what I got from the literature I was reading. I then created a LAN rule as well, but I'm not sure if this was correct. Neither way works, though. Screen shots below: Any help is much appreciated.

  Read the article

• Setting up a VPN connection to Amazon VPC - routing

  - by Keeno

  I am having some real issues setting up a VPN between out office and AWS VPC. The "tunnels" appear to be up, however I don't know if they are configured correctly. The device I am using is a Netgear VPN Firewall - FVS336GV2 If you see in the attached config downloaded from VPC (#3 Tunnel Interface Configuration), it gives me some "inside" addresses for the tunnel. When setting up the IPsec tunnels do I use the inside tunnel IP's (e.g. 169.254.254.2/30) or do I use my internal network subnet (10.1.1.0/24) I have tried both, when I tried the local network (10.1.1.x) the tracert stops at the router. When I tried with the "inside" ips, the tracert to the amazon VPC (10.0.0.x) goes out over the internet. this all leads me to the next question, for this router, how do I set up stage #4, the static next hop? What are these seemingly random "inside" addresses and where did amazon generate them from? 169.254.254.x seems odd? With a device like this, is the VPN behind the firewall? I have tweaked any IP addresses below so that they are not "real". I am fully aware, this is probably badly worded. Please if there is any further info/screenshots that will help, let me know. Amazon Web Services Virtual Private Cloud IPSec Tunnel #1 ================================================================================ #1: Internet Key Exchange Configuration Configure the IKE SA as follows - Authentication Method : Pre-Shared Key - Pre-Shared Key : --- - Authentication Algorithm : sha1 - Encryption Algorithm : aes-128-cbc - Lifetime : 28800 seconds - Phase 1 Negotiation Mode : main - Perfect Forward Secrecy : Diffie-Hellman Group 2 #2: IPSec Configuration Configure the IPSec SA as follows: - Protocol : esp - Authentication Algorithm : hmac-sha1-96 - Encryption Algorithm : aes-128-cbc - Lifetime : 3600 seconds - Mode : tunnel - Perfect Forward Secrecy : Diffie-Hellman Group 2 IPSec Dead Peer Detection (DPD) will be enabled on the AWS Endpoint. We recommend configuring DPD on your endpoint as follows: - DPD Interval : 10 - DPD Retries : 3 IPSec ESP (Encapsulating Security Payload) inserts additional headers to transmit packets. These headers require additional space, which reduces the amount of space available to transmit application data. To limit the impact of this behavior, we recommend the following configuration on your Customer Gateway: - TCP MSS Adjustment : 1387 bytes - Clear Don't Fragment Bit : enabled - Fragmentation : Before encryption #3: Tunnel Interface Configuration Your Customer Gateway must be configured with a tunnel interface that is associated with the IPSec tunnel. All traffic transmitted to the tunnel interface is encrypted and transmitted to the Virtual Private Gateway. The Customer Gateway and Virtual Private Gateway each have two addresses that relate to this IPSec tunnel. Each contains an outside address, upon which encrypted traffic is exchanged. Each also contain an inside address associated with the tunnel interface. The Customer Gateway outside IP address was provided when the Customer Gateway was created. Changing the IP address requires the creation of a new Customer Gateway. The Customer Gateway inside IP address should be configured on your tunnel interface. Outside IP Addresses: - Customer Gateway : 217.33.22.33 - Virtual Private Gateway : 87.222.33.42 Inside IP Addresses - Customer Gateway : 169.254.254.2/30 - Virtual Private Gateway : 169.254.254.1/30 Configure your tunnel to fragment at the optimal size: - Tunnel interface MTU : 1436 bytes #4: Static Routing Configuration: To route traffic between your internal network and your VPC, you will need a static route added to your router. Static Route Configuration Options: - Next hop : 169.254.254.1 You should add static routes towards your internal network on the VGW. The VGW will then send traffic towards your internal network over the tunnels. IPSec Tunnel #2 ================================================================================ #1: Internet Key Exchange Configuration Configure the IKE SA as follows - Authentication Method : Pre-Shared Key - Pre-Shared Key : --- - Authentication Algorithm : sha1 - Encryption Algorithm : aes-128-cbc - Lifetime : 28800 seconds - Phase 1 Negotiation Mode : main - Perfect Forward Secrecy : Diffie-Hellman Group 2 #2: IPSec Configuration Configure the IPSec SA as follows: - Protocol : esp - Authentication Algorithm : hmac-sha1-96 - Encryption Algorithm : aes-128-cbc - Lifetime : 3600 seconds - Mode : tunnel - Perfect Forward Secrecy : Diffie-Hellman Group 2 IPSec Dead Peer Detection (DPD) will be enabled on the AWS Endpoint. We recommend configuring DPD on your endpoint as follows: - DPD Interval : 10 - DPD Retries : 3 IPSec ESP (Encapsulating Security Payload) inserts additional headers to transmit packets. These headers require additional space, which reduces the amount of space available to transmit application data. To limit the impact of this behavior, we recommend the following configuration on your Customer Gateway: - TCP MSS Adjustment : 1387 bytes - Clear Don't Fragment Bit : enabled - Fragmentation : Before encryption #3: Tunnel Interface Configuration Outside IP Addresses: - Customer Gateway : 217.33.22.33 - Virtual Private Gateway : 87.222.33.46 Inside IP Addresses - Customer Gateway : 169.254.254.6/30 - Virtual Private Gateway : 169.254.254.5/30 Configure your tunnel to fragment at the optimal size: - Tunnel interface MTU : 1436 bytes #4: Static Routing Configuration: Static Route Configuration Options: - Next hop : 169.254.254.5 You should add static routes towards your internal network on the VGW. The VGW will then send traffic towards your internal network over the tunnels. EDIT #1 After writing this post, I continued to fiddle and something started to work, just not very reliably. The local IPs to use when setting up the tunnels where indeed my network subnets. Which further confuses me over what these "inside" IP addresses are for. The problem is, results are not consistent what so ever. I can "sometimes" ping, I can "sometimes" RDP using the VPN. Sometimes, Tunnel 1 or Tunnel 2 can be up or down. When I came back into work today, Tunnel 1 was down, so I deleted it and re-created it from scratch. Now I cant ping anything, but Amazon AND the router are telling me tunnel 1/2 are fine. I guess the router/vpn hardware I have just isnt up to the job..... EDIT #2 Now Tunnel 1 is up, Tunnel 2 is down (I didn't change any settings) and I can ping/rdp again. EDIT #3 Screenshot of route table that the router has built up. Current state (tunnel 1 still up and going string, 2 is still down and wont re-connect)

  Read the article

• Poor upload/download speed on 2 x ADSL lines into a Cisco 2621XM

  - by 2020mobile

  Hi, Sorry never been on this site before so I apologise if not the right section or even forum. I have users complaining of very slow internetn connectivity on site and have checked with our ISP who have said that the line is testing at 8mb. We have 2 x BT lines that have our ISP broadand on them. Both lines go into a Cisco 2600 series router that then has a PIX firewall off that. Connectivity is successful just gone really slow and unable to download anything. Config is below: version 12.3 no service pad service tcp-keepalives-in service tcp-keepalives-out service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname ROUTER-ADSL-INTERNET ! logging buffered 16384 informational enable secret xxx enable password xxx ! username xxx username xxx clock summer-time UK recurring last Sun Mar 1:00 last Sun Oct 1:00 aaa new-model ! ! aaa authentication login default local aaa authorization exec default local aaa session-id common ip subnet-zero no ip source-route ! ! ! ip audit notify log ip audit po max-events 100 no ip bootp server ip name-server 213.208.106.212 no mpls ldp logging neighbor-changes no ftp-server write-enable ! ! ! ! ! ! ! ! ! ! no voice hpi capture buffer no voice hpi capture destination ! ! ! ! ! ! ! ! interface ATM0/0 description 01270 111111 no ip address no atm ilmi-keepalive pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 ! dsl operating-mode auto ! interface FastEthernet0/0 ip address 82.133.32.9 255.255.255.248 shutdown speed 100 full-duplex no cdp enable ! interface ATM0/1 description 01270 222222 no ip address no atm ilmi-keepalive pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 ! dsl operating-mode auto ! interface FastEthernet0/1 ip address 217.146.115.49 255.255.255.240 duplex auto speed auto no cdp enable ! interface Dialer0 ip address 217.146.115.250 255.255.255.248 encapsulation ppp dialer pool 1 dialer-group 1 ppp authentication chap callin ppp chap hostname [email protected] ppp chap password 7 xxxxx ppp multilink ! ip classless ip route 0.0.0.0 0.0.0.0 Dialer0 ! no ip http server no ip http secure-server ! no logging trap access-list 10 permit 217.146.115.50 access-list 10 permit 82.133.32.10 access-list 10 deny any access-list 22 permit 217.146.115.50 access-list 22 permit 217.206.239.86 access-list 22 permit 82.133.32.10 access-list 22 deny any dialer-list 1 protocol ip permit no cdp run ! ! snmp-server community xxxxxx RO 10 snmp-server enable traps tty radius-server authorization permit missing Service-Type ! ! ! ! ! ! line con 0 exec-timeout 5 0 password 7 xxxxxx line aux 0 no exec line vty 0 4 access-class 22 in exec-timeout 5 0 password 7 xxxxxx transport input telnet ssh transport output none line vty 5 15 password 7 xxxxxx transport input telnet ssh ! ntp clock-period 17180095 ntp server 130.88.200.98 ! ! end Now my knowledge is very limited but ISP have said that while the lines are bonded each needs a seperate login as they've recently changed their L2TP router and that enforces the use of seperate logins - when the lines were configured we were given two logins. So, my question is what changes do I need to make to the config in order to get this working? it was ok before their change and I do have another login :- 01270 111111 - [email protected] 01270 222222 - [email protected] Apologies for the long email and thanks for taking the time to read it. Any more info I can provide please let me know. Thanks,

  Read the article

• OpenVPN on Ubuntu 11.10 - unable to redirect default gateway

  - by Vladimir Kadalashvili

  I'm trying to connect to connect to OpenVPN server from my Ubuntu 11.10 machine. I use the following command to do it (under root user): openvpn --config /home/vladimir/client.ovpn Everything seems to be OK, it connects normally without any warnings and errors, but when I try to browse the internet I see that I still use my own IP address, so VPN connection doesn't work. When I run openvpn command, it displays the following message among others: NOTE: unable to redirect default gateway -- Cannot read current default gateway from system I think it's the cause of this problem, but unfortunately I don't know how to fix it. Below is full output of openvpn command: Sat Jun 9 23:51:36 2012 OpenVPN 2.2.0 x86_64-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [eurephia] [MH] [PF_INET6] [IPv6 payload 20110424-2 (2.2RC2)] built on Jul 4 2011 Sat Jun 9 23:51:36 2012 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Sat Jun 9 23:51:36 2012 Control Channel Authentication: tls-auth using INLINE static key file Sat Jun 9 23:51:36 2012 Outgoing Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Sat Jun 9 23:51:36 2012 Incoming Control Channel Authentication: Using 160 bit message hash 'SHA1' for HMAC authentication Sat Jun 9 23:51:36 2012 LZO compression initialized Sat Jun 9 23:51:36 2012 Control Channel MTU parms [ L:1542 D:166 EF:66 EB:0 ET:0 EL:0 ] Sat Jun 9 23:51:36 2012 Socket Buffers: R=[126976->200000] S=[126976->200000] Sat Jun 9 23:51:36 2012 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Sat Jun 9 23:51:36 2012 Local Options hash (VER=V4): '504e774e' Sat Jun 9 23:51:36 2012 Expected Remote Options hash (VER=V4): '14168603' Sat Jun 9 23:51:36 2012 UDPv4 link local: [undef] Sat Jun 9 23:51:36 2012 UDPv4 link remote: [AF_INET]94.229.78.130:1194 Sat Jun 9 23:51:37 2012 TLS: Initial packet from [AF_INET]94.229.78.130:1194, sid=13fd921b b42072ab Sat Jun 9 23:51:37 2012 VERIFY OK: depth=1, /CN=OpenVPN_CA Sat Jun 9 23:51:37 2012 VERIFY OK: nsCertType=SERVER Sat Jun 9 23:51:37 2012 VERIFY OK: depth=0, /CN=OpenVPN_Server Sat Jun 9 23:51:38 2012 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Sat Jun 9 23:51:38 2012 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Sat Jun 9 23:51:38 2012 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Sat Jun 9 23:51:38 2012 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Sat Jun 9 23:51:38 2012 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Sat Jun 9 23:51:38 2012 [OpenVPN_Server] Peer Connection Initiated with [AF_INET]94.229.78.130:1194 Sat Jun 9 23:51:40 2012 SENT CONTROL [OpenVPN_Server]: 'PUSH_REQUEST' (status=1) Sat Jun 9 23:51:40 2012 PUSH: Received control message: 'PUSH_REPLY,explicit-exit-notify,topology subnet,route-delay 5 30,dhcp-pre-release,dhcp-renew,dhcp-release,route-metric 101,ping 5,ping-restart 40,redirect-gateway def1,redirect-gateway bypass-dhcp,redirect-gateway autolocal,route-gateway 5.5.0.1,dhcp-option DNS 8.8.8.8,dhcp-option DNS 8.8.4.4,register-dns,comp-lzo yes,ifconfig 5.5.117.43 255.255.0.0' Sat Jun 9 23:51:40 2012 Unrecognized option or missing parameter(s) in [PUSH-OPTIONS]:4: dhcp-pre-release (2.2.0) Sat Jun 9 23:51:40 2012 Unrecognized option or missing parameter(s) in [PUSH-OPTIONS]:5: dhcp-renew (2.2.0) Sat Jun 9 23:51:40 2012 Unrecognized option or missing parameter(s) in [PUSH-OPTIONS]:6: dhcp-release (2.2.0) Sat Jun 9 23:51:40 2012 Unrecognized option or missing parameter(s) in [PUSH-OPTIONS]:16: register-dns (2.2.0) Sat Jun 9 23:51:40 2012 OPTIONS IMPORT: timers and/or timeouts modified Sat Jun 9 23:51:40 2012 OPTIONS IMPORT: explicit notify parm(s) modified Sat Jun 9 23:51:40 2012 OPTIONS IMPORT: LZO parms modified Sat Jun 9 23:51:40 2012 OPTIONS IMPORT: --ifconfig/up options modified Sat Jun 9 23:51:40 2012 OPTIONS IMPORT: route options modified Sat Jun 9 23:51:40 2012 OPTIONS IMPORT: route-related options modified Sat Jun 9 23:51:40 2012 OPTIONS IMPORT: --ip-win32 and/or --dhcp-option options modified Sat Jun 9 23:51:40 2012 ROUTE: default_gateway=UNDEF Sat Jun 9 23:51:40 2012 TUN/TAP device tun0 opened Sat Jun 9 23:51:40 2012 TUN/TAP TX queue length set to 100 Sat Jun 9 23:51:40 2012 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0 Sat Jun 9 23:51:40 2012 /sbin/ifconfig tun0 5.5.117.43 netmask 255.255.0.0 mtu 1500 broadcast 5.5.255.255 Sat Jun 9 23:51:45 2012 NOTE: unable to redirect default gateway -- Cannot read current default gateway from system Sat Jun 9 23:51:45 2012 Initialization Sequence Completed Output of route command: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default * 0.0.0.0 U 0 0 0 ppp0 5.5.0.0 * 255.255.0.0 U 0 0 0 tun0 link-local * 255.255.0.0 U 1000 0 0 wlan0 192.168.0.0 * 255.255.255.0 U 0 0 0 wlan0 stream-ts1.net. * 255.255.255.255 UH 0 0 0 ppp0 Output of ifconfig command: eth0 Link encap:Ethernet HWaddr 6c:62:6d:44:0d:12 inet6 addr: fe80::6e62:6dff:fe44:d12/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:54594 errors:0 dropped:0 overruns:0 frame:0 TX packets:59897 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:44922107 (44.9 MB) TX bytes:8839969 (8.8 MB) Interrupt:41 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4561 errors:0 dropped:0 overruns:0 frame:0 TX packets:4561 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:685425 (685.4 KB) TX bytes:685425 (685.4 KB) ppp0 Link encap:Point-to-Point Protocol inet addr:213.206.63.44 P-t-P:213.206.34.4 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 RX packets:53577 errors:0 dropped:0 overruns:0 frame:0 TX packets:58892 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:43667387 (43.6 MB) TX bytes:7504776 (7.5 MB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:5.5.117.43 P-t-P:5.5.117.43 Mask:255.255.0.0 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 00:27:19:f6:b5:cf inet addr:192.168.0.1 Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::227:19ff:fef6:b5cf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12079 errors:0 dropped:0 overruns:0 frame:0 TX packets:11178 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1483691 (1.4 MB) TX bytes:4307899 (4.3 MB) So my question is - how to make OpenVPN redirect default gateway? Thanks!

  Read the article

• Dynamic DNS registration for VPN clients

  - by Eric Falsken

  I've got a VPN server set up in my Active Directory on a remote network. (VPN Server is separate box from DNS/AD) When I dial into the network (client machine is not a member of the AD) the machine does not register its IP or Hostname in the DNS. I've played with all possible combinations of DHCP and RRAS-allocated IP pools, and none of them seem to cause my client to register. Is it because my client has to be a member of the domain? Are there some security settins I can tweak so that it can register its hostname/ip? I've looked in the event logs (System and Security) for the AD, DNS, DHCP, RRAS, and the client machine, and don't see anything relating to DNS Registration. Here's the IPConfig on the client machine (once connected): PPP adapter My VPN Name: Connection-specific DNS Suffix . : mydomain.local Description . . . . . . . . . . . : My VPN Name Physical Address. . . . . . . . . : DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.1.22(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.1.52 <- DC1 192.168.1.53 <- DC2 NetBIOS over Tcpip. . . . . . . . : Enabled Edit: It looks like my clients are not recieving the DHCP Scoope Options. I found this great article in Microsoft's KB. So the problem here is that the VPN Server "pre-reserves" the DHCP addresses, but then you have to add the DHCP Relay Agent to relay the secondary request for scope options. My problem is that the DHCP Relay Agent isn't relaying to the local DHCP server (same box as the VPN/RRAS). I've configured the DHCP Relay Agent according to this KB, but it dosn't work for a local DHCP server. (I see the request count increasing, but no responses) I was able to get everything working by specifying the DNS server and domain name in the VPN connection properties on the client. But am still unable to assign it (or the default gateway) dynamically via DHCP. The client also has to be a member of the remote domain.

  Read the article

• Network traffic is not being forwarded from a VM to the network using a bridged interface with Xen + libvirt

  - by foob

  I'm having trouble getting network access from a VM that I'm running using Xen and libvirt. I've been trying different things and reading similar posts online for a couple of days but I'm really stuck at this point. If anybody could offer some insight it would be much appreciated. I have a VM that I'm running on a host with a bridge set up as br0 and an interface eth0 on a 192.168.60.0/24 subnet. The networking portion of the libvirt configuration xml is: <interface type='bridge'> <mac address='ff:a0:d1:e5:07:de'/> <source bridge='br0'/> <script path='/etc/xen/scripts/vif-bridge'/> <model type='virtio' /> </interface> When I start the VM a vif6.0 interface is created on the host and the ifconfig output is: br0 Link encap:Ethernet HWaddr 00:A0:D1:C3:07:DE inet addr:192.168.60.33 Bcast:192.168.60.255 Mask:255.255.255.0 inet6 addr: fe80::2a0:d1ff:fee5:7de/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13 errors:0 dropped:0 overruns:0 frame:0 TX packets:40 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:3570 (3.4 KiB) TX bytes:3508 (3.4 KiB) eth0 Link encap:Ethernet HWaddr 00:A0:D1:C3:07:DE inet6 addr: fe80::2a0:d1ff:fee5:7de/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:492 (492.0 b) Interrupt:19 Memory:fe8f0000-fe900000 vif6.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:80 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:6660 (6.5 KiB) TX bytes:468 (468.0 b) virbr0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) The 'brctl show' output seems to show the bridge being configured correctly: br0 8000.00a0d1e507de no eth0 vif6.0 The ifcfg-eth0 contents in the VM are: DEVICE=eth0 BOOTPROTO=static HWADDR=FF:A0:D1:E5:07:DE IPADDR=192.168.60.133 NETMASK=255.255.255.0 ONBOOT=yes and the output of ifconfig in the VM look like what I would expect: eth0 Link encap:Ethernet HWaddr FF:A0:D1:E5:07:DE inet addr:192.168.60.133 Bcast:192.168.60.255 Mask:255.255.255.0 inet6 addr: fe80::fda0:d1ff:fee5:7de/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6 errors:0 dropped:0 overruns:0 frame:0 TX packets:80 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:468 (468.0 b) TX bytes:7780 (7.5 KiB) but when I try to ssh or ping another computer I get 'no route to host.' Using tcpdump on the host system I tried to see if I could narrow down where the problem is: # tcpdump -vv -i vif6.0 tcpdump: WARNING: vif6.0: no IPv4 address assigned tcpdump: listening on vif6.0, link-type EN10MB (Ethernet), capture size 96 bytes 14:49:40.833997 arp who-has 192.168.60.35 tell 192.168.60.133 14:49:41.833314 arp who-has 192.168.60.35 tell 192.168.60.133 14:49:42.833309 arp who-has 192.168.60.35 tell 192.168.60.133 So the VM is sending out out an arp who-has packet when I try to ssh to 192.168.60.35. I think that this means the setup within the VM is ok and that this is an issue on the host system. If I run tcpdump with the interface of br0 then I don't see these arp packets. My thought here is that the packets are being blocked before going on to the bridge somehow. I tried adding an iptables rule to resolve this: -A FORWARD -m physdev --physdev-is-bridged -j ACCEPT but it didn't work. I also tried the following: /sbin/sysctl -w net.bridge.bridge-nf-call-ip6tables=0 /sbin/sysctl -w net.bridge.bridge-nf-call-iptables=0 /sbin/sysctl -w net.bridge.bridge-nf-call-arptables=0 /sbin/sysctl -w net.ipv4.ip_forward=1 which had no impact. Is it obvious to somebody who has more experience than me what I'm missing here? Should vif6.0 have the same MAC address is eth0 in the vm? Do I need more rules in my iptables? Thanks for any help!

  Read the article

• KVM/Libvirt bridged/routed networking not working on newer guest kernels

  - by SharkWipf

  I have a dedicated server running Debian 6, with Libvirt (0.9.11.3) and Qemu-KVM (qemu-kvm-1.0+dfsg-11, Debian). I am having a problem getting bridged/routed networking to work in KVM guests with newer kernels (2.6.38). NATted networking works fine though. Older kernels work perfectly fine as well. The host kernel is at version 3.2.0-2-amd64, the problem was also there on an older host kernel. The contents of the host's /etc/network/interfaces (ip removed): # Loopback device: auto lo iface lo inet loopback # bridge auto br0 iface br0 inet static address 176.9.xx.xx broadcast 176.9.xx.xx netmask 255.255.255.224 gateway 176.9.xx.xx pointopoint 176.9.xx.xx bridge_ports eth0 bridge_stp off bridge_maxwait 0 bridge_fd 0 up route add -host 176.9.xx.xx dev br0 # VM IP post-up mii-tool -F 100baseTx-FD br0 # default route to access subnet up route add -net 176.9.xx.xx netmask 255.255.255.224 gw 176.9.xx.xx br0 The output of ifconfig -a on the host: br0 Link encap:Ethernet HWaddr 54:04:a6:8a:66:13 inet addr:176.9.xx.xx Bcast:176.9.xx.xx Mask:255.255.255.224 inet6 addr: fe80::5604:a6ff:fe8a:6613/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:20216729 errors:0 dropped:0 overruns:0 frame:0 TX packets:19962220 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:14144528601 (13.1 GiB) TX bytes:7990702656 (7.4 GiB) eth0 Link encap:Ethernet HWaddr 54:04:a6:8a:66:13 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:26991788 errors:0 dropped:12066 overruns:0 frame:0 TX packets:19737261 errors:270082 dropped:0 overruns:0 carrier:270082 collisions:1686317 txqueuelen:1000 RX bytes:15459970915 (14.3 GiB) TX bytes:6661808415 (6.2 GiB) Interrupt:17 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:6240133 errors:0 dropped:0 overruns:0 frame:0 TX packets:6240133 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6081956230 (5.6 GiB) TX bytes:6081956230 (5.6 GiB) virbr0 Link encap:Ethernet HWaddr 52:54:00:79:e4:5a inet addr:192.168.100.1 Bcast:192.168.100.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:225016 errors:0 dropped:0 overruns:0 frame:0 TX packets:412958 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:16284276 (15.5 MiB) TX bytes:687827984 (655.9 MiB) virbr0-nic Link encap:Ethernet HWaddr 52:54:00:79:e4:5a BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) vnet0 Link encap:Ethernet HWaddr fe:54:00:93:4e:68 inet6 addr: fe80::fc54:ff:fe93:4e68/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:607670 errors:0 dropped:0 overruns:0 frame:0 TX packets:5932089 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:83574773 (79.7 MiB) TX bytes:1092482370 (1.0 GiB) vnet1 Link encap:Ethernet HWaddr fe:54:00:ed:6a:43 inet6 addr: fe80::fc54:ff:feed:6a43/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:922132 errors:0 dropped:0 overruns:0 frame:0 TX packets:6342375 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:251091242 (239.4 MiB) TX bytes:1629079567 (1.5 GiB) vnet2 Link encap:Ethernet HWaddr fe:54:00:0d:cb:3d inet6 addr: fe80::fc54:ff:fe0d:cb3d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:9461 errors:0 dropped:0 overruns:0 frame:0 TX packets:665189 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:4990275 (4.7 MiB) TX bytes:49229647 (46.9 MiB) vnet3 Link encap:Ethernet HWaddr fe:54:cd:83:eb:aa inet6 addr: fe80::fc54:cdff:fe83:ebaa/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1649 errors:0 dropped:0 overruns:0 frame:0 TX packets:12177 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:77233 (75.4 KiB) TX bytes:2127934 (2.0 MiB) The guest's /etc/network/interfaces, in this case running Ubuntu 12.04 (ip removed): # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 176.9.xx.xx netmask 255.255.255.248 gateway 176.9.xx.xx # Host IP pointopoint 176.9.xx.xx # Host IP dns-nameservers 8.8.8.8 8.8.4.4 The output of ifconfig -a on the guest: eth0 Link encap:Ethernet HWaddr 52:54:cd:83:eb:aa inet addr:176.9.xx.xx Bcast:0.0.0.0 Mask:255.255.255.255 inet6 addr: fe80::5054:cdff:fe83:ebaa/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14190 errors:0 dropped:0 overruns:0 frame:0 TX packets:1768 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2614642 (2.6 MB) TX bytes:82700 (82.7 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:954 errors:0 dropped:0 overruns:0 frame:0 TX packets:954 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:176679 (176.6 KB) TX bytes:176679 (176.6 KB) Output of ping -c4 on the guest: PING google.nl (173.194.35.151) 56(84) bytes of data. 64 bytes from muc03s01-in-f23.1e100.net (173.194.35.151): icmp_req=1 ttl=55 time=14.7 ms From static.174.82.xx.xx.clients.your-server.de (176.9.xx.xx): icmp_seq=2 Redirect Host(New nexthop: static.161.82.9.176.clients.your-server.de (176.9.82.161)) 64 bytes from muc03s01-in-f23.1e100.net (173.194.35.151): icmp_req=2 ttl=55 time=15.1 ms From static.198.170.9.176.clients.your-server.de (176.9.170.198) icmp_seq=3 Destination Host Unreachable From static.198.170.9.176.clients.your-server.de (176.9.170.198) icmp_seq=4 Destination Host Unreachable --- google.nl ping statistics --- 4 packets transmitted, 2 received, +2 errors, 50% packet loss, time 3002ms rtt min/avg/max/mdev = 14.797/14.983/15.170/0.223 ms, pipe 2 The static.174.82.xx.xx.clients.your-server.de (176.9.xx.xx) is the host's IP. I have encountered this problem with every guest OS I've tried, that being Fedora, Ubuntu (server/desktop) and Debian with an upgraded kernel. I've also tried compiling the guest kernel myself, to no avail. I have no problem with recompiling a kernel, though the host cannot afford any downtime. Any ideas on this problem are very welcome. EDIT: I can ping the host from inside the guest.

  Read the article

• Exposing the AnyConnect HTTPS service to outside network

  - by Maciej Swic

  We have a Cisco ASA 5505 with firmware ASA9.0(1) and ASDM 7.0(2). It is configured with a public ip address, and when trying to reach it from the outside by HTTPS for AnyConnect VPN, we get the following log output: 6 Nov 12 2012 07:01:40 <client-ip> 51000 <asa-ip> 443 Built inbound TCP connection 2889 for outside:<client-ip>/51000 (<client-ip>/51000) to identity:<asa-ip>/443 (<asa-ip>/443) 6 Nov 12 2012 07:01:40 <client-ip> 50999 <asa-ip> 443 Built inbound TCP connection 2890 for outside:<client-ip>/50999 (<client-ip>/50999) to identity:<asa-ip>/443 (<asa-ip>/443) 6 Nov 12 2012 07:01:40 <client-ip> 51000 <asa-ip> 443 Teardown TCP connection 2889 for outside:<client-ip>/51000 to identity:<asa-ip>/443 duration 0:00:00 bytes 0 No valid adjacency 6 Nov 12 2012 07:01:40 <client-ip> 50999 <asa-ip> 443 Teardown TCP connection 2890 for outside:<client-ip>/50999 to identity:<asa-ip>/443 duration 0:00:00 bytes 0 No valid adjacency We finished the startup wizard and the anyconnect vpn wizard and here is the resulting configuration: Cryptochecksum: 12262d68 23b0d136 bb55644a 9c08f86b : Saved : Written by enable_15 at 07:08:30.519 UTC Mon Nov 12 2012 ! ASA Version 9.0(1) ! hostname vpn domain-name office.<redacted>.com enable password <redacted> encrypted passwd <redacted> encrypted names ip local pool vpn-pool 192.168.67.2-192.168.67.253 mask 255.255.255.0 ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.68.250 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address <redacted> 255.255.255.248 ! ftp mode passive dns server-group DefaultDNS domain-name office.<redacted>.com object network obj_any subnet 0.0.0.0 0.0.0.0 pager lines 24 logging enable logging asdm informational mtu outside 1500 mtu inside 1500 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 no arp permit-nonconnected ! object network obj_any nat (inside,outside) dynamic interface timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy user-identity default-domain LOCAL http server enable http 192.168.68.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart crypto ipsec ikev2 ipsec-proposal DES protocol esp encryption des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal 3DES protocol esp encryption 3des protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES protocol esp encryption aes protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES192 protocol esp encryption aes-192 protocol esp integrity sha-1 md5 crypto ipsec ikev2 ipsec-proposal AES256 protocol esp encryption aes-256 protocol esp integrity sha-1 md5 crypto ipsec security-association pmtu-aging infinite crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map inside_map interface inside crypto ca trustpoint _SmartCallHome_ServerCA crl configure crypto ca trustpoint ASDM_TrustPoint0 enrollment self subject-name CN=vpn proxy-ldc-issuer crl configure crypto ca trustpool policy crypto ca certificate chain _SmartCallHome_ServerCA certificate ca 6ecc7aa5a7032009b8cebcf4e952d491 <redacted> quit crypto ca certificate chain ASDM_TrustPoint0 certificate f678a050 <redacted> quit crypto ikev2 policy 1 encryption aes-256 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 10 encryption aes-192 integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 20 encryption aes integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 30 encryption 3des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 policy 40 encryption des integrity sha group 5 2 prf sha lifetime seconds 86400 crypto ikev2 enable outside client-services port 443 crypto ikev2 remote-access trustpoint ASDM_TrustPoint0 telnet timeout 5 ssh 192.168.68.0 255.255.255.0 inside ssh timeout 5 console timeout 0 vpn-addr-assign local reuse-delay 60 dhcpd auto_config outside ! dhcpd address 192.168.68.254-192.168.68.254 inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ssl trust-point ASDM_TrustPoint0 inside ssl trust-point ASDM_TrustPoint0 outside webvpn enable outside enable inside anyconnect image disk0:/anyconnect-win-3.1.01065-k9.pkg 1 anyconnect image disk0:/anyconnect-linux-3.1.01065-k9.pkg 2 anyconnect image disk0:/anyconnect-macosx-i386-3.1.01065-k9.pkg 3 anyconnect profiles GM-AnyConnect_client_profile disk0:/GM-AnyConnect_client_profile.xml anyconnect enable tunnel-group-list enable group-policy GroupPolicy_GM-AnyConnect internal group-policy GroupPolicy_GM-AnyConnect attributes wins-server none dns-server value 192.168.68.254 vpn-tunnel-protocol ikev2 ssl-client default-domain value office.<redacted>.com webvpn anyconnect profiles value GM-AnyConnect_client_profile type user username <redacted> password <redacted> encrypted tunnel-group GM-AnyConnect type remote-access tunnel-group GM-AnyConnect general-attributes address-pool vpn-pool default-group-policy GroupPolicy_GM-AnyConnect tunnel-group GM-AnyConnect webvpn-attributes group-alias GM-AnyConnect enable ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global prompt hostname context call-home reporting anonymous Cryptochecksum:12262d6823b0d136bb55644a9c08f86b : end Clearly we are missing something, but the question is, what?

  Read the article

• Gateway setting is empty

  - by Dodi Jones

  This laptop hasn't been used in almost a year. It connected to the internet just fine last time used. Now it can't get on line. ipconfig:The Gateway setting for this computer is empty. Make sure your access point is working properly. Microsoft Windows XP [Version 5.1.2600] (C) Copyright 1985-2001 Microsoft Corp. C:\Documents and Settings\Dodi>IPCONFIG /ALL Windows IP Configuration Host Name . . . . . . . . . . . . : 8A287A4ADEF0487 Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : Yes WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : LAN-Express AS IEEE 802.11g miniPCI Adapter Physical Address. . . . . . . . . : 00-14-A4-72-37-E1 Dhcp Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.0.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.1.1 Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Intel(R) PRO/100 VE Network Connection Physical Address. . . . . . . . . : 00-01-4A-EF-A8-7D How do I fix this?

  Read the article

• Other Ideas to troubleshoot Cisco IPSec VPN on OSX?

  - by Tawm

  We have one user running OSX Snow Leopard who is having issues staying connected to our VPN running off of an ASA5510. His connection can die even as he's actively pushing traffic across it or if he's been idle for a period of time. Other users on Snow Leopard, Lion, XP, Vista, 7 and various linux flavors are able to stay connected for 24hrs+ without issue We've deleted and remade the connection in System Preferences Networking, ran killall racoon (kills any lingering connections) Below are the logs from the user's system.log from a connect/disconnect cycle: Oct 10 21:22:25 username racoon[8192]: Connecting. Oct 10 21:22:25 username racoon[8192]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Oct 10 21:22:25 username racoon[8192]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Oct 10 21:22:25 username racoon[8192]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Oct 10 21:22:25 username racoon[8192]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Oct 10 21:22:25 username racoon[8192]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Oct 10 21:22:29 username racoon[8192]: IKE Packet: transmit success. (Mode-Config message). Oct 10 21:22:29 username racoon[8192]: IKEv1 XAUTH: success. (XAUTH Status is OK). Oct 10 21:22:29 username racoon[8192]: IKE Packet: transmit success. (Mode-Config message). Oct 10 21:22:29 username racoon[8192]: IKEv1 Config: retransmited. (Mode-Config retransmit). Oct 10 21:22:29 username racoon[8192]: IKE Packet: receive success. (MODE-Config). Oct 10 21:22:29 username configd[14]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.0.100), current interface setting (name: utun0, family: 1001, address: 10.215.8.53, subnet: 255.0.0.0, destination: 10.215.8.53). Oct 10 21:22:29 username racoon[8192]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). Oct 10 21:22:29 username configd[14]: network configuration changed. Oct 10 21:22:29 username racoon[8192]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). Oct 10 21:22:29 username racoon[8192]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). Oct 10 21:22:29 username racoon[8192]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode). Oct 10 21:22:29 username racoon[8192]: Connected. Oct 10 21:22:29 username configd[14]: SCNCController: Connected. Oct 10 21:22:29 username racoon[8192]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). Oct 10 21:22:29 username racoon[8192]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). Oct 10 21:22:29 username racoon[8192]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). Oct 10 21:22:29 username racoon[8192]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode). Oct 10 21:22:47 username login[8200]: USER_PROCESS: 8200 ttys003 Oct 10 21:22:48 username GrowlHelperApp[160]: Periodic CFURLCache Insert stats (iters: 17240) - Tx time:0.001749, # of Inserts: 1, # of bytes written: 304, Did shrink: NO, Size of cache-file: 26624, Num of Failures: 0 Oct 10 21:25:24 username login[7367]: DEAD_PROCESS: 7367 ttys002 Oct 10 21:25:31 username login[7907]: DEAD_PROCESS: 7907 ttys001 Oct 10 21:27:32 username configd[14]: SCNCController: Disconnecting. (Connection was up for, 303 seconds). Oct 10 21:27:32 username racoon[8192]: IKE Packet: transmit success. (Information message). Oct 10 21:27:32 username racoon[8192]: IKEv1 Information-Notice: transmit success. (Delete IPSEC-SA). Oct 10 21:27:32 username racoon[8192]: IKE Packet: transmit success. (Information message). Oct 10 21:27:32 username racoon[8192]: IKEv1 Information-Notice: transmit success. (Delete IPSEC-SA). Oct 10 21:27:32 username racoon[8192]: IKE Packet: transmit success. (Information message). Oct 10 21:27:32 username racoon[8192]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). Oct 10 21:27:32 username racoon[8192]: Disconnecting. (Connection was up for, 302.766105 seconds). Oct 10 21:27:32 username configd[14]: network configuration changed. Oct 10 21:27:34 username login[8200]: DEAD_PROCESS: 8200 ttys003

  Read the article

• With dnsmasq as the DNS server, 'dig' and 'ping' succeed while 'nslookup' fails

  - by einpoklum

  I installed dnsmasq on a machine of mine (It's a Kubuntu 12.04 LTS), backed only by /etc/hosts (no connection to the Internet until later). Now, if I dig mymachine, I get 192.168.0.1, but if I try to nslookup mymachine, I get: >> connection timed out; no servers could be reached Tried also nslookup mymachine.mynicedomain.org - didn't work either. pinging (Edit:) succeeds. This happens both on the server machine itself and on other machines on the network. How can I the DNS lookups to work? What problem is preventing nslookup from succeeding? Additional Information In the server's /etc/hosts: 192.168.0.1 mymachine In the server's nsswitch.conf: hosts: files mdns4_mininal [NOTFOUND=return] dns mdns4 (admittedly, this is a bit weird; but I also tried: hosts: files dns instead, with the same effect) In resolv.conf (which is generated by dnsmasq): nameserver 127.0.0.1 search mynicedomain.org In the server's /etc/hosts.allow: domain: ALL In the other machines' /etc/resolv.conf (this is set by the DHCP client): nameserver 192.168.0.1 search mynicedomain.org Relevant netstat output on the server: Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 127.0.0.1:53 0.0.0.0:* LISTEN tcp 0 0 192.168.0.1:53 0.0.0.0:* LISTEN Finally, here's the ipconfig output from one of the client machines on the network (running Windows 7): Connection-specific DNS Suffix . : mynicedomain.org Description . . . . . . . . . . . : Intel(R) 82579LM Gigabit Network Connection Physical Address. . . . . . . . . : 12-34-56-78-9A-BC DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.0.50(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Sunday, October 20th 2013 16:20:25 Lease Expires . . . . . . . . . . : Sunday, October 20th 2013 18:20:24 Default Gateway . . . . . . . . . : 192.168.0.1 DHCP Server . . . . . . . . . . . : 192.168.0.1 DNS Servers . . . . . . . . . . . : 192.168.0.1 NetBIOS over Tcpip. . . . . . . . : Enabled Notes: May be related to this question.

  Read the article

• Windows XP periodically disconnects, reconnects; Windows 7 doesn't

  - by einpoklum

  My setup: I have a PC with a Gigabyte GA-MA78S2H motherboard (Realtek Gigabit wired Ethernet on-board). I have the latest drivers (at least the latest driver for the NIC. I'm connecting via an Edimax BR-6216Mg (again, wired connection). For some reason I experience short periodic disconnects and reconnects. Specifically, Skype disconnects, tries to connect, succeeds after a short while; incoming SFTP sessions get dropped; using a browser, I sometime get stuck in the DNS lookup or connection to the website and a page won't load. A couple of seconds later, a reload works. All this happens with Windows XP SP3. With Windows 7, it doesn't happen. The connection is smooth (OS is sluggish though, but never mind that). Like I said, I updated the NIC driver. I tried reducing the MTU (used something called Dr. TCP), thinking maybe that would help, but it didn't. (I'm a bit but not super-knowledgeable about TCP parameters.) I'm guessing it's either a problem with the driver or some settings which are different between the two OSes. ipconfig for my adapter: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 00-1D-7D-E9-72-9E Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.0.2 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.254 DHCP Server . . . . . . . . . . . : 192.168.0.254 DNS Servers . . . . . . . . . . . : 192.117.235.235 62.219.186.7 Lease Obtained. . . . . . . . . . : Saturday, March 10, 2012 8:28:20 AM Lease Expires . . . . . . . . . . : Friday, January 26, 1906 2:00:04 AM

  Read the article

• With dnsmasq as the DNS server, 'dig' succeeds, but 'nslookup' and 'ping' fail

  - by einpoklum

  I installed dnsmasq on a machine of mine (It's a Kubuntu 12.04 LTS), backed only by /etc/hosts (no connection to the Internet until later). Now, when I'm on the same machine as the dnsmasq - or any other machine on the server, I can dig mymachine and get 192.168.0.1, but if I try to nslookup mymachine, I get: >> connection timed out; no servers could be reached Tried also nslookup mymachine.mynicedomain.org - didn't work either. pinging fails. How can I the DNS lookups to work? Is the problem with the nsswitch entries? The dnsmasq configuration? Additional Information In the server's /etc/hosts: 192.168.0.1 mymachine In the server's nsswitch.conf: hosts: files mdns4_mininal [NOTFOUND=return] dns mdns4 (admittedly, this is a bit weird) In resolv.conf (which is generated by dnsmasq): nameserver 127.0.0.1 search mynicedomain.org In the server's /etc/hosts.allow: domain: ALL In the other machines' /etc/resolv.conf (this is set by the DHCP client): nameserver 192.168.0.1 search mynicedomain.org Finally, here's the ipconfig output from one of the client machines on the network (running Windows 7): Connection-specific DNS Suffix . : mynicedomain.org Description . . . . . . . . . . . : Intel(R) 82579LM Gigabit Network Connection Physical Address. . . . . . . . . : 12-34-56-78-9A-BC DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.0.50(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : Sunday, October 20th 2013 16:20:25 Lease Expires . . . . . . . . . . : Sunday, October 20th 2013 18:20:24 Default Gateway . . . . . . . . . : 192.168.0.1 DHCP Server . . . . . . . . . . . : 192.168.0.1 DNS Servers . . . . . . . . . . . : 192.168.0.1 NetBIOS over Tcpip. . . . . . . . : Enabled Notes: May be related to this question.

  Read the article

< Previous Page | 36 37 38 39 40 41 42  | Next Page >