Search Results

Search found 18364 results on 735 pages for 'nova network'.

Page 404/735 | < Previous Page | 400 401 402 403 404 405 406 407 408 409 410 411  | Next Page >

• Why do ICMP Redirct Host happen?

  - by El Barto

  I'm setting up a Debian box as a router for 4 subnets. For that I have defined 4 virtual interfaces on the NIC where the LAN is connected (eth1). eth1 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.1.1 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::960c:6dff:fe82:d98/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6026521 errors:0 dropped:0 overruns:0 frame:0 TX packets:35331299 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:673201397 (642.0 MiB) TX bytes:177276932 (169.0 MiB) Interrupt:19 Base address:0x6000 eth1:0 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.2.1 Bcast:10.1.2.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth1:1 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.3.1 Bcast:10.1.3.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth1:2 Link encap:Ethernet HWaddr 94:0c:6d:82:0d:98 inet addr:10.1.4.1 Bcast:10.1.4.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Base address:0x6000 eth2 Link encap:Ethernet HWaddr 6c:f0:49:a4:47:38 inet addr:192.168.1.10 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6ef0:49ff:fea4:4738/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:199809345 errors:0 dropped:0 overruns:0 frame:0 TX packets:158362936 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:3656983762 (3.4 GiB) TX bytes:1715848473 (1.5 GiB) Interrupt:27 eth3 Link encap:Ethernet HWaddr 94:0c:6d:82:c8:72 inet addr:192.168.2.5 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::960c:6dff:fe82:c872/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:110814 errors:0 dropped:0 overruns:0 frame:0 TX packets:73386 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:16044901 (15.3 MiB) TX bytes:42125647 (40.1 MiB) Interrupt:20 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:22351 errors:0 dropped:0 overruns:0 frame:0 TX packets:22351 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2625143 (2.5 MiB) TX bytes:2625143 (2.5 MiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:41358924 errors:0 dropped:0 overruns:0 frame:0 TX packets:23116350 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:3065505744 (2.8 GiB) TX bytes:1324358330 (1.2 GiB) I have two other computers connected to this network. One has IP 10.1.1.12 (subnet mask 255.255.255.0) and the other one 10.1.2.20 (subnet mask 255.255.255.0). I want to be able to reach 10.1.1.12 from 10.1.2.20. Since packet forwarding is enabled in the router and the policy of the FORWARD chain is ACCEPT (and there are no other rules), I understand that there should be no problem to ping from 10.1.2.20 to 10.1.1.12 going through the router. However, this is what I get: $ ping -c15 10.1.1.12 PING 10.1.1.12 (10.1.1.12): 56 data bytes Request timeout for icmp_seq 0 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 81d4 0 0000 3f 01 e2b3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 1 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 899b 0 0000 3f 01 daec 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 2 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 78fe 0 0000 3f 01 eb89 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 3 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 14b8 0 0000 3f 01 4fd0 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 4 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 8ef7 0 0000 3f 01 d590 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 5 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 ec9d 0 0000 3f 01 77ea 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 6 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 70e6 0 0000 3f 01 f3a1 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 7 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 b0d2 0 0000 3f 01 b3b5 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 8 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 f8b4 0 0000 3f 01 6bd3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 9 Request timeout for icmp_seq 10 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 1c95 0 0000 3f 01 47f3 10.1.2.20 10.1.1.12 Request timeout for icmp_seq 11 Request timeout for icmp_seq 12 Request timeout for icmp_seq 13 92 bytes from router2.mydomain.com (10.1.2.1): Redirect Host(New addr: 10.1.1.12) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 62bc 0 0000 3f 01 01cc 10.1.2.20 10.1.1.12 Why does this happen? From what I've read the Redirect Host response has something to do with the fact that the two hosts are in the same network and there being a shorter route (or so I understood). They are in fact in the same physical network, but why would there be a better route if they are not on the same subnet (they can't see each other)? What am I missing? Some extra info you might want to see: # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.8.0.2 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 127.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 lo 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth3 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 192.168.1.0 0.0.0.0 255.255.255.0 U 1 0 0 eth2 10.1.4.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 10.1.3.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth2 0.0.0.0 192.168.2.1 0.0.0.0 UG 100 0 0 eth3 # iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination # iptables -L -n -t nat Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- !10.0.0.0/8 10.0.0.0/8 MASQUERADE all -- 10.0.0.0/8 !10.0.0.0/8 Chain OUTPUT (policy ACCEPT) target prot opt source destination

  Read the article

• Setting up dual NICs under Server 2008

  - by Randall Sexton

  Hi, I'm trying to determine how to set up dual NICs on my Server 2008 box (not R2). I want all web traffic on one NIC and all Hyper-V traffic on the other. Is this possible? ( I assume that it is ) How is this done? ( A link to a tutorial you know of would be great ) Both NICs are the same (Intel PRO/1000 EB Network Connection with I/O Acceleration). Thanks in advance, Randall

  Read the article

• Ubuntu Server Port Forwarding the easy way?

  - by Arthur Ulfeldt

  I have an Ubuntu server (10.04) running nat and I understand how to forward ports using iptables which works fine and is only mildly painful. What is "the easy way" of doing this? Is there some nice wiz-bang-network-tool (like ufw) that makes simple port forwarding super simple.

  Read the article

• Only one sharepoint site is not reachable

  - by Kabir Rao

  We are facing a strange issue since morning...only one sharepoint site is not accessible. In our sharepoint 2003 server there are several sites configured for separate projects. Several IIS Reset has been done, everyother site is accesible except one. When I try to map the site as network drive, i am able to access the contents of site. Please help asap. Thanks upfront.

  Read the article

• Joining computers to domain when SBS is running in Datacenter

  - by ChrisMuench

  We are contemplating moving our SBS2k8 server to our datacenter. We would be setting up a VPN-VPN tunnel between everything to handle AD. Has anyone done this before? Any particular issues that anyone can remember? So the flow for AD would now become. SBS<-VPN---VPN<-Internal office network

  Read the article

• udp expected behaviour not responding to test result

  - by ernst

  I have a local network topology that is structured as follows: three hosts and a switch in the middle. I am using a switch that supports 10,100,1000 Mbit/s full/half duplex connection. I have configured the hosts with a static ip 172.16.0.1-2-3/25. This is the output of ifconfig eth0 Link encap: Ethernet HWaddr ***** inet addr:172.16.0.3 Bcast:172.16.0.127 Mask:255.255.255.128 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 The output on H1 and H2 is perfectly matchable They are mutually reachable since i have tested the network with ping. I have forced the ethernet interface to work at 10M with ethtool -s eth0 speed 10 duplex full autoneg on this is the output of ethtool eth0 supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full S upported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10baseT/Full Advertised pause frame use: Symmetric A dvertised auto-negotiation: Yes Speed: 10Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on MDI-X: Unknown Supports Wake-on: g Wake-on: d Current message level: 0x000000ff (255) drv probe link timer ifdown ifup rx_err tx_err Link detected: yes – I am doing an experimental test using nttcp to calculate the GOODPUT in the case that H1 and H2 at the same time send data to H3. Since the three links have the same forced capability and the amount of arrving data speed is 10 from H1+10 from H2--20M to H3 it would be expected a bottleneck effect and, due to the non reliable nature of udp, a packet loss. But this doesn't appen since the output of nttcp application shows the same number of byte sended and received. this is the output of nttcp on h3 nttcp -T -r -u 172.16.0.2 & nttcp -T -r -u 172.16.0.1 [1] 4071 Bytes Real s CPU s Real-MBit/s CPU-MBit/s Calls Real-C/s CPU-C/s l 8388608 13.74 0.05 4.8848 1398.0140 2049 149.14 42684.8 Bytes Real s CPU s Real-MBit/s CPU-MBit/s Calls Real-C/s CPU-C/s l 8388608 14.02 0.05 4.7872 1398.0140 2049 146.17 42684.8 1 8388608 13.56 0.06 4.9500 1118.4065 2051 151.28 34181.1 1 8388608 13.89 0.06 4.8310 1198.3084 2051 147.65 36623.0 – How is this possible? Am i missing something? Any help will be gratefully apprecciated, Best regards

  Read the article

• OpenOffice.org 3 waits 25 seconds before opening

  - by Joey Adams

  I'm on Fedora 14, and OpenOffice 3.3.0 takes a long time to open (about 30 seconds, sometimes less). It isn't a CPU or disk performance issue, it's just simply a very long delay before the program opens. It appears to be a frivolous network connection timing out. According to Wireshark, it tries to look up: dulcimer.(none) which fails, after which it tries to look up: dulcimer.(none).mylitestream.com (dulcimer is my hostname, and LiteStream is my ISP) Is there a way to work around this bug in OpenOffice?

  Read the article

• Is my Cisco switch port bad?

  - by ewwhite

  I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced last week, however the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link (switchport configuration pastebin). We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

  Read the article

• Web Farm Framework - Adding servers are offline

  - by Johan Wikström

  My problem is that im trying to setup a server farm but the nodes all come up as offline. I dont get a connection error saying that the servername is wrong, but get "offline" after it "test connection" I have: - Setup firewalls rules to allow Remote and file share on Domain and private network - Installed WWF 2.0 on both servers - Account that im using is a domain account that is Administrator on both machines. www01 is the same server as the controller below, but same results if i try www02 as primary. Any ideas?

  Read the article

• Which free VNC server works well with Windows 7 and how to advertise it via Samba for control by a M

  - by GJ

  Hi I need to control a Windows 7 PC via VNC from a Mac in an office LAN. Since the IPs are dynamically assigned, I'd like the PC to appear in my "Places" and in the automatically detected nearby servers in VNC client I'm using -- both of which require the PC to advertise its VNC server via Samba (right?). I tried installing ultravnc, which works when I access it directly by IP, but it doesn't seem to advertise itself in the network. Any ideas?

  Read the article

• Software to create diagrams in OS X

  - by Michael

  Something similar to Concept Draw under windows. Creating network, software, project architecture diagrams, flow charts, mind maps... All this for Snow Leopard.

  Read the article

• Windows File Server -- Where To Start

  - by yodie

  I have a Windows 2003 server, a whole load of PDFs on it that need to be accessed from various computers, both on the local network and not, and including mobile devices, and files that have to be sent to it. Where do I start? The most important thing (after getting the job done) is security.

  Read the article

• Connect Ubuntu 11.04 to xbox 360

  - by mrK

  I'd like to be able to stream .avi files to my xbox 360 video library. I've gone through a bunch of different servers (ushare, xbmc) both from the aptitude and from source. It seems that I can get the servers working from both localhost and from another computer on the network. However, the xbox cannot detect any of these. Can anybody give me a hand or perhaps post a detailed walkthrough to give me a hand? Thanks!

  Read the article

• How do get Ubuntu to stop modifying /etc/resolv.conf

  - by Neil

  I want to manually set my resolv.conf and have Ubuntu not automatically change it later. How do I get Ubuntu to stop modifying resolv.conf? I have already set "Automatic (DHCP) addresses only" in the network settings here:

  Read the article

• Send HD video over SONET

  - by Fizzy

  In an effort to test our new OC 192 network, we would like to find a way to stream HD video over it for a demonstration. We are looking for a device or combination of devices that connects to HDMI on one side and has a XFP client interface on the other. I understand this is a ridiculous request and we are planning on an "interesting" solution.

  Read the article

• Windows XP Home Edition SP3 WiFi WPA2 not working

  - by karthik

  My netbook OS is Windows XP Home Edition SP3. My wireless network option shows WPA/WPA2 option when I select it, it connects to the router but no internet access. Then I changed my router settings to WEP and configured my netbook and it works fine. I want to use WPA2 security. Please could anyone help to fix this issue?

  Read the article

• Mercurial simultaneous access

  - by mizipzor

  We have a mercurial repository (the stable branch) on a mapped network drive (windows). I want to know what happens if more than one user attempts to push at the same time. Or if someone pulls while another is halfway through a push. Is the mercurial client notified by the OS that the file is in use by another process and bails? Is there a risk that I could corrupt the repository with this setup?

  Read the article

• How do I see the negotiated wireless speed in Windows 7 and OS X

  - by user26453

  In Windows XP when I connected to a network it would list the speed at which I connected, e.g. 54 mbps, 11 mbps, etc. Where can I see the same information in in either Windows 7 or OS X? Since upgrading from XP I cannot see this info in Windows 7 and I've never been able to see it in OS X.

  Read the article

• Wakeup on LAN script works from Mac, but not Windows 7

  - by illyich

  I have a Linux server on my local network that is set up to use wakeup on lan. I copied this script verbatim, just replacing the MAC address in the example use. When I run this script on a Mac, the server wakes up. When I run it from Windows 7 (32-bit Ultimate) it doesn't do anything (note that the script DOES run, I added a debug raw_input() to confirm).

  Read the article

• PCMCIA Does Not Work on Dell Latitude under Windows XP

  - by Rich

  PCMCIA cards do not work on Dell Latitude e5510 under Windows XP. Works fine on Windows 7. Cards are recognized by Device Manager but do not work correctly. For example, CF adapter does not recognize when a card is inserted and network card is unable to obtain an IP address. Other systems that may be affected: Latitude E4310 Latitude E5410 Latitude E5510 Latitude E6410 Latitude E6410 ATG Latitude E6510 Dell Precision Mobile WorkStation M4500

  Read the article

• Postfix flow/hook reference, or high-level overview?

  - by threecheeseopera

  The Postfix MTA consists of several components/services that work together to perform the different stages of delivery and receipt of mail; these include the smtp daemon, the pickup and cleanup processes, the queue manager, the smtp service, pipe/spawn/virtual/rewrite ... and others (including the possibility of custom components). Postfix also provides several types of hooks that allow it to integrate with external software, such as policy servers, filters, bounce handlers, loggers, and authentication mechanisms; these hooks can be connected to different components/stages of the delivery process, and can communicate via (at least) IPC, network, database, several types of flat files, or a predefined protocol (e.g. milter). An old and very limited example of this is shown at this page. My question: Does anyone have access to a resource that describes these hooks, the components/delivery stages that the hook can interact with, and the supported communication methods? Or, more likely, documentation of the various Postfix components and the hooks/methods that they support? For example: Given the requirement "if the recipient primary MX server matches 'shadysmtpd', check the recipient address against a list; if there is a match, terminate the SMTP connection without notice". My software would need to 1) integrate into the proper part of the SMTP process, 2) use some method to perform the address check (TCP map server? regular expressions? mysql?), and 3) implement the required action (connection termination). Additionally, there will probably be several methods to accomplish this, and another requirement would be to find that which best fits (ex: a network server might be faster than a flat-file lookup; or, if a large volume of mail might be affected by this check, it should be performed as early in the mail process as possible). Real-world example: The apolicy policy server (performs checks on addresses according to user-defined rules) is designed as a standalone TCP server that hooks into Postfix inside the smtpd component via the directive 'check_policy_service inet:127.0.0.1:10001' in the 'smtpd_client_restrictions' configuration option. This means that, when Postfix first receives an item of mail to be delivered, it will create a TCP connection to the policy server address:port for the purpose of determining if the client is allowed to send mail from this server (in addition to whatever other restrictions / restriction lookup methods are defined in that option); the proper action will be taken based on the server's response. Notes: 1)The Postfix architecture page describes some of this information in ascii art; what I am hoping for is distilled, condensed, reference material. 2) Please correct me if I am wrong on any level; there is a mountain of material, and I am just one man ;) Thanks!

  Read the article

• mysql-proxy got error which cause it to crash

  - by nonus25

  I got that message and i dont know what it is means: Oct 21 12:24:26 lex mysql-proxy: 2013-10-21 12:24:26: ((error)) last message repeated 98 times Oct 21 12:24:26 lex mysql-proxy: 2013-10-21 12:24:26: ((error)) network-mysqld-packet.c.596: COM_(0x04) should not be (OK|ERR|NULL), got: 00 Oct 21 12:24:26 lex kernel: [4163416.207121] mysql-proxy[14271] trap int3 ip:7ff96e8a4313 sp:7fffb9086ad0 error:0 Any idea what can be the cause of it ?

  Read the article

• Browsing Bombs After a Short While

  - by Peder Rice

  After a reboot, my internet connection lasts perhaps a half hour or so before tanking. I can ping (by both IP and hostname), but I cannot browse. If I restart the "Network Store Interface Service", my connection comes back. What could be failing with that service or its dependent services that would kill my ability to browse? For some system info, I'm using a Sony Vaio with a fully-patched Windows Vista install and with an Intel 3945ABG wireless adapter.

  Read the article

• How secure is the Subversion connection to an https URL

  - by reprogrammer

  I'm using TortoiseSVN as my subversion client on Windows 7. My subversion repository has an https URL. I'm on a public network and I'd like to make sure that my connection to the server is secure. I wonder if TortoiseSVN encrypts my password when it talks to my repository.

  Read the article

• Server unable to communicate OUT, fine serving traffic

  - by jonoabroad

  We have several servers that are randomly loses the ability to communicate out to other nodes on the local network and internet. However websites are being served fine and we still have ssh access. A reboot seems to fix the problem for a few days. The servers are running 10.5.X and are fully up to date with software updates. Does anyone have any opinions, we think it is probably an ISP router, but we are guessing. Cheers Jono

  Read the article

< Previous Page | 400 401 402 403 404 405 406 407 408 409 410 411  | Next Page >