Search Results

Search found 13752 results on 551 pages for 'ip protocol'.

Page 405/551 | < Previous Page | 401 402 403 404 405 406 407 408 409 410 411 412  | Next Page >

• Can't access LAN computers with SSH

  - by endolith

  I got a new Windows 7 machine, and was using VNC,SSH etc to connect to my Ubuntu machine, and it worked fine previously. Now it doesn't work if I use the machine's hostname or local IP, but if I use the DynDNS name, it works. I can also access it from my Android phone using the local hostname over SSH. If I try to connect with SSH to the hostname, it says "Host does not exist". VNC says "Failed to get server address". NX says "no address associated with name", and I don't see it in Windows' "Network" folder. I've rebooted everything. I've turned off Windows firewall. It was working fine a few days ago, but now it's not. How do I figure out what's blocking it?

  Read the article

• Apache: How can I make my localhost on 192.168.1.101 visible from 192.168.1.102?

  - by takpar

  Hi, I've setup a Apache web server on Ubuntu Linux. I can see http://localhost well. But I can't see localhost from other machines in my network using IP address: http://192.168.1.101 I added the lines below to my apache conf: `Allow from 192.168.1` but it did not work. It says "the connection has timed out". what should i do? PS: adp@adp-desktop:~$ sudo netstat -ap | grep apache tcp 0 0 *:www *:* LISTEN 10581/apache2 tcp 0 0 localhost:www localhost:46017 ESTABLISHED 10586/apache2

  Read the article

• veriSign SSL Cert for subdomain

  - by Asghar

  I have purchase SSL for secure Site from Verisign. I have configured it and its working properly on https://www.example.com . I have subdomain app.example.com . i need to work SSL on this domain also. I have 2 Questions. 1- Will same SSL will work for the subdomain too? [My SSL is not wildcard SSL] 2- If it will not work. then how can i change the same SSL that it should only work on app.example.com. i mean is there any way to change purchased SSL for subdomain. and How can i do this. https://www.example.com and http://app.example.com point to the same IP address xxx.xxx.xxx.xxx

  Read the article

• Address VMWare Fusion Linux guest by hostname?

  - by amrox

  I have a Ubuntu Server 9.04 image set up in VMWare Fusion 3.0.0, using the NAT option for the guest's network connection. From the Mac host, I can ssh to the linux guest just fine using it's IP address, but I would like to be able to refer to it by hostname for connivence. ie: mac-host:~ ssh [email protected] I had a similar setup using Parallels a couple years ago, but I don't remember how it was set up. It may have "just worked". Any suggestion on how to make this work?

  Read the article

• SQL Server Configuration Manager menu won't show up

  - by Aurelien Gasser

  I'm running a Windows 8 VM on a MacBook using Parallels Desktop 9. On this Windows VM, I have a SQL Server instance running perfectly. However, when I launch SQL Server Configuration Manager, and I want to enable an IP configuration, the Enable menu options are invisible : Here is a screenshot : http://i.imgur.com/PY7qGup.png (I don't have enough reputation to display the image inline) When I click the arrow, a contextual menu should appear with 2 choices "Yes" or "No". Instead, a tiny contextual menu appears, but it's empty. I tried using my keyboard tab/space/arrows keys without success. Has anyone faced/solved the same problem ?

  Read the article

• How can I run a game server on a computer behind a NAT, if I have another computer not behind a NAT?

  - by Macha

  My home connection is part of a large NAT, outside my control. Inside my home, my router has a NAT, under my control. I control a public facing Linux VPS with one IP address, outside my home network. Ideally, what I'd like to do is set something up so that I connect my home computer to my VPS, and after that port X on my VPS leads to port Y on my home computer, for the purposes of running a game server of a game that does not run under Linux. Is this possible?

  Read the article

• Want to SASL/TLS authentication

  - by Naval

  I want to send mail from remote client from my server(centos 5 and 64 bit) for this i need to sasl auth but i have no idea about it what changes i have to make in my server and client here I want to make things more clear my server's hostname/Ip is = test02.s80.in/176.67.172.209 now i want to authenticat remote client vps2.smail.info and vps1.smail.info to deliver mail .. so plz help me if any systematic way to do sasl/tls authentication for these clients... i am using DNS load-balancing(round-robin) mx record lookup technique for load balancing..

  Read the article

• How to enable RDP to a Server 2008 R2 on another network? VM network

  - by Saariko

  I have a W2008 R2 installed on a different network (I am on 192.168.0.x - new server on 192.168.3.x) I had trouble ping and RDP to it. I disabled the firewall to test the connection: and that opened the ping feature but I still can not RDP to that machine. the allow remote access is enabled As per sinni80 idea - Here is the error message The networks are divided by a Fortigate 60-B router - 2ndy interface for the gateway is 192.168.3.254 (and pingable from all) any to any rule on both networks is in place. As per Joe Schmoe idea - I am able to RDP to 192.168.3.1 from 192.168.3.3 (which is on the same network) Data to add: - The servers are on a VM host, each of the servers has 2 nics one is DHCP enabled into the 192.168.0.x network 2nd is static IP in the 192.168.3.x -- Further information: The network 192.168.0.x - are on a domain network (active Directory) The network 192.168.3.x - are grouped in a workgroup What should I check more please?

  Read the article

• VMware 1.0.1 Windows7 - Ubuntu hostnames

  - by Kyle K

  I'm trying to run Ubuntu as the guest OS using VMWware 1.0.10 with Windows 7 Ultimate as the host OS. I had this set up previously with Win XP as the host OS and in fact I'm using the same .vmx My problem is I can't get either Win7 or Ubuntu to be able to ping the other by hostname. After installing Samba and Winbind on Ubuntu, I was able to get this working when under WinXP, but for some reason I can't get it to work under Win7. I can ping by IP Address, and the guest OS even shows up by hostname under the Windows networking panel (but of course I can't do anything with it), but pinging using short hostnames just won't work. Also, Win7 firewall is turned off completely.

  Read the article

• dns hierarchy not working !! Please help

  - by nikhilelite

  (DNS1 ,WWW1, Gateway1) (sub-internal network) (DNS0,WWW0,Gateway0) (internal network) DNS1: 192.168.250.3/24 WWW1: 192.168.250.4/24 Gateway1: 192.168.250.1 /24 (internal) :: 192.168.0.150 to 192.168.0.175 (external) DNS0:192.168.0.197/24 WWW0:192.168.0.197/24 Gateway0: 192.168.0.1 (internal) :: 69.94.x.x (external, dynamic ,isp control) Expected behavior: When using dig from internal (192.168.250.0/24) hosts, and query about domain from 192.168.0.197/16 nameserver's hosts (for which its authoritative) , it should return the ip address. Whats happening: After dig, answer section empty, the query is trying to access a.root server instead of 192.168.0.197 ,even though i have defined 192.168.0.197 as dns in gateway1's resolv.conf Why? I need this working asap, can anyone here help ?

  Read the article

• Windows Advanced Firewall certificate based IPSEC

  - by Tim Brigham

  I'm working on migrating from using IPSEC settings stored under the 'IP Security Policies on Active Directory' to using the 'Windows Firewall with Advanced Security' for my 2008+ boxes. I have successfully been able to get this set up using Kerberos authentication, however my openswan implementation on my Linux boxes is using certificates. Whenever I try changing the authentication method to computer certificate (using RSA and my root CA) the connection is bombing out. I've made this change at both a connection request policy and on the IPSEC settings on the root Windows Firewall with Advanced Security node. The windows event log shows the authentication request is taking place but failing negotiating a mode. What am I missing here?

  Read the article

• Is there a free tool/package that can monitor web traffic and display URLS accessed? [closed]

  - by Anthony

  I couldn't find a similar question but then maybe I am searching for the wrong terms. A few years ago I used a router like device, I'm pretty sure it was a SonicWall, that did this on a clients site. Basically all traffic would be routed through this device and it allowed the manager/administrator to inspect web usage of the workers, determine how often certain resources were accessed and block them if necessary (much like content filter). It showed reports based on domain name reached etc. Facebbok.com, Bebo.com and so on. It also displayed the usual IP traffic information etc. it was a UTM also. I have tried Endian firewall, with it's NTOP install, but I don't think that will show URLs browsed. Maybe I just haven't found it in NTOP yet? I need this to troubleshoot connection and traffic issue at my home, with about twenty devices/users so didn't want to buy a dedicated solution and have spare hardware to use a community product.

  Read the article

• Can ping localhost but can't browse

  - by Anna

  I know this is a pretty common question but I did my research and couldn't find a solution for this issue. I'm configuring a development application server and I came to the point where I can ping both localhost and 127.0.0.1, but I cannot browse either of them from IE or Firefox. I can browse and ping other websites (such as google) just fine. I tried flushing the dns (ipconfig /flushdns), restarting the IIS Admin service, restarting IIS itself, etc, and nothing seems to work. The results from ipconfig /all shows IP Rounting Enabled = No and WINS Proxy Enabled = No. Hwat is intriguing to me is that I compared everything in IIS in the dev environment with the production environment and the settings are the same, but I can browse localhost in production, but not in dev! What could be causing the inability to browse localhost and 127.0.0.1 from IE and Firefox?

  Read the article

• Bound external Cisco CIGESM ports to a specific BladeServer

  - by Vinícius Ferrão

  We have an IBM BladeCenter with 14 blade servers and one external Cisco CIGESM for Ethernet connectivity. Since this hardware is a little old, we will use it for other services, and we want to run a pfSense instance on one of the blades. It's just an Firewall Appliance, but it needs two network interfaces: one for the WAN and the other one for LAN access. Our architecture works on top of static routes, we don't use NAT, so we got the WAN IP in one interface routing to the another one. The main problem is how to plug the WAN cable in one of the four external ports and make it exclusive to the blade server containing the firewall. And we also need an exit port that goes through a 3COM 4200G switch that makes the internal routing and VLAN separation. Thanks in advance

  Read the article

• LAN connection suddenly domain_not_set.invalid

  - by Liam Coates

  I went to work today - internet fine as always. Came back, dreaded yellow triangle. I can connect wirelessly like i am now on my tablet. Thats completely fine. But through LAN I get the domain_not_set.Invalid message if I renew my IP for example. It seems I just don't have a DNS. But I have literally not touched anything no ones even been in the house. Hows that happen? Any help on why only wireless works would be great, I am gonna buy a wireless adapter tomorrow for the interim but I would like to know why. Thanks.

  Read the article

• how to create xampp mysql remote connection within my office ,

  - by Ranjit Kumar

  Before asking this question : i have gone through this link How do I allow remote access to mysql using xampp? But i couldnt make it up !!! i have installed xampp using xamppinstaller.exe and its version is 3.1.0. i am heidisql Gui for database managament i tried the same by changing the # bind-address from "127.0.0.1" to my system ip address as # bind-address to "192.168.1.69" After changing and restarting my xampp mysql i went to other system and tried to login (hedisql) with the hostname 192.168.1.69 and it gave me an error saying Error 1130(0000): host' ....' is not allowed to connect to this mysql server. what should i do please help me !!

  Read the article

• Firewire 800 with Windows

  - by Amitesh

  I have two windows machine with windows server 2003 installed on them. I am running a Lab View script on 1 machine and storing the data. But since it has less memory, I want to transfer data to another machine using firewire 800. Is it possible to configure out the second machine just as an external HDD attached to it and write data directly to it? (This is possible with MACs) Dont want to use the ethernet (internet/ TCP/IP prot.) to transfer the data. Is it possible? Thanks.

  Read the article

• Git and Amazon EC2 public key denied

  - by MrNart

  I had git working before on /var/html/projectfolder and realized it was a security risk so I made a new folder /projects from the root folder and tried to replicate what I did and now it doesnt work. Here is the backlog of what I did for my local machine and EC2 - server Server-EC2 1.I added my public key to the authorized_user file in ~/.ssh folder 2.Create a bare repository git init --bare 3.Change folder permissions to sudo chgrp -R ec2-user * sudo chmod -R g+ws * Local Machine create a local repository with git init touch, add, commit readme file pointed origin master to ec2 via git remote add origin ssh://ec2-user@remote-ip/path/to/folder This is my output: Permission Denied (publickey) fatal: The remote end hung up unexpectedly

  Read the article

• DNS Zone file and virtual host question

  - by Jake

  Hi all, I'm trying to set up a virtual host for redmine.SITENAME.com. I've edited the httpd.conf file and now I'm trying to edit my DNS settings. However, I'm not sure exactly what to do. Here's an snippet of what's already in the named.conf file (the file was made by someone else who is unreachable): zone "SITENAME.com" { type master; file "SITENAME.com"; allow-transfer { ip.address.here.00; common-allow-transfer; }; }; I figure if I want to get redmine.SITENAME.com working, I need to copy that entry and just replace SITENAME.com with redmine.SITENAME.com but will that work? I was under the impression I needed a .db file but I don't see any reference to one in the current named.conf file. Any advice would be great and if you need more info to answer the question, don't hesitate to ask.

  Read the article

• Asus EEE PC 1005HA (XP Home) refuses to connect to Virgin Mobile MiFi

  - by Dennis Wurster

  My client has an Asus EEE PC model 1005HA, and we're attempting to connect it to the WiFi network created by a VirginMobile MiFi unit. They also have a MacBook Pro with Snow Leopard that has absolutely no issue connecting to the MiFi. The specific symptom is that the netbook fails to lease an IP address from the MiFi unit. I supply the 12-digit numerical password (WPA) to the netbook, it throws a 'waiting for network' dialog with an indeterminate progress indicator, and then times out. Update: We've determined that this behavior has stopped when the EEE PC and the MiFi unit were taken out of the client's home, and to a different home that didn't have an existing wifi network. Similarly, when taken to a third location that didn't have wifi, the EEE PC and MiFi got along swimmingly. My current theory is that the existing wifi networks and the wifi leg of the MiFi unit are on the same channel and competing with one another. Perhaps the MacBook Pro has the capability to overcome this interference, while the EEE PC doesn't.

  Read the article

• setting up bridged adapter for VPN server

  - by B. VB.

  I have an Ubuntu linux Linode server that I am trying to install OpenVPN on. I'm following the tutorials (which, it turns out, are quite incomplete). auto br0 iface br0 inet static address 192.168.0.10 network 192.168.0.0 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off When I add this chunk in my /etc/network/interfaces, and I restart networking, my eth0 interface does not have an IP and I cannot get on the network (I need to use a buggy, slow, and annoying AJAX term to do damage repair). Why does adding this screw everything up? Any tips on how to set up this bridged adapter?? Thanks in advance!

  Read the article

• nginx automatic failover load balancing

  - by robinmag

  Hi, I'm using nginx and NginxHttpUpstreamModule for loadbalancing. My config is very simple: upstream lb { server 127.0.0.1:8081; server 127.0.0.1:8082; } server { listen 89; server_name localhost; location / { proxy_pass http://lb; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } } But with this config, when one of 2 backend server is down, nginx still routes request to it and it results in timeout half of the time :( Is there any solution to make nginx to automatically route the request to another server when it detects a downed server. Thank you.

  Read the article

• connect to a machine inside the intranet from outside with same address used inside

  - by pietrosld

  Hi all! I have a server inside my intranet, in wich i have apache running with some web applications. when i'm at office the url i use to connect is zeus.mydomain.it, it works couse i have in my /etc/hosts a record 192.168.0.11 zeus.mydomain.it, but obviously it does not work when i'm outside in different network. i have a internet connectino with static ip, so i can connect to my intranet form outside. the question is: how can i connect to the intranet server using zeus.mydomain.it from inside and from outside my intranet ? thanks!! Pietro.

  Read the article

• IPSec on Domain Controllers and Trusted Domains

  - by OneLogicalMyth

  I am looking at configuring IPSec as follows: Isolation Request authentication for inbound and outbound connections Computer and user (Kerberos V5) I am looking to do a blanket deployment across all servers and domain controllers. Workstations I will leave as not set. What impact in terms of the domain controllers with the 2-way forest trust do think I would see? Should I exclude the IP addresses of the trusted domain controllers? I don't want to stop communication between the current and trusted forest, however I do want IPsec to be used within the current forest on all servers. The trusted forest is running 2008 R2 and the current forest is 2012 R2.

  Read the article

• Ubuntu 12.04 host lookups extremely slow

  - by tubaguy50035

  I'm having issues with one of my servers taking a long time to look up host names. This is an Ubuntu 12.04 box, so I've tried following the new resolvconf directives. In my /etc/network/interfaces file, I defined my name servers like this: auto eth0 iface eth0 inet static address someaddress netmask 255.255.255.0 gateway 198.58.103.1 dns-nameservers 74.14.179.5 72.14.188.5 In my /etc/resolv.conf, I see these name servers, like this: # Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8) # DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN nameserver 74.14.179.5 nameserver 72.14.188.5 On another box, I edited the resolv.conf directly as directed by my hosts' setup help files. It looks like this: domain members.linode.com search members.linode.com nameserver 72.14.179.5 nameserver 72.14.188.5 options rotate This second box has no issues with host name look ups and responds quite quickly. Could not having the domain and search directives make my look ups slow? By slow, I mean it's taking anywhere from 5 to 15 seconds to find the IP address of a host.

  Read the article

< Previous Page | 401 402 403 404 405 406 407 408 409 410 411 412  | Next Page >