Search Results

Search found 20970 results on 839 pages for 'real mode'.

Page 412/839 | < Previous Page | 408 409 410 411 412 413 414 415 416 417 418 419  | Next Page >

• How to install the TRIM RAID update for the Intel storage controller?

  - by Mike Pateras

  I just found this article, that says that Intel now supports TRIM for SSDs when the Intel storage controller is in RAID mode. It links to this download page. I'm pretty excited about that, but I'm a little confused. There seem to be two sets of drivers, an executable and something that's bootable. I ran the executable. Is that just to apply the drivers to my system now, and are the bootable drivers so that if I re-format, I won't have to re-run everything? Do I need to do both? And is there a way to check if it worked? I'm running an i7 in Windows 7 (ASUS P6T Deluxe Motherboard) with RAID 0, if that's significant.

  Read the article

• HAProxy NGInx SSL setup

  - by Niclas

  I've been looking around different setups for a server cluster supporting SSL and I would like to benchmark my idea with you. Requirements: All servers in the cluster should be under the same full domain name. (http and https) Routing to subsystems is done on URI matching in HA proxy. All URIs have support for SSL support. Wish: Centralizing routing rules ---<----http-----<-- | | Inet -->HA--+---https--->NGInx_SSL_1..N | | +---http---> Apache_1..M | +---http---> NodeJS Idea: Configure HA to route all SSL traffic (mode=tcp,algorithm=Source) to an NGInx cluster turning https traffic into http. Re-pass the http traffic from NGInx to the HA for normal load-balancing which performs load balancing based on HA config. My question is simply: Is this the best way to to configure based on requirements above?

  Read the article

• 802.11 Capture Frame

  - by ALi

  I am using wireshark in monitor mode to capture all the frame. I buffered all the QosData in order to calculate the biterate of each station on the network. I calculate the biterate but it is not an accurate value. what i need to know is when the station use the network alone and when it uses it with another station? i know if two station with different wifi card for exemple ( st1 802.11g 54 Mb/s, st2 802.11n 300 Mb/s) if st1 uses alone the line the biterate used is 28 MB/s and if st2 uses alone the network the bit rate increase to approximately 150Mb/s but if the two station use the network at the same time the st1 lost about 80% of its bit rate because of the st1 wifi card thx in advance

  Read the article

• ScreenShare: command line and observe only.

  - by Shyam

  Hi, I have a wide TV screen that is attached to a Mac Mini. I am able to use this screen as a second screen using an application like ScreenRecycler. However, Sometimes I want to demonstrate what I am doing on my box on this TV screen. As this TV is attached to a Mac Mini, I want to have a screen sharing done reversed. As I know screen share can be done in observe mode and full screen, this would be more than sufficient. Because it would be pretty useless to run it continuously, I want it on demand. For this, I want to use SSH. So the only thing I would like to know is, how do I start screen sharing in from a Terminal Session. On Windows, I could start an application by using "start notepad.exe", I am looking for something similar. Eventually, I want to make this work on other boxes too. Thanks for your help!

  Read the article

• Kanji characters appear as boxes

  - by s3d10s

  i'm having trouble with the display of japanese characters on Windows 8 Pro (English, 64-bit, updated regularly). They appear as boxes (picture) in windows explorer, windows menus (even in the language settings of control panel), iTunes and nearly everywhere else, besides web browsers. I was using windows 7 until now, and it didn't have any of these problems, and i'm using the same applications now, as i was using in windows 7. Sometimes (!) when i restart the machine the problem goes away, but that isn't a real solution. What i've tried so far: added japanese language to windows of course installed/uninstalled/reinstalled japanase language pack (didn't have any impact though) i've read in one of these superuser topics a possible solution, when i had to create a txt file on the desktop with a kanji in the filename - that also didn't work (but i honestly hope that hacking and tweaking an operation system released in 2012 can't be the solution to display kanjis..) Please give me any ideas, i'm a bit hopeless here, and don't want to spend my life installing operation systems..

  Read the article

• Figure out what non-symlink path would be?

  - by David Mackintosh

  On Linux, if I've cd'd around and am now in a directory, is there a way to figure out what the real path to that directory is if I had not used a symbolic link to get there? Consider: $ pwd /home/dave/tmp $ mkdir -p 1/2/3/4/5 $ ln -s 1/2/3/4/5 5 $ cd 5 $ pwd /home/dave/tmp/5 Or: $ pwd /home/dave/tmp $ mkdir -p 1/2/3/4/5 $ ln -s 1/2/3/4 4 $ cd 4/5 $ pwd /home/dave/tmp/4/5 Is there any way to figure out that /home/dave/tmp/5 is really /home/dave/1/2/3/4/5 ?

  Read the article

• Second video card (PCI) under Windows 7

  - by dbkk101

  I'm trying to get an old PCI video card (Diamond Stealth 2500) along with a normal PCI-E video card. In BIOS, there is a setting to switch between PEG/PCI or PCI/PEG on startup (PEG is PCI-E Graphics). When I use PCI/PEG only the old PCI card works, when I use the other one, only the new PEG card works. In PEG/PCI mode, Windows 7 recognizes the card and shows it in Device Manager as Standard VGA adapter, but it shows a warning for the device ("This device cannot start. (Code 10)").

  Read the article

• SQL Server 2000 + ASP.NET: Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'

  - by Rick

  I just migrated a development workstation FROM: Windows XP Pro SP3 with IIS 6 TO: Vista Enterprise 64bit with IIS 7 Since the move, one of my pages that accesses an SQL Server 2000 database is receiving the following error from my ASP.NET 2.0 web page: "Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'." I have: enabled Windows Authentication in IIS and web.config disabled Anonymous Authentication in IIS set up Impersonation to run as the authenticated user verified that the logged in user (in this case, me) has access to the appropriate database on the SQL Server verified that my login and impersonation information is correct in the ASP.NET page by checking User.Identity.Name and System.Security.Principal.WindowsIdentity.GetCurrent().Name (both display my username) My connection string using SqlConnection is "Server={SERVER_NAME};Database={DB_NAME};Integrated Security=SSPI;Trusted_Connection=True;" Why is it trying to login with NT AUTHORITY\ANONYMOUS LOGIN? I have to assume it's some setting or web.config entry specific to IIS7 since it worked fine before the migration. NOTE: The SQL Server is Windows authentication only - no mixed mode or SQL only.

  Read the article

• Fujitsu Siemens V6535 laptop doesn't wake up - crash when going into standby?

  - by marc

  I'm having trouble with my laptop (Fujitsu Siemens model V6535). It runs Windows 7, and after I upgraded from Vista I've noticed something that makes me really angry. When my laptop goes into Standby, the power LED changes to red and starts blinking (standby mode). When I push the power button to wake it up it, the blinking LED changes to green but nothing else happens. Nothing on the display, no HDD sound. When I press the power button for a few seconds and then try turn it on again, it doesn't display anything. I have to unplug the charger, shut it off, and power it on again without the power cable. Then it starts working. A few days ago I upgraded the BIOS to the newest version, but it doesn't help. Does anyone have any idea what can be wrong?

  Read the article

• How to type a small fraction in Word 2007 equation editor?

  - by Timwi

  In Word 2007’s equation editor, I can enter “1/2” and I will get a properly formatted fraction. However, there is another kind of fraction that uses a smaller font size. How do I type that one using the keyboard alone? I notice that if I switch to linear mode, I get a small box displayed: Using the clipboard, I find that this is the same box (U+25A1) that I also get if I type “\box”. Despite, typing “\box(1/2)” still turns into a normal-size fraction and not the small fraction. How do I type the small fraction?

  Read the article

• Win2008 DC in a Windows 2000 domain: can I keep the old DC?

  - by gravyface

  Will be putting a new Windows 2008 SE Server into a single domain network with two domain controllers, both running Windows 2000 Server. The functional level of the domain is mixed mode/2000. Until a second 2008 DC can be purchased, I'd like to leave the current Win2k operational master DC as a backup DC as the other member servers running 2003 have either accounting/SQL or Exchange on them. Eventually all the w2k servers will be decommissioned, but until then, I need another DC for redundancy. Following the standard process for adding a new DC, can I leave the old operational master DC (or the other backup DC) running after I transfer the FSMO roles to the new server? Will this cause any issues?

  Read the article

• How to create dynamic Scatter Plot/Matrix with labels and categories on both axis in Excel 2010?

  - by user1581900

  Let us consider a following data set: Name | Age | Hair Color ----------------------------- John | Young | Brown Sophie | Old | Blond Adam | Mature| Blond Mark | Teen | Dark Jeremy | Old | Grey Alex | Young | Brown etc... Both Age and Hair Color, can take only defined values(Young/teen/mature/old and Blond/brown/Dark/Grey). Name is the only real variable here. I want to create a Scatter Plot / Matrix that will look something like that: I know that I schould use this tool to add labels to the scatter plot. I also found this youtube video that explains how to display categories on Y-axis Moreover I need the chart to be dynamic as explained in another youtube video. How do I combine all these approaches to get a Scatter Plot with categories as values on both axis?

  Read the article

• How to fill in the network line in the ubuntu interfaces config file?

  - by matnagel

  I have to configure an ubuntu hardy server network interface. The service hoster told me that this is the network data for the machine: IP Range: 111.111.200.74 to 111.111.200.78 Netmask: 255.255.255.248 Broadcast: 111.111.200.79 Gateway: 111.111.200.73 Subnet: 111.111.200.72/29 I am only using the first IP address. I will update the /etc/hosts file with 111.111.200.74, but I am still unsure how the /etc/network/interfaces file should be. This is my plan: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 111.111.200.74 netmask 255.255.255.248 network 111.111.200.??? broadcast 111.111.200.79 gateway 111.111.200.73 As you can see I don't know how to build the network line. How would I calculate the data for the network line and what is the result? (I changed the first 2 octets of the subnet, they are not "111.111" in the real setup.)

  Read the article

• Screen multiuser - Permission denied

  - by Zlug

  I'm trying to send input to a screen session from php. So far I have followed the steps explained here Is running GNU Screen suid root the only way to make multiuser mode work? And I have set "multiuser on" and "acladd www-data" in the screenrc file (or well, no. in another file that I use by the -c option but still) My problem now is that whenever i try to acess screen by php exec('screen -S user/session -p 0 -X stuff "test"'."\n", $ret); I get the error: Cannot opendir /var/run/screen/S-user: Permission denied

  Read the article

• The security database on the server does not have a computer account for this workstation trust relationship

  - by alex

  I have a Server 2008 machine called OTTO I recently, by mistake, booted up an old machine, also called OTTO (the hardware was unstable, so the new one was set up to take it's place) I shut down the old machine, turned it off, and recycled it (it won't ever be back on) Now, whenever i try to log in to the real OTTO with the domain account (mydomain\Administrator) i get the following error: The security database on the server does not have a computer account for this workstation What can I do to fix this? It doesn't appear in active directory any more I've added it, but I'm guessing this had no effect, due to a different SID I can log in as the local administrator however

  Read the article

• Create netbook recovery image without DVD burner (virtual burner?)

  - by Dan

  I have a new Acer Aspire One which is asking to create a recovery DVD. It doesn't have a built in burner, and I don't have a USB burner. However I do have a large USB hard drive. Is there some way to get the recovery software to "burn" an image file instead of a real DVD? I know you can download a Linux recovery image, but the netbook comes with XP. I plan to install Linux on it but I'd like an XP recovery image just in case.

  Read the article

• FTP issue - VSFTPd and connecting to from FileZilla

  - by B Tyndall

  I'm trying to connect to a CentOS Linux box that I have hosted on EC2 and I think I have everything configured correctly but when I try to connect I get this series of messages Status: Connection established, waiting for welcome message... Response: 220 (vsFTPd 2.0.5) Command: USER tyndall Response: 331 Please specify the password. Command: PASS ********* Response: 230 Login successful. Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/home/tyndall" Command: TYPE I Response: 200 Switching to Binary mode. Command: PASV Error: Connection timed out Error: Failed to retrieve directory listing Not sure where to start troubleshooting this issue. Any ideas? Do I need to change any permissions? I would think this ID has the ability to see my own home directory. I am able to push/pull files from the command line version of FTP client working on Windows.

  Read the article

• Reduce visual redundancies in Outlook 2013?

  - by GaTechThomas

  Outlook 2013 has taken a direction of "how much space can I fill with noise and redundancies". Is it possible to reduce this noise in order to maximize use of screen real estate? For example, in the preview pane, can I shrink the header so that it doesn't include so much info. I don't need any info for the sender and I don't need the subject, as they are both included in the email list pane. Additionally, the ability to turn off the detail bar at the bottom of the preview windows would be helpful. Having Reply/ReplyAll/Forward are also redundant and can go. Is it possible to turn this noise off?

  Read the article

• Virtual Desktop Provisioning - Vmware View 5.2 Maintenance Questions

  - by Lee J. DeAngelis

  Currently running an environment of about 400 VMware View 5.2 virtual Desktops. The environment runs pretty efficiently but we sometimes run into problems with certain pools from time to time. Just recently we had a pool that was causing high write latency when users logged in. It just happened all of a sudden and had been working fine for weeks. On a hunch we completely broke down the pool and re-provisioned it from a new image. This corrected the problem. In fact every real issue we've had so far was fixed by a recompose or complete break down and re-provisioning of one pool or another.Our environment consists of Cisco UCS and Netapp 3240s using flashcache running VMware View 5.2. My questions are: What are some maintenance best practices other VDI admins are using? How often are you recomposing? rebalancing? re-provisioning? How long should you keep base image snapshots around?

  Read the article

• How can I fix my WRT54GL's constant crashing?

  - by Aarthi

  I have a Linksys WRT54GL wireless router (the old blue-and-black) whose underside indicates it is Version 2. I've noticed that, on wireless mode, if I am on a Skype call or in a Google Hangout, the wireless aspect will crash completely. In addition, if I am connected via an ethernet cord, my quality (that is, how my voice is received) tanks very quickly. I suspect this is due, in part, to my internet connectivity itself (I'm on Comcast instead of Verizon FiOS, as I'd prefer) but I'd like to stop my wireless router's wireless capability from crashing. I considered a firmware upgrade, but it looks to me as if I am upgraded. Short of manually running ethernet all over my house, I'm not sure what to do. How can I solve my wireless router's issues? If the answer is "buy a new router," then that's valid, as well, in my opinion.

  Read the article

• strange behaviour - dhclient needs to be run twice in order to connect to wireless

  - by splicer

  I am trying to connect my to my wlan without the use of NetworkManager. I run the following commands after boot: iwconfig wlan0 enc <WEP passwd> mode managed essid <name> channel 6 ifconfig wlan0 up dhclient wlan0 At this point, dhclient stalls for ages (perhaps 2 minutes), then it returns with PING 192.168.1.254 (192.168.1.254) from 192.168.1.65 wlan0: 56(84) bytes of data. --- 192.168.1.254 ping statistics --- 3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 3000ms pipe 3 .. The strange thing is that when I run pkill dhclient; dhclient wlan0 right after this, it connects in about <3 seconds. Any idea what could be the cause of this problem? Edit: oh, and I did try using the -timeout flag on dhclient but that didn't seem to make any difference (it still stalled for ages).

  Read the article

• Troubleshooting intermittantly long 'page loading' problem

  - by justSteve

  Working off IIS 7 with an asp.net mvc app. Most page accesses are lightening quick. Sometimes the browser reports 'page loading' for an exceptionally long time. We are still in the development/testing mode so it's not a network/bandwidth issue. Happens in both IE and FF. No explicit error conditions in the server logs. If i could reproduce it i could run firebug/fiddler to give more info. As it is, it's a little too infrequent to simply leave both those running hoping for the condition to fire - unless/until that's the only option to get better info. I have a hunch this is client-side jquery/ajax related but only a hunch - don't have enough background in either jQuery or MVC to really know what can go wrong. Any initial troubleshooting suggestions welcome. thx

  Read the article

• dhcrelay running as both DHCP and DHCPv6 relay agent on CentOS 6.2

  - by Tibor

  I am trying to set up a DHCP relay agent that would relay DHCP requests for both IPv4 and IPv6. I am using CentOS 6.2 and I am using the dhcrelay from the ISC DHCP implementation. I would like to set it up as a service, but the man page for dhcrelay states: -6 Run dhcrelay as a DHCPv6 relay agent. Incompatible with the -4 option. -4 Run dhcrelay as a DHCPv4/BOOTP relay agent. This is the default mode of operation, so the argu- ment is not necessary, but may be specified for clarity. Incompatible with -6. It seems that the -6 and -4 options are incompatible. How would I still make it work for both protocols without rolling my own service wrapper for both cases?

  Read the article

• DD-WRT/openwrt question

  - by Shiki

  Can I squeeze more speed out of my router (when it comes to USB attached storage device on it) with open/DD wrt? (Sorry I don't really know such firmwares.) (Guess it works with ntfs-3g? I don't know.) Feel free to make this a real question. Basically the question: Does the change worth it in the terms of speed? (My router is a TP-Link WR1043N. Edited it out of the question since it would make it too specified.)

  Read the article

• Mass remove passwords from rar archives

  - by ldigas

  Is there a way to (I'm using WinRAR; demo, but I'm willing to change it to whatever is needed) mass remove passwords from a bunch of files ? Problem description: for reasons unknown to me, some archiving was done for two-and-something years in RAR format, and all archives have passwords. I have a list of them, them all being similar (mostly something like John-03, John-04, John-05 ... e.g. name-month ...) but I need to manipulate the files at large, and it is a real problem removing and or dearchiving all those files, while entering passwords manually. What would be my best options concerning ? Ideally, I'm looking for some kind of archiver which tries out a predefined list of passwords, and asks only if non of them cracks the safe. Afaik, WinRAR has no such feature.

  Read the article

< Previous Page | 408 409 410 411 412 413 414 415 416 417 418 419  | Next Page >