Search Results

Search found 24097 results on 964 pages for 'freebsd update'.

Page 41/964 | < Previous Page | 37 38 39 40 41 42 43 44 45 46 47 48  | Next Page >

• CARP: two machines think they're the master, but only on one interface

  - by Conor McDermottroe

  I have two machines, each configured identically as a firewall/load balancer for a busy website. I have set them up with CARP and pfsync on both the internal and external interfaces. The internal interface is behaving as expected (primary listed as MASTER and secondary listed as BACKUP) On both machines, the network interfaces are as follows: em0 - External interface bge0 - Internal interface bge1 - Crossover connection between both machines carp0 - Shared external interface for CARP carp1 - Shared internal interface for CARP I've rewritten the IP addresses and MAC addresses below. The networks are as follows: 10.0.1.0/24 - External network 10.0.2.0/24 - Internal network 10.0.3.0/24 - Crossover network Here's the output from ifconfig on the primary: em0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4> ether [SNIP] inet 10.0.1.10 netmask 0xffffff00 broadcast 10.0.1.255 media: Ethernet 100baseTX <full-duplex> status: active bge0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.2.10 netmask 0xffffff00 broadcast 10.0.2.255 media: Ethernet 1000baseT <full-duplex> status: active bge1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.3.10 netmask 0xffffff00 broadcast 10.0.3.255 media: Ethernet 1000baseT <full-duplex> status: active lo0: flags=80c9<UP,LOOPBACK,RUNNING,NOARP,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 pflog0: flags=141<UP,RUNNING,PROMISC> metric 0 mtu 33152 pfsync0: flags=0<> metric 0 mtu 1460 pfsync: syncdev: bge1 syncpeer: 10.0.3.11 maxupd: 128 carp0: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.1.5 netmask 0xffffff00 carp: MASTER vhid 1 advbase 1 advskew 0 carp1: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.2.5 netmask 0xffffff00 carp: MASTER vhid 2 advbase 1 advskew 0 And here's the /etc/rc.conf excerpt from the primary: defaultrouter="10.0.1.1" network_interfaces="em0 bge0 bge1 lo0 pfsync0" cloned_interfaces="carp0 carp1" ifconfig_em0="inet 10.0.1.10 netmask 255.255.255.0 media 100BaseTX mediaopt full-duplex" ifconfig_bge0="inet 10.0.2.10 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_bge1="inet 10.0.3.10 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_carp0="vhid 1 pass [SNIP] 10.0.1.5/24" ifconfig_carp1="vhid 2 pass [SNIP] 10.0.2.5/24" pfsync_enable="YES" pfsync_syncdev="bge1" pfsync_syncpeer="10.0.3.11" And here's the output on the secondary: em0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4> ether [SNIP] inet 10.0.1.11 netmask 0xffffff00 broadcast 10.0.1.255 media: Ethernet 100baseTX <full-duplex> status: active bge0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.2.11 netmask 0xffffff00 broadcast 10.0.2.255 media: Ethernet 1000baseT <full-duplex> status: active bge1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.3.11 netmask 0xffffff00 broadcast 10.0.3.255 media: Ethernet 1000baseT <full-duplex> status: active lo0: flags=80c9<UP,LOOPBACK,RUNNING,NOARP,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 pflog0: flags=141<UP,RUNNING,PROMISC> metric 0 mtu 33152 pfsync0: flags=0<> metric 0 mtu 1460 pfsync: syncdev: bge1 syncpeer: 10.0.3.10 maxupd: 128 carp0: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.1.5 netmask 0xffffff00 carp: MASTER vhid 1 advbase 1 advskew 20 carp1: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.2.5 netmask 0xffffff00 carp: BACKUP vhid 2 advbase 1 advskew 20 And here's the /etc/rc.conf excerpt from the secondary: defaultrouter="10.0.1.1" network_interfaces="em0 bge0 bge1 lo0 pfsync0" cloned_interfaces="carp0 carp1" ifconfig_em0="inet 10.0.1.11 netmask 255.255.255.0 media 100BaseTX mediaopt full-duplex" ifconfig_bge0="inet 10.0.2.11 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_bge1="inet 10.0.3.11 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_carp0="vhid 1 pass [SNIP] advskew 20 10.0.1.5/24" ifconfig_carp1="vhid 2 pass [SNIP] advskew 20 10.0.2.5/24" pfsync_enable="YES" pfsync_syncdev="bge1" pfsync_syncpeer="10.0.3.10" What I don't understand is, the carp status on carp0 is MASTER on both machines when the status on carp1 is as it should be (MASTER on the primary and BACKUP on the secondary). What am I missing? Where should I be looking for clues?

  Read the article

• Update BIOS on Sun Fire X4150 server

  - by Massimo

  I have some Sun Fire X4150 servers with a very old BIOS release (1ADQW015), which seems to have some compatibility problems with WMware ESX Server 3.5 and Windows 2008 R2 virtual machines; so I want to update the BIOS on them. The problem: according to this page, if your servers run ELOM (mine do), you first need to update to the latest ELOM release, then to the interim transition release, then finally you can update to the latest one. Ok, I'm willing to do that... but it looks like Sun (now Oracle) will happily let you download the latest firmware DVD (3.3.0), but it will not let you download the transition release (2.0) if you don't have a support contract. Well, I actuall don't care at all about the servers' management controllers (we don't even use them), so upgrading from ELOM to ILOM is totally irrelevant to me; but I need to update the servers' BIOS. So my question is: can I update the servers' BIOS to the latest version without doing the full ELOM-to-ILOM migration, or will this not work (or even make the servers unusable)? Do BIOS versions and SP ones need to be matched, or can one be updated without bothering with the other? Bonus question: if this whole ELOM-to-ILOM thing actually is needed in order to update the BIOS, can that 2.0 CD-ROM be obtained without having a support contract with Sun/Oracle (which we are definitely not going to sign, being that quite old hardware)? Update: I tried upgrading only the BIOS on one of the servers, and it didn't boot anymore. So it really looks like a full firmware upgrade is needed, and the management controller and BIOS versions should be kept in sync. So... where can I find that *&!£%$% 2.0 CD-ROM? Or at least the transition firmware that can be found on it?

  Read the article

• Apache doesn't autostart because vpn isn't up yet.

  - by Col. Shrapnel

  I have a FreeBSD8 server, and VPN connection to my ISP. I use mpd5 and it works fine. A have an Apache server whch works fine, if I start it manually, after VPN is get up. But when I add it to rc.conf autostart, it fail to start, saying (49) can't assign requested address: make_sock could not bind to address I suppose it's because VPN isn't up yet and no IP address assigned to the interface which i set in the Listen directive in the httpd.conf. If i set Listen to the existing 127.0.0.1, it fail to serve wan requests. Is there a solution, either to delay apache autostart or configure it some different?

  Read the article

• readlink: illegal option -- f

  - by Scott

  Recently the script was working fine, but from some days I'm receiving such message, while running the readlink -f "$0" command: readlink: illegal option -- f usage: readlink [-n] [file ...] I was running the following code to debug: #!/bin/sh DIR=`pwd` RLPATH=`which readlink` RLOUT=`readlink -f -- "${0}"` DIROUT=`dirname -- ${RLOUT}` echo "dir: ${DIR}" echo "path: ${PATH}" echo "path to readlink: ${RLPATH}" echo "readlink output: ${RLOUT}" echo "dirname output: ${DIROUT}" Output: # ./debug.sh readlink: illegal option -- f usage: readlink [-n] [file ...] usage: dirname string [...] dir: /home/svr path: /sbin:/bin:/usr/sbin:/usr/bin:/usr/games:/usr/local/sbin:/usr/local/bin:/root/bin path to readlink: /usr/bin/readlink readlink output: dirname output: What is wrong ?

  Read the article

• Notebook Operating System with extreme support cycles/security updates

  - by leto

  Hello there, after reading the announcements about Mac OS X "Lion" and Apples political decision, I've had enough. I'm a longtime Apple User since 1992, have always felt at home there, but am trying to switch to alternative Operating System since a year. I've also been working with Unix machines since 2001, so I'm looking in one of the free Unices or a Linux. Since I last looked at the desktop in 2002 choke much has changed, it seems. So I'm lost once more in the war between desktop environments and software. To be honest: I don't care what it's name is, I want to get my job done. Here's what I set me as landmark for an operating system/software to be considered: Has to be atleast four years old Has to supply security updates for current release for atleast a year Production quality stability for the whole desktop environment (!) No f****g commercial stuff that tends to supply me with privacy invading App Store or Cloud space So far I'm running a MacBook from 2007, 4 Gig memory, 250 Gig disk and I need: IMAPs for Mail since 1995 Webbrowser sic Shell Keeping current with Updates/Upgrades with no more than 5 Minutes spent in entering commands (makes it hard for OpenBSD ;-) ) A desktop filemanger would be nice, but is a bonus. What can you suggest as operating system? The one with the longest support cycles and best chance to survive the next 10 years will win a new user, even sending patches when needed :-) Greets

  Read the article

• FreeNas running on ESXi - sometimes gets very slugish.

  - by Luma

  Hello everyone, I have a ESXi server (dual quad core, 8GB of DDR3 ram, 6x 1TB WD Blacks running in RAid 5 on the PErc 6/i controller. I have a 64bit freenas VM running, on this VM I keep about 200Gigs of stuff that my windows machines access. every now and then the throughput of this VM just dies, for example right now it can't even handle streaming a song and when I tried to transfer a folder the speed goes from 10-400KB/s. Might I add at this point that the ESXi box has dual gigabit network cards plugged into a good solid gigabit switch and other linux and windows VM's are just fine I have seen speeds over 90MB/s (frequently) The server still has ram left over (plenty actually) and cpu is very low (500-1000mhz) any ideas what could cause this? thanks. Luc

  Read the article

• what does the @ symbol mean in ls -l directory listing?

  - by Andrew Arrow

  When I run ls -l on my mac I see two .yml files: -rw-r--r-- 1 aa staff 6 Apr 15 05:50 s1.yml -rw-r--r--@ 1 aa staff 362 Apr 15 05:49 s3.yml same owner, same permissions but one has a @ at the end of the permisions. The one with the @ shows up in my editor, the one without does not. So there must be some significance. How can I turn on the @ for the file without it? I selected the files in the finder and did get info and everything looks identical between the two files.

  Read the article

• How to split registration and media?

  - by Stackfan

  I have a SIP project. Where i will have SIP server running. Server will do following: will only do routing and receive incoming calls But the audio/video will be peer 2 peer Can this be done with Asterisk? Only the media i have to split but the registration will be with Server. Tools: A) server with SIP B) One PC with SIP client C) Anoher PC with SIP client My goal is: B and C gets connected via A and audio/video packets are not via A

  Read the article

• How can I update generic non-pnp monitor?

  - by njk

  Background I've been running a KVM switch with my monitor at 1920 x 1080 over VGA for over a year. Did a Windows Update on 12/11/12 which did the following: Update for Windows 7 for x64-based Systems (KB2779562) Security Update for Windows 7 for x64-based Systems (KB2779030) Cumulative Security Update for Internet Explorer 8 for Windows 7 for x64-based Systems (KB2761465) Windows Malicious Software Removal Tool x64 - December 2012 (KB890830) Security Update for Windows 7 for x64-based Systems (KB2753842) Security Update for Windows 7 for x64-based Systems (KB2758857) Security Update for Windows 7 for x64-based Systems (KB2770660) After a restart, my extended monitor was dark. I attempted to reset the extended display configuration, and noticed my monitor was being detected as a Generic Non-PnP Monitor: I uninstalled, downloaded new, and re-installed display drivers. Nothing. I attempted to unplug my monitor from the power for 15 minutes. Nothing. I followed some of the suggestions on this thread; specifically DanM's which suggested to create a new *.inf file and replace that in Device Manager. Device Manager said the "best driver software for your device is already installed". The only thing that works is when the monitor is directly attached to the laptop. This obviously is not what I want. My thought is to somehow remove the Generic Non-PnP Monitor from registry. How would I accomplish this and would this help? Any other suggestions? Relevant Hardware ASUS VE276 Monitor TRENDnet 2-Port USB KVM Switch (TK-207K) HP Laptop w/ ATI Radeon HD 4200 Screens

  Read the article

• Would NetBSD be a good choice for a web server?

  - by Alexander

  I've the choice of crafting a NetBSD image for a Xen VPS host, and was just wanting to play around as I like BSD and wished to use it for my general web hosting. I will be hosting a low-mid traffic website and maybe a few other simple services. Do you think NetBSD would be a sufficient choice, in terms of general performance of multiple system users and fair amount of traffic to Apache compared to what Linux could normally handle? I am concerned if I do start to really like it and keep it, I may be limiting myself if I am to move further with my web host and get more traffic (and maybe a lot of FTP access and user shell accounts) Ken

  Read the article

• Regarding some Update Stored procedure

  - by Serenity

  I have two Tables as follows:- Table1:- ------------------------------------- PageID|Content|TitleID(FK)|LanguageID ------------------------------------- 1 |abc |101 |1 2 |xyz |102 |1 -------------------------------------- Table2:- ------------------------- TitleID|Title |LanguageID ------------------------- 101 |Title1|1 102 |Title2|1 ------------------------ I don't want to add duplicates in my Table1(Content Table). Like..there can be no two Pages with the same Title. What check do I need to add in my Insert/Update Stored Procedure ? How do I make sure duplicates are never added. I have tried as follows:- CREATE PROC InsertUpdatePageContent ( @PageID int, @Content nvarchar(2000), @TitleID int ) AS BEGIN IF(@PageID=-1) BEGIN IF(NOT EXISTS(SELECT TitleID FROM Table1 WHERE LANGUAGEID=@LANGUAGEID)) BEGIN INSERT INTO Table1(Content,TitleID) VALUES(@Content,@TitleID) END END ELSE BEGIN IF(NOT EXISTS(SELECT TitleID FROM Table1 WHERE LANGUAGEID=@LANGUAGEID)) BEGIN UPDATE Table1 SET Content=@Content,TitleID=@TitleID WHERE PAGEID=@PAGEID END END END Now what is happening is that it is inserting new records alright and won't allow duplicates to be added but when I update its giving me problem. On my aspx Page I have a drop down list control that is bound to DataSource that returns Table 2(Title Table) and I have a text box in which user types Page's content to be stored. When I update, like lets say I have a row in my Table 1 as shown above with PageID=1. Now when I am updating this row, like I didn't change the Title from the drop down and only changed Content in the text box, its not updating the record ..and when Stored procedure's Update Query does not execute it displays a Label that says "Page with this title exists already." So whenever I am updating an existing record that label is displayed on screen.How do I change that IF condition in my Update Stored procedure?? EDIT:- @gbn :: Will that IF condition work in case of update? I mean lets say I am updating the Page with TitleID=1, I changed its content, then when I update, it's gonna execute that IF condition and it still won't update coz TitleID=1 already exits!It will only update if TitleID=1 is not there in Table1. Isn't it? Guess I am getting confused. Please answer.Thanks.

  Read the article

• WiX installer - Update scenario Custom UI

  - by iulianchira

  For my application I have an .msi developed with WiX. For the update scenario I want to do the following: if the installed version is never than the update version display an error if the installed version is older than the update version show a button with text Update if the installed version is the same as the update version show a button with text Repair I have found how to define custom UI dialogs, but if I create a dialog with all these controls (Error label, Update/Repair buttons) how can I display just the appropriate one according to the situation.

  Read the article

• TeamSpeak3 libraries

  - by Scott

  I've downloaded the TeamSpeak 3 server from their official website (it's 64 bit, as my dedicated server is 64 bit too). This is what I get,when I'm trying to run the server: Starting the TeamSpeak 3 server TeamSpeak 3 server started, for details please view the log file /libexec/ld-elf.so.1: scott# /lib/libiconv.so.3: unsupported file layout Whats wrong? /libexec/ld-elf.so.1 exists, same as the second one, is there any solution for that?

  Read the article

• TeamSpeak3 libraries

  - by Scott

  I've downloaded the TeamSpeak 3 server from their official website (it's 64 bit, as my dedicated server is 64 bit too). This is what I get,when I'm trying to run the server: Starting the TeamSpeak 3 server TeamSpeak 3 server started, for details please view the log file /libexec/ld-elf.so.1: scott# /lib/libiconv.so.3: unsupported file layout Whats wrong? /libexec/ld-elf.so.1 exists, same as the second one, is there any solution for that?

  Read the article

• Running telnet standalone - possible?

  - by Lanz

  So, this is what I want to do: there is a local non-superuser and it can upload the file into /tmp. Using this account, I download a telnet server package equivalent to what is already installed. I modify some settings, setting all file directories into /tmp. Then compile and run as a standalone telnet server. Is this possible? If not, what makes this impossible? Or as a non-privileged user, would there be any way to enable telnet?

  Read the article

• How can I make an alias expand to a list of recipients returned by a command?

  - by Frerich Raabe

  I have an rarely used /etc/aliases entry vmailusers: :include:/usr/local/etc/vmailusers The /usr/local/etc/vmailusers file is generated by a cronjob executing ls /home/vmail | grep -v lists > /usr/locale/etc/vmailusers chmod 0640 /usr/local/etc/vmailusers chmod mailnull:mail /usr/local/etc/vmailusers Is there a way to avoid having to run a cron job but rather execute the ls command in the very moment the vmailusers alias is used?

  Read the article

• unable to start apache after changes to rc.conf and resov.conf

  - by shupru

  I had a working configuration this morning with the following simple /etc/rc.conf ifconfig_rl0="DHCP" ifconfig_xl="inet 192.168.1.11 netmask 255.255.255." defaultrouter="192.168.1.1" I added the following lines: firewall_enable="YES" firewall_type="SIMPLE" firewall_logging="YES" sshd_enable="YES" apache_enable="YES" mysql_enable="YES" my httpd.conf includes: NameVirtualHost 192.168.1.11 <VirtualHost 192.168.1.11> ... </VirtualHost> now apache and ssh server are down. changed rc.conf back to last working configuration and still no ssh or apache apachectl start #--> /usr/local/sbin/apachectl start: httpd could not be started apachectl status #--> Looking up localhost Making http connection to localhost Alert!: Unable to connect to remote host.

  Read the article

• Does ZFS replace the need for hardware/software RAID?

  - by user53744

  I want to provide protection against data loss on my servers. Typically, I'd use hardware RAID 1 or 5, but I've been reading up on ZFS. Is it correct that ZFS itself provides RAID 1 or 5 like data protection WITHOUT needing a RAID controller card? If so, I assume a single hard drive is not enough to provide data protection since if that drive fails, all data fails, so how many hard drives do I need to be running for ZFS to provide this protection?

  Read the article

• what are the vulnerabilities installing openvpn client on a customer's unattended server?

  - by senorsmile

  We run Pfsense as our primary firewall. We also have OpenVPN server running on that box to allow us to remotely connect to our network. My question is: if we have a customer's mostly unattended server that we want to access remotely, what security vulnerabilities are there to installing openvpn on the customer's server as a client connecting to our network. Presumably, we would want to limit/restrict that server's access to the rest of our network. How do we lock openvpn down and are there ways to detect abnormal activity coming from an openvpn client?

  Read the article

• Moving Life files on a unix like system

  - by Recursion

  On a recent job classified, it was listed as a requirement to have the ability to move live files in a data center setting. What does this mean and how can one move live files? The Posting for for a general Unix admin at a datacenter.

  Read the article

• Allow connection to certain port from specified domain

  - by Scott

  I got two domains, which are pointing on the same IP address, I can use both to connect to the server or certain port (TeamSpeak), the problem is that I would like the only one domain from those two to be working while connecting to a certain port. Eg. example.com points at the 11.22.33.44 -- allow connection to the certain port from this domain. sample.com points at the 11.22.33.44 -- disallow connection to the port specified above from this domain. I know this would be possible for the IP addresses, but would it be possible for the domains?

  Read the article

• Moving live files on a unix like system

  - by Recursion

  On a recent job classified, it was listed as a requirement to have the ability to move live files in a data center setting. What does this mean and how can one move live files? The Posting for for a general Unix admin at a datacenter.

  Read the article

• How to get the CentOS 5.6 alsa drivers which will really work with one shot, without any internet.

  - by 89899.3K

  I have one chance to install this in my server on site. Server that i am running is CentOS 5.6 (Dell R310, RAID1) where i need to install alsa-sound driver so that anything related to audio recording from rtsp is working (rail station/rail passing video recording including audio, where audio is not working). Unfortunately i do not have any kind of internet in that odd none human location so yum will not work for me. I need a offline way to install alsa drivers including missing dependencies if arise. What and where i can download this to my usb or cd? so that i can successfully install it (like mission complete). Thanks

  Read the article

• ipfw is blocking access to a script

  - by user225551

  I need to figure out how to troubleshoot why ipfw is blocking my script. This script parses out some rss feeds over the net. I have about 10 different feed urls. About 5 or 6 of these urls are returning xml, the others are timing out. If I turn the firewall off, they will all work. The issue I'm having is that I have no idea what port I need to open for the urls that are timing out. Is there a command that will show me this?

  Read the article

• Looking for VCS wrapper that tracks system files changing across the whole *nix OS and sends diffs through email

  - by nextus

  I need some software that looks after custom directories across the whole OS (i.e. /etc) and alerting me if someone edit something file inside. Additionally, this tool must automatically commit and push changes into backup server, so I can easily determine when specific change in specific file was made. I'm using cvsbackup right now but I want to create or found something more modern. I think using git as VCS is a great idea. I could have local repository and easily revert changes in my configuration files. Furthermore, pushing changes to the remote repository would helps me to recover my configuration files when the server is fault. It doesn't seems difficult to write some wrapper around the git but there are a lot of problems. For example, I need to track custom directories: /usr/local/nginx/ and /etc/. So the destination point for my git repository is /. I don't need to track the other directories so I must to write overwhelming .gitignore rule: * !.gitignore !/etc/ !etc/* !/usr /usr/* !/usr/local /usr/local/* !/usr/local/nginx !/usr/local/nginx/* It's very daunting and prone to error. So it's maybe a good idea to create intermediate file that wrapper reads and converts to .gitignore format. Additionally, I don't want to keep my .git folder in / partition so I need to set appropriate GIT_DIR and GIT_WORK_TREE variables for git. Is there any ready to use tools for implementation this task? I don't found any but I don't believe that no one needs this feature.

  Read the article

< Previous Page | 37 38 39 40 41 42 43 44 45 46 47 48  | Next Page >