Search Results

Search found 21945 results on 878 pages for 'online services'.

Page 402/878 | < Previous Page | 398 399 400 401 402 403 404 405 406 407 408 409  | Next Page >

  • "No more threads can be created in the system" in Network and Sharing Center

    - by Zell Faze
    A while back I noticed on one of our laboratory computers (Windows 7, very little extra software installed) that the network connection icon in the system tray would claim that it had no network connection, even though it did. This issue would go away after the computer was rebooted, but would surface again the next time I looked at the computer (a few days later). Upon opening the Network and Sharing Center I am shown an actual error message, but not one that seems to give me a lot of information about what the problem is. In the place of the usual information about network adapters and whether you are connected to the Internet it simply says: "No more threads can be created in the system." The Event Viewer shows hundreds of events from different services also with the same message. "Volume Shadow Copy Service error: Unexpected error calling routine CoCreateInstance. hr = 0x800700a4, No more threads can be created in the system."; "The WinHTTP Web Proxy Auto-Discovery Service service failed to start due to the following error: A thread could not be created for the service."; "The IP Helper service terminated with the following error: No more threads can be created in the system." As far as I can tell, this message seems to mean that there is some sort of resource leak in Windows where something is creating a large number of threads and those threads are not being killed off? I've tried restarting WMI and several services related to networking, without avail. Can anyone provide more information on what "No more threads can be created in the system" might mean and what I might be able to do to fix the issue? Currently the only solution appears to be restarting.

    Read the article

  • 4in6 tunneling (via OpenVPN?)

    - by Deshene
    I have a local network with internet access. But unfortunately IPv4 internet connection speed is limited to 1mbps, which is realy sad. Fortunately I have a native IPv6, and there is no connection speed limit over IPv6. So, in order to get a good internet connection I made a plan: connect to the VPN-service over IPv6, and pass all IPv4 traffic through IPv6 tunnel, or something like that, I think you get the idea. I suggested to use service like HideMyAss.com, but unfortunately they don't support IPv6. The question is: Is there any existing VPN service that will make my dreams come true, and is easy to use, which I could connect over PPTP or OpenVPN (I want to set up connection to VPN in my router settings). Edit: It seems like there are couple of VPN services that supports IPv6 (it's odd, but the biggest VPN services support only IPv4), and there is none providing 4in6 tunnels. So, I came to the following solution: rent a VPS with IPv6 address, and manually setup 4in6 tunnel. I'm not good at networking, never did things like that, and don't know where to start, and what should I do. The use case, as I undestand, should look like this: I connect from my home computer to the VPS via OpenVPN, and after that all my IPv4 traffic pass through IPv6 (server do the job). OpenVPN - because I want to configure VPN connection to server in my router (Asus RT-N16?). How can I achieve this?

    Read the article

  • Issues with doing a P2V on Exchange 2007

    - by PokermUNKEE
    I shutdown all Exchange services on the physical box and did a convert. Everything converted fine. Server booted up no issues and I could receive email from the outside world with no issues. But I am unable to send emails internally or externally. They just sit in the Outbox. I also disabled the DHCPClient service as I didn't want the server to get an IP address from DHCP when it first came online. It came online with no IP, then I used console to assign the correct static IP address (same one on the physical server) and rebooted. I ran the Exchange Troubleshooting Agent and it gave me the following errors: The value for the '\MSExchangeIS Mailbox\Messages Queued For Submission' counter on server exchange is greater than zero (average value is 8.8) and it appears that 'MSExchangeMailSubmission' is failing to submit messages to at least one computer with the Hub Transport server role installed over the last minute. Found 1 computers with the Hub Transport server role installed in the same Active Directory site as server exchange using local Active Directory site GUID 'ce8a4367-1bf6-4825-9cac-c4e2b115c450'. Check Local Active Directory Site Hub Transport Server Role Health (Mailflow_CheckLocalBhHealth1.1.1.1.1.1.1.1) I have one Exchange server with all the roles on it. Has anyone see this before when doing a convert? Please help :(

    Read the article

  • Debugging UI Problems in IE8 (Was IE8 on Windows 7 Authentication Mess)

    - by alharaka
    UPDATE: I think the real question I need to ask here is: how does a technician debug UI problems with Internet Explorer, and not HTML rendering issues that have pretty good tools? I am aware of the SysInternals tools and others mentioned below, but maybe I am not harnessing their power properly. Someone else in the TechNet forum I mentioned had a similar issue. Again, I have lots of data, I am not sure how to properly interpret it. ORIGINAL POST: So I tried the venerable Technet Forums to solve this isse. In short, the Windows Security dialog has no place to put credentials, rendering pretty much useless. This happens to apply for a whole bunch of our intranet websites, and only a select number of users with a few laptops have this problem. It ends up looking like this. Things I have tried so far: Disabling local Group Policy (not domain connected) Disabling local Security Policy Resetting IE settings A few system restores Re-registering a bunch of IE DLL's and all other steps here Reinstalling IE8 (dism /online /disable-feature /featurename:"internet-explorer-optional-x86, reboot, dism /online /enable-feature /featurename:"internet-explorer-optional-x86, and reboot) And SFC scan, which found nothing Still, nothing. Not only am I fed up, but I have begun to really work with APIExplorer and Procmon as mentioned in the Technet original because I want to know WHAT is happening, not just fix it. Any thoughts?

    Read the article

  • Server 2008 R2 Dns Lockup

    - by Richard Maynard
    Hi, We've deployed our first 2008 R2 server on a client site which has replaced their existing 2003 DC. This server provides DNS resolution services to all client machines on that site for general internet usage. Since using the 2008 R2 DNS services we have noticed every couple of days the DNS server starts timing out when requests to certain sites are made (google is the only example I can provide at this time although it seems to be larger sites with problems rather than small - CDN compatiblity issue?). When you restart the DNS Server service then resolution returns to normal... just only for a day or so. Is anybody aware of any significant changes to the DNS server architecture or configuration out of the box in R2 that may explain this intermittent behaviour? I have already tried the fix listed here to no avail: http://weblogs.asp.net/owscott/archive/2009/09/15/windows-server-2008-r2-dns-issues.aspx The following PS command prompt info illustrates the issue: PS C:\Users\Administrator.UK> nslookup Default Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 > www.google.com Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 Non-authoritative answer: Name: www.l.google.com Addresses: 66.102.9.99 66.102.9.104 66.102.9.105 66.102.9.103 66.102.9.147 Aliases: www.google.com > www.google.co.uk Server: s8209001.uk.kingdomfaith.com Address: 10.1.3.4 * s8209001.uk.kingdomfaith.com can't find www.google.co.uk: Server failed Thanks in advance. Regards,

    Read the article

  • Oracle® Database Express Edition roblem running on Win Server 2003 with MS SQl Server 2008 [closed]

    - by totoz
    Hi I have on Win Server 2003 MS SQL Server 2008 and also IIS is running. I try learn Oracle, so first I installed Oracle® Database Express Edition. I tried connect viac web browser on Oracle Server on url http://127.0.0.1:8080/apex I got this expcetion in browser The page cannot be found The page you are looking for might have been removed, had its name changed, or is temporarily unavailable. Please try the following: Make sure that the Web site address displayed in the address bar of your browser is spelled and formatted correctly. If you reached this page by clicking a link, contact the Web site administrator to alert them that the link is incorrectly formatted. Click the Back button to try another link. HTTP Error 404 - File or directory not found. Internet Information Services (IIS) Technical Information (for support personnel) Go to Microsoft Product Support Services and perform a title search for the words HTTP and 404. Open IIS Help, which is accessible in IIS Manager (inetmgr), and search for topics titled Web Site Setup, Common Administrative Tasks, and About Custom Error Messages. Why I can not log on Oracle Home Page?

    Read the article

  • Antivirus Configuration for dedicated SQL and dedicated IIS Servers

    - by Wayne Arthurton
    Our corporate standard is McAfee Enterprise, unfortunately this is non-negotiable. On two types of servers I'm responsible for, SQL & Web, we have noticed major performance issues with the corporate standard setup. Max scan time 45sec One policy for all processes Scan ALL files on write, read and open for backup Heuristics: Find unknown programs, trojans and macros Detect unwanted programs Exclude: EVT, LDF, LOG, MDF, VMD, , windows file protection) This of course still causes major slowdowns. IIS .NET recompiles are slow especially with SharePoint, SQL backups and restores, SQL Analysis Services, Integration Services and temp data from them as well. I have looked from time to time, for some best practices on setting up McAfee of SQL & SQL Analysis Service, SQL Integration Service, Visual Studio, Sharepoint, and .NET web servers in general. How do people setup McAfee enterprise on their corporate serves keeping security intact, but affecting performance as minimally as possible? Has anyone run across white papers on these setups? Obviously some are case by case, but there must be some best practices out there somewhere.

    Read the article

  • What is Apache Synapse?

    - by Aren B
    My website keeps getting hit by odd requests with the following user-agent string: Mozilla/4.0 (compatible; Synapse) Using our friendly tool Google I was able to determine this is the hallmark calling-card of our friendly neighborhood Apache Synapse. A 'Lightweight ESB (Enterprise Service Bus)'. Now, based on this information I was able to gather, I still have no clue what this tool is used for. All I can tell is that is has something to do with Web-Services, and supports a variety of protocols. The Info page only leads me to conclude it has something to do with proxies, and web-services. The problem I've run into is that while normally I wouldn't care, we're getting hit quite a bit by Russian IPs (not that russian's are bad, but our site is pretty regionally specific), and when they do they're shoving wierd (not xss/malicious at least not yet) values into our query string parameters. Things like &PageNum=-1 or &Brand=25/5/2010 9:04:52 PM. Before I go ahead and block these ips/useragent from our site, I'd like some help understanding just what is going on. Any help would be greatly appreciated :)

    Read the article

  • Any Recommendations for a Web Based Large File Transfer System?

    - by Glen Richards
    I'm looking for a server software product that: Allows my users to share large files with: The general public securely to 1 or more people (notification via email, optionally with a token that gives them x period of time to download) Allows anyone in the general public to share files with my users. Perhaps by invitation. Has to be user friendly enough to allow my users to use this with out having to bug me as the admin. It needs to be a system that we can install on our own server (we don't want shared data sitting on anyone else's server) A web based solution. Using some kind or secure comms channel would be good too, eg, ssh Files to share could be over 1 GB. I found the question below. WebDav does not sound user friendly enough: http://serverfault.com/questions/86878/recommendations-for-a-secure-and-simple-dropbox-system I've done a lot of searching, but I can't get the search terms right. There are too many services that provide this, but I want something we can install on our own server. A last resort would be to roll my own. Any ideas appreciated. Glen EDIT Sorry Tom and Jeff but Glen specifically says that he's looking for a 'product' so given that I specialise in this field thought that my expertise in this area may have been of use to him. I don't see how him writing services is going to be easy for him to maintain going forward (large IT admin overhead) or simple for his users and the general public to work with.

    Read the article

  • Setting up SQL Server 2005 to use all available memory in 32bit Windows Server 2003 - and verifying

    - by Rizwan Kassim
    There are a number of questions along this line - but they either sometimes contradict each other, or don't show how to properly verify that everything is actually working - hopefully this can be comprehensive... I'm running SQL Server 2005 SP3 Standard on Windows Server 2003 R2 Standard. My server has 8GB of memory installed - my system is almost entirely used as a Database Server - there are some services running on them, but the OS + services can run within 1Gb of RAM. What I've done (please tell me if I'm doing something wrong): /3GB in the boot.ini. (To increase the amount of user-space memory available - info) /PAE in the boot.ini. (Windows claimed to be doing PAE even without this switch, somethow.) Enabled AWE in SQL Server. Enabled Lock Pages in Memory Option for users SYSTEM and Local Service. (info). SQL Server Standard doesn't seem to use this until Cumulative Update 4, which isn't installed on my server. (info) Set Min/Max Memory to : 1024Mb/5112Mb After doing all the above, we definately saw a level of improvement - but I'd like now to verify my settings, make sure that I'm making full use of the memory available. (There appeared to be a slowdown when max = 7Gb, so I edged off from that value, but it might have been just perceptual.) To verify, I checked the following levels in PerfMon : Process(sqlserv):Working Set : 76386304 SQL Server(Memory Manager) : Total Server Memory : 3538944 (I saw a doc that noted that this wasn't the full memory used by SQL Server, so I'm not sure whether to trust it) So -- my questions... Should my max be around 7Gb? If not, what should it be? Why is total server memory at 3.5G, when it's been allocated 5G? What is the proper metric for the amount of memory allocated to SQL Server? The Working Set seems a bit large... Am I possibly missing any steps in the setup? Any recommended resources on starting to tune the caching system now? Thanks

    Read the article

  • Debian and Multipath IO problem

    - by tearman
    Basically the situation is, I have a box running Debian, the box internally has an Intel SCSI RAID controller which is controlling 2 hard drives in RAID1 mode which is where the OS is installed. Further, I have a QLogic fiber channel adapter that connects the unit to a Fiber Channel SAN. My process of installation is I'll install Debian to the local drives, and leave the QLogic firmware out of it for the time being. Then once I get the unit online, I'll install the firmware drivers. This flops my internal drives from /dev/sda to /dev/sdc, which is a bit annoying, but recoverable. Probably should address these by UUID anyways. Once I get back online, I have to install multipath-tools (the framework is a multipath framework). However, once I reboot the machine again, it fails on boot after discovering multipath targets, saying my local drives are busy and cannot be mounted to /root. Any help in what may be the problem here? Or at least how to disable multipath until after the unit boots and then ignores the internal drives?

    Read the article

  • How to know if your computer is hit by a dnschanger virus?

    - by kira
    The Federal Bureau of Investigation (FBI) is on the final stage of its Operation Ghost Click, which strikes against the menace of the DNSChanger virus and trojan. Infected PCs running the DNSChanger malware at unawares are in the danger of going offline on this coming Monday (July 9) when the FBI plans to pull down the online servers that communicate with the virus on host computers. After gaining access to a host PC, the DNSChanger virus tries to modify the DNS (Domain Name Server) settings, which are essential for Internet access, to send traffic to malicious servers. These poisoned web addresses in turn point traffic generated through infected PCs to fake or unsafe websites, most of them running online scams. There are also reports that the DNSChanger virus also acts as a trojan, allowing perpetrators of the hack attack to gain access to infected PCs. Google issued a general advisory for netizens in May earlier this year to detect and remove DNSChanger from infected PCs. According to our report, some 5 lakh PCs were still infected by the DNSChanger virus in May 2012. The first report of the DNSChanger virus and its affiliation with an international group of hackers first came to light towards the end of last year, and the FBI has been chasing them down ever since. The group behind the DNSChanger virus is estimated to have infected close to 4 million PCs around the world in 2011, until the FBI shut them down in November. In the last stage of Operation Ghost Click, the FBI plans to pull the plug and bring down the temporary rogue DNS servers on Monday, July 9, according to an official announcement. As a result, PCs still infected by the DNSChanger virus will be unable to access the Internet. How do you know if your PC has the DNSChanger virus? Don’t worry. Google has explained the hack attack and tools to remove the malware on its official blog. Trend Micro also has extensive step-by-step instructions to check if your Windows PC or Mac is infected by the virus. The article is found at http://www.thinkdigit.com/Internet/Google-warns-users-about-DNSChanger-malware_9665.html How to check if my computer is one of those affected?

    Read the article

  • Setting up ProxyPass for a Virtualmin virtual server

    - by Andy Ibanez
    I am trying to set up my web server so that I can server multiple Ghost.org blogs. I am stuck in one crucial step. To be honest, my knowledge in servers is not so big, so I request your help to do this. Basically, a tutorial I'm reading suggests I set up a VirtualHost in this way: NameVirtualHost *:80 <VirtualHost *:80> ServerName your-url.com ServerAlias www.your-url.com ProxyRequests off ProxyPass / http://127.0.0.1:2368/ ProxyPassReverse / http:/127.0.0.1:2368/ </VirtualHost> So I have gone to the Virtual site on Virtualmin to try to add everything as is. Services Configure Website Edit Directives The problem is, the previous page (Services Configure website) says I can't edit the port: This Apache virtual host belongs to the Virtualmin server linguist.andyibanez.com, so the address, port, base directory and hostname cannot be changed here. And whenever I try to add the ProxyRequests off (the other two can be added fine) directive in Edit Directives manually, I'm simply told that the directive can't be there. So what is the right way to "add" the last three directives in the VirtualHost above to my sub server? Maybe I'm missing a menu item that will help me with this? I request your help as I have looked for a while, Google keeps thinking I want to serve Webmin via Apache when I google "Set up Virtualmin proxypass", and I have no clue what to do.

    Read the article

  • Debugging UI Problems in IE8 (Was IE8 on Windows 7 Authentication Mess)

    - by alharaka
    UPDATE: I think the real question I need to ask here is: how does a technician debug UI problems with Internet Explorer, and not HTML rendering issues that have pretty good tools? I am aware of the SysInternals tools and others mentioned below, but maybe I am not harnessing their power properly. Someone else in the TechNet forum I mentioned had a similar issue. Again, I have lots of data, I am not sure how to properly interpret it. ORIGINAL POST: So I tried the venerable Technet Forums to solve this isse. In short, the Windows Security dialog has no place to put credentials, rendering pretty much useless. This happens to apply for a whole bunch of our intranet websites, and only a select number of users with a few laptops have this problem. It ends up looking like this. Things I have tried so far: Disabling local Group Policy (not domain connected) Disabling local Security Policy Resetting IE settings A few system restores Re-registering a bunch of IE DLL's and all other steps here Reinstalling IE8 (dism /online /disable-feature /featurename:"internet-explorer-optional-x86, reboot, dism /online /enable-feature /featurename:"internet-explorer-optional-x86, and reboot) And SFC scan, which found nothing Still, nothing. Not only am I fed up, but I have begun to really work with APIExplorer and Procmon as mentioned in the Technet original because I want to know WHAT is happening, not just fix it. Any thoughts?

    Read the article

  • Windows 2008 RemoteAPP client disconnects within a matter of minutes

    - by Jeroen Wilke
    I'm having an odd problem with Windows 2008 TS, and remote applications specifically. The situation is as follows: TS idle timeout is disabled via GPO TS terminating disconnected sessions after 1hr (via GPO) My users can log on to the Terminal server, and get a full desktop, OR via rdp files that give access to a few remote applications. When a user connects to a full desktop, everything is fine and dandy, they will remain logged on indefinately, and when they disconnect the session is terminated after an hour. however, when a user connects using a remote application link, the client seems to disconnect after only a few minutes of inactivity, when you click the window, the session reconnects. EventID's on TS server: 4779: This event is generated when a user disconnects from an existing Terminal Services session, or when a user switches away from an existing destop using Fast User Switching. 4778 : This event is generated when a user reconnects to an existing Terminal Services session, or when a user switches to an existing desktop using Fast User Switching users are connecting directly to 3389, not using a TS-gateway at the moment. This behavior is consistent on different clients that we have, Full desktop is fine, RemoteAPP constantly disconnects. The .rdp file used doesn't list any interesting parameters, aside from what application to launch, and where to find it. Can someone explain to me how there can be a difference in behaviour between full desktop, and remoteapp ? since essentially they use the exact same client ? Regards Jeroen

    Read the article

  • Error in data view when connecting to an Oracle DB

    - by Mike Polen
    When using SharePoint Designer I found this link that stepped me through how to get it working: http://spsolution.blogspot.com/2008/12/how-to-insert-data-source-in-sharepoint.html That allowed SharePoint Designer to talk to Oracle, but when I placed a data view on a page it gave me the following error: Error while executing web part: System.Data.OracleClient.OracleException: ORA-00923: FROM keyword not found where expected at System.Data.OracleClient.OracleConnection.CheckError(OciErrorHandle errorHandle, Int32 rc) at System.Data.OracleClient.OracleCommand.Execute(OciStatementHandle statementHandle, CommandBehavior behavior, Boolean needRowid, OciRowidDescriptor& rowidDescriptor, ArrayList& resultParameterOrdinals) at System.Data.OracleClient.OracleCommand.Execute(OciStatementHandle statementHandle, CommandBehavior behavior, ArrayList& resultParameterOrdinals) at System.Data.OracleClient.OracleCommand.ExecuteReader(CommandBehavior behavior) at System.Data.OracleClient.OracleCommand.ExecuteDbDataReader(CommandBehavior behavior) at System.Data.Common.DbCommand.Syst... 09/14/2009 14:40:23.52* w3wp.exe (0x0FA0) 0x1A88 Windows SharePoint Services Web Parts 89a1 Monitorable ... em.Data.IDbCommand.ExecuteReader(CommandBehavior behavior) at System.Data.Common.DbDataAdapter.FillInternal(DataSet dataset, DataTable[] datatables, Int32 startRecord, Int32 maxRecords, String srcTable, IDbCommand command, CommandBehavior behavior) at System.Data.Common.DbDataAdapter.Fill(DataSet dataSet, Int32 startRecord, Int32 maxRecords, String srcTable, IDbCommand command, CommandBehavior behavior) at System.Data.Common.DbDataAdapter.Fill(DataSet dataSet, String srcTable) at System.Web.UI.WebControls.SqlDataSourceView.ExecuteSelect(DataSourceSelectArguments arguments) at System.Web.UI.DataSourceView.Select(DataSourceSelectArguments arguments, DataSourceViewSelectCallback callback) at Microsoft.SharePoint.WebControls.SingleDataSource.GetXPathNavigatorInternal() ... 09/14/2009 14:40:23.52* w3wp.exe (0x0FA0) 0x1A88 Windows SharePoint Services Web Parts 89a1 Monitorable ... at Microsoft.SharePoint.WebControls.SingleDataSource.GetXPathNavigator() at Microsoft.SharePoint.WebControls.SingleDataSource.GetXPathNavigator(IDataSource datasource, Boolean originalData) at Microsoft.SharePoint.WebPartPages.DataFormWebPart.GetXPathNavigator(String viewPath) at Microsoft.SharePoint.WebPartPages.DataFormWebPart.PrepareAndPerformTransform() I am mystified.

    Read the article

  • TomTom GO & Ubuntu Linux: impersonating a GPRS phone with dund

    - by Broam
    Background: I've called TomTom support, and they don't support Linux. I can get my GO 730 to mount Mass Storage, and I found a shell script that will allow me to install maps (haven't tried it; will update when I do.). As of note: USB 2.0 only. 1.1 ports will not work. However--I still can't update the TomTom or take advantage of any traffic services. The GO will connect to a mobile phone, but I don't have one that supports tethering. However, I've found a site that claims to know a way to get a Linux Machine to impersonate a phone advertising GPRS services and it apparently works in Fedora as old as FC4. I'm having some serious trouble getting this to work on Ubuntu 9.10 Karmic, mainly because I think some of the built-in bluetooth stuff is getting in the way. Changing the class bits in main.conf (hcid.conf does not exist) doesn't crash..., and dund starts and listens, but the TomTom device never seems to want to connect to my machine. I haven't played around much with sdcptool (I think that's the name, not in front of a Linux machine right now) but maybe I have to advertise the DUN profile...I'm not very sure. My Question: I have no way to diagnose the problems. What are some diagnostic tools I can use to help dig down and figure out what's going on? Update: apparently dund is a legacy tool that's going away. What replaces it?

    Read the article

  • Backup program for Windows using non-proprietary format?

    - by Cristi Diaconescu
    I'm looking at the various local backup programs for windows, and I was wondering which of them use a non-proprietary backup format? By non-proprietary, I mean I want to be able to access at least the latest version of the backed up files either directly, or by using an open-standard format like zip/7z/rdiff... The other thing I'm looking for in a backup program is the ability to create incremental backups. What I have found so far: SyncBack copies files as-is, using separate directories for versioning pretty much the same for all the 'roll you own' task scheduler + rsync/xcopy32/robocopy/MS SyncToy/etc solutions GFI Backup appears to be using Zip files, at least in their 'Business' version, not sure about the free 'Home' version. Didn't try it yet, but it's next on my list. Mozy (!) supports local backup starting with v 2.0 and basically provides a 2nd local copy on a separate partition. Subjectively, it feels slow and resource intensive (I think it took more than a week to finish the first local backup of ~ 300 GB), and does not appear to offer file versioning (arguably, you can get older file versions online). On the positive side, it looks like the local backup is integrated in the restore process which was traditionally a masochistic experience (and this goes for any online backup provider). Other suggestions? I favor ease of use over tons of options (e.g. SyncBack is very flexible but it offers sooo many ways to shoot yourself in the foot...)

    Read the article

  • Maximum RAM on Biostar P4M8PM7 Socket775 mATX board

    - by Alex Balashov
    I have a server with a Biostar P4M8PM7 ("Pro-M7") board based on a VIA chipset. It's a strange board to put in a server because it seems like more of a desktop board to me, but alas! It takes DDR2-667 (PC5300) RAM. What I can't figure out is the maximum amount I can put in it, as I cannot find the manual anywhere online. I've found a few marketing broadsheets from online retailers that say, "up to 2 GB of RAM!" but I am not sure whether to believe them. They also do not seem to be quite for the same board, as they indicate DDR2 400/533 RAM, for example: http://www.geeks.com/details.asp?invtid=P4M8P-M7. The manufacturer's web site says the same thing, but does not elaborate. It's a 64-bit CPU and board; is there a technical reason why the board would not be able to address more than 2 GB? Can someone tell me what sort of that reason that would be? I bought this server from someone really hoping I could put 8 to 16 in it, and wanted to do some research before I gave up. On a related note, it's not indicated anywhere whether it can take ECC RAM; the existing chips are not ECC, but most memory sold in the range I'm looking for (e.g. DIMMs with enough chip density to do 8 GB) seems to be server-class and for that reason ECC. Any ideas? Thank you very much for your consideration in advance!

    Read the article

  • Hosting a javascript api file for third party sites the way sharethis, uservoice, analytics do it.

    - by Dayson
    I'm preparing to launch a service soon which will provide third party websites a widget. The widget requires my javascript file in the website's code. Exactly the same way services like analytics, uservoice, sharethis, getclicky, etc provide you with a javascript snippet to add to your page. Therefore, my javascript file is going to be hotlinked by tons of websites which possibly receive a lot of requests too. I need advice/opinions on the following aspects: What's the right location for hosting this file? Should I use a sub-domain for it? I was thinking of something like http://api.myservice.com/js/foo.js . Remember, once websites start embedding this file, its location CANNOT change under any circumstances. Right now we can afford just one dedicated server. So I have minified my file, enabled gzip and plan to use some good cache control headers through apache. Also, in the near future when the requests pickup, I will use a http proxy like Varnish. Is this a good plan for the near future? Should I be considering a CDN in the future (since we can't afford it now)? If so how do I make sure we're prepared to migrate to it without breaking services. Pros/Cons of moving just this file to a CDN? Also, since its just one javascript file(50kb), any affordable CDN so we could consider it in the beginning itself? Any other word of advice I could use? Anything I shouldn't overlook at this stage which I would regret later? (both in terms of server + javascript ajax limitations) Thanks in advance.

    Read the article

  • pure-ftpd not listening on specified port

    - by Jason McLaren
    I installed the pure-ftpd package (version 1.0.35-1) on an Ubuntu 12.04 box (an EC2 instance based on the standard Ubuntu 12.04 AMI). The pure-ftpd daemon is running (verified with ps), though there is no PID file (expected one to be created by the /etc/init.d/pure-ftpd script). Here's the resulting command that gets run by the init.d script: /usr/sbin/pure-ftpd -l pam -O clf:/var/log/pure-ftpd/transfer.log -o -8 UTF-8 -u 1000 -E -B -g /var/run/pure-ftpd/pure-ftpd.pid Here's my real problem: the ftp server isn't actually listening on any port (checked with netstat and nmap). So I can't ftp to the server (either locally using localhost or remotely using the public IP address). I tried adding a Bind file to /etc/pure-ftpd/conf and restarting, but it didn't help. When I installed pure-ftpd, it replaced inetd with openbsd-inetd, but did not run it since there were no services enabled. So inetd is not listening on port 21 either. (Apparently Ubuntu has a no-inetd-by-default policy, according to https://lists.ubuntu.com/archives/ubuntu-users/2010-September/227905.html .) I want to run pure-ftpd by itself (not with inetd) anyways, since the /etc/init.d/pure-ftpd script requires no inetd if you use the UploadScript feature. I'm not familiar with how Ubuntu handles network services (and can't find any relevant docs besides generic man pages), so I'm probably missing something obvious. Nothing seems out of the ordinary with /etc/hosts.allow (empty) or hosts.deny (empty), and I didn't add any firewall rules (iptables -L shows that the firewall is in its initial state). I've checked the pure-ftpd docs; not sure what else to look at. Any help would be appreciated, thanks!

    Read the article

  • Installing SQLServer 2005 on Windows 7 64bit

    - by Mostafa
    Hi , It's 3 days I'm trying to install SqlServer 2005 under Windows 7 64 bit on my computer. First let me tell you what I've done and what I've got till now . 1-I Installed Windows 7 64 Bit on my computer 2-I tried to install SQl Server 2005 "Developer Edition" 2.1 But in "System Configuration Check" Page i recieved 2 warning , One for "IIS Feature Requirement" and another for "ASP.NET Version Registration Rquired" . 2.1.1 . I installed "Internet Information Services" from "Turn Windows features on or off" section in control panel 2.1.2 I Enabled reporting service 32 bit from "Inetpub= AdminScripts = adsutil.vbs" 2.2 At this stage There was no waring in System Configuration Check 3- So I installed SQl Server 2005 Developer Edition By all default settings 4- I installed Sql Server 2005 Service Pack 3 64 bit Now when when i run "Management Studio" There is no name in "Server name" section . I typed my Computer name Or "." and i got this Error : A network -related instance-specific error occurred while establishinga connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (Provider: Named Pipes Provider , error :40 - Could not open a connection to SQL Server ) ( Microsoft SQL Server , Error :2) . I googled some for this Error and some people said follow this instruction: Startsql server 2005Configuration toolsSql Server Surface Configuration AreaSurface Area Configuration for services and Connections But i got this Error : No SQl SErver 2005 Components were found on the specified computer . Either no components are installed , or you are not a administrator on this computer (SQLSAC) I'm really tired because of that , and i don't know what's wrong with this . Some more information : I have no additonal software on my computer , like Antivirus or Proxy I tried all step with "Standard Edition" either , but no difference My user is Administrator I tried more than 5 times all those steps including re-installing Windows 7 . Please help me , I'm losing all my hair

    Read the article

  • remote telnet and email

    - by Mustafa Ismail Mustafa
    This issue has been occupying my work for the last few days and I will be understating when I say its driven me up the blasted walls. Essentially, I can ping and tracert the domain jnrcs.org and the subdomains mail.jnrcs.org and mail.jordanredcrescent.org. All three mentioned point to ip address 212.38.147.97. About 4 days ago, when we registered the domain "jnrcs.org" suddenly all external connection to the mail server from outside was lost. Not just mail, but other http based port-forwarded or natted services (such as camera surveillance and pbx services). I tried good old telnet (I'm a linux user) and I get the following output: telnet> o mail.jnrcs.org 25 Trying 212.38.147.97... telnet: Unable to connect to remote host: No route to host telnet> Tracert gives me: traceroute to mail.jnrcs.org (212.38.147.97), 30 hops max, 60 byte packets 1 192.168.1.2 (192.168.1.2) 0.869 ms 0.944 ms * 2 * * * 3 * * * 4 * * * 5 * * * 6 * 212.38.128.118 (212.38.128.118) 33.875 ms 39.187 ms 7 * * * 8 * * * 9 * * * 10 * * * 11 * * 212.38.147.97 (212.38.147.97) 67.621 ms I am stumped. Other friends from all around the world can telnet no problem. What could have possibly happened to make telnet/smtp/pop/imap/http access stop? Please bear in mind I'm primarily a developer but I [am under the delusion] that I can carry my weight in IT administration :) TIA

    Read the article

  • Finding out why Dell Controler is Degraded

    - by Kyle Brandt
    I installed open manage on a couple of my PE 2950s for snmp monitoring of the RAID. All the checks seem to come back okay except for controllerState: [root@aMachine ~]# snmpwalk -v 2c -c bestNotToPostPasswords myMachine -m +StorageManagement-MIB controllerstate StorageManagement-MIB::controllerState.1 = INTEGER: degraded(6) Other checks seems to indicate the battery, LD, and physicals disks are all good unless I missing something. Can anyone tell if I am missing something or neglecting something import in my RAID monitoring/understanding? I get degraded for both these servers I have set up. A walk of the entire storage management tree for on of them: StorageManagement-MIB::softwareVersion.0 = STRING: "3.2.0" StorageManagement-MIB::globalStatus.0 = INTEGER: warning(2) StorageManagement-MIB::softwareManufacturer.0 = STRING: "Dell Inc." StorageManagement-MIB::softwareProduct.0 = STRING: "Server Administrator (Storage Management)" StorageManagement-MIB::softwareDescription.0 = STRING: "Configuration and monitoring of disk storage devices." StorageManagement-MIB::displayName.0 = STRING: "Server Administrator (Storage Management)" StorageManagement-MIB::description.0 = STRING: "Configuration and monitoring of disk storage devices." StorageManagement-MIB::agentVendor.0 = STRING: "Dell Inc." StorageManagement-MIB::agentTimeStamp.0 = INTEGER: 1273842310 StorageManagement-MIB::agentGetTimeout.0 = INTEGER: 5 StorageManagement-MIB::agentModifiers.0 = INTEGER: 0 StorageManagement-MIB::agentRefreshRate.0 = INTEGER: 300 StorageManagement-MIB::agentMibVersion.0 = STRING: "3.2" StorageManagement-MIB::agentManagementSoftwareURLName.0 = "" StorageManagement-MIB::agentGlobalSystemStatus.0 = INTEGER: nonCritical(4) StorageManagement-MIB::agentLastGlobalSystemStatus.0 = INTEGER: ok(3) StorageManagement-MIB::agentSmartThermalShutdown.0 = INTEGER: notApplicable(3) StorageManagement-MIB::controllerNumber.1 = INTEGER: 1 StorageManagement-MIB::controllerName.1 = STRING: "PERC 5/i Integrated" StorageManagement-MIB::controllerVendor.1 = STRING: "DELL" StorageManagement-MIB::controllerType.1 = INTEGER: sas(6) StorageManagement-MIB::controllerState.1 = INTEGER: degraded(6) StorageManagement-MIB::controllerRebuildRateInPercent.1 = INTEGER: 30 StorageManagement-MIB::controllerFWVersion.1 = STRING: "5.0.2-0003" StorageManagement-MIB::controllerCacheSizeInMB.1 = INTEGER: 256 StorageManagement-MIB::controllerCacheSizeInBytes.1 = INTEGER: 0 StorageManagement-MIB::controllerPhysicalDeviceCount.1 = INTEGER: 5 StorageManagement-MIB::controllerLogicalDeviceCount.1 = INTEGER: 1 StorageManagement-MIB::controllerRollUpStatus.1 = INTEGER: nonCritical(4) StorageManagement-MIB::controllerComponentStatus.1 = INTEGER: nonCritical(4) StorageManagement-MIB::controllerNexusID.1 = STRING: "\\0" StorageManagement-MIB::controllerAlarmState.1 = INTEGER: disabled(2) StorageManagement-MIB::controllerDriverVersion.1 = STRING: "00.00.03.05 " StorageManagement-MIB::controllerPCISlot.1 = STRING: "embedded" StorageManagement-MIB::controllerClusterMode.1 = INTEGER: notApplicable(99) StorageManagement-MIB::controllerMinFWVersion.1 = STRING: "5.2.1-0067" StorageManagement-MIB::controllerMinDriverVersion.1 = STRING: "00.00.03.21" StorageManagement-MIB::controllerChannelCount.1 = INTEGER: 2 StorageManagement-MIB::controllerReconstructRate.1 = INTEGER: 30 StorageManagement-MIB::controllerPatrolReadRate.1 = INTEGER: 30 StorageManagement-MIB::controllerBGIRate.1 = INTEGER: 30 StorageManagement-MIB::controllerCheckConsistencyRate.1 = INTEGER: 30 StorageManagement-MIB::controllerPatrolReadMode.1 = INTEGER: automatic(1) StorageManagement-MIB::controllerPatrolReadState.1 = INTEGER: stopped(1) StorageManagement-MIB::controllerPatrolReadIterations.1 = INTEGER: 162 StorageManagement-MIB::controllerEntry.57.1 = INTEGER: 99 StorageManagement-MIB::controllerEntry.58.1 = INTEGER: 99 StorageManagement-MIB::channelNumber.1 = INTEGER: 1 StorageManagement-MIB::channelNumber.2 = INTEGER: 2 StorageManagement-MIB::channelName.1 = STRING: "Connector 0" StorageManagement-MIB::channelName.2 = STRING: "Connector 1" StorageManagement-MIB::channelState.1 = INTEGER: ready(1) StorageManagement-MIB::channelState.2 = INTEGER: ready(1) StorageManagement-MIB::channelRollUpStatus.1 = INTEGER: ok(3) StorageManagement-MIB::channelRollUpStatus.2 = INTEGER: ok(3) StorageManagement-MIB::channelComponentStatus.1 = INTEGER: ok(3) StorageManagement-MIB::channelComponentStatus.2 = INTEGER: ok(3) StorageManagement-MIB::channelNexusID.1 = STRING: "\\0\\0" StorageManagement-MIB::channelNexusID.2 = STRING: "\\0\\1" StorageManagement-MIB::channelBusType.1 = INTEGER: sas(8) StorageManagement-MIB::channelBusType.2 = INTEGER: sas(8) StorageManagement-MIB::enclosureNumber.1 = INTEGER: 1 StorageManagement-MIB::enclosureName.1 = STRING: "Backplane" StorageManagement-MIB::enclosureVendor.1 = STRING: "DELL" StorageManagement-MIB::enclosureState.1 = INTEGER: ready(1) StorageManagement-MIB::enclosureProductID.1 = STRING: "BACKPLANE " StorageManagement-MIB::enclosureType.1 = INTEGER: internal(1) StorageManagement-MIB::enclosureChannelNumber.1 = INTEGER: 0 StorageManagement-MIB::enclosureRollUpStatus.1 = INTEGER: ok(3) StorageManagement-MIB::enclosureComponentStatus.1 = INTEGER: ok(3) StorageManagement-MIB::enclosureNexusID.1 = STRING: "\\0\\0\\0" StorageManagement-MIB::enclosureFirmwareVersion.1 = STRING: "1.00" StorageManagement-MIB::enclosureSASAddress.1 = STRING: "50019090B4C67200" StorageManagement-MIB::arrayDiskNumber.1 = INTEGER: 1 StorageManagement-MIB::arrayDiskNumber.2 = INTEGER: 2 StorageManagement-MIB::arrayDiskNumber.3 = INTEGER: 3 StorageManagement-MIB::arrayDiskNumber.4 = INTEGER: 4 StorageManagement-MIB::arrayDiskName.1 = STRING: "Physical Disk 0:0:0" StorageManagement-MIB::arrayDiskName.2 = STRING: "Physical Disk 0:0:1" StorageManagement-MIB::arrayDiskName.3 = STRING: "Physical Disk 0:0:2" StorageManagement-MIB::arrayDiskName.4 = STRING: "Physical Disk 0:0:3" StorageManagement-MIB::arrayDiskVendor.1 = STRING: "DELL " StorageManagement-MIB::arrayDiskVendor.2 = STRING: "DELL " StorageManagement-MIB::arrayDiskVendor.3 = STRING: "DELL " StorageManagement-MIB::arrayDiskVendor.4 = STRING: "DELL " StorageManagement-MIB::arrayDiskState.1 = INTEGER: online(3) StorageManagement-MIB::arrayDiskState.2 = INTEGER: online(3) StorageManagement-MIB::arrayDiskState.3 = INTEGER: online(3) StorageManagement-MIB::arrayDiskState.4 = INTEGER: online(3) StorageManagement-MIB::arrayDiskProductID.1 = STRING: "ST3146755SS " StorageManagement-MIB::arrayDiskProductID.2 = STRING: "ST3146755SS " StorageManagement-MIB::arrayDiskProductID.3 = STRING: "ST3146755SS " StorageManagement-MIB::arrayDiskProductID.4 = STRING: "ST3146755SS " StorageManagement-MIB::arrayDiskSerialNo.1 = STRING: "3LN0LRL0 " StorageManagement-MIB::arrayDiskSerialNo.2 = STRING: "3LN0JYJS " StorageManagement-MIB::arrayDiskSerialNo.3 = STRING: "3LN0LR0V " StorageManagement-MIB::arrayDiskSerialNo.4 = STRING: "3LN0JH97 " StorageManagement-MIB::arrayDiskRevision.1 = STRING: "T106" StorageManagement-MIB::arrayDiskRevision.2 = STRING: "T106" StorageManagement-MIB::arrayDiskRevision.3 = STRING: "T106" StorageManagement-MIB::arrayDiskRevision.4 = STRING: "T106" StorageManagement-MIB::arrayDiskEnclosureID.1 = STRING: "0" StorageManagement-MIB::arrayDiskEnclosureID.2 = STRING: "0" StorageManagement-MIB::arrayDiskEnclosureID.3 = STRING: "0" StorageManagement-MIB::arrayDiskEnclosureID.4 = STRING: "0" StorageManagement-MIB::arrayDiskChannel.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskChannel.2 = INTEGER: 0 StorageManagement-MIB::arrayDiskChannel.3 = INTEGER: 0 StorageManagement-MIB::arrayDiskChannel.4 = INTEGER: 0 StorageManagement-MIB::arrayDiskLengthInMB.1 = INTEGER: 139392 StorageManagement-MIB::arrayDiskLengthInMB.2 = INTEGER: 139392 StorageManagement-MIB::arrayDiskLengthInMB.3 = INTEGER: 139392 StorageManagement-MIB::arrayDiskLengthInMB.4 = INTEGER: 139392 StorageManagement-MIB::arrayDiskLengthInBytes.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskLengthInBytes.2 = INTEGER: 0 StorageManagement-MIB::arrayDiskLengthInBytes.3 = INTEGER: 0 StorageManagement-MIB::arrayDiskLengthInBytes.4 = INTEGER: 0 StorageManagement-MIB::arrayDiskLargestContiguousFreeSpaceInMB.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskLargestContiguousFreeSpaceInMB.2 = INTEGER: 0 StorageManagement-MIB::arrayDiskLargestContiguousFreeSpaceInMB.3 = INTEGER: 0 StorageManagement-MIB::arrayDiskLargestContiguousFreeSpaceInMB.4 = INTEGER: 0 StorageManagement-MIB::arrayDiskLargestContiguousFreeSpaceInBytes.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskLargestContiguousFreeSpaceInBytes.2 = INTEGER: 0 StorageManagement-MIB::arrayDiskLargestContiguousFreeSpaceInBytes.3 = INTEGER: 0 StorageManagement-MIB::arrayDiskLargestContiguousFreeSpaceInBytes.4 = INTEGER: 0 StorageManagement-MIB::arrayDiskTargetID.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskTargetID.2 = INTEGER: 1 StorageManagement-MIB::arrayDiskTargetID.3 = INTEGER: 2 StorageManagement-MIB::arrayDiskTargetID.4 = INTEGER: 3 StorageManagement-MIB::arrayDiskLunID.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskLunID.2 = INTEGER: 0 StorageManagement-MIB::arrayDiskLunID.3 = INTEGER: 0 StorageManagement-MIB::arrayDiskLunID.4 = INTEGER: 0 StorageManagement-MIB::arrayDiskUsedSpaceInMB.1 = INTEGER: 139392 StorageManagement-MIB::arrayDiskUsedSpaceInMB.2 = INTEGER: 139392 StorageManagement-MIB::arrayDiskUsedSpaceInMB.3 = INTEGER: 139392 StorageManagement-MIB::arrayDiskUsedSpaceInMB.4 = INTEGER: 139392 StorageManagement-MIB::arrayDiskUsedSpaceInBytes.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskUsedSpaceInBytes.2 = INTEGER: 0 StorageManagement-MIB::arrayDiskUsedSpaceInBytes.3 = INTEGER: 0 StorageManagement-MIB::arrayDiskUsedSpaceInBytes.4 = INTEGER: 0 StorageManagement-MIB::arrayDiskFreeSpaceInMB.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskFreeSpaceInMB.2 = INTEGER: 0 StorageManagement-MIB::arrayDiskFreeSpaceInMB.3 = INTEGER: 0 StorageManagement-MIB::arrayDiskFreeSpaceInMB.4 = INTEGER: 0 StorageManagement-MIB::arrayDiskFreeSpaceInBytes.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskFreeSpaceInBytes.2 = INTEGER: 0 StorageManagement-MIB::arrayDiskFreeSpaceInBytes.3 = INTEGER: 0 StorageManagement-MIB::arrayDiskFreeSpaceInBytes.4 = INTEGER: 0 StorageManagement-MIB::arrayDiskBusType.1 = INTEGER: sas(8) StorageManagement-MIB::arrayDiskBusType.2 = INTEGER: sas(8) StorageManagement-MIB::arrayDiskBusType.3 = INTEGER: sas(8) StorageManagement-MIB::arrayDiskBusType.4 = INTEGER: sas(8) StorageManagement-MIB::arrayDiskSpareState.1 = INTEGER: notASpare(5) StorageManagement-MIB::arrayDiskSpareState.2 = INTEGER: notASpare(5) StorageManagement-MIB::arrayDiskSpareState.3 = INTEGER: notASpare(5) StorageManagement-MIB::arrayDiskSpareState.4 = INTEGER: notASpare(5) StorageManagement-MIB::arrayDiskRollUpStatus.1 = INTEGER: ok(3) StorageManagement-MIB::arrayDiskRollUpStatus.2 = INTEGER: ok(3) StorageManagement-MIB::arrayDiskRollUpStatus.3 = INTEGER: ok(3) StorageManagement-MIB::arrayDiskRollUpStatus.4 = INTEGER: ok(3) StorageManagement-MIB::arrayDiskComponentStatus.1 = INTEGER: ok(3) StorageManagement-MIB::arrayDiskComponentStatus.2 = INTEGER: ok(3) StorageManagement-MIB::arrayDiskComponentStatus.3 = INTEGER: ok(3) StorageManagement-MIB::arrayDiskComponentStatus.4 = INTEGER: ok(3) StorageManagement-MIB::arrayDiskNexusID.1 = STRING: "\\0\\0\\0\\0" StorageManagement-MIB::arrayDiskNexusID.2 = STRING: "\\0\\0\\0\\1" StorageManagement-MIB::arrayDiskNexusID.3 = STRING: "\\0\\0\\0\\2" StorageManagement-MIB::arrayDiskNexusID.4 = STRING: "\\0\\0\\0\\3" StorageManagement-MIB::arrayDiskPartNumber.1 = STRING: "SG0DR2381253172FLRL0A00 " StorageManagement-MIB::arrayDiskPartNumber.2 = STRING: "SG0DR2381253172FJYJSA00 " StorageManagement-MIB::arrayDiskPartNumber.3 = STRING: "SG0DR2381253172FLR0VA00 " StorageManagement-MIB::arrayDiskPartNumber.4 = STRING: "SG0DR2381253172FJH97A00 " StorageManagement-MIB::arrayDiskSASAddress.1 = STRING: "5000C50002380201" StorageManagement-MIB::arrayDiskSASAddress.2 = STRING: "5000C50002385B89" StorageManagement-MIB::arrayDiskSASAddress.3 = STRING: "5000C50002385AA9" StorageManagement-MIB::arrayDiskSASAddress.4 = STRING: "5000C500023841E1" StorageManagement-MIB::arrayDiskSmartAlertIndication.1 = INTEGER: no(1) StorageManagement-MIB::arrayDiskSmartAlertIndication.2 = INTEGER: no(1) StorageManagement-MIB::arrayDiskSmartAlertIndication.3 = INTEGER: no(1) StorageManagement-MIB::arrayDiskSmartAlertIndication.4 = INTEGER: no(1) StorageManagement-MIB::arrayDiskManufactureDay.1 = STRING: "07" StorageManagement-MIB::arrayDiskManufactureDay.2 = STRING: "07" StorageManagement-MIB::arrayDiskManufactureDay.3 = STRING: "07" StorageManagement-MIB::arrayDiskManufactureDay.4 = STRING: "07" StorageManagement-MIB::arrayDiskManufactureWeek.1 = STRING: "07" StorageManagement-MIB::arrayDiskManufactureWeek.2 = STRING: "07" StorageManagement-MIB::arrayDiskManufactureWeek.3 = STRING: "07" StorageManagement-MIB::arrayDiskManufactureWeek.4 = STRING: "07" StorageManagement-MIB::arrayDiskManufactureYear.1 = STRING: "2005" StorageManagement-MIB::arrayDiskManufactureYear.2 = STRING: "2005" StorageManagement-MIB::arrayDiskManufactureYear.3 = STRING: "2005" StorageManagement-MIB::arrayDiskManufactureYear.4 = STRING: "2005" StorageManagement-MIB::arrayDiskMediaType.1 = INTEGER: hdd(2) StorageManagement-MIB::arrayDiskMediaType.2 = INTEGER: hdd(2) StorageManagement-MIB::arrayDiskMediaType.3 = INTEGER: hdd(2) StorageManagement-MIB::arrayDiskMediaType.4 = INTEGER: hdd(2) StorageManagement-MIB::arrayDiskEntry.36.1 = INTEGER: 1 StorageManagement-MIB::arrayDiskEntry.36.2 = INTEGER: 1 StorageManagement-MIB::arrayDiskEntry.36.3 = INTEGER: 1 StorageManagement-MIB::arrayDiskEntry.36.4 = INTEGER: 1 StorageManagement-MIB::arrayDiskEntry.40.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskEntry.40.2 = INTEGER: 0 StorageManagement-MIB::arrayDiskEntry.40.3 = INTEGER: 0 StorageManagement-MIB::arrayDiskEntry.40.4 = INTEGER: 0 StorageManagement-MIB::arrayDiskEntry.41.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskEntry.41.2 = INTEGER: 0 StorageManagement-MIB::arrayDiskEntry.41.3 = INTEGER: 0 StorageManagement-MIB::arrayDiskEntry.41.4 = INTEGER: 0 StorageManagement-MIB::arrayDiskEnclosureConnectionNumber.1 = INTEGER: 1 StorageManagement-MIB::arrayDiskEnclosureConnectionNumber.2 = INTEGER: 2 StorageManagement-MIB::arrayDiskEnclosureConnectionNumber.3 = INTEGER: 3 StorageManagement-MIB::arrayDiskEnclosureConnectionNumber.4 = INTEGER: 4 StorageManagement-MIB::arrayDiskEnclosureConnectionArrayDiskName.1 = STRING: "Physical Disk 0:0:0" StorageManagement-MIB::arrayDiskEnclosureConnectionArrayDiskName.2 = STRING: "Physical Disk 0:0:1" StorageManagement-MIB::arrayDiskEnclosureConnectionArrayDiskName.3 = STRING: "Physical Disk 0:0:2" StorageManagement-MIB::arrayDiskEnclosureConnectionArrayDiskName.4 = STRING: "Physical Disk 0:0:3" StorageManagement-MIB::arrayDiskEnclosureConnectionArrayDiskNumber.1 = INTEGER: 1 StorageManagement-MIB::arrayDiskEnclosureConnectionArrayDiskNumber.2 = INTEGER: 2 StorageManagement-MIB::arrayDiskEnclosureConnectionArrayDiskNumber.3 = INTEGER: 3 StorageManagement-MIB::arrayDiskEnclosureConnectionArrayDiskNumber.4 = INTEGER: 4 StorageManagement-MIB::arrayDiskEnclosureConnectionEnclosureName.1 = STRING: "Backplane" StorageManagement-MIB::arrayDiskEnclosureConnectionEnclosureName.2 = STRING: "Backplane" StorageManagement-MIB::arrayDiskEnclosureConnectionEnclosureName.3 = STRING: "Backplane" StorageManagement-MIB::arrayDiskEnclosureConnectionEnclosureName.4 = STRING: "Backplane" StorageManagement-MIB::arrayDiskEnclosureConnectionEnclosureNumber.1 = INTEGER: 1 StorageManagement-MIB::arrayDiskEnclosureConnectionEnclosureNumber.2 = INTEGER: 1 StorageManagement-MIB::arrayDiskEnclosureConnectionEnclosureNumber.3 = INTEGER: 1 StorageManagement-MIB::arrayDiskEnclosureConnectionEnclosureNumber.4 = INTEGER: 1 StorageManagement-MIB::arrayDiskEnclosureConnectionControllerName.1 = STRING: "PERC 5/i Integrated" StorageManagement-MIB::arrayDiskEnclosureConnectionControllerName.2 = STRING: "PERC 5/i Integrated" StorageManagement-MIB::arrayDiskEnclosureConnectionControllerName.3 = STRING: "PERC 5/i Integrated" StorageManagement-MIB::arrayDiskEnclosureConnectionControllerName.4 = STRING: "PERC 5/i Integrated" StorageManagement-MIB::arrayDiskEnclosureConnectionControllerNumber.1 = INTEGER: 1 StorageManagement-MIB::arrayDiskEnclosureConnectionControllerNumber.2 = INTEGER: 1 StorageManagement-MIB::arrayDiskEnclosureConnectionControllerNumber.3 = INTEGER: 1 StorageManagement-MIB::arrayDiskEnclosureConnectionControllerNumber.4 = INTEGER: 1 StorageManagement-MIB::batteryNumber.1 = INTEGER: 1 StorageManagement-MIB::batteryName.1 = STRING: "Battery 0" StorageManagement-MIB::batteryVendor.1 = STRING: "DELL" StorageManagement-MIB::batteryState.1 = INTEGER: ready(1) StorageManagement-MIB::batteryRollUpStatus.1 = INTEGER: ok(3) StorageManagement-MIB::batteryComponentStatus.1 = INTEGER: ok(3) StorageManagement-MIB::batteryNexusID.1 = STRING: "\\0\\0" StorageManagement-MIB::batteryPredictedCapacity.1 = INTEGER: ready(2) StorageManagement-MIB::batteryNextLearnTime.1 = INTEGER: 21 StorageManagement-MIB::batteryLearnState.1 = INTEGER: idle(16) StorageManagement-MIB::batteryEntry.13.1 = INTEGER: 0 StorageManagement-MIB::batteryMaxLearnDelay.1 = INTEGER: 168 StorageManagement-MIB::batteryConnectionNumber.1 = INTEGER: 1 StorageManagement-MIB::batteryConnectionBatteryName.1 = STRING: "Battery 0" StorageManagement-MIB::batteryConnectionBatteryNumber.1 = INTEGER: 1 StorageManagement-MIB::batteryConnectionControllerName.1 = STRING: "PERC 5/i Integrated" StorageManagement-MIB::batteryConnectionControllerNumber.1 = INTEGER: 1 StorageManagement-MIB::virtualDiskNumber.1 = INTEGER: 1 StorageManagement-MIB::virtualDiskName.1 = STRING: "Virtual Disk 0" StorageManagement-MIB::virtualDiskDeviceName.1 = STRING: "/dev/sda" StorageManagement-MIB::virtualDiskState.1 = INTEGER: ready(1) StorageManagement-MIB::virtualDiskLengthInMB.1 = INTEGER: 278784 StorageManagement-MIB::virtualDiskLengthInBytes.1 = INTEGER: 0 StorageManagement-MIB::virtualDiskWritePolicy.1 = INTEGER: writeBack(3) StorageManagement-MIB::virtualDiskReadPolicy.1 = INTEGER: noReadAhead(5) StorageManagement-MIB::virtualDiskCachePolicy.1 = INTEGER: not-applicable(99) StorageManagement-MIB::virtualDiskLayout.1 = INTEGER: raid-10(10) StorageManagement-MIB::virtualDiskCurStripeSizeInMB.1 = INTEGER: 0 StorageManagement-MIB::virtualDiskCurStripeSizeInBytes.1 = INTEGER: 65536 StorageManagement-MIB::virtualDiskTargetID.1 = INTEGER: 0 StorageManagement-MIB::virtualDiskRollUpStatus.1 = INTEGER: ok(3) StorageManagement-MIB::virtualDiskComponentStatus.1 = INTEGER: ok(3) StorageManagement-MIB::virtualDiskNexusID.1 = STRING: "\\0\\0" StorageManagement-MIB::virtualDiskArrayDiskType.1 = INTEGER: sas(1) StorageManagement-MIB::virtualDiskEntry.23.1 = INTEGER: 2 StorageManagement-MIB::virtualDiskEntry.24.1 = INTEGER: 0 StorageManagement-MIB::arrayDiskLogicalConnectionNumber.1 = INTEGER: 1 StorageManagement-MIB::arrayDiskLogicalConnectionNumber.2 = INTEGER: 2 StorageManagement-MIB::arrayDiskLogicalConnectionNumber.3 = INTEGER: 3 StorageManagement-MIB::arrayDiskLogicalConnectionNumber.4 = INTEGER: 4 StorageManagement-MIB::arrayDiskLogicalConnectionArrayDiskName.1 = STRING: "Physical Disk 0:0:0" StorageManagement-MIB::arrayDiskLogicalConnectionArrayDiskName.2 = STRING: "Physical Disk 0:0:1" StorageManagement-MIB::arrayDiskLogicalConnectionArrayDiskName.3 = STRING: "Physical Disk 0:0:2" StorageManagement-MIB::arrayDiskLogicalConnectionArrayDiskName.4 = STRING: "Physical Disk 0:0:3" StorageManagement-MIB::arrayDiskLogicalConnectionArrayDiskNumber.1 = INTEGER: 1 StorageManagement-MIB::arrayDiskLogicalConnectionArrayDiskNumber.2 = INTEGER: 2 StorageManagement-MIB::arrayDiskLogicalConnectionArrayDiskNumber.3 = INTEGER: 3 StorageManagement-MIB::arrayDiskLogicalConnectionArrayDiskNumber.4 = INTEGER: 4 StorageManagement-MIB::arrayDiskLogicalConnectionVirtualDiskName.1 = STRING: "Virtual Disk 0" StorageManagement-MIB::arrayDiskLogicalConnectionVirtualDiskName.2 = STRING: "Virtual Disk 0" StorageManagement-MIB::arrayDiskLogicalConnectionVirtualDiskName.3 = STRING: "Virtual Disk 0" StorageManagement-MIB::arrayDiskLogicalConnectionVirtualDiskName.4 = STRING: "Virtual Disk 0" StorageManagement-MIB::arrayDiskLogicalConnectionVirtualDiskNumber.1 = INTEGER: 1 StorageManagement-MIB::arrayDiskLogicalConnectionVirtualDiskNumber.2 = INTEGER: 1 StorageManagement-MIB::arrayDiskLogicalConnectionVirtualDiskNumber.3 = INTEGER: 1 StorageManagement-MIB::arrayDiskLogicalConnectionVirtualDiskNumber.4 = INTEGER: 1

    Read the article

  • Windows 7 Apache Crashes on ANY request

    - by Dan
    I have XAMPP installed. I am running Windows 7. I have WordPress installed so that I may tweak it and test things locally before putting them 'live' on a remote server. I just installed BuddyPress. The installation was rather seamless. I activated the plugin and almost immediately, Apache crashed. I have Apache running as a service so it immediately restarted itself and was running BUT if I even so much as refresh the page (or create any other request), down it goes. Listed here is the error report as generated by Windows 7: Problem signature: Problem Event Name: APPCRASH Application Name: apache.exe Application Version: 2.2.4.0 Application Timestamp: 45ebef86 Fault Module Name: ZendOptimizer.dll Fault Module Version: 0.0.0.0 Fault Module Timestamp: 45ea8fee Exception Code: c0000005 Exception Offset: 0004dc22 OS Version: 6.1.7600.2.0.0.256.1 Locale ID: 1033 Additional Information 1: 1ec0 Additional Information 2: 1ec0fd70d07d060e5bfcf53c69ad1739 Additional Information 3: 2c48 Additional Information 4: 2c48940de5e7d1cb2e131ad6a0ca2feb Read our privacy statement online: http://go.microsoft.com/fwlink/?linkid=104288&clcid=0x0409 If the online privacy statement is not available, please read our privacy statement offline: C:\Windows\system32\en-US\erofflps.txt Help?

    Read the article

< Previous Page | 398 399 400 401 402 403 404 405 406 407 408 409  | Next Page >