Search Results

Search found 11240 results on 450 pages for 'partition boot sector'.

Page 403/450 | < Previous Page | 399 400 401 402 403 404 405 406 407 408 409 410  | Next Page >

• External HDD incorrectly detected as internal - how change to enable hot swap/eject?

  - by Sam

  Hi All, I have win 7 x64 Home Prem. The HDD is a seagate barracuda, 7200.7 ST3120827AS. 3.5", Serial: 3ms006n6, Firmware: 3.42 (no further updates) NexStar CX External case (drivers installed). I have three drives: WD320 with OS installed WD750 data storage (internal) seagate 120 (external) - connected via esata board connected to sata on motherboard (MSI p43 neo) Tried uninstalling HDD in device manager to no effect. Also the internal WD750 is detected as an external drive and win taskbar icon allows for it to be ejected (unlike the seagate). All drives are configured - Online, Simple, Basic, NTFS, Active, Primary Partition (except c drive). The seagate was previously used as a primary disk with XP operating system so I deleted the volume and created/reformatted (not quick). HDD is no longer "Active". But did not fix problem. Background Originally, I installed win 7 with the bios set to IDE and forgot to install the chipset drivers. Then I changed win 7 to install the AHCI drivers, changed the bios to AHCI and rebooted. Win 7 loaded drivers but WD HDD gave problems/crashed. I installed chipset drivers and latest intell storage matrix software thingie (in safe mode). Everything worked fine after that except for the problem of not corrrectly detecting the external drive] I have noticed that under the driver properties (and similarly in the registry) the two drives are configured differently (e.g. in driver details property capabilities for the WD the value is set to 0000006, CM_DEVCAP_REMOVABLE & EJECTSUPPORTED - whereas the seagate shows 0000080 & CM_DEVCAP_SURPRISEREMOVALOK). Any easy way to configure things? I tried physically swapping the sata connections on the mainboard without success So far I have found that a solution to my problem might be to perform some reg changes: http://superuser.com/questions/12955/how-do-i-remove-the-option-to-eject-sata-drives-from-the-windows-7-tray-icon

  Read the article

• Hardware issue, bsod with windows xp irq and strange messages with ubuntu

  - by JP Hellemons

  I have an old Acer T160 and it used to run Windows XP. But I keep getting random BSOD's. I keep seeing IRQ conflicts. I tried to run ubuntu, which runs and keeps running. But sometimes is not responding. Also there are these popups at ubuntu 12.04 that my network cable (which is onboard) is unplugged. But I have no cable in it! and have an usb dongle for wifi. which also seems unstable. have to (auto)reconnect sometimes. So my question is: is it my mobo, power supply or something else? FYI: I had an dvd-rw station which did not open properly, so unplugged the ata and power, als removed the second harddrive. now only have sata harddrive. also removed the extra video card (ati sapphire x1600 pro) so use only onboard video now and still have these issues. EDIT Update: will try with a new PSU (power supply unit of 400watt) the old (factory) one was 300watt. and will use a usb drive which has 12.04 ubuntu on it (made with unetbootin) to format everything and re-install ubuntu. (so also delete mbr partition) will update the day after tomorrow.

  Read the article

• How can I remove all drivers and other files related to a USB Mass Storage device?

  - by Bob

  I have a flash drive here that does not work on one OS on computer - let's call it the desktop Windows 7. It works fine on another computer - laptop Windows 7. It also works fine on Windows 8 on the same desktop computer. Other flash drives work fine under desktop Windows 7. So not a hardware issue, not a generic USB Mass Storage driver issue. It's something specific to this drive. On desktop Windows 7, I can connect the drive but no volume comes up under Windows Explorer. Ditto for Disk Management. With diskpart, loading hangs until I unplug the drive, if I replug it and try list disk it hangs again. If I unplug the drive at this point, list disk prints out all attached drives - including the just removed flash drive. The drive consistently appears under Device Manager, but uninstalling the drivers, restarting and reinstalling the drivers (by inserting the drive) only works for the first insertion. After that it fails again. I get the feeling that the driver files are not actually removed, and are corrupted, meaning every reinstall it's the same corrupted drivers being installed. Is there any way to remove these drivers completely? Or perhaps some other setting Windows 7 retains? Formatting the drive through another computer/OS does not help. I've also tried a complete wipe and rebuild of the MBR and single partition. The allocation unit size makes no difference; neither does a NTFS format. This is a relatively small matter, and I would not like to reinstall the entire OS!

  Read the article

• Windows 8 using as a webserver

  - by Jason

  I have a few hobby websites that I currently host on CentOS 6. Apache, mail serving, PHP, MySQL nothing special. In the past I used Windows XP to do this same task, for years, and I was OK. I switched to Linux and for the last few years it has been such a pain. updates break, certain apps only support certain distros without compiling from source. It prevents me from working on my hobby sites more because I am always fixing something. With Windows I locked it down, I run a hardware firewall and packet analyser, kept up on updates and A/V and never had a problem. I dont allow RDC from outside the local LAN, no FTP open, run OpenSSH on an obscure port.. I am considering switching to Windows 8 (since it is a cheaper license now that Windows 7) and running apache, HMailServer, PHP, MySQL, just like my CentOS install. My questions: I am not familiar with Windows 8, can the above be done like XP? No new security restrictions or the OS preventing this from happening? The machine is a Athlon 64-bit X2 with 32GB of RAM. Will Windows 8 see all of the RAM? Technically the machine came with Windows 7, and there is a serial number on it but I am sure I wiped away the Windows 7 recovery partition when I switched to Linux....

  Read the article

• kill a hung mount process

  - by John P

  I have a virtual machine drive that ran out of space, so I shutdown the VM, extended the volume using lvextend. After resizing the partition (ext3), I ran e2fsck on it, and it found and corrected errors. Unfortunately, when I ran efsck one more time, there were more errors that had to be fixed. I went through 3 rounds of e2fsck before I decided to try mounting it to clean up some space manually. I tried mounting it, but the mount process hung. I tried to "kill -9" the mount process, but that did not kill it. I killed the parent process, but that did not kill it either. Any ideas on how to kill a rogue mount process? Some evidence: ps -l 13292 F S UID PID PPID C PRI NI ADDR SZ WCHAN TTY TIME CMD 4 R 0 13292 1 99 85 0 - 17964 - ? 11:27 mount /dev/mapper/xen7-123p3 /tmp/p3/ lsof -p 13292 COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME mount 13292 root cwd DIR 9,2 4096 25264129 /root mount 13292 root rtd DIR 9,2 4096 2 / mount 13292 root txt REG 9,2 61656 2916434 /bin/mount mount 13292 root mem REG 9,2 144776 31457282 /lib64/ld-2.5.so mount 13292 root mem REG 9,2 1718232 31457284 /lib64/libc-2.5.so mount 13292 root mem REG 9,2 23360 31457291 /lib64/libdl-2.5.so mount 13292 root mem REG 9,2 43808 31457783 /lib64/libblkid.so.1.0 mount 13292 root mem REG 9,2 247496 31457331 /lib64/libsepol.so.1 mount 13292 root mem REG 9,2 95464 31457337 /lib64/libselinux.so.1 mount 13292 root mem REG 9,2 154640 31457491 /lib64/libdevmapper.so.1.02 mount 13292 root mem REG 9,2 17936 31457472 /lib64/libuuid.so.1.2 mount 13292 root mem REG 9,2 56438208 12684878 /usr/lib/locale/locale-archive mount 13292 root 0u CHR 136,11 0t0 13 /dev/pts/11 (deleted) mount 13292 root 1u CHR 136,11 0t0 13 /dev/pts/11 (deleted) mount 13292 root 2u CHR 136,11 0t0 13 /dev/pts/11 (deleted) umount -f /tmp/p3/ umount2: Invalid argument umount: /tmp/p3/: not mounted

  Read the article

• KVM Hosting: How to efficiently replicate guests

  - by javano

  I have three KVM servers each with 1 guest VM, running directly on it's local storage, (so they are essentially getting a dedicated box worth of computing power each). In the event of a host failure I would like the guests replicated to at least one of the other hosts so I can spin it up there, until the failing host is fixed. I am curious about KVM cloning. I can clone a VM live or when it's suspended/shutdown. Obivously suspended VMs will naturally be quicker to clone but these three VMs comprise three parts of a single solution, so I don't want to ever have any one of them shutdown. How can I efficiently clone these VMs between servers? I have had a couple of ideas, but are these insane or, is there a better method I have missed for my scenario? Set up a DRDB partition between box 1 and 2 where VM 1 runs from, and so is replicated between box1 and box 2, repeat between box 2 & 3, and box 3 & 1 (This could be insane, I have never used DRDB only read about it) Just use standard KVM CLI clone options to perform live clones (I'm dubious about this because I don't know how long it will take and what the performance impact will be during) Run a copy of each VM on at least one other host, and have the guest on one host export it's data to the matching guest on another host where it can import that data, scripting this on the guest) Some of other way? Ideas welcome! Side Note These servers have 4x15k SAS drives in a RAID 10 so they aren't rocketing fast, and as I mentioned, each VM runs from the host's local storage, no NAS or SAN etc. So that is why I am asking this question about guest replication. Also, this isn't about disaster recovery. Guests will be exporting their data to a NAS over a VPN, so I am looking at how I can have them quickly spun up in a host failure situation.

  Read the article

• Trouble getting started with the STEALTH monitoring package

  - by dlanced

  Is anyone here familiar with the Linux-based STEALTH package (for monitoring FS integrity of client systems)? I'm trying to get started with a very simple configuration, but I'm running into trouble (this is running under Ubuntu 14.04): Config line `USE BASE/root/stealth/10.0.0.79' invalid STEALTH (2.11.02) started at Fri, 30 May 2014 15:25:00 +0000 Program terminated due to non-zero exit value for -type f -exec /usr/bin/sha1sum {} \; (EOC Fri May 30 15:25:00 2014 127) Stealth is creating a binary tmp file in the Stealth server root and generating a "report" file in the start directory, but not much else. Regarding the "USE BASE...invalid" error, and just to be sure, I manually created the directories in /root, but it didn't help. And, by the way, I am running stealth with sudo. Everything seems to be configured correctly: I'm able to ssh into root@client from the stealth machine without a password Here's my "policy" file (I've removed the email directives just for simplicity): DEFINE SSHCMD /usr/bin/ssh [email protected] -T -q exec /bin/bash --noprofile DEFINE EXECSHA1 -xdev -perm +u+s,g+s ( -user root -or -group root ) \ -type f -exec /usr/bin/sha1sum {} \; USE BASE/root/stealth/10.0.0.79 USE SSH ${SSHCMD} USE DD /bin/dd USE DIFF /usr/bin/diff USE PIDFILE /var/run/stealth- USE REPORT report USE SH /bin/sh GET /usr/bin/sha1sum /root/tmp LABEL \nchecking the client's /usr/bin/find program CHECK LOG = remote/binfind /usr/bin/sha1sum /usr/bin/find LABEL \nsuid/sgid/executable files uid or gid root on the / partition CHECK LOG = remote/setuidgid /usr/bin/find / ${EXECSHA1} LABEL \nconfiguration files under /etc CHECK LOG = remote/etcfiles \ /usr/bin/find /etc -type f -not -perm /6111 \ -not -regex "/etc/(adjtime\|mtab)"\ -exec /usr/bin/sha1sum {} \; Any ideas? Thanks,

  Read the article

• problem transferring Win 7 operating system hard drive to be used as external hard drive

  - by itserich

  Win 7 Asus MA479 8GB Ram hard drives are 500GB The operating system was a Caviar Green, and I tried to exchange it for a Caviar Blue. The Caviar Blue took the install correctly, but the Green, the prior operating system hard drive, will not allow itself to be used as an external hard drive. I use TrueCrypt and tried to format the Green and it freezes each time at the very end of the encyrption of the partition. I took the Blue out of the system and tried to encrypt it, and same problem. I think there must be something on the hard drive that shows it was a system drive and it causes a conflict. I have tried writing over the system hard drive to fully erase everything but that does not work, it still freezes. The drives will work in a different pc, i.e. other pc where it never was the system drive. The external hard drive is connected esata through Thermaltake. I have used TrueCrypt on various pc's for years including this Win7 with no problem. Thank you.

  Read the article

• External HDD incorrectly detected as internal - how change to enable hot swap/eject?

  - by Sam

  I have win 7 x64 Home Prem. The HDD is a seagate barracuda, 7200.7 ST3120827AS. 3.5", Serial: 3ms006n6, Firmware: 3.42 (no further updates) NexStar CX External case (drivers installed). I have three drives: WD320 with OS installed WD750 data storage (internal) seagate 120 (external) - connected via esata board connected to sata on motherboard (MSI p43 neo) Tried uninstalling HDD in device manager to no effect. Also the internal WD750 is detected as an external drive and win taskbar icon allows for it to be ejected (unlike the seagate). All drives are configured - Online, Simple, Basic, NTFS, Active, Primary Partition (except c drive). The seagate was previously used as a primary disk with XP operating system so I deleted the volume and created/reformatted (not quick). HDD is no longer "Active". But did not fix problem. Background Originally, I installed win 7 with the bios set to IDE and forgot to install the chipset drivers. Then I changed win 7 to install the AHCI drivers, changed the bios to AHCI and rebooted. Win 7 loaded drivers but WD HDD gave problems/crashed. I installed chipset drivers and latest intell storage matrix software thingie (in safe mode). Everything worked fine after that except for the problem of not corrrectly detecting the external drive] I have noticed that under the driver properties (and similarly in the registry) the two drives are configured differently (e.g. in driver details property capabilities for the WD the value is set to 0000006, CM_DEVCAP_REMOVABLE & EJECTSUPPORTED - whereas the seagate shows 0000080 & CM_DEVCAP_SURPRISEREMOVALOK). Any easy way to configure things? I tried physically swapping the sata connections on the mainboard without success So far I have found that a solution to my problem might be to perform some reg changes: How do I remove the option to eject SATA drives from the Windows 7 tray icon?

  Read the article

• A very peculiar problem with an old pc and a newer laptop...

  - by user553492

  I got my old pc ( 248mb ram , 80 GB ) repaired and the tech people put XP in it .My newer laptop has UBUNTU 10.04 .now I only have one cable and one usb cord .So I connected my modem (with only one CAT5 port and 4 usb ports ) to laptop with CAT5 cable .Th internet is working fine . I also wanted to use net on older pc so I installed the usb drivers for win and it worked. But I got fed up of win xp and made a separate partition for FreeBSD which I planned to install .During the install I screwd up sumthing and now freebsd starts with a boot option with a ? mark in place of win xp .If I click on that it gives me a "NTLDR missing " msg. I tried connecting CAT5 cable between old and new pc and tried connecting my laptop with USB cable but nothing happend and then I realozed the modem doesnt have a WORKING usb driver for LINUX :( .FCUK ! .Freebsd doesnt` even detect the LAN cable if I use it for old pc . So basically I have a old pc that has FREEBSD which I can olny start and stare at the blank terminal console but works perfectly otherwise .FREEBSD was supposed to detect the LAN cable ??.And I have a laptop that has LINUX which only works if I connect it with a CAT5 cable .wtf . So what can I do with my old pc ??? any local server (if possible :( ) or some such thing ? or can u suggest any use .Im 18 and im into learning programming , coding .So I can practice it .Thankx !

  Read the article

• How can I add a second hard drive to a previously configured UEFI/ACHI Windows 8 machine?

  - by pflyer

  Recently purchased a new Windows 8 PC. It came with one hard drive. I want to a second hard drive to it. This second hard drive is my data hard drive from my previous computer. However, I have run into issues when the system accesses it. The drive is found in the BIOS. But is not seen by Explorer or Disk Management. I have added the drive to the next available SATA slot: SATA 2. The machine is a UEFI/ACHI based machine. In my reading I have found people documenting the following: 1) adding multiple partitioned hard drives (like mine is) to UEFI based machines is not possible 2) I have seen it suggested that you can only add blank hard drives to UEFI based machines. However, in doing so, I did not have success. I tried to add it as a hard drive with unallocated space and then as a hard drive with a single simple partition. Both attempts failed. My ultimate question: What is the proper procedure for adding a second hard drive to a UEFI/ACHI machine? I do not want to reinstall the OS and start from scratch as I have seen suggested elsewhere. There has to be a way to accomplish this without all that hassle. Thanks in advance for your help.

  Read the article

• FreeNAS pool configuration - RAID1 + other drives

  - by trnelson

  Simple questions, really. I found this answer with a similar setup, but not sure it answers my question. If it does, I'm curious why since the answer seems a bit unsure: ZFS Hard Drive Configuration in FreeNAS I'm building a server which will be used primarily for backup, plus some media streaming, possibly with Plex. I seem to understand most everything I need, but I'm still a bit confused on how pools work, and how to configure them for my scenario. I will have 2x 2TB WD Red drives, which I plan on using in a mirrored set up (RAID1). This would be for backup, and I'd also like to do offsite backup to my CrashPlan account from this array. I also have a few other drives: 1.5TB, 320GB, 250GB. I'm not sure exactly what to do with them yet, but looking for options. FreeNAS OS will be running from a 16GB USB Flash drive. Would it be wise to use the 1.5TB as a backup-backup, essentially as a mirror or perhaps for snapshots of the 2TB RAID1? I'm still learning about snapshots. Should the 2TB mirrored drives be in their own pool? Should the other drives be set up in their own pools as well, or should they be JBOD in a single pool? They may or may not get much use since the 2TB array is plenty for me. Does a dataset basically mimic the idea of a partition or a network share? In other words, I would map \SERVER\Share to X: on my laptop? Let's say I wanted to use the 250GB drive as an encrypted drive to store all of my cat pictures. Would it have to be in its own pool? If I use jails apps, should they go in the backup RAID1, or in another place? Thank you!

  Read the article

• Decrease in disk performance after partitioning and encryption, is this much of a drop normal?

  - by Biohazard

  I have a server that I only have remote access to. Earlier in the week I repartitioned the 2 disk raid as follows: Filesystem Size Used Avail Use% Mounted on /dev/mapper/sda1_crypt 363G 1.8G 343G 1% / tmpfs 2.0G 0 2.0G 0% /lib/init/rw udev 2.0G 140K 2.0G 1% /dev tmpfs 2.0G 0 2.0G 0% /dev/shm /dev/sda5 461M 26M 412M 6% /boot /dev/sda7 179G 8.6G 162G 6% /data The raid consists of 2 x 300gb SAS 15k disks. Prior to the changes I made, it was being used as a single unencrypted root parition and hdparm -t /dev/sda was giving readings around 240mb/s, which I still get if I do it now: /dev/sda: Timing buffered disk reads: 730 MB in 3.00 seconds = 243.06 MB/sec Since the repartition and encryption, I get the following on the separate partitions: Unencrypted /dev/sda7: /dev/sda7: Timing buffered disk reads: 540 MB in 3.00 seconds = 179.78 MB/sec Unencrypted /dev/sda5: /dev/sda5: Timing buffered disk reads: 476 MB in 2.55 seconds = 186.86 MB/sec Encrypted /dev/mapper/sda1_crypt: /dev/mapper/sda1_crypt: Timing buffered disk reads: 150 MB in 3.03 seconds = 49.54 MB/sec I expected a drop in performance on the encrypted partition, but not that much, but I didn't expect I would get a drop in performance on the other partitions at all. The other hardware in the server is: 2 x Quad Core Intel(R) Xeon(R) CPU E5405 @ 2.00GHz and 4gb RAM $ cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 32 Lun: 00 Vendor: DP Model: BACKPLANE Rev: 1.05 Type: Enclosure ANSI SCSI revision: 05 Host: scsi0 Channel: 02 Id: 00 Lun: 00 Vendor: DELL Model: PERC 6/i Rev: 1.11 Type: Direct-Access ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: CD-ROM GCR-8240N Rev: 1.10 Type: CD-ROM ANSI SCSI revision: 05 I'm guessing this means the server has a PERC 6/i RAID controller? The encryption was done with default settings during debian 6 installation. I can't recall the exact specifics and am not sure how I go about finding them? Thanks

  Read the article

• Drive letter not appearing after heat-related crash

  - by NickAldwin

  I recently had my old PC (has 3 physical hard drives partitioned into 6 partitions) off while on vacation. When I came back, I turned it on. I hadn't realized the room was warmer than it usually is due to hot weather while I was away. The computer was extremely slow to start up, then it crashed. When i rebooted, it got halfway through chkdsk on one of the non-system partitions, then crashed again. I opened it up and felt the hard drives and immediately shut down the computer and moved it to my basement to cool down because it was so hot. I left it there for a length of time while I reinstalled the A/C. I have now turned it on again. It is working fine, and every drive except for the one with the partition that was being checked has appeared in Windows. I scheduled chkdsk for all of the other partitions anyway, just in case, but I'm worried about that drive. I'm pretty sure the drive itself hasn't broken but that crashing in the middle of a chkdsk repair may have corrupted the data. What would you do in this situation? Most of the data on that drive was backed up, so it's not a huge deal if I lost it, but I'd like to get it back if I could. I also would love to regain usability of the drive, even if I have to wipe it -- but that's a last-resort sort of thing. What do you suggest I do?

  Read the article

• Is it a good Idea to switch to a SSD to use less battery?

  - by Walter Maier-Murdnelch

  I am thinking of buying a SSD for my laptop, mainly for the purpose of extended operating time when running on battery. At the moment I use a Hitachi HTS545032B9A300 (320GB) (Datasheet) as main drive and a Seagate Momentus 5400.3 120GB as secondary drive. I dualboot Windows and Linux but I don't need the windows partition any longer, a 120GB SDD would be more than sufficient space-wise. Speed is not an issue for me, I make heavy use of tmpfs (ramdrive) within Linux and transfers of bigger files are mainly through some network filesystem anyways, thus a cheaper SSD should do. For the purpose of comparison I chose the OCZ Vertex Plus 120GB. Power consumption always is a big promotional thing the industry uses to make me want to buy their SSDs, some sheet on the OCZ page provides an astonishing comparison of desktop HDDS and SSDs. The numbers I got comparing my laptop HDD and their SSD were not really astonishing any longer. Hitachi 320GB HDD: Startup (W, peak, max.) 4.5 Seek (W, avg.) 1.7 Read / Write (W, avg.) 1.4 Performance idle (W, avg.) 1.3 Active idle (W, avg.) 0.8 Low power idle (W, avg.) 0.5 Standby (W, avg.) 0.2 Sleep 0.1 OCZ 120GB SSD: 1.5W active 0.3W standby I see that there are differences, but actually they don't seem that high as I though they were. And compared to the power consuption of the rest of my system I wonder if it makes a difference at all. Have I just taken the wrong look at the whole thing or may I be better off to buy another battery for my laptop?

  Read the article

• Can't remove zfs log device from pool

  - by netmano

  I run a FreeBSD 9.0 server with ZFS pool version 28 and ZFS version 5. I had two pools with a log on ssd's two partitions. These pools was created on FreeBSD 8.2 with ZFS pool version 15, and ZFS version 4. After I upgraded to the new zfs version, I tried to remove the SSD log device from both pools both command was successful (no error message). One of the pools was the log removed, but the other still there, I down the server removed the ssd physically, and hoped it will be forgot by the zpool. The zpool became degraded as ssd was missing. I tied to remove again. No error message, but the log device entry still there. After it, to became the pool online again, I created a file on the root UFS partition and replaced the missing to device to this file. It was successful, the pool again online. However I can't remove the log device from the pool. Where can I have to look for error messages? (in dmesg there is nothing about it, also the zfs remove doesn't have any error message, it's seem like it was successful.

  Read the article

• How to tell Linux to explicitly swap out main memory of a suspended process?

  - by Vi

  I run a memory-hungry process (mkcromfs) which consumes more memory than I have physical memory on my latop, so it is paging and swappin and thrashing all the time and loadavg is about 2 (compcache is already in use with usual swap partition as well), but slowly moving forward (Although I afraid it will finally try to allocate 2GB and crash draining 2 days of thrashing). When I want to use the laptop for something else, I stop the process, start X server, firefox and other programs. The problem is that when I start Firefox the loadavg jumps to 10 and the system becomes almost unresponsive at all (long time to turn on/off caps lock, slow mouse cursor position updates, slow switching from X server to Linux console, slow login). The stopped mkcromfs still holds a lot of memory (464.8 MiB and slowly falling) and moves it to swap only when more memory is needed for some other program, which results in a great slowdown. How to tell the Linux to swap out this process entirely (e.g. I'm not intending to resume it in short term), possibly waking from swap other data? Also it will be useful to be able to specify the exact swap device to swap the given process out.

  Read the article

• Western Digital HDD now freezes my BIOS when loading the video card!

  - by Vercas

  After I have successively and successfully installed 3 Windows XP's on the same partition (Don't ask why...), I restarted my computer again and the BIOS just froze when it loaded the video card. Together with my uncle, we tracked down the problem and found out it's the HDD's fault. We tried booting without the HDD and it worked! (No other HDD (I have only one) but with a Ubuntu Live CD in.) We tried the HDD with a different data bus (It was from an identical computer) but that one didn't let my BIOS recognize the HDD. We also put the HDD in another computer as the second HDD and it DID recognize it but Windows XP kept saying it cannot install a driver and that it installed successfully. Happily, I have managed to backup some of my most important files in that other computer. The following is a list of tests that we have run. With the HDD Original data bus Original computer Result: BIOS freezes WITHOUT the HDD Original data bus Original computer Result: Everything works just fine! With the HDD ANOTHER data bus Original computer Result: Cannot see the HDD With the HDD Original data bus ANOTHER computer Result: It worked! With the HDD ANOTHER data bus ANOTHER computer Result: It worked! During the tests, we had only two data buses and two computers. (each data bus from it's own computer) Strange thing is that the second data bus cannot let the BIOS see the HDD in my computer but works just fine with the other computer. I beg you to help me! I have my most important data on that HDD and I really cannot afford to buy another decent IDE HDD now!

  Read the article

• What diagnostics are safe to run on an SSD drive?

  - by Peter Mounce

  I have a MacBook Pro (late 2010) with a Crucial RealSSD 256Gb in it; 60Gb is given to the Windows 7 x64 BootCamp partition. I have a USB-attached 500Gb drive for (most) data. In the last day or so, I've had a BSOD and several OS freezes (both Mac OSX 10.6.6 and Win7). The system in both cases will boot fine (at the moment!) and then run things fine, then some time later a program will stop responding, followed shortly thereafter by the system as a whole, forcing a reboot. This smacks to me of a storage problem. Given that I have an SSD and not a regular magnetic HDD, what are my next steps, in both OS'? I haven't seen anything pertinent in Windows' event-log. I'm not sure of the equivalent place to look in OSX; it's never given me issue to find out. What are my options for attempting to save my data from the SSD to another drive, given that after some small amount of time (eg half an hour), the OS stops responding? What are the recommended next steps?

  Read the article

• Kickstarting an Ubuntu Server 10.04 installation (DHCP fails)

  - by William

  I'm trying to automate the network installation of Ubuntu 10.04 LTS with an anaconda kickstart and everything seems to running except for the initial DHCP autoconfiguration. The installer attempts to configure the install via DHCP but fails on its first attempt. This brings me to a prompt where I can retry DHCP and it seems to always work on the second attempt. My issue is that this is not really automated if I have to hit retry for DHCP. Is there something I can add to the kickstart file so that it will automatically retry or better yet not fail the first time? Thanks. Kickstart: # System language lang en_US # Language modules to install langsupport en_US # System keyboard keyboard us # System mouse mouse # System timezone timezone America/New_York # Root password rootpw --iscrypted $1$unrsWyF2$B0W.k2h1roBSSFmUDsW0r/ # Initial user user --disabled # Reboot after installation reboot # Use text mode install text # Install OS instead of upgrade install # Use Web installation url --url=http://10.16.0.1/cobbler/ks_mirror/ubuntu-10.04-x86_64/ # System bootloader configuration bootloader --location=mbr # Clear the Master Boot Record zerombr yes # Partition clearing information clearpart --all --initlabel # Disk partitioning information part swap --size 512 part / --fstype ext3 --size 1 --grow # System authorization infomation auth --useshadow --enablemd5 %include /tmp/pre_install_ubuntu_network_config # Always install the server kernel. preseed --owner d-i base-installer/kernel/override-image string linux-server # Install the Ubuntu Server seed. preseed --owner tasksel tasksel/force-tasks string server # Firewall configuration firewall --disabled # Do not configure the X Window System skipx %pre wget "http://10.16.0.1/cblr/svc/op/trig/mode/pre/system/Test-D" -O /dev/null # Network information # Start pre_install_network_config generated code # Start of code to match cobbler system interfaces to physical interfaces by their mac addresses # Start eth0 # Configuring eth0 (00:1A:64:36:B1:C8) if ip -o link show | grep -i 00:1A:64:36:B1:C8 then IFNAME=$(ip -o link show | grep -i 00:1A:64:36:B1:C8 | cut -d" " -f2 | tr -d :) echo "network --device=$IFNAME --bootproto=dhcp" >> /tmp/pre_install_ubuntu_network_config fi # End pre_install_network_config generated code %packages openssh-server

  Read the article

• ASUS laptop doesn't charge/use the battery after reinstalling Windows 7

  - by Stan

  I've done a clean install of Windows 7 x64 on an ASUS X501A laptop. The battery is detected and shows in the system tray as "plugged in, charging". However the charge level stays at 76% and if the AC cord is plugged out the laptop turns off. The laptop does not turn on without being plugged in either. Everything worked perfectly prior to reinstall. I've tried: Downloading and installing all the ASUS drivers, including the ATK ACPI driver Checking the BIOS - there do not seem to be any battery-related settings Flashing the BIOS to the latest version Uninstalling Microsoft ACPI-Compliant Control Method Battery in device manager as suggested on the internet Full power discharge/ATX reset as suggested by ASUS support: remove mains power charger, remove battery, press and hold power button for 10 seconds, reconnect battery and mains and turn on I have a feeling all this may have something to do with the EFI BIOS that comes on the laptop. During the reinstall I had to delete all partitions and start anew, because the Windows installer complained about the improper order of GPT partitions. The EFI System Partition was recreated by the installer, and I am guessing that it may be missing the particular ACPI driver needed to make the battery work. I've tried researching this, but could not come up with any useful info. I am hoping someone here may know a bit more about this and maybe help me understand what's going on and how to fix it. Barring that, I'll have to re-image the drive off an identical ASUS laptop with stock install and hope it fixes things.

  Read the article

• 750Gig Hard Drive shows full with only 315Gigs used

  - by Chris Kelly

  I have a Win7 laptop with a 750Gig C: drive. It came partitioned with 714Gig usable from manufacturer. I installed programs, music files, etc up to 285 gigs. As of a few weeks ago it showed 285 Gigs. Two weeks of house guests later and it shows HD is full. I deleted some files but it still shows 652 Gigs on this drive while there are only 285 Gigs on drive. Relevant details: I am Administrator on laptop and have fair knowledge of what I am doing. I did not restore from backup, restore from mirror, upgrade HD's or anything else that would have touched the partition structure. Just daily use as imaging machine and web. I have checked partitions under disk administrator - no change, still partitioned with 714Gigs usable. Have looked through computer C drive by hand showing Hidden files and folders - no change. I have used JDisk Report to double check - it shows I have only 285 Gigs on C drive. I triple checked with TreeSize run as Administrator and it also shows 285 Gigs on C drive - yet Windows 7 still shows almost full. I used Windows 7 Utilities to Check for Disk Errors, and Defragged the drive. No errors shown and no change after Defrag.

  Read the article

• Ubuntu inside VirtualBox is slow

  - by Kapsh

  I am running an Ubuntu instance on VirtualBox inside XP. Here are the details: Host: Windows XP Pro Guest: Ubuntu 8.10 Total RAM: 3GB RAM For VM: 1GB Total Video Memory: 128MB Video Memory for VM: 40MB Hard Drive: 200GB Hard Drive for VM: 30GB Processor: 2.80GHz Core Duo The problem is that whenever I am inside the virtual machine, things seem so much slower in general. For example Firefox, Eclipse take longer to load, dragging windows show a lag etc. I have tried running Ubuntu before (not inside a VM) and it seemed fantastically fast. So I am disappointed to have to deal with this situation. But I need access to the XP partition without having to reboot and hence the attempt. I am surprised with the perceived slowness since the whole world seems to be doing virtualization and I cannot imagine everyone works on slow systems knowingly. My question is - is there something I should be doing to boost performance? Am I doing something wrong? This is my home machine and I am not sure if this is the right forum to ask. Thanks.

  Read the article

• Cannot install windows. Compaq Presario CQ62

  - by Matthew

  I bought a used Compaq Presario CQ62 for cheap, and went to install windows on it. I formatted the partition and went to install when I got this error.... Windows cannot install required files. The file may be corrupt or missing. Make sure all files required for installation are available and restart the installation. Error code: 0x80070017 I have used this disk before with no problems, but internet searching suggested I burn one at 2x speed because that helps for some reason... I'm burning one now, but my question is, why would I get this error, OTHER than the disc being bad? I'm pretty certain this one isn't as I have used it before... (ok so the slowly burned cd (using imgburn) didn't work either so it's DEFINITELY not the disc) Thanks in advanced for any answers Also I took one stick of ram out because internet searching also suggested that, but it didn't make a difference. Also I ran memory and hard drive checks and they passed fine. Also I reset the motherboard options to default What could it be!? Help I'm completely stumped...

  Read the article

• What does it mean to install two OS's alongside each other?

  - by Josh

  I currently have Windows 7 installed on my PC. However, I just tried out Ubuntu via booting from a disc and I love it. I want to install it onto my HDD, but I don't want to get rid of Windows 7. I know HOW to do this, but I am a little unsure what the consequences might be. What does it mean to install Ubuntu alongside Windows? Do they share the same resources? Also, I have my HDD already partitioned into two sections, a 70 GB section where Windows is installed and then another 400 GB section where all my data is stored. There is currently 26 GB free on the 70GB partition. I know Ubuntu doesn't take up much space. However, if I install Ubuntu in that space, will I still be able to install programs on Windows in the future? My main concern is that I am going to short-change my hard drive space for future installations. EDIT: I guess another big question I have is if I install a program on one OS, will the other be able to use it?

  Read the article

< Previous Page | 399 400 401 402 403 404 405 406 407 408 409 410  | Next Page >