Search Results

Search found 3140 results on 126 pages for 'debian'.

Page 41/126 | < Previous Page | 37 38 39 40 41 42 43 44 45 46 47 48  | Next Page >

• Why doesn't pppd over ssh work here? Why can't I kill pppd?

  - by Peter V. Mørch

  I'm trying to setup a simple ppp tunnel over ssh. It works on several machines just fine. But on one machine, pppd gets "stuck": > pgrep pppd | xargs ps up USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 4178 0.0 0.1 3020 1088 pts/1 Ds+ 05:28 0:00 /usr/sbin/pppd Any attempt to kill it (even sudo kill -9 4178) has no effect that I can see. strace -p 4178 also hangs similarly. After it has been started for a while, I start getting messages in dmesg like shown below. It is started like so from another machine: ssh -t root@server /usr/sbin/pppd passive noauth When I do this to one of the machines that work, the remote end's pppd spits out garbage/binary data to the console (as expected). When I do it to the one that fails, I get no output from pppd, but the ssh session eventually times out. If I instead ssh to the machine, and then run /usr/sbin/pppd passive noauth in a separate step I also get the expected binary output. I now have a couple of questions: What could be up with the one machine where pppd fails? I don't even know where to start looking... What could be the difference between ssh -t root@server /usr/sbin/pppd passive noauth in a single step and ssh root@server and /usr/sbin/pppd passive noauth in two steps? How can it be that I can't kill the process even with sudo kill -9? The only way I know is to reboot. (I've tried searching for something similar but didn't get anywhere so I'm sorry I don't have any more leads) Any ideas? The problem machine runs in debian on VMware "hardware" (as do the ones that work) and it exhibits the problem when cloned and on both debian lenny (original) and squeeze (after upgrade) dmesg entries: [ 1198.727248] INFO: task pppd:4178 blocked for more than 120 seconds. [ 1198.727507] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1198.727904] pppd D ece2dc9c 0 4178 4174 0x00000004 [ 1198.727908] 00000098 00000082 f2503520 ece2dc9c 0000b1e7 00000000 c148d1c0 c148d1c0 [ 1198.727913] f2a06100 f6e071c0 00000000 ece2dc18 f5cd07e0 00000000 ece2d400 ece2dc9d [ 1198.727918] 00c52300 ece2dcbc f67bfef8 ec98e480 f291cec0 00000000 c10cf5b0 c10dfd21 [ 1198.727923] Call Trace: [ 1198.727926] [<c10cf5b0>] ? nameidata_to_filp+0x37/0x41 [ 1198.727929] [<c10dfd21>] ? dput+0x21/0xb7 [ 1198.727932] [<c11cfecc>] ? tty_ldisc_ref_wait+0x5f/0x76 [ 1198.727935] [<c104de7a>] ? wake_up_bit+0x5c/0x5c [ 1198.727938] [<c11cb91b>] ? tty_ioctl+0x85f/0x8ba [ 1198.727941] [<c10fec18>] ? do_lock_file_wait+0x3d/0xd9 [ 1198.727944] [<c1162c97>] ? _copy_from_user+0x2b/0x102 [ 1198.727946] [<c11cb0bc>] ? tty_check_change+0xb9/0xb9 [ 1198.727949] [<c10dbeb7>] ? do_vfs_ioctl+0x485/0x4c7 [ 1198.727952] [<c10db59a>] ? do_fcntl+0x24f/0x3a2 [ 1198.727954] [<c10dbf3a>] ? sys_ioctl+0x41/0x58 [ 1198.727957] [<c12c6a1f>] ? sysenter_do_call+0x12/0x28 [ 1318.457225] INFO: task sshd:4174 blocked for more than 120 seconds. [ 1318.457500] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [ 1318.457896] sshd D f25024cc 0 4174 2393 0x00000000 [ 1318.457901] 00000098 00000086 f2a06940 f25024cc 0000b246 00000000 c148d1c0 c148d1c0 [ 1318.457906] f2503520 f6e071c0 00000000 3f056585 0000000f ece2d4bc 3f056585 f2503520 [ 1318.457911] ec98bb38 ec98bbdc 00000000 00000000 00000000 c12c09b5 f2503520 c10327cb [ 1318.457916] Call Trace: [ 1318.457926] [<c12c09b5>] ? schedule_hrtimeout_range_clock+0x3c/0xd9 [ 1318.457931] [<c10327cb>] ? try_to_wake_up+0x13f/0x13f [ 1318.457935] [<c11cfecc>] ? tty_ldisc_ref_wait+0x5f/0x76 [ 1318.457940] [<c104de7a>] ? wake_up_bit+0x5c/0x5c [ 1318.457943] [<c11c9ad3>] ? tty_poll+0x32/0x5e [ 1318.457947] [<c10dd4d5>] ? do_select+0x2a1/0x42e [ 1318.457950] [<c10dcb83>] ? poll_freewait+0x69/0x69 [ 1318.457953] [<c10dcc25>] ? __pollwait+0xa2/0xa2 [ 1318.457955] [<c10dcc25>] ? __pollwait+0xa2/0xa2 [ 1318.457958] [<c10dcc25>] ? __pollwait+0xa2/0xa2 [ 1318.457960] [<c10dcc25>] ? __pollwait+0xa2/0xa2 [ 1318.457963] [<c10dcc25>] ? __pollwait+0xa2/0xa2 [ 1318.457965] [<c10dcc25>] ? __pollwait+0xa2/0xa2 [ 1318.457968] [<c10dcc25>] ? __pollwait+0xa2/0xa2 [ 1318.457971] [<c10429c2>] ? lock_timer_base+0x19/0x35 [ 1318.457974] [<c1042eb5>] ? __mod_timer+0x10c/0x116 [ 1318.457977] [<c1042f89>] ? mod_timer+0x69/0x6e [ 1318.457981] [<c121325d>] ? sk_reset_timer+0xc/0x16 [ 1318.457984] [<c1252f57>] ? tcp_event_new_data_sent+0x66/0x6b [ 1318.457987] [<c1255b85>] ? tcp_write_xmit+0x7a7/0x86a [ 1318.457990] [<c121760d>] ? __alloc_skb+0x50/0xfd [ 1318.457994] [<c12c12bc>] ? _raw_spin_lock_bh+0x8/0x1e [ 1318.457996] [<c1212e98>] ? release_sock+0x10/0xc4 [ 1318.457999] [<c124b543>] ? tcp_sendmsg+0x6dd/0x7b7 [ 1318.458003] [<c1162c97>] ? _copy_from_user+0x2b/0x102 [ 1318.458006] [<c10dd7a0>] ? core_sys_select+0x13e/0x1c3 [ 1318.458009] [<c12102a3>] ? sock_aio_write+0xc0/0xd4 [ 1318.458012] [<c10d0655>] ? do_sync_write+0xa0/0xe4 [ 1318.458016] [<c10b141c>] ? handle_mm_fault+0x222/0x238 [ 1318.458019] [<c10f6096>] ? fsnotify+0x1de/0x1f9 [ 1318.458022] [<c10dd9e8>] ? sys_select+0x6e/0x8f [ 1318.458024] [<c10d105e>] ? sys_write+0x3c/0x63 [ 1318.458028] [<c12c6a1f>] ? sysenter_do_call+0x12/0x28

  Read the article

• apt-get update mdadm scary warnings

  - by user568829

  Just ran an apt-get update on one of my dedicated servers to be left with a relatively scary warning: Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-2.6.26-2-686-bigmem W: mdadm: the array /dev/md/1 with UUID c622dd79:496607cf:c230666b:5103eba0 W: mdadm: is currently active, but it is not listed in mdadm.conf. if W: mdadm: it is needed for boot, then YOUR SYSTEM IS NOW UNBOOTABLE! W: mdadm: please inspect the output of /usr/share/mdadm/mkconf, compare W: mdadm: it to /etc/mdadm/mdadm.conf, and make the necessary changes. W: mdadm: the array /dev/md/2 with UUID 24120323:8c54087c:c230666b:5103eba0 W: mdadm: is currently active, but it is not listed in mdadm.conf. if W: mdadm: it is needed for boot, then YOUR SYSTEM IS NOW UNBOOTABLE! W: mdadm: please inspect the output of /usr/share/mdadm/mkconf, compare W: mdadm: it to /etc/mdadm/mdadm.conf, and make the necessary changes. W: mdadm: the array /dev/md/6 with UUID eef74de5:9267b2a1:c230666b:5103eba0 W: mdadm: is currently active, but it is not listed in mdadm.conf. if W: mdadm: it is needed for boot, then YOUR SYSTEM IS NOW UNBOOTABLE! W: mdadm: please inspect the output of /usr/share/mdadm/mkconf, compare W: mdadm: it to /etc/mdadm/mdadm.conf, and make the necessary changes. W: mdadm: the array /dev/md/5 with UUID 5d45b20c:04d8138f:c230666b:5103eba0 W: mdadm: is currently active, but it is not listed in mdadm.conf. if W: mdadm: it is needed for boot, then YOUR SYSTEM IS NOW UNBOOTABLE! W: mdadm: please inspect the output of /usr/share/mdadm/mkconf, compare W: mdadm: it to /etc/mdadm/mdadm.conf, and make the necessary changes. As instructed I inspected the output of /usr/share/mdadm/mkconf and compared with /etc/mdadm/mdadm.conf and they are quite different. Here is the /etc/mdadm/mdadm.conf contents: # mdadm.conf # # Please refer to mdadm.conf(5) for information about this file. # # by default, scan all partitions (/proc/partitions) for MD superblocks. # alternatively, specify devices to scan, using wildcards if desired. DEVICE partitions # auto-create devices with Debian standard permissions CREATE owner=root group=disk mode=0660 auto=yes # automatically tag new arrays as belonging to the local system HOMEHOST <system> # instruct the monitoring daemon where to send mail alerts MAILADDR root # definitions of existing MD arrays ARRAY /dev/md0 level=raid1 num-devices=2 UUID=b93b0b87:5f7c2c46:0043fca9:4026c400 ARRAY /dev/md1 level=raid1 num-devices=2 UUID=c0fa8842:e214fb1a:fad8a3a2:28f2aabc ARRAY /dev/md2 level=raid1 num-devices=2 UUID=cdc2a9a9:63bbda21:f55e806c:a5371897 ARRAY /dev/md3 level=raid1 num-devices=2 UUID=eca75495:9c9ce18c:d2bac587:f1e79d80 # This file was auto-generated on Wed, 04 Nov 2009 11:32:16 +0100 # by mkconf $Id$ And here is the out put from /usr/share/mdadm/mkconf # mdadm.conf # # Please refer to mdadm.conf(5) for information about this file. # # by default, scan all partitions (/proc/partitions) for MD superblocks. # alternatively, specify devices to scan, using wildcards if desired. DEVICE partitions # auto-create devices with Debian standard permissions CREATE owner=root group=disk mode=0660 auto=yes # automatically tag new arrays as belonging to the local system HOMEHOST <system> # instruct the monitoring daemon where to send mail alerts MAILADDR root # definitions of existing MD arrays ARRAY /dev/md1 UUID=c622dd79:496607cf:c230666b:5103eba0 ARRAY /dev/md2 UUID=24120323:8c54087c:c230666b:5103eba0 ARRAY /dev/md5 UUID=5d45b20c:04d8138f:c230666b:5103eba0 ARRAY /dev/md6 UUID=eef74de5:9267b2a1:c230666b:5103eba0 # This configuration was auto-generated on Sat, 25 Feb 2012 13:10:00 +1030 # by mkconf 3.1.4-1+8efb9d1+squeeze1 As I understand it I need to replace the four lines that start with 'ARRAY' in the /etc/mdadm/mdadm.conf file with the different four 'ARRAY' lines from the /usr/share/mdadm/mkconf output. When I did this and then ran update-initramfs -u there were no more warnings. Is what I have done above correct? I am now terrified of rebooting the server for fear it will not reboot and being a remote dedicated server this would certainly mean downtime and possibly would be expensive to get running again. FOLLOW UP (response to question): the output from mount: /dev/md1 on / type ext3 (rw,usrquota,grpquota) tmpfs on /lib/init/rw type tmpfs (rw,nosuid,mode=0755) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) udev on /dev type tmpfs (rw,mode=0755) tmpfs on /dev/shm type tmpfs (rw,nosuid,nodev) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=620) /dev/md2 on /boot type ext2 (rw) /dev/md5 on /tmp type ext3 (rw) /dev/md6 on /home type ext3 (rw,usrquota,grpquota) mdadm --detail /dev/md0 mdadm: md device /dev/md0 does not appear to be active. mdadm --detail /dev/md1 /dev/md1: Version : 0.90 Creation Time : Sun Aug 14 09:43:08 2011 Raid Level : raid1 Array Size : 31463232 (30.01 GiB 32.22 GB) Used Dev Size : 31463232 (30.01 GiB 32.22 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Sat Feb 25 14:03:47 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : c622dd79:496607cf:c230666b:5103eba0 Events : 0.24 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 8 17 1 active sync /dev/sdb1 mdadm --detail /dev/md2 /dev/md2: Version : 0.90 Creation Time : Sun Aug 14 09:43:09 2011 Raid Level : raid1 Array Size : 104320 (101.89 MiB 106.82 MB) Used Dev Size : 104320 (101.89 MiB 106.82 MB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Sat Feb 25 13:20:20 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 24120323:8c54087c:c230666b:5103eba0 Events : 0.30 Number Major Minor RaidDevice State 0 8 2 0 active sync /dev/sda2 1 8 18 1 active sync /dev/sdb2 mdadm --detail /dev/md3 mdadm: md device /dev/md3 does not appear to be active. mdadm --detail /dev/md5 /dev/md5: Version : 0.90 Creation Time : Sun Aug 14 09:43:09 2011 Raid Level : raid1 Array Size : 2104448 (2.01 GiB 2.15 GB) Used Dev Size : 2104448 (2.01 GiB 2.15 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 5 Persistence : Superblock is persistent Update Time : Sat Feb 25 14:09:03 2012 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 5d45b20c:04d8138f:c230666b:5103eba0 Events : 0.30 Number Major Minor RaidDevice State 0 8 5 0 active sync /dev/sda5 1 8 21 1 active sync /dev/sdb5 mdadm --detail /dev/md6 /dev/md6: Version : 0.90 Creation Time : Sun Aug 14 09:43:09 2011 Raid Level : raid1 Array Size : 453659456 (432.64 GiB 464.55 GB) Used Dev Size : 453659456 (432.64 GiB 464.55 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 6 Persistence : Superblock is persistent Update Time : Sat Feb 25 14:10:00 2012 State : active Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : eef74de5:9267b2a1:c230666b:5103eba0 Events : 0.31 Number Major Minor RaidDevice State 0 8 6 0 active sync /dev/sda6 1 8 22 1 active sync /dev/sdb6 FOLLOW UP 2 (response to question): Output from /etc/fstab /dev/md1 / ext3 defaults,usrquota,grpquota 1 1 devpts /dev/pts devpts mode=0620,gid=5 0 0 proc /proc proc defaults 0 0 #usbdevfs /proc/bus/usb usbdevfs noauto 0 0 /dev/cdrom /media/cdrom auto ro,noauto,user,exec 0 0 /dev/dvd /media/dvd auto ro,noauto,user,exec 0 0 # # # /dev/md2 /boot ext2 defaults 1 2 /dev/sda3 swap swap pri=42 0 0 /dev/sdb3 swap swap pri=42 0 0 /dev/md5 /tmp ext3 defaults 0 0 /dev/md6 /home ext3 defaults,usrquota,grpquota 1 2

  Read the article

• Server randomly freezes

  - by PsySkeletor

  Im facing a very strange issue, my debian squeeze freezes up always at night (Berlin, time). Here is what i get from a time and after doing this a few times, it becomes frozen and must be hard-reset. From /var/log/messages Dec 11 01:36:11 srv156 kernel: [125983.204251] CPU 1: Dec 11 01:36:11 srv156 kernel: [125983.204251] Modules linked in: xt_multiport nf_conntrack_ipv4 nf_defrag_ipv4 xt_recent xt_state nf_conntrack xt_tcpudp iptable_filter ip_tables x_tables hwmon_vid snd_hda_codec_atihdmi snd_hda_intel snd_hda_codec snd_hwdep snd_pcm radeon snd_timer ttm drm_kms_helper snd k10temp i2c_piix4 soundcore snd_page_alloc edac_core parport_pc drm i2c_algo_bit i2c_core shpchp pci_hotplug pcspkr edac_mce_amd parport wmi evdev processor button ext3 jbd mbcache raid1 md_mod sd_mod crc_t10dif ata_generic ahci ohci_hcd pata_atiixp e100 mii libata xhci floppy ehci_hcd thermal thermal_sys usbcore scsi_mod nls_base [last unloaded: i2c_dev] Dec 11 01:36:11 srv156 kernel: [125983.204251] Pid: 758, comm: flush-9:0 Tainted: G B 2.6.32-5-amd64 #1 GA-78LMT-USB3 Dec 11 01:36:11 srv156 kernel: [125983.204251] RIP: 0010:[<ffffffff810b3506>] [<ffffffff810b3506>] find_get_pages_tag+0x66/0xdd Dec 11 01:36:11 srv156 kernel: [125983.204251] RSP: 0018:ffff8804235e7b30 EFLAGS: 00000286 Dec 11 01:36:11 srv156 kernel: [125983.204251] RAX: ffffffffffffffff RBX: ffff8804235e7c00 RCX: 0000000000000000 Dec 11 01:36:11 srv156 kernel: [125983.204251] RDX: 0000000000040000 RSI: ffffea000496b2a8 RDI: ffffea000496b2a0 Dec 11 01:36:11 srv156 kernel: [125983.204251] RBP: ffffffff8101166e R08: ffff8804235e7af0 R09: 0000000000000000 Dec 11 01:36:11 srv156 kernel: [125983.204251] R10: 0000000000000000 R11: 0000000000040000 R12: ffff8804235e7c08 Dec 11 01:36:11 srv156 kernel: [125983.204251] R13: 0000000d22678a20 R14: ffff8804235e7af0 R15: 00000000091b9060 Dec 11 01:36:11 srv156 kernel: [125983.204251] FS: 0000000000000000(0000) GS:ffff880010440000(0000) knlGS:000000007ebf7b70 Dec 11 01:36:11 srv156 kernel: [125983.204522] CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b Dec 11 01:36:11 srv156 kernel: [125983.204522] CR2: 00000000dec86000 CR3: 0000000001001000 CR4: 00000000000006e0 Dec 11 01:36:11 srv156 kernel: [125983.204522] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 Dec 11 01:36:11 srv156 kernel: [125983.204522] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Dec 11 01:36:11 srv156 kernel: [125983.204522] Call Trace: Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff810bb792>] ? pagevec_lookup_tag+0x1a/0x21 Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff810ba330>] ? write_cache_pages+0x162/0x327 Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff810b9d48>] ? __writepage+0x0/0x25 Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff8110758a>] ? writeback_single_inode+0xe7/0x2da Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff81108290>] ? writeback_inodes_wb+0x424/0x4ff Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff81108497>] ? wb_writeback+0x12c/0x1ab Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff8110870d>] ? wb_do_writeback+0x14f/0x165 Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff81108754>] ? bdi_writeback_task+0x31/0xaa Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff810c8664>] ? bdi_start_fn+0x0/0xd0 Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff810c86d4>] ? bdi_start_fn+0x70/0xd0 Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff810c8664>] ? bdi_start_fn+0x0/0xd0 Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff81064ac1>] ? kthread+0x79/0x81 Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff81011baa>] ? child_rip+0xa/0x20 Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff81064a48>] ? kthread+0x0/0x81 Dec 11 01:36:11 srv156 kernel: [125983.204522] [<ffffffff81011ba0>] ? child_rip+0x0/0x20 From /var/log/syslog Dec 10 21:20:29 srv156 kernel: [110625.162930] BUG: Bad page map in process java pte:14fa4f067 pmd:424b54067 Dec 10 21:20:29 srv156 kernel: [110625.162937] page:ffffea000496c148 flags:0200000000000878 count:2 mapcount:-1 mapping:ffff88014f8d7de8 index:2f4 Dec 10 21:20:29 srv156 kernel: [110625.162946] addr:0000000009096000 vm_flags:00100077 anon_vma:ffff880422410d40 mapping:(null) index:9096 Dec 10 21:20:29 srv156 kernel: [110625.162955] Pid: 21356, comm: java Tainted: G B 2.6.32-5-amd64 #1 Dec 10 21:20:29 srv156 kernel: [110625.162961] Call Trace: Dec 10 21:20:29 srv156 kernel: [110625.162966] [<ffffffff810ca4bf>] ? print_bad_pte+0x232/0x24a Dec 10 21:20:29 srv156 kernel: [110625.162973] [<ffffffff810cb56f>] ? unmap_vmas+0x62d/0x931 Dec 10 21:20:29 srv156 kernel: [110625.162980] [<ffffffff810cfc74>] ? exit_mmap+0xc4/0x148 Dec 10 21:20:29 srv156 kernel: [110625.162986] [<ffffffff8104bbc1>] ? mmput+0x3c/0xdf Dec 10 21:20:29 srv156 kernel: [110625.162992] [<ffffffff8104f81e>] ? exit_mm+0x102/0x10d Dec 10 21:20:29 srv156 kernel: [110625.162998] [<ffffffff81051243>] ? do_exit+0x1f8/0x6c9 Dec 10 21:20:29 srv156 kernel: [110625.163004] [<ffffffff81071abb>] ? futex_wake+0xd6/0xe7 Dec 10 21:20:29 srv156 kernel: [110625.163010] [<ffffffff8105178a>] ? do_group_exit+0x76/0x9d Dec 10 21:20:29 srv156 kernel: [110625.163016] [<ffffffff8105df9f>] ? get_signal_to_deliver+0x310/0x339 Dec 10 21:20:29 srv156 kernel: [110625.163023] [<ffffffff81010037>] ? do_notify_resume+0x87/0x73f Dec 10 21:20:29 srv156 kernel: [110625.163029] [<ffffffff810cc664>] ? handle_mm_fault+0x7aa/0x80f Dec 10 21:20:29 srv156 kernel: [110625.163036] [<ffffffff81073f14>] ? compat_sys_futex+0x10d/0x12b Dec 10 21:20:29 srv156 kernel: [110625.163043] [<ffffffff812fb546>] ? do_page_fault+0x2e0/0x2fc Dec 10 21:20:29 srv156 kernel: [110625.163049] [<ffffffff81010e0e>] ? int_signal+0x12/0x17 Dec 10 21:20:29 srv156 kernel: [110625.163114] BUG: Bad page state in process java pfn:14fa0c Dec 10 21:20:29 srv156 kernel: [110625.163120] page:ffffea000496b2a0 flags:020000000002001c count:0 mapcount:-1 mapping:ffff88039dc0db30 index:11e3 Dec 10 21:20:29 srv156 kernel: [110625.164563] Pid: 21356, comm: java Tainted: G B 2.6.32-5-amd64 #1 Dec 10 21:20:29 srv156 kernel: [110625.164570] Call Trace: Dec 10 21:20:29 srv156 kernel: [110625.164578] [<ffffffff810b71a9>] ? bad_page+0x116/0x129 Dec 10 21:20:29 srv156 kernel: [110625.164586] [<ffffffff810b7692>] ? free_pages_check+0x38/0x57 Dec 10 21:20:29 srv156 kernel: [110625.164595] [<ffffffff810b89cf>] ? free_hot_cold_page+0x46/0x190 Dec 10 21:20:29 srv156 kernel: [110625.164603] [<ffffffff810b8b82>] ? __pagevec_free+0x69/0x7f Dec 10 21:20:29 srv156 kernel: [110625.164611] [<ffffffff810bba3f>] ? release_pages+0x137/0x18d Dec 10 21:20:29 srv156 kernel: [110625.164620] [<ffffffff810d8559>] ? free_pages_and_swap_cache+0x57/0x73 Dec 10 21:20:29 srv156 kernel: [110625.164629] [<ffffffff810cb5ed>] ? unmap_vmas+0x6ab/0x931 Dec 10 21:20:29 srv156 kernel: [110625.164637] [<ffffffff810cfc74>] ? exit_mmap+0xc4/0x148 Dec 10 21:20:29 srv156 kernel: [110625.164644] [<ffffffff8104bbc1>] ? mmput+0x3c/0xdf Dec 10 21:20:29 srv156 kernel: [110625.164652] [<ffffffff8104f81e>] ? exit_mm+0x102/0x10d Dec 10 21:20:29 srv156 kernel: [110625.164660] [<ffffffff81051243>] ? do_exit+0x1f8/0x6c9 Dec 10 21:20:29 srv156 kernel: [110625.164667] [<ffffffff81071abb>] ? futex_wake+0xd6/0xe7 Dec 10 21:20:29 srv156 kernel: [110625.164675] [<ffffffff8105178a>] ? do_group_exit+0x76/0x9d Dec 10 21:20:29 srv156 kernel: [110625.164683] [<ffffffff8105df9f>] ? get_signal_to_deliver+0x310/0x339 Dec 10 21:20:29 srv156 kernel: [110625.164692] [<ffffffff81010037>] ? do_notify_resume+0x87/0x73f Dec 10 21:20:29 srv156 kernel: [110625.164700] [<ffffffff810cc664>] ? handle_mm_fault+0x7aa/0x80f The last piece of log, has been recently posted, because I've just found it. It seems Java process do something and began to slowly eat all the resources of the server. I don't know exactly if this could be the root cause. Im using Debian Squeeze. uname -a Linux srv156 2.6.32-5-amd64 #1 SMP Sun Sep 23 11:00:33 UTC 2012 x86_64 GNU/Linux I really will appreciate your help, i dont know what more to do.

  Read the article

• "Can't Connect to Server" from 2nd virtual host on VPS

  - by chaoskreator

  I'm using Debian 7 Wheezy and Apache 2.2.22, and I'm setting up Virtual Hosts for a number of websites on my VPS. I've successfully configured the VirtualHost directives for one of the sites, but the second one continually gives "Problem Loading Page" in Firefox. I've run configtest and it has verified all my syntax is correct, and I've checked all the permissions. Everything on the 2nd domain is pretty much copy/pasted from the first, so I'm not sure what the issue is, as there are no entries into /var/log/apache2/error.log other than where I have reloaded the configurations: /# cat /var/log/apache2/error.log [Thu May 29 01:19:00 2014] [notice] Graceful restart requested, doing restart [Thu May 29 01:19:00 2014] [info] Init: Seeding PRNG with 656 bytes of entropy [Thu May 29 01:19:00 2014] [info] Init: Generating temporary RSA private keys (512/1024 bits) [Thu May 29 01:19:00 2014] [info] Init: Generating temporary DH parameters (512/1024 bits) [Thu May 29 01:19:00 2014] [debug] ssl_scache_shmcb.c(253): shmcb_init allocated 512000 bytes of shared memory [Thu May 29 01:19:00 2014] [debug] ssl_scache_shmcb.c(272): for 511920 bytes (512000 including header), recommending 32 subcaches, 133 indexes each [Thu May 29 01:19:00 2014] [debug] ssl_scache_shmcb.c(306): shmcb_init_memory choices follow [Thu May 29 01:19:00 2014] [debug] ssl_scache_shmcb.c(308): subcache_num = 32 [Thu May 29 01:19:00 2014] [debug] ssl_scache_shmcb.c(310): subcache_size = 15992 [Thu May 29 01:19:00 2014] [debug] ssl_scache_shmcb.c(312): subcache_data_offset = 3208 [Thu May 29 01:19:00 2014] [debug] ssl_scache_shmcb.c(314): subcache_data_size = 12784 [Thu May 29 01:19:00 2014] [debug] ssl_scache_shmcb.c(316): index_num = 133 [Thu May 29 01:19:00 2014] [info] Shared memory session cache initialised [Thu May 29 01:19:00 2014] [info] Init: Initializing (virtual) servers for SSL [Thu May 29 01:19:00 2014] [info] mod_ssl/2.2.22 compiled against Server: Apache/2.2.22, Library: OpenSSL/1.0.1e [Thu May 29 01:19:00 2014] [notice] Apache/2.2.22 (Debian) PHP/5.4.4-14+deb7u9 mod_ssl/2.2.22 OpenSSL/1.0.1e mod_perl/2.0.7 Perl/v5.14.2 configured -- resuming normal operations [Thu May 29 01:19:00 2014] [info] Server built: Mar 4 2013 22:05:16 [Thu May 29 01:19:00 2014] [debug] prefork.c(1023): AcceptMutex: sysvsem (default: sysvsem) I've ensured to enable each vhost with a2ensite {sitename.conf} with no errors there, either. Below are the contents of the configuration files... /etc/apache2/apache2.conf # Global configuration # LockFile ${APACHE_LOCK_DIR}/accept.lock PidFile ${APACHE_PID_FILE} Timeout 300 KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 5 ## ## Server-Pool Size Regulation (MPM specific) ## # prefork MPM # StartServers: number of server processes to start # MinSpareServers: minimum number of server processes which are kept spare # MaxSpareServers: maximum number of server processes which are kept spare # MaxClients: maximum number of server processes allowed to start # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 5 MaxSpareServers 10 MaxClients 150 MaxRequestsPerChild 0 </IfModule> # worker MPM # StartServers: initial number of server processes to start # MinSpareThreads: minimum number of worker threads which are kept spare # MaxSpareThreads: maximum number of worker threads which are kept spare # ThreadLimit: ThreadsPerChild can be changed to this maximum value during a # graceful restart. ThreadLimit can only be changed by stopping # and starting Apache. # ThreadsPerChild: constant number of worker threads in each server process # MaxClients: maximum number of simultaneous client connections # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_worker_module> StartServers 2 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxClients 150 MaxRequestsPerChild 0 </IfModule> # event MPM # StartServers: initial number of server processes to start # MinSpareThreads: minimum number of worker threads which are kept spare # MaxSpareThreads: maximum number of worker threads which are kept spare # ThreadsPerChild: constant number of worker threads in each server process # MaxClients: maximum number of simultaneous client connections # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_event_module> StartServers 2 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxClients 150 MaxRequestsPerChild 0 </IfModule> # These need to be set in /etc/apache2/envvars User ${APACHE_RUN_USER} Group ${APACHE_RUN_GROUP} # # AccessFileName: The name of the file to look for in each directory # for additional configuration directives. See also the AllowOverride # directive. # AccessFileName .htaccess # # The following lines prevent .htaccess and .htpasswd files from being # viewed by Web clients. # <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy all </Files> DefaultType None HostnameLookups Off ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel debug # Include module configuration: Include mods-enabled/*.load Include mods-enabled/*.conf # Include list of ports to listen on and which to use for name based vhosts Include ports.conf # # The following directives define some format nicknames for use with # a CustomLog directive (see below). # If you are behind a reverse proxy, you might want to change %h into %{X-Forwarded-For}i # # LogFormat "%v:%p %h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" vhost_combined LogFormat "%h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %O" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent <Directory "/var/www"> Order allow,deny Allow from all Require all granted </Directory> # Include generic snippets of statements Include conf.d/ # Include the virtual host configurations: Include sites-enabled/*.conf NameVirtualHost *:80 /etc/apache2/sites-available/site1.net.conf <VirtualHost *:80> ServerName site1.net ServerAlias site1.net *.site1.net DocumentRoot "/var/www/site1" ErrorLog "/var/www/site1/logs/error.log" CustomLog "/var/www/site1/logs/access.log" vhost_combined <Directory "/var/www/site1"> Options None AllowOverride All Order allow,deny Allow from all Satisfy Any </Directory> </VirtualHost> /etc/apache2/sites-available/site2.com.conf <VirtualHost *:80> ServerName site2.com ServerAlias site2.com *.site2.com DocumentRoot "/var/www/site2" ErrorLog "/var/www/site2/logs/error.log" CustomLog "/var/www/site2/logs/access.log" vhost_combined <Directory "/var/www/site2"> Options None AllowOverride All Order allow,deny Allow from all Satisfy Any </Directory> </VirtualHost> I've also tried setting NameVirtualHost like: Listen 80 NameVirtualHost 23.88.121.82:80 NameVirtualHost 127.0.0.1:80 and the VirtualHost Directives: <VirtualHost 23.88.121.82:80> ... </VirtualHost> for both sites, but that causes the first site to fail, as well. I'm wondering if I need to set up individual IPs for each site, possibly? I have 2 more IPv4 and 3 IPv6 addresses available, if that would make a difference. Also, in the grand scheme of things, I will need to enable SSL for the first site. I've been reading that I'll need to basically just mimic the directives for listening on port 80, only on port 443, and make sure mod_ssl is enabled? EDIT: I just ran apache2 -t to test the config files that way, and got the error: apache2: bad user name ${APACHE_RUN_USER}. However, apachectl configtest returns Syntax OK. There are no other mentions of errors with the mutex anywhere else, however. I was pretty sure if there was an error with the user apache was supposed to run under, the server wouldn't start at all... EDIT 2: Restarting apache fixed the bad user name error.

  Read the article

• I cant get rid of apache2

  - by DaNieL

  It's obvious that I am a newbie with server amministration, my goal is to reach the knowledge needed to working with web services. I played with my debian server, and i messed up apache2; Now i want to completely* remove it from the server and then reinstall it as new. *for completely i really mean completely, logs, configurations, settings, everythings! I followed the steps suggested by freedom_is_chaos in this answer, and i guess apache2 is nomore installed, becose if i do apt-get remove apache2 i get this: Reading package lists... Done Building dependency tree Reading state information... Done Package apache2 is not installed, so not removed 0 upgraded, 0 newly installed, 0 to remove and 11 not upgraded. Then, i rebooted the server, and: # netstat -plant Active Internet connections (servers and established) [...] tcp6 0 0 :::80 :::* LISTEN 3467/apache2 [...] WTF? is apache2 still here? So seem: # /etc/init.d/apache2 stop Stopping web server: apache2. But: # update-rc.d remove apache2 update-rc.d: /etc/init.d/remove: file does not exist So, what is happening to my server? How can i completely and truly remove apache2 from my server?

  Read the article

• Video and LAN Cards are not recognized on Intel DG41RQ MB

  - by artyom

  Hello, My 32 bit Debian Etch with Etch-n-Half kernel 2.6.24 and Etch-n-half video driver xserver-xorg-video-intel 2.2.1-1~etchnhalf2 does not recognize my on-board LAN and Video. I can work only with VESA display. And additional PCI LAN card (that I wanted to use for Cross-X-Cabel). output of lspci 00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM Controller (rev 03) 00:01.0 PCI bridge: Intel Corporation 4 Series Chipset PCI Express Root Port (rev 03) 00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01) 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 01) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01) 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) 04:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10 According to MB Spec: Video: Intel G41 Express Chipset Graphics and Memory Controller Hub Graphics (GMCH) LAN: Realtek 8111D Gigabit Ethernet Controller LAN Support When I run dpkg-reconfigure xserver-xorg is suggest i810 driver but X does not start, it does not start with intel driver as well; only vesa. LAN I even can't find in lspci... the last Realtek card is external one 100MB card. Where to start from?

  Read the article

• Cannot open TUN/TAP dev /dev/as0t0: No such file or directory (errno=2)

  - by Mark

  I just attempted to install OpenVPN Access Server on my Debian VPS that uses OpenVZ. It installed fine, however when I try to start it from the administration panel, I get these errors: process started and then immediately exited: ['Sat Sep 22 19:14:33 2012 Cannot open TUN/TAP dev /dev/as0t0: No such file or directory (errno=2)'] service failed to start or returned error status process started and then immediately exited: ['Sat Sep 22 19:14:33 2012 Cannot open TUN/TAP dev /dev/as0t1: No such file or directory (errno=2)'] service failed to start or returned error status process started and then immediately exited: ['Sat Sep 22 19:14:33 2012 Cannot open TUN/TAP dev /dev/as0t2: No such file or directory (errno=2)'] service failed to start or returned error status process started and then immediately exited: ['Sat Sep 22 19:14:33 2012 Cannot open TUN/TAP dev /dev/as0t3: No such file or directory (errno=2)'] service failed to start or returned error status process started and then immediately exited: ['Sat Sep 22 19:14:33 2012 Cannot open TUN/TAP dev /dev/as0t4: No such file or directory (errno=2)'] service failed to start or returned error status process started and then immediately exited: ['Sat Sep 22 19:14:33 2012 Cannot open TUN/TAP dev /dev/as0t5: No such file or directory (errno=2)'] service failed to start or returned error status process started and then immediately exited: ['Sat Sep 22 19:14:33 2012 Cannot open TUN/TAP dev /dev/as0t6: No such file or directory (errno=2)'] service failed to start or returned error status process started and then immediately exited: ['Sat Sep 22 19:14:33 2012 Cannot open TUN/TAP dev /dev/as0t7: No such file or directory (errno=2)'] service failed to start or returned error status Is there a solution for this?

  Read the article

• Linux AMD-FX 8350 temperature monitoring

  - by HyperDevil

  I’m trying to get the CPU temperature for my AMD-FX8350 on Debian Squeeze. I ran sensors-detect and then sensors, but I only get my motherboard sensors (it8720-isa-0228). There are three temperature values there but I assume those are not for the CPU. it8720-isa-0228 Adapter: ISA adapter in0: +1.36 V (min = +0.00 V, max = +4.08 V) in1: +1.50 V (min = +0.00 V, max = +4.08 V) in2: +3.38 V (min = +0.00 V, max = +4.08 V) in3: +2.93 V (min = +0.00 V, max = +4.08 V) in4: +3.07 V (min = +0.00 V, max = +4.08 V) in5: +4.08 V (min = +0.00 V, max = +4.08 V) in6: +4.08 V (min = +0.00 V, max = +4.08 V) in7: +2.93 V (min = +0.00 V, max = +4.08 V) Vbat: +3.01 V fan1: 3375 RPM (min = 10 RPM) fan2: 0 RPM (min = 0 RPM) fan3: 1730 RPM (min = 10 RPM) fan5: 0 RPM (min = 0 RPM) temp1: +27.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor temp2: +53.0°C (low = +127.0°C, high = +127.0°C) sensor = thermal diode temp3: +65.0°C (low = +127.0°C, high = +90.0°C) sensor = thermal diode cpu0_vid: +0.000 V Is there anything I am missing? I also loaded the K8temp and K10temp modules and ran sensor-detect without any results. I do see this message in dmesg: hwmon-vid: Unknown VRM version of your x86 CPU

  Read the article

• NFS: Server says "authenticated mount request", but client sees "access denied"

  - by zigdon

  I have two machine, an NFS server (RHEL) and a client (Debian). The server has NFS set up, exporting a particular directory: server:~$ sudo /usr/sbin/rpcinfo -p localhost program vers proto port 100000 2 tcp 111 portmapper 100000 2 udp 111 portmapper 100024 1 udp 910 status 100024 1 tcp 913 status 100021 1 udp 53391 nlockmgr 100021 3 udp 53391 nlockmgr 100021 4 udp 53391 nlockmgr 100021 1 tcp 32774 nlockmgr 100021 3 tcp 32774 nlockmgr 100021 4 tcp 32774 nlockmgr 100007 2 udp 830 ypbind 100007 1 udp 830 ypbind 100007 2 tcp 833 ypbind 100007 1 tcp 833 ypbind 100011 1 udp 999 rquotad 100011 2 udp 999 rquotad 100011 1 tcp 1002 rquotad 100011 2 tcp 1002 rquotad 100003 2 udp 2049 nfs 100003 3 udp 2049 nfs 100003 4 udp 2049 nfs 100003 2 tcp 2049 nfs 100003 3 tcp 2049 nfs 100003 4 tcp 2049 nfs 100005 1 udp 1013 mountd 100005 1 tcp 1016 mountd 100005 2 udp 1013 mountd 100005 2 tcp 1016 mountd 100005 3 udp 1013 mountd 100005 3 tcp 1016 mountd server$ cat /etc/exports /dir *.my.domain.com(ro) client$ grep dir /etc/fstab server.my.domain.com:/dir /dir nfs tcp,soft,bg,noauto,ro 0 0 All seems well, but when I try to mount, I see the following: client$ sudo mount /dir mount.nfs: access denied by server while mounting server.my.domain.com:/dir And on the server I see: server$ tail /var/log/messages Mar 15 13:46:23 server mountd[413]: authenticated mount request from client.my.domain.com:723 for /dir (/dir) What am I missing here? How should I be debugging this?

  Read the article

• nmap on my webserver shows TCP ports 554 and 7070 open

  - by atc

  I have a webserver that hosts various websites for me. The two services that are accessible outside are SSH and Apache2. These are running on a non-standard and standard port, respectively. All other ports are closed explicitly via arno-iptables-firewall. The host is running Debian Testing. I noticed that a scan of the host using nmap produced different results from different PCs. From my laptop on my home network (behind a BT Homehub), I get the following: Not shown: 996 filtered ports PORT STATE SERVICE 80/tcp open http 554/tcp open rtsp 7070/tcp open realserver 9000/tcp open cslistener whereas scanning from a US-based server with nmap 5.00 and a Linux box in Norway running nmap 5.21 I get the following: Not shown: 998 filtered ports PORT STATE SERVICE 80/tcp open http 9000/tcp open cslistener so I hope it's my internal network or ISP that's playing up, but I cannot be sure. Running a netstat -l | grep 7070 produces nothing. Similarly for port 554. Can anyone explain the peculiarities I'm seeing?

  Read the article

• mysql.proc has gone corrupt. How can I fix it?

  - by Metalcoder

  I have a server running Debian 5.0, and MySQL. Suddendly, MySQL stopped working, and after many attempts to fix it, I decided to reinstall it. I installed MySQL 5.1.63, and when started it goes to safe mode. I made some typing, and when I executed mysql_upgrade as root, it complained: ... Running 'mysql_fix_privilege_tables'... ERROR 1548 (HY000) at line 1111: Cannot load from mysql.proc. The table is probably corrupted ERROR 1064 (42000) at line 1112: You have an error in your SQL syntax; check the manual that corresponds to your MySQL server version for the right syntax to use near 'sqlstate 'HY000' set message_text='Unexpected content found in the performance_s' at line 1 ERROR 1548 (HY000) at line 1125: Cannot load from mysql.proc. The table is probably corrupted FATAL ERROR: Upgrade failed I checked the mysql.proc table, and it's comment column was slightly different from my backup. -- My backup says: `comment` char(64) CHARACTER SET utf8 COLLATE utf8_bin NOT NULL DEFAULT '', -- But it were: `comment` text CHARACTER SET utf8 COLLATE utf8_bin NOT NULL, So, I restored my mysql database backup, and now they all match, but mysql_upgrade still trigger the same errors. I also tried do check and repair the mysql.proc table, but got no success.

  Read the article

• SpamAssassin 2010 Bug still active on my mailserver despite the offending rule being fixed - where t

  - by Ibrahim

  The SpamAssassin 2010 bug was supposed to be fixed not long after the bug became widely known, and indeed the offending rule in my /usr/share/spamassassin/72_active.cf has been updated. However, incoming messages are still being tagged by this eg: X-Spam-Status: No, score=3.188 tagged_above=-999 required=6.31 tests=[BAYES_50=0.001, FH_DATE_PAST_20XX=3.188, SPF_PASS=-0.001] Here is the relevant rule: ##{ FH_DATE_PAST_20XX header FH_DATE_PAST_20XX Date =~ /20[2-9][0-9]/ [if-unset: 2006] describe FH_DATE_PAST_20XX The date is grossly in the future. ##} FH_DATE_PAST_20XX I'm on spamassassin/3.2.5-2+lenny1.1~volatile1 on Debian Lenny, completely up to date. Any pointers on where to look to figure out what's going on? I don't know anything about SpamAssassin; someone else usually manages this but I'm free right now and am trying to figure out what the problem is because it's been annoying us for a while and we only just realized this bug was still affecting us. Update: I've lowered the score for the FH_DATE_PAST20XX rule to 0.1, both in /etc/spamassassin/local.cf and /usr/share/spamassassin/50_scores.cf and it's still giving 3.188 points for this rule. Any idea what's going on? This really has me stumped. Update 2: It seems that after restarting amavisd, it's been fixed. What's the difference between amavisd and spamd? It seems like both should not be running, or something.

  Read the article

• SpamAssassin 2010 Bug still active on my mailserver despite the offending rule being fixed - where t

  - by Ibrahim

  The SpamAssassin 2010 bug was supposed to be fixed not long after the bug became widely known, and indeed the offending rule in my /usr/share/spamassassin/72_active.cf has been updated. However, incoming messages are still being tagged by this eg: X-Spam-Status: No, score=3.188 tagged_above=-999 required=6.31 tests=[BAYES_50=0.001, FH_DATE_PAST_20XX=3.188, SPF_PASS=-0.001] Here is the relevant rule: ##{ FH_DATE_PAST_20XX header FH_DATE_PAST_20XX Date =~ /20[2-9][0-9]/ [if-unset: 2006] describe FH_DATE_PAST_20XX The date is grossly in the future. ##} FH_DATE_PAST_20XX I'm on spamassassin/3.2.5-2+lenny1.1~volatile1 on Debian Lenny, completely up to date. Any pointers on where to look to figure out what's going on? I don't know anything about SpamAssassin; someone else usually manages this but I'm free right now and am trying to figure out what the problem is because it's been annoying us for a while and we only just realized this bug was still affecting us. Update: I've lowered the score for the FH_DATE_PAST20XX rule to 0.1, both in /etc/spamassassin/local.cf and /usr/share/spamassassin/50_scores.cf and it's still giving 3.188 points for this rule. Any idea what's going on? This really has me stumped. Update 2: It seems that after restarting amavisd, it's been fixed. What's the difference between amavisd and spamd? It seems like both should not be running, or something.

  Read the article

• Apache2: not defined domains directing to the same virtual host

  - by rafaame

  I have Apache2 configured in a debian box with virtual hosts. I have several domains pointing to the box's IP address. The domains whose virtual hosts are configured works perfectly. But if I type in the browser a domain that is pointing to the box but whose the virtual host is not configured, I get to a random virtual host of another domain in the box. Not a random, but one of the virtual hosts (always the same) but I dunno why it is it. The correct would be that the domains that are not configured as virtual hosts return a hostname error or something, right? Does someone know how to fix the problem? One of my virtual hosts config file: <VirtualHost *:80> ServerAdmin [email protected] ServerName dl.domain.com DocumentRoot /var/www/dl.domain.com/public_html/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/dl.domain.com/public_html/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> My apache2.conf http://www.speedyshare.com/files/29107024/apache2.conf Thanks for the help

  Read the article

• Can reprepro accept a new version of a package into the repository?

  - by kai

  I have installed a package into my own debian package repository like so: $ sudo reprepro -b /var/packages/ubuntu includedeb maverick my-package_0.8-0_all.deb my-package_0.8-0_all.deb: component guessed as 'main' Exporting indices... I have installed my package on a few machines using apt-get install. I have now added new features to my software and would like to add a new minor version of my package to the repository so that I may update my machines using apt-get upgrade. I try to do this like so: $ sudo reprepro -b /var/packages/ubuntu includedeb maverick my-package_0.9-0_all.deb my-package_0.9-0_all.deb: component guessed as 'main' Skipping inclusion of 'my-package' '1.0-0' in 'maverick|main|i386', as it has already '1.0-0'. Skipping inclusion of 'my-package' '1.0-0' in 'maverick|main|amd64', as it has already '1.0-0'. It looks like I need to tell reprepro that this is a new version of the same package but I have no idea how to do this. I have read the reprepro man page several times and searched on the net for a couple of hours but I have not found any answers. Am I missing something? Many thanks.

  Read the article

• Why are symbolic links not working in MySQL?

  - by Eno

  I'm having an issue, I searched a lot but I'm not sure if it's related to a previous security patch. On the last version of MySQL on Debian Lenny ( 5.0.51a-24 ) I need to share one table between two db, those two db are in the same path ( /var/lib/mysql/db1 & db2 ). I created symbolic links for db2 pointing to the table in db1. When I query the same table from db2 I get this : 'ERROR 1030 (HY000): Got error 140 from storage engine' This is how it looks : test-lan:/var/lib/mysql/test3# ls -alh drwx------ 2 mysql mysql 4.0K 2010-08-30 13:28 . drwxr-xr-x 6 mysql mysql 4.0K 2010-08-30 13:29 .. lrwxrwxrwx 1 mysql mysql 28 2010-08-30 13:28 blbl.frm -> /var/lib/mysql/test/blbl.frm lrwxrwxrwx 1 mysql mysql 28 2010-08-30 13:28 blbl.MYD -> /var/lib/mysql/test/blbl.MYD lrwxrwxrwx 1 mysql mysql 28 2010-08-30 13:28 blbl.MYI -> /var/lib/mysql/test/blbl.MYI -rw-rw---- 1 mysql mysql 65 2010-08-30 13:24 db.opt I really need those symlinks, is there a way to make them working like before ? ( old MySQL-server is fine ) Thanks,

  Read the article

• Cacti not working for SNMP data sources

  - by lorenzo-s

  I installed packages cacti and snmpd on a Debian server. I'm able to display common graphs in Cacti (such as memory usage, load average, logged in users, etc) using the data templates listed as Unix. Now I want to replace these graphs with new ones using SNMP data sources, because I see there is also CPU usage and because it's not excluded I have to manage multiple hosts in the future. So, I installed snmpd on the machine and left the snmpd.conf as it is. In Cacti, I created three new data sources from SNMP templates for 127.0.0.1 host: ucd/net - CPU Usage - Nice ucd/net - CPU Usage - System ucd/net - CPU Usage - User Then I created a new graph from template ucd/net - CPU Usage, and select the three data sources in the Graph Item Fields section. Graph is now enabled and running, but empty. No data have been collected. Under Console - Devices my SNMP host is listed as up and running: System:Linux ip-xx-xx-xxx-xxx 3.2.0-23-virtual #36-Ubuntu SMP Tue Apr 10 22:29:03 UTC 2012 x86_64 Uptime: 929267 (0 days, 2 hours, 34 minutes) Hostname: ip-xx-xx-xxx-xxx Location: Sitting on the Dock of the Bay Contact: Me [email protected] In SNMP Options I left all as it is: SNMP Version: Version 1 SNMP Community: public SNMP Timeout: 500 ms Maximum OID's Per Get Request: 10 In Console - Utilities - Cacti Log I have multiple warning (two for each data source) every 5 minutes: 10/29/2012 01:45:01 PM - CMDPHP: Poller[0] Host[2] DS[18] WARNING: Result from SNMP not valid. Partial Result: U 10/29/2012 01:45:01 PM - CMDPHP: Poller[0] WARNING: SNMP Get Timeout for Host:'127.0.0.1', and OID:'.1.3.6.1.4.1.2021.4.15.0' 10/29/2012 01:45:01 PM - CMDPHP: Poller[0] Host[1] DS[9] WARNING: Result from SNMP not valid. Partial Result: U 10/29/2012 01:45:01 PM - CMDPHP: Poller[0] WARNING: SNMP Get Timeout for Host:'127.0.0.1', and OID:'.1.3.6.1.4.1.2021.11.52.0' 10/29/2012 01:40:01 PM - CMDPHP: Poller[0] Host[2] DS[19] WARNING: Result from SNMP not valid. Partial Result: U 10/29/2012 01:40:01 PM - CMDPHP: Poller[0] WARNING: SNMP Get Timeout for Host:'127.0.0.1', and OID:'.1.3.6.1.4.1.2021.4.6.0' [...] I have the feeling I'm missing something, but I cannot get it...

  Read the article

• Virtualbox HTTP load testing, host CPU overload issues

  - by aschuler

  I'm doing HTTP load testing benchmarks (using Apache Benchmark and Siege) on a small Java EE 1.7.0 / Tomcat 7.0.26 application running on a Debian Squeeze 6.0.4 x64 virtualized with Virtualbox 4.1.8. The computer host is Ubuntu 11.10 x64. I've modified those parameters in the Tomcat server.xml : <Connector port="8080" protocol="HTTP/1.1" connectionTimeout="200000" redirectPort="8443" acceptCount="2000" maxThreads="150" minSpareThreads="50" /> The application executed on the server takes around 300ms. This app is running well until a certain amount of concurrent connections like those one : ab -n 500 -c 150 http://xx.xx.xx.xx:8080/myapp/ ab -n 1000 -c 50 http://xx.xx.xx.xx:8080/myapp/ siege -b -c 100 -r 20 http://xx.xx.xx.xx:8080/myapp/ A lot of socket connection timed out happens and this completly overload the host processor (but the CPU load inside the VM is normal). Doing an htop on the host, i can see that the Virtualbox processus is running under 300% CPU and never come down even after the load test is finished. (I've allocated 4 processors to the VM, if I allocate only one processor, CPU load goes under 100%). Restarting Tomcat don't do anything, i'm forced to restart the whole VM. I've tryed to launch those ab/siege commands locally on the VM and everything goes well. I first thought it was related to a linux network limit as explained here: Running some benchmarks using ab, and tomcat starts to really slow down So I've modified those TCP parameters : echo 15 > /proc/sys/net/ipv4/tcp_fin_timeout echo 30 > /proc/sys/net/ipv4/tcp_keepalive_intvl echo 1 > /proc/sys/net/ipv4/tcp_tw_recycle echo 1 > /proc/sys/net/ipv4/tcp_tw_reuse It seems to be better, but it continues to overload the host CPU and output socket connections time out at a certain amount of concurrent connections. I'm wondering if this is not related to how Virtualbox handles external concurrent connections.

  Read the article

• Wrong CSS mime type with Roundcube 0.5 beta and nginx

  - by Julien Vehent

  I'm running into a CSS problem. This is a setup based on Debian Squeeze (nginx/0.7.67, php5/cgi) on which I installed the latest Roundcube 0.5 beta. PHP is properly processed, login works fine but the CSS files are not loaded and Firefox is throwing the following errors: Error: The stylesheet https://webmail.example.net:10443/roundcube/skins/default/common.css?s=1290600165 was not loaded because its MIME type, "text/html", is not "text/css". Source File: https://webmail.example.net:10443/roundcube/?_task=login Line: 0 Error: The stylesheet https://webmail.example.net:10443/roundcube/skins/default/mail.css?s=1290156319 was not loaded because its MIME type, "text/html", is not "text/css". Source File: https://webmail.example.net:10443/roundcube/?_task=login Line: 0 As far as I understand, nginx doesn't see the .css extension (because ofthe ?s= argument) and thus set the mime type with the default value, being text/html. Should I fix this in nginx (and how ?) or is it roundcube's related ? Edit: It seems that it's nginx related. The content-type isn't set for any other type than text/html. I had to include manually the following declarations to force CSS and JS content-types. That's ugly, and I never had the problem before... any idea ? location ~ \.css { add_header Content-Type text/css; } location ~ \.js { add_header Content-Type application/x-javascript; }

  Read the article

• Exim rejects recipient address on my domain

  - by Nicolas

  Hi, I have a dedicated server (debian) on which I have installed Exim and Dovecot. Everything worked fine until around a month ago. I tried to reinstall and reconfigure exim but I keep having all the incoming emails rejected. Outlook says: A message that you sent could not be delivered to one or more of its recipients. This is a permanent error. The following address(es) failed: [email protected] SMTP error from remote mail server after RCPT TO:: host mail.mydomain.com [94.76.##.##]: 550 relay not permitted GMAIL: Delivery to the following recipient failed permanently: [email protected] Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 550 550 relay not permitted (state 14). On the server side, my rejectlog file shows: 2011-01-04 17:09:21 H=mail-qw0-f53.google.com [209.85.216.53] F=<####@gmail.com rejected RCPT : relay not permitted ... and the mainlog file: 2011-01-04 17:00:01 1PaAEr-0007vN-DX <= root@ETC_MAILNAME U=root P=local S=869 2011-01-04 17:00:01 1PaAEr-0007vN-DX ** root@etc_mailname: Unrouteable address 2011-01-04 17:00:01 1PaAEr-0007vY-Kn Error while reading message with no usable sender address (R=1PaAEr-0007vN-DX): at least one malformed recipient address: root@ETC_MAILNAME - malformed address: _MAILNAME may not follow root@ETC 2011-01-04 17:00:01 1PaAEr-0007vN-DX Process failed (1) when writing error message to root@ETC_MAILNAME (frozen) 2011-01-04 17:09:21 no IP address found for host MAIN_RELAY_NETS (during SMTP connection from mail-qw0-f53.google.com [209.85.216.53]) 2011-01-04 17:09:21 H=mail-qw0-f53.google.com [209.85.216.53] F=<####@gmail.com rejected RCPT : relay not permitted then after the message becomes frozen: 2011-01-04 17:28:44 1PaAEr-0007vN-DX Message is frozen Thank you for your help, any idea/comment is welcomed as I am really running out of idea to fix this issue, Nicolas. Oh and the PHP mail() function does not do anything as well, would it be linked to? I think mail() uses sendmail from my php.ini.

  Read the article

• WebDAV through Apache2 permissions/missing files

  - by Strifariz

  I have a WebDAV setup on Apache2 on a server running Debian 5.0 (Lenny), which I am accessing through a mapped network drive under Windows 7. The setup appears to run fine, I receive no permission errors when copying a file to the share the first time, but the file never shows up in the directory (it's invisible, doing a ls -lha on the directory as root on the server also shows no files. When attempting to copy the file once more I am informed that the file already exists though, and I am asked if I wish to overwrite the file, when selecting "Yes" to this, I receive a permission error saying I'm not able to write to the folder. My logs aren't reporting any access violations of any kind, what could be the problem? (See log excerpt below) [17/Jan/2011:10:26:34 +0100] "PUT /1.png HTTP/1.1" 401 525 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:34 +0100] "PUT /1.png HTTP/1.1" 201 304 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:34 +0100] "LOCK /1.png HTTP/1.1" 401 525 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:34 +0100] "LOCK /1.png HTTP/1.1" 200 447 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:34 +0100] "PROPPATCH /1.png HTTP/1.1" 401 525 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:34 +0100] "PROPPATCH /1.png HTTP/1.1" 207 389 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:34 +0100] "HEAD /1.png HTTP/1.1" 401 - "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:34 +0100] "HEAD /1.png HTTP/1.1" 200 - "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:34 +0100] "PUT /1.png HTTP/1.1" 401 525 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:35 +0100] "PUT /1.png HTTP/1.1" 204 - "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:35 +0100] "PROPPATCH /1.png HTTP/1.1" 401 525 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:35 +0100] "PROPPATCH /1.png HTTP/1.1" 207 389 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:35 +0100] "UNLOCK /1.png HTTP/1.1" 401 525 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:35 +0100] "UNLOCK /1.png HTTP/1.1" 204 - "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:38 +0100] "PROPFIND / HTTP/1.1" 401 525 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600" [17/Jan/2011:10:26:38 +0100] "PROPFIND / HTTP/1.1" 207 1634 "-" "Microsoft-WebDAV-MiniRedir/6.1.7600"

  Read the article

• Pure-FTPD accounts and permissions for websites

  - by EddyR

  I'm having trouble setting up the appropriate Pure-FTPD accounts and permissions - I have the following sites setup up on my Debian server. /var/www/site1 /var/www/site2 /var/www/wordpress The permissions are 775 for folders and 664 for files. The owner is currently admin:ftpgroup Wordpress also requires special permissions for file uploads in /var/www/wordpress/wp-content/uploads What I need is: a general admin group with access to /var/www a group for each site (site1, site2, wordpress) and a group or user, not www-data (?), with permissions to write files to the wordpress upload folder I ask because restrictions on linux groups (can't have groups in groups) makes it a little bit confusing and also because many of the tutorial sites have conflicting information like, some recommend the use of www-data and some don't. Also, I'm not sure if I understand how Pure-FTP is supposed to work exactly. I create a Pure-FTPD account and assign it a directory (/var/www) and a system user (ftpuser) and group (ftpgroup): Can I assign more than 1 path? For example, if a user requires access to 2 sites. Is it better to assign ftpgroup to all ftp locations and let Pure-FTPD manage account access? Why would anyone have more than 1 ftpuser or ftpgroup? (Doesn't it mean users have access to everyone else's files if they could get there?) Sorry for so many questions at once. I've been reading lots of tutorials but I think they've ended up making me more confused!

  Read the article

• SSH session closing whilst virtualenv session stays open (I think)

  - by ing0

  I've been developing some sites using Flask recently (running on debian within a virtualenv), and when I am testing I can run it on a port, let's say post 5000. So I run the script like so: . env/bin/activate <- go into virtual environment python file.py <- run python script And I will be given this message: Running on http://0.0.0.0:5000/ So this all works great and I can access my site on this port fine. However... my rubbish ISP always does this thing where it resets something around 1am every morning. I have no idea what this is, everything runs like normal but I always get disconnected from any SSH sessions open. This leaves it running and all I can do is call: lsof -i Which will show me the process but if I kill it and then rerun it things get weird. The: Running on http://0.0.0.0:5000 message still shows but I cannot connect to it anymore. I've tried changing the port number and it seems the only thing that works is trying again later on or on another day. Now I'm assuming that something on my server resets inbetween these times and I would like to think it was maybe that virtualenv session timing out, but I cannot find out how to do this manually, does anyone know?

  Read the article

• FTP on Linux "Failed to retrieve directory listing" not firewall issue

  - by Jaka Prasnikar

  I've got an VPS in germany running Debian X64. I have very strange issue. I have ISPConfig CP installed using proftpd and I can not connect to FTP by any means. Few hours ago I've had installed DirectAdmin on CentOS same VPS and same issue. Simply when I connect to FTP server I get these: Status: Resolving address of web02.defikon.com Status: Connecting to 130.255.190.71:21... Status: Connection established, waiting for welcome message... Response: 220---------- Welcome to Pure-FTPd [privsep] [TLS] ---------- Response: 220-You are user number 1 of 50 allowed. Response: 220-Local time is now 12:15. Server port: 21. Response: 220-This is a private system - No anonymous login Response: 220-IPv6 connections are also welcome on this server. Response: 220 You will be disconnected after 15 minutes of inactivity. Command: USER default1 Response: 331 User default1 OK. Password required Command: PASS ****** Response: 230-User default1 has group access to: client0 sshusers Response: 230 OK. Current restricted directory is / Command: OPTS UTF8 ON Response: 200 OK, UTF-8 enabled Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is your current location Command: TYPE I Response: 200 TYPE is now 8-bit binary Command: PASV Error: Connection timed out Error: Failed to retrieve directory listing I even tried telnet localhost 21 and the same happends. Once I issue command "LIST" I get time out. I've tried every thing and I can't get this to work =( Please help ! P.S.: iptables is turned off.

  Read the article

• VMware virtual machine network devices malfunctioning

  - by sheepz

  I'm running Ubuntu 10.04 LTS and VMvware workstation 7.0.1 build-227600. The virtual machine i'm running in VMware is a custom distribution built on Debian Linux version 3.1. I'm still pretty much a beginner with UNIX administration. After having messed around with the vmware (changed only the name of the folder, the vmx and and other .v* files accordingly in which the .vmx was situated, and the configuration in the vmx file accordingly), the network devices on the virtual machine do not work anymore. The virtual machine is used for securely sending messages. The virtual machine: As far as I know, this perl file called proxy-gen-ifalias eth0 is responsible for properly setting up the two virtual network devices eth0 and eth1. The Virtual machine comes with a GUI interface in which I have set up two ethernet network devices, one internal, the other external. Now, after having messed around with this, the UI gives me this error message: perl proxy-gen-ifalias eth0 /etc/modprobe.d/alias-eth0 /sbin/update-modules perl proxy-gen-ifalias eth1 /etc/modprobe.d/alias-eth1 /sbin/update-modules ifdown eth0 ifdown: interface eth0 not configured ifdown eth1 ifdown: interface eth1 not configured perl proxy-gen-netcfg /etc/network/interfaces ifup eth0 SICCSIFADDR: No such device eth0: ERROR while getting interface flags: No such device SIOCSIFNETMASK: No such device eth0: ERROR while getting interface flags: No such device Failed to bring up eth0. ifconfig eth0 eth0: error fetching interface information: Device not found make: *** [/etc/network/interfaces] Error 1 ~ Here are the contents of the two perl files referred to in the message: paste.pocoo.org/show/2AMzAYhoCRZqlGY7wUFk/ proxy-gen-netcfg

  Read the article

< Previous Page | 37 38 39 40 41 42 43 44 45 46 47 48  | Next Page >