Search Results

Search found 33406 results on 1337 pages for 'client library'.

Page 401/1337 | < Previous Page | 397 398 399 400 401 402 403 404 405 406 407 408  | Next Page >

  • Network speed between a VM and another machine which is not residing on the same host, is 11MB/s at most

    - by Henno
    Problem Network speed between a VM and another machine which is not residing on the same host, is 11MB/s at most. Topology Facts ESXi5 version is 5.0.0.504890 VM has the latest Vmware Tools installed VM is using E1000 network driver Physical box has Win Srv 2008 R2 as the OS CrystalDiskMark says the drive on physical box can read/write 100MB/s vCenter is another vm on esx both vm and physical box are showing 1Gbps link speed Configuration Networking shows vmnic0 as 1000 Full NTttcp is a client/server tool from Microsoft for measuring pure network throughput Here's what I've done so far: Test1: VM is running Filezilla FTP Server (default settings, one user account made) Physical box is running Filezilla FTP Client (default settings) Physical box is uploading a big file to FTP server Transfer speed (as observed by Windows Task Manager on both machines): ~11MB/s (bad) Physical box is downloading that file from FTP server Transfer speed (as observed by Windows Task Manager on both machines): still ~11MB/s (bad) Could it be disk performance issue? Test2: Physical box is running ntttcpr.exe -a 6 -m 6,0,VM_IP_ADDRESS VM is running ntttcps.exe -a 6 -m 6,0,PHY_BOX_IP_ADDRESS Transfer speed (as observed by Windows Task Manager on both machines): ~11MB/s (bad) Could it be switch performance issue? Test3: physical box is running vSphere Client I open Summary Storage datastore Browse Datastore... from physical box and upload a file to datastore Transfer speed (as observed by Windows Task Manager on physical box): ~26-36MB/s (good) Could it be a vm specific issue? Test4: Installed ntttcp to another vm on the same esx server Measured network performance between vms on the same esx server with NTttcp Transfer speed (as observed by Windows Task Manager on physical box): ~90-120MB/s (excellent :) Test5: I have another esx server on the same site, connecting to the same datastore and same switch. Those two ESX servers have both 2 NICs. One NIC goes to switch while the other goes directly to the other ESX server. vMotioned one of the testing vms off to the other ESX host Measured network performance between vms on different esx servers with NTttcp Transfer speed (as observed by Windows Task Manager on physical box): ~11MB/s (bad) While I'm aware of these: ESXi 4.1 slow file transfer ESXi 5 network performance is slow Debian Etch and ESXi slow network speeds VMWare ESXi slow file copy to guest they did not help (or I must have been missed something)

    Read the article

  • In an environment with multiple WiFi access points, do wireless clients sometimes connect to both at the same time?

    - by Bobby Burgess
    This is more of a curiosity than a problem, but in this new office I have two D-link DAP-2553's connected in a master/slave array (this just means the master keeps certain configuration options aligned with the slave). The network is set to 802.11n-only, and each AP has the same SSID and WPA2 key. The only difference is that they are on different channels (1 and 11). The WiFi network itself is working well. Users can roam around and the signal/speed is fairly consistent. However, I notice that when I look at the 802.11 client list in the web admin page for each of the 2 APs, I see that certain clients are connected to both, for extended periods of time, but I assume they are only passing data through one of them. Not every client is seen on each AP, but at any given time the same MAC address of a WiFi adapter can be associated (and remain associated) with both APs. The client list auto-refreshes every few seconds so I believe I'm looking at the most recent rather than stale information. One of the WiFi adapters that consistently associates with both APs is an Intel Centrino Wireless-N 1030 (laptop chip). Is it part of the WiFi standard that more than one association per WiFi card can be established concurrently on separate APS?

    Read the article

  • PHP displays blank white page even with all error reporting enabled

    - by Andy Shinn
    I am trying to debug a broken page in a Drupal application and am having a hard time getting PHP to spit anything useful out. I have the following set: error_reporting = E_ALL display_errors = On display_startup_errors = On log_errors = On error_log = /var/log/php/php_error.log I have a file showing me phpinfo() which confirms these variables are set correctly for the environment. I have increased memory_limit to 256M (which should be more than enough). Yet, the only indication I get is a status 500 code in the apache access log and a blank white page from PHP. The Apache virtual host has LogLevel set to debug and the error log only outputs: [Sat Jun 16 20:03:03 2012] [debug] mod_deflate.c(615): [client 173.8.175.217] Zlib: Compressed 0 to 2 : URL /index.php, referer: http://ec2-174-129-192-237.compute-1.amazonaws.com/admin/reports/updates [Sat Jun 16 20:03:03 2012] [error] [client 173.8.175.217] File does not exist: /var/www/favicon.ico [Sat Jun 16 20:03:03 2012] [debug] mod_deflate.c(615): [client 173.8.175.217] Zlib: Compressed 42 to 44 : URL /favicon.ico The PHP error log outputs nothing at all. kernel and syslog show nothing related to Apache or PHP. I have also tried installing suphp and checking its log just confirms the user is executing correctly: [Sat Jun 16 20:02:59 2012] [info] Executing "/var/www/index.php" as UID 1000, GID 1000 [Sat Jun 16 20:05:03 2012] [info] Executing "/var/www/index.php" as UID 1000, GID 1000 This is on Ubuntu 12.04 x86_64 with the following PHP modules: ii php5 5.3.10-1ubuntu3.1 server-side, HTML-embedded scripting language (metapackage) ii php5-cgi 5.3.10-1ubuntu3.1 server-side, HTML-embedded scripting language (CGI binary) ii php5-cli 5.3.10-1ubuntu3.1 command-line interpreter for the php5 scripting language ii php5-common 5.3.10-1ubuntu3.1 Common files for packages built from the php5 source ii php5-curl 5.3.10-1ubuntu3.1 CURL module for php5 ii php5-gd 5.3.10-1ubuntu3.1 GD module for php5 ii php5-mysql 5.3.10-1ubuntu3.1 MySQL module for php5 So, what am I missing here? Why no error reporting?

    Read the article

  • Why is Outlook 2007 resizing images in outgoing and incoming HTML email? How can I fix this?

    - by Mikuso
    In my Outlook 2007 client, embedded images in incoming emails appear resized when the message is viewed. The incoming images are resized to 198px wide, despite the original size. If it was larger, it will be shrunk; if it was smaller, it will be enlarged; the aspect ratio remains the same (the image is not stretched). This is local to my client only (i.e. another Outlook 2007 client reading the same IMAP inbox will see the image in the correct size. Similarly, viewing the email message in a browser will display the correct size). This happens regardless of whether width/height attributes are set on the image tag in the HTML. Zoom is set to 100% in my message window; text and other elements are not distorted from the original. In addition to this, outgoing HTML messages with images embedded in the same way are resized as they are sent. The outgoing images are all scaled to have a width of 247px. The source HTML of the outgoing message is changed after pressing Send so that the tag's width attribute is 247 pixels and the image file itself is also resized. These problems only occur with HTML messages; Rich Text messages do not have the same problem. I have already tried reinstalling Outlook and have it fully patched up to date. Why is this happening and how can I stop this?

    Read the article

  • Secure data from a server to a workstation using jumper hosts

    - by apalsson
    Hello. I have a WWW-server, my problem is that the content is sensitive and should not be accessible for people without proper credentials. How can I improve the ease of use but still maintain security following scenario; The Server is accessed through a "jumper host", i.e. the client connects to the jumper using VPN-connection and uses RemoteDesktop to access the jumper. From the jumper he uses RemoteDesktop again to access the Server. Finally on the Server the user can access content using a WWW-browser. All the way from the VPN-client to the WWW-browser requires authentication using a SmartCard-token. This seems quite secure to me. Content only gets mirrored on the RemoteDesktop between Server and jumper, no cached files to worry about. Connection between jumper and client is protected using VPN(ssl), so no eavesdropping. But it is quite cumbersome for the clients with many steps and connections to open. :( So, how can I improve the user experience accessing my server without compromising security? Thanks.

    Read the article

  • mount multiple folders with nfs4 on centos

    - by microchasm
    I'm trying to get nfs4 working here. Machine 1 (server) I have a folder and in it 2 other folders I'm trying to share independently. /shared/folder1 /shared/folder2 Problem is, I can't seem to figure out how to mount the folders independently on the client. (Machine 1 - server) /etc/exports: /var/shared/folder1 192.168.200.101(rw,fsid=0,sync) /var/shared/folder2 192.168.200.101(rw,fsid=0,sync) ... exportfs -ra (Machine 2 - client) /etc/fstab: 192.168.200.201:/folder1/ /home/nfsmnt/folder1 nfs4 rw 0 0 ... mount /home/nfsmnt/folder1 mount.nfs4: 192.168.200.201:/folder1/ failed, reason given by server: No such file or directory The folder is there. I'm positive. I think there is something simple I'm missing, but I'm totally missing it. It seems like there should be a way in fstab to tell nfs which folder on the server I want to mount. But I can only find references to what looks like a root mount point (e.g. 192.168.1.1:/) which I assume is handled by exports on the server. But even with the folders set up in exports, there doesn't seem to be an apparent way to pich and choose which gets mounted. Is it not possible to mount separate folders from the same server to different mount points on the client? Any help appreciated.

    Read the article

  • SVN hangs on commit - any suggestions for troubleshooting?

    - by Richard Beier
    We're having a problem with SVN... Subversion clients such as TortoiseSVN hang when we commit any more than a few files at a time to our server. Everything appears to actually be committed successfully to the repository; but the client hangs after all the data has been transmitted. We're using version 1.4.4 of the SVN server. We use the svn:// protocol rather than http to connect. We've reproduced this problem with several clients: TortoiseSVN (1.6.10), AnkhSVN (2.1), and the Silk command-line client (1.6.12). This is happening for everyone on the team, though some people seem to be more affected than others. If someone commits only a few files, it often works; but with more than half a dozen files, it usually hangs. Does anyone have troubleshooting suggestions? This has been happening sporadically for a while, but it's become pretty consistent lately. We've been working around the issue by killing the hung SVN client, doing "svn cleanup", and then doing "svn up"; but sometimes that causes tree conflicts. Another workaround is to blow away the workspace and check it out again after every commit; but of course that's pretty annoying. Are there any diagnostics that could help us troubleshoot this? We're considering upgrading to SVN 1.6 server, and installing the server on a new machine; but we're wondering if there's an easier solution. Thanks for your help, Richard

    Read the article

  • Connect by Wifi to Sql Server from another computer

    - by Bronzato
    I try to connect by Wifi to Sql Server with Sql Server Management Studio from another computer but it failed. I have a computer with Windows Seven & Sql Server 2008 (lets say the server computer). Next to it, I have a fresh installed computer with Windows Seven & Sql Server Management Studio (let's say the client computer). What I do on the server computer: configure firewall by enabling port 1433 enabled network protocols (TCP/IP) inside Sql Server Configuration Manager checked "Allow remote connections to this server" on server properties in Sql Server Management. started Sql Server Browser restarted services (Sql Server Browser is stopped but I think it is not neccessary, isn't it?) Next, I successfully tested a ping on the port 1433 from my client computer with a tool named tcping (ex: tcping 192.168.1.4 1433). But I still cannot connect from my client computer to Sql Server on my other computer. Ok, something new on this problem: until now, I successfully connected to my "server computer" with Management Studio. What I do is typing the computer name in the server name field in the connection window of Management Studio. My previous (failed) attempt was to type the computer name followed by the instance of sql server (ex: COMPUTER_NAME\SQL2008). I don't know why I only have to type the computer name... Nevermind. Now my new challenge is to succeed connecting my VB6 application to this remote database located on my "computer server". I have a connection string for this but it failed to connect. Here is my connection string: "Provider=SQLOLEDB.1;Password=mypassword;User ID=sa;Initial Catalog=TPB;Data Source=THIERRY-HP\SQL2008" Any idea what's wrong? Thanks

    Read the article

  • Samba Does Not List Files In Shared Directory

    - by Sean M
    I am running Samba on a CentOS server, and I am experiencing a problem where it allows me to connect to the server and see a share, but shows the share as an empty directory. I find this behavior strange. Here is the stanza in my smb.conf for the given share: [seanm] path = /home/seanm writeable = yes valid users = seanm, root read only = No Here's what I see on the server side: [seanm@server ~]$ ls -l -rw-r--r-- 1 seanm seanm 40 Jan 4 13:45 pangram.txt And yet: [seanm@client ~]$ smbclient //server/seanm -U seanm -W WORKGROUP Enter seanm's password: Domain=[WORKGROUP] OS=[Unix] Server=[Samba 3.0.33-3.29.el5_5.1] smb: \> ls . D 0 Fri Jan 7 10:08:55 2011 .. D 0 Fri Jan 7 07:58:31 2011 58994 blocks of size 262144. 50356 blocks available This behavior is present on both a Windows client and a Linux client system. The behavior is present with the firewall on and with the firewall off, so it's not that. Neither /var/log/messages nor /var/log/secure have any complaints about Samba. I doubt that SELinux is a problem: just in case, here are the relevant settings. [root@server ~]# getsebool -a | grep samba samba_domain_controller --> off samba_enable_home_dirs --> on samba_export_all_ro --> off samba_export_all_rw --> off samba_share_fusefs --> off samba_share_nfs --> off use_samba_home_dirs --> on virt_use_samba --> off What am I doing wrong here, and what can I do to fix it?

    Read the article

  • Group Policy for DNS Server Addresses

    - by John
    This question deals strictly with the methodology of using Active Directory to publish DNS settings and controlling the DNS server address order to domain attached clients. This is not asking about if this is the right function, role, or best use of group policy; but rather, how to make it work. I would like to be able to publish in group policy DNS addresses and possibly control the order in which the client consumes the addresses. I have tried following the information from this site without success. I set the following setting within group policy, but the client never shows the settings within the TCP/IP properties. Computer Configuration/Administrative Templates/Network/DNS Client/DNS Servers I did list them as a single space separated list. For example, the following: 192.168.0.1 192.168.10.3 192.168.34.2 192.168.2.67 192.168.56.99 192.168.99.23 This would be for Windows 7, Windows Server 2003, and Windows Server 2008 clients. I am not sure what I am doing wrong or how to get this to work. Am I missing a setting? Do I need to set something differently?

    Read the article

  • Excel or OpenOffice Table Summary: how to reconstruct a table from another, with "missing" values

    - by Gilberto
    I have a table of values (partial) with 3 columns: month (from 1 to 12), code and value. E.g., MONTH | CODE | VALUE 1 | aaa | 111 1 | bbb | 222 1 | ccc | 333 2 | aaa | 1111 2 | ccc | 2222 The codes are clients and the values are sales volumes. Each row represents the sales for one month for one client. So I have three clients, namely aaa, bbb, and ccc. For month=1 their sales volumes are: aaa-111, bbb-222, and ccc-333. A client may or may not have sales for every month; for example, for the month 2, the client bbb has no sales. I have to construct a completed summary table for all the MONTH / CODE pairs with their corresponding VALUE (using the value from the "partial" table, if present, otherwise print a string "missing"). MONTH | CODE | VALUE 1 | aaa | 111 1 | bbb | 222 1 | ccc | 333 2 | aaa | 1111 2 | bbb | missing 2 | ccc | 2222 Or, to put it another way, the table is a linear representation of a matrix:                                 and I want to identify the cells for which no value was provided. How can I do that?

    Read the article

  • RDP Connection to Windows 7 stays really slow

    - by Pavlo
    I have an Issue with connecting to Windows 7 via RDP. I can open an RDP Session, but regardless of any settings, the responce times are really long. This in particulary is the case when opening a web page in a browser. I've tried IE, Firefox and Google Chrome. I also use RDP connection to a Windows 2008 Server from the same client machine, and the speed is very normal with all features turned on. We have Gigabit Ethernet here. So I think it can not be the client's fault. What concerns Windows 7 Machine, I've tried shutting all the sraphic features off and turning the color levels to 256 colors. Result - the same. If I work locally on the machine - I can not see any lags. What else have I tried: Using old RDP 5 Client from Microsoft Setting network autotuninglevel as seen here Do You have some ideas? Thanks in advance! Update the problem seems to be with rendering window contents. All the window borders and pannes are rendered pretty quickly, but the content shows up very slowly. Also mouse movements are recognised by the Win 7 box only after some period. Are there some hidden settings in the RDP, where one could turn some advanced features off or turn some caching on? I use Bitmap Caching, but this apparently doesn't help.

    Read the article

  • LAMP Setup, PHP's session_start permission denied

    - by Andrew
    I'm trying to set up a development environment for a legacy system that runs CentOS 4.8, PHP 4.3.9, and MySQL 4.1.22. I'm matching OS and software versions to keep the development server as close to the production server as possible. When I fire up PHPMyAdmin's setup script (version 2.11.10.1, of course) the installation errors out and I see these errors in my error log: [client 172.18.141.74] PHP Warning: session_start(): open(/var/lib/php/session/sess_b5b90f86bd3dcfad315ff24cb7483a79, O_RDWR) failed: Permission denied (13) in /home/www/intranet/phpmyadmin/libraries/session.inc.php on line 87 [client 172.18.141.74] PHP Warning: Unknown(): open(/var/lib/php/session/sess_b5b90f86bd3dcfad315ff24cb7483a79, O_RDWR) failed: Permission denied (13) in Unknown on line 0 [client 172.18.141.74] PHP Warning: Unknown(): Failed to write session data (files). Please verify that the current setting of session.save_path is correct (/var/lib/php/session) in Unknown on line 0 I've done some searching on ServerFault and on teh Googles and I see that a common reason for this error is that the session.save_path isn't writable by the www user. I also found where in /etc/php.ini this URL is set: session.save_path. My session.save_path is set to: session.save_path = /var/lib/php/session I've since changed the owner and the group of /var/lib/php/session and still have the same error. Here's the result of ls -la for /var/lib/php [root@localhost php]# ls -la total 24 drwxrwxr-x 3 www www 4096 Oct 23 20:21 . drwxr-xr-x 17 root root 4096 Oct 23 20:31 .. drwxrwx--- 2 www www 4096 Jun 1 2009 session ...But I'm still getting the same error. Is there another possibility for why I'm getting this error?

    Read the article

  • How configure 2 Lan cards in Windows 7/8 pc one to connect to Internet and other to Local Network

    - by Maharshi Raval
        I am about to install a dedicated VOIP server in our office. It is a 3CX pbx system on Windows 7/8 machine. The environment currently is a Windows SBS 2011 with 8 client machines. I want to use a dedicated broadband connection for the PBX (3CX) box, but the box also needs to be accessible in the local network as we will be using IP Phones and software IP phones. How configure two network cards on PBX box, so that one will be always used to connect to our SIP host over the Internet and the other will be connected to local network accessible from other client pc to connect to the pbx system. It must be noted that currently the Windows SBS 2011 acts as the Primary Domain Controller and gateway for all the client machines.     I cannot use a load balancer as it will conflict and cause issues within the current setup of our SBS2011 as it is also our Exchange Server. Any input is much appreciated. thanks in advance

    Read the article

  • How configure 2 Lan cards in Windows 7/8 pc one to connect to Internet and other to Local Network

    - by Maharshi Raval
        I am about to install a dedicated VOIP server in our office. It is a 3CX pbx system on Windows 7/8 machine. The environment currently is a Windows SBS 2011 with 8 client machines. I want to use a dedicated broadband connection for the PBX (3CX) box, but the box also needs to be accessible in the local network as we will be using IP Phones and software IP phones. How configure two network cards on PBX box, so that one will be always used to connect to our SIP host over the Internet and the other will be connected to local network accessible from other client pc to connect to the pbx system. It must be noted that currently the Windows SBS 2011 acts as the Primary Domain Controller and gateway for all the client machines.     I cannot use a load balancer as it will conflict and cause issues within the current setup of our SBS2011 as it is also our Exchange Server. Any input is much appreciated. thanks in advance

    Read the article

  • IIS not responding with SSL Server Hello

    - by Damien_The_Unbeliever
    I'm having difficulty getting a particular IIS machine to "do" SSL. This is a test environment (one of many) which we've set up "the same" as we have many times previously, but it just doesn't seem to be working. The server is Windows Server 2003 (Version 5.2 (Build 3790.srv03_sp2_gdr.100216-1301 : Service Pack 2)) IIS is hosting 4 sites (including the default site), but only one site is configured for SSL. We're using the same SSL certificate we use on all of our other servers (it's a wildcard cert). (Don't think this is relevant, but including anyway) We've configured the site to require SSL, it has a subdirectory that doesn't require SSL but has an asp page that redirects into SSL. The 403;4 error page for the site is hooked up to this asp page (this is how we do our non-HTTPS into HTTPS transition). Using Microsoft Network Monitor (3.3), I've just run a session against a server where SSL is working. It can pull apart the SSL exchange as the following messages: SSL: Client Hello SSL: Server Hello. Certificate. Server Hello Done SSL: Client Key Exchange. Change Cipher Spec. Encrypted Handshake Message. SSL: Change Cipher Spec. Encrypted Handshake Message However, on our problem server, I only see: SSL: Client Hello. The next packet from the server (from port 443, so it's listening and responding there) contains only 60 bytes, and just seems to have the Tcp headers and not much else (but I'm by no means an expert at deciphering these things). So, where do I look next? Or what additional information do I need to add to this question, and where do I find it?

    Read the article

  • How to import a text file into powershell and email it, formatted as HTML

    - by Don
    I'm trying to get a list of all Exchange accounts, format them in descending order from largest mailbox and put that data into an email in HTML format to email to myself. So far I can get the data, push it to a text file as well as create an email and send to myself. I just can't seem to get it all put together. I've been trying to use ConvertTo-Html but it just seems to return data via email like "pageFooterEntry" and "Microsoft.PowerShell.Commands.Internal.Format.AutosizeInfo" versus the actual data. I can get it to send me the right data if i don't tell it to ConvertTo-Html, just have it pipe the data to a text file and pull from it, but it's all ran together with no formatting. I don't need to save the file, i'd just like to run the command, get the data, put it in HTML and mail it to myself. Here's what I have currently: #Connects to Database and returns information on all users, organized by Total Item Size, User $body = Get-MailboxStatistics -database "Mailbox Database 0846468905" | where {$_.ObjectClass -eq “Mailbox”} | Sort-Object TotalItemSize -Descending | ft @{label=”User”;expression={$_.DisplayName}},@{label=”Total Size (MB)”;expression={$_.TotalItemSize.Value.ToMB()}} -auto | ConvertTo-Html #Pause for 5 seconds for Exchange write-host -foregroundcolor Green "Pausing for 5 seconds for Exchange" Start-Sleep -s 5 $toemail = "[email protected]" # Emails report to this address. $fromemail = "[email protected]" #Emails from this address. $server = "Exchange.company.com" #Exchange server - SMTP. #Email the report. $email = New-Object System.Net.Mail.MailMessage $email.IsBodyHtml = $True $email.To.Add($toemail) $email.From = $fromemail $email.Subject = "Exchange Mailbox Sizes" $email.Body = $body $client = New-Object System.Net.Mail.SmtpClient $server $client.UseDefaultCredentials = $true $client.Send($email) Any thoughts would be helpful, thanks!

    Read the article

  • How can I setup a Proxy I can sniff traffic from using an ESX vswitch in promiscuous mode?

    - by sandroid
    I have a pretty specific requirement, detailed below. Here's what I'm not looking for help for, to keep things tidy and on topic: How to configure a standard proxy Any ESX setup required to facilitate traffic sniffing How to sniff traffic Any changes in design (my scope limits me) I need to setup a test environment for a network-sniffing based HTTP app monitoring tool, and I need to troubleshoot a client issue but he only has a prod network, so making changes to the config on client's system "just to try" is costly. The goal here is to create a similar system in my lab, and hit the client's webapp and redirect my traffic - using a proxy - into the lab environment. The reason I want to use a proxy is so that only this specific traffic is redirected for all to see, and not all my web traffic (like my visits to serverfault :P). Everything will run inside an ESX 4.1 machine. In there, there is a traffic collection vswitch in promiscuous mode that is not on the local network for security reasons. The VM containing our listening agent is connected to this vswitch. On the same ESX host, I will setup a basic linux server and install a proxy (either apache + mod_proxy or squid, doesn't matter). I'm looking for ideas on how to deploy this for my needs so I can then figure out how to set it up accordingly. Some ideas I've had were to setup two proxies, and have them talk to eachother through this vswitch in promiscuous mode, but it seems like alot of work. Another idea is a dual-homed proxy, but I've never seen/done that before so I'm not sure how doable it is for what I'd like. I am OK with setting up a second vswitch in promiscuous mode to facilitate this if need be, but I cannot put the vswitch on the lan (which is used so my browser would communicate with the proxy) in promiscuous mode. Any ideas are welcome.

    Read the article

  • iTunes copy just metadata (song and album ratings, playlists) from iPod

    - by Jared Updike
    I have an iPod touch that I synched with my Windows computer (iTunes 9.0 I think) until my harddrive failed and I lost my entire library. I rebuilt the library (songs) from a year old backup (and various other source for songs) but my playlists and ratings are of course a year old. My iPod itself has most of the playlists and ratings I care most about (favorite songs and albums, rated 4 and 5, for example). I have a catch 22 situation where I feel nervous that I haven't backed up my iPod in around 4 months (when my drive failed) so I'd like to back it up as soon as possible... but if I back it up I have to clear all the songs and playlists and copy them back, which I can't really do since I need to rebuild my playlists on my computer first (using the data only available on my iPod!) The question: is there a better way to READ the information off my iPod than doing it manually, song by song and album by album and playlist by playlist (XML, text dump, database, spreadsheet, anything). In other words, mostly I want the information (metadata like ratings and playlists, not songs) copied off the iPod so I can more quickly get my iTunes library ratings and playlists re-built (manually) so I can finally wipe the music and back up my apps, etc. Then I'd like to copy the music back immediately. The part I'd like to avoid is manually navigating everything on my iPod to read through all the playlists and ratings (50 GB, 6,000+ songs) as I re-enter all of that data by hand. I've done a few dozen albums and it's pretty time consuming having to tap around on the iPod. Reading from a spreadsheet (for example, or XML which I could write a script to get into spreadsheet form) would probably help tremendously, plus then I'd have a backup of that information somewhere besides just my iPod.

    Read the article

  • Mac updated just now, postgres now broken

    - by user52224
    I run postgres 9.1 / ruby 1.9.2 / rails 3.1.0 on a maxbook air for local dev. It's all been running smoothly for months, (though this is the first time I've done development on a mac.) It's a macbook air from last year, and today I got the mac osx software update message as I have a few times before, and my system downloaded approx 450mb of updates and restarted. It now says it's on OSX 10.7.3. Point is, postgres has stopped working, when I start my thin server (mirror heroku cedar) as normal, and then browse to my rails app I get: PG::Error could not connect to server: Permission denied Is the server running locally and accepting connections on Unix domain socket "/var/pgsql_socket/.s.PGSQL.5432"? What happened? After browsing around a few questions I'm still confused, but here's some extra info: Running psql from command line gives same error I can run pgadmin 3 and connect via it and run SQL no problems Running which psql shows the version as /usr/bin/psql I created a PostgreSQL user back when I got the mac (it's always been on lion) I've no idea why, almost certainly I was following a tutorial which I neglected to store in my notes. Point is I am aware there is a _postgres user as well. I know it's rubbish, but apart from a note on passwords, I don't have any extra info on how I configured postgres - though the obvious implication is that I did not use the _postgres user. Anyone have suggestions or information on what might have changed / what I can try to debug and fix? Thanks. Edit: Playing around based on this question and answer: http://stackoverflow.com/questions/7975414/check-status-of-postgresql-server-mac-os-x, see this string of commands: $ sudo su postgreSQL bash-3.2$ /Library/PostgreSQL/9.1/bin/pg_ctl start -D /Library/PostgreSQL/9.1/data pg_ctl: another server might be running; trying to start server anyway server starting bash-3.2$ 2012-04-08 19:03:39 GMT FATAL: lock file "postmaster.pid" already exists 2012-04-08 19:03:39 GMT HINT: Is another postmaster (PID 68) running in data directory "/Library/PostgreSQL/9.1/data"? bash-3.2$ exit

    Read the article

  • MAMP Pro mysqld won't start on os x lion

    - by Mike
    getting a Start MySQL Failed error in the GUI.. when i attempt to start mysqld from the CLI i get the following error: ? /Applications/MAMP/Library/bin/mysqld 120623 23:12:47 [Warning] Setting lower_case_table_names=2 because file system for /Applications/MAMP/db/mysql/ is case insensitive 120623 23:12:47 [Note] Plugin 'FEDERATED' is disabled. 120623 23:12:47 InnoDB: The InnoDB memory heap is disabled 120623 23:12:47 InnoDB: Mutexes and rw_locks use GCC atomic builtins 120623 23:12:47 InnoDB: Compressed tables use zlib 1.2.3 120623 23:12:47 InnoDB: Initializing buffer pool, size = 128.0M 120623 23:12:47 InnoDB: Completed initialization of buffer pool 120623 23:12:47 InnoDB: highest supported file format is Barracuda. 120623 23:12:47 InnoDB: Waiting for the background threads to start 120623 23:12:48 InnoDB: 1.1.5 started; log sequence number 1595675 120623 23:12:48 [ERROR] /Applications/MAMP/Library/bin/mysqld: unknown option '--skip-locking' 120623 23:12:48 [ERROR] Aborting 120623 23:12:48 InnoDB: Starting shutdown... 120623 23:12:49 InnoDB: Shutdown completed; log sequence number 1595675 120623 23:12:49 [Note] /Applications/MAMP/Library/bin/mysqld: Shutdown complete i have deleted the mysql.pid file located at /application/mamp/tmp/mysql/mysql.pid and i still get the error above. I can't find where MAMP has set --skip-locking set, my.cnf doesnt have it anywhere. Activity monitor gives me a mysqld process running by me, and everytime i KILL the process both via Activity Monitor and via kill =9 pid it starts right back up.. Sampling the process points back to the MAMP mysqld.. wtf?! About to throw MAMP out the window and boot up a VM of CentOS =)

    Read the article

  • DHCP Relay setup in ubuntu server

    - by jerichorivera
    I have a network appliance (QNO) that works as traffic load balancer and dhcp server. I would like to add a linux server in between the network appliance and the client computers. The linux server will be used to monitor bandwidth usage. My problem is I still want DHCP to be served by the network appliance so that load balancing will still work efficiently. We are afraid that if we setup the linux server as the DHCP server the network appliance will not be able to load balance the traffic if it only sees the linux server as a single client connecting to it. I've been searching all over for a tutorial on how to setup DHCP relay but have not found any. How do I setup DHCP relay on my linux server given there are two NICs attached to it, one connects the linux server to the network appliance and the other connects the linux server to the client computers. EDIT Router (DHCP) ---- [eth0] Linux Server (Relay agent) [eth1] ----- PC (network) Router IP is 192.168.0.100 eth0 is on DHCP eth1 is static 192.168.2.11 (if I need to change this I can) Tried to do dhcrelay -i eth1 192.168.0.100, but the PC was not getting any DHCP lease from the DHCP router. I might be missing something here.

    Read the article

  • why won't php 5.3.3 compile libphp5.so on redhat ent

    - by spatel
    I'm trying to upgrade to php 5.3.3 from php 5.2.13. However, the apache module, libphp5.so will not be compiled. Below is a output I got along with the configure options I used. The configure statement is a reduced version of what I normally use. ========== './configure' '--disable-debug' '--disable-rpath' '--with-apxs2=/usr/local/apache2/bin/apxs' ... ** ** ** Warning: inter-library dependencies are not known to be supported. ** ** ** All declared inter-library dependencies are being dropped. ** ** ** Warning: libtool could not satisfy all declared inter-library ** ** ** dependencies of module libphp5. Therefore, libtool will create ** ** ** a static module, that should work as long as the dlopening ** ** ** application is linked with the -dlopen flag. copying selected object files to avoid basename conflicts... Generating phar.php Generating phar.phar PEAR package PHP_Archive not installed: generated phar will require PHP's phar extension be enabled. clicommand.inc pharcommand.inc directorytreeiterator.inc directorygraphiterator.inc invertedregexiterator.inc phar.inc Build complete. Don't forget to run 'make test'. ============= php 5.2.13 recompiles just fine so something is up with 5.3.3. Any help would be greatly appreciated!!

    Read the article

  • iTunes copy just metadata (song and album ratings, playlists) from iPod

    - by Jared Updike
    I have an iPod touch that I synched with my Windows computer (iTunes 9.0 I think) until my harddrive failed and I lost my entire library. I rebuilt the library (songs) from a year old backup (and various other source for songs) but my playlists and ratings are of course a year old. My iPod itself has most of the playlists and ratings I care most about (favorite songs and albums, rated 4 and 5, for example). I have a catch 22 situation where I feel nervous that I haven't backed up my iPod in around 4 months (when my drive failed) so I'd like to back it up as soon as possible... but if I back it up I have to clear all the songs and playlists and copy them back, which I can't really do since I need to rebuild my playlists on my computer first (using the data only available on my iPod!) The question: is there a better way to READ the information off my iPod than doing it manually, song by song and album by album and playlist by playlist (XML, text dump, database, spreadsheet, anything). In other words, mostly I want the information (metadata like ratings and playlists, not songs) copied off the iPod so I can more quickly get my iTunes library ratings and playlists re-built (manually) so I can finally wipe the music and back up my apps, etc. Then I'd like to copy the music back immediately. The part I'd like to avoid is manually navigating everything on my iPod to read through all the playlists and ratings (50 GB, 6,000+ songs) as I re-enter all of that data by hand. I've done a few dozen albums and it's pretty time consuming having to tap around on the iPod. Reading from a spreadsheet (for example, or XML which I could write a script to get into spreadsheet form) would probably help tremendously, plus then I'd have a backup of that information somewhere besides just my iPod.

    Read the article

  • How to setup a hyper-v domain with internet access

    - by fynnbob
    First off let me say that I'm not a network admin or server guy, I know very little about that stuff. What I'm trying to do is setup a virtualized domain using hyper-V. Here is the configuration: Physical Server: 4Mb RAM Windows Server 2008 R2 running Hyper-V Virtual Environment: One Domain Controller running Windows Server 2008 R2 One Client running Windows Server 2008 R2 I have been successful in setting up a virtual domain controller and adding a virtual client to that domain controller but I'm stuck at trying to give the virtual Environment Internet access. I can give the client VM Internet access if I remove them from the virtual domain but once I add them back to the virtual domain, Internet access is gone. I've read articles describing many different ways this can be done (using RRAS with NAT, using a wireless connection, etc...) but all of those articles only cover a small piece of the setup and also seem to be geared towards people who know there way around networking and servers which I don't. I'd like to know more but my thing is software development and I have my hands full trying to keep up with everything in that realm. I simply want to setup a virtual domain with Internet access for testing. Can anyone point me to any "for Dummy's" type information on how to setup this type of environment or can anyone provide this kind of step-by-step help. Any help would be very much appreciated.

    Read the article

< Previous Page | 397 398 399 400 401 402 403 404 405 406 407 408  | Next Page >