Search Results

Search found 11785 results on 472 pages for 'password protection'.

Page 401/472 | < Previous Page | 397 398 399 400 401 402 403 404 405 406 407 408  | Next Page >

• How to set up multiple SSIDs with bandwidth limiting on a single wireless router?

  - by Rahul Narain

  I have an Asus WL-520GU wireless router connected to a cable modem that I use for wireless internet access in my apartment. I would like to set it up so that it provides two SSIDs: one secured and password-protected for my regular use, and a "guest" SSID that's unsecured but throttled to, say, 10% of the available bandwidth. What is the most straightforward way to do this? I've been looking into DD-WRT and Tomato, both of which support my router. DD-WRT supports setting up multiple SSIDs using the GUI, but I don't know if it's possible to limit the bandwidth of each SSID independently; point #12 in this FAQ thread says it's not possible to limit by day or by MAC address, which is discouraging but not conclusive. Tomato allows bandwidth limits in its QoS settings, going by the screenshot here, but multiple SSID support is still experimental and it doesn't look like it will work with the encryption settings or bandwidth limits in the GUI. I'd like to know a good way to do this which gives me the fewest opportunities for screwing up. I'm no stranger to the command line, if that turns out to be what's necessary, but if so, please explain what the commands are doing because I don't have a good mental model of what needs to happen to set this up.

  Read the article

• Migrate openldap users and groups

  - by user53864

  I have an OpenLDAP server running on one of my ubuntu 8.10 servers. I used command-line only for OpenLdap installation and some basic configurations, everything else I'll configure with the Webmin gui tool. I'm trying to migrate to ubuntu 10.04 and I was able to migrate all other servies, application and databases but not the ldap. I'm an ldap beginner: I have installed OpenLDAP server and client on ubuntu 10.04 server using the link and used the following command to export and import ldap users and groups To export from 8.10 server slapcat > ldap.ldif To import to 10.04 server Stop ldap and slapadd -l ldap.ldif and Start ldap Then I accessed Webmin and checked in Ldap users and groups and I could see all the users and groups of my old ldap server.Whenever I create an ldap user from the webmin(in 8.10 or 10.04) a unix user is also created with the home directory under /home. But the imported users in 10.04 from 8.10 are not present as a unix user(/etc/passwd). How could I make the ldap users available as a unix user, is there any perfect way to export and import?. I also wanted to check the ldap users from the terminal that if password is exported properly but I don't know how to access the ldap users which are not available as unix users. On 8.10, I just use su - ldapuser and it is not working in the 10.04 as unix users are not created for the exported ldap users. If every thing works fine then the CVS works as it is using ldap authentication. Anybody could help me?

  Read the article

• problems installing mysql and phpmyadmin to localhost

  - by Joel

  Hi guys, I know there have been many similar questions, but as far as I can tell, most of the other people have gotten further than I have... I'm trying to get a WAMP setup happening. I've got PHP and Apache running and talking to each other. PHP is in c:\PHP Apache is in it's default program files folder. mySQL is in it's default install location. I have localhost setup at D:\public_html\ I'm able to navigate to localhost and see html and php files. But I have a simple mySQL test file: <?php // hostname or ip of server (for local testing, localhost should work) $dbServer='localhost'; // username and password to log onto db server $dbUser='root'; $dbPass=''; // name of database $dbName='test'; $link = mysql_connect("$dbServer", "$dbUser", "$dbPass") or die("Could not connect"); print "Connected successfully<br>"; mysql_select_db("$dbName") or die("Could not select database"); print "Database selected successfully<br>"; // close connection mysql_close($link); ?> When I try and open this, I get "could not connect" Now, I haven't even created a database yet, because I can't log into mySQL with phpmyadmin-so I think I've done something wrong in my mySQL install because they aren't talking to each other. I guess my main question is how do I first create a database in mySQL to be sure I have even installed it correctly?

  Read the article

• Blocking an IP in Webmin

  - by Dan J

  I've been checking my /var/log/secure log recently and have seen the same bot trying to brute force onto my Centos server running webmin. I created a chain + rule in Networking - Linux Firewall: Drop If source is 113.106.88.146 But I'm still seeing the attempted logins in the log: Jun 6 10:52:18 CentOS5 sshd[9711]: pam_unix(sshd:auth): check pass; user unknown Jun 6 10:52:18 CentOS5 sshd[9711]: pam_succeed_if(sshd:auth): error retrieving information about user larry Jun 6 10:52:19 CentOS5 sshd[9711]: Failed password for invalid user larry from 113.106.88.146 port 49328 ssh2 Here is the contents of /etc/sysconfig/iptables: # Generated by webmin *filter :banned-ips - [0:0] -A INPUT -p udp -m udp --dport ftp-data -j ACCEPT -A INPUT -p udp -m udp --dport ftp -j ACCEPT -A INPUT -p udp -m udp --dport domain -j ACCEPT -A INPUT -p tcp -m tcp --dport 20000 -j ACCEPT -A INPUT -p tcp -m tcp --dport 10000 -j ACCEPT -A INPUT -p tcp -m tcp --dport https -j ACCEPT -A INPUT -p tcp -m tcp --dport http -j ACCEPT -A INPUT -p tcp -m tcp --dport imaps -j ACCEPT -A INPUT -p tcp -m tcp --dport imap -j ACCEPT -A INPUT -p tcp -m tcp --dport pop3s -j ACCEPT -A INPUT -p tcp -m tcp --dport pop3 -j ACCEPT -A INPUT -p tcp -m tcp --dport ftp-data -j ACCEPT -A INPUT -p tcp -m tcp --dport ftp -j ACCEPT -A INPUT -p tcp -m tcp --dport domain -j ACCEPT -A INPUT -p tcp -m tcp --dport smtp -j ACCEPT -A INPUT -p tcp -m tcp --dport ssh -j ACCEPT -A banned-ips -s 113.106.88.146 -j DROP COMMIT # Completed # Generated by webmin *mangle :FORWARD ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :PREROUTING ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] COMMIT # Completed # Generated by webmin *nat :OUTPUT ACCEPT [0:0] :PREROUTING ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] COMMIT # Completed

  Read the article

• Windows 8 Pro Homegroup Not Allowing Access to Shared Files

  - by Jack Herr

  I have two pc's and a laptop. With all three running Windows 7, homegroup worked perfectly, with all computers able to access the files on the others exactly as one would expect. I installed Windows 8 Pro, which I downloaded recently from the MSDN website, on the laptop. From the info on the MSDN website, I believe the version downloaded is the official release version, not a release candidate. The install preserved all settings, apps, and files. I cannot connect to the homegroup from the laptop. Well, not exactly. I joined the homegroup during the install, and later left and rejoined, that was advertised as being offered by one of the pc's (not sure why that one was picked and not the other or both). This homegroup appears in my "computer" folder in the file explorer, offering files from that pc. But it excludes documents (only the music, pix, videos, and playlists folders on the one computer appear). I can actually access those files from the laptop. But the Homegroup folder, which actually shows all the computers by account and computer name and includes documents from both computers, does not open those folders when clicked. The computers listed by name in the Network folder give me a login that doesn't work. It asks for a username and password, no combinations of which work. Further, the following error message appears before the login is even attempted: "The system cannot contact a domain controller to service the authentication request. Please try again later." The two windows 7 pc's continue to share all files, including documents, seemlessly. I can also get to the laptop shared files, which I shared during setup, from either pc. Any ideas?

  Read the article

• hosts.deny ignored by MacOSX 10.8

  - by David Holm

  I have been trying to set up my MacOS X Server, which I recently upgraded to Mountain Lion, to use denyhosts as I need to open port 22 to it. denyhosts is set up and adds entries to /etc/hosts.deny so I decided to add my laptops IP to it in order to verify that it actually works but I can still log in and my IP shows up in /private/var/log/system.log. I even rebooted the server once just to be sure there wasn't some service that had to be restarted. I tried the following entries: ALL: <my laptop's IP> sshd: <my laptop's IP> sshd: 127.0.0.1 My /etc/sshd_config has the following parameters set: UsePAM yes UseDNS no I Googled if deny.hosts has been deprecated in OSX 10.7 or 10.8 but I couldn't find any indications that it has. Any ideas of what is going wrong or if there is an alternative way to achieve the same result? Yes, a private key would solve this problem but for the time being I would like to stick to using password authentication. I also like the idea of denyhosts actually blocking access to all services running on the server and not just ssh.

  Read the article

• Connect to WEP Wireless Network by command line on Ubuntu

  - by Tim

  Hi, I am a newbie to both network and Linux. I am now trying to connect to a WEP wireless network by command line on my Ubuntu 8.10, because the Network Manager does not support 64 bit WEP. (1) I firstly bring down the Network Manager and then try to connect to a wireless network, whose essid is candy and password is 5673212741. But it fails as shown in the following. I wonder why and how to do it correctly? $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo iwconfig wlan0 essid candy opendo iwconfig wlan0 key 18018ce78e open $ sudo iwconfig wlan0 key 5673212741 open $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 9971 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 20 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 13 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 9 No DHCPOFFERS received. No working leases in persistent database - sleeping. $ ping www.bbc.co.uk ping: unknown host www.bbc.co.uk (2) A less important question: why the scan for wireless networ does not work after I bring down the Network Manager? $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo iwlist wlan0 scan wlan0 Interface doesn't support scanning : Network is down Thanks and regards!

  Read the article

• Clarification for setting up SSH terminal access on Cisco IOS

  - by Matt Malesky

  I'm attempting to set up SSH on a Cisco 2811 and having some difficulties. The first step to this should be running crypto key generate rsa I seem to be missing this though: better#crypto key generate rsa ^ % Invalid input detected at '^' marker. better# Furthermore, the only available commands I have in the crypto key namespace are lock and unlock, which seem to indicate a locked keypair (for which I don't know the password): better#crypto key ? lock Lock a keypair. unlock Unlock a keypair. better#crypto key unlock ? rsa RSA keys better#crypto key unlock rsa %% Please enter the passphrase: %% Unlocking failed. . better# More or less, I'm asking what exactly this might mean, and if I actually do have certificates already here (used router)? Otherwise, how can I solve this? It's my first time configuring this feature, but I definitely believe it's part of my IOS. Speaking of my IOS, I'm running the image c2800nm-advsecurityk9-mz.124-24.T6.bin I'll also note that I have my hostname and ip domain-name configured. I'll also give you a dir flash: below if it's at all of use: better#dir flash: Directory of flash:/ 2 -rw- 2748 Jul 27 2009 14:03:52 +00:00 sdmconfig-2811.cfg 3 -rw- 931840 Jul 27 2009 14:04:10 +00:00 es.tar 4 -rw- 1505280 Jul 27 2009 14:04:32 +00:00 common.tar 5 -rw- 1038 Jul 27 2009 14:04:46 +00:00 home.shtml 6 -rw- 112640 Jul 27 2009 14:05:00 +00:00 home.tar 7 -rw- 1697952 Jul 27 2009 14:05:26 +00:00 securedesktop-ios-3.1.1.45-k9.pkg 8 -rw- 415956 Jul 27 2009 14:05:46 +00:00 sslclient-win-1.1.4.176.pkg 9 -rw- 38732900 Dec 8 2011 06:28:56 +00:00 c2800nm-advsecurityk9-mz.124-24.T6.bin 64016384 bytes total (20598784 bytes free) better#

  Read the article

• Backup script to FTP with timed subfolders

  - by Frederik Nielsen

  I want to make a backup script, that makes a .tar.gz of a folder I define, say fx /root/tekkit/world This .tar.gz file should then be uploaded to a FTP server, named by the time it was uploaded, for example: 07-10-2012-13-00.tar.gz How should such backup script be written? I already figured out the .tar.gz part - just need the naming and the uploading to FTP. I know that FTP is not the most secure way to do it, but as it is non-sensitive data, and FTP is the only option I have, it will do. Edit: I ended up with this script: #!/bin/bash # have some path predefined for backup unless one is provided as first argument BACKUP_DIR="/root/tekkit/world/" TMP_DIR="/tmp/tekkitbackup/" FINISH_DIR="/tmp/tekkitfinished/" # construct name for our archive TIME=$(date +%d-%m-%Y-%H-%M) if [ $1 ]; then BACKUP_DIR="$1" fi echo "Backing up dir ... $BACKUP_DIR" mkdir $TMP_DIR cp -R $BACKUP_DIR $TMP_DIR cd $FINISH_DIR tar czvfp tekkit-$TIME.tar.gz -C $TMP_DIR . # create upload script for lftp cat <<EOF> lftp.upload.script open server user user password lcd $FINISH_DIR mput tekkit-$TIME.tar.gz exit EOF # start backup using lftp and script we created; if all went well print simple message and clean up lftp -f lftp.upload.script && ( echo Upload successfull ; rm lftp.upload.script )

  Read the article

• Create a wifi hotspot in a place where an authentication is required

  - by SoftTimur

  I live in a residence where Internet is provided via cable. Once the computer is connected to the cable, launching a browser will trigger an authentication, I have a username and password to enter, then the internet will be connected. With a gateway (e.g. Wireless Cable Voice Gateway Model CBVG834G) and 2 cables, two PCs can connect to the Internet with my account at the same time. Now the question is, I don't like the cable, and would like to create a wifi hotspot. It seems realizable with the same gateway. According to the instruction on page 2-4 of the manual: Enter http://192.168.0.1 in the address field of your Internet browser. Log in to the gateway with either of the default user names, MSO or admin... However, while connecting to the Internet successfully via cable and the gateway (e.g. google works), opening 192.168.0.1 oddly gives me an error on the browser: Does anyone know what happened? Is it due to the authentication required by my residence? Is there any other way to build a hotspot of wifi? PS: My system is MAC OS

  Read the article

• Help about pure-ftp

  - by hai

  I setup pure-ftp on freebsd behind firewall. On pure-ftp setuped passsi mode ftp(rangle port 50400-50600) and firewall open port from 50400-50600 (include mode IN and out). But i try use ftp client connect but not connect. Nofinication error status: Connecting to 210.245.89.95:21... Status: Connection established, waiting for welcome message... Response: 220---------- Welcome to Pure-FTPd [privsep] ---------- Response: 220-You are user number 1 of 50 allowed. Response: 220-Local time is now 13:20. Server port: 21. Response: 220-IPv6 connections are also welcome on this server. Response: 220 You will be disconnected after 15 minutes of inactivity. Command: USER bk Response: 331 User bk OK. Password required Command: PASS Response: 230 OK. Current directory is / Command: SYST Response: 215 UNIX Type: L8 Command: FEAT Response: 211-Extensions supported: Response: EPRT Response: IDLE Response: MDTM Response: SIZE Response: REST STREAM Response: MLST type;size*;sizd*;modify*;UNIX.mode*;UNIX.uid*;UNIX.gid*;unique*; Response: MLSD Response: ESTA Response: PASV Response: EPSV Response: SPSV Response: ESTP Response: 211 End. Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is your current location Command: TYPE I Response: 200 TYPE is now 8-bit binary Command: PASV Response: 227 Entering Passive Mode (210,245,88,98,138,1) Command: MLSD Error: Connection timed out Error: Failed to retrieve directory listing Status: Connecting to 210.245.88.98:21... Status: Connection established, waiting for welcome message... Help me.

  Read the article

• SFTP, Chroot problems on Redhat

  - by Curtis_w

  I'm having problems setting up sftp with a ChrootDirectory. I've done an equivalent setup on other distros, but for some reason I cannot get it to work on a Redhat AMI. The changes to my sshd_config file are: Subsystem sftp internal-sftp Match Group ftponly PasswordAuthentication yes X11Forwarding no ChrootDirectory %h ForceCommand internal-sftp AllowTcpForwarding no I have the concerned usere's homes at /home/user, owned by root. After connecting with a user in the ftponly group, I'm dropped into / without permissions for anything, and am unable to do anything. sftp bob@localhost Connecting to localhost... bob@localhost's password: sftp> pwd Remote working directory: / I can connect normally with users not in the ftponly group. openssh version 5.3 I've experimented with different permissions, as well as having users own their own home directory (gives a Write failed: Broken pipe error), and so far, nothing has seemed to work. I'm sure it's a permissions error, or something equally as trivial, but at this point my eyes are beginning to glaze over, and any help would be greatly appreciated. EDIT: James and Madhatter, thanks for clarifying. I was confused by chroot dropping me in /... just didn't think through it properly. I've added the appropriate directories and permissions to get read access. One other key part was enabling write access to chrooted homes: setsebool -P ssh_chroot_rw_homedirs on in order to get write access. I think I'm all set now. Thanks for the help.

  Read the article

• Fedora 15: em1 recently dissapeared and hostapd no longer serves internet to wirelessly connected devices

  - by Daniel K

  I have a laptop running hostapd, phpd, and mysql. This laptop uses an Ethernet connection to connect to the internet and acts as a wireless access point for my workplace's wifi devices. After installing some software and reconnecting my Ethernet elsewhere, my "em1" device is no longer present and wirelessly connected devices can no longer reach the internet. The software I recently installed is: pptp, pptpd, and updated some fedora libraries. I have also recently moved my desk and laptop to another location and thus had to reconnect the Ethernet elsewhere. Wifi devices no longer have access to the internet. Wirelessly connected devices are able to successfully log into the laptop, showing full strength, correct SSID, and uses the proper password. However, when I tried to connect to a site like google, the request times out. The device "em1" also no longer appears on my machine. Running: # ifup em1 will give me the following output: ERROR : [/etc/sysconfig/network-scripts/ifup-eth] Device em1 does not seem to be present, delaying initialization. And running: # dhclient em1 has the following output: Cannot find device "em1" When I run # dmesg|grep renamed, I get the following: renamed network interface eth0 to p4p1. I've tried to connect to the internet through p4p1 directly from the laptop and was successful. However, my wireless devices connected to my laptop are not able to connect to the internet. I have uninstalled pptp and pptpd using # yum erase ... but the problem still persists. To install pptp I used: # yum install pptp To install pptpd I did the following: # rpm -Uvh http://poptop.sourceforge.net/yum/stable/fc15/pptp-release-current.noarch.rpm # yum install pptpd To update my fedora libraries I used: # yum check-update # yum update EDIT: Running # route produces the following results: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.11.200.1 0.0.0.0 UG 0 0 0 p4p1 10.11.200.0 * 255.255.252.0 U 0 0 0 p4p1 172.16.100.0 * 255.255.255.0 U 0 0 0 wlan0

  Read the article

• IIS 6 Windows Authentication in ASP.Net app fails

  - by Kjensen

  I am trying to install an ASP.Net app on an IIS6 webserver. The site requires the user to authenticate with windows, and this works on several other apps on the same server. In IIS I have enabled anonymous access and windows authentication. In web.config, authentication is set to: <authentication mode="Windows"/> and authorization...: <authorization> <allow roles="Users"/> <deny users="*"/> </authorization> Ie. allow all users in role "Users" and deny everybody else. This is the approach that is working with several other apps on the same server. If I run the site, I am prompted for username and password. If I remove the line: <deny users="*"/> I can access the site and everything works - but the user credentials are not passed to the site (Page.User.Identity.Name returns a blank string in ASP.Net). The site has identical (inherited) file permissions as other working sites on the server. The only difference in authentication/authorization between this site and the other working sites is, that this runs Asp.Net 4 (but there are other working asp.net 4 sites on the server as well). What am I missing here? Where should I look?

  Read the article

• cannot connect to vpn server (error 721)

  - by callmeblessed

  Hi I got 2 internet connections in my computer. One is using 3.5G HSDPA modem (vodafone huawei e220) and the other using mobile phone (cdma zte c261). Both are using different ISP and i have both. at the moment, i can connect to my office vpn using the HSDPA modem one. But when i tried to use cdma modem (dial up - mobile phone modem), i am just able to get "verifying username and password" and then after a few minutes it display error : Error 721 The Remote Computer didn't respond. I tried to ping into my office ip address, it got good result but still cannot connect to the vpn. I tried to turn off all my firewall (i'm using commodo) and has no response as well. In my cdma mobile phone modem Network connections I tried to allow iNternet connection sharing as well ... and turn on all Internet Protocol TCP/IP, File & Printer Sharing & Client for microsoft networks. But all of my effort has no effect. How to fix this problem ? note: my office using windows vpn as well. thank you .

  Read the article

• Prevent Windows from resizing all the apps on the desktop when switching monitors

  - by Greg Hewgill

  Short version: When moving my laptop and sleeping between using different monitors, all my open windows are crammed into the upper left corner as if they tried to fit on the laptop internal screen resolution. I plug in and switch to the external monitor before unlocking my session. Is there a way to prevent this automatic resizing? Longer version: I have a laptop that I move between two locations. I have one docking station, and the same kind of monitor configured for 1600x1200, in both locations. The internal laptop screen is awful so I don't use it. Location A: Docking station, monitor connected via DVI. Location B: No docking station, external monitor connected via VGA cable. In this location I have the laptop lid open for keyboard access but I don't use the laptop screen. When moving from Location A to Location B, the laptop wakes up from sleep, displaying the screen on the internal monitor. I switch to the external monitor display (using Fn+F8 on this laptop), and only after that do I unlock my session with my password. However, Windows has crammed all my nicely arranged windows into the upper left corner as if it were trying to fit them all on the laptop internal screen resolution. When moving from Location B to Location A, I have the laptop lid closed when using the docking station so Windows apparently concludes the screen resolution is 1600x1200 and doesn't resize any windows. The laptop is a Dell Latitude running Windows 7 Professional.

  Read the article

• Running multiple copies of openssh-server (sshd) on Ubuntu

  - by cecilkorik

  I may be attacking this problem the wrong way, if so let me know. I have a server which is available through SSH from both the public internet and the local LAN. I would like to have two very different security policies for each, by running two copies of sshd with two different sshd_config files each on a different port. Some of the things I'd like to change is to allow password or public-key authentication on the LAN, but public-key only from the internet. All (real) users could login from the LAN side, but only certain authorized users would be individually whitelisted to login through the internet. As far as I can tell this requires having two different SSH daemons running on different ports with different sshd_configs. I am fine with the different ports part, I can easily forward port 22 to any port I want through my firewall. So my question is what is the best way to actually START the second sshd under Ubuntu 10.04 LTS. Is there a recommended way to do something like this? Surely I am not the first person with this sort of need. I have a bit of experience with upstart, and I can manually hack the second sshd into /etc/init/ssh.conf I suppose but I'm not sure if that will get overwritten by the package. However I do it, It's important to ensure both sshd processes always get restarted after any automatic or manual upgrade of the openssh-server package. Thanks in advance.

  Read the article

• Administrative shares in Windows 7 Pro not visible

  - by Chris Tybur

  My desktop machine has a clean install of Windows 7 Professional. For some reason the standard administrative shares Admin$, C$, D$, etc are not visible, either in Computer Management - Shared Folders - Shares or via net share. I also have a laptop with a clean install of Windows 7 Professional, and I can see the admin shares in both places. As such, I can map to \\laptop\c$ from the desktop, but I can't map to \\desktop\c$ from the laptop. I pretty much took the defaults during the Windows 7 installations. I've tried adding LocalAccountTokenFilterPolicy to the registry on the desktop, but that didn't work. On the desktop I've also disabled UAC, turned off Windows firewall, removed it from a homegroup, made sure file and printer sharing is turned on, but nothing has worked. There is some subtle difference between the two machines that I can't seem to find. I'm logging into both machines using a local account that is in the Administrators group. Both accounts have the same name and password. I really don't want to have to create a new share for the desktop's C drive, especially since C$ is visible and working on the laptop and therefore I should be able to make it work on the desktop. Any idea why the admin shares would work on one machine and not another? Or why LocalAccountTokenFilterPolicy would fail?

  Read the article

• Running phpmyadmin xampp Ubuntu 12.10

  - by Luigi Tiburzi

  I know it is a common problem and there are many solutions on the web but I'm trying everything and anything is working, I can't have phpmyadmin running on my machine. I installed XAMPP through: sudo tar xvfz ./Downloads/xampp-linux-1.8.1.tar.gz -C /opt then I did the chmod trick supposed to make an end to access issues and I change the default location to my php projects from /var/www to Dropbox/php. Then I started XAMPP in the usual way: sudo /opt/lampp/lampp start When I tried to run one of my php projects the output on the web is fine but if for example I try to write localhost on my browser I get: It works and not the usual XAMPP interface and most of all when I try to access localhost/phpmyadmin I get the login page, insert username (root) and password and I get: You don't have permission to access /phpmyadmin/index.php on this server. Apache/2.2.22 (Ubuntu) Server at localhost Port 80 I tried the Required all granted trick and some others but nothing is working. I even tried to uninstall phpmyadmin and reinstall it but this is not working too. I don't know hot to proceed. Thanks for your help.

  Read the article

• Why do I have to log into hotmail twice?

  - by Tony Lee

  I just recently noticed I have to attempt a login into hotmail twice before it succeeds. Although I'm using Google Chrome (3.0.195.21), the symptoms are well described in a Mozilla thread. In short, I'm told: The e-mail address or password is incorrect. Please try again. The thread on mozilla's site that supposed to describe the latest details (and the 1st hit on google when I search for "hotmail login twice") requires an account to read so I'm hoping someone here has a good synopsis of what the cause is. I normally start at hotmail.com, which redirects to login.live.com/.... I can login by starting at mail.live.com, using IE8 or attempting a 2nd login. Oddly, if I start at login.live.com Chrome tells me there is a redirect loop. Does anyone know or have a public link to the root cause of the double login? (it is a hotmail account I'm login into) EDIT - Caused by my 'restricting how 3rd parties can use cookies'. If I allow all cookies, it works first time.

  Read the article

• Understanding tcptraceroute versus http response

  - by kojiro

  I'm debugging a web server that has a very high wait time before responding. The server itself is quite fast and has no load, so I strongly suspect a network problem. Basically, I make a web request: wget -O/dev/null http://hostname/ --2013-10-18 11:03:08-- http://hostname/ Resolving hostname... 10.9.211.129 Connecting to hostname|10.9.211.129|:80... connected. HTTP request sent, awaiting response... 200 OK Length: unspecified [text/html] Saving to: ‘/dev/null’ 2013-10-18 11:04:11 (88.0 KB/s) - ‘/dev/null’ saved [13641] So you see it took about a minute to give me the page, but it does give it to me with a 200 response. So I try a tcptraceroute to see what's up: $ sudo tcptraceroute hostname 80 Password: Selected device en2, address 192.168.113.74, port 54699 for outgoing packets Tracing the path to hostname (10.9.211.129) on TCP port 80 (http), 30 hops max 1 192.168.113.1 0.842 ms 2.216 ms 2.130 ms 2 10.141.12.77 0.707 ms 0.767 ms 0.738 ms 3 10.141.12.33 1.227 ms 1.012 ms 1.120 ms 4 10.141.3.107 0.372 ms 0.305 ms 0.368 ms 5 12.112.4.41 6.688 ms 6.514 ms 6.467 ms 6 cr84.phlpa.ip.att.net (12.122.107.214) 19.892 ms 18.814 ms 15.804 ms 7 cr2.phlpa.ip.att.net (12.122.107.117) 17.554 ms 15.693 ms 16.122 ms 8 cr1.wswdc.ip.att.net (12.122.4.54) 15.838 ms 15.353 ms 15.511 ms 9 cr83.wswdc.ip.att.net (12.123.10.110) 17.451 ms 15.183 ms 16.198 ms 10 12.84.5.93 9.982 ms 9.817 ms 9.784 ms 11 12.84.5.94 14.587 ms 14.301 ms 14.238 ms 12 10.141.3.209 13.870 ms 13.845 ms 13.696 ms 13 * * * … 30 * * * I tried it again with 100 hops, just to be sure – the packets never get there. So how is it that the server does respond to requests via http, even after a minute? Shouldn't all requests just die? I'm not sure how to proceed debugging why this server is slow (as opposed to why it responds at all).

  Read the article

• How can I make an encrypted email message into a .p7m file?

  - by Blacklight Shining

  This is a bit complicated, so I'll explain what I'm really trying to do here: I have a Debian server, and I want to automatically email myself certain logs every week. I'm going to use cron and a bash script to copy the logs into a tarball shortly after midnight every Monday. A bash script on my home computer will then download the tarball from the server, along with a file to be used as the body of the email, and call an AppleScript to make a new email message. This is where I'm stuck—I can't find a way to encrypt and sign the email using AppleScript and Apple's mail client. I've noticed that if I put a delay in before sending the message, Mail will automatically set it to be encrypted and signed (as it normally does when I compose a message myself). However, there's no way to be sure of this when the script runs—if something goes wrong there, the script will just blindly send the email unencrypted. My solution there would be to somehow manually create a .p7m file with the tarball and message and attach it to the email the AppleScript creates. Then, when I receive it, Mail will treat it just like any other encrypted message with an attachment (right?) If there's a better way to do this, please let me know. ^^ (Ideally, everything would be done from the server, but there doesn't seem to be a way to send mail automatically without storing a password in plaintext.) (The server is running Debian squeeze; my home computer is a Mac running OS X Lion.)

  Read the article

• How to share text, pictures and video to restricted set of users

  - by joaoc

  I want to share pictures and videos of my kid growing up but I don't want it to be open to the public. I just want me and my wife to be able to add material and then share with grandparents and friends who would be given a username/password or some other solution that authenticates them. This content would preferably be available remotely over the internet or downloaded periodically to the allowed viewers computers. The second option most likely means they would have to install a client, which I am not too fond of doing (I would have to ask them to install it, help configure for different platforms, ...) I'm at the start but I would like software that also allows export of the data (if one day I want to migrate to a different solution). Folder sharing I don't know if Windows folder sharing is reliable, robust and safe enough to share over the internet. Dropbox could be a software solution, but it's limited to 2GB and requires receivers to also install and configure software. A folder is just a collection of files, so it would be harder to keep them organized with text describing the pictures/video Email I could email the content every now and then but videos are almost always too big to go as attachments This would also not provide a history of updates to anyone just recently joining in Are there other solutions to achieve this? NOTE: I also thought that software to run a local or remote blog could be an option but we aren't allowed to ask those questions on superuser because one admin doesn't like cloud-computing questions. But if you do think it's the best approach and can suggest a solution, do state it in the answers anyway!

  Read the article

• Vlaning on WNR3500L

  - by ageis23

  When I try connecting to my wireless network it attempts to connect then gives up. There's something strange going on with the mac's. The eternet switch and all the vlan interfaces have a mac 00:FF:FF:FF:FF:FF. config 'switch' 'eth0' option 'vlan0' '2 3 4 8*' option 'vlan1' '0 8' option 'vlan2' '1 8' config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'lan' option 'type' 'bridge' option 'ifname' 'eth0.1' option 'proto' 'static' option 'netmask' '255.255.255.0' option 'ipaddr' '192.168.2.1' option 'ip6addr' '' option 'gateway' '192.168.1.253' option 'ip6gw' '' option 'dns' '' config 'interface' 'wan' option 'ifname' 'eth0' option 'proto' 'dhcp' option 'ipaddr' '192.168.1.8' option 'ip6addr' '' option 'netmask' '255.255.255.0' option 'gateway' '192.168.1.253' option 'ip6gw' '' option 'dns' '192.168.1.253' config 'interface' 'dmz' option 'ifname' 'eth0.2' option 'proto' 'static' option 'ipaddr' '192.168.0.1' option 'netmask' '255.255.255.0' Any help on this will be greatly appreciated! When I try setting the mac using macaddr it does nothing. It works perfectly fine when I turn the authentication off. I've also discovered that when wpa2 is switched on I don't receive a association reply from ap. thats my hostapd.conf interface=eth1 driver=broadcom bridge=br-lan ssid=O2BB3 wpa=2 wpa_passphrase=prettywoman wpa_key_mgmt=WPA-PSK rsn_pairwise=CCMP Btw that password is only temporary while am testing.

  Read the article

• server 2008 r2 stuck on installing updates

  - by volody

  I have 2008 r2 64bit server that is stuck on installing updates. It shows message "Please do not power off or unplug your machine. Installing 57 of 61.." This message is shown for 3 hours now. I was trying to connect to this server using mmc. runas /user:AdministratorAccountName@ComputerName "mmc %windir%\system32\compmgmt.msc" RUNAS ERROR: Unable to run - mmc C:\Windows\system32\compmgmt.msc 1311: There are currently no logon servers available to service the logon request. What else can I do? Update: Remote Desktop does not work. It just disappear after entering username and password from Win7-64 computer Update: I have disconected server. Now Server Manager in Roles Summary shows message "Unexpected error refreshing Server Manager: The remote procedure call failed." Event log shows Could not discover the state of the system. An unexpected exception was found: System.Runtime.InteropServices.COMException (0x800706BE): The remote procedure call failed. (Exception from HRESULT: 0x800706BE) at System.Runtime.InteropServices.Marshal.ThrowExceptionForHRInternal(Int32 errorCode, IntPtr errorInfo) at Microsoft.Windows.ServerManager.ComponentInstaller.ThrowHResult(Int32 hr) at Microsoft.Windows.ServerManager.ComponentInstaller.CreateSessionAndPackage(IntPtr& session, IntPtr& package) at Microsoft.Windows.ServerManager.ComponentInstaller.InitializeUpdateInfo() at Microsoft.Windows.ServerManager.ComponentInstaller.Initialize() at Microsoft.Windows.ServerManager.Common.Provider.RefreshDiscovery() at Microsoft.Windows.ServerManager.LocalResult.PerformDiscovery() at Microsoft.Windows.ServerManager.ServerManagerModel.CreateLocalResult(RefreshType refreshType) at Microsoft.Windows.ServerManager.ServerManagerModel.InternalRefreshModelResult(Object state) Update: Manual update hangs on (Installing update 58 of 62...) Seurity Update for Windows Server 2008 R2 x64 Edition (KB979309) Update: It could be an issue with that admin user was renamed

  Read the article

< Previous Page | 397 398 399 400 401 402 403 404 405 406 407 408  | Next Page >