Search Results

Search found 3140 results on 126 pages for 'debian'.

Page 42/126 | < Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >

• Exim and receiving email with large recipient lists

  - by AceJordin

  I have Exim4 running on Debian configured to receive mail on multiple domains. Exim is set to forward all email that is received to one of the domains to another box. This box is configured with a catchall mailbox that everything goes in. My issue is that when an email is sent to the domain, which contains a large amount of addresses (all to the same domain, but different users), Exim will receive the single email over multiple connections. This means that the catchall mailbox receives multiple copies of the single email all containing the full recipient list. For example, I was able to reproduce it by sending an email from my gmail account that contained 500 recipients (eg [email protected]; [email protected]; [email protected]; etc. for a total of 500). Exim received the message as 20 messages (25 recipients per; appears to be a gmail server setting). So the catchall mailbox received 20 messages, each containing all 500 addresses. I'm pretty sure I understand why this is happening but is there any way I can configure Exim to only receive it once, or to combine it into one? Is there anything that can be done on my end, or am I at the mercy of the sending email server? This is causing havoc with a process that polls the catchall mailbox and parses each recipient in each email.

  Read the article

• special case ssh connection lag

  - by Hersheezy

  Setup We have a DMZ and LAN in our office that are connected to the outside with the following setup: +------+ | |------> LAN (normal office router) |Modem | | |------> DMZ (a single machine) +------+ Our internet account is with Comcast and we have 5 status IPs, one of which points to the single machine in the DMZ. Problem ssh connections initiated ANYWHERE EXCEPT the office LAN are really fast. However, from the LAN, there is about a 5 second delay. WTF?? Extra info The DMZ machine is debian 5. Executing a wget to the DMZ has no lag. When executing the following, everything up to HERE IS WHERE THE LAG IS INCURRED executes immediately. ssh -vvvv [email protected] ... debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug3: Wrote 16 bytes for a total of 1015 debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug3: Wrote 48 bytes for a total of 1063 debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/shopkins/.ssh/id_rsa (0x22440830) debug2: key: /home/shopkins/.ssh/identity ((nil)) debug2: key: /home/shopkins/.ssh/id_dsa ((nil)) debug3: Wrote 64 bytes for a total of 1127` HERE IS WHERE THE LAG IS INCURRED debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,gssapi,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering public key: /home/shopkins/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug3: Wrote 368 bytes for a total of 1495 debug1: Authentications that can continue: publickey,password debug1: Trying private key: /home/shopkins/.ssh/identity debug3: no such identity: /home/shopkins/.ssh/identity debug1: Trying private key: /home/shopkins/.ssh/id_dsa debug3: no such identity: /home/shopkins/.ssh/id_dsa debug2: we did not send a packet, disable method debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password [email protected]'s password:

  Read the article

• nVidia performance with newer X and newer driver abysmal with Compiz

  - by Nakedible

  I recently upgraded Debian to Xorg 2.9.4 and installed nvidia-glx from experimental, version 260.19.21. This was somewhat of an uphill battle as the dependencies for the experimental nvidia-glx package are still somewhat broken. I got it to work without forcing the installation of any packages and without modifying the packages. However, after the upgrade compiz performance has been abysmal. I am using the desktop wall plugin and switching viewports is really slow - takes a few seconds for each switch. In addition to this, every effect that compiz does, such as zoom animations for icons when launching applications, takes seconds. The viewport switching speed changes relative to the amount of windows on that virtual screen - empty screens switch almost at normal speed, single browser windows work almost decently, but just 4 rxvt terminals slows the switches down to a crawl. My compiz configuration should be pretty basic. Xorg is likewise configured without anything special - the only "custom" configuration is forcing the driver name to be "nvidia". I've fiddled around with the nvidia-settings and compizconfig trying different VSync settings, but none of those helped. My graphics card is: NVIDIA GPU NVS 3100M (GT218) at PCI:1:0:0 (GPU-0). This is laptop GPU that is from the Geforce GTX 200 series. Graphics card performance should naturally be no problem.

  Read the article

• ssh keys rejected each day

  - by EddyR

  I've had OpenSSH server running on my debian server for a couple weeks and all of a sudden now when I go to login the next day it rejects my ssh key and I have to manually add a new one each time. Not only that but I have the "tunneling with clear-text passwords" option enabled and the non-root (login with root is disabled) account for that is rejected too. I'm at a loss why this is happening and I can't find any ssh options that would explain it. --update-- I just changed debug level to DEBUG. But before that I'm seeing a lot of the following in auth.log Feb 1 04:23:01 greenpages CRON[7213]: pam_unix(cron:session): session opened for user root by (uid=0) Feb 1 04:23:01 greenpages CRON[7213]: pam_unix(cron:session): session closed for user root ... Feb 1 04:36:26 greenpages sshd[7217]: reverse mapping checking getaddrinfo for nat-pool-xx-xx-xx-xx.myinternet.net [xx.xx.xx.xx] failed - POSSIBLE BREAK-IN ATTEMPT! ... Feb 1 04:37:31 greenpages sshd[7223]: Did not receive identification string from xx.xx.xx.xx ... My sshd_conf file settings are: # Package generated configuration file # See the sshd(8) manpage for details # What ports, IPs and protocols we listen for Port xxx # Use these options to restrict which interfaces/protocols sshd will bind to #ListenAddress :: #ListenAddress 0.0.0.0 Protocol 2 # HostKeys for protocol version 2 HostKey /etc/ssh/ssh_host_rsa_key HostKey /etc/ssh/ssh_host_dsa_key #Privilege Separation is turned on for security UsePrivilegeSeparation yes # Lifetime and size of ephemeral version 1 server key KeyRegenerationInterval 3600 ServerKeyBits 768 # Logging SyslogFacility AUTH LogLevel DEBUG # Authentication: LoginGraceTime 120 PermitRootLogin no StrictModes yes RSAAuthentication yes PubkeyAuthentication yes #AuthorizedKeysFile %h/.ssh/authorized_keys # Don't read the user's ~/.rhosts and ~/.shosts files IgnoreRhosts yes # For this to work you will also need host keys in /etc/ssh_known_hosts RhostsRSAAuthentication no # similar for protocol version 2 HostbasedAuthentication no # Uncomment if you don't trust ~/.ssh/known_hosts for RhostsRSAAuthentication #IgnoreUserKnownHosts yes # To enable empty passwords, change to yes (NOT RECOMMENDED) PermitEmptyPasswords no # Change to yes to enable challenge-response passwords (beware issues with # some PAM modules and threads) ChallengeResponseAuthentication no # Change to no to disable tunnelled clear text passwords PasswordAuthentication yes # Kerberos options #KerberosAuthentication no #KerberosGetAFSToken no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes # GSSAPI options #GSSAPIAuthentication no #GSSAPICleanupCredentials yes X11Forwarding no X11DisplayOffset 10 PrintMotd no PrintLastLog yes TCPKeepAlive yes #UseLogin no #MaxStartups 10:30:60 #Banner /etc/issue.net # Allow client to pass locale environment variables AcceptEnv LANG LC_* Subsystem sftp /usr/lib/openssh/sftp-server UsePAM no ClientAliveInterval 60 AllowUsers myuser

  Read the article

• How to mount vfat drive on Linux with ownership other than root?

  - by Norman Ramsey

  I'm running into trouble mounting an iPod on a newly upgraded Debian Squeeze. I suspect either a protocol has changed or I've tickled a bug, which I don't know where to report. I'm trying to mount the iPod so that I have permission to read and write it. But my efforts come to nothing: $ sudo mount -v -t vfat -o uid=32074,gid=6202 /dev/sde2 /mnt /dev/sde2 on /mnt type vfat (rw,uid=32074,gid=6202) $ ls -l /mnt total 80 drwxr-xr-x 2 root root 16384 Jan 1 2000 Calendars drwxr-xr-x 2 root root 16384 Jan 1 2000 Contacts drwxr-xr-x 2 root root 16384 Jan 1 2000 Notes drwxr-xr-x 3 root root 16384 Jun 23 2007 Photos drwxr-xr-x 6 root root 16384 Jun 19 2007 iPod_Control $ sudo umount /mnt $ sudo mount -v -t vfat -o uid=nr,gid=nr /dev/sde2 /mnt /dev/sde2 on /mnt type vfat (rw,uid=32074,gid=6202) $ ls -l /mnt total 80 drwxr-xr-x 2 root root 16384 Jan 1 2000 Calendars drwxr-xr-x 2 root root 16384 Jan 1 2000 Contacts drwxr-xr-x 2 root root 16384 Jan 1 2000 Notes drwxr-xr-x 3 root root 16384 Jun 23 2007 Photos drwxr-xr-x 6 root root 16384 Jun 19 2007 iPod_Control As you see, I've tried both symbolic and numberic IDs, but the files persist in being owned by root (and only writable by root). The IDs are really mine; I've had the UID since 1993. $ id uid=32074(nr) gid=6202(nr) groups=6202(nr),0(root),2(bin),4(adm),... I've put an strace at http://pastebin.com/Xue2u9FZ, and the mount(2) call looks good: mount("/dev/sde2", "/mnt", "vfat", MS_MGC_VAL, "uid=32074,gid=6202") = 0 Finally, here's my kernel version from uname -a: Linux homedog 2.6.32-5-686 #1 SMP Mon Jun 13 04:13:06 UTC 2011 i686 GNU/Linux Does anyone know if I should be doing something different, or If there is a workaround, or If this is a bug, where it should be reported?

  Read the article

• How to set up ProxMox 1.9 on VPN?

  - by Gnudiff

  Disclaimer: I have only rudimentary knowledge of VPNs. I would love to learn about them properly, however, at the moment I really need to make stuff work on short notice. I am trying to set up a ProxMox virtualization platform in an existing network. The network currently consists of several servers which have VMWare free edition. There is some sort of VPN defined in switch. In order for VMWare management interface to be accessible, there needs to be ticked a checkbox in the network settings for VPN and entered the VPN id. I didn't notice any such configuration option during ProxMox installation, so my Proxmox VE on the same physical server, using same manual IP settings (ip/nm/gw), is not accessible. As I understand I should touch the Proxmox's underlying Debian config in /etc/network/interfaces, but I have no idea, what should I aim for: do I specify the settings for eth0, do I make a virtual interface? How to make it accessible for both ProxMox VE and underlying future VMs? I read the ProxMox installation guide, but unfortunately it presumes better understanding of VPNs than I have. A config template or similar would be appreciated. Thanks in advance.

  Read the article

• Server hang - data loss on reboot, post mortem analysis

  - by rovangju

  A development server I'm responsible for (ext3 on raid 5 w/Debian Squeeze) froze up over the weekend and I was forced to reset it, as in unresponsive from KVM/physical keyboard access, no eth devices responding, etc. Not even the backup process ran (Figures, the one time I don't check for confirmation) So after the reset, it turns out that every trace of disk IO activity that should have happened for a period of ~24H is completely gone. The log files have a big gap in the dates and times. As if the writes were never committed to disk, no processes seemed to have run. Luckily it was a weekend and nothing of value would have been lost and I don't suspect a hack. What can I do in post mortem to this event - to prevent it from ever happening again? I've seen this happen before on a completely different machine running FreeBSD. I am rounding up the disk checking tools right now - but there must be more going on! Mount options: /dev/sda1 on / type ext3 (rw,errors=remount-ro) Kernel: Linux dev 2.6.32-5-686-bigmem Disk/Inodes: 13%/3%

  Read the article

• Sharing disk volumes across OpenVZ guests to reduce Package Management Overhead

  - by andyortlieb

  Is it feasible to create a single "master" OpenVZ guest who would only be used for package management, and use something like mount --bind on several other OpenVZ guests sort of trick them into using the environment installed by the master guest? The point of this would be so that users can maintain their own containers, and yet stay in sync with the master development environment, so they'll always have the latest & greatest requirements without worrying too much about system administration. If they need to install their own packages, could put them in /opt, or /usr/local (or set a path to their home directory)? To rephrase, I would like several (developer's, for example) OpenVZ guests whose /bin, /usr (and so on...) actually refer to the same disk location as that of a master OpenVZ guest who can be started up to install and update common packages for the environment to be shared by all of this group of OpenVZ guests. For what it's worth, we're running Debian 6. Edit: I have tried mounting (bind, and readonly) /bin, /lib, /sbin, /usr in this fashion and it refuses to start the containers stating that files are already mounted or otherwise in use: Starting container ... vzquota : (error) Quota on syscall for id 1102: Device or resource busy vzquota : (error) Possible reasons: vzquota : (error) - Container's root is already mounted vzquota : (error) - there are opened files inside Container's private area vzquota : (error) - your current working directory is inside Container's vzquota : (error) private area vzquota : (error) Currently used file(s): /var/lib/vz/private/1102/sbin /var/lib/vz/private/1102/usr /var/lib/vz/private/1102/lib /var/lib/vz/private/1102/bin vzquota on failed [3] If I unmount these four volumes, and start the guest, and then mount them after the guest has started, the guest never sees them mounted.

  Read the article

• Configure nginx for multiple node.js apps with own domains

  - by udo

  I have a node webapp up and running with my nginx on debian squeeze. Now I want to add another one with an own domain but when I do so, only the first app is served and even if I go to the second domain I simply get redirected to the first webapp. Hope you see what I did wrong here: example1.conf: upstream example1.com { server 127.0.0.1:3000; } server { listen 80; server_name www.example1.com; rewrite ^/(.*) http://example1.com/$1 permanent; } # the nginx server instance server { listen 80; server_name example1.com; access_log /var/log/nginx/example1.com/access.log; # pass the request to the node.js server with the correct headers and much more can be added, see nginx config options location / { proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_set_header X-NginX-Proxy true; proxy_pass http://example1.com; proxy_redirect off; } } example2.conf: upstream example2.com { server 127.0.0.1:1111; } server { listen 80; server_name www.example2.com; rewrite ^/(.*) http://example2.com/$1 permanent; } # the nginx server instance server { listen 80; server_name example2.com; access_log /var/log/nginx/example2.com/access.log; # pass the request to the node.js server with the correct headers and much more can be added, see nginx config options location / { proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_set_header X-NginX-Proxy true; proxy_pass http://example2.com; proxy_redirect off; } } curl simply does this: zazzl:Desktop udo$ curl -I http://example2.com/ HTTP/1.1 301 Moved Permanently Server: nginx/1.2.2 Date: Sat, 04 Aug 2012 13:46:30 GMT Content-Type: text/html Content-Length: 184 Connection: keep-alive Location: http://example1.com/ Thanks :)

  Read the article

• Symbolic links not working in MySQL

  - by Eno

  I'm having an issue, I searched a lot but I'm not sure if it's related to a previous security patch. On the last version of MySQL on Debian Lenny ( 5.0.51a-24 ) I need to share one table between two db, those two db are in the same path ( /var/lib/mysql/db1 & db2 ). I created symbolic links for db2 pointing to the table in db1. When I query the same table from db2 I get this : 'ERROR 1030 (HY000): Got error 140 from storage engine' This is how it looks : test-lan:/var/lib/mysql/test3# ls -alh drwx------ 2 mysql mysql 4.0K 2010-08-30 13:28 . drwxr-xr-x 6 mysql mysql 4.0K 2010-08-30 13:29 .. lrwxrwxrwx 1 mysql mysql 28 2010-08-30 13:28 blbl.frm -> /var/lib/mysql/test/blbl.frm lrwxrwxrwx 1 mysql mysql 28 2010-08-30 13:28 blbl.MYD -> /var/lib/mysql/test/blbl.MYD lrwxrwxrwx 1 mysql mysql 28 2010-08-30 13:28 blbl.MYI -> /var/lib/mysql/test/blbl.MYI -rw-rw---- 1 mysql mysql 65 2010-08-30 13:24 db.opt I really need those symlinks, is there a way to make them working like before ? ( old MySQL-server is fine ) Thanks,

  Read the article

• Why am I seeing MailSlot Browse messages on unrouted ports of my Linux box?

  - by nmichaels

  I have a Linux box (Debian squeeze) with several NICs. The ones of interest are: eth3 - my main link to the network (dhcp on 10.20.30.0/24) eth0 - the first connection to my test network (static: 192.168.1.2) eth4 - the second connection to my test network (static: 192.168.1.1) My routing table looks like this: $ sudo route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.20.30.0 * 255.255.255.0 U 0 0 0 eth3 default 10.20.30.254 0.0.0.0 UG 0 0 0 eth3 I have the 2 test net ports connected to each other with a crossover cable and an instance of wireshark running on each port. Every once in a while, I'll see a packet like the following show up. Who could be doing this, and how do I convince them to stop? I do have Samba running on the machine (for a cifs mount) but don't see why it would be sending packets out to unrouted ports. I had a Windows VM running in VMWare Client and thought that might be causing it, but it still happens without it. What I want is totally silent interfaces so I can run some tests with Scapy over them.

  Read the article

• Which server software and configuration to retrieve from multiple POP servers, routing by address to correct user

  - by rolinger

  I am setting up a small email server on a Debian machine, which needs to pick up mail from a variety of POP servers and figure out who to send it to from the address, but I'm not clear what software will do what I need, although it seems like a very simple question! For example, I have 2 users, Alice and Bob. Any email to [email protected] ([email protected] etc) should go to Alice, all other mail to domain.example.com should go to Bob. Any email to [email protected] should go to Bob, and [email protected] should go to Alice Anything to *@bobs.place.com should go to Bob And so on... The idea is to pull together a load of mail addresses that have built up over the years and present them all as a single mailbox for Bob and another one for Alice. I'm expecting something like Postfix + Dovecot + Amavis + Spamassassin + Squirrelmail to fit the bill, but I'm not sure where the above comes in, can Postfix deal with it as a set of defined regular expressions, or is it a job for Amavis, or something else entirely? Do I need fetchmail in this mix, or is its role now included in one of the other components above. I think of it as content-filtering, but everything I read about content-filtering is focussed on detecting spam rather than routing email.

  Read the article

• NFS high CPU usage

  - by user269836

  Hello, I have a very strange issue. I have next server: Intel(R) Xeon(TM) MP CPU 3.16GHz cat /proc/cpuinfo | grep proce | wc -l 8 free -m total used free shared buffers cached Mem: 28203 27606 596 0 10789 9714 -/+ buffers/cache: 7103 21100 Swap: 24695 0 24695 RAID card *-storage description: RAID bus controller product: MegaRAID vendor: LSI Logic / Symbios Logic physical id: 7 bus info: pci@0000:13:07.0 logical name: scsi2 version: 01 width: 32 bits clock: 66MHz capabilities: storage pm bus_master cap_list rom configuration: driver=megaraid latency=32 resources: irq:134 memory:d8ff0000-d8ffffff(prefetchable) memory:df600000-df60ffff(prefetchable) HDD: 10x148Gb SCSI U320 15k - RAID5 /dev/sdb1 807G 674G 93G 88% /storage /dev/sdb1 /storage ext4 defaults,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,noatime,nodiratime,noacl,errors=remount-ro 0 1 network cards ethtool -i eth0 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ethtool -i eth1 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ifconfig bond0 Link encap:Ethernet HWaddr 00:0f:1f:ff:d6:4d inet addr:192.168.15.71 Bcast:192.168.15.255 Mask:255.255.255.0 inet6 addr: fe80::20f:1fff:feff:d64d/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:1062818202 errors:0 dropped:3918 overruns:0 frame:0 TX packets:1041317321 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10000 RX bytes:258867684559 (241.0 GiB) TX bytes:396569192650 (369.3 GiB) this server running only nfs-kernel-server uname -a Linux nas2-backup 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux Debian 6. What do I have, once per day or two, LA goes up, it can be reached around LA: 40 but if I do: nfs-kernel-server restart. Every thing is OK. But on the next day or a little bit later, LA goes up again. Servers are connected to d-link dgs 1016d with 24 GBits ports. I have tried everything to find out what the problem is. Why it's happening, but still I can not resolve this issue. Any ideas on what is happening here?

  Read the article

• how to automatically mount ~/Private using ecryptfs when logging in via ssh pubkey

  - by andreash

  Raionale: I want to be able to automatically make backups to a remote machine, which will be encrypted with ecryptfs. The title says it all: I set up ecryptfs-utils on my Debian Squeeze box, and set up one user to use it via ecryptfs-setup-private. When I log in via SSH using password authentication, the ~/Private directory automatically gets mounted. How can I achieve that ~/Private also automatically gets mounted when logging in via SSH using public key authentication? Obviously, the best solution would be if ecryptfs could somehow 'use' the SSH public key to en/decrypt the data (I know that then using the user's password would not be able to en/decrypt the data any more; this would be acceptable). Probably, this will not work. So perhaps somehow call ecryptfs-mount-private via ssh before logging in via public key? Probably, then I would need to somehow pipe the passphrase through the SSH connection, right? So I would need to store it on the source machine's file system. Not nice either. Any other ideas?

  Read the article

• Postfix / Dovecot email setup not storing email

  - by Nick Duffell

  I'm trying to setup postfix / dovecot on my debian server to use it for a mail server. I set everything up according to a tutorial on the net, and it all seemed OK. I can send emails from it, so SMTP is not a problem, however I cannot receive emails. Looking into the files in /home/nick/mail/ I can see that if I send an email to myself (from the server, to itself) the emails are there, but are put straight into the Deleted Messages folder. I don't know why this is. When I send an email from another mail account (not on this server), the emails are nowhere to be found. Also, looking at the log file /var/log/mail.log all seems to be OK, I get the following when I receive an email, which looks OK to me: Nov 7 22:47:22 nickduffell postfix/local[17825]: 05B1173581A6: to=, relay=local, delay=0.37, delays=0.31/0.02/0/0.03, dsn=2.0.0, status=sent (delivered to mailbox) Any ideas? Thanks EDIT: I should also add that although the emails I send myself are in the Deleted Messages folder, and in my mail client I can see that "Trash" has 3 items, I cannot download them in my mail client...

  Read the article

• Fix for php 5.3.9 libxsl security "bug" fix

  - by Question Mark

  just this morning i updated my debian server to php 5.3.9 , change log (last item in list) has a fix for this bug and now when running any hosted site using XSL transforms i get: Warning: XSLTProcessor::transformToXml(): Can't set libxslt security properties, not doing transformation for security reasons I'm not using any <sax:output> tags in my xslt at all. Does anybody have any information on this, current chatter about it is thin, so i'm i little lost. Using the suggestion about switching ini settings on and off either side of -transformToXml(): ini_set("xsl.security_prefs", XSL_SECPREFS_NONE) or $xsl->setSecurityPreferences(XSL_SECPREFS_NONE) brings me back to the same error Many thanks. Progress: - Upgrading libxml and recompiling libxslt against the new version was a good suggestion, though has not fixed the issue. - Compiling the latest php5.3 snapshot does not fix the issue. Solution: I'm unsure what actually solved this, very sorry for anyone else having the same problem. firstly i upgraded libxml, then applied a few patches, then went into php source for the xsl parser and added some debugging and a few tweaks, after a few compiles getting the configure args right the error went away and wasn't reproducible. I would definitely recommend upgrading libxml as Petr suggested below and then grabbing the latest snapshot from php.net.

  Read the article

• Git clone/push/pull - where's that username comes from?

  - by Kuroki Kaze

  I've set up gitosis and able to pull/push through ssh. Gitosis is installed on Debian Lenny server, I'm using git from windows machine (msysgit). The strange thing, if I enable loglevel = DEBUG in gitosis.conf, I see something like this when doing any actions with gitosis server: D:\Kaze\source\test-project>git pull origin master DEBUG:gitosis.serve.main:Got command "git-upload-pack 'test_project.git'" DEBUG:gitosis.access.haveAccess:Access check for '[email protected]' as 'writable' on 'test_project.git'... DEBUG:gitosis.access.haveAccess:Stripping .git suffix from 'test_project.git', new value 'test_project' DEBUG:gitosis.group.getMembership:found '[email protected]' in 'test' DEBUG:gitosis.access.haveAccess:Access ok for '[email protected]' as 'writable' on 'test_project' DEBUG:gitosis.access.haveAccess:Using prefix 'repositories' for 'test_project' DEBUG:gitosis.serve.main:Serving git-upload-pack 'repositories/test_project.git' From 192.168.175.128:test_project * branch master -> FETCH_HEAD Already up-to-date. Question is: why am I *[email protected]? This email is in global user.email config variable, too. Yesterday, when the gitosis was installed, it seen me as kaze@KAZE, this is the name under which I was added to gitosis-admin group (and it worked). But today git (or gitosis) started to see me as [email protected]. This is true for all repositories I push or clone. I had to add this address to gitosis.conf directly on server to be able to edit configs again (it worked). There is 2 public keys in keydir: [email protected] and [email protected], their content is identical and they have kaze@KAZE at end. Origin URL looks like git@lennyserver:test_project. Now, the question is - why Git (or gitosis) suddenly decided to call me by email instead of name@machinename? I've changed a couple things trying to set up Gitosis (updated git on server to 1.6.0 for example), but maybe I broke something in my local git installation?

  Read the article

• Surprising corruption and never-ending fsck after resizing a filesystem.

  - by Steve Kemp

  System in question has Debian Lenny installed, running a 2.65.27.38 kernel. System has 16Gb memory, and 8x1Tb drives running behind a 3Ware RAID card. The storage is managed via LVM. Short version: Running a KVM guest which had 1.7Tb storage allocated to it. The guest was reaching a full-disk. So we decided to resize the disk that it was running upon We're pretty familiar with LVM, and KVM, so we figured this would be a painless operation: Stop the KVM guest. Extend the size of the LVM partition: "lvextend -L+500Gb ..." Check the filesystem : "e2fsck -f /dev/mapper/..." Resize the filesystem: "resize2fs /dev/mapper/" Start the guest. The guest booted successfully, and running "df" showed the extra space, however a short time later the system decided to remount the filesystem read-only, without any explicit indication of error. Being paranoid we shut the guest down and ran the filesystem check again, given the new size of the filesystem we expected this to take a while, however it has now been running for 24 hours and there is no indication of how long it will take. Using strace I can see the fsck is "doing stuff", similarly running "vmstat 1" I can see that there are a lot of block input/output operations occurring. So now my question is threefold: Has anybody come across a similar situation? Generally we've done this kind of resize in the past with zero issues. What is the most likely cause? (3Ware card shows the RAID arrays of the backing stores as being A-OK, the host system hasn't rebooted and nothing in dmesg looks important/unusual) Ignoring brtfs + ext3 (not mature enough to trust) should we make our larger partitions in a different filesystem in the future to avoid either this corruption (whatever the cause) or reduce the fsck time? xfs seems like the obvious candidate?

  Read the article

• Problem with single quotes in man pages

  - by Peter

  When I ssh into my Debian Lenny server and open a man page, single quotes appear to be messed up. Example from the man page of apt-get: If no package matches the given expression and the expression contains one of ´.´, ´?´ or ´*´ then it is assumed to be a POSIX regular expression, and it is applied to all package names in the database. Any matches are then installed (or removed). Note that matching is done by substring so ´lo.*´ matches ´how-lo´ and ´lowest´. If this is undesired, anchor the regular expression with a ´^´ or ´$´ character, or create a more specific regular expression. I'm on Mac OS X and using xterm. If I use Terminal, the problem doesn't happen. My locale is configured correctly as far as I can see: $ locale LANG=en_US.UTF-8 LC_CTYPE="en_US.UTF-8" LC_NUMERIC="en_US.UTF-8" LC_TIME="en_US.UTF-8" LC_COLLATE="en_US.UTF-8" LC_MONETARY="en_US.UTF-8" LC_MESSAGES="en_US.UTF-8" LC_PAPER="en_US.UTF-8" LC_NAME="en_US.UTF-8" LC_ADDRESS="en_US.UTF-8" LC_TELEPHONE="en_US.UTF-8" LC_MEASUREMENT="en_US.UTF-8" LC_IDENTIFICATION="en_US.UTF-8" LC_ALL= I'm not sure what's wrong with my environment, and I have no idea what to check next. I'd appreciate help.

  Read the article

• How to stop my VPS from picking up ARP reqs it is not supposed to?

  - by Charles Stewart

  Machine: Xen-3.0 image running stable Debian Linux 2.6.18, pretty vanilla. My VPS provider asks me to deal with some trouble my image is causing, namely handling IP addresses it is not supposed to: The problem is that your server seems to be configured to use IPs that have not been appointed to you. Your server responds to ARP requests for the IPs 81.171.111.219 and 81.171.111.218. But you are not allowed to use those. Not explicitly, as far as I can tell! At least, nothing under /etc or /var/tmp mentions these IP addresses. But arp -v says something I can't make sense of: Address HWtype HWaddress Flags Mask Iface 81.171.111.1 ether 00:0C:DB:E3:80:00 C eth0 Entries: 1 Skipped: 0 Found: 1 What is it listening to? The possibilities seem to be: It's not my fault: my VPS providers have overlooked something. What might that be? 81.171.111.1 means I'm happy listening in on ARP requests that I shouldn't be: how do I change this? In any case, what does this mean? I'm looking in completely the wrong place for information on what my image is doing. Where should I be looking?

  Read the article

• CUPS causes printer to click and doesn't print

  - by Pez Cuckow

  I'm suffering a strange problem with my Cannon iP4850 when trying to use CUPS on a Raspberry Pi (this is not RPi specific, please do not vote to move it). When I plug the printer into my Laptop (OSX) or my Desktop W7 it identifies as a iP4800 and prints perfectly. So I plug it into the Pi (running debian), set it up in CUPS enable sharing and can now see the iP4800 series shared on the network. However if I print to it (using AirPrint etc...); the file gets to CUPS safely (shows in the queue) but when it tries to print the printer clicks (like a loud thunk) 3/4 times and then gives in, with a double amber flashing light. In cups it shows as job completed. Do you know why using the pi and cups would cause what appears to be a hardware fault and what I can do to fix the problem or to provide further debug info? Thanks for your time! Description: Canon iP4800 series Location: Lounge Driver: Canon PIXMA iP4800 - CUPS+Gutenprint v5.2.9 (color, 2-sided printing) Connection: usb://Canon/iP4800%20series?serial=2239B2 Note: I've tried deleting and re-adding the printer to the Laptop, Desktop and PI and the results are always the same Log for plugging in printer and printing (attempting to) something until the printer turned off again pi@pezpi /var/log $ dmesg [ 7284.176336] usb 1-1.2: new high speed USB device number 8 using dwc_otg [ 7284.279703] usb 1-1.2: New USB device found, idVendor=04a9, idProduct=10d5 [ 7284.279750] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7284.279771] usb 1-1.2: Product: iP4800 series [ 7284.279786] usb 1-1.2: Manufacturer: Canon [ 7284.279800] usb 1-1.2: SerialNumber: 2239B2 Setting cups to verbose: Change loglevel in cupsd.conf to debug (or debug2) pi@pezpi /var/log $ sudo vim /etc/cups/cupsd.conf pi@pezpi /var/log $ sudo /etc/init.d/cups restart [ ok ] Restarting Common Unix Printing System: cupsd. pi@pezpi /var/log $ Log from $ /var/log/cups/error_log is at http://pastebin.com/7VZMRMrG (too large to post here) The log contains - in order (deleted the log and then did the beneath) Restarting the cups server Attempting to print a test page x2 Printing from 192.168.1.90 via AirPrint Printing from 192.168.1.90 via Network Print Turning the printer off and on again

  Read the article

• Millions of files in php's tmp error - how to delete?

  - by Jonatan Littke

  Hey. I've got a tmp-folder with 14 million php session files in my home directory. At least that's what I think it is, it's not like I could ls it or anything. How can I empty this folder? I've tried using find with the -exec rm {} \; commands but that didn't work. ls 'sess_0*' | xargs rm did neither. I'm currently running rm -rf tmp but after two hours the folder appears to be the same size. REFERENCE INFO: I suddenly encountered an error where SESSIONS could no longer be written to disk: [Mon Apr 19 19:58:32 2010] [warn] mod_fcgid: stderr: PHP Warning: Unknown: open(/var/www/clients/client1/web1/tmp/sess_8e12742b62aa68a3f9476ec80222bbfb, O_RDWR) failed: No space left on device (28) in Unknown on line 0 [Mon Apr 19 19:58:32 2010] [warn] mod_fcgid: stderr: PHP Warning: Unknown: Failed to write session data (files). Please verify that the current setting of session.save_path is correct (/var/www/clients/client1/web1/tmp) in Unknown on line 0 I ran: $ df -h Filesystem Size Used Avail Use% Mounted on /dev/md0 457G 126G 308G 29% / tmpfs 1.8G 0 1.8G 0% /lib/init/rw udev 10M 664K 9.4M 7% /dev tmpfs 1.8G 0 1.8G 0% /dev/shm But as you can see, the disk isn't full. So I had a look in the syslog which says the following 20 times per second: kernel: [19570794.361241] EXT3-fs warning (device md0): ext3_dx_add_entry: Directory index full! This led me thinking to a full folder, obviously, but since my web folder only has 60k files (having counted them), I guessed it was the tmp folder (the local one, for this instance of php) that messed things up. Some commands I ran: $ sudo ls sess_a* | xargs rm -f bash: /usr/bin/sudo: Argument list too long find . -exec rm {} \; rm: cannot remove directory '.' find: cannot fork: Cannot allocate memory I'm running Debian Lenny, php5, ISPConfig, SuEXEC and Fast-CGI.

  Read the article

• Directory directive: AuthType None but still need an AuthProvider?

  - by Steffen Winkler

  For now I just need the server to let me download files from one specific folder (in my case I chose /opt/myFolder for that task) Distribution is Debian 6.0 *edit_start* Apache version is 2.4, according to their official documentation, the Order/Allow clauses are deprecated and should not be used anymore I'm an idiot: Apache version is 2.2. *edit_end* My directory directives in apache2.conf look like this: <IfModule dir_module> DirectoryIndex index.html index.htm index.php </IfModule> ServerRoot "/etc/apache2" DocumentRoot "/opt/myFolder" <Directory /> Options FollowSymLinks AuthType None AllowOverride None Require all denie </Directory> <Directory "/opt/myFolder/*"> Options FollowSymLinks MultiViews AllowOverride None AuthType None Require all allow </Directory> When I try to access a file inside that folder (http://myserver.de/aTestFile.zip) I get an Internal Server Error. Also Apache writes the following error into it's log: configuration error: couldn't check user. Check your authn provider!: /aTestFile.zip Why would I need an authn provider if I don't want any authentication? Also I hope someone can explain to me what kind of AuthenticationProvider I'd need for that. Everytime I search for those things I get pointed at people asking how to protect files/directories with passwords or restrict access to some IP addresses, which doesn't really help me. ok, since I've Apache version 2.2, here is the error I get when using the Order/Deny/Allow commands instead of AuthType/Require: Invalid command 'Order', perhaps misspelled or defined by a module not included in the server configuration.

  Read the article

• Cron won't use msmtp to send emails in case of failed cronjob

  - by Glister

  I'm trying to configure a machine so that it will send me an email if one of the cronjobs output something in case of an error. I'm using Debian Wheezy. Cron is working normally (without the email functionality). msmtp is installed and configured. Have already symlinked /usr/{bin|sbin}/sendmail to /usr/bin/msmtp. I can send email by using: echo "test" | mail -s "subject" [email protected] or by executing: echo "test" | /usr/sbin/sendmail Without the symlink (/usr/sbin/sendmail) cron will tell me that: (CRON) info (No MTA installed, discarding output) With the symlinks I get: (root) MAIL (mailed 1 byte of output; but got status 0x004e, #012) Can you suggest how to config the cron/msmtp pair? Thanks! EDIT: Note: I've written "msmtpd" by mistake. Its not a daemon but rather an SMTP client named just "msmtp" (without the "d" ending). It is executed on demand and it is not running in the background all the time. When I try to send an email by using msmtp like that it works: echo "test" | msmtp [email protected] On the far side, in the logs of the SMTP server I read: Nov 2 09:26:10 S01 postfix/smtpd[12728]: connect from unknown[CLIENT_IP] Nov 2 09:26:12 S01 postfix/smtpd[12728]: 532301C318: client=unknown[CLIENT_IP], sasl_method=CRAM-MD5, [email protected] Nov 2 09:26:12 S01 postfix/cleanup[12733]: 532301C318: message-id=<> Nov 2 09:26:12 S01 postfix/qmgr[2404]: 532301C318: from=<[email protected]>, size=191, nrcpt=1 (queue active) Nov 2 09:26:12 S01 postfix/local[12734]: 532301C318: to=<[email protected]>, orig_to=<[email protected]>, relay=local, delay=0.62, delays=0.59/0.01/0/0.03, dsn=2.0.0, status=sent (delivered to command: IFS=' ' && exec /usr/bin/procmail -f- || exit 75 #1001) Nov 2 09:26:12 S01 postfix/qmgr[2404]: 532301C318: removed Nov 2 09:26:13 S01 postfix/smtpd[12728]: disconnect from unknown[CLIENT_IP] And the Email is delivered to the target user. So it looks like that the msmtp client is working properly. It has to be something in the cron/msmtp integration, but I have no clue what that thing might be. Can you help me?

  Read the article

• NGINX server_name issues

  - by Unai

  I have the following simple server block on NGINX: server { listen 80; listen 8090; server_name domain.com; autoindex on; root /home/docroot; location ~ \.php$ { include /usr/local/nginx/conf/fastcgi_params; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /home/docroot$fastcgi_script_name; fastcgi_pass 127.0.0.1:9000; } } After I include the relevant settings on my hosts file I get the following (unexpected) behavior: http: //domain.com/ and http: //domain.com:8090/ work fine; http: //domain.com:8090/future-cell-phone-technology-01-150x150.jpg works; http: //domain.com/future-cell-phone-technology-01-150x150.jpg - ERROR! "The connection was reset" (note.- added a space after http: to avoid link protection but this is not really promoting anything) I've been troubleshooting (3) for a couple hours and I'm unable to identify the culprit. I'm running NGINX 1.0.10 (latest stable) on Debian 6.0.2 32 bits. This NGINX instance runs another 40 or 50 sites with no problems.

  Read the article

< Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >