Search Results

Search found 21319 results on 853 pages for 'state management'.

Page 413/853 | < Previous Page | 409 410 411 412 413 414 415 416 417 418 419 420  | Next Page >

• Cliq Wireless questions

  - by Nathan Adams

  Heres the deal: I am by no means a Linux expert, even less when it comes to the Android OS but lets see if we can't solve this problem. The problem I am having is that on the Cliq we have a broadcom chip. In order to use the wireless card you must first insert the module into the kernel. Fine: # insmod /system/lib/dhd.ko insmod /system/lib/dhd.ko # lsmod lsmod dhd 164936 0 - Live 0xbf000000 # BUT netcfg (or ifconfig in busybox) does not recognize that there is a wireless adapter there: # netcfg netcfg lo UP 127.0.0.1 255.0.0.0 0x00000049 dummy0 DOWN 0.0.0.0 0.0.0.0 0x00000082 rmnet0 UP 14.67.164.2 255.255.255.252 0x00001043 rmnet1 DOWN 0.0.0.0 0.0.0.0 0x00001002 rmnet2 DOWN 0.0.0.0 0.0.0.0 0x00001002 usb0 DOWN 0.0.0.0 0.0.0.0 0x00001002 # busybox ifconfig busybox ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:282 errors:0 dropped:0 overruns:0 frame:0 TX packets:282 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:18754 (18.3 KiB) TX bytes:18754 (18.3 KiB) rmnet0 Link encap:Ethernet HWaddr EE:83:E8:B4:4A:ED inet addr:14.x.x.x Bcast:14.67.164.3 Mask:255.255.255.252 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7148 errors:0 dropped:0 overruns:0 frame:0 TX packets:7659 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2609236 (2.4 MiB) TX bytes:908575 (887.2 KiB) # For giggles if we attempt to launch wpa_supplicant anyways we get this: # wpa_supplicant -Dwext -ieth0 -c/data/misc/wifi/wpa_supplicant.conf wpa_supplicant -Dwext -ieth0 -c/data/misc/wifi/wpa_supplicant.conf ioctl[SIOCSIWPMKSA]: No such device ioctl[SIOCSIWMODE]: No such device Could not configure driver to use managed mode ioctl[SIOCGIFFLAGS]: No such device Could not set interface 'eth0' UP ioctl[SIOCGIWRANGE]: No such device ioctl[SIOCGIFINDEX]: No such device CTRL-EVENT-STATE-CHANGE id=-1 state=0 ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWENCODEEXT]: No such device ioctl[SIOCSIWENCODE]: No such device ioctl[SIOCSIWAUTH]: No such device WEXT auth param 7 value 0x0 - Failed to disable WPA in the driver. ioctl[SIOCSIWAUTH]: No such device WEXT auth param 5 value 0x0 - ioctl[SIOCSIWAUTH]: No such device WEXT auth param 4 value 0x0 - ioctl[SIOCSIWAP]: No such device ioctl[SIOCGIFFLAGS]: No such device # In dmesg we get: <4>[18300.494065] dhd_oob_enable_intr : enable <4>[18305.019976] dhd_net_start failed bus is not ready <4>[18305.020278] dhdsdio_probe: dhd_net_start failed! Do I need to specify the firmware with insmod? Why are we trying to control the interface manually instead of through the Android API? The Android API doesn't support ad-hoc connections as far as I can tell. The card, I am sure, most certainly can.

  Read the article

• High quality (commercial) Text to English speech software? [closed]

  - by bodacydo

  I'm working on a software project and I am researching text-to-speech products to use. Does anyone know what are the current state of the art text-to-speech systems? Ideally the speech should be indistinguishable from a native American or English speaker. I'm looking for products with SDK or API that I can easily hook into. Just to clarify and iterate on my question - I'm not looking for things like Microsoft's free text-to-speech synthesis program, I'm looking for a high quality professional product.

  Read the article

• Possible to get cleartext password?

  - by Farhan

  I have hosting service hosted on more than 20+ Plesk servers, version 11. As in the previous versions, the passwords were not encrypted, then if i had to design some tools to manage the hosting accounts, i just picked up the cleartext passwords from the Database. but as now the passwords are encrypted, is there any way i can decrypt the passwords? through API or any other way so that i can integrate my php based hosting management with plesk 11?

  Read the article

• Weird random application hang problem

  - by haridsv

  I am trying to understand an application hang problem that started up lately on my windows xp system. The system runs fine for days (sometimes) without ever shutting down or putting it to sleep, but the problem first shows up as one of the apps hanging. The application's UI stops responding or one or more background threads hang, so even though the GUI is responding, it is not doing anything (e.g., in VirtualDub's case, the UI responds fine, but the job doesn't progress and I won't even be able to abort it). The weirdness part comes from the fact that if I try to kill such an app, the program that is used to kill it goes into the same mode (i.e, that hangs instead of the original). E.g., if I use Process Explorer to kill it, the original program exits, but procexp now hangs. If I use another instance of procexp to kill the one that is hanging, this repeats, so there is always at least one program hanging in that state. This is not specific to procexp, I tried the native task manager and even the "End Process" dialog from windows explorer that shows up when you try to close a non-responsive GUI (in this case, the explorer itself hangs). The only program that didn't hang after the kill, is the command line taskkill. However, in this case, explorer hangs instead of taskkill. Also, once this problem starts manifesting, it soon ends up freezing the whole system to the extent that even a clean shutdown is not possible, so I have learned to reboot as soon as I notice this problem, however this is very inconvenient, as I often have encoding batch jobs going on which can't continue the job after the restart. The longer I leave the system running after seeing this problem, the more applications get into this state. I have tried to do a repair install but that didn't make any difference. I also uninstalled some of the newer installs, but again no difference. I tried to search online, but got inundating results for generic hang and crash related problems. Though I couldn't notice any pattern, it seems as though the problem is more frequent if I have some video encoding going on at that time. I had the system running for days when I only do browsing and internet audio/video chat before I decide to start encoding something and the problem starts to show up. I am not too sure if it is the encoding program that first hangs, though I almost always noticed that too hanging (like the VirtualDub stopping to make progress). I also had to reboot 3 times on one day when I was heavily experimenting with encoding. I would appreciate any help in narrowing down this problem and save me the trouble of reinstalling. I don't especially want to loose my gotd installs.

  Read the article

• Quantifying the effects of partition mis-alignment

  - by Matt

  I'm experiencing some significant performance issues on an NFS server. I've been reading up a bit on partition alignment, and I think I have my partitions mis-aligned. I can't find anything that tells me how to actually quantify the effects of mis-aligned partitions. Some of the general information I found suggests the performance penalty can be quite high (upwards of 60%) and others say it's negligible. What I want to do is determine if partition alignment is a factor in this server's performance problems or not; and if so, to what degree? So I'll put my info out here, and hopefully the community can confirm if my partitions are indeed mis-aligned, and if so, help me put a number to what the performance cost is. Server is a Dell R510 with dual E5620 CPUs and 8 GB RAM. There are eight 15k 2.5” 600 GB drives (Seagate ST3600057SS) configured in hardware RAID-6 with a single hot spare. RAID controller is a Dell PERC H700 w/512MB cache (Linux sees this as a LSI MegaSAS 9260). OS is CentOS 5.6, home directory partition is ext3, with options “rw,data=journal,usrquota”. I have the HW RAID configured to present two virtual disks to the OS: /dev/sda for the OS (boot, root and swap partitions), and /dev/sdb for a big NFS share: [root@lnxutil1 ~]# parted -s /dev/sda unit s print Model: DELL PERC H700 (scsi) Disk /dev/sda: 134217599s Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 63s 465884s 465822s primary ext2 boot 2 465885s 134207009s 133741125s primary lvm [root@lnxutil1 ~]# parted -s /dev/sdb unit s print Model: DELL PERC H700 (scsi) Disk /dev/sdb: 5720768639s Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 34s 5720768606s 5720768573s lvm Edit 1 Using the cfq IO scheduler (default for CentOS 5.6): # cat /sys/block/sd{a,b}/queue/scheduler noop anticipatory deadline [cfq] noop anticipatory deadline [cfq] Chunk size is the same as strip size, right? If so, then 64kB: # /opt/MegaCli -LDInfo -Lall -aALL -NoLog Adapter #0 Number of Virtual Disks: 2 Virtual Disk: 0 (target id: 0) Name:os RAID Level: Primary-6, Secondary-0, RAID Level Qualifier-3 Size:65535MB State: Optimal Stripe Size: 64kB Number Of Drives:7 Span Depth:1 Default Cache Policy: WriteBack, ReadAdaptive, Direct, No Write Cache if Bad BBU Current Cache Policy: WriteThrough, ReadAdaptive, Direct, No Write Cache if Bad BBU Access Policy: Read/Write Disk Cache Policy: Disk's Default Number of Spans: 1 Span: 0 - Number of PDs: 7 ... physical disk info removed for brevity ... Virtual Disk: 1 (target id: 1) Name:share RAID Level: Primary-6, Secondary-0, RAID Level Qualifier-3 Size:2793344MB State: Optimal Stripe Size: 64kB Number Of Drives:7 Span Depth:1 Default Cache Policy: WriteBack, ReadAdaptive, Direct, No Write Cache if Bad BBU Current Cache Policy: WriteThrough, ReadAdaptive, Direct, No Write Cache if Bad BBU Access Policy: Read/Write Disk Cache Policy: Disk's Default Number of Spans: 1 Span: 0 - Number of PDs: 7 If it's not obvious, virtual disk 0 corresponds to /dev/sda, for the OS; virtual disk 1 is /dev/sdb (the exported home directory tree).

  Read the article

• Batch update users on Active Directory

  - by FrancisV

  We have around 1000 users in the Active Directory (on Windows 2008 R2) and we would like to batch update a field (student/employee ID number) from the school management system into their existing Active Directory accounts. Obviously, each student/employee ID is unique and needs to be matched to their current Active Directory account. How can this be done? Is there a tool available for this purpose?

  Read the article

• Bladecenter-E Power Module fault

  - by Lihnjo

  We have problem on IBM Bladecenter-E Critical Events Power module 2 is off. DC fault. Power module 4 is off. DC fault. Warnings and System Events Insufficient chassis power to support redundancy What is the best solution for this problem? Thanks AMM Service Data Help SPAPP Capture Available 10/13/2010 17:03:47 1090347 bytes Time: 11/19/2012 11:02:31 UUID: 42E1 5D2F D7BF 41A6 A4A2 48D1 3FB7 0540 MAC Address xx:xx:xx:xx:xx:xx MM Information Name: nnnnn Contact: aaa, bbb, ccc, England Location: [email protected] IP address: 111.222.333.444 Date Time Information GMT offset: +1:00 - Central Europe Time (Western Europe, Algeria, Nigeria, Angola) Adjust for DST: Yes NTP: Enabled NTP Hostname/IP: 111.222.333.444 System Health: Critical System Status Summary One or more monitored parameters are abnormal. Critical Events Power module 2 is off. DC fault. Power module 4 is off. DC fault. Warnings and System Events Insufficient chassis power to support redundancy CHASSIS (BladeCenter-E) in CHASSIS slot: 01 TopoPath is "CHASSIS[1]". Description : BladeCenter-E Width : 1 Sub Type : BladeCenter (BC) Power Mode : 220 v KVM Owner : CHASSIS[1]/BLADE[9] MT Owner : CHASSIS[1]/MGMT_MOD[1] Component Type : CHASSIS Inventory: VPD ID: 336 (decimal) POS ID EXT: 0 (decimal) POS ID: 8 (decimal) Machine Type/Model: 86773RG Machine Serial Number: 99ZL816 Part Number: 39R8561 FRU Number: 39R8563 FRU Serial Number: YK109174W1HV Manufacturer ID: IBM Hardware Revision: 3 (decimal) Manufacture Date: 18 (wk), 07 (yr) UUID: 42E1 5D2F D7BF 41A6 A4A2 48D1 3FB7 0540 (hex) Type Code: 97 (decimal) Sub-type Code: 0 (decimal) IANA Num: 336 (decimal) Product ID: 8 (decimal) Manufacturer Sub ID: FOXC Enviroment data: -------------- Type: : POWER_USAGE Unit: : WATTS Reading: : 0xa Sensor Label: : Midplane Sensor ID: : 0x0 MGMT MOD (Advanced Management Module) in MGMT_MOD slot: 01 TopoPath is "CHASSIS[1]/MGMT_MOD[1]". Description : Advanced Management Module Name : kant Width : 1 Component Role : Primary Component Type : MGMT MOD Insert Time : 28050132 Inventory: VPD ID: 288 (decimal) POS ID EXT: 0 (decimal) POS ID: 4 (decimal) Part Number: 39Y9659 FRU Number: 39Y9661 FRU Serial Number: YK11836CE2RC Manufacturer ID: IBM Hardware Revision: 4 (decimal) Manufacture Date: 50 (wk), 06 (yr) UUID: 1D95 9937 8CA5 11DB 9499 0014 5EDF 1C98 (hex) Type Code: 81 (decimal) Sub-type Code: 1 (decimal) IANA Num: 20301 (decimal) Product ID: 65 (decimal) Manufacturer Sub ID: ASUS Firmware data: Type : AMM firmware Build ID : BPET50P File Name : CNETCMUS.PKT Release Date : 03/26/2010 Release Level : 50 Revision - Major: 80 Port info: ======================================================== Topology Path ID : 1 Label : External Phy Orientation : EXTERNAL Port Number : 1 Type : MGT Physical Meidum : Copper Number of Link Intferfaces : 1 ------------------------------------ Link Ifc ID Number : 1 Link Ifc Transport Protocol : ENET Link Ifc Addr Type : MAC Link Ifc Burned-in Addr : xx:xx:xx:xx:xx:xx Link Ifc Admin Addr : 00:00:00:00:00:00 Link Ifc Addr in use : xx:xx:xx:xx:xx:xx ---------------------------------------------------------- Configuration behaviors: Save Only Enviroment data: -------------- Type: : TEMPERATURE Unit: : DEGREES_C Reading: : 38.00 Sensor Label: : MM Ambient Sensor ID: : 0x0 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +4.81 Sensor Label: : +5V Sensor ID: : 0x1b -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +3.26 Sensor Label: : +3.3V Sensor ID: : 0x19 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +11.97 Sensor Label: : +12V Sensor ID: : 0x16 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : -4.88 Sensor Label: : -5V Sensor ID: : 0x1e -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +2.47 Sensor Label: : +2.5V Sensor ID: : 0x18 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +1.76 Sensor Label: : +1.8V Sensor ID: : 0x15 -------------- Type: : POWER_USAGE Unit: : WATTS Reading: : 0x19 Sensor Label: : kant Sensor ID: : 0x0

  Read the article

• Temperature monitoring on Dell Precision M4500 under Linux: sensors-detect doesn't, what next?

  - by Tikitu

  I have a Dell Precision M4500, Intel Core i5 CPU, running Linux (Ubuntu Lucid), and would like to keep an eye on CPU temperature. I've tried lm-sensors: sensors-detect didn't find any sensors; following its hint ("This is relatively common on laptops, where thermal management is handled by ACPI rather than the OS.") I tried acpi -V but got nothing thermal. The Gnome panel applet "Hardware Sensors Monitor" reports on GPU temperature but nothing else. What should I be trying next?

  Read the article

• Quickly switch Win7 volume normalization on/off?

  - by romkyns

  Is there some way to quickly toggle the state of volume normalization in Windows 7? When it's off watching movies late is tricky, and when it's on it messes with music in a bad way. It's a great feature, but argh, it requires me to make my way through so many dialogs... Any solution that requires no more than a couple of clicks or keystrokes is welcome - shortcuts, AutoHotkey, tray icon apps.

  Read the article

• Lync server 2010 Active Directory Preparation with a Windows Server 2003 DC

  - by juFo

  I'm trying to install Lync server 2010 but i'm stuck for a while now with the "Active Directory Preparation" part of the Lync server 2010 installation. The "Prepare Schema" fails with the following error: "Step 1: Prepare Schema Run once per deployment. Extends the schema for Lync Server. Not Available: Failure occurred while attempting to check the schema state. Please ensure Active Directory is reachable." screenshot: https://skydrive.live.com/#cid=CB15F1A932B364BE&id=CB15F1A932B364BE%211742 The situation: 1 server with Windows Server 2003 (x86), which is the only Domain Controller (DC) 1 server with Windows Server 2008 R2 (x64) where Lync should be installed. First I have found that the DFL/FFL were not correct: On the DC (server2003) I have changed the Domain Functional Level to Windows Server 2003 and also the Forest Functional Level to Windows Server 2003. If I check these settings on the Server2008 with Active Directory Domains and Trusts, I see indeed that the DFL and FFL are being set to Windows Server 2003. (Windows Server 2003 is the minimum required for Lync server 2010) I tried the Lync AD Preparation again but still got the same message: https://skydrive.live.com/#cid=CB15F1A932B364BE&id=CB15F1A932B364BE%211742 I'm logged in on the Server2008 and Server2003 with the domain administrator account. If I check "Active Directory Users and Computers" and go to the directory Users and watch the properties from the Administrator User then it is also a Member of: Domain Admins Domain Users Enterprise Admins Schema Admins Group Policy Creator Owners The firewall on the server2008 is turned off, still nog working So now my question is: what should I do to make the Lync setup (Active Directory Preparation) work? (I would appreciate clear step-by-step suggestions to check.) Thanks in advance. Update 1: Now I've extended AD successfully on the 2003 DC, using this link: http://blogs.pointbridge.com/Blogs/sloan_jason/Pages/Post.aspx?_ID=2 but when I check the Active Directory Preparation again on the Lync install, it still gives me the same error as in the screenshot I've provided. Update 2: I found out that there is a log on "C:\Users\\AppData\Local\Temp\ with this: Get-CSDomainState Get Domain State Error: An error occurred: "Microsoft.Rtc.Management.ADConnect.NoSuitableServerFoundException" "No suitable domain controller was found in domain "OurDomain.LOCAL". Errors:\r\n"OurDCserver.OurDomain.LOCAL5.2 (3790)5.2 (3790) Service Pack1OurDCserver.OurDomain.LOCAL5.2 (3790)5.2 (3790)Service Pack 1"" I thought Lync could be installed with a Windows Server 2003 (according to the documentation on technet) and it doesn't require a SP. :s

  Read the article

• Setting up a very mixed Active Directory network to work with PowerShell Remote Administration

  - by erictheavg

  Summary: I want to be able to monitor the computers on my network, but don't need it to be automated. We're too small to purchase anything like MOM, but too big to do anything manually (~100 machines in two locations). I just keep running into issues, and was wondering if there's a master list of Group Policy settings I can distribute to my environment to get Remote Powershell working. Environment: Our AD network is pretty mixed. The end users have XP SP3, Win 7, and Win 7 x64. The servers include Win2k3 SP2, Win2k8, Win2k8 x64, Win2k8 R2, and Win2k8 R2 x64. Details: I'm trying to get it to work with Remote Powershell, but I run into errors like the following: Connecting to remote server failed with the following error message : The WinRM client cannot process the request. Default authentication may be used with an IP address under the following conditions: the transport is HTTPS or the destination is in the TrustedHosts list, and explicit credentials are provided. Use winrm.cmd to configure TrustedHosts. Note that computers in the TrustedHosts list might not be authenticated. For more information on how to set TrustedHosts run the following command: winrm help config. For more information, see the about_Remote_Troubleshooting Help topic. + CategoryInfo : OpenError: (:) [], PSRemotingTransportException + FullyQualifiedErrorId : PSSessionStateBroken Then I go to the computer (Win2k3 SP2 server) and run winrm quickconfig per the recommendations via google, and it says: Make these changes [y/n]? y WinRM has been updated to receive requests. WinRM service started. WSManFault Message = The client cannot connect to the destination specified in the request. Verify that the service on the destination is running and is accepting requests. Consult the logs and documentation for the WS-Management service running on the destination, most commonly IIS or WinRM. If the destination is the WinRM service, run the following command on the destination to analyze and configure the WinRM service: "winrm quickconfig". Error number: -2144108526 0x80338012 The client cannot connect to the destination specified in the request. Verify that the service on the destination is running and is accepting requests. Consult the logs and documentation for the WS-Management service running on the destination, most commonly IIS or WinRM. If the destination is the WinRM service, run the following command on the destination to analyze and configure the WinRM service: "winrm quickconfig". That's right. It tells me to remedy my winrm quickconfig failure by running winrm quickconfig. I don't want to band-aid this project one google search at a time. I'm sure there is a step-by-step tutorial out there on how to set up a network for powershell remote administration. Does anyone know of one? Books are acceptable. Thanks in advance! I didn't think my question would get this long.

  Read the article

• dns-323: changing UPNP update interval

  - by jldupont

  Is there a way to change the update interval for the UPNP server on a DNS-323? Note: I know about the "refresh" button on the web management console but I'd like to automate/speed-up this process.

  Read the article

• Which ISO burning software do you recommend?

  - by Mark Pim

  I'm looking for people's opinion on the best, free and most reliable ISO burning software out there. Any OS, but state which one(s) in your answer.

  Read the article

• Apache LDAP authentication (mod_auth_ldap) on MacOS Server (10.5)

  - by Ursid

  A - Is there a LDAP authentication module (mod_auth_ldap) for the version of Apache that comes built into MacOS Server 10.5? (I'm pretty sure no, but maybe someone compiled one.) B - If not, can it be compiled into MacOS' version of Apache? (Man, that would be nice.) 3 - If I can't use the Apple version of Apache for this, what is the best way to get Apache LDAP authentication working on MacOS Server 10.5? (Preferably one that works with MacOS Servers management software)

  Read the article

• I have a Windows Server 2008 R2 box with IIS 7.5

  - by bao

  In Event viewer i have found this: The World Wide Web Publishing Service service entered the stopped state. - - 7036 0 4 0 0 0x8080000000000000 6913 System w2k8x64 - World Wide Web Publishing Service stopped 570033005300560043002F0031000000 How to determine, was server stopped by clicking "Stop" in IIS manager or it stopped itself because of some other reasons? When the stop event occured I was logged in via RDP but I don't remember and clicks in IIS Manager...:( there are no error messages in event viewer

  Read the article

• Can I set up multiple accounts on DD-WRT? [closed]

  - by Greg Ros

  Possible Duplicate: Can I set up multiple accounts on DD-WRT? I want to set up multiple accounts on DD-WRT (accounts meaning, username-password pairs). Specifically, I want one to be used primarily for remote web management (though there is no reason to restrict the account to such). Is this possible? If so, how do I go about it? I'm running: Router Model TP-Link TL-WR1043ND Firmware Version DD-WRT v24-sp2 (08/07/10) std - build 14896

  Read the article

• Setup/Guidance/Troubleshooting DPM 2010 Bare Metal Backups

  - by Dan Kingdon

  Hi all, Having difficulties setting up Bare Metal recovery in DPM 2010. Does anyone know of a good guide/walkthrough to talk me through a basic setup? I have tried most of the DPM knowledge base without much luck. I can perform System State backups, but as soon as I enable bare metal the jobs start failing. Error codes are not coming up anything on google at all. Thanks in advance

  Read the article

• Is using Windows Update to find Drivers for laptop good enough?

  - by user22105

  I'm trying to install drivers for my laptop after fresh install of Windows 8. From the manufacturer's website, there are many drivers and utilities available. But after running Windows Update(which finds drivers for the hardware on my laptop), I only had to install a few (the ones with Unidentified Device) I'm wondering if this is good enough? or would I skip some important drivers like Chipset Thermo management etc etc that could potentially cause harm to my laptop?

  Read the article

• How to recover the ubuntu system?

  - by Hoang

  I istalled the ubuntu virtual machine on vmware. However, one time the disk was full, the system was installing some updates, it quit without giving any message. Now the system is crashed, I can not even launch firefox to download data. How can I recover this virtual machine to a previous state?

  Read the article

• PCI-express - is there a typo in the Intel 5500 overview

  - by Martin

  The overview for the 5500 and 5520 chipsets state that there is a total bandwidth of up to 48GB/s on each PCI Express x8 interface. http://www.intel.com/products/server/chipsets/5500-5520/5500-5520-overview.htm My understanding (admittedly from wikipedia) is that PCI-e Gen 2 runs at 500MB/s per lane. The 5520 has 36 lanes, and so would be limited to a total of 18GB/s. Am I missing something here, or is Intel's claimed 48GB/s a typo that should say 18GB/s ?

  Read the article

• Is the master database backup crucial for restoring MS SQL server in the event where you have to res

  - by Imagineer

  I have been advise by Commvault partner support to turn off the backup of the master database as the backup failed due to the log file being lock. The following is the advise given: "The message is caused by Commvault’s inability to backup the master database’s transaction log. If this is happening intermittently its possible that something is locking the transaction log, preventing SQL iData agent from accessing the log. Typically the master database is just a template and is not used by any applications (applications that do require the use of an SQL database create their own) so there should be no harm in preventing it from being backed up You can do this by nominating NOT to back it up in the primary copy for the SQL data agent" The following is the error that I get. sqlxx SQL Server/ SQLxx N/A/ System DBs 19856* (CWE) Transaction Log N/A 01/08/2010 19:00:16 (01/08/2010 19:00:18 ) 01/08/2010 19:03:15 (01/08/2010 19:03:14 ) 1.44 MB 0:01:11 0.071 2 0 1 ITD014L2 Failure Reason: • ERROR CODE [30:325]: Error encountered during backup. Error: [ERROR: [Microsoft][ODBC SQL Server Driver][SQL Server]Cannot back up the log of the master database. Use BACKUP DATABASE instead. [Microsoft][ODBC SQL Server Driver][SQL Server]BACKUP LOG is terminating abnormally.] Job Options:Create new index, Start new media, Backup all subclients, Truncation Log, Follow mount points , Backup files protected by system file protection , Stop DHCP service when backing up system state data, Stop WINS service when backing up system state data Associated Events: • 79714 [backupxx/JobManager] [01/08/2010 19:03:15 ]: Backup job [19856] completed. Client [sqlxx], Agent Type [SQL Server], Subclient [System DBs], Backup Level [Transaction Log], Objects [2], Failed [1], Duration [00:02:59], Total Size [1.44 MB], Media or Mount Path Used [ITD014L2]. • 79712 [sqlxx/SQLiDA] [01/08/2010 19:01:53 ]: Error encountered during backup. Error: [ERROR: [Microsoft][ODBC SQL Server Driver][SQL Server]Cannot back up the log of the master database. Use BACKUP DATABASE instead. [Microsoft][ODBC SQL Server Driver][SQL Server]BACKUP LOG is terminating abnormally.] • 79711 [sqlxx/SQLiDA] [01/08/2010 19:01:51 ]: Query Result [[Microsoft][ODBC SQL Server Driver][SQL Server]Cannot back up the log of the master database. Use BACKUP DATABASE instead. [Microsoft][ODBC SQL Server Driver][SQL Server]BACKUP LOG is terminating abnormally.]. • 79707 [backupxx/JobManager] [01/08/2010 19:00:15 ]: New backup request received for Client [sqlxx], iDataAgent [SQL Server], Instance [SQLxx], Subclient [System DBs], Backup Level [Transaction Log]. Files failed to back up: • Backup Database[master] Failed Please advise, thank you.

  Read the article

• Determine Users Accessing a Shared Folder Using PowerShell

  - by MagicAndi

  Hi, I need to determine the users/sessions accessing a shared folder on a Windows XP (SP2) machine using a PowerShell script (v 1.0). This is the information displayed using Computer Management | System Tools | Shared Folders | Sessions. Can anyone give me pointers on how to go about this? I'm guessing it will require a WMI query, but my initial search online didn't reveal what the query details will be. Thanks, MagicAndi

  Read the article

• VMWare tools not installing with an error

  - by JDS

  VMWare tools not installing on Ubuntu 12.04. I'm using Chef to manage the installation, but the Apt commands fail if run manually. I'm using the VMWare tool Debian repo. Example: $ cat /etc/apt/sources.list.d/vmware-tools-source.list deb http://packages.vmware.com/tools/esx/5.0u2/ubuntu precise main When trying to install, most packages seem to go ok, but one, "vmware-tools-foundation", does not. Example: $ apt-get -q -y install vmware-tools-esx-nox=8.6.10-1.precise Reading package lists... Building dependency tree... Reading state information... You might want to run 'apt-get -f install' to correct these: The following packages have unmet dependencies: vmware-tools-esx-kmods-3.2.0-23-generic : Depends: vmware-tools-foundation (>= 8.6.10) but it is not going to be installed vmware-tools-esx-nox : Depends: ...snip list of deps... E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). $ apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following extra packages will be installed: vmware-tools-foundation The following NEW packages will be installed: vmware-tools-foundation 0 upgraded, 1 newly installed, 0 to remove and 118 not upgraded. 7 not fully installed or removed. Need to get 0 B/5,886 B of archives. After this operation, 86.0 kB of additional disk space will be used. Do you want to continue [Y/n]? y (Reading database ... 103499 files and directories currently installed.) Unpacking vmware-tools-foundation (from .../vmware-tools-foundation_8.6.10-1.precise_all.deb) ... VMware Tools cannot install because it appears that another installation of VMware Tools is already present. Please remove the previous installation and then attempt to install this copy of VMware Tools again. dpkg: error processing /var/cache/apt/archives/vmware-tools-foundation_8.6.10-1.precise_all.deb (--unpack): subprocess new pre-installation script returned error exit status 1 Errors were encountered while processing: /var/cache/apt/archives/vmware-tools-foundation_8.6.10-1.precise_all.deb E: Sub-process /usr/bin/dpkg returned an error code (1) The key seems to be this error: "VMware Tools cannot install because it appears that another installation of VMware Tools is already present. Please remove the previous installation and then attempt to install this copy of VMware Tools again." However, I've tryed removing and purging and can't seem to "trick" VMWare tools into thinking the packages are gone. Apt thinks they are gone. Is there some service/file/cache/lock left that VMWare tools sees that makes it think that VMWare tools are still installed? I've googled and googled but there is no answer to this question with my particular circumstances on the interwebs. VMWare's documentation of this error is minimal.

  Read the article

• Problem installing Exchange Server [closed]

  - by Carlos

  I can't connect to the instance of exchange server 2010 through EMC on the local machine running w2k8 r2. I've checked all the default website bindings, the kerberos auth and WSMan are set to native type in powershell and I still get this error message. Connecting to remote server failed with the following error message: The WS-Management service does not support the request. It was running the command 'Discover-ExchangeServer -UseWIA $true -suppresserror $true'

  Read the article

• Opsview Notifications, how to report event duration

  - by dotwaffle

  At present, Opsview reports recoveries in the following format: RECOVERY: Internal Alarm is OK on host Ellie: SNMP OK - 0 Service: Internal Alarm Host: Ellie Alias: Ellie Address: 1.2.3.4 State: OK Comment: () Date/Time: Mon Oct 5 14:57:53 BST 2009 Additional Info: SNMP OK - 0 What I would ideally like to do is add a "duration" field, so that you can tell without scrolling back on a Blackberry how long the event has been at fault for. Is there an easy solution to this?

  Read the article

< Previous Page | 409 410 411 412 413 414 415 416 417 418 419 420  | Next Page >