Search Results

Search found 18897 results on 756 pages for 'network connectivity'.

Page 401/756 | < Previous Page | 397 398 399 400 401 402 403 404 405 406 407 408  | Next Page >

• Receiving Multicast Messages on a Multihomed Windows PC

  - by Basti

  I'm developing a diagnostic tool on a PC with several Network Interfaces based on multicast/udp. The user can select a NIC, the application creates sockets, binds them to this NIC and adds them to the specific multicast group. The sending of multicast messages works fine. However receiving of messages only succeeds if I bind the sockets to a specific NIC of my PC. It almost looks like as there is a 'default' NIC for receiving multicast messages in Windows which is always the first NIC returned by the GetAdapterInfo function. I monitored the network with Wireshark and discovered that the "IGMP Join Group" message isn't sent from the NIC I bound the socket at, but by this 'default' NIC. If I disable this NIC (or remove the network cable), the next NIC of the list returned by GetAdapterInfo is used for receiving multicast messages. I was successful to change this 'default' NIC by adding an additional entry to the routing table of my PC, but I don't think this is a good solution of the problem. The problem also occurs with the code appended below. The join group messages isn't sent via 192.168.52 but via a different NIC. // socket_tst.cpp : Defines the entry point for the console application. // #include tchar.h #include winsock2.h #include ws2ipdef.h #include IpHlpApi.h #include IpTypes.h #include stdio.h int _tmain(int argc, _TCHAR* argv[]) { WSADATA m_wsaData; SOCKET m_socket; sockaddr_in m_sockAdr; UINT16 m_port = 319; u_long m_interfaceAdr = inet_addr("192.168.1.52"); u_long m_multicastAdr = inet_addr("224.0.0.107"); int returnValue = WSAStartup(MAKEWORD(2,2), &m_wsaData); if (returnValue != S_OK) { return returnValue; } // Create sockets if (INVALID_SOCKET == (m_socket = socket(AF_INET, SOCK_DGRAM, IPPROTO_UDP)) ) { return WSAGetLastError(); } int doreuseaddress = TRUE; if (setsockopt(m_socket,SOL_SOCKET,SO_REUSEADDR,(char*) &doreuseaddress,sizeof(doreuseaddress)) == SOCKET_ERROR) { return WSAGetLastError(); } // Configure socket addresses memset(&m_sockAdr,0,sizeof(m_sockAdr)); m_sockAdr.sin_family = AF_INET; m_sockAdr.sin_port = htons(m_port); m_sockAdr.sin_addr.s_addr = m_interfaceAdr; //bind sockets if ( bind( m_socket, (SOCKADDR*) &m_sockAdr, sizeof(m_sockAdr) ) == SOCKET_ERROR ) { return WSAGetLastError(); } // join multicast struct ip_mreq_source imr; memset(&imr,0,sizeof(imr)); imr.imr_multiaddr.s_addr = m_multicastAdr; // address of multicastgroup imr.imr_sourceaddr.s_addr = 0; // sourceaddress (not used) imr.imr_interface.s_addr = m_interfaceAdr; // interface address /* first join multicast group, then registerer selected interface as * multicast sending interface */ if( setsockopt( m_socket ,IPPROTO_IP ,IP_ADD_MEMBERSHIP ,(char*) &imr , sizeof(imr)) == SOCKET_ERROR) { return SOCKET_ERROR; } else { if( setsockopt(m_socket ,IPPROTO_IP ,IP_MULTICAST_IF ,(CHAR*)&imr.imr_interface.s_addr ,sizeof(&imr.imr_interface.s_addr)) == SOCKET_ERROR ) { return SOCKET_ERROR; } } printf("receiving msgs...\n"); while(1) { // get inputbuffer from socket int sock_return = SOCKET_ERROR; sockaddr_in socketAddress; char buffer[1500]; int addressLength = sizeof(socketAddress); sock_return = recvfrom(m_socket, (char*) &buffer, 1500, 0, (SOCKADDR*)&socketAddress, &addressLength ); if( sock_return == SOCKET_ERROR) { int wsa_error = WSAGetLastError(); return wsa_error; } else { printf("got message!\n"); } } return 0; } Thanks four your help!

  Read the article

• FreeBSD performance tuning. Sysctls, loader.conf, kernel

  - by SaveTheRbtz

  I wanted to share knowledge of tuning FreeBSD via sysctl.conf/loader.conf/KENCONF. It was initially based on Igor Sysoev's (author of nginx) presentation about FreeBSD tuning up to 100,000-200,000 active connections. Tunings are for FreeBSD-CURRENT. Since 7.2 amd64 some of them are tuned well by default. Prior 7.0 some of them are boot only (set via /boot/loader.conf) or does not exist at all. sysctl.conf: # No zero mapping feature # May break wine # (There are also reports about broken samba3) #security.bsd.map_at_zero=0 # If you have really busy webserver with apache13 you may run out of processes #kern.maxproc=10000 # Same for servers with apache2 / Pound #kern.threads.max_threads_per_proc=4096 # Max. backlog size kern.ipc.somaxconn=4096 # Shared memory // 7.2+ can use shared memory > 2Gb kern.ipc.shmmax=2147483648 # Sockets kern.ipc.maxsockets=204800 # Can cause this on older kernels: # http://old.nabble.com/Significant-performance-regression-for-increased-maxsockbuf-on-8.0-RELEASE-tt26745981.html#a26745981 ) kern.ipc.maxsockbuf=10485760 # Mbuf 2k clusters (on amd64 7.2+ 25600 is default) # For such high value vm.kmem_size must be increased to 3G kern.ipc.nmbclusters=262144 # Jumbo pagesize(_SC_PAGESIZE) clusters # Used as general packet storage for jumbo frames # can be monitored via `netstat -m` #kern.ipc.nmbjumbop=262144 # Jumbo 9k/16k clusters # If you are using them #kern.ipc.nmbjumbo9=65536 #kern.ipc.nmbjumbo16=32768 # For lower latency you can decrease scheduler's maximum time slice # default: stathz/10 (~ 13) #kern.sched.slice=1 # Increase max command-line length showed in `ps` (e.g for Tomcat/Java) # Default is PAGE_SIZE / 16 or 256 on x86 # This avoids commands to be presented as [executable] in `ps` # For more info see: http://www.freebsd.org/cgi/query-pr.cgi?pr=120749 kern.ps_arg_cache_limit=4096 # Every socket is a file, so increase them kern.maxfiles=204800 kern.maxfilesperproc=200000 kern.maxvnodes=200000 # On some systems HPET is almost 2 times faster than default ACPI-fast # Useful on systems with lots of clock_gettime / gettimeofday calls # See http://old.nabble.com/ACPI-fast-default-timecounter,-but-HPET-83--faster-td23248172.html # After revision 222222 HPET became default: http://svnweb.freebsd.org/base?view=revision&revision=222222 kern.timecounter.hardware=HPET # Small receive space, only usable on http-server, on file server this # should be increased to 65535 or even more #net.inet.tcp.recvspace=8192 # This is useful on Fat-Long-Pipes #net.inet.tcp.recvbuf_max=10485760 #net.inet.tcp.recvbuf_inc=65535 # Small send space is useful for http servers that serve small files # Autotuned since 7.x net.inet.tcp.sendspace=16384 # This is useful on Fat-Long-Pipes #net.inet.tcp.sendbuf_max=10485760 #net.inet.tcp.sendbuf_inc=65535 # Turn off receive autotuning # You can play with it. #net.inet.tcp.recvbuf_auto=0 #net.inet.tcp.sendbuf_auto=0 # This should be enabled if you going to use big spaces (>64k) # Also timestamp field is useful when using syncookies net.inet.tcp.rfc1323=1 # Turn this off on high-speed, lossless connections (LAN 1Gbit+) # If you set it there is no need in TCP_NODELAY sockopt (see man tcp) net.inet.tcp.delayed_ack=0 # This feature is useful if you are serving data over modems, Gigabit Ethernet, # or even high speed WAN links (or any other link with a high bandwidth delay product), # especially if you are also using window scaling or have configured a large send window. # Automatically disables on small RTT ( http://www.freebsd.org/cgi/cvsweb.cgi/src/sys/netinet/tcp_subr.c?#rev1.237 ) # This sysctl was removed in 10-CURRENT: # See: http://www.mail-archive.com/[email protected]/msg06178.html #net.inet.tcp.inflight.enable=0 # TCP slowstart algorithm tunings # We assuming we have very fast clients #net.inet.tcp.slowstart_flightsize=100 #net.inet.tcp.local_slowstart_flightsize=100 # Disable randomizing of ports to avoid false RST # Before usage check SA here www.bsdcan.org/2006/papers/ImprovingTCPIP.pdf # (it's also says that port randomization auto-disables at some conn.rates, but I didn't checked it thou) #net.inet.ip.portrange.randomized=0 # Increase portrange # For outgoing connections only. Good for seed-boxes and ftp servers. net.inet.ip.portrange.first=1024 net.inet.ip.portrange.last=65535 # # stops route cache degregation during a high-bandwidth flood # http://www.freebsd.org/doc/en/books/handbook/securing-freebsd.html #net.inet.ip.rtexpire=2 net.inet.ip.rtminexpire=2 net.inet.ip.rtmaxcache=1024 # Security net.inet.ip.redirect=0 net.inet.ip.sourceroute=0 net.inet.ip.accept_sourceroute=0 net.inet.icmp.maskrepl=0 net.inet.icmp.log_redirect=0 net.inet.icmp.drop_redirect=1 net.inet.tcp.drop_synfin=1 # # There is also good example of sysctl.conf with comments: # http://www.thern.org/projects/sysctl.conf # # icmp may NOT rst, helpful for those pesky spoofed # icmp/udp floods that end up taking up your outgoing # bandwidth/ifqueue due to all that outgoing RST traffic. # #net.inet.tcp.icmp_may_rst=0 # Security net.inet.udp.blackhole=1 net.inet.tcp.blackhole=2 # IPv6 Security # For more info see http://www.fosslc.org/drupal/content/security-implications-ipv6 # Disable Node info replies # To see this vulnerability in action run `ping6 -a sglAac ::1` or `ping6 -w ::1` on unprotected node net.inet6.icmp6.nodeinfo=0 # Turn on IPv6 privacy extensions # For more info see proposal http://unix.derkeiler.com/Mailing-Lists/FreeBSD/net/2008-06/msg00103.html net.inet6.ip6.use_tempaddr=1 net.inet6.ip6.prefer_tempaddr=1 # Disable ICMP redirect net.inet6.icmp6.rediraccept=0 # Disable acceptation of RA and auto linklocal generation if you don't use them #net.inet6.ip6.accept_rtadv=0 #net.inet6.ip6.auto_linklocal=0 # Increases default TTL, sometimes useful # Default is 64 net.inet.ip.ttl=128 # Lessen max segment life to conserve resources # ACK waiting time in miliseconds # (default: 30000. RFC from 1979 recommends 120000) net.inet.tcp.msl=5000 # Max bumber of timewait sockets net.inet.tcp.maxtcptw=200000 # Don't use tw on local connections # As of 15 Apr 2009. Igor Sysoev says that nolocaltimewait has some buggy realization. # So disable it or now till get fixed #net.inet.tcp.nolocaltimewait=1 # FIN_WAIT_2 state fast recycle net.inet.tcp.fast_finwait2_recycle=1 # Time before tcp keepalive probe is sent # default is 2 hours (7200000) #net.inet.tcp.keepidle=60000 # Should be increased until net.inet.ip.intr_queue_drops is zero net.inet.ip.intr_queue_maxlen=4096 # Interrupt handling via multiple CPU, but with context switch. # You can play with it. Default is 1; #net.isr.direct=0 # This is for routers only #net.inet.ip.forwarding=1 #net.inet.ip.fastforwarding=1 # This speed ups dummynet when channel isn't saturated net.inet.ip.dummynet.io_fast=1 # Increase dummynet(4) hash #net.inet.ip.dummynet.hash_size=2048 #net.inet.ip.dummynet.max_chain_len # Should be increased when you have A LOT of files on server # (Increase until vfs.ufs.dirhash_mem becomes lower) vfs.ufs.dirhash_maxmem=67108864 # Note from commit http://svn.freebsd.org/base/head@211031 : # For systems with RAID volumes and/or virtualization envirnments, where # read performance is very important, increasing this sysctl tunable to 32 # or even more will demonstratively yield additional performance benefits. vfs.read_max=32 # Explicit Congestion Notification (see http://en.wikipedia.org/wiki/Explicit_Congestion_Notification) net.inet.tcp.ecn.enable=1 # Flowtable - flow caching mechanism # Useful for routers #net.inet.flowtable.enable=1 #net.inet.flowtable.nmbflows=65535 # Extreme polling tuning #kern.polling.burst_max=1000 #kern.polling.each_burst=1000 #kern.polling.reg_frac=100 #kern.polling.user_frac=1 #kern.polling.idle_poll=0 # IPFW dynamic rules and timeouts tuning # Increase dyn_buckets till net.inet.ip.fw.curr_dyn_buckets is lower net.inet.ip.fw.dyn_buckets=65536 net.inet.ip.fw.dyn_max=65536 net.inet.ip.fw.dyn_ack_lifetime=120 net.inet.ip.fw.dyn_syn_lifetime=10 net.inet.ip.fw.dyn_fin_lifetime=2 net.inet.ip.fw.dyn_short_lifetime=10 # Make packets pass firewall only once when using dummynet # i.e. packets going thru pipe are passing out from firewall with accept #net.inet.ip.fw.one_pass=1 # shm_use_phys Wires all shared pages, making them unswappable # Use this to lessen Virtual Memory Manager's work when using Shared Mem. # Useful for databases #kern.ipc.shm_use_phys=1 # ZFS # Enable prefetch. Useful for sequential load type i.e fileserver. # FreeBSD sets vfs.zfs.prefetch_disable to 1 on any i386 systems and # on any amd64 systems with less than 4GB of avaiable memory # For additional info check this nabble thread http://old.nabble.com/Samba-read-speed-performance-tuning-td27964534.html #vfs.zfs.prefetch_disable=0 # On highload servers you may notice following message in dmesg: # "Approaching the limit on PV entries, consider increasing either the # vm.pmap.shpgperproc or the vm.pmap.pv_entry_max tunable" vm.pmap.shpgperproc=2048 loader.conf: # Accept filters for data, http and DNS requests # Useful when your software uses select() instead of kevent/kqueue or when you under DDoS # DNS accf available on 8.0+ accf_data_load="YES" accf_http_load="YES" accf_dns_load="YES" # Async IO system calls aio_load="YES" # Linux specific devices in /dev # As for 8.1 it only /dev/full #lindev_load="YES" # Adds NCQ support in FreeBSD # WARNING! all ad[0-9]+ devices will be renamed to ada[0-9]+ # 8.0+ only #ahci_load="YES" #siis_load="YES" # FreeBSD 8.2+ # New Congestion Control for FreeBSD # http://caia.swin.edu.au/urp/newtcp/tools/cc_chd-readme-0.1.txt # http://www.ietf.org/proceedings/78/slides/iccrg-5.pdf # Initial merge commit message http://www.mail-archive.com/[email protected]/msg31410.html #cc_chd_load="YES" # Increase kernel memory size to 3G. # # Use ONLY if you have KVA_PAGES in kernel configuration, and you have more than 3G RAM # Otherwise panic will happen on next reboot! # # It's required for high buffer sizes: kern.ipc.nmbjumbop, kern.ipc.nmbclusters, etc # Useful on highload stateful firewalls, proxies or ZFS fileservers # (FreeBSD 7.2+ amd64 users: Check that current value is lower!) #vm.kmem_size="3G" # If your server has lots of swap (>4Gb) you should increase following value # according to http://lists.freebsd.org/pipermail/freebsd-hackers/2009-October/029616.html # Otherwise you'll be getting errors # "kernel: swap zone exhausted, increase kern.maxswzone" # kern.maxswzone="256M" # Older versions of FreeBSD can't tune maxfiles on the fly #kern.maxfiles="200000" # Useful for databases # Sets maximum data size to 1G # (FreeBSD 7.2+ amd64 users: Check that current value is lower!) #kern.maxdsiz="1G" # Maximum buffer size(vfs.maxbufspace) # You can check current one via vfs.bufspace # Should be lowered/upped depending on server's load-type # Usually decreased to preserve kmem # (default is 10% of mem) #kern.maxbcache="512M" # Sendfile buffers # For i386 only #kern.ipc.nsfbufs=10240 # FreeBSD 9+ # HPET "legacy route" support. It should allow HPET to work per-CPU # See http://www.mail-archive.com/[email protected]/msg03603.html #hint.atrtc.0.clock=0 #hint.attimer.0.clock=0 #hint.hpet.0.legacy_route=1 # syncache Hash table tuning net.inet.tcp.syncache.hashsize=1024 net.inet.tcp.syncache.bucketlimit=512 net.inet.tcp.syncache.cachelimit=65536 # Increased hostcache # Later host cache can be viewed via net.inet.tcp.hostcache.list hidden sysctl # Very useful for it's RTT RTTVAR # Must be power of two net.inet.tcp.hostcache.hashsize=65536 # hashsize * bucketlimit (which is 30 by default) # It allocates 255Mb (1966080*136) of RAM net.inet.tcp.hostcache.cachelimit=1966080 # TCP control-block Hash table tuning net.inet.tcp.tcbhashsize=4096 # Disable ipfw deny all # Should be uncommented when there is a chance that # kernel and ipfw binary may be out-of sync on next reboot #net.inet.ip.fw.default_to_accept=1 # # SIFTR (Statistical Information For TCP Research) is a kernel module that # logs a range of statistics on active TCP connections to a log file. # See prerelease notes http://groups.google.com/group/mailing.freebsd.current/browse_thread/thread/b4c18be6cdce76e4 # and man 4 sitfr #siftr_load="YES" # Enable superpages, for 7.2+ only # Also read http://lists.freebsd.org/pipermail/freebsd-hackers/2009-November/030094.html vm.pmap.pg_ps_enabled=1 # Usefull if you are using Intel-Gigabit NIC #hw.em.rxd=4096 #hw.em.txd=4096 #hw.em.rx_process_limit="-1" # Also if you have ALOT interrupts on NIC - play with following parameters # NOTE: You should set them for every NIC #dev.em.0.rx_int_delay: 250 #dev.em.0.tx_int_delay: 250 #dev.em.0.rx_abs_int_delay: 250 #dev.em.0.tx_abs_int_delay: 250 # There is also multithreaded version of em/igb drivers can be found here: # http://people.yandex-team.ru/~wawa/ # # for additional em monitoring and statistics use # sysctl dev.em.0.stats=1 ; dmesg # sysctl dev.em.0.debug=1 ; dmesg # Also after r209242 (-CURRENT) there is a separate sysctl for each stat variable; # Same tunings for igb #hw.igb.rxd=4096 #hw.igb.txd=4096 #hw.igb.rx_process_limit=100 # Some useful netisr tunables. See sysctl net.isr #net.isr.maxthreads=4 #net.isr.defaultqlimit=4096 #net.isr.maxqlimit: 10240 # Bind netisr threads to CPUs #net.isr.bindthreads=1 # # FreeBSD 9.x+ # Increase interface send queue length # See commit message http://svn.freebsd.org/viewvc/base?view=revision&revision=207554 #net.link.ifqmaxlen=1024 # Nicer boot logo =) loader_logo="beastie" And finally here is KERNCONF: # Just some of them, see also # cat /sys/{i386,amd64,}/conf/NOTES # This one useful only on i386 #options KVA_PAGES=512 # You can play with HZ in environments with high interrupt rate (default is 1000) # 100 is for my notebook to prolong it's battery life #options HZ=100 # Polling is goot on network loads with high packet rates and low-end NICs # NB! Do not enable it if you want more than one netisr thread #options DEVICE_POLLING # Eliminate datacopy on socket read-write # To take advantage with zero copy sockets you should have an MTU >= 4k # This req. is only for receiving data. # Read more in man zero_copy_sockets # Also this epic thread on kernel trap: # http://kerneltrap.org/node/6506 # Here Linus says that "anybody that does it that way (FreeBSD) is totally incompetent" #options ZERO_COPY_SOCKETS # Support TCP sign. Used for IPSec options TCP_SIGNATURE # There was stackoverflow found in KAME IPSec stack: # See http://secunia.com/advisories/43995/ # For quick workaround you can use `ipfw add deny proto ipcomp` options IPSEC # This ones can be loaded as modules. They described in loader.conf section #options ACCEPT_FILTER_DATA #options ACCEPT_FILTER_HTTP # Adding ipfw, also can be loaded as modules options IPFIREWALL # On 8.1+ you can disable verbose to see blocked packets on ipfw0 interface. # Also there is no point in compiling verbose into the kernel, because # now there is net.inet.ip.fw.verbose tunable. #options IPFIREWALL_VERBOSE #options IPFIREWALL_VERBOSE_LIMIT=10 options IPFIREWALL_FORWARD # Adding kernel NAT options IPFIREWALL_NAT options LIBALIAS # Traffic shaping options DUMMYNET # Divert, i.e. for userspace NAT options IPDIVERT # This is for OpenBSD's pf firewall device pf device pflog # pf's QoS - ALTQ options ALTQ options ALTQ_CBQ # Class Bases Queuing (CBQ) options ALTQ_RED # Random Early Detection (RED) options ALTQ_RIO # RED In/Out options ALTQ_HFSC # Hierarchical Packet Scheduler (HFSC) options ALTQ_PRIQ # Priority Queuing (PRIQ) options ALTQ_NOPCC # Required for SMP build # Pretty console # Manual can be found here http://forums.freebsd.org/showthread.php?t=6134 #options VESA #options SC_PIXEL_MODE # Disable reboot on Ctrl Alt Del #options SC_DISABLE_REBOOT # Change normal|kernel messages color options SC_NORM_ATTR=(FG_GREEN|BG_BLACK) options SC_KERNEL_CONS_ATTR=(FG_YELLOW|BG_BLACK) # More scroll space options SC_HISTORY_SIZE=8192 # Adding hardware crypto device device crypto device cryptodev # Useful network interfaces device vlan device tap #Virtual Ethernet driver device gre #IP over IP tunneling device if_bridge #Bridge interface device pfsync #synchronization interface for PF device carp #Common Address Redundancy Protocol device enc #IPsec interface device lagg #Link aggregation interface device stf #IPv4-IPv6 port # Also for my notebook, but may be used with Opteron device amdtemp # Same for Intel processors device coretemp # man 4 cpuctl device cpuctl # CPU control pseudo-device # Support for ECMP. More than one route for destination # Works even with default route so one can use it as LB for two ISP # For now code is unstable and panics (panic: rtfree 2) on route deletions. #options RADIX_MPATH # Multicast routing #options MROUTING #options PIM # Debug & DTrace options KDB # Kernel debugger related code options KDB_TRACE # Print a stack trace for a panic options KDTRACE_FRAME # amd64-only(?) options KDTRACE_HOOKS # all architectures - enable general DTrace hooks #options DDB #options DDB_CTF # all architectures - kernel ELF linker loads CTF data # Adaptive spining in lockmgr (8.x+) # See http://www.mail-archive.com/[email protected]/msg10782.html options ADAPTIVE_LOCKMGRS # UTF-8 in console (8.x+) #options TEKEN_UTF8 # FreeBSD 8.1+ # Deadlock resolver thread # For additional information see http://www.mail-archive.com/[email protected]/msg18124.html # (FYI: "resolution" is panic so use with caution) #options DEADLKRES # Increase maximum size of Raw I/O and sendfile(2) readahead #options MAXPHYS=(1024*1024) #options MAXBSIZE=(1024*1024) # For scheduler debug enable following option. # Debug will be available via `kern.sched.stats` sysctl # For more information see http://svnweb.freebsd.org/base/head/sys/conf/NOTES?view=markup #options SCHED_STATS If you are tuning network for maximum performance you may wish to play with ifconfig options like: # You can list all capabilities via `ifconfig -m` ifconfig [-]rxcsum [-]txcsum [-]tso [-]lro mtu In case you've enabled DDB in kernel config, you should edit your /etc/ddb.conf and add something like this to enable automatic reboot (and textdump as bonus): script kdb.enter.panic=textdump set; capture on; show pcpu; bt; ps; alltrace; capture off; call doadump; reset script kdb.enter.default=textdump set; capture on; bt; ps; capture off; call doadump; reset And do not forget to add ddb_enable="YES" to /etc/rc.conf Since FreeBSD 9 you can select to enable/disable flowcontrol on your NIC: # See http://en.wikipedia.org/wiki/Ethernet_flow_control and # http://www.mail-archive.com/[email protected]/msg07927.html for additional info ifconfig bge0 media auto mediaopt flowcontrol PS. Also most of FreeBSD's limits can be monitored by # vmstat -z and # limits PPS. variety of network counters can be monitored via # netstat -s In FreeBSD-9 netstat's -Q option appeared, try following command to display netisr stats # netstat -Q PPPS. also see # man 7 tuning PPPPS. I wanted to thank FreeBSD community, especially author of nginx - Igor Sysoev, nginx-ru@ and FreeBSD-performance@ mailing lists for providing useful information about FreeBSD tuning. FreeBSD WIP * Whats cooking for FreeBSD 7? * Whats cooking for FreeBSD 8? * Whats cooking for FreeBSD 9? So here is the question: What tunings are you using on yours FreeBSD servers? You can also post your /etc/sysctl.conf, /boot/loader.conf, kernel options, etc with description of its' meaning (do not copy-paste from sysctl -d). Don't forget to specify server type (web, smb, gateway, etc) Let's share experience!

  Read the article

• Slow NFS and GFS2 performance

  - by Tiago

  Recently I've designed and configured a 4 node cluster for a webapp that does lots of file handling. The cluster have been broken down into 2 main roles, webserver and storage. Each role is replicated to a second server using drbd in active/passive mode. The webserver does a NFS mount of the data directory of the storage server and the latter also has a webserver running to serve files to browser clients. In the storage servers I've created a GFS2 FS to hold the data which is wired to drbd. I've chose GFS2 mainly because the announced performance and also because the volume size which has to be pretty high. Since we entered production I've been facing two problems that I think are deeply connected. First of all, the NFS mount on the webservers keeps hanging for a minute or so and then resumes normal operations. By analyzing the logs I've found out that NFS stops answering for a while and outputs the following log lines: Oct 15 18:15:42 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:44 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:46 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:47 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:47 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:47 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:48 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:48 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:51 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:52 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:52 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:55 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:55 <server hostname> kernel: nfs: server active.storage.vlan not responding, still trying Oct 15 18:15:58 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK Oct 15 18:15:59 <server hostname> kernel: nfs: server active.storage.vlan OK In this case, the hang lasted for 16 seconds but sometimes it takes 1 or 2 minutes to resume normal operations. My first guess was this was happening due to heavy load of the NFS mount and that by increasing RPCNFSDCOUNT to a higher value, this would become stable. I've increased it several times and apparently, after a while, the logs started appearing less times. The value is now on 32. After further investigating the issue, I've came across a different hang, despite the NFS messages still appear in the logs. Sometimes, the GFS2 FS simply hangs which causes both the NFS and the storage webserver to serve files. Both stay hang for a while and then they resume normal operations. This hangs leaves no trace on client side (also leaves no NFS ... not responding messages) and, on the storage side, the log system appears to be empty, even though the rsyslogd is running. The nodes connect themselves through a 10Gbps non-dedicated connection but I don't think this is an issue because the GFS2 hang is confirmed but connecting directly to the active storage server. I've been trying to solve this for a while now and I've tried different NFS configuration options, before I've found out the GFS2 FS is also hanging. The NFS mount is exported as such: /srv/data/ <ip_address>(rw,async,no_root_squash,no_all_squash,fsid=25) And the NFS client mounts with: mount -o "async,hard,intr,wsize=8192,rsize=8192" active.storage.vlan:/srv/data /srv/data After some tests, these were the configurations that yielded more performance to the cluster. I am desperate to find a solution for this as the cluster is already in production mode and I need to fix this so that this hangs won't happen in the future and I don't really know for sure what and how I should be benchmarking. What I can tell is that this is happening due to heavy loads as I have tested the cluster earlier and this problems weren't happening at all. Please tell me if you need me to provide configuration details of the cluster, and which do you want me to post. As last resort I can migrate the files to a different FS but I need some solid pointers on whether this will solve this problems as the volume size is extremely large at this point. The servers are being hosted by a third-party enterprise and I don't have physical access to them. Best regards. EDIT 1: The servers are physical servers and their specs are: Webservers: Intel Bi Xeon E5606 2x4 2.13GHz 24GB DDR3 Intel SSD 320 2 x 120GB Raid 1 Storage: Intel i5 3550 3.3GHz 16GB DDR3 12 x 2TB SATA Initially there was a VRack setup between the servers but we've upgraded one of the storage servers to have more RAM and it wasn't inside the VRack. They connect through a shared 10Gbps connection between them. Please note that it is the same connection that is used for public access. They use a single IP (using IP Failover) to connect between them and to allow for a graceful failover. NFS is therefore over a public connection and not under any private network (it was before the upgrade, were the problem still existed). The firewall was configured and tested thoroughly but I disabled it for a while to see if the problem still occurred, and it did. From my knowledge the hosting provider isn't blocking or limiting the connection between either the servers and the public domain (at least under a given bandwidth consumption threshold that hasn't been reached yet). Hope this helps figuring out the problem. EDIT 2: Relevant software versions: CentOS 2.6.32-279.9.1.el6.x86_64 nfs-utils-1.2.3-26.el6.x86_64 nfs-utils-lib-1.1.5-4.el6.x86_64 gfs2-utils-3.0.12.1-32.el6_3.1.x86_64 kmod-drbd84-8.4.2-1.el6_3.elrepo.x86_64 drbd84-utils-8.4.2-1.el6.elrepo.x86_64 DRBD configuration on storage servers: #/etc/drbd.d/storage.res resource storage { protocol C; on <server1 fqdn> { device /dev/drbd0; disk /dev/vg_storage/LV_replicated; address <server1 ip>:7788; meta-disk internal; } on <server2 fqdn> { device /dev/drbd0; disk /dev/vg_storage/LV_replicated; address <server2 ip>:7788; meta-disk internal; } } NFS Configuration in storage servers: #/etc/sysconfig/nfs RPCNFSDCOUNT=32 STATD_PORT=10002 STATD_OUTGOING_PORT=10003 MOUNTD_PORT=10004 RQUOTAD_PORT=10005 LOCKD_UDPPORT=30001 LOCKD_TCPPORT=30001 (can there be any conflict in using the same port for both LOCKD_UDPPORT and LOCKD_TCPPORT?) GFS2 configuration: # gfs2_tool gettune <mountpoint> incore_log_blocks = 1024 log_flush_secs = 60 quota_warn_period = 10 quota_quantum = 60 max_readahead = 262144 complain_secs = 10 statfs_slow = 0 quota_simul_sync = 64 statfs_quantum = 30 quota_scale = 1.0000 (1, 1) new_files_jdata = 0 Storage network environment: eth0 Link encap:Ethernet HWaddr <mac address> inet addr:<ip address> Bcast:<bcast address> Mask:<ip mask> inet6 addr: <ip address> Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:957025127 errors:0 dropped:0 overruns:0 frame:0 TX packets:1473338731 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2630984979622 (2.3 TiB) TX bytes:1648430431523 (1.4 TiB) eth0:0 Link encap:Ethernet HWaddr <mac address> inet addr:<ip failover address> Bcast:<bcast address> Mask:<ip mask> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 The IP addresses are statically assigned with the given network configurations: DEVICE="eth0" BOOTPROTO="static" HWADDR=<mac address> ONBOOT="yes" TYPE="Ethernet" IPADDR=<ip address> NETMASK=<net mask> and DEVICE="eth0:0" BOOTPROTO="static" HWADDR=<mac address> IPADDR=<ip failover> NETMASK=<net mask> ONBOOT="yes" BROADCAST=<bcast address> Hosts file to allow for a graceful NFS failover in conjunction with NFS option fsid=25 set on both storage servers: #/etc/hosts <storage ip failover address> active.storage.vlan <webserver ip failover address> active.service.vlan As you can see, packet errors are down to 0. I've also ran ping for a long time without any packet loss. MTU size is the normal 1500. As there is no VLan by now, this is the MTU used to communicate between servers. The webservers' network environment is similar. One thing I forgot to mention is that the storage servers handle ~200GB of new files each day through the NFS connection, which is a key point for me to think this is some kind of heavy load problem with either NFS or GFS2. If you need further configuration details please tell me. EDIT 3: Earlier today we had a major filesystem crash on the storage server. I couldn't get the details of the crash right away because the server stop responding. After the reboot, I noticed the filesystem was extremely slow, and I was not being able to serve a single file through either NFS or httpd, perhaps due to cache warming or so. Nevertheless, I've been monitoring the server closely and the following error came up in dmesg. The source of the problem is clearly GFS, which is waiting for a lock and ends up starving after a while. INFO: task nfsd:3029 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. nfsd D 0000000000000000 0 3029 2 0x00000080 ffff8803814f79e0 0000000000000046 0000000000000000 ffffffff8109213f ffff880434c5e148 ffff880624508d88 ffff8803814f7960 ffffffffa037253f ffff8803815c1098 ffff8803814f7fd8 000000000000fb88 ffff8803815c1098 Call Trace: [<ffffffff8109213f>] ? wake_up_bit+0x2f/0x40 [<ffffffffa037253f>] ? gfs2_holder_wake+0x1f/0x30 [gfs2] [<ffffffff814ff42e>] __mutex_lock_slowpath+0x13e/0x180 [<ffffffff814ff2cb>] mutex_lock+0x2b/0x50 [<ffffffffa0379f21>] gfs2_log_reserve+0x51/0x190 [gfs2] [<ffffffffa0390da2>] gfs2_trans_begin+0x112/0x1d0 [gfs2] [<ffffffffa0369b05>] ? gfs2_dir_check+0x35/0xe0 [gfs2] [<ffffffffa0377943>] gfs2_createi+0x1a3/0xaa0 [gfs2] [<ffffffff8121aab1>] ? avc_has_perm+0x71/0x90 [<ffffffffa0383d1e>] gfs2_create+0x7e/0x1a0 [gfs2] [<ffffffffa037783f>] ? gfs2_createi+0x9f/0xaa0 [gfs2] [<ffffffff81188cf4>] vfs_create+0xb4/0xe0 [<ffffffffa04217d6>] nfsd_create_v3+0x366/0x4c0 [nfsd] [<ffffffffa0429703>] nfsd3_proc_create+0x123/0x1b0 [nfsd] [<ffffffffa041a43e>] nfsd_dispatch+0xfe/0x240 [nfsd] [<ffffffffa025a5d4>] svc_process_common+0x344/0x640 [sunrpc] [<ffffffff810602a0>] ? default_wake_function+0x0/0x20 [<ffffffffa025ac10>] svc_process+0x110/0x160 [sunrpc] [<ffffffffa041ab62>] nfsd+0xc2/0x160 [nfsd] [<ffffffffa041aaa0>] ? nfsd+0x0/0x160 [nfsd] [<ffffffff81091de6>] kthread+0x96/0xa0 [<ffffffff8100c14a>] child_rip+0xa/0x20 [<ffffffff81091d50>] ? kthread+0x0/0xa0 [<ffffffff8100c140>] ? child_rip+0x0/0x20

  Read the article

• PC hangs and reboots from time to time

  - by Bevor

  Hello, I have a very strange problem: Since I have my new PC, I have always had problems with it. From time to time the computer freezes for some seconds and suddendly reboots by itself. I've had this problem since Ubuntu 9.10. The same with 10.04 and 10.10. That's why I don't think it's a software failure because the problem persist too long. It doesn't have anything to do with what I'm doing at this time. Sometimes I listen to music, sometimes I only use Firefox, sometimes I'm running 2 or 3 VMs, sometimes I watch DVD. So it's not isolatable. I could freeze once a day or once a week. I put the PC to the vendor twice(!). The first time they changed my power supply but the problem persisted. The second time they told me that they made some heavy performance tests 50 hours long but they didn't find anything. (How can that be that I have daily freezes with normal usage). The vendor didn't check the hard discs because they used their own disc with Windows. (So they never checked the Linux installation). Yesterday I made some intensive hard disc scans with "SMART" but no errors were found. I ran memtest for 3 times but no errors found. I already had this problem in my old flat, so I doubt that I has something to do with current fluctuation. I already tried another electrical socket and changed to connector strip but the problem persists. At the moment I removed 2 of the RAMs (2x 2GB). In all I have 6GB, 2x2GB and 2x1GB. Could this difference maybe be a problem? Here is a list of my components. I hope that anybody find something I didn't think about yet. And here a list of my components: 1x AMD Phenom II X4 965 Black Edition, 3,4Ghz, Quad Core, S-AM3, Boxed 2x DDR3-RAM 2048MB, PC3-1333 Mhz, CL9, Kingston ValueRAM 2x DDR3-RAM 1024MB, PC3-1333 Mhz, CL9, Kingston ValueRAM 2x SATA II Seagate Barracuda 7200.12, 1TB 32MB Cache = RAID 1 1x DVD ROM SATA LG DH16NSR, 16x/52x 1x DVD-+R/-+RW SATA LG GH-22NS50 1x Cardreader 18in1 1x PCI-E 2.0 GeForce GTS 250, Retail, 1024MB 1x Power Supply ATX 400 Watt, CHIEFTEC APS-400S, 80 Plus 1x Network card PCI Intel PRO/1000GT 10/100/1000 MBit 1x Mainboard Socket-AM3 ASUS M4A79XTD EVO, ATX lshw: description: Desktop Computer product: System Product Name vendor: System manufacturer version: System Version serial: System Serial Number width: 64 bits capabilities: smbios-2.5 dmi-2.5 vsyscall64 vsyscall32 configuration: boot=normal chassis=desktop uuid=80E4001E-8C00-002C-AA59-E0CB4EBAC29A *-core description: Motherboard product: M4A79XTD EVO vendor: ASUSTeK Computer INC. physical id: 0 version: Rev X.0X serial: MT709CK11101196 slot: To Be Filled By O.E.M. *-firmware description: BIOS vendor: American Megatrends Inc. physical id: 0 version: 0704 (11/25/2009) size: 64KiB capacity: 960KiB capabilities: isa pci pnp apm upgrade shadowing escd cdboot bootselect socketedrom edd int13floppy1200 int13floppy720 int13floppy2880 int5printscreen int9keyboard int14serial int17printer int10video acpi usb ls120boot zipboot biosbootspecification *-cpu description: CPU product: AMD Phenom(tm) II X4 965 Processor vendor: Advanced Micro Devices [AMD] physical id: 4 bus info: cpu@0 version: AMD Phenom(tm) II X4 965 Processor serial: To Be Filled By O.E.M. slot: AM3 size: 800MHz capacity: 3400MHz width: 64 bits clock: 200MHz capabilities: fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp x86-64 3dnowext 3dnow constant_tsc rep_good nonstop_tsc extd_apicid pni monitor cx16 popcnt lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs skinit wdt npt lbrv svm_lock nrip_save cpufreq *-cache:0 description: L1 cache physical id: 5 slot: L1-Cache size: 512KiB capacity: 512KiB capabilities: pipeline-burst internal varies data *-cache:1 description: L2 cache physical id: 6 slot: L2-Cache size: 2MiB capacity: 2MiB capabilities: pipeline-burst internal varies unified *-cache:2 description: L3 cache physical id: 7 slot: L3-Cache size: 6MiB capacity: 6MiB capabilities: pipeline-burst internal varies unified *-memory description: System Memory physical id: 36 slot: System board or motherboard size: 2GiB *-bank:0 description: DIMM Synchronous 1333 MHz (0.8 ns) product: ModulePartNumber00 vendor: Manufacturer00 physical id: 0 serial: SerNum00 slot: DIMM0 size: 1GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:1 description: DIMM Synchronous 1333 MHz (0.8 ns) product: ModulePartNumber01 vendor: Manufacturer01 physical id: 1 serial: SerNum01 slot: DIMM1 size: 1GiB width: 64 bits clock: 1333MHz (0.8ns) *-bank:2 description: DIMM [empty] product: ModulePartNumber02 vendor: Manufacturer02 physical id: 2 serial: SerNum02 slot: DIMM2 *-bank:3 description: DIMM [empty] product: ModulePartNumber03 vendor: Manufacturer03 physical id: 3 serial: SerNum03 slot: DIMM3 *-pci:0 description: Host bridge product: RD780 Northbridge only dual slot PCI-e_GFX and HT1 K8 part vendor: ATI Technologies Inc physical id: 100 bus info: pci@0000:00:00.0 version: 00 width: 32 bits clock: 66MHz *-pci:0 description: PCI bridge product: RD790 PCI to PCI bridge (external gfx0 port A) vendor: ATI Technologies Inc physical id: 2 bus info: pci@0000:00:02.0 version: 00 width: 32 bits clock: 33MHz capabilities: pci pm pciexpress msi ht normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:40 ioport:a000(size=4096) memory:f8000000-fbbfffff ioport:d0000000(size=268435456) *-display description: VGA compatible controller product: G92 [GeForce GTS 250] vendor: nVidia Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a2 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:18 memory:fa000000-faffffff memory:d0000000-dfffffff memory:f8000000-f9ffffff ioport:ac00(size=128) memory:fbbe0000-fbbfffff *-pci:1 description: PCI bridge product: RD790 PCI to PCI bridge (PCI express gpp port C) vendor: ATI Technologies Inc physical id: 6 bus info: pci@0000:00:06.0 version: 00 width: 32 bits clock: 33MHz capabilities: pci pm pciexpress msi ht normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:41 ioport:b000(size=4096) memory:fbc00000-fbcfffff ioport:f6f00000(size=1048576) *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 03 serial: e0:cb:4e:ba:c2:9a size: 10MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:45 ioport:b800(size=256) memory:f6fff000-f6ffffff memory:f6ff8000-f6ffbfff memory:fbcf0000-fbcfffff *-pci:2 description: PCI bridge product: RD790 PCI to PCI bridge (PCI express gpp port D) vendor: ATI Technologies Inc physical id: 7 bus info: pci@0000:00:07.0 version: 00 width: 32 bits clock: 33MHz capabilities: pci pm pciexpress msi ht normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:42 ioport:c000(size=4096) memory:fbd00000-fbdfffff *-firewire description: FireWire (IEEE 1394) product: VT6315 Series Firewire Controller vendor: VIA Technologies, Inc. physical id: 0 bus info: pci@0000:03:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress ohci bus_master cap_list configuration: driver=firewire_ohci latency=0 resources: irq:19 memory:fbdff800-fbdfffff ioport:c800(size=256) *-pci:3 description: PCI bridge product: RD790 PCI to PCI bridge (PCI express gpp port E) vendor: ATI Technologies Inc physical id: 9 bus info: pci@0000:00:09.0 version: 00 width: 32 bits clock: 33MHz capabilities: pci pm pciexpress msi ht normal_decode bus_master cap_list configuration: driver=pcieport resources: irq:43 ioport:d000(size=4096) memory:fbe00000-fbefffff *-ide description: IDE interface product: 88SE6121 SATA II Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:04:00.0 version: b2 width: 32 bits clock: 33MHz capabilities: ide pm msi pciexpress bus_master cap_list configuration: driver=pata_marvell latency=0 resources: irq:17 ioport:dc00(size=8) ioport:d880(size=4) ioport:d800(size=8) ioport:d480(size=4) ioport:d400(size=16) memory:fbeffc00-fbefffff *-storage description: SATA controller product: SB700/SB800 SATA Controller [IDE mode] vendor: ATI Technologies Inc physical id: 11 bus info: pci@0000:00:11.0 logical name: scsi0 logical name: scsi2 version: 00 width: 32 bits clock: 66MHz capabilities: storage msi ahci_1.0 bus_master cap_list emulated configuration: driver=ahci latency=64 resources: irq:44 ioport:9000(size=8) ioport:8000(size=4) ioport:7000(size=8) ioport:6000(size=4) ioport:5000(size=16) memory:f7fffc00-f7ffffff *-disk:0 description: ATA Disk product: ST31000528AS vendor: Seagate physical id: 0 bus info: scsi@0:0.0.0 logical name: /dev/sda version: CC38 serial: 9VP3WD9Z size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=000ad206 *-volume:0 UNCLAIMED description: Linux filesystem partition vendor: Linux physical id: 1 bus info: scsi@0:0.0.0,1 version: 1.0 serial: 81839235-21ea-4853-90a4-814779f49000 size: 972MiB capacity: 972MiB capabilities: primary ext2 initialized configuration: filesystem=ext2 modified=2010-12-06 18:32:58 mounted=2010-11-01 07:05:10 state=unknown *-volume:1 UNCLAIMED description: Linux swap volume physical id: 2 bus info: scsi@0:0.0.0,2 version: 1 serial: 22b881d5-6f5c-484d-94e8-e231896fa91b size: 486MiB capacity: 486MiB capabilities: primary nofs swap initialized configuration: filesystem=swap pagesize=4096 *-volume:2 UNCLAIMED description: EXT3 volume vendor: Linux physical id: 3 bus info: scsi@0:0.0.0,3 version: 1.0 serial: ad5b0daf-11e8-4f8f-8598-4e89da9c0d84 size: 47GiB capacity: 47GiB capabilities: primary journaled extended_attributes large_files recover ext3 ext2 initialized configuration: created=2010-02-16 20:42:29 filesystem=ext3 modified=2010-11-29 17:02:34 mounted=2010-12-06 18:32:50 state=clean *-volume:3 UNCLAIMED description: Extended partition physical id: 4 bus info: scsi@0:0.0.0,4 size: 882GiB capacity: 882GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume UNCLAIMED description: Linux filesystem partition physical id: 5 capacity: 882GiB *-disk:1 description: ATA Disk product: ST31000528AS vendor: Seagate physical id: 1 bus info: scsi@2:0.0.0 logical name: /dev/sdb version: CC38 serial: 9VP3SCPF size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=000ad206 *-volume:0 UNCLAIMED description: Linux filesystem partition vendor: Linux physical id: 1 bus info: scsi@2:0.0.0,1 version: 1.0 serial: 81839235-21ea-4853-90a4-814779f49000 size: 972MiB capacity: 972MiB capabilities: primary ext2 initialized configuration: filesystem=ext2 modified=2010-12-06 18:32:58 mounted=2010-11-01 07:05:10 state=unknown *-volume:1 UNCLAIMED description: Linux swap volume physical id: 2 bus info: scsi@2:0.0.0,2 version: 1 serial: 22b881d5-6f5c-484d-94e8-e231896fa91b size: 486MiB capacity: 486MiB capabilities: primary nofs swap initialized configuration: filesystem=swap pagesize=4096 *-volume:2 UNCLAIMED description: EXT3 volume vendor: Linux physical id: 3 bus info: scsi@2:0.0.0,3 version: 1.0 serial: ad5b0daf-11e8-4f8f-8598-4e89da9c0d84 size: 47GiB capacity: 47GiB capabilities: primary journaled extended_attributes large_files recover ext3 ext2 initialized configuration: created=2010-02-16 20:42:29 filesystem=ext3 modified=2010-11-29 17:02:34 mounted=2010-12-06 18:32:50 state=clean *-volume:3 UNCLAIMED description: Extended partition physical id: 4 bus info: scsi@2:0.0.0,4 size: 882GiB capacity: 882GiB capabilities: primary extended partitioned partitioned:extended *-logicalvolume UNCLAIMED description: Linux filesystem partition physical id: 5 capacity: 882GiB *-usb:0 description: USB Controller product: SB700/SB800 USB OHCI0 Controller vendor: ATI Technologies Inc physical id: 12 bus info: pci@0000:00:12.0 version: 00 width: 32 bits clock: 66MHz capabilities: ohci bus_master configuration: driver=ohci_hcd latency=64 resources: irq:16 memory:f7ffd000-f7ffdfff *-usb:1 description: USB Controller product: SB700 USB OHCI1 Controller vendor: ATI Technologies Inc physical id: 12.1 bus info: pci@0000:00:12.1 version: 00 width: 32 bits clock: 66MHz capabilities: ohci bus_master configuration: driver=ohci_hcd latency=64 resources: irq:16 memory:f7ffe000-f7ffefff *-usb:2 description: USB Controller product: SB700/SB800 USB EHCI Controller vendor: ATI Technologies Inc physical id: 12.2 bus info: pci@0000:00:12.2 version: 00 width: 32 bits clock: 66MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=64 resources: irq:17 memory:f7fff800-f7fff8ff *-usb:3 description: USB Controller product: SB700/SB800 USB OHCI0 Controller vendor: ATI Technologies Inc physical id: 13 bus info: pci@0000:00:13.0 version: 00 width: 32 bits clock: 66MHz capabilities: ohci bus_master configuration: driver=ohci_hcd latency=64 resources: irq:18 memory:f7ffb000-f7ffbfff *-usb:4 description: USB Controller product: SB700 USB OHCI1 Controller vendor: ATI Technologies Inc physical id: 13.1 bus info: pci@0000:00:13.1 version: 00 width: 32 bits clock: 66MHz capabilities: ohci bus_master configuration: driver=ohci_hcd latency=64 resources: irq:18 memory:f7ffc000-f7ffcfff *-usb:5 description: USB Controller product: SB700/SB800 USB EHCI Controller vendor: ATI Technologies Inc physical id: 13.2 bus info: pci@0000:00:13.2 version: 00 width: 32 bits clock: 66MHz capabilities: pm debug ehci bus_master cap_list configuration: driver=ehci_hcd latency=64 resources: irq:19 memory:f7fff400-f7fff4ff *-serial UNCLAIMED description: SMBus product: SBx00 SMBus Controller vendor: ATI Technologies Inc physical id: 14 bus info: pci@0000:00:14.0 version: 3c width: 32 bits clock: 66MHz capabilities: ht cap_list configuration: latency=0 *-ide description: IDE interface product: SB700/SB800 IDE Controller vendor: ATI Technologies Inc physical id: 14.1 bus info: pci@0000:00:14.1 logical name: scsi5 version: 00 width: 32 bits clock: 66MHz capabilities: ide msi bus_master cap_list emulated configuration: driver=pata_atiixp latency=64 resources: irq:16 ioport:1f0(size=8) ioport:3f6 ioport:170(size=8) ioport:376 ioport:ff00(size=16) *-cdrom:0 description: DVD reader product: DVDROM DH16NS30 vendor: HL-DT-ST physical id: 0.0.0 bus info: scsi@5:0.0.0 logical name: /dev/cdrom1 logical name: /dev/dvd1 logical name: /dev/scd0 logical name: /dev/sr0 version: 1.00 capabilities: removable audio dvd configuration: ansiversion=5 status=nodisc *-cdrom:1 description: DVD-RAM writer product: DVDRAM GH22NS50 vendor: HL-DT-ST physical id: 0.1.0 bus info: scsi@5:0.1.0 logical name: /dev/cdrom logical name: /dev/cdrw logical name: /dev/dvd logical name: /dev/dvdrw logical name: /dev/scd1 logical name: /dev/sr1 version: TN02 capabilities: removable audio cd-r cd-rw dvd dvd-r dvd-ram configuration: ansiversion=5 status=nodisc *-multimedia description: Audio device product: SBx00 Azalia (Intel HDA) vendor: ATI Technologies Inc physical id: 14.2 bus info: pci@0000:00:14.2 version: 00 width: 64 bits clock: 33MHz capabilities: pm bus_master cap_list configuration: driver=HDA Intel latency=64 resources: irq:16 memory:f7ff4000-f7ff7fff *-isa description: ISA bridge product: SB700/SB800 LPC host controller vendor: ATI Technologies Inc physical id: 14.3 bus info: pci@0000:00:14.3 version: 00 width: 32 bits clock: 66MHz capabilities: isa bus_master configuration: latency=0 *-pci:4 description: PCI bridge product: SBx00 PCI to PCI Bridge vendor: ATI Technologies Inc physical id: 14.4 bus info: pci@0000:00:14.4 version: 00 width: 32 bits clock: 66MHz capabilities: pci subtractive_decode bus_master resources: ioport:e000(size=4096) memory:fbf00000-fbffffff *-network description: Ethernet interface product: 82541PI Gigabit Ethernet Controller vendor: Intel Corporation physical id: 5 bus info: pci@0000:05:05.0 logical name: eth1 version: 05 serial: 00:1b:21:56:f3:60 size: 100MB/s capacity: 1GB/s width: 32 bits clock: 66MHz capabilities: pm pcix bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000 driverversion=7.3.21-k6-NAPI duplex=full firmware=N/A ip=192.168.1.2 latency=64 link=yes mingnt=255 multicast=yes port=twisted pair speed=100MB/s resources: irq:20 memory:fbfe0000-fbffffff memory:fbfc0000-fbfdffff ioport:ec00(size=64) memory:fbfa0000-fbfbffff *-usb:6 description: USB Controller product: SB700/SB800 USB OHCI2 Controller vendor: ATI Technologies Inc physical id: 14.5 bus info: pci@0000:00:14.5 version: 00 width: 32 bits clock: 66MHz capabilities: ohci bus_master configuration: driver=ohci_hcd latency=64 resources: irq:18 memory:f7ffa000-f7ffafff *-pci:1 description: Host bridge product: Family 10h Processor HyperTransport Configuration vendor: Advanced Micro Devices [AMD] physical id: 101 bus info: pci@0000:00:18.0 version: 00 width: 32 bits clock: 33MHz *-pci:2 description: Host bridge product: Family 10h Processor Address Map vendor: Advanced Micro Devices [AMD] physical id: 102 bus info: pci@0000:00:18.1 version: 00 width: 32 bits clock: 33MHz *-pci:3 description: Host bridge product: Family 10h Processor DRAM Controller vendor: Advanced Micro Devices [AMD] physical id: 103 bus info: pci@0000:00:18.2 version: 00 width: 32 bits clock: 33MHz *-pci:4 description: Host bridge product: Family 10h Processor Miscellaneous Control vendor: Advanced Micro Devices [AMD] physical id: 104 bus info: pci@0000:00:18.3 version: 00 width: 32 bits clock: 33MHz configuration: driver=k10temp resources: irq:0 *-pci:5 description: Host bridge product: Family 10h Processor Link Control vendor: Advanced Micro Devices [AMD] physical id: 105 bus info: pci@0000:00:18.4 version: 00 width: 32 bits clock: 33MHz *-scsi physical id: 1 bus info: usb@2:3 logical name: scsi8 capabilities: emulated scsi-host configuration: driver=usb-storage *-disk:0 description: SCSI Disk physical id: 0.0.0 bus info: scsi@8:0.0.0 logical name: /dev/sdc *-disk:1 description: SCSI Disk physical id: 0.0.1 bus info: scsi@8:0.0.1 logical name: /dev/sdd *-disk:2 description: SCSI Disk physical id: 0.0.2 bus info: scsi@8:0.0.2 logical name: /dev/sde *-disk:3 description: SCSI Disk physical id: 0.0.3 bus info: scsi@8:0.0.3 logical name: /dev/sdf *-network DISABLED description: Ethernet interface physical id: 1 logical name: vboxnet0 serial: 0a:00:27:00:00:00 capabilities: ethernet physical configuration: broadcast=yes multicast=yes

  Read the article

• Ping "replies" from same computer with 'Destination host unreachable' (no route to other computer)

  - by Srekel

  I've got two computers in a LAN behind a wireless router. One has XP with ip 192.168.1.2 This one has W7 with ip 192.168.1.7 If I try to ping the other one from this computer, I get this: C:\Users\Srekel>ping 192.168.1.2 Pinging 192.168.1.2 with 32 bytes of data: Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Reply from 192.168.1.7: Destination host unreachable. Ping statistics for 192.168.1.2: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Tracert gives the same result: C:\Users\Srekel>tracert 192.168.1.2 Tracing route to 192.168.1.2 over a maximum of 30 hops 1 Kakburken4 [192.168.1.7] reports: Destination host unreachable. Trace complete. Although I can ping and tracert the router without any problems. I have disabled the firewalls on both computers. The router is set to use DHCP (if that matters). Here is the output from "route". C:\Users\Srekel>route print =========================================================================== Interface List 13...00 25 86 df c6 89 ......TP-LINK Wireless N Adapter 12...e0 cb 4e 26 b9 84 ......Realtek PCIe GBE Family Controller #2 11...e0 cb 4e 26 be 94 ......Realtek PCIe GBE Family Controller 1...........................Software Loopback Interface 1 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 14...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.7 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.7 276 192.168.1.7 255.255.255.255 On-link 192.168.1.7 276 192.168.1.255 255.255.255.255 On-link 192.168.1.7 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.7 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.7 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 14 58 ::/0 On-link 1 306 ::1/128 On-link 14 58 2001::/32 On-link 14 306 2001:0:5ef5:73ba:881:20c1:3f57:fef8/128 On-link 14 306 fe80::/64 On-link 14 306 fe80::881:20c1:3f57:fef8/128 On-link 1 306 ff00::/8 On-link 14 306 ff00::/8 On-link =========================================================================== Persistent Routes: None I've set up and debugged a few networks in my life but I'm not really an advanced network user, so I'm not sure what might be wrong. Any ideas? Oh, and pinging this computer from the other computer doesn't work either. EDIT: Adding arp output: C:\Users\Srekel>arp -a Interface: 192.168.1.7 --- 0xd Internet Address Physical Address Type 192.168.1.1 00-1f-33-ef-28-01 dynamic 192.168.1.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Adding ipconfig... C:\Users\Srekel>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : Kakburken4 Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : TP-LINK Wireless N Adapter Physical Address. . . . . . . . . : 00-25-86-DF-C6-89 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.1.7(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 09 April 2010 23:09:45 Lease Expires . . . . . . . . . . : 10 April 2010 23:09:45 Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DNS Servers . . . . . . . . . . . : 192.168.1.1 NetBIOS over Tcpip. . . . . . . . : Enabled Ethernet adapter Local Area Connection 2: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller #2 Physical Address. . . . . . . . . : E0-CB-4E-26-B9-84 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : E0-CB-4E-26-BE-94 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Tunnel adapter isatap.{74D5C406-894E-4000-8DE7-6AAEBF7C8382}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft ISATAP Adapter #2 Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes Tunnel adapter Teredo Tunneling Pseudo-Interface: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv6 Address. . . . . . . . . . . : 2001:0:5ef5:73ba:881:20c1:3f57:fef8(Preferred) Link-local IPv6 Address . . . . . : fe80::881:20c1:3f57:fef8%14(Preferred) Default Gateway . . . . . . . . . : :: NetBIOS over Tcpip. . . . . . . . : Disabled

  Read the article

• Unable to install SQL 2008 on Windows 7

  - by Axel

  SQL 2008 install hangs on Windows 7 The story: Trying to install SQL2008 on Windows 7 hangs on SqlEngineDBStartconfigAction_install_configrc_Cpu32. What I Tried: Uninstall hangs on validation Manual uninstall using msiinv.exe and msiexec /x works Added SQL service accounts to local admins no help Turn of UAC no help Last lines in setup log: 2010-04-01 16:18:05 SQLEngine: : Checking Engine checkpoint 'GetSqlServerProcessHandle' 2010-04-01 16:18:05 SQLEngine: --SqlServerServiceSCM: Waiting for nt event 'Global\sqlserverRecComplete' to be created 2010-04-01 16:18:07 SQLEngine: --SqlServerServiceSCM: Waiting for nt event 'Global\sqlserverRecComplete' or sql process handle to be signaled 2010-04-01 16:18:07 SQLEngine: : Checking Engine checkpoint 'WaitSqlServerStartEvents' 2010-04-01 16:18:53 Slp: Sco: Attempting to initialize script 2010-04-01 16:18:53 Slp: Sco: Attempting to initialize default connection string 2010-04-01 16:18:53 Slp: Sco: Attempting to set script connection protocol to NotSpecified 2010-04-01 16:18:53 Slp: Sco: Attempting to set script connection protocol to NamedPipes 2010-04-01 16:18:53 SQLEngine: --SqlDatabaseServiceConfig: Connection String: Data Source=\.\pipe\SQLLocal\MSSQLSERVER;Initial Catalog=master;Integrated Security=True;Pooling=False;Network Library=dbnmpntw;Application Name=SqlSetup 2010-04-01 16:18:53 SQLEngine: : Checking Engine checkpoint 'ServiceConfigConnect' 2010-04-01 16:18:53 SQLEngine: --SqlDatabaseServiceConfig: Connecting to SQL.... 2010-04-01 16:18:53 Slp: Sco: Attempting to connect script 2010-04-01 16:18:53 Slp: Connection string: Data Source=\.\pipe\SQLLocal\MSSQLSERVER;Initial Catalog=master;Integrated Security=True;Pooling=False;Network Library=dbnmpntw;Application Name=SqlSetup And now comes the fun part: When I open conf mgr I can see the service running, I enabled named pipes and TCP/IP, restarted the service I'm able to connect to the server using an OLE DB connection but not with the Native Client. And what I find suspicious is the following error in my app log: .NET Runtime Optimization Service (clr_optimization_v2.0.50727_32) - Failed to compile: C:\Program Files\Microsoft SQL Server\100\Tools\Binn\VSShell\Common7\Tools\VDT\DataProjects.dll . Error code = 0x8007000b In MS connect this is reported as a bug but MS is unable to reproduce the problem altough when you search the fora I'm not the only one with this problem. So any help is appreciated.

  Read the article

• VSTS 2010 SGEN : error : Could not load file or assembly (Exception from HRESULT: 0x80131515)

  - by Developer IT

  Hi ! I am experiencing a strange issue with VS2010. We use TFS to build our API dlls and we used to reference them in our projects usign a mapped network drive that was fully trusted. We have been working like that for at least two years and everything worked perfectly. Today, I converted a webapp to vs2010 and when I compile it in Release, it's giving me: SGEN : error : Could not load file or assembly 'file:///L:\Api\Release API_20100521.1\Release\CS.API.Exceptions.dll' or one of its dependencies. Operation is not supported. (Exception from HRESULT: 0x80131515) The strange thing is that it's working when it's under the Debug profile... I tried adding the <runtime> <loadFromRemoteSources enabled="true" /> </runtime> into app.config and still no luck (See http://social.msdn.microsoft.com/Forums/en/msbuild/thread/d12f6301-85bf-4b9e-8e34-a06398a60df0 and http://msdn.microsoft.com/en-us/library/dd409252(VS.100).aspx) I am pretty sure that this issue is from visual studio or msbuild, as our code won't run from a network share when in prod because all the referenced dll's are copied into the bin folder. If anyone has an solution (or just an idea for a search path) please let me know !

  Read the article

• Path Not Found error when opening VB6 project from a shared folder on Virtual PC 2007 (XP sp3)

  - by law1185

  I currently work on a small software team that primarily maintains legacy software. I am trying to set up a VirtualPC that we can use to do this maintenance. Specifically, I would like to be able to debug and run VB6 web apps from a folder on the host pc. My constraints are as follows: The VirtualPC will not be registered on the domain. The server that hosts our Subversion repository does not run the subversion service so the only way to interact with the repository is through "file:\\", which requires domain authentication. It is not possible to debug/run VB6 web apps that are located on mapped network drives, because IIS requires that the VirtualPC be on the same domain as the network drive I would like to avoid having to copy the folder from the host pc to the VirtualPC and then copying it back in order to have the latest revision from Subversion So, I am trying to use VirtualPC's shared folder feature to share the host machine's Subversion directory and open the project in VB6 on the VirtualPC. Problem is that Visual Basic throws the error: "Path not found: '\\C:\\Subversion\Path\Project.vbp'" when I try to open it. Folder C:\Subversion on the host machine is mapped to G: on the VirtualPC. If anyone can help me resolve this error or find some other way to accomplish this, I would be deeply grateful. Oh, both host and virtual OS is Windows XP sp3. Using VB 6.0, IIS v5.1. I can manipulate files in the shared directory freely from the VirtualPC ie. copy, paste, delete, etc. Edit: Link to screenshot: http://img190.imageshack.us/img190/5439/vpcscreen.png

  Read the article

• Cisco ASA and SixXS IPv6 tunnel endpoint?

  - by Martijn Heemels

  I recently installed a Cisco ASA 5505 firewall on the edge of our LAN. The setup is simple: Internet <-- ASA <-- LAN I would like provide the hosts in the LAN with IPv6 connectivity by setting up a 6in4 tunnel to SixXS. It would be nice to have the ASA as tunnel endpoint so it can firewall both IPv4 and IPv6 traffic. Unfortunately the ASA apparently can't create a tunnel itself, and can't port-forward protocol 41 traffic, so I believe I would have to do one of the following instead: Set up a host with it's own IP outside the firewall, and have that function as tunnel-endpoint. The ASA can then firewall and route the v6 subnet to the LAN. Set up a host inside the firewall that functions as endpoint, separated via vlan or whatever, and loop the traffic back into the ASA where it can be firewalled and routed. This seems contrived, but would allow me to use a VM instead of a physical machine as endpoint. Any other way? What would you suggest is the optimal way to set this up? P.S. I do have a spare public IP address available if needed, and can spin up another VM in our VMware infrastructure.

  Read the article

• .NET remoting exception: Exception in the Socket#33711845::DoBind - Only one usage of each socket ad

  - by wollemi

  Hi All, I'm attempting to setup a simple remoting windows service and getting the following error when starting the service: "System.Net.Sockets Error: 0 : [4180] Exception in the Socket#33711845::DoBind - Only one usage of each socket address (protocol/network address/port) is normally permitted System.Net.Sockets Verbose: 0 : [4180] ExclusiveTcpListener#4032828::Start() System.Net.Sockets Verbose: 0 : [4180] Socket#33711845::Bind(0:9998#9998) System.Net.Sockets Error: 0 : [4180] Exception in the Socket#33711845::DoBind - Only one usage of each socket address (protocol/network address/port) is normally permitted ". In the windows service application I have the following code in the "OnStart" method - the error occurs when registering the Channel - ChannelServices.RegisterChannel(tcpPipe, true); As far as I can tell there are no other processes using port 9998 ... Your help to resolve this is most appreciated! protected override void OnStart(string[] args) { int portNumber = int.Parse(ConfigurationManager.AppSettings["endPointTCPPort"]); TcpChannel tcpPipe = new TcpChannel(portNumber); ChannelServices.RegisterChannel(tcpPipe, true); Type serviceType = Type.GetType("TractionGatewayService.TractionGateway"); try { RemotingConfiguration.RegisterWellKnownServiceType(serviceType, "updateCustomerDetails", WellKnownObjectMode.SingleCall); } catch (RemotingException e) { EventLog.WriteEntry("unable to establish listening port because " + e.message; ChannelServices.UnregisterChannel(tcpPipe); } w

  Read the article

• Can't join OS X Mavericks to AD Domain

  - by watkipet

  I'm attempting to join an OS X Mavericks (10.9) client to a Windows Server 2008 Active Directory domain, however the bind fails with this error in the OS X client's system.log: Oct 24 15:03:15 host.domain.com com.apple.preferences.users.remoteservice[5547]: -[ODCAddServerSheetController handleOtherActionError: gotError: Error Domain=com.apple.OpenDirectory Code=5202 "Authentication server encountered an error while attempting the requested operation." UserInfo=0x7f9e6cb3e180 {NSLocalizedDescription=Authentication server encountered an error while attempting the requested operation., NSLocalizedFailureReason=Authentication server encountered an error while attempting the requested operation.}, Authentication server encountered an error while attempting the requested operation. I've joined (bound) Ubuntu Linux clients to the same domain with net ads join in the past with no problems (using the same administrative user). I don't have access to any server logs. Here's the GUI error (from Directory Utility) on the OS X client: Here's the GUI error (from User's and Groups) in System Preferences on the OS X client: Update After some Wiresharking I've got some more info: OS X Client - KDC (over UDP): AS_REQ (no padata) OS X Client <- KDC (over UDP): KRB5KDC_ERR_PREAUTH_REQUIRED OS X Client - KDC (over UDP): AS_REQ (this time with PA-ENC-TIMESTAMP in padata) OS X Client <- KDC (over UDP): KRB5KDC_ERR_RESPONSE_TOO_BIG OS X Client - KDC (over TCP): AS_REQ (also with PA-ENC-TIMESTAMP in padata) OS X Client <- KDC (over TCP): KDC_ERR_ETYPE_NOSUPP ...and that's it. This is what I think is going on: The OS X client sends a kerberos request. The KDC says, "You need to pre-authenticate. Try again" The OS X client tries to pre-authenticate (all this so far is over UDP) Something gets lost on our network and the KDC says, "Oops something went wrong" The OS X client switches to TCP and tries again. Over TCP, the KDC says, "You're using an encryption type I don't support" Note that in its padata records, the OS X client is always using "aes256-cts-hmac-sha1-96" as its encryption type. However, in its KDC_REQ_BODY record it lists the aes256-cts-hmac-sha1-96, aes128-cts-hmac-sha1-96, des3-cbc-sha1, and rc4-hmac encryption types. When the KDC comes back with KDC_ERR_ETYPE_NOSUPP, it uses rc4-hmac as its encryption type in its padata record. I know next to nothing about Kerberos, but it seems to me that the OS X client should go ahead and try the rc4-hmac encryption type. However, it does nothing after this. Update 2 Here's the debug log from Directory Services on the OS X client. Sorry--it's long. 2013-10-25 14:19:13.219128 PDT - 10544.20463 - ODNodeCustomCall request, NodeID: 52A65FAE-4B24-455D-86EC-2199A780D234, Code: 80 2013-10-25 14:19:13.220409 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - client requested OU - 'CN=Computers,DC=domain,DC=com' 2013-10-25 14:19:13.220427 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - Binding using '[email protected]' for kerberos ID 2013-10-25 14:19:13.220571 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - new kerberos credential cache 'MEMORY:0x7fa713635470' for '[email protected]' 2013-10-25 14:19:13.220623 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - krb5_get_init_creds: loop 1 2013-10-25 14:19:13.220639 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - KDC send 0 patypes 2013-10-25 14:19:13.220653 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - fast disabled, not doing any fast wrapping 2013-10-25 14:19:13.220699 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - Trying to find service kdc for realm DOMAIN.COM flags 0 2013-10-25 14:19:13.221275 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - submissing new requests to new host 2013-10-25 14:19:13.221326 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - connecting to host: udp 192.168.0.1:kerberos (192.168.0.1) tid: 00000001 2013-10-25 14:19:13.221373 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - writing packet: udp 192.168.0.1:kerberos (192.168.0.1) tid: 00000001 2013-10-25 14:19:13.222588 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - reading packet: udp 192.168.0.1:kerberos (192.168.0.1) tid: 00000001 2013-10-25 14:19:13.222617 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - host completed: udp 192.168.0.1:kerberos (192.168.0.1) tid: 00000001 2013-10-25 14:19:13.222665 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - krb5_sendto_context DOMAIN.COM done: 0 hosts 1 packets 1 wc: 0.001960 nr: 0.000000 kh: 0.000560 tid: 00000001 2013-10-25 14:19:13.222705 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - krb5_get_init_creds: loop 2 2013-10-25 14:19:13.222737 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - krb5_get_init_creds: processing input 2013-10-25 14:19:13.222752 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - krb5_get_init_creds: got an KRB-ERROR from KDC 2013-10-25 14:19:13.222775 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - krb5_get_init_creds: KRB-ERROR -1765328359/Additional pre-authentication required 2013-10-25 14:19:13.222791 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - KDC send 4 patypes 2013-10-25 14:19:13.222800 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - KDC send PA-DATA type: 19 2013-10-25 14:19:13.222808 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - KDC send PA-DATA type: 2 2013-10-25 14:19:13.222816 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - KDC send PA-DATA type: 16 2013-10-25 14:19:13.222825 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - KDC send PA-DATA type: 15 2013-10-25 14:19:13.222840 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - krb5_get_init_creds: using ENC-TS with enctype 18 2013-10-25 14:19:13.222850 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - krb5_get_init_creds: using default_s2k_func 2013-10-25 14:19:13.227443 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - fast disabled, not doing any fast wrapping 2013-10-25 14:19:13.227502 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - Trying to find service kdc for realm DOMAIN.COM flags 0 2013-10-25 14:19:13.228233 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - submissing new requests to new host 2013-10-25 14:19:13.228320 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - connecting to host: udp 192.168.0.1:kerberos (192.168.0.1) tid: 00010001 2013-10-25 14:19:13.228374 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - writing packet: udp 192.168.0.1:kerberos (192.168.0.1) tid: 00010001 2013-10-25 14:19:13.229930 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - reading packet: udp 192.168.0.1:kerberos (192.168.0.1) tid: 00010001 2013-10-25 14:19:13.229957 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - host completed: udp 192.168.0.1:kerberos (192.168.0.1) tid: 00010001 2013-10-25 14:19:13.229975 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - krb5_sendto trying over again (reset): 0 2013-10-25 14:19:13.230023 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - Trying to find service kdc for realm DOMAIN.COM flags 2 2013-10-25 14:19:13.230664 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - submissing new requests to new host 2013-10-25 14:19:13.230726 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - connecting to host: tcp 192.168.0.1:kerberos (192.168.0.1) tid: 00010002 2013-10-25 14:19:13.230818 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - connecting to 11: tcp 192.168.0.1:kerberos (192.168.0.1) tid: 00010002 2013-10-25 14:19:13.231101 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - writing packet: tcp 192.168.0.1:kerberos (192.168.0.1) tid: 00010002 2013-10-25 14:19:13.232743 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - reading packet: tcp 192.168.0.1:kerberos (192.168.0.1) tid: 00010002 2013-10-25 14:19:13.232777 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - host completed: tcp 192.168.0.1:kerberos (192.168.0.1) tid: 00010002 2013-10-25 14:19:13.232798 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - krb5_sendto_context DOMAIN.COM done: 0 hosts 2 packets 2 wc: 0.005316 nr: 0.000000 kh: 0.001339 tid: 00010002 2013-10-25 14:19:13.232856 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - krb5_get_init_creds: loop 3 2013-10-25 14:19:13.232868 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - krb5_get_init_creds: processing input 2013-10-25 14:19:13.232900 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - krb5_get_init_creds: using keyproc 2013-10-25 14:19:13.232910 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - krb5_get_init_creds: using default_s2k_func 2013-10-25 14:19:13.236487 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - krb5_get_init_creds: extracting ticket 2013-10-25 14:19:13.236557 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - krb5_get_init_creds: wc: 0.015944 2013-10-25 14:19:13.237022 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - Trying to find service kdc for realm DOMAIN.COM flags 2 2013-10-25 14:19:13.237444 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - submissing new requests to new host 2013-10-25 14:19:13.237482 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - connecting to host: tcp 192.168.0.1:kerberos (192.168.0.1) tid: 00020001 2013-10-25 14:19:13.237551 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - connecting to 11: tcp 192.168.0.1:kerberos (192.168.0.1) tid: 00020001 2013-10-25 14:19:13.237900 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - writing packet: tcp 192.168.0.1:kerberos (192.168.0.1) tid: 00020001 2013-10-25 14:19:13.238616 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - reading packet: tcp 192.168.0.1:kerberos (192.168.0.1) tid: 00020001 2013-10-25 14:19:13.238645 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - host completed: tcp 192.168.0.1:kerberos (192.168.0.1) tid: 00020001 2013-10-25 14:19:13.238674 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - krb5_sendto_context DOMAIN.COM done: 0 hosts 1 packets 1 wc: 0.001656 nr: 0.000000 kh: 0.000409 tid: 00020001 2013-10-25 14:19:13.238839 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - Trying to find service kdc for realm DOMAIN.COM flags 2 2013-10-25 14:19:13.239302 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - submissing new requests to new host 2013-10-25 14:19:13.239360 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - connecting to host: tcp 192.168.0.1:kerberos (192.168.0.1) tid: 00030001 2013-10-25 14:19:13.239429 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - connecting to 11: tcp 192.168.0.1:kerberos (192.168.0.1) tid: 00030001 2013-10-25 14:19:13.239683 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - writing packet: tcp 192.168.0.1:kerberos (192.168.0.1) tid: 00030001 2013-10-25 14:19:13.240350 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - reading packet: tcp 192.168.0.1:kerberos (192.168.0.1) tid: 00030001 2013-10-25 14:19:13.240387 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - host completed: tcp 192.168.0.1:kerberos (192.168.0.1) tid: 00030001 2013-10-25 14:19:13.240415 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - krb5_sendto_context DOMAIN.COM done: 0 hosts 1 packets 1 wc: 0.001578 nr: 0.000000 kh: 0.000445 tid: 00030001 2013-10-25 14:19:13.240514 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - krb5_credential - krb5_get_credentials_with_flags: DOMAIN.COM wc: 0.003615 2013-10-25 14:19:13.240537 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - valid credentials for [email protected] 2013-10-25 14:19:13.240541 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - switching to cache 'MEMORY:0x7fa713635470' 2013-10-25 14:19:13.240545 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - switching GSS to cache 'MEMORY:0x7fa713635470 2013-10-25 14:19:13.240555 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - Bind Step 5 - Bind/Join computer to domain - 'domain.com' 2013-10-25 14:19:13.241345 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - resolving 'server.domain.com' 2013-10-25 14:19:13.241646 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - added socket 12 for host 'server.domain.com:389' address '192.168.0.2' to kqueue list 2013-10-25 14:19:13.241930 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - Setting kerberos server for 'Kerberos:DOMAIN.COM' to 'server.domain.com' 2013-10-25 14:19:13.241962 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - switching to cache 'MEMORY:0x7fa713635470' 2013-10-25 14:19:13.241969 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - switching GSS to cache 'MEMORY:0x7fa713635470 2013-10-25 14:19:13.242231 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - GSSAPI allow Confidentiality 2013-10-25 14:19:13.242234 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - setting realm 'DOMAIN.COM' for node '/Active Directory/domain.com' 2013-10-25 14:19:13.242239 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - GSSAPI allow Integrity (signing) 2013-10-25 14:19:13.242274 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - GSSAPI using hostname 'server.domain.com' 2013-10-25 14:19:13.242282 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - GSSAPI using initiator credential '[email protected]' 2013-10-25 14:19:13.250771 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - Authenticate to LDAP using Kerberos credential - 0 2013-10-25 14:19:13.250784 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - verified connectivity to '192.168.0.2' with socket 12 2013-10-25 14:19:13.251513 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - locating site using domain domain.com using CLDAP 2013-10-25 14:19:13.252145 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - using site of 'DOMAINGROUP' from CLDAP 2013-10-25 14:19:13.253626 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - resolving 'server2.domain.com' 2013-10-25 14:19:13.253933 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - added socket 13 for host 'server2.domain.com:389' address '192.168.0.1' to kqueue list 2013-10-25 14:19:13.254428 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - Setting kerberos server for 'Kerberos:DOMAIN.COM' to 'server2.domain.com' 2013-10-25 14:19:13.254462 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - switching to cache 'MEMORY:0x7fa713635470' 2013-10-25 14:19:13.254468 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - switching GSS to cache 'MEMORY:0x7fa713635470 2013-10-25 14:19:13.254617 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - setting realm 'DOMAIN.COM' for node '/Active Directory/domain.com' 2013-10-25 14:19:13.254661 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - GSSAPI allow Confidentiality 2013-10-25 14:19:13.254670 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - GSSAPI allow Integrity (signing) 2013-10-25 14:19:13.254689 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - GSSAPI using hostname 'server2.domain.com' 2013-10-25 14:19:13.254695 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - GSSAPI using initiator credential '[email protected]' 2013-10-25 14:19:13.262092 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - Authenticate to LDAP using Kerberos credential - 0 2013-10-25 14:19:13.262108 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - verified connectivity to '192.168.0.1' with socket 13 2013-10-25 14:19:13.262982 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - Computer account either already exists or DC is already Read/Write 2013-10-25 14:19:13.264968 PDT - 10544.20463, Node: /Active Directory, Module: ActiveDirectory - Adding record 'cn=spike,CN=Computers,DC=domain,DC=com' in 'domain.com' The failure point seems to be Computer account either already exists or DC is already Read/Write, however, I can search for 'spike' on the Active Directory server using Active Directory Explorer and it's not there. If I do the same search for the Linux and Windows PCs I added previously, I can find them.

  Read the article

• Sending email through proxy using gmail smtp

  - by baron

  Hello everyone, Trying to send some email in my C# app. I am behind a proxy - which is no doubt why the code isn't working. This is what I have so far: App.Config: <system.net> <defaultProxy enabled="false"> <proxy proxyaddress="xxx.xxx.xxx.xxx"/> </defaultProxy> <mailSettings> <smtp deliveryMethod="Network"> <network host="smtp.gmail.com" port="587"/> </smtp> </mailSettings> </system.net> Code: var username = "..."; var password = "..."; var fromEmail = "..."; var toEmail = "..."; var body = "Test email body"; var subject = "Test Subject Email"; var client = new SmtpClient("smtp.gmail.com", 587) { Credentials = new NetworkCredential(username, password), EnableSsl = true }; try { client.Send(fromEmail, toEmail, subject, body); } catch (Exception e) { MessageBox.Show(e.Message); } Everytime I get System.Net.WebException: The remote name could not be resolved: 'smtp.gmail.com' Where/how do I start to debug?

  Read the article

• RSACryptoServiceProvider CryptographicException System Cannot Find the File Specified under ASP.NET

  - by Will Hughes

  I have an application which is making use of the RSACryptoServiceProvider to decrypt some data using a known private key (stored in a variable). When the IIS Application Pool is configured to use Network Service, everything runs fine. However, when we configure the IIS Application Pool to run the code under a different Identity, we get the following: System.Security.Cryptography.CryptographicException: The system cannot find the file specified. at System.Security.Cryptography.Utils.CreateProvHandle(CspParameters parameters, Boolean randomKeyContainer) at System.Security.Cryptography.RSACryptoServiceProvider.ImportParameters(RSAParameters parameters) at System.Security.Cryptography.RSA.FromXmlString(String xmlString) The code is something like this: byte[] input; byte[] output; string private_key_xml; var provider = new System.Cryptography.RSACryptoServiceProvider(this.m_key.Key_Size); provider.FromXmlString(private_key_xml); // Fails Here when Application Pool Identity != Network Service ouput = provider.Decrypt(input, false); // False = Use PKCS#1 v1.5 Padding There are resources which attempt to answer it by stating that you should give the user read access to the machine key store - however there is no definitive answer to solve this issue. Environment: IIS 6.0, Windows Server 2003 R2, .NET 3.5 SP1

  Read the article

• Calculating File size before download - Downloading NSURLConnection Slider timing

  - by sagar

  Ok ! Coming to the point directly. What I want to do is explained as follows. I have an url of MP3 file. ( for example Sound File ) Now, When user starts application. Download should start & for that I have implemented following methods. -(void)viewDidLoad { [super viewDidLoad]; NSURL *url=[NSURL URLWithString:@"http://xyz.pqr.com/abc.mp3"]; NSURLRequest *req=[NSURLRequest requestWithURL:url cachePolicy:NSURLCacheStorageNotAllowed timeoutInterval:120]; NSURLConnection *con=[[NSURLConnection alloc] initWithRequest:req delegate:self startImmediately:YES]; if(con){ myWebData=[[NSMutableData data] retain]; } else { // [MainHandler performSelector:@selector(targetSelector:) withObject:nil]; } } -(void)connection:(NSURLConnection *)connection didReceiveResponse:(NSURLResponse *)response { NSLog(@"%@",@"connection established"); [myWebData setLength: 0]; } -(void)connection:(NSURLConnection *)connection didReceiveData:(NSData *)data { NSLog(@"%@",@"connection receiving data"); [myWebData appendData:data]; } -(void)connection:(NSURLConnection *)connection didFailWithError:(NSError *)error { NSLog(@"%@",@"connection failed"); [connection release]; // [AlertViewHandler showAlertWithErrorMessage:@"Sorry, there is no network connection. Please check your network and try again."]; // [self parserDidEndDocument:nil]; } -(void)connectionDidFinishLoading:(NSURLConnection *)connection { [connection release]; } Now, Above methods work perfectly for downloading. But missing points are as follows. I can not get the exact size which is going to be downloaded. ( means I want to know what is the size of file - which is going to be download )

  Read the article

• "cloud architecture" concepts in a system architecture diagrams

  - by markus

  If you design a distributed application for easy scale-out, or you just want to make use of any of the new “cloud computing” offerings by Amazon, Google or Microsoft, there are some typical concepts or components you usually end up using: distributed blob storage (aka S3) asynchronous, durable message queues (aka SQS) non-Relational-/non-transactional databases (like SimpleDB, Google BigTable, Azure SQL Services) distributed background worker pool load-balanced, edge-service processes handling user requests (often virtualized) distributed caches (like memcached) CDN (content delivery network like Akamai) Now when it comes to design and sketch an architecture that makes use of such patterns, are there any commonly used symbols I could use? Or even a download with some cool Visio stencils? :) It doesn’t have to be a formal system like UML but I think it would be great if there were symbols that everyone knows and understands, like we have commonly used shapes for databases or a documents, for example. I think it would be important to not mix it up with traditional concepts like a normal file system (local or network server/SAN), or a relational database. Simply speaking, I want to be able to draw some conclusions about an application’s scalability or data consistency issues by just looking at the system architecture overview diagram. Update: Thank you very much for your answers. I like the idea of putting a small "cloud symbol" on the traditional symbols. However I leave this thread open just in case someone will find specific symbols (maybe in a book or so) - or uploaded some pimped up Visio stencils ;)

  Read the article

• VMRC equivalent for Hyper-V?

  - by Ian Boyd

  VMRC was the client tool used to connect to virtual machines running on Virtual Server. Upgrading to Windows Server 2008 R2 with the Hyper-V role, i need a way for people to be able to use the virtual machines. Note: not all virtual machines will have network connectivity not all virtual machines will be running Windows some people needing to connect to a virtual machine will be running Windows XP Hyper-V manager, allowing management of the hyper-v server, is less desirable (since it allows management of the hyper-v server (and doesn't work on all operating systems)) What is the Windows Server 2008 R2 equivalent of VMRC; to "vnc" to a virtual server? Update: i think Tatas was suggesting Microsoft System Center Virtual Machine Manager Self-Service Portal 2.0 (?): Which requires SQL Server IIS Installing those would unfortunately violate our Windows Server 2008 R2 license. i might be looking at the wrong product link, since commenter said there is a version that doesn't require "System Center". Update 2: The Windows Server 2008 R2 running HyperV is being licensed with the understanding that it only be used to host HyperV. From the [Windows Server 2008 R2 Licensing FAQ][4]: Q. If I have one license for Windows Server 2008 R2 Standard and want to run it in a virtual operating system environment, can I continue running it in the physical operating system environment? A. Yes, with Windows Server 2008 R2 Standard, you may run one instance in the physical operating system environment and one instance in the virtual operating system environment; however, the instance running in the physical operating system environment may be used only to run hardware virtualization software, provide hardware virtualization services, or to run software to manage and service operating system environments on the licensed server. This is why i'm weary about installing IIS or SQL Server.

  Read the article

• Can't get my OpenVpn client to connect

  - by Larry

  Hi Guys, I am trying to setup a test vpn between my home desktop and my laptop. So far I have got the server on the desktop to connect fine but I can not get my laptop to finish the connection. I have tried several different configurations and they all give me the same result. Obviously it has nothing to do with my Client configuration but possibly something on my laptop? Here is the message I get in the log when it stops then times out and restarts. Mon Oct 18 20:10:55 2010 UDPv4 link local: [undef] Mon Oct 18 20:10:55 2010 UDPv4 link remote: 74.190.29.236:1194 Mon Oct 18 20:11:55 2010 TLS Error: TLS key negotiation failed to occur within 60 seconds (check your network connectivity) Mon Oct 18 20:11:55 2010 TLS Error: TLS handshake failed here are my configurations server.ovpn port 1194 proto udp dev tun ca ca.crt cert server.crt key server.key dh dh1024.pem server 10.8.0.1 255.255.255.252 ifconfig-pool-persist ipp.txt push "route 10.0.0.1 255.255.255.0" push "dhcp-option WINS 10.0.0.5" push "dhcp-option DNS 10.0.0.5" push "dhcp-option DOMAIN acme.com.local" keepalive 10 120 comp-lzo max-clients 1 persist-key persist-tun status openvpn-status.log verb 3 LArry.ovpn client proto udp dev tun remote doublel.hopto.org 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client1.crt key client1.key comp-lzo verb 3 dev tun local 206.162.148.9 remote 134.28.54.2 ifconfig 192.168.99.1 192.168.99.2 route 10.0.0.0 255.0.0.0 192.168.99.2 I just need a simple vpn for one user. Am I headed down the right path? Thanks, Larry

  Read the article

• Zscaler. Certs, cookies, and port 80 traffic

  - by 54's_lol

  So I work at HQ for a large company that shall remain nameless. We use Zscaler and I had to roll out a 2048 cert per zscaler's request. People around me at work dont understand the technology and think that the cert's are what is allowing internet connectivity. From my understanding(and please chime in) is the cookie located C:\Users\$$$$$$4$$\AppData\Roaming\Macromedia\Flash Player#SharedObjects\Q3JQJQJV\gateway.zscaler.net\zscaler.swf here that gets created when you provide your creds the first time you use the browser. The cert's are just simply a way of inspecting the SSL traffic as zscaler had no way of doing this before without them. They are essentially using the classic MITM attack to parse your SSL traffic. Gmail is smart enough to recognize this as you get a warning. My question is this, is there a product or service that I can use to verify my web browser when at home(I.E. off company network) isn't still getting routed to zscaler's cloud? If i do a tracert that will work fine. It's the port 80 and 443 web traffic zscaler and my company is after. I would like to verify that when I'm off their premise that my web traffic is using only my isp and the path to whatever content I'm searching for. Do the cert's i'm pushing and browser authentication do something behind the curtain that forces web traffic to get routed to zscaler? I searched quite a bit and would very much like to know if I'm ever off company scrutiny. I do know zscaler offers the service to force the scenario im asking about. Can I prove how my web traffic is getting routed? Thanks for any insight. I've been a fan for a long time and your guy's kung fu is very strong:-)

  Read the article

• How to handle corrupt messages arriving on a socket?

  - by Pieter

  I've got a working socket handling mechanism, similar (but a bit more complex) to Qt's Fortune Example http://qt.nokia.com/doc/4.5/network-fortuneclient.html http://qt.nokia.com/doc/4.5/network-fortuneserver.html Now I'm wondering how to handle corrupt messages. Discarding the data is a start, but I need to discard up to a point I can start processing messages again. The corrupt message may be lost, but I need to be able to recover from it. I've got the following idea in mind: Put a fixed header at the start of each message, eg. 0xABCDEF01. When recovering, lookup this header and restart handling incoming messages. = Break off readFortune() on a timeout and recover = When encountering an inconsistent header, recover A huge blocksize is still going to be a problem. To fix that, I should be constantly checking whether or not I'm reading gibberish, but this is not always possible. I can also limit the blocksize on certain message-types. Any ideas on this? Any proposals on what to use as byteword?

  Read the article

• Combinations into pairs

  - by Will

  I'm working on a directed network problem and trying to compute all valid paths between two points. I need a way to look at paths up to 30 "trips" (represented by an [origin, destination] pair) in length. The full route is then composed of a series of these pairs: route = [[start, city2], [city2, city3], [city3, city4], [city4, city5], [city5, city6], [city6, city7], [city7, city8], [city8, stop]] So far my best solution is as follows: def numRoutes(graph, start, stop, minStops, maxStops): routes = [] route = [[start, stop]] if distance(graph, route) != "NO SUCH ROUTE" and len(route) >= minStops and len(route) <= maxStops: routes.append(route) if maxStops >= 2: for city2 in routesFromCity(graph, start): route = [[start, city2],[city2, stop]] if distance(graph, route) != "NO SUCH ROUTE" and len(route) >= minStops and len(route) <= maxStops: routes.append(route) if maxStops >= 3: for city2 in routesFromCity(graph, start): for city3 in routesFromCity(graph, city2): route = [[start, city2], [city2, city3], [city3, stop]] if distance(graph, route) != "NO SUCH ROUTE" and len(route) >= minStops and len(route) <= maxStops: routes.append(route) if maxStops >= 4: for city2 in routesFromCity(graph, start): for city3 in routesFromCity(graph, city2): for city4 in routesFromCity(graph, city3): route = [[start, city2], [city2, city3], [city3, city4], [city4, stop]] if distance(graph, route) != "NO SUCH ROUTE" and len(route) >= minStops and len(route) <= maxStops: routes.append(route) if maxStops >= 5: for city2 in routesFromCity(graph, start): for city3 in routesFromCity(graph, city2): for city4 in routesFromCity(graph, city3): for city5 in routesFromCity(graph, city4): route = [[start, city2], [city2, city3], [city3, city4], [city4, city5], [city5, stop]] if distance(graph, route) != "NO SUCH ROUTE" and len(route) >= minStops and len(route) <= maxStops: routes.append(route) return routes Where numRoutes is fed my network graph where numbers represent distances: [[0, 5, 0, 5, 7], [0, 0, 4, 0, 0], [0, 0, 0, 8, 2], [0, 0, 8, 0, 6], [0, 3, 0, 0, 0]] a start city, an end city and the parameters for the length of the routes. distance checks if a route is viable and routesFromCity returns the attached nodes to each fed in city. I have a feeling there's a far more efficient way to generate all of the routes especially as I move toward many more steps, but I can't seem to get anything else to work.

  Read the article

• Site to Site VPN with Fault Tolerence

  - by Nordberg

  Hello, I have a situation where I require an IPSEC tunnel between two sites. Site 2 is a small branch office with basic (ADSL) connectivity and Site 1 is the "main" office with SDSL and ADSL for redundancy should the SDSL fail. From Site 1, all traffic bound for the 172.0.0.0 network will then be sent down another IPSEC tunnel to a supplier's Remote Server. See this page for the basic premise (this is a rough idea and things can be moved about etc...) I am considering specifying Cisco ASA devices as the firewalls for both sites for all connections. Would it be possible to employ something like HSRC to provide a backup at Site 1 should the SDSL go down? I suppose the key aims here are that Site 2 can somehow failover to initiate a VPN to the ASA behind the ADSL at Site 1. I will have a 21 subnet mask on all internet connections so can play with Class C routing if need be... If I'm barking up the wrong tree with HSRC, is there another way I can acheive this without massive expenditure on Barracuda routers et al? Many Thanks.

  Read the article

• IIS 7 can't connect to SQLServer 2008

  - by Nicolas Cadilhac

  Sorry if this is the most seen question on the web, but this is my turn. I am trying to publish my asp.net mvc app on IIS 7 under MS Sql Server 2008. I am on a Windows Server 2008 virtual machine. I get the following classical error: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) Under SQLServer, Allow remote connections is checked. My connection string is: Data Source=.\MSSQLSERVER;Initial Catalog=mydbname;User Id=sa;Password=mypassword I also tried with no username/password and "Integrated Security=true". There is only one instance of SQLServer installed. I tried to access my web page locally and remotely. There is no active firewall on the virtual machine. Thx for your help.

  Read the article

• rr.com appended to URL and I don't know why

  - by Steph

  I've been having some pretty bad and intermittent internet connectivity issues. I keep getting timeouts on my browsers, or what appears to be timeouts on my browsers. In Chrome it's generally error 21. FF it times out. And so on. While this is happening, I can go into the command line and ping or traceroute the same domain and it works fine. I use my cellphone on the same network and it's fine connecting to the same domain. And when it fails, it's all domains that are down in all browsers, chrome, FF, etc. I also noticed that when I try to connect to 192.168.1.1 it says in chrome did you mean www.192.168.1.1rr.com but when I enter https://192.168.1.1 it's fine. It only seems to do this in Chrome. This is making me think I have a virus. I did some researching about something called road runner, but I can't find any related traces. I also ran a full virus scan using nod32 (eset) and nothing. Any suggestion or help would be greatly appreciated. The intermittent loss of total internet access is really annoying and I'm worried about why it's trying to append the rr.com domain in Chrome. I suspect I'm dealing with two different issues, but you never know. Also for the DNS I'm using Google's DNS servers, the famous 8.8.8.8 and 8.8.8.4

  Read the article

• Web server with static IP from cable provider

  - by Dmitri

  I have a subscription to 5 static IP addresses. I want to run a web server from behind a router. My network config is as follows: Server's local address is 10.1.10.2, has IIS running on it, port 80 and 443 (IIS is not my fault, had to be done) the server's ip address is static, the subnet mask is 255.255.255.0, gateway is 10.1.10.1, which is the local address of the cable modem / router / gateway thingy. All looks to be in textbook order as far as the LAN goes. I can get to anything on my LAN from any computer on my LAN, whether they have static IP or get it through DHCP from the cable modem/router thingy. however, I have no internet access form any of my LAN computers. I called Comcast tech support and they say they can connect to my modem/router just fine and can actually use it to ping any computer on the internet or any computer on my LAN from the router/modem (i checked, myself, this is in fact the case). However, nothing on my LAN has internet connectivity. I tried pinging the DNS servers, nothing. I tried directly typing in web sites' IP addresses, nothing, so doesn't seem to be a DNS issue. Any Ideas? What malfunction of a router could be causing such weird behavior? nay ideas or educated guesses are very much appreciated.

  Read the article

• Text mining on large database (data mining)

  - by yox

  Hello, I have a large database of resumes (CV), and a certain table skills grouping all users skills. inside that table there's a field skill_text that describes the skill in full text. I'm looking for an algorithm/software/method to extract significant terms/phrases from that table in order to build a new table with standarized skills.. Here are some examples skills extracted from the DB : Sectoral and competitive analysis Business Development (incl. in international settings) Specific structure and road design software - Microstation, Macao, AutoCAD (basic knowledge) Creative work (Photoshop, In-Design, Illustrator) checking and reporting back on campaign progress organising and attending events and exhibitions Development : Aptana Studio, PHP, HTML, CSS, JavaScript, SQL, AJAX Discipline: One to one marketing, E-marketing (SEO & SEA, display, emailing, affiliate program) Mix marketing, Viral Marketing, Social network marketing. The output shoud be something like : Sectoral and competitive analysis Business Development Specific structure and road design software - Macao AutoCAD Photoshop In-Design Illustrator organising events Development Aptana Studio PHP HTML CSS JavaScript SQL AJAX Mix marketing Viral Marketing Social network marketing emailing SEO One to one marketing As you see only skills remains no other representation text. I know this is possible using text mining technics but how to do it ? the database is realy large.. it's a good thing because we can calculate text frequency and decide if it's a real skill or just meaningless text... The big problem is .. how to determin that "blablabla" is a skill ? thanks

  Read the article

< Previous Page | 397 398 399 400 401 402 403 404 405 406 407 408  | Next Page >