Search Results

Search found 10699 results on 428 pages for 'apple mail'.

Page 408/428 | < Previous Page | 404 405 406 407 408 409 410 411 412 413 414 415  | Next Page >

• Issue in setting up VPN connection (IKEv1) using android (ICS vpn client) with Strongswan 4.5.0 server

  - by Kushagra Bhatnagar

  I am facing issues in setting up VPN connection(IKEv1) using android (ICS vpn client) and Strongswan 4.5.0 server. Below is the set up: Strongswan server is running on ubuntu linux machine which is connected to some wifi hotspot. Using the steps in this guide link, I generated CA, server and client certificate. Once certificates are generated, following (clientCert.p12 and caCert.pem) are sent to mobile via mail and installed on android device. Below are the ip addresses assigned to various interfaces Linux server wlan0 interface ip where server is running: 192.168.43.212, android device eth0 interface ip address: 192.168.43.62; Android device is also attached with the same wifi hotspot. On the Android device, I uses IPsec Xauth RSA option for setting up VPN authentication configuration. I am using the following ipsec.conf configuration: # basic configuration config setup plutodebug=all # crlcheckinterval=600 # strictcrlpolicy=yes # cachecrls=yes nat_traversal=yes # charonstart=yes plutostart=yes # Add connections here. # Sample VPN connections conn ios1 keyexchange=ikev1 authby=xauthrsasig xauth=server left=%defaultroute leftsubnet=0.0.0.0/0 leftfirewall=yes leftcert=serverCert.pem right=192.168.43.62 rightsubnet=10.0.0.0/24 rightsourceip=10.0.0.2 rightcert=clientCert.pem pfs=no auto=add      With the above configurations when I enable VPN on android device, VPN connection is not successful and it gets timed out in Authentication phase. I ran wireshark on both the android device and strongswan server, from the tcpdump below are the observations. Initially Identity Protection (Main mode) exchanges happens between device and server and all are successful. After all successful Identity Protection (Main mode) exchanges server is sending Transaction (Config mode) to device. In reply android device is sending Informational message instead of Transaction (Config mode) message. Further server is keep on sending Transaction (Config mode) message and device is again sending Identity Protection (Main mode) messages. Finally timeout happens and connection fails. I also capture Strongswan server logs and below are the snippets from the server logs which also verifies the same(described above). Apr 27 21:09:40 Linux pluto[12105]: | **parse ISAKMP Message: Apr 27 21:09:40 Linux pluto[12105]: | initiator cookie: Apr 27 21:09:40 Linux pluto[12105]: | 06 fd 61 b8 86 82 df ed Apr 27 21:09:40 Linux pluto[12105]: | responder cookie: Apr 27 21:09:40 Linux pluto[12105]: | 73 7a af 76 74 f0 39 8b Apr 27 21:09:40 Linux pluto[12105]: | next payload type: ISAKMP_NEXT_HASH Apr 27 21:09:40 Linux pluto[12105]: | ISAKMP version: ISAKMP Version 1.0 Apr 27 21:09:40 Linux pluto[12105]: | exchange type: ISAKMP_XCHG_INFO Apr 27 21:09:40 Linux pluto[12105]: | flags: ISAKMP_FLAG_ENCRYPTION Apr 27 21:09:40 Linux pluto[12105]: | message ID: a2 80 ad 82 Apr 27 21:09:40 Linux pluto[12105]: | length: 92 Apr 27 21:09:40 Linux pluto[12105]: | ICOOKIE: 06 fd 61 b8 86 82 df ed Apr 27 21:09:40 Linux pluto[12105]: | RCOOKIE: 73 7a af 76 74 f0 39 8b Apr 27 21:09:40 Linux pluto[12105]: | peer: c0 a8 2b 3e Apr 27 21:09:40 Linux pluto[12105]: | state hash entry 25 Apr 27 21:09:40 Linux pluto[12105]: | state object not found Apr 27 21:09:40 Linux pluto[12105]: packet from 192.168.43.62:500: Informational Exchange is for an unknown (expired?) SA Apr 27 21:09:40 Linux pluto[12105]: | next event EVENT_RETRANSMIT in 10 seconds for #9 Can anyone please provide update on this issue. Why the VPN connection gets timed out and why the ISAKMP exchanges are not proper between Android and strongswan server.

  Read the article

• Linux not buffering block I/O when the device is not "in use" (i.e. mounted)

  - by Radek Hladík

  I am installing new server and I've found an interesting issue. The server is running Fedora 19 (3.11.7-200.fc19.x86_64 kernel) and is supposed to host a few KVM/Qemu virtual servers (mail server, file server, etc..). The HW is Intel(R) Xeon(R) CPU 5160 @ 3.00GHz with 16GB RAM. One of the most important features will be Samba server and we have decided to make it as virtual machine with almost direct access to the disks. So the real HDD is cached on SSD (via bcache) then raided with md and the final device is exported into the virtual machine via virtio. The virtual machine is again Fedora 19 with the same kernel. One important topic to find out is whether the virtualization layer will not introduce high overload into disk I/Os. So far I've been able to get up to 180MB/s in VM and up to 220MB/s on real HW (on the SSD disk). I am still not sure why the overhead is so big but it is more than the network can handle so I do not care so much. The interesting thing is that I've found that the disk reads are not buffered in the VM unless I create and mount FS on the disk or I use the disks somehow. Simply put: Lets do dd to read disk for the first time (the /dev/vdd is an old Raptor disk 70MB/s is its real speed): [root@localhost ~]# dd if=/dev/vdd of=/dev/null bs=256k count=10000 ; cat /proc/meminfo | grep Buffers 2621440000 bytes (2.6 GB) copied, 36.8038 s, 71.2 MB/s Buffers: 14444 kB Rereading the data shows that they are cached somewhere but not in buffers of the VM. Also the speed increased to "only" 500MB/s. The VM has 4GB of RAM (more that the test file) [root@localhost ~]# dd if=/dev/vdd of=/dev/null bs=256k count=10000 ; cat /proc/meminfo | grep Buffers 2621440000 bytes (2.6 GB) copied, 5.16016 s, 508 MB/s Buffers: 14444 kB [root@localhost ~]# dd if=/dev/vdd of=/dev/null bs=256k count=10000 ; cat /proc/meminfo | grep Buffers 2621440000 bytes (2.6 GB) copied, 5.05727 s, 518 MB/s Buffers: 14444 kB Now lets mount the FS on /dev/vdd and try the dd again: [root@localhost ~]# mount /dev/vdd /mnt/tmp [root@localhost ~]# dd if=/dev/vdd of=/dev/null bs=256k count=10000 ; cat /proc/meminfo | grep Buffers 2621440000 bytes (2.6 GB) copied, 4.68578 s, 559 MB/s Buffers: 2574592 kB [root@localhost ~]# dd if=/dev/vdd of=/dev/null bs=256k count=10000 ; cat /proc/meminfo | grep Buffers 2621440000 bytes (2.6 GB) copied, 1.50504 s, 1.7 GB/s Buffers: 2574592 kB While the first read was the same, all 2.6GB got buffered and the next read was at 1.7GB/s. And when I unmount the device: [root@localhost ~]# umount /mnt/tmp [root@localhost ~]# cat /proc/meminfo | grep Buffers Buffers: 14452 kB [root@localhost ~]# dd if=/dev/vdd of=/dev/null bs=256k count=10000 ; cat /proc/meminfo | grep Buffers 2621440000 bytes (2.6 GB) copied, 5.10499 s, 514 MB/s Buffers: 14468 kB The bcache was disabled while testing and the results are same on faster (newer) HDDs and on SSD (except for the initial read speed of course). To sum it up. When I read from the device via dd first time, it gets read from the disk. Next time I reread it gets cached in the host but not in the guest (thats actually the same issue, more on that later). When I mount the filesystem but try to read the device directly it gets cached in VM (via buffers). As soon as I stop "using" it, buffers are discarded and the device is not cached anymore in the VM. When I looked into buffers value on the host I realized that the situation is the same. The block I/O gets buffered only when the disk is in use, in this case it means "exported to a VM". On host, after all the measurement done: 3165552 buffers On the host, after the VM shutdown: 119176 buffers I know it is not important as the disks will be mounted all the time but I am curious and I would like to know why it is working like this.

  Read the article

• Linux bcm43224 wifi adapter slows down a couple minutes after boot

  - by Blubber

  I just installed Ubuntu on my mid 2012 MacBook Air. Everything worked out of the box, but the wifi is showing some weird behavior. When I first login it's really fast, loading google.com is near instant, and browsing in general feels at least as smooth as it did on Mac OS. However, after a couple minutes the connection slows down dramatically, sometimes it takes over 5s to load google.com, a simple reboot fixes the problem for another couple minutes. Specs: Wifi: 02:00.0 Network controller: Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01) Driver: open-source brcmsmac driver Kernel: Linux wega 3.8.0-21-generic #32-Ubuntu SMP Tue May 14 22:16:46 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux Distro: Ubuntu 13.04 (uptodate) I tried a number of things, none of which actually helped Use proprietary sta driver from broadcom Installed firmware into /lib/firmware/brcms (which, as far as I can tell from logs, does not get loaded at all) Switch router to only use 2.4 OR 5 GHz Set router to only use a OR g OR n Set router to use AES encryption only Turned off power management on the adapter Set regulatory region to the correct value (NL) on both router and laptop Disable ipv6 Nothing seems to help, the slowdown always occurs. I did notice that the latency (ping google.com) stays roughly the same (around 9ms). Below is some more information that might be of use. $ lspci -nnk | grep -iA2 net 02:00.0 Network controller [0280]: Broadcom Corporation BCM43224 802.11a/b/g/n [14e4:4353] (rev 01) Subsystem: Apple Inc. Device [106b:00e9] Kernel driver in use: bcma-pci-bridge $ rfkill list 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no $ lsmod Module Size Used by dm_crypt 22820 1 arc4 12615 2 brcmsmac 550698 0 coretemp 13355 0 kvm_intel 132891 0 parport_pc 28152 0 kvm 443165 1 kvm_intel ppdev 17073 0 cordic 12574 1 brcmsmac brcmutil 14755 1 brcmsmac mac80211 606457 1 brcmsmac cfg80211 510937 2 brcmsmac,mac80211 bnep 18036 2 rfcomm 42641 12 joydev 17377 0 applesmc 19353 0 input_polldev 13896 1 applesmc snd_hda_codec_hdmi 36913 1 microcode 22881 0 snd_hda_codec_cirrus 23829 1 nls_iso8859_1 12713 1 uvcvideo 80847 0 btusb 22474 0 snd_hda_intel 39619 3 videobuf2_vmalloc 13056 1 uvcvideo snd_hda_codec 136453 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec_cirrus bcm5974 17347 0 bluetooth 228619 22 bnep,btusb,rfcomm snd_hwdep 13602 1 snd_hda_codec lpc_ich 17061 0 videobuf2_memops 13202 1 videobuf2_vmalloc videobuf2_core 40513 1 uvcvideo videodev 129260 2 uvcvideo,videobuf2_core bcma 41051 1 brcmsmac snd_pcm 97451 3 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel snd_page_alloc 18710 2 snd_pcm,snd_hda_intel snd_seq_midi 13324 0 snd_seq_midi_event 14899 1 snd_seq_midi snd_rawmidi 30180 1 snd_seq_midi snd_seq 61554 2 snd_seq_midi_event,snd_seq_midi snd_seq_device 14497 3 snd_seq,snd_rawmidi,snd_seq_midi snd_timer 29425 2 snd_pcm,snd_seq snd 68876 16 snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device,snd_hda_codec_cirrus mei 41158 0 soundcore 12680 1 snd apple_bl 13673 0 mac_hid 13205 0 lp 17759 0 parport 46345 3 lp,ppdev,parport_pc usb_storage 57204 0 hid_apple 13237 0 hid_generic 12540 0 ghash_clmulni_intel 13259 0 aesni_intel 55399 399 aes_x86_64 17255 1 aesni_intel xts 12885 1 aesni_intel lrw 13257 1 aesni_intel gf128mul 14951 2 lrw,xts ablk_helper 13597 1 aesni_intel cryptd 20373 4 ghash_clmulni_intel,aesni_intel,ablk_helper i915 600351 3 ahci 25731 3 libahci 31364 1 ahci video 19390 1 i915 i2c_algo_bit 13413 1 i915 drm_kms_helper 49394 1 i915 usbhid 47074 0 drm 286313 4 i915,drm_kms_helper hid 101002 3 hid_generic,usbhid,hid_apple $ dmesg | egrep 'b43|bcma|brcm|[F]irm' [ 0.055025] [Firmware Bug]: ioapic 2 has no mapping iommu, interrupt remapping will be disabled [ 0.152336] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored [ 2.187681] pci_root PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-99] only partially covers this bridge [ 12.553600] bcma-pci-bridge 0000:02:00.0: enabling device (0000 -> 0002) [ 12.553657] bcma: bus0: Found chip with id 0xA8D8, rev 0x01 and package 0x08 [ 12.553688] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0) [ 12.553715] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0) [ 12.553764] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0) [ 12.605777] bcma: bus0: Bus registered [ 12.852925] brcmsmac bcma0:0: mfg 4bf core 812 rev 23 class 0 irq 17 [ 13.085176] brcmsmac bcma0:0: brcms_ops_bss_info_changed: qos enabled: false (implement) [ 13.085186] brcmsmac bcma0:0: brcms_ops_config: change power-save mode: false (implement) [ 20.862617] brcmsmac bcma0:0: brcmsmac: brcms_ops_bss_info_changed: associated [ 20.862622] brcmsmac bcma0:0: brcms_ops_bss_info_changed: arp filtering: enabled true, count 0 (implement) [ 20.862625] brcmsmac bcma0:0: brcms_ops_bss_info_changed: qos enabled: true (implement) [ 20.897957] brcmsmac bcma0:0: brcms_ops_bss_info_changed: arp filtering: enabled true, count 1 (implement) $ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"wlan" Mode:Managed Frequency:5.22 GHz Access Point: E0:46:9A:4E:63:9A Bit Rate=65 Mb/s Tx-Power=17 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=63/70 Signal level=-47 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:13 Invalid misc:56 Missed beacon:0

  Read the article

• Process not Listed by PS or in /proc/

  - by Hammer Bro.

  I'm trying to figure out how to operate a rather large Java program, 'prog'. If I go to its /bin/ dir and configure its setenv.sh and prog.sh to use local directories and my current user account. Then I try to run it via "./prog.sh start". Here are all the relevant bits of prog.sh: USER=(my current account) _CMD="/opt/jdk/bin/java -server -Xmx768m -classpath "${CLASSPATH}" -jar "${DIR}/prog.jar"" case "${ACTION}" in start) nohup su ${USER} -c "exec ${_CMD} >>${_LOGFILE} 2>&1" >/dev/null & echo $! >${_PID} echo "Prog running. PID="`cat ${_PID}` ;; stop) PID=`cat ${_PID} 2>/dev/null` echo "Shutting down prog: ${PID} kill -QUIT ${PID} 2>/dev/null kill ${PID} 2>/dev/null kill -KILL ${PID} 2>/dev/null rm -f ${_PID} echo "STOPPED `date`" >>${_LOGFILE} ;; When I actually do ./prog.sh start, it starts. But I can't find it at all on the process list. Nor can I kill it manually, using the same command the shell script uses. But I can tell it's running, because if I do ./prog.sh stop, it stops (and some temporary files elsewhere clean themselves out). ./prog.sh start Prog running. PID=1234 ps eaux | grep 1234 ps eaux | grep -i prog.jar ps eaux >> pslist.txt (It's not there either by PID or any clear name I can find: prog, java or jar.) cd /proc/1234/ -bash: cd: /proc/1234/: No such file or directory kill -QUIT 1234 kill 1234 kill -KILL 1234 -bash: kill: (1234) - No such process ./prog.sh stop Shutting down prog: 1234 As far as I can tell, the process is running yet not in any way listed by the system. I can't find it in ps or /proc/, nor can I kill it. But the shell script can still stop it properly. So my question is, how can something like this happen? Is the process supremely hidden, actually unlisted, or am I just missing it in some fashion? I'm trying to figure out what makes this program tick, and I can barely prove that it's ticking! Edit: ps eu | grep prog.sh (after having restarted; so random PID) 50038 19381 0.0 0.0 4412 632 pts/3 S+ 16:09 0:00 grep prog.sh HOSTNAME=machine.server.com TERM=vt100 SHELL=/bin/bash HISTSIZE=1000 SSH_CLIENT=::[STUFF] 1754 22 CVSROOT=:[DIR] SSH_TTY=/dev/pts/3 ANT_HOME=/opt/apache-ant-1.7.1 USER=[USER] LS_COLORS=[COLORS] SSH_AUTH_SOCK=[DIR] KDEDIR=/usr MAIL=[DIR] PATH=[DIRS] INPUTRC=/etc/inputrc PWD=[PWD] JAVA_HOME=/opt/jdk1.6.0_21 LANG=en_US.UTF-8 SSH_ASKPASS=/usr/libexec/openssh/gnome-ssh-askpass M2_HOME=/opt/apache-maven-2.2.1 SHLVL=1 HOME=[~] LOGNAME=[USER] SSH_CONNECTION=::[STUFF] LESSOPEN=|/usr/bin/lesspipe.sh %s G_BROKEN_FILENAMES=1 _=/bin/grep OLDPWD=[DIR] I just realized that the stop) part of prog.sh isn't actually a guarantee that the process it claims to be stopping is running -- it just tries to kill the PID and suppresses all output then deletes the temporary file and manually inserts STOPPED into the log file. So I'm no longer so certain that the process is always running when I ps for it, although the code sample above indicates that it at least runs erratically. I'll continue looking into this undocumented behemoth when I return to work tomorrow.

  Read the article

• Server Admin is not allowing me to configure DNS

  - by Clinton Blackmore

  We have a Mac OS X 10.5.8 Server running DNS (and a few other services). When I connect to it (using Server Admin 10.5.3 [which comes from the Server Admin 10.5.7 tools]), and click to look at the DNS settings, all appears normal -- it shows many reverse entries and two top-level domains. However, when I select one of our domains and open the disclosure triangle, the list is empty! [There should be over a dozen entries, and the reverse entries do show up.] If I then tell it I want to add, say, an A Record to the domain, almost everything disappears -- and I am left with a list showing our two domains, one with a disclosure triangle underneath it showing a single entry, and one reverse entry to correspond to the new A record. named appears to be working fine. DNS names resolve. It appears to simply be that Server Admin is having problems with the data on the computer. No one here would have manually created a DNS entry. Now, while I think I've backed up the DNS (I backed up /var/named/, /etc/named.conf, and /etc/dns/, as mentioned here), I'm really not sure if just replacing the files would restore the DNS settings we have if things go south. I am contemplating going to settings and changing the log level from "Information" to "Debug", but 1) I am just a little concerned that it might write a bad configuration to the disk, and 2) I think it would only affect named and not Server Admin, and, so far as I can tell, named is not having a problem. (Nothing looks strange in /Library/Logs/named.log when I open it via Console/Terminal. Oddly, though, when I click on the 'log' button for DNS in Server Admin, I see no text at all, just a fully white window. When I look at one of our secondary DNS servers, I am able to see the log file through Server Admin.) This entry appears in the system log when I run Server Admin on the server: Jun 17 09:02:08 od1 Server Admin[3892]: Unexpected call to doMarkConfigurationAsDirty by 'DNS' plugin during updateConfigurationViewFromDescription It seems to occur after I've looked at DNS, look at another service, and then click back on DNS. Think that the most likely cause is a corrupt configuration file, I glanced through all the files that I backed up, and none of them is obviously gobbledygook. Here are some oddities I find when running Server Admin from a remote computer to manage the DNS. When I click to see the log file for DNS, the server starts writing messages like these to its system.log: Jun 17 09:59:04 od1 kernel[0]: Limiting open port RST response from 252 to 250 packets per second Jun 17 09:59:06 od1 kernel[0]: Limiting open port RST response from 258 to 250 packets per second This stops when I click on a different service. The inderterminate progress indicator (the spinning wheel that appears beside the "Revert" and "Save" buttons in the bottom-right corner of Server Admin) looks really strange. As far as I can tell, instead of just spinning and waiting, it is being told to start spinning repeatedly, resulting in a jerky animation. Here are some of the messages being logged on the computer running Server Admin: At startup: *** ERROR: -[GRAxes computeLayout]:1124 - plotRect height = 0.000000 <= 0.0 *** *** ERROR: -[GRChartView computeLayout]:1194 - Layout for overlay axes (0x18758f50) failed. *** (These messages don't concern me too much as they go away for a while if you delete ~/Library/Preferences/com.apple.ServerAdmin.plist). At shutdown: 2010-06-17 10:02:17.202 Server Admin[7770:10b] *** -[GroupTextField windowDidResignKey:]: unrecognized selector sent to instance 0x16e12490 More concerning are these messages: 2010-06-17 09:59:47.269 Server Admin[7770:10b] Unexpected call to doMarkConfigurationAsDirty by 'DNS' plugin during updateConfigurationViewFromDescription Server Admin(7770,0xb0453000) malloc: *** error for object 0x1c115390: double free *** set a breakpoint in malloc_error_break to debug 2010-06-17 10:01:00.795 Server Admin[7770:10b] *** -[ServiceEntry sessionHost]: unrecognized selector sent to instance 0x2af500 Any thoughts on: what the problem is how I can troubleshoot it or how to fix it? If I do need to wipe out DNS and restart, is there a good way to do this?

  Read the article

• Facing issues in setting up VPN connection(IKEv1) using iphone (Defult Cisco VPN client) and Strongswan 4.5.0 server

  - by Kushagra Bhatnagar

  I am facing issues in setting up VPN connection(IKEv1) using iPhone (Defult Cisco VPN client) and Strongswan 4.5.0 server. The Strongswan server is running on Ubuntu Linux, which is connected to some wifi hotspot. This is the guide which was used. I generated CA, server and client certificate, with the only difference mentioned below. “While generating server certificate, as per link CN=vpn.strongswan.org instead of this I changed CN name to CN=192.168.43.212.” Once certificates are generated, following (clientCert.p12 and caCert.pem) are sent to mobile via mail and installed on iphone. After installation I notice that certificates are considered as trusted also. Below are the ip addresses assigned to various interfaces Linux server wlan0 interface ip where server is running: 192.168.43.212 Iphone eth0 interface ip address: 192.168.43.72. iphone is also attached with the same wifi hotspot. Below is the snapshot of client configurations. Description Strong swan Server 192.168.43.212 Account ipsecvpn Password ***** Use certificate ON Certificate client The above username and password are in sync with the ipsec.secrets file. I am using the following ipsec.conf configuration: # basic configuration config setup plutodebug=all # crlcheckinterval=600 # strictcrlpolicy=yes # cachecrls=yes nat_traversal=yes # charonstart=yes plutostart=yes # Add connections here. # Sample VPN connections conn ios1 keyexchange=ikev1 authby=xauthrsasig xauth=server left=%defaultroute leftsubnet=0.0.0.0/0 leftfirewall=yes leftcert=serverCert.pem right=192.168.43.72 rightsubnet=10.0.0.0/24 rightsourceip=10.0.0.2 rightcert=clientCert.pem pfs=no auto=add With the above configurations when I enable VPN on iphone, it says Could not able to verify server certificate. I ran Wireshark on a Linux server and observe that initially some ISAKMP message exchanges happens between client and server, which are successful but before authorization, client is sending some informational message and soon after this client is showing error as popup Could not able to verify server certificate. Capture logs on Strongswan server and in server logs below errors are observed: From auth.log Apr 25 20:16:08 Linux pluto[4025]: | ISAKMP version: ISAKMP Version 1.0 Apr 25 20:16:08 Linux pluto[4025]: | exchange type: ISAKMP_XCHG_INFO Apr 25 20:16:08 Linux pluto[4025]: | flags: ISAKMP_FLAG_ENCRYPTION Apr 25 20:16:08 Linux pluto[4025]: | message ID: 9d 1a ea 4d Apr 25 20:16:08 Linux pluto[4025]: | length: 76 Apr 25 20:16:08 Linux pluto[4025]: | ICOOKIE: f6 b7 06 b2 b1 84 5b 93 Apr 25 20:16:08 Linux pluto[4025]: | RCOOKIE: 86 92 a0 c2 a6 2f ac be Apr 25 20:16:08 Linux pluto[4025]: | peer: c0 a8 2b 48 Apr 25 20:16:08 Linux pluto[4025]: | state hash entry 8 Apr 25 20:16:08 Linux pluto[4025]: | state object not found Apr 25 20:16:08 Linux pluto[4025]: **packet from 192.168.43.72:500: Informational Exchange is for an unknown (expired?) SA** Apr 25 20:16:08 Linux pluto[4025]: | next event EVENT_RETRANSMIT in 8 seconds for #8 Apr 25 20:16:16 Linux pluto[4025]: | Apr 25 20:16:16 Linux pluto[4025]: | *time to handle event Apr 25 20:16:16 Linux pluto[4025]: | event after this is EVENT_RETRANSMIT in 2 seconds Apr 25 20:16:16 Linux pluto[4025]: | handling event EVENT_RETRANSMIT for 192.168.43.72 "ios1" #8 Apr 25 20:16:16 Linux pluto[4025]: | sending 76 bytes for EVENT_RETRANSMIT through wlan0 to 192.168.43.72:500: Apr 25 20:16:16 Linux pluto[4025]: | a6 a5 86 41 4b fb ff 99 c9 18 34 61 01 7b f1 d9 Apr 25 20:16:16 Linux pluto[4025]: | 08 10 06 01 e9 1c ea 60 00 00 00 4c ba 7d c8 08 Apr 25 20:16:16 Linux pluto[4025]: | 13 47 95 18 19 31 45 30 2e 22 f9 4d 85 2c 27 bc Apr 25 20:16:16 Linux pluto[4025]: | 9e 9b e1 ae 1e 35 51 6f ab 80 f5 73 3c 15 8d 20 Apr 25 20:16:16 Linux pluto[4025]: | 4b 46 47 86 50 24 3f 13 15 7d d5 17 Apr 25 20:16:16 Linux pluto[4025]: | inserting event EVENT_RETRANSMIT, timeout in 40 seconds for #8 Apr 25 20:16:16 Linux pluto[4025]: | next event EVENT_RETRANSMIT in 2 seconds for #10 Apr 25 20:16:16 Linux pluto[4025]: | rejected packet: Apr 25 20:16:16 Linux pluto[4025]: | Apr 25 20:16:16 Linux pluto[4025]: | control: Apr 25 20:16:16 Linux pluto[4025]: | 30 00 00 00 00 00 00 00 00 00 00 00 0b 00 00 00 Apr 25 20:16:16 Linux pluto[4025]: | 6f 00 00 00 02 03 03 00 00 00 00 00 00 00 00 00 Apr 25 20:16:16 Linux pluto[4025]: | 02 00 00 00 c0 a8 2b 48 00 00 00 00 00 00 00 00 Apr 25 20:16:16 Linux pluto[4025]: | name: Apr 25 20:16:16 Linux pluto[4025]: | 02 00 01 f4 c0 a8 2b 48 00 00 00 00 00 00 00 00 Apr 25 20:16:16 Linux pluto[4025]: **ERROR: asynchronous network error report on wlan0 for message to 192.168.43.72 port 500, complainant 192.168.43.72: Connection refused [errno 111, origin ICMP type 3 code 3 (not authenticated)]** Anybody please provide some update about this error and how to solve this issue.

  Read the article

• IBM Server Config questions

  - by Joel Coel

  I have a few questions on a potential server setup. First, the situation: Last year we bought an IBM x3500 server with 2 Xeon E5410's, 9GB RAM, 6 HDDs. The original intent for this server was to replace the old exchange e-mail server. It was brought in, set up, and then shortly after we switched to gmail. Shortly after that my predecessor left for greener pastures, and finally I was hired. So this nice server is now sitting (mostly) idle. This year I have budget again for one server, and of course I want to put this other server to work. I'm thinking about the best use for the two server, and I think I finally have a plan for what I want to do with them. The idea is to use the two newer servers as a pair of VM hosts. I will set up each server with the same 8 VMs, but divide up the load so that only 4 are active per physical host. That means I've normally got 2GB RAM + 2 cores per host. I've done some load testing to pick out what servers to convert to virtual, and chose them so that each host will be capable of handling the entire set of 8 by itself in a pinch with 1 core and 1GB RAM, but would be very taxed to do so. This should take our data center from 13 total servers down to 7. The "servers" I'm replacing are mostly re-purposed desktops, so I'm more than happy to be able to do this. Now it's time to go shopping for the new server. I'd like my two hosts to match as closely as possible, and so I'm looking at IBM again. It also helps that we have some educational matching grant money from IBM that I need to use to help pay for this system (we're a small private college). So finally, (if you're not bored already), we come to my questions: Am I missing anything big or obvious in this plan? I'm a little worried about network performance since the VM hosts will only have 4 nics total where 8 used to be, but I don't think it will be a problem. Is there anything else like this I might be overlooking? Am I making it even too complicated? IBM no longer has a good analog to last year's server. If I want to match the performance (8 cores, 9GB RAM, 1333mhz front side bus, 6 spindles), I have to spend quite a bit more than we paid last year: $2K+, or nearly a 33% cost increase. This only brings a marginal increase in performance. The alternative to stay in budget is to take a hit on the fsb down to 800mhz or cut the number of cores in half, neither of which is attractive. The main cost culprit is the processor. IBM no longer offers the E5410. It's listed as a part, but not available in any of the server configs I've looked at. I'm considering getting the cheapest 800mhz fsb dual core xeon I can configure and then buying the E5410's separately. That's still an extra $350 I wasn't counting on, but that's better than $2K. I want to know what others think of this - will it work or will I end up with the wrong motherboard or some other issue? Am I missing a simple way to configure the server I really want? I don't really intend to do this, but one option to save some money back is to omit the redundant power supply. Since my redundancy plan for these system is to switch over to a completely different host, the extra power isn't fully necessary. That said, it's still very helpful to avoid even short downtimes while I switch over VMs. Has anyone done this?

  Read the article

• Mac Terminal.app: Force '^C' to be printed when editing current prompt, then aborting it

  - by Stefan Lasiewski

  This is the opposite of Prevent “^C” from being printed when aborting editing current prompt. I'm using Bash. When I'm editing the commandline in Bash, and I hit Control-C to abort the commandline, the '^C' character does not display. I would like to see this character. I tried commands like stty -ctlecho and stty ctlecho (which I borrowed from the other question), but this didn't work for me. This behavior seems to be true with my environment on Ubuntu, CentOS and MacOSX. This only happens within Apple's Terminal.App. If I SSH to a remote Linux or FreeBSD box, then ^C is printed. So, this is clearly just a local setting. Update: Here is the output of stty -a, as requested by @quack quixote : $ stty -a speed 9600 baud; 41 rows; 88 columns; lflags: icanon isig iexten echo echoe -echok echoke -echonl echoctl -echoprt -altwerase -noflsh -tostop -flusho pendin -nokerninfo -extproc iflags: -istrip icrnl -inlcr -igncr ixon -ixoff ixany imaxbel iutf8 -ignbrk brkint -inpck -ignpar -parmrk oflags: opost onlcr -oxtabs -onocr -onlret cflags: cread cs8 -parenb -parodd hupcl -clocal -cstopb -crtscts -dsrflow -dtrflow -mdmbuf cchars: discard = ^O; dsusp = ^Y; eof = ^D; eol = <undef>; eol2 = <undef>; erase = ^?; intr = ^C; kill = ^U; lnext = ^V; min = 1; quit = ^\; reprint = ^R; start = ^Q; status = ^T; stop = ^S; susp = ^Z; time = 0; werase = ^W; After typing stty sane, stty -a will output the following. The only difference is the parameter of -iutf8. $ stty sane $ stty -a speed 9600 baud; 41 rows; 157 columns; lflags: icanon isig iexten echo echoe -echok echoke -echonl echoctl -echoprt -altwerase -noflsh -tostop -flusho pendin -nokerninfo -extproc iflags: -istrip icrnl -inlcr -igncr ixon -ixoff ixany imaxbel -iutf8 -ignbrk brkint -inpck -ignpar -parmrk oflags: opost onlcr -oxtabs -onocr -onlret cflags: cread cs8 -parenb -parodd hupcl -clocal -cstopb -crtscts -dsrflow -dtrflow -mdmbuf cchars: discard = ^O; dsusp = ^Y; eof = ^D; eol = <undef>; eol2 = <undef>; erase = ^?; intr = ^C; kill = ^U; lnext = ^V; min = 1; quit = ^\; reprint = ^R; start = ^Q; status = ^T; stop = ^S; susp = ^Z; time = 0; werase = ^W;

  Read the article

• Exchange 2003-Exchange 2010 post migration GAL/OAB problem

  - by user68726

  I am very new to Exchange so forgive my newbie-ness. I've exhausted Google trying to find a way to solve my problem so I'm hoping some of you gurus can shed some light on my next steps. Please forgive my bungling around through this. The problem I cannot download/update the Global Address List (GAL) and Offline Address Book (OAB) on my Outlook 2010 clients. I get: Task 'emailaddress' reported error (0x8004010F) : 'The operation failed. An object cannot be found.' ---- error. I'm using cached exchange mode, which if I turn off Outlook hangs completely from the moment I start it up. (Note I've replaced my actual email address with 'emailaddress') Background information I migrated mailboxes, public store, etc. from a Small Business Server 2003 with Exchange 2003 box to a Server 2008 R2 with Exchange 2010 based primarily on an experts exchange how to article. The exchange server is up and running as an internet facing exchange server with all of the roles necessary to send and receive mail and in that capacity is working fine. I "thought" I had successfully migrated everything from the SBS03 box, and due to huge amounts of errors in everything from AD to the Exchange install itself I removed the reference to the SBS03 server in adsiedit. I've still got access to the old SBS03 box, but as I said the number of errors in everything is preventing even the uninstall of Exchange (or the starting of the Exchange Information Store service), so I'm quite content to leave that box completely out of the picture while trying to solve my problem. After research I discovered this is most likely because I failed to run the “update-globaladdresslist” (or get / update) command from the Exchange shell before I removed the Exchange 2003 server from adsiedit (and the network). If I run the command now it gives me: WARNING: The recipient "domainname.com/Microsoft Exchange System Objects/Offline Address Book - first administrative group" is invalid and couldn't be updated. WARNING: The recipient "domainname.com/Microsoft Exchange System Objects/Schedule+ Free Busy Information – first administrative group" is invalid and couldn't be updated. WARNING: The recipient "domainname.com/Microsoft Exchange System Objects/ContainernameArchive" is invalid and couldn't be updated. WARNING: The recipient "domainname.com/Microsoft Exchange System Objects/ContainernameContacts" is invalid and couldn't be updated. (Note that I’ve replaced my domain with “domainname.com” and my organization name with “containername”) What I’ve tried I don’t want to use the old OAB, or GAL, I don’t care about either, our GAL and distribution lists needed to be organized anyway, so at this point I really just want to get rid of the old reference to the “first administrative group” and move on. I’ve tried to create a new GAL and tell Exchange 2010 to use that GAL instead of the old GAL, but I'm obviously missing some of the commands or something dumb I need to do to start over with a blank slate/GAL/OAB. I'm very tempted to completely delete the entire "first administrative group" tree from adsiedit and see if that gets rid of the ridiculous reference that no longer exists but I dont want to break something else. Commands run to try to create a new GAL and tell exch10 to use that GAL: New-globaladdresslist –name NAMEOFNEWGAL Set-globaladdresslist GUID –name NAMEOFNEWGAL This did nothing for me except now when I run get-globaladdresslist or with the | FL pipe I see two GALs listed, the “default global address list” and the “NAMEOFNEWGAL” that I created. After a little more research this morning it looks like you can't change/delete/remove the default address list, and the only way to do what I'm trying to do would be to maybe remove the default address list via adsiedit and recreate with a command something like new-GlobalAddressList -Name "Default Global Address List" -IncludedRecipients AllRecipients. This would be acceptable but I've searched and searched and can't find instructions or a breakdown of where exactly the default GAL lives in AD, and if I'd have to remove multiple child references/records. Of interest I'm getting an event ID 9337 in my application log OALGen did not find any recipients in address list \Global Address List. This offline address list will not be generated. -\NAMEOFMYOAB --------- on my Exchange 2010 box, which pretty much to me seems to confirm my suspicion that the empty GAL/OAB is what's causing the Outlook client 0x8004010F error. Help please!

  Read the article

• Do email forms need to be santized before sending?

  - by levi

  I have a client that keeps getting reports from godaddy's "websiteprotection.com" stating how the website is insecure. Your website contains pages that do not properly sanitize visitor-provided input to make sure it contains no malicious content or scripts. Cross-site scripting vulnerabilities let malicious users execute arbitrary HTML or script code in another visitor's browser. Output: The request string used to detect this flaw was : /cross_site_scripting.?nasl.asp The output was : HTTP/1.1 404 Not Found\r Date: Wed, 21 Mar 2012 08:12:02 GMT\r Server: Apache\r X-Pingback:http://?CLIENTSWEBSITE.com/?xmlrpc.php\r Expires: Wed, 11 Jan 1984 05:00:00 GMT\r Cache-Control: no-cache, must-revalidate, max-age=0\r Pragma: no-cache\r Set-Cookie: PHPSESSID=?1jsnhuflvd59nb4trtquston50; path=/\r Last-Modified: Wed, 21 Mar 2012 08:12:02 GMT\r Keep-Alive: timeout=15, max=100\r Connection: Keep-Alive\r Transfer-Encoding: chunked\r Content-Type: text/html; charset=UTF-8\r \r <div id="contact-form" class="widget"><form action="http://?CLIENTSWEBSITE.c om/<script>cross_site_?scripting.nasl</script>.asp" id="contactForm" meth od="post"> It looks like it has an issue with the contact form. All the contact form does is posts an ajax request to the same page, and than a PHP script mails the data (no database stuff). Is there any a security issues here? Any ideas on how I can satisfy the security scanner? Here is the form and script: <form action="<?php echo $this->getCurrentUrl(); ?>" id="contactForm" method="post"> <input type="text" name="Name" id="Name" value="" class="txt requiredField name" /> //Some more text inputs <input type="hidden" name="sendadd" id="sendadd" value="<?php echo $emailadd ; ?>" /> <input type="hidden" name="submitted" id="submitted" value="true" /><input class="submit" type="submit" value="Send" /> </form> // Some initial JS validation, if that passes an ajax post is made to the script below //If the form is submitted if(isset($_POST['submitted'])) { //Check captcha if (isset($_POST["captchaPrefix"])) { $capt = new ReallySimpleCaptcha(); $correct = $capt->check( $_POST["captchaPrefix"], $_POST["Captcha"] ); if( ! $correct ) { echo false; die(); } else { $capt->remove( $_POST["captchaPrefix"] ); } } $dateon = $_POST["dateon"]; $ToEmail = $_POST["sendadd"]; $EmailSubject = 'Contact Form Submission from ' . get_bloginfo('title'); $mailheader = "From: ".$_POST["Email"]."\r\n"; $mailheader .= "Reply-To: ".$_POST["Email"]."\r\n"; $mailheader .= "Content-type: text/html; charset=iso-8859-1\r\n"; $MESSAGE_BODY = "Name: ".$_POST["Name"]."<br>"; $MESSAGE_BODY .= "Email Address: ".$_POST["Email"]."<br>"; $MESSAGE_BODY .= "Phone: ".$_POST["Phone"]."<br>"; if ($dateon == "on") {$MESSAGE_BODY .= "Date: ".$_POST["Date"]."<br>";} $MESSAGE_BODY .= "Message: ".$_POST["Comments"]."<br>"; mail($ToEmail, $EmailSubject, $MESSAGE_BODY, $mailheader) or die ("Failure"); echo true; die(); }

  Read the article

• what is the best mid/high-end class audio/music creation audio sound card?

  - by Chris

  Hello, I have a computershop myself, and I repair computers. But one of the things I really don't know (yet) is the performace od audio cards for music creation with midi. I have searched and searched and came up with some good reviews, but after browsing for a couple of hours I could't see the trees trough the forrest :-D (it's a dutch expression) At one moment I thought the M-Audio - Delta 1010LT would be a good PCIe card, later on I read that this card was released years ago. (but that could be false information) Also any personal expierence would be great, but not necessairy. I have searched a few cards, and I hope someone can help me make a choice for a friend of mine. He's buget is between $100 and $350 I know there are audio cards from $ 500 - $1850,- this is just too expensive. The following specs are crucial: ASIO Midi Mic in minimal 5.1, 7.1 recommended it's not for airplay, but just to compose music at home. using Ableton and midi keyboard. 1. M-Audio - Delta 1010LT: 8 x 8 analog I/O 2 mic preamps or line inputs S/PDIF digital I/O (coaxial) with 2-channel PCM SCMS copy protection control digital I/O supports surround-encoded AC-3 and DTS pass-through 1 x 1 MIDI I/O directly drive up to 7.1 surround (bass management software included) software controlled 36-bit internal DSP digital mixing/routing +4dbu/-10dBV operation individually switched in software word clock I/O for sample accurate device synchronization 2. RME HDSP 9632: * Stereo Analog Ein- und Ausgang, symmetrisch*, 24-Bit/192kHz, > 110 dB SNR * Optionale Erweiterungsboards mit je 4 symmetrischen Ein- und Ausgängen * Alle analogen I/Os voll 192 kHz-fähig, also keine Reduzierung der Kanalzahl * 1 x ADAT Digital In/Out, 96 kHz-fähig (S/MUX) * 1 x SPDIF Digital In/Out, 192 kHz-fähig * 1 x Breakout Kabel für koaxialen SPDIF-Betrieb* * Also bis zu 16 Ein-und Ausgänge gleichzeitig nutzbar! * 1 x Stereo Kopfhörerausgang, parallel zum analogen Ausgang, aber eigene Pegelanpassung * 1 x MIDI I/O für 16 Kanäle Hi-Speed MIDI über Breakout Kabel * DIGICheck, RMEs einzigartiges Meter- und Analysetool mit Spectral Analyser, Professionelle Level Meter 2/8/16-Kanalig, Vector Audio Scope und diversen weiteren Analysefunktionen * HDSP Meter Bridge: Frei skalierbare Levelmeter mit Peak- und RMS Berechnung in Hardware * TotalMix: 512-Kanal Mischer mit 40 Bit interner Auflösung 3. EMU 1212M (1212 M) PCIe: * Top kwaliteit convertors 24-bit/192kHz convertors. * Hardware gestuurde effecten. * DSP zero-latency hardware mixen en monitoring. * Analoge en digitale I/O plus MIDI. * EMU Production Tools Software Bundle - Cakewalk SONAR , Steinberg Cubase LE, Ableton Live E-MU Edition **EMU 1212M PCI-e inputs/outputs:** * 2 balanced jack inputs. * 2 balanced jack outputs. * 24-bit/192kHz ADAT I/O. * 24-bit/192kHz Coaxiale S/PDif I/O switchable to AES/EBU. * MIDI I/O. 4. M-Audio Audiophile 192: - Up to 24-bit/192kHz audio - 2 balanced analog inputs (1/4” TRS) - 2 balanced analog outputs (1/4” TRS) - S/PDIF digital I/O (coaxial RCA connectors) with 2-channel PCM - SCMS copy protection control - Digital I/O supports surround-encoded AC-3 and DTS pass-through - Direct hardware input monitoring via separate balanced 1/4” TRS monitor outputs - Software routing of inputs and outputs - Digital I/O can be routed to/from external effects - 16-channel MIDI I/O - ASIO, WDM, GSIF 2 and Core Audio driver support for compatibility with most applications - 64-bit driver support for Windows - PCI 2.2 compatibility - Apple G5 compatible - Incompatible exceptions - Includes Ableton Live Lite music production software, so you can make music right away - Works with other Delta cards Technical Specifcations: - Compatibility - ASIO - WDM - GSIF 2 - Core Audio

  Read the article

• Long connection times from PHP to MySQL on EC2

  - by Erik Giberti

  I'm having an intermittent issue connecting to a database slave with InnoDB. Intermittently I get connections taking longer than 2 seconds. These servers are hosted on Amazon's EC2. The app server is PHP 5.2/Apache running on Ubuntu. The DB slave is running Percona's XtraDB 5.1 on Ubuntu 9.10. It's using an EBS Raid array for the data storage. We already use skip name resolve and bind to address 0.0.0.0. This is a stub of the PHP code that's failing $tmp = mysqli_init(); $start_time = microtime(true); $tmp-options(MYSQLI_OPT_CONNECT_TIMEOUT, 2); $tmp-real_connect($DB_SERVERS[$server]['server'], $DB_SERVERS[$server]['username'], $DB_SERVERS[$server]['password'], $DB_SERVERS[$server]['schema'], $DB_SERVERS[$server]['port']); if(mysqli_connect_errno()){ $timer = microtime(true) - $start_time; mail($errors_to,'DB connection error',$timer); } There's more than 300Mb available on the DB server for new connections and the server is nowhere near the max allowed (60 of 1,200). Loading on both servers is < 2 on 4 core m1.xlarge instances. Some highlights from the mysql config max_connections = 1200 thread_stack = 512K thread_cache_size = 1024 thread_concurrency = 16 innodb-file-per-table innodb_additional_mem_pool_size = 16M innodb_buffer_pool_size = 13G Any help on tracing the source of the slowdown is appreciated. [EDIT] I have been updating the sysctl values for the network but they don't seem to be fixing the problem. I made the following adjustments on both the database and application servers. net.ipv4.tcp_window_scaling = 1 net.ipv4.tcp_sack = 0 net.ipv4.tcp_timestamps = 0 net.ipv4.tcp_fin_timeout = 20 net.ipv4.tcp_keepalive_time = 180 net.ipv4.tcp_max_syn_backlog = 1280 net.ipv4.tcp_synack_retries = 1 net.core.rmem_max = 16777216 net.core.wmem_max = 16777216 net.ipv4.tcp_rmem = 4096 87380 16777216 net.ipv4.tcp_wmem = 4096 87380 16777216 [EDIT] Per jaimieb's suggestion, I added some tracing and captured the following data using time. This server handles about 51 queries/second at this the time of day. The connection error was raised once (at 13:06:36) during the 3 minute window outlined below. Since there was 1 failure and roughly 9,200 successful connections, I think this isn't going to produce anything meaningful in terms of reporting. Script: date /root/database_server.txt (time mysql -h database_Server -D schema_name -u appuser -p apppassword -e '') /dev/null 2 /root/database_server.txt Results: === Application Server 1 === Mon Feb 22 13:05:01 EST 2010 real 0m0.008s user 0m0.001s sys 0m0.000s Mon Feb 22 13:06:01 EST 2010 real 0m0.007s user 0m0.002s sys 0m0.000s Mon Feb 22 13:07:01 EST 2010 real 0m0.008s user 0m0.000s sys 0m0.001s === Application Server 2 === Mon Feb 22 13:05:01 EST 2010 real 0m0.009s user 0m0.000s sys 0m0.002s Mon Feb 22 13:06:01 EST 2010 real 0m0.009s user 0m0.001s sys 0m0.003s Mon Feb 22 13:07:01 EST 2010 real 0m0.008s user 0m0.000s sys 0m0.001s === Database Server === Mon Feb 22 13:05:01 EST 2010 real 0m0.016s user 0m0.000s sys 0m0.010s Mon Feb 22 13:06:01 EST 2010 real 0m0.006s user 0m0.010s sys 0m0.000s Mon Feb 22 13:07:01 EST 2010 real 0m0.016s user 0m0.000s sys 0m0.010s [EDIT] Per a suggestion received on a LinkedIn question, I tried setting the back_log value higher. We had been running the default value (50) and increased it to 150. We also raised the kernel value /proc/sys/net/core/somaxconn (maximum socket connections) to 256 on both the application and database server from the default 128. We did see some elevation in processor utilization as a result but still received connection timeouts.

  Read the article

• Centos 7. Freeradius fails to start on boot

  - by Alex

  I was messing around with FreeRADIUS and MySQL (MariaDB) and it seems FreeRADIUS service can't start properly on startup. But it starts fine using root user or in debug mode (radiusd -X) and works just fine! Debug mode shows no errors. systemctl command shows that radiusd.service has failed to start. /var/log/messages output: Aug 21 15:52:29 nexus-test systemd: Starting The Apache HTTP Server... Aug 21 15:52:29 nexus-test systemd: Starting MariaDB database server... Aug 21 15:52:29 nexus-test systemd: Starting FreeRADIUS high performance RADIUS server.... Aug 21 15:52:29 nexus-test systemd: Started OpenSSH server daemon. Aug 21 15:52:29 nexus-test mysqld_safe: 140821 15:52:29 mysqld_safe Logging to '/var/log/mariadb/mariadb.log'. Aug 21 15:52:29 nexus-test mysqld_safe: 140821 15:52:29 mysqld_safe Starting mysqld daemon with databases from /var/lib/mysql Aug 21 15:52:30 nexus-test systemd: Started Postfix Mail Transport Agent. Aug 21 15:52:30 nexus-test avahi-daemon[604]: Registering new address record for fe80::250:56ff:fe85:e4af on eth0.*. Aug 21 15:52:30 nexus-test systemd: radiusd.service: control process exited, code=exited status=1 Aug 21 15:52:30 nexus-test systemd: Failed to start FreeRADIUS high performance RADIUS server.. Aug 21 15:52:30 nexus-test systemd: Unit radiusd.service entered failed state. Aug 21 15:52:31 nexus-test kdumpctl: kexec: loaded kdump kernel Aug 21 15:52:31 nexus-test kdumpctl: Starting kdump: [OK] Aug 21 15:52:31 nexus-test systemd: Started Crash recovery kernel arming. Aug 21 15:52:31 nexus-test systemd: Started The Apache HTTP Server. Aug 21 15:52:31 nexus-test systemd: Started MariaDB database server. /var/log/radius/radius.log output: Thu Aug 21 15:24:16 2014 : Info: rlm_sql (sql): Driver rlm_sql_mysql (module rlm_sql_mysql) loaded and linked Thu Aug 21 15:24:16 2014 : Info: rlm_sql (sql): Attempting to connect to database "radius" Thu Aug 21 15:24:16 2014 : Info: rlm_sql (sql): Opening additional connection (0) Thu Aug 21 15:24:16 2014 : Error: rlm_sql_mysql: Couldn't connect socket to MySQL server radius@localhost:radius Thu Aug 21 15:24:16 2014 : Error: rlm_sql_mysql: Mysql error 'Can't connect to local MySQL server through socket '/var/lib/mysql/mysql.sock' (2)' Thu Aug 21 15:24:16 2014 : Error: rlm_sql (sql): Opening connection failed (0) Thu Aug 21 15:24:16 2014 : Error: /etc/raddb/mods-enabled/sql[47]: Instantiation failed for module "sql" After seeing this I tried to replicate the problem, killed mariadb.service and started to run debug mode again. And it spits out the same problem as in the radius.log. I tried disabling iptables and firewalld and rebooting, but no luck: systemctl disable iptables systemctl disable firewalld So maybe the problem is in the process startup order or delay of some kind. Maybe FreeRADIUS's SQL module can't connect to not yet started MariaDB? If it, how can I fix this? In earlier versions of RHEL/CENTOS I know you easily see service start order in like rc.d or stuff, now IDK. I am new to this fancy "systemd", "systemctl", "firewalld" stuff Centos 7 introduced so sorry I'm a little bit confused. Also this new FreeRADIUS 3 structure... PS. MariaDB is enabled on startup, credentials in FR DB configuration are correct A little update: cat /etc/systemd/system/multi-user.target.wants/radiusd.service output: [Unit] Description=FreeRADIUS high performance RADIUS server. After=syslog.target network.target [Service] Type=forking PIDFile=/var/run/radiusd/radiusd.pid ExecStartPre=-/bin/chown -R radiusd.radiusd /var/run/radiusd ExecStartPre=/usr/sbin/radiusd -C ExecStart=/usr/sbin/radiusd -d /etc/raddb ExecReload=/usr/sbin/radiusd -C ExecReload=/bin/kill -HUP $MAINPID [Install] WantedBy=multi-user.target

  Read the article

• Is it possible to write C# code as below and send email using network in different country?

  - by kedar karthik

  Is it possible to write C# code as below and send email using mnetwork in different country? MSExchangeWebServiceURL = mail.something.com/ews/exchange.asmx its a web service URL ... sorry to correct my self //....this works great when i run the same code from home network, my friends home network ... anywhere around ... but when i run it from my clients location in columbia ... it fails I have a valid user name and password on that exchange server. Is there any configuration that I can set to achieve this? BTW this code below works when I run it within office network and any network within any home network ... i have tried atleast 5 friends network in Plano, Texas. I want this code to work when run from any network in another country. My client in columbia can connect to web service using a browser .. use the same user name and password ..... but when i run the code above ... it is not able to connect to our web service .... String cMSExchangeWebServiceURL = (String)System.Configuration.ConfigurationSettings.AppSettings["MSExchangeWebServiceURL"]; String cEmail = (String)System.Configuration.ConfigurationSettings.AppSettings["Cemail"]; String cPassword = (String)System.Configuration.ConfigurationSettings.AppSettings["Cpassword"]; String cTo = (String)System.Configuration.ConfigurationSettings.AppSettings["CTo"]; ExchangeServiceBinding esb = new ExchangeServiceBinding(); esb.Timeout = 1800000; esb.AllowAutoRedirect = true; esb.UseDefaultCredentials = false; esb.Credentials = new NetworkCredential(cEmail, cPassword); esb.Url = cMSExchangeWebServiceURL; ServicePointManager.ServerCertificateValidationCallback += delegate(object sender1, X509Certificate certificate, X509Chain chain, SslPolicyErrors sslPolicyErrors) { return true; }; // Create a CreateItem request object CreateItemType request = new CreateItemType(); // Setup the request: // Indicate that we only want to send the message. No copy will be saved. request.MessageDisposition = MessageDispositionType.SendOnly; request.MessageDispositionSpecified = true; // Create a message object and set its properties MessageType message = new MessageType(); message.Subject = subject; message.Body = new TestOutgoingEmailServer.com.cogniti.mail1.BodyType(); message.Body.BodyType1 = BodyTypeType.HTML; message.Body.Value = body; message.ToRecipients = new EmailAddressType[3]; message.ToRecipients[0] = new EmailAddressType(); //message.ToRecipients[1] = new EmailAddressType(); //message.ToRecipients[2] = new EmailAddressType(); message.ToRecipients[0].EmailAddress = "[email protected]"; message.ToRecipients[0].RoutingType = "SMTP"; //message.CcRecipients = new EmailAddressType[1]; //message.CcRecipients[0] = new EmailAddressType(); //message.CcRecipients[0].EmailAddress = toEmailAddress.ElementAt(1).ToString(); //message.CcRecipients[0].RoutingType = "SMTP"; //There are some more properties in MessageType object //you can set all according to your requirement // Construct the array of items to send request.Items = new NonEmptyArrayOfAllItemsType(); request.Items.Items = new ItemType[1]; request.Items.Items[0] = message; // Call the CreateItem EWS method. CreateItemResponseType response = esb.CreateItem(request);

  Read the article

• How Hacker Can Access VPS CentOS 6 content?

  - by user2118559

  Just want to understand. Please, correct mistakes and write advices Hacker can access to VPS: 1. Through (using) console terminal, for example, using PuTTY. To access, hacker need to know port number, username and password. Port number hacker can know scanning open ports and try to login. The only way to login as I understand need to know username and password. To block (make more difficult) port scanning, need to use iptables configure /etc/sysconfig/iptables. I followed this https://www.digitalocean.com/community/articles/how-to-setup-a-basic-ip-tables-configuration-on-centos-6 tutorial and got *nat :PREROUTING ACCEPT [87:4524] :POSTROUTING ACCEPT [77:4713] :OUTPUT ACCEPT [77:4713] COMMIT *mangle :PREROUTING ACCEPT [2358:200388] :INPUT ACCEPT [2358:200388] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [2638:477779] :POSTROUTING ACCEPT [2638:477779] COMMIT *filter :INPUT DROP [1:40] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [339:56132] -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m tcp --tcp-flags FIN,SYN,RST,PSH,ACK,URG NONE -j DROP -A INPUT -p tcp -m tcp ! --tcp-flags FIN,SYN,RST,ACK SYN -m state --state NEW -j DROP -A INPUT -p tcp -m tcp --tcp-flags FIN,SYN,RST,PSH,ACK,URG FIN,SYN,RST,PSH,ACK,URG -j DROP -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -p tcp -m tcp --dport 110 -j ACCEPT -A INPUT -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT -s 11.111.11.111/32 -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT -p tcp -m tcp --dport 21 -j ACCEPT -A INPUT -s 11.111.11.111/32 -p tcp -m tcp --dport 21 -j ACCEPT COMMIT Regarding ports that need to be opened. If does not use ssl, then seems must leave open port 80 for website. Then for ssh (default 22) and for ftp (default 21). And set ip address, from which can connect. So if hacker uses other ip address, he can not access even knowing username and password? Regarding emails not sure. If I send email, using Gmail (Send mail as: (Use Gmail to send from your other email addresses)), then port 25 not necessary. For incoming emails at dynadot.com I use Email Forwarding. Does it mean that emails “does not arrive to VPS” (before arriving to VPS, emails are forwarded, for example to Gmail)? If emails does not arrive to VPS, then seems port 110 also not necessary. If use only ssl, must open port 443 and close port 80. Do not understand regarding port 3306 In PuTTY with /bin/netstat -lnp see Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN 992/mysqld As understand it is for mysql. But does not remember that I have opened such port (may be when installed mysql, the port is opened automatically?). Mysql is installed on the same server, where all other content. Need to understand regarding port 3306 2. Also hacker may be able access console terminal through VPS hosting provider Control Panel (serial console emergency access). As understand only using console terminal (PuTTY, etc.) can make “global” changes (changes that can not modify with ftp). 3. Hacker can access to my VPS exploiting some hole in my php code and uploading, for example, Trojan. Unfortunately, faced situation that VPS was hacked. As understand it was because I used ZPanel. On VPS ( \etc\zpanel\panel\bin) ) found one php file, that was identified as Trojan by some virus scanners (at virustotal.com). Experimented with the file on local computer (wamp). And appears that hacker can see all content of VPS, rename, delete, upload etc. From my opinion, if in PuTTY use command like chattr +i /etc/php.ini then hacker could not be able to modify php.ini. Is there any other way to get into VPS?

  Read the article

• Rsyslog is not working properly, it does not log anything

  - by Victor Henriquez

  I'm running a Debian server and a couple of days ago my rsyslog started to behave very weird, the daemon is running but it doesn't seem to do anything. Many people use the system but I'm the only one with (legal) root access. I'm using the default rsyslogd configuration (if you think is relevant I'll attach it, but it's the one that comes with the package). After I rotated all the log files, they have remained empty: # ls -l /var/log/*.log -rw-r--r-- 1 root root 0 Jun 27 00:25 /var/log/alternatives.log -rw-r----- 1 root adm 0 Jun 26 13:03 /var/log/auth.log -rw-r----- 1 root adm 0 Jun 26 13:03 /var/log/daemon.log -rw-r--r-- 1 root root 0 Jun 27 00:25 /var/log/dpkg.log -rw-r----- 1 root adm 0 Jun 26 13:03 /var/log/kern.log -rw-r----- 1 root adm 0 Jun 26 13:03 /var/log/lpr.log -rw-r----- 1 root adm 0 Jun 26 13:03 /var/log/mail.log -rw-r----- 1 root adm 0 Jun 26 13:03 /var/log/user.log Any try to force a log writing does not have any effect: # logger hey # ls -l /var/log/messages -rw-r----- 1 root adm 0 Jun 26 13:03 /var/log/messages Lsof shows that rsyslogd does not have any log files opened: # lsof -p 1855 COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME rsyslogd 1855 root cwd DIR 202,0 4096 2 / rsyslogd 1855 root rtd DIR 202,0 4096 2 / rsyslogd 1855 root txt REG 202,0 342076 21649 /usr/sbin/rsyslogd rsyslogd 1855 root mem REG 202,0 38556 32153 /lib/i386-linux-gnu/i686/cmov/libnss_nis-2.13.so rsyslogd 1855 root mem REG 202,0 79728 32165 /lib/i386-linux-gnu/i686/cmov/libnsl-2.13.so rsyslogd 1855 root mem REG 202,0 26456 32163 /lib/i386-linux-gnu/i686/cmov/libnss_compat-2.13.so rsyslogd 1855 root mem REG 202,0 297500 1061058 /usr/lib/rsyslog/imuxsock.so rsyslogd 1855 root mem REG 202,0 42628 32170 /lib/i386-linux-gnu/i686/cmov/libnss_files-2.13.so rsyslogd 1855 root mem REG 202,0 22784 1061106 /usr/lib/rsyslog/imklog.so rsyslogd 1855 root mem REG 202,0 1401000 32169 /lib/i386-linux-gnu/i686/cmov/libc-2.13.so rsyslogd 1855 root mem REG 202,0 30684 32175 /lib/i386-linux-gnu/i686/cmov/librt-2.13.so rsyslogd 1855 root mem REG 202,0 9844 32157 /lib/i386-linux-gnu/i686/cmov/libdl-2.13.so rsyslogd 1855 root mem REG 202,0 117009 32154 /lib/i386-linux-gnu/i686/cmov/libpthread-2.13.so rsyslogd 1855 root mem REG 202,0 79980 17746 /usr/lib/libz.so.1.2.3.4 rsyslogd 1855 root mem REG 202,0 18836 1061094 /usr/lib/rsyslog/lmnet.so rsyslogd 1855 root mem REG 202,0 117960 31845 /lib/i386-linux-gnu/ld-2.13.so rsyslogd 1855 root 0u unix 0xebe8e800 0t0 640 /dev/log rsyslogd 1855 root 3u FIFO 0,5 0t0 2474 /dev/xconsole rsyslogd 1855 root 4u unix 0xebe8e400 0t0 645 /var/spool/postfix/dev/log rsyslogd 1855 root 5r REG 0,3 0 4026532176 /proc/kmsg I was so frustrated that even reinstall the rsyslog package, but it still refuses to log anything: # apt-get remove --purge rsyslog # apt-get install rsyslog I thought someone had hacked the system, so run rkhunter, chkrootkit, unhide in an attempt to find hide processes / ports and nmap in a remote host to compare with the ports shown by netstat. And I know this doesn't mean anything, but all looks ok. The system also have an iptables firewall that is very restrictive with incoming / outgoing connections. This is driving me crazy, any idea what is going on here? [EDIT - disk space info] # df -h Filesystem Size Used Avail Use% Mounted on rootfs 24G 22G 629M 98% / /dev/root 24G 22G 629M 98% / devtmpfs 10M 112K 9.9M 2% /dev tmpfs 76M 48K 76M 1% /run tmpfs 5.0M 0 5.0M 0% /run/lock tmpfs 151M 40K 151M 1% /tmp tmpfs 151M 0 151M 0% /run/shm

  Read the article

• MX records not correctly updated by the Google DNS servers

  - by Mac_Cain13

  We are currently losing some e-mail and we discovered that this is caused by a wrong DNS setting. We used a CNAME for our MX record an thats not allowed. So about 2 weeks ago we changed it to an A-record to fix the problem. It seems all major DNS services (like OpenDNS and ISPs) have synced their records and are returning correct results on our DNS queries. But Googles DNS service (at 8.8.8.8) is still returning the CNAME values and we still some e-mails are not delivered correctly. Query on OpenDNS: ; <<>> DiG 9.7.3-P3 <<>> mx wrep.nl @208.67.222.222 ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 51231 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;wrep.nl. IN MX ;; ANSWER SECTION: wrep.nl. 3595 IN MX 10 druif.wrep.nl. ;; Query time: 21 msec ;; SERVER: 208.67.222.222#53(208.67.222.222) ;; WHEN: Fri Nov 25 21:36:58 2011 ;; MSG SIZE rcvd: 47 Query on Google DNS: ; <<>> DiG 9.7.3-P3 <<>> mx wrep.nl @8.8.8.8 ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 12124 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 1, ADDITIONAL: 0 ;; QUESTION SECTION: ;wrep.nl. IN MX ;; ANSWER SECTION: wrep.nl. 2372 IN CNAME druif.wrep.nl. ;; AUTHORITY SECTION: wrep.nl. 572 IN SOA ns0.freshdns.nl. hostmaster.twilightinc.nl. 2011112401 14400 3600 604800 3600 ;; Query time: 94 msec ;; SERVER: 8.8.8.8#53(8.8.8.8) ;; WHEN: Fri Nov 25 21:38:10 2011 ;; MSG SIZE rcvd: 117 So is there anyone who can explain why Google is responding with a different (incorrect) result two weeks after the last change? And how can we get Google to update their DNS records correctly? Any help is very appreciated. (Please note that other domains that are managed by the same DNS servers/tools are working fine.)

  Read the article

• How to setup stunnel so that gmail can use my own smtp server to send messages.

  - by igorhvr

  I am trying to setup gmail to send messages using my own smtp server. I am doing this by using stunnel over a non-ssl enabled server. I am able to use my own smtp client with ssl enabled just fine to my server. Unfortunately, however, gmail seems to be unable to connect to my stunnel port. Gmail seems to be simply closing the connection right after it is established - I get a "SSL socket closed on SSL_read" on my server logs. On gmail, I get a "We are having trouble authenticating with your other mail service. Please try changing your SSL settings. If you continue to experience difficulties, please contact your other email provider for further instructions." message. Any help / tips on figuring this out will be appreciated. My certificate is self-signed - could this perhaps be related to the problem I am experiencing? I pasted the entire SSL session (logs from my server) below. 2011.01.02 16:56:20 LOG7[20897:3082491584]: Service ssmtp accepted FD=0 from 209.85.210.171:46858 2011.01.02 16:56:20 LOG7[20897:3082267504]: Service ssmtp started 2011.01.02 16:56:20 LOG7[20897:3082267504]: FD=0 in non-blocking mode 2011.01.02 16:56:20 LOG7[20897:3082267504]: Option TCP_NODELAY set on local socket 2011.01.02 16:56:20 LOG7[20897:3082267504]: Waiting for a libwrap process 2011.01.02 16:56:20 LOG7[20897:3082267504]: Acquired libwrap process #0 2011.01.02 16:56:20 LOG7[20897:3082267504]: Releasing libwrap process #0 2011.01.02 16:56:20 LOG7[20897:3082267504]: Released libwrap process #0 2011.01.02 16:56:20 LOG7[20897:3082267504]: Service ssmtp permitted by libwrap from 209.85.210.171:46858 2011.01.02 16:56:20 LOG5[20897:3082267504]: Service ssmtp accepted connection from 209.85.210.171:46858 2011.01.02 16:56:20 LOG7[20897:3082267504]: FD=1 in non-blocking mode 2011.01.02 16:56:20 LOG6[20897:3082267504]: connect_blocking: connecting 127.0.0.1:25 2011.01.02 16:56:20 LOG7[20897:3082267504]: connect_blocking: s_poll_wait 127.0.0.1:25: waiting 10 seconds 2011.01.02 16:56:20 LOG5[20897:3082267504]: connect_blocking: connected 127.0.0.1:25 2011.01.02 16:56:20 LOG5[20897:3082267504]: Service ssmtp connected remote server from 127.0.0.1:3701 2011.01.02 16:56:20 LOG7[20897:3082267504]: Remote FD=1 initialized 2011.01.02 16:56:20 LOG7[20897:3082267504]: Option TCP_NODELAY set on remote socket 2011.01.02 16:56:20 LOG5[20897:3082267504]: Negotiations for smtp (server side) started 2011.01.02 16:56:20 LOG7[20897:3082267504]: RFC 2487 not detected 2011.01.02 16:56:20 LOG5[20897:3082267504]: Protocol negotiations succeeded 2011.01.02 16:56:20 LOG7[20897:3082267504]: SSL state (accept): before/accept initialization 2011.01.02 16:56:20 LOG7[20897:3082267504]: SSL state (accept): SSLv3 read client hello A 2011.01.02 16:56:20 LOG7[20897:3082267504]: SSL state (accept): SSLv3 write server hello A 2011.01.02 16:56:20 LOG7[20897:3082267504]: SSL state (accept): SSLv3 write certificate A 2011.01.02 16:56:20 LOG7[20897:3082267504]: SSL state (accept): SSLv3 write certificate request A 2011.01.02 16:56:20 LOG7[20897:3082267504]: SSL state (accept): SSLv3 flush data 2011.01.02 16:56:20 LOG5[20897:3082267504]: CRL: verification passed 2011.01.02 16:56:20 LOG5[20897:3082267504]: VERIFY OK: depth=2, /C=US/O=Equifax/OU=Equifax Secure Certificate Authority 2011.01.02 16:56:20 LOG5[20897:3082267504]: CRL: verification passed 2011.01.02 16:56:20 LOG5[20897:3082267504]: VERIFY OK: depth=1, /C=US/O=Google Inc/CN=Google Internet Authority 2011.01.02 16:56:20 LOG5[20897:3082267504]: CRL: verification passed 2011.01.02 16:56:20 LOG5[20897:3082267504]: VERIFY OK: depth=0, /C=US/ST=California/L=Mountain View/O=Google Inc/CN=smtp.gmail.com 2011.01.02 16:56:20 LOG7[20897:3082267504]: SSL state (accept): SSLv3 read client certificate A 2011.01.02 16:56:20 LOG7[20897:3082267504]: SSL state (accept): SSLv3 read client key exchange A 2011.01.02 16:56:20 LOG7[20897:3082267504]: SSL state (accept): SSLv3 read certificate verify A 2011.01.02 16:56:20 LOG7[20897:3082267504]: SSL state (accept): SSLv3 read finished A 2011.01.02 16:56:20 LOG7[20897:3082267504]: SSL state (accept): SSLv3 write change cipher spec A 2011.01.02 16:56:20 LOG7[20897:3082267504]: SSL state (accept): SSLv3 write finished A 2011.01.02 16:56:20 LOG7[20897:3082267504]: SSL state (accept): SSLv3 flush data 2011.01.02 16:56:20 LOG7[20897:3082267504]: 1 items in the session cache 2011.01.02 16:56:20 LOG7[20897:3082267504]: 0 client connects (SSL_connect()) 2011.01.02 16:56:20 LOG7[20897:3082267504]: 0 client connects that finished 2011.01.02 16:56:20 LOG7[20897:3082267504]: 0 client renegotiations requested 2011.01.02 16:56:20 LOG7[20897:3082267504]: 1 server connects (SSL_accept()) 2011.01.02 16:56:20 LOG7[20897:3082267504]: 1 server connects that finished 2011.01.02 16:56:20 LOG7[20897:3082267504]: 0 server renegotiations requested 2011.01.02 16:56:20 LOG7[20897:3082267504]: 0 session cache hits 2011.01.02 16:56:20 LOG7[20897:3082267504]: 0 external session cache hits 2011.01.02 16:56:20 LOG7[20897:3082267504]: 0 session cache misses 2011.01.02 16:56:20 LOG7[20897:3082267504]: 0 session cache timeouts 2011.01.02 16:56:20 LOG6[20897:3082267504]: SSL accepted: new session negotiated 2011.01.02 16:56:20 LOG6[20897:3082267504]: Negotiated ciphers: RC4-MD5 SSLv3 Kx=RSA Au=RSA Enc=RC4(128) Mac=MD5 2011.01.02 16:56:20 LOG7[20897:3082267504]: SSL socket closed on SSL_read 2011.01.02 16:56:20 LOG7[20897:3082267504]: Socket write shutdown 2011.01.02 16:56:20 LOG5[20897:3082267504]: Connection closed: 167 bytes sent to SSL, 37 bytes sent to socket 2011.01.02 16:56:20 LOG7[20897:3082267504]: Service ssmtp finished (0 left)

  Read the article

• All my sites are 403 but the server is running. Errors on startup

  - by Craig

  We gave access to a contractor to install a firewall and somehow while he was doing it he fracked something up. Everything went off-line about 24 hours ago and we are effectively out of business until I solve this and the person who messed up the thing is not returning calls. I found a few errors. First, I'm not a server guy - I can look at log files and normally everything runs fine. All 'services' are running according to 1and1 server monitoring and mail is being delivered just fine. The whole thing was off-line until I (probably stupidly) updated the kernel from 6.2 to 6.3 this morning and I got everything back except the http access. All the domains (~200 of them) are returning a 403 error and nothing is recorded in the access log. On every restart I see this error in the messages log file: init: Failed to spawn ttyS0 main process: unable to execute: No such file or directory and a little later these: kernel: WARNING: at kernel/sched.c:5914 thread_return+0x232/0x79d() (Not tainted) kernel: Hardware name: X9SCL/X9SCM kernel: Modules linked in: xt_iprange iptable_filter ip_tables ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables ipv6 ext4 jbd2 serio_raw i2c_i801 i2c_core sg iTCO_wdt iTCO_vendor_support e1000e ext3 jbd mbcache raid1 sd_mod crc_t10dif ahci dm_mirror dm_region_hash dm_log dm_mod [last unloaded: scsi_wait_scan] kernel: Pid: 367, comm: md3_raid1 Not tainted 2.6.32-220.2.1.el6.x86_64 #1 kernel: Call Trace: kernel: [<ffffffff81069997>] ? warn_slowpath_common+0x87/0xc0 kernel: [<ffffffff810699ea>] ? warn_slowpath_null+0x1a/0x20 kernel: [<ffffffff814eccc5>] ? thread_return+0x232/0x79d kernel: [<ffffffff8126a4d9>] ? cpumask_next_and+0x29/0x50 kernel: [<ffffffff813e9c05>] ? md_super_wait+0x55/0x90 kernel: [<ffffffff81090a10>] ? autoremove_wake_function+0x0/0x40 kernel: [<ffffffff813ebf46>] ? md_update_sb+0x206/0x3f0 kernel: [<ffffffff813ee922>] ? md_check_recovery+0x3f2/0x6d0 kernel: [<ffffffffa005b129>] ? raid1d+0x49/0x1050 [raid1] kernel: [<ffffffff814ed985>] ? schedule_timeout+0x215/0x2e0 kernel: [<ffffffff814ef447>] ? _spin_unlock_irqrestore+0x17/0x20 kernel: [<ffffffff813eb336>] ? md_thread+0x116/0x150 kernel: [<ffffffff81090a10>] ? autoremove_wake_function+0x0/0x40 kernel: [<ffffffff813eb220>] ? md_thread+0x0/0x150 kernel: [<ffffffff810906a6>] ? kthread+0x96/0xa0 kernel: [<ffffffff8100c14a>] ? child_rip+0xa/0x20 kernel: [<ffffffff81090610>] ? kthread+0x0/0xa0 kernel: [<ffffffff8100c140>] ? child_rip+0x0/0x20 And something is wrong with the Named/BIND resulting in the same error for all domains: zone DOMAINEXAMPLE.com/IN: loading from master file DOMAINEXAMPLE.com failed: file not found zone DOMAINEXAMPLE.com/IN: not loaded due to errors. _default/DOMAINEXAMPLE.com/IN: file not found I'm pretty sure this is not enough information to solve the problem, but I'm willing to engage someone who can work this out for me. Any help would be greatly appreciated.

  Read the article

• Can't re-mount existing RAID10 on Ubuntu

  - by Zoran

  I saw similar questions, but didn't find what solution to my problem. After power-cut, one of RAID10 (4 disks were) appears to be malfunctioning. I make tha array active one, but can not mount it. Always the same error: mount: you must specify the filesystem type So, here is what I have when type mdadm --detail /dev/md0 /dev/md0: Version : 00.90.03 Creation Time : Tue Sep 1 11:00:40 2009 Raid Level : raid10 Array Size : 1465148928 (1397.27 GiB 1500.31 GB) Used Dev Size : 732574464 (698.64 GiB 750.16 GB) Raid Devices : 4 Total Devices : 3 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Mon Jun 11 09:54:27 2012 State : clean, degraded Active Devices : 3 Working Devices : 3 Failed Devices : 0 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K UUID : 1a02e789:c34377a1:2e29483d:f114274d Events : 0.166 Number Major Minor RaidDevice State 0 8 16 0 active sync /dev/sdb 1 0 0 1 removed 2 8 48 2 active sync /dev/sdd 3 8 64 3 active sync /dev/sde At the /etc/mdadm/mdadm.conf I have by default, scan all partitions (/proc/partitions) for MD superblocks. alternatively, specify devices to scan, using wildcards if desired. DEVICE partitions auto-create devices with Debian standard permissions CREATE owner=root group=disk mode=0660 auto=yes automatically tag new arrays as belonging to the local system HOMEHOST <system> instruct the monitoring daemon where to send mail alerts MAILADDR root definitions of existing MD arrays ARRAY /dev/md0 level=raid10 num-devices=4 UUID=1a02e789:c34377a1:2e29483d:f114274d ARRAY /dev/md1 level=raid1 num-devices=2 UUID=9b592be7:c6a2052f:2e29483d:f114274d This file was auto-generated... So, my question is, how can I mount md0 array (md1 has been mounted without problem) in order to preserve existing data? One more thing, fdisk -l command gives the following result: Disk /dev/sdb: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x660a6799 Device Boot Start End Blocks Id System /dev/sdb1 * 1 88217 708603021 83 Linux /dev/sdb2 88218 91201 23968980 5 Extended /dev/sdb5 88218 91201 23968948+ 82 Linux swap / Solaris Disk /dev/sdc: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x0008f8ae Device Boot Start End Blocks Id System /dev/sdc1 1 88217 708603021 83 Linux /dev/sdc2 88218 91201 23968980 5 Extended /dev/sdc5 88218 91201 23968948+ 82 Linux swap / Solaris Disk /dev/sdd: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x4be1abdb Device Boot Start End Blocks Id System Disk /dev/sde: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xa4d5632e Device Boot Start End Blocks Id System Disk /dev/sdf: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xdacb141c Device Boot Start End Blocks Id System Disk /dev/sdg: 750.1 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xdacb141c Device Boot Start End Blocks Id System Disk /dev/md1: 750.1 GB, 750156251136 bytes 2 heads, 4 sectors/track, 183143616 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk identifier: 0xdacb141c Device Boot Start End Blocks Id System Warning: ignoring extra data in partition table 5 Warning: ignoring extra data in partition table 5 Warning: ignoring extra data in partition table 5 Warning: invalid flag 0x7b6e of partition table 5 will be corrected by w(rite) Disk /dev/md0: 1500.3 GB, 1500312502272 bytes 255 heads, 63 sectors/track, 182402 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x660a6799 Device Boot Start End Blocks Id System /dev/md0p1 * 1 88217 708603021 83 Linux /dev/md0p2 88218 91201 23968980 5 Extended /dev/md0p5 ? 121767 155317 269488144 20 Unknown And one more thing. When using mdadm --examine command, here ise result: mdadm -v --examine --scan /dev/sdb /dev/sdc /dev/sdd /dev/sde /dev/sdf /dev/sd ARRAY /dev/md1 level=raid1 num-devices=2 UUID=9b592be7:c6a2052f:2e29483d:f114274d devices=/dev/sdf ARRAY /dev/md0 level=raid10 num-devices=4 UUID=1a02e789:c34377a1:2e29483d:f114274d devices=/dev/sdb,/dev/sdc,/dev/sdd,/dev/sde md0 has 3 devices which are active. Can someone instruct me how to solve this issue? If it is possible, I would like not to removing faulty HDD. Please advise

  Read the article

• Can not access network computers anymore

  - by Johny Skovdal

  Last Thursday (03/05/12) I got a new computer to be able to work from home. I plugged it, by cable, into the company network and installed most of the software needed for me to do so, by accessing a share on my stationary computer at work. I had no issues here what so ever, and everything just worked. Yesterday evening I tried accessing the company network trough Windows VPN, and while I was able to connect to the network, I was unable to connect to any computers on the network. I did, however, get an error when connecting, but I can't seem to get the error again, to get the details of the error message. Today I am sitting on the company network again, and now I can not access anything on the network like I could last Thursday, though I can ping all the computers I am attempting to access. Here is a list of details that might help in troubleshooting this issue (updated): List of observations / actions My computer is identical to another computer that has no issues. It is not on the domain but rather on the default workgroup, but this was not an issue last Thursday, so I am assuming it still is not. I am able to access my e-mail on the exchange server. I can connect to our TFS server from Visual Studio but not from Explorer. I can also connect to Database Servers and Remote Desktop. I can see several computers when browsing network computers, but I am unable to connect to any of them. When trying to connect to a computer I am consistently met with the error code "0x80070035" (network path not found). I also get the 0x80070035 error when double clicking the target computer from the Network UI. I am not met with a login dialog when trying to access a computer, as I should, since I am not on the domain. (I did login to both Exchange, Remote Desktop and TFS though) Between Thursday where it worked and Sunday evening where it did not, I have installed quite a few security updates, plus various tools etc. that I need for programming. I have tried accessing by computer name and ip and neither of them work. I can ping by computer name. I have deleted all (1 entry) stored network credentials. I am able to access my computer from the target computer. Client and Server can see each other on the network = Network Discovery is enabled. I am using the network profile "Work". When accessing the network through VPN, I am unable to get anything to work using computernames, but all of the above applies when using IP adresses instead of computername. I run Windows 7 Home Premium on my computer. Using powershell attempting to access a share I get the following error (ComputerName and ShareName being correct values of course): PS C:\Users\MyUser> cd \\ComputerName\ShareName Set-Location : Cannot find path '\\ComputerName\ShareName' because it does not exist. At line:1 char:3 + cd <<<< \\ComputerName\ShareName + CategoryInfo : ObjectNotFound: (\\ComputerName\ShareName:String) [Set-Location], ItemNotFoundException + FullyQualifiedErrorId : PathNotFound,Microsoft.PowerShell.Commands.SetLocationCommand However, ping'ing the same machine (ping ComputerName) from powershell I get response immediately. (As mentioned in the list of observations/actions, I tried the above with the IP address again on VPN, to get the same result) Conclusion So to sum up, pretty much the only thing I can not do, is access the other computers through browsing (explorer.exe, powershell, map networkdrive, etc.), which means that I am pretty much down to, that it is unable to resolve the path somehow, when trying to connect to other computers trough browsing, though the path gets resolved perfectly using all kinds of other services. Any recommendations as to what I can try next to resolve the issue? :)

  Read the article

• Reinstall Postfix

  - by Kevin

  I tried to reinstall Postfix, but I get this bunch of errors: root@***:/etc/init.d# sudo apt-get install -f postfix Reading package lists... Done Building dependency tree Reading state information... Done Suggested packages: procmail postfix-mysql postfix-pgsql postfix-ldap postfix-pcre resolvconf postfix-cdb mail-reader The following NEW packages will be installed: postfix 0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded. Need to get 0B/1,389kB of archives. After this operation, 3,531kB of additional disk space will be used. Preconfiguring packages ... Selecting previously deselected package postfix. (Reading database ... 56122 files and directories currently installed.) Unpacking postfix (from .../postfix_2.7.1-1ubuntu0.1_amd64.deb) ... Processing triggers for ureadahead ... Processing triggers for ufw ... Processing triggers for man-db ... Setting up postfix (2.7.1-1ubuntu0.1) ... Configuration file `/etc/init.d/postfix' ==> File on system created by you or by a script. ==> File also in package provided by package maintainer. What would you like to do about it ? Your options are: Y or I : install the package maintainer's version N or O : keep your currently-installed version D : show the differences between the versions Z : start a shell to examine the situation The default action is to keep your current version. *** postfix (Y/I/N/O/D/Z) [default=N] ? Y Installing new version of config file /etc/init.d/postfix ... Adding group `postfix' (GID 109) ... Done. Adding system user `postfix' (UID 106) ... Adding new user `postfix' (UID 106) with group `postfix' ... Not creating home directory `/var/spool/postfix'. Creating /etc/postfix/dynamicmaps.cf Adding tcp map entry to /etc/postfix/dynamicmaps.cf Adding group `postdrop' (GID 115) ... Done. setting myhostname: ***.net setting alias maps setting alias database setting myorigin setting destinations: ***.net, localhost.***.net, , localhost setting relayhost: setting mynetworks: 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 setting mailbox_size_limit: 0 setting recipient_delimiter: + setting inet_interfaces: all Postfix is now set up with a default configuration. If you need to make changes, edit /etc/postfix/main.cf (and others) as needed. To view Postfix configuration values, see postconf(1). After modifying main.cf, be sure to run '/etc/init.d/postfix reload'. Running newaliases postalias: fatal: /etc/mailname: cannot open file: Permission denied dpkg: error processing postfix (--configure): subprocess installed post-installation script returned error exit status 1 Processing triggers for libc-bin ... ldconfig deferred processing now taking place Errors were encountered while processing: postfix E: Sub-process /usr/bin/dpkg returned an error code (1) I tried aptitude purge, remove, autoclean and all of dpkg options (configure, remove, purge) but nothing did the trick. /etc/mailname exists (0644 root:root) with as content *.net (fetched from hostname). What am I doing wrong?

  Read the article

• can't access nginx server from IP

  - by EquinoX

  So 2 days ago I can see that page where it saya "Welcome to nginx", however as of now when I tried to access it, it says 404 page not found... Why is this? Inside my sites-enabled folder I have a file named default and it has the following: # You may add here your # server { # ... # } # statements for each of your virtual hosts server { listen 80; server_name 127.0.0.1; access_log /var/log/nginx/localhost.access.log; location / { root /var/www/nginx-default; index index.html index.htm; } location /doc { root /usr/share; autoindex on; allow 127.0.0.1; deny all; } location /images { root /usr/share; autoindex on; } #error_page 404 /404.html; # redirect server error pages to the static page /50x.html # #error_page 500 502 503 504 /50x.html; #location = /50x.html { # root /var/www/nginx-default; #} # proxy the PHP scripts to Apache listening on 127.0.0.1:80 # #location ~ \.php$ { #proxy_pass http://127.0.0.1; #} # pass the PHP scripts to FastCGI server listening on 127.0.0.1:9000 # location ~ \.php$ { fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /var/www/nginx-default$fastcgi_script_name; include fastcgi_params; } # deny access to .htaccess files, if Apache's document root # concurs with nginx's one # location ~ /\.ht { deny all; } } # another virtual host using mix of IP-, name-, and port-based configuration # #server { #listen 8000; #listen somename:8080; #server_name somename alias another.alias; #location / { #root html; #index index.html index.htm; #} #} # HTTPS server # #server { #listen 443; #server_name localhost; #ssl on; #ssl_certificate cert.pem; #ssl_certificate_key cert.key; #ssl_session_timeout 5m; #ssl_protocols SSLv2 SSLv3 TLSv1; #ssl_ciphers ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP; #ssl_prefer_server_ciphers on; #location / { #root html; #index index.html index.htm; #} #} Here's my nginx.conf file: user www-data; worker_processes 4; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; # multi_accept on; } http { include /etc/nginx/mime.types; access_log /var/log/nginx/access.log; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; } # mail { # # See sample authentication script at: # # http://wiki.nginx.org/NginxImapAuthenticateWithApachePhpScript # # # auth_http localhost/auth.php; # # pop3_capabilities "TOP" "USER"; # # imap_capabilities "IMAP4rev1" "UIDPLUS"; # # server { # listen localhost:110; # protocol pop3; # proxy on; # } # # server { # listen localhost:143; # protocol imap; # proxy on; # } # } What am I doing wrong here? I have other virtual host setup in the sites-enabled as well... UPDATE: The server_name directives are: -admin.api.frapi -api.frapi -default -example.com -php.example.com

  Read the article

• What's going on with my server? High load, lots of idle CPU time, low disk utilization

  - by Jonathan

  I run a web site and send a legitimate opt-in, daily email newsletter to subscribers. Both the web hosting and email sending are done by the same machine. I have about 100,000 subscribers who have opted in to my daily email newsletter. My PHP script did a pretty good job sending mail to all of them until fairly recently, but as the list has grown I can't keep up. When I run top, I have very high load--usually at least 6 or 7, sometimes as high as 15--even though I only have two CPUs. However, when I run sar, my CPU is idle an average of about 30% of the time. So, it seems I'm not CPU bound. When I run iostat, it seems as though I'm not disk bound because my %util for each device is very low (no more than 5%). Given that I don't seem to be CPU bound or disk bound, why is top reporting such high load? Additionally, since I don't seem to be CPU bound or disk bound, why is my email sending script not able to keep up? Here's what I see when running top: top - 11:33:28 up 74 days, 18:49, 2 users, load average: 7.65, 8.79, 8.28 Tasks: 168 total, 5 running, 162 sleeping, 0 stopped, 1 zombie Cpu(s): 38.9%us, 58.6%sy, 0.8%ni, 0.0%id, 0.7%wa, 0.2%hi, 0.8%si, 0.0%st Mem: 3083012k total, 2144436k used, 938576k free, 281136k buffers Swap: 2048248k total, 39164k used, 2009084k free, 1470412k cached Here's what I see when running iostat -mx: avg-cpu: %user %nice %system %iowait %steal %idle 34.80 1.20 55.24 0.37 0.00 8.38 Device: rrqm/s wrqm/s r/s w/s rMB/s wMB/s avgrq-sz avgqu-sz await svctm %util sda 0.19 71.70 1.59 29.45 0.02 0.07 5.90 0.55 17.82 1.16 3.59 sda1 0.00 0.00 0.00 0.00 0.00 0.00 7.10 0.00 13.80 13.72 0.00 sda2 0.05 50.45 1.13 24.57 0.01 0.29 24.25 0.35 13.43 1.15 2.97 sda3 0.05 10.17 0.20 2.33 0.01 0.05 43.75 0.05 20.96 2.45 0.62 sda4 0.00 0.00 0.00 0.00 0.00 0.00 2.00 0.00 70.50 70.50 0.00 sda5 0.07 0.22 0.03 0.07 0.00 0.00 32.84 0.08 856.19 8.03 0.08 sda6 0.02 5.45 0.03 0.72 0.00 0.02 67.55 0.02 26.72 5.26 0.39 sda7 0.00 1.56 0.00 0.42 0.00 0.01 38.04 0.00 8.88 5.84 0.24 sda8 0.01 3.84 0.20 1.35 0.00 0.02 28.55 0.05 31.90 4.08 0.63 Here's what I see when running sar: 09:40:02 AM CPU %user %nice %system %iowait %steal %idle 09:50:01 AM all 30.59 1.01 49.80 0.23 0.00 18.37 10:00:08 AM all 31.73 0.92 51.66 0.13 0.00 15.55 10:10:06 AM all 30.43 0.99 48.94 0.26 0.00 19.38 10:20:01 AM all 29.58 1.00 47.76 0.25 0.00 21.42 10:30:01 AM all 29.37 1.02 47.30 0.18 0.00 22.13 10:40:06 AM all 32.50 1.01 52.94 0.16 0.00 13.39 10:50:01 AM all 30.49 1.00 49.59 0.15 0.00 18.77 11:00:01 AM all 29.43 0.99 47.71 0.17 0.00 21.71 11:10:07 AM all 30.26 0.93 49.48 0.83 0.00 18.50 11:20:02 AM all 29.83 0.81 48.51 1.32 0.00 19.52 11:30:06 AM all 31.18 0.88 51.33 1.15 0.00 15.47 Average: all 26.21 1.15 42.62 0.48 0.00 29.54 Here are the top handful of processes listed at the particular time I happened to run top -c: PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 8180 mysql 16 0 57448 19m 2948 S 26.6 0.7 4702:26 /usr/sbin/mysqld --basedir=/ --datadir=/var/lib/mysql --user=mysql --pid-file=/var/lib/mysql/bristno.pid --skip-external-locking 26956 brristno 17 0 0 0 0 Z 8.0 0.0 0:00.24 [php] <defunct> 26958 brristno 17 0 94408 43m 37m R 5.0 1.4 0:00.15 /usr/bin/php /home/brristno/public_html/dbv.php 22852 nobody 16 0 9628 2900 1524 S 0.7 0.1 0:00.17 /usr/local/apache/bin/httpd -k start -DSSL 8591 brristno 34 19 96896 13m 6652 S 0.3 0.4 0:29.82 /usr/local/bin/php /home/brristno/bin/mailer.php 1qwqyb6 i0gbor 24469 nobody 16 0 9628 2880 1508 S 0.3 0.1 0:00.08 /usr/local/apache/bin/httpd -k start -DSSL 25495 nobody 15 0 9628 2876 1500 S 0.3 0.1 0:00.06 /usr/local/apache/bin/httpd -k start -DSSL 26149 nobody 15 0 9628 2864 1504 S 0.3 0.1 0:00.04 /usr/local/apache/bin/httpd -k start -DSSL

  Read the article

• How to validate referral support implemented for Active Dircetory server?

  - by user146560

  Please suggest me some utility or application, using which i want to test referral settings done. I want to test cross forest referenced reference. Among two DNS say 1 firstDNS.com user([email protected]) 2 SecondDNS.com user([email protected]) Below java code written to test active directory server setting. public void authenticateUser(String user, String password, String domain) throws AuthenticationException, NamingException { List<String> ldapServers = findLDAPServersInWindowsDomain("first.com"); if (ldapServers.isEmpty()) throw new NamingException("Can't locate an LDAP server (try nslookup type=SRV _ldap._tcp." + "first.com"+ ")"); Hashtable<String, String> props = new Hashtable<String, String>(); String principalName = "testUserFirst"+ "@" + "First.com"; props.put(Context.SECURITY_PRINCIPAL, principalName); props.put(Context.SECURITY_CREDENTIALS, password); props.put(Context.REFERRAL,"follow"); //props.put(Context.SECURITY_AUTHENTICATION, "anonymous"); Integer count = 0; for (String ldapServer : ldapServers) { try { count++; DirContext ctx = LdapCtxFactory.getLdapCtxInstance("ldap://" + ldapServer, props); SearchControls searchCtls = new SearchControls(); //Specify the attributes to return String returnedAtts[]={"sn","givenName","mail"}; searchCtls.setReturningAttributes(returnedAtts); //Specify the search scope searchCtls.setSearchScope(SearchControls.SUBTREE_SCOPE); //specify the LDAP search filter String searchFilter = "(&(objectClass=user)(sAMAccountName=" testUserSecond)(userPassword=usertest@3))"; //Specify the Base for the search String searchBase = "DC=second,DC=com"; //initialize counter to total the results int totalResults = 0; // Search for objects using the filter NamingEnumeration<SearchResult> answer = ctx.search(searchBase, searchFilter, searchCtls); return; } catch (CommunicationException e) { // this is what'll happen if one of the domain controllers is unreachable if (count.equals(ldapServers.size())) { // we've got no more servers to try, so throw the CommunicationException to indicate that we failed to reach an LDAP server throw e; } } } } private List<String> findLDAPServersInWindowsDomain(String domain) throws NamingException { List<String> servers = new ArrayList<String>(); Hashtable<String, String> env = new Hashtable<String, String>(); env.put(Context.INITIAL_CONTEXT_FACTORY, "com.sun.jndi.dns.DnsContextFactory"); env.put("java.naming.provider.url", "dns://"); DirContext ctx = new InitialDirContext(env); Attributes attributes = ctx.getAttributes("_ldap._tcp." + domain, new String[] { "SRV" }); // that's how Windows domain controllers are registered in DNS Attribute a = attributes.get("SRV"); for (int i = 0; i < a.size(); i++) { String srvRecord = a.get(i).toString(); // each SRV record is in the format "0 100 389 dc1.company.com." // priority weight port server (space separated) servers.add(srvRecord.split(" ")[3]); } ctx.close(); return servers; }

  Read the article

< Previous Page | 404 405 406 407 408 409 410 411 412 413 414 415  | Next Page >