Search Results

Search found 13947 results on 558 pages for 'television shows'.

Page 413/558 | < Previous Page | 409 410 411 412 413 414 415 416 417 418 419 420  | Next Page >

• Computer freezing while watching Flash videos from net

  - by t3st

  I have a Windows 7 home basic, while watching videos from net (within 5 minutes) computer starts to freeze and shows 100 percent CPU usage. I first thought it's a browser issue but watching videos from different browsers also has the same issue. My system runs the latest Firefox browser and all my plugins (including Flash) is up-to-date. After this when I shutdown/restart the computer it will go to the login window with out any problem. From there when I tried to log in to any account, the system starts to freeze and again I have to start and run Windows in safe mode (which doesn't show any problem). I read it in an article to do these steps CMD->sfc/scannow chkdsk after that only my system works normally, even now I can't watch any videos on the net otherwise it starts freezing( I can watch downloaded videos in computer without a problem) and have to do the whole process once more (which takes a lot of time). while running sfc/scannow its showed results that some of the files are corrupted and it could not be repaired. Can this be the cause for freezing of my computer while running Flash videos? or is it a hardware related problem? What different steps do I have to take to correct those corrupt files? System restore works only some times.

  Read the article

• VMware Workstation Bridged Network Host UnReachable

  - by user2097818

  VMware Workstation 7 on Win7-64 (Home Premium). I have confirmed this on any guest running on this machine (from winxp to debian). I am using a bridged network connection for my guests (Automatic on VMnet0). All of the network configuration is done with DHCP (including on the host). Problem What I can not do: Ping my host machine from inside any VM. (either shows me "Destination Host Unreachable" or will just timeout) What I CAN do right after power up, with no problems at all. I can connect to the internet from inside the VM I can ping my router from inside the VM I can ping other machines on my network from inside the VM Other machines can ping the VM Other machines can ping the host My host machine can ping the VM (this one is important. read further) Details So I have my router assigned as 192.168.2.1/255.255.255.0, and the router provides the DHCP service (and it seems to be doing so successfully). There are no IP conflicts on the network that I am aware of. All Gateways and Subnet masks are appropriate and matching. My entire workshop is on one single subnet, with one single DHCP server and gateway. There is one method in which I can ping successfully, but it requires an active connection initiated from the host (I start pinging from host to VM). During the period of the active connection, I can successfully ping from VM to host, using explicit IP address. As soon as the host connection is closed, the VM ping starts hanging with the same old messages. My Thoughts This really feels like a firewall problem, but I have turned off all firewalls on host and VM, powered down the network, powered back up, and the problem still persists. And if it was firewall, why would only the IP address associated with bridged VM networks be blocked. I feel as though my host operating system (Win7) is somehow configured incorrectly, or, VMware Workstation is configured incorrectly from the host side. Although I have done my best to put everything in default, I feel like I am missing something silly.

  Read the article

• TCP Keepalive and firewall killing idle sessions

  - by Carlos A. Ibarra

  In a customer site, the network team added a firewall between the client and the server. This is causing idle connections to get disconnected after about 40 minutes of idle time. The network people say that the firewall doesn't have any idle connection timeout, but the fact is that the idle connections get broken. In order to get around this, we first configured the server (a Linux machine) with TCP keepalives turned on with tcp_keepalive_time=300, tcp_keepalive_intvl=300, and tcp_keepalive_probes=30000. This works, and the connections stay viable for days or more. However, we would also like the server to detect dead clients and kill the connection, so we changed the settings to time=300,intvl=180,probes=10, thinking that if the client was indeed alive, the server would probe every 300s (5 minutes) and the client would respond with an ACK and that would keep the firewall from seeing this as an idle connection and killing it. If the client was dead, after 10 probes, the server would abort the connection. To our surprise, the idle but alive connections get killed after about 40 minutes as before. Wireshark running on the client side shows no keepalives at all between the server and client, even when keepalives are enabled on the server. What could be happening here? If the keepalive settings on the server are time=300,intvl=180,probes=10, I would expect that if the client is alive but idle, the server would send keepalive probes every 300 seconds and leave the connection alone, and if the client is dead, it would send one after 300 seconds, then 9 more probes every 180 seconds before killing the connection. Am I right? One possibility is that the firewall is somehow intercepting the keepalive probes from the server and failing to pass them on to the client, and the fact that it got a probe makes it think that the connection is active. Is this common behavior for a firewall? We don't know what kind of firewall is involved. The server is a Teradata node and the connection is from a Teradata client utility to the database server, port 1025 on the server side, but we have seen the same problem with an SSH connection so we think it affects all TCP connections.

  Read the article

• Configuration of Server root email - Change Address and Name on outgoing email

  - by JTWOOD

  As a newbie Postfix user, I've gotten so far and now I am stuck with a SMALL problem. I would like to configure my local network servers to send alerts and like using the following: 1) From address: [email protected] 2) From name: Hostname I can get #1 to work fine using smtp_generic_maps The problem is that on my email client, the name is listed as "root" - as in the header shows the following: Date: Sun, 29 Jul 2012 13:21:01 -0400 (EDT) From: [email protected] (root) To: undisclosed-recipients:; I'd like to change it to "From: [email protected] (Zeus)" I imagine that this can be done in the headers_check, but so far I haven't gotten anything to work and before I waste a ton of time trying to get this to work, I'd like to make sure I am on the right track. My aliasing and genericmaps are set up correctly (As far as I can see and know - the results are correct!). I just want to change that last bit in the From field to reflect the hostname. I would also like to add something in the subject of the outgoing messages for easy filtering - something like Subject: [Zeus.domain] - "Original Subject" Any suggestions are much appreciated. Thanks!

  Read the article

• nginx doesn't find the directory but apache does

  - by Jack Spairow

  I use apache as the backend server and nginx on the frontend. Apache listens to port 8080 and nginx to port 80. What I do is have the root point to the public folder foreach virtualhost: <VirtualHost *:8080> ServerAdmin webmaster@localhost ServerName site.com ServerAlias site.com *.site.com DocumentRoot /var/www/site.com/public <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/site.com/public/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> </VirtualHost> And here's the nginx config: server { listen 80; access_log /var/log/nginx.access.log; error_log /var/log/nginx.error.log; root /var/www/site.com/public; index index.php index.html; server_name site.com *.site.com; location / { location / { proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $host; proxy_pass http://127.0.0.1:8080; proxy_cache one; proxy_cache_use_stale error timeout invalid_header updating; proxy_cache_key $scheme$host$request_uri; proxy_cache_valid 200 301 302 20m; proxy_cache_valid 404 1m; proxy_cache_valid any 15m; } } location ~ /\.(ht|git) { deny all; } } The problem is Apache resolves the domain just fine (site.com:8080), but nginx shows instead a 502 Bad Gateway (site.com:80). I tried looking at the error_log and access_log but I can't find any hint for why can't nginx work. EDIT: The problem was I wasn't able to include that isolated config for nginx.

  Read the article

• Long 'pause' after copying large files on windows 2008

  - by Ian

  I have a mystery regarding pauses after file copies on windows server 2088 (and other releases) When copying large files, like vhds, to locally attached USB disks I often see a long pause after the copy has completed 100%. As an example: robocopying vhd files. The bytes read/written count matches the vhd file size and robocopy shows 100% but it pauses for several minutes. If I do nothing it will continue, but I will have to wait for quite some time - about the same amount of time as it took to get to 100%. The bytes read/bytes written counters for robocopy do not change. My first thought was that the AV had to scan it, but I'm looking at a machine right now which doesn't have an AV installed and this is occurring, so impossible. No other processes are showing read/write byte counts as going up. The behavior is the same if I use the copy command or xcopy. I've seen this on other systems but have never worked out what the cause is. Anyone got any suggestions as to what might be going on?

  Read the article

• Why am I missing 4GB of RAM on Windows Server 2008 R2 64bit?

  - by Nick G

  I noticed today that a server was very low on memory. It physically has 8GB installed and runs Windows 2008 R2 Standard 64bit. It also hosts 2 virtual machines using HyperV. Server is Dell Poweredge R510. However the host OS reports in task manager that it only has 4GB of RAM, despite actually having 8GB and it being a 64bit OS. Computer properties shows Installed memory: 8.00GB (3.99GB usuable). Why would "usable" be half the real RAM installed under a 64bit OS? Additionally nearly all of the 4GB of visible RAM on the host OS is being used by something without anything showing up in task manager (presumably HyperV as it's allocated 3.6GB to the virtual machines its hosting). However that doesn't explain where the other 4GB has gone which Windows can't even see. Where is my missing 4GB of RAM? Update: Dell OpenManage says this: Total Installed Capacity 8192 MB Total Installed Capacity Available to the OS 4096 MB So looks like Nathan's suggestion of memory mirroring might be correct. I'll have to reboot to check this (I think?) Update 2 OK. So I reboot and I get a message saying "the amount of system memory has changed" (despite not having touched the hardware in a year). Once Windows has booted, all 8GB is visible again. Looks like I probably have a hardware RAM issue (I'll perhaps try reseating it whenever I can chuck everyone off the server next). Thanks for your answers and comments. I was hoping it was going to be the mirrored-RAM option but it seems not - that's not even mentioned in the BIOS.

  Read the article

• nginx: js file loads indifferently every refresh

  - by poymode

  I have this nginx problem wherein a js file in a rails app loads indifferently. Whenever I try to access the JS file in the browser and refresh the page, the scrollbar changes length meaning sometimes it loads half the js page, sometimes the whole and sometimes just a part of it. the js file size is 71K. my nginx server is on different server,separate from my rails app. when I try to access the js file directly through the app server, lets say 10.48.30.150:3000/javascripts/file.js it works fine and doesnt show any half-loaded page. but when I use the nginx server which upstreams the rails app, it shows the indifferent page loads. here is my nginx http conf error_log /usr/local/nginx/logs/error.log; pid /usr/local/nginx/logs/nginx.pid; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; server_names_hash_bucket_size 256; access_log /usr/local/nginx/logs/access.log; sendfile on; #tcp_nopush on; keepalive_timeout 0; tcp_nodelay on; #gzip on; #gzip_min_length 4096; #gzip_buffers 16 8k; #gzip_types application/x-javascript text/css text/plain; large_client_header_buffers 4 8k; client_max_body_size 2G; include /usr/local/nginx/conf.d/*.conf; }

  Read the article

• External Dell Display doesn't work with MacBook Pro (2011) after Thunderbolt Firmware Update (1.0 and 1.2)

  - by tom

  Today two Thunderbolt Firmware Updates (1.0 and 1.2) became available for my MacBook Pro (Early 2011). After installing both, my external monitor, a Dell U2713HM, does no longer work. The system detects the display, but the display shows only black. An Apple Thunderbolt display works fine and a MacBook Air can use the Dell monitor without problems. My MacBook Pro can use the Dell monitor just fine when I boot from a USB stick. Therefore, clearly the Thunderbolt Firmware Update seems to be the problem. Does anyone have the same problem? Any solutions or workarounds? I guess there is no way to remove a Thunderbolt Firmware Update once it's installed, right? Update 24.10.2013: Is there no one else with this problem? In the meantime I tried three different cables – none worked. My colleague with the same generation MacBook Pro also can't use my display after installing the firmware update. All colleagues with MacBook Airs and newer MacBook Pros (all didn't receive the firmware update) can use the display. Update 29.10.2013: Wow, ok today my new MacBook Pro Retina 13' (Late 2013) arrived. Guess what, I cannot use the display with it. Only HDMI works – not with the full resolution.

  Read the article

• Windows Small Business System 2003. SQL timeout in Server Performance Report

  - by tetranz

  I'm the volunteer IT admin at a small school. We have SBS 2003 with about ten desktops. The server performance report is emailed to me daily. It is setup with a wizard in the Monitoring and Performance part of the "Server Management" console. It often fails with a "The page cannot be displayed" error. The event log shows Event Type: Error Event Source: ServerStatusReports Event Category: None Event ID: 1 Date: 1/16/2011 Time: 6:03:14 AM User: N/A Computer: ALPHA Description: Server Status Report: URL: http://localhost/monitoring/perf.aspx?reportMode=1&allHours=1 Error Message: Timeout expired. The timeout period elapsed prior to completion of the operation or the server is not responding. Stack Trace: at System.Data.SqlClient.SqlConnection.OnError(SqlException exception, TdsParserState state) at System.Data.SqlClient.SqlInternalConnection.OnError(SqlException exception, TdsParserState state) at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning() at System.Data.SqlClient.TdsParser.ReadNetlib(Int32 bytesExpected) [plus lots more stack trace] This has been happening for years :) I've never really solved it. It seems to be related to WSUS. When it happens, I run the Update Services "Server Cleanup Wizard". That takes a long time to run. If I haven't run it for a while it can take 10 hours. I also run the WsusDBMaintenance.sql script (from TechNet I think) which reindexes the database etc. Those two things seem to get it working again for a while. Recently the "while" has become a couple of weeks. My searching online has revealed lots of people having this problem but no real solution. Does anyone have any good ideas about this? I have to wonder if something in the WSUS SQL schema is not indexed properly. The time that the server cleanup wizard takes seems ridiculous. Thanks

  Read the article

• AutoHotKey temporarily rebind Winkey

  - by wes

  I've got a wireless keyboard that puts some media keys on top of the Function keys, so that by default F4 is actually lock (Rwin & l) and Fn+F4 is a real F4. So I'd like to basically switch those around. Here's what the key history shows: VK SC Type Up/Dn Elapsed Key ------------------------------------- 73 03E d 17.32 F4 ; Fn+F4 73 03E u 0.16 F4 5C 15C d 2.96 Right Windows ; F4 4C 026 d 0.00 L 5C 15C u 0.13 Right Windows 4C 026 u 0.00 L This doesn't do anything: SC15C & SC026::MsgBox,Pressed F4 But this prints that I hit F4 then goes to the login screen: Rwin & l::MsgBox,Pressed F4 So how can I stop it from switching to the login screen? Ideally I'd like F4 (which registers as Rwin & l) to just send F4, Fn+F4 to send Rwin & l, and also have them work with other keys (e.g., a manual !F4 should still close a window). Is this possible?

  Read the article

• Windows 7 Explorer: how to show total size of all files in current folder?

  - by matt wilkie

  In Windows XP Explorer one can turn on Status Bar which shows, among other things, the total size of all the files in the current folder, or if the cumulative size of the selected files. How do I get the same at-a-glance information in Windows 7? Selecting files doesn't count as it stops after 15 files, and it's rare that I'm concerned about total size with that few files (it's pretty easy to estimate in my head). thanks. UPDATE: Information derived from the context menu (select r-click properties) isn't "at a glance", and not as smooth as selecting files and clicking the details link at the bottom in any case. Thank you for fleshing out more of the available routes though. Yes Q19232 is similar to this one, though it is not a duplicate. That question is about looking for easy free-space on disk stats and this one is easy used-space by contents of this folder stats. The answer for both is the same though. You can't! Hopefully someone will figure how to get this lost feature back with a shell extension or something.

  Read the article

• Ubuntu+Win7--disk error press any key to restart

  - by Siddharth

  Apparently,none of the solutions in any other posts and forums worked for me For some reasons I decided to remove ubuntu from my hard disk drive. My partition table(presently): (/dev/sda1) (fat32) 900 MiB ---(MBR,I suppose) (/dev/sda2) (ntfs) 70 GiB -----(Windows 7) (/dev/sda3) (ntfs) 314.88 GiB --(Personal File storage) (/dev/sda4) (ext4) 80 GiB -----(Ubuntu 13.04) (unallocated) -----1.31 MiB So,after moving(cut-paste) everything(for backup) from the fat32 partition using win7..I booted into Ubuntu and copied the remaining 3 files(hidden in Win7 file explorer) --bootmgr,bootsect.bak,and one more which I do not remember.TERRIBLE MISTAKE After this I again booted into Windows and deleted ext4 partition..formatted it to ntfs..and shut down the pc.Then,I put in a Win7 bootable USB..using command prompt I entered bootrec /fixmbr,and bootrec /fixboot.. Restarting showed me the GRUB..choosing windows 7 showed me "Disk Error. Press any key to restart." I also installed a fresh Win7 installation on the 80 GiB partition expecting a Windows Legacy Bootloader with two win7 options..but did not work. Then..I used a Ubuntu LiveUSB to put it back to the present configuration(above) since all methods to restore the MBR failed.. I copied back the fat32 partitions backup files but couldn't copy those 3 files.Somehow ,they had been recreated and were non-replaceable. I do not want to format the win7 partition for a fresh one. I have used boot-repair..Restore MBR option brings back to "Disk error...." without even going through grub..so I reinstalled grub and I'm able to boot into Ubuntu. grub menu shows the win7 option as "Windows 7 (loader) (on /dev/sda1)". paste.ubuntu.com/5753710 paste.ubuntu.com/5775999

  Read the article

• Live Messenger SimilarityTable2 file

  - by adrianbanks

  I am trying to free up some space on my laptop's hard disk and am using a tool (SpaceMonger) that will show me a treemap of the whole disk. The problem I have comes from Live Messenger's SimilarityTable2 file. I have no idea what it is for, but I know that it is a sparse file, meaning that it shows as taking up 8GB of disk space, but actually only takes up 132KB of space on disk. The problem is that because SpaceMonger thinks this file is 8GB, it swamps the other files and takes up most of the treemap, making it hard to see the other files that really are large. Is this file safe to delete? If not, how do I make its actual size on disk match its reserved size? If that's not possible, how can I make SpaceMonger (or another treemap tool) use the real size of the file and not the reserved size? EDIT: I've just realised that I have some NTFS junctions set up, meaning that the same set of directories appear twice. Is there any way to stop this happening as well?

  Read the article

• Log backups "stalling" on SQL 2008?

  - by MattK

  I have interited a box running SQL Server 2008 and Windows 2003, and have had a few events where largeish (35GB) log backups "stall", both before and after the installation of SQL 2008 SP1. The server log ships to a standby, so regular log backups are taken at 15 minute intervals. However, after an index reorg causes the log to grow to about 35GB (on a DB with about 17GB of data), the next log backup runs to ~95% completion, then seems to stop. The process shows as suspended, with a wait state of BACKUPIO. CPU, read, and write activity on the SPID also does not change, and the process stays in this state for hours, when normally a backup of this size should complete in about 20 minutes. This server has a single RAID-1 volume, thus the source database files and destination backup files are on the same volume. However, I cannot determine if another process is blocking the backup. The backup SPID cannot be killed, and the only way to terminate the log backup and clear the lock on the backup file is to cycle the SQL Server service. There was one event where the backup terminated completely, with an error that another process had locked the backup file, but no details about what that process was. Can anyone suggest a cause or diagnostic process to this situation?

  Read the article

• How do I troubleshoot nginx not recognizing passenger?

  - by Jade

  Issue: nginx does not seem to recognize my rails application Symptoms: When the server starts up, it shows the "Welcome to nginx!" message instead of my Rails application. Nginx seems to be using the local nginx path instead of the Rails root I specified: 2010/04/18 06:29:06 [error] 783#0: *1 "/usr/local/nginx/html/blog/index.html" is not found (2: No such file or directory), client: 1.2.3.4, server: www.farmerjade.com, request: "GET /blog/ HTTP/1.1", host: "www.farmerjade.com" I used [RVM and Passenger Setup on NGINX][1] to install nginx and passenger on a virtual machine. Here is my nginx configuration: user farmerjade; worker_processes 1; ... http { include mime.types; default_type application/octet-stream; passenger_ruby /home/farmerjade/.rvm/bin/passenger_ruby; passenger_root /home/farmerjade/.rvm/gems/ree-1.8.7-head/gems/passenger-2.2.11; ... server { listen 80; server_name www.farmerjade.com; root /home/farmerjade/farmerjade/public; passenger_enabled on; rails_env development; ... I'd appreciate any help anyone has to offer -- I'm quite new to nginx.

  Read the article

• Can't access site internally, but DNS works

  - by BloodyIron

  1) I have apache2 running a vhost for a website. 2) This apache2 instance is already successfuly setup for other websites on it to be accessible internally and externally. 3) I am using an internal bind9 server to resolve the new website's domain internally to the private IP. This bind9 server is not public facing, nor is it the master server on the internet. 4) The DNS internally resolves to the right IP. 5) Firefox reports "server not found". 6) I have copied the config almost identically to other configs that are known to work (adjusting for proper paths of course). In turn I have reloaded and restarted apache2 repeatedly. 7) I have an entry to forward .org .info .net alternative TLDs to .com in the vhost config for this domain, and my browser goes from .org to .com despite note #5. 8) /var/log/apache2/access.log shows when someone externally tries to access the site, but no activity is observed when someone tries to access internally. Changing the log level does not appear to improve the situation. 9) I am out of ideas, nothing appears to be wrong. Please help? To be explicit. Why is this new site unreachable internally? I would like to clarify on something, even though I have already outlined this. YES I know this system is in a private network. NO it is not going through a router. YES I am using an internal DNS server (bind9) to resolve, and YES it does resolve to the proper internal IP. YES other websites on the same server setup in the same way with internal resolution work right now and have done for a while. Everything for this domain is setup the same as the other working domains as far as I can tell. The other working domains are internally AND externally accessible. This domain I am working with is only currently externally accessible. When I go to it internally firefox tells me "Server not found".

  Read the article

• 3 Monitor PCI-e Graphics card on Linux (without tremendous pain)?

  - by N Rahl

  As we are all painfully aware, the only way to get multiple monitors AND compositing (Compiz) on Linux is to use a single graphics card that can drive both (or in my case all three) screens. I bought a Radeon 5750 specifically because it claims to able to drive 3 monitors. I can plug in 3 monitors (2 DVI, 1 HDMI) and the Catalyst Control Center shows all 3, but only 2 can be enabled at a time. The exact message is: The current settings cannot be applied. Possible issues may include: - Display(s) cannot be enabled. - Setting(s) cannot be applied due to insufficient video memory. So I'm going to assume that either the 5750 doesn't support 3 monitors, OR, more likely, ATI couldn't be bothered to add that support to their Linux drivers. So this is a multipart question: First, can anyone suggest a PCI Express Graphics card that can run 3 screens on linux without tremendous pain? I'm looking for something where you install the driver and all three screens "just work". Does such a card exist? Second, if you have a 5750, have you been able to get it to do 3 monitors? I'm running Ubuntu 10.04 at the moment.

  Read the article

• Physical Debian to VMWare: vmware-converter, dd-image or otherwise?

  - by Dabu

  we have two debian Lenny production machines, both running larger commercial websites. Now these machines need to be moved, and in the process, they need to be virtualized to VMWare ESX. If you believe the internet information, there are several ways to accomplish this. The easiest for us would be to use our weekly dd backup where the whole disk, however, I have no experience with this kind of technology and if it is really possible. The second best way would be via an application on the source machine virtualizing it and generating an ESX compatible VM. However, the software is beta and unsupported, and after installation, nothing really works (the /etc/init.d/vmware-converter script doesn't actually do anything, start and stop reply with success messages, yet ps shows that there are no new processes). The worst way with the most work would be to install a new machine and set it up manually, copying files and databases as needed. This part is clear in it's execution, and my question(s) do not touch this. Is my 1st way possible? Has anyone done this yet, or better, has a page with instructions? Or is there a help page that explains how to correctly install, run and use the vmware-converter tool using a Debian installation (it's possible that I dod something wrong during installation already)? Thank you.

  Read the article

• CD Drive not discovered

  - by user1009073

  I have a self built computer. it uses a P6T Deluxe motherboard, which has both SATA and IDE ports. This was built several years ago, and had an IDE CD/DVD drive. This drive started going bad (would not burn CDs correctly), so I decided to replace it. I had difficultly finding an IDE DVD drive, so I bought a SATA DVD drive. I opened the comnputer, took out the old DVD drive. I left the IDE cable in place, connected to the motherboard, but it is not connected to any drives. I hooked up the new DVD drive, both power and with a SATA data cable (SATA port 3 if I recall). (Sony Optiarc 24x , Newegg URL: http://www.newegg.com/Product/Product.aspx?Item=N82E16827118067 ) When I power on my computer, the drive does NOT show up in Explorer. I can hit the DVD eject button, and the drive will open up, so I know it at least is getting power. I thought, maybe something in the BIOS. When I go to BIOS, boot devices, it shows (1) floppy, (2) my hard drive (3) ATAPI CD Drive. The only other possible BIOS option I could find was uder 'Storage Configuration'. Configure Storage as: My setting is RAID, since I am using two drives in a RAID configuration. Other options were IDE and ACHI. Other than trying to find an IDE DVD drive, is there anything else I can try? The drive does not show up at all in Windows Explorer. I did put in a CD thinking that might help, but nothing happened. Thanks, GS

  Read the article

• nginx virtual hosts are not working, all vhosts goes to the default one

  - by Adirael

  Hello, I just did a clean install of nginx + php-fpm on a VPS running Ubuntu 10.10, nginx is serving and PHP is working fine, but I'm not able to add vhosts to it. Well, I can add them, but only one works, the rest go to this first one. This is my first vhost, for host1: server { listen 80; server_name host1; access_log /var/log/nginx/host1.log; error_log /var/log/nginx/host1.error.log; location / { root /var/www/vhosts/host1/; index index.html index.htm index.php; } location ~ \.php$ { include /etc/nginx/fastcgi_params; #fastcgi_pass 127.0.0.1:9000; fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_param SCRIPT_FILENAME /var/www/vhosts/host1/$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_script_name; fastcgi_index index.php; } } And the second one, for host2: server { listen 80; server_name host2; access_log /var/log/nginx/host2.log; error_log /var/log/nginx/host2.error.log; location / { root /var/www/vhosts/host2/; index index.html index.htm index.php; } location ~ \.php$ { include /etc/nginx/fastcgi_params; #fastcgi_pass 127.0.0.1:9000; fastcgi_pass unix:/var/run/php5-fpm.sock; fastcgi_param SCRIPT_FILENAME /var/www/vhosts/host2/$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_script_name; fastcgi_index index.php; } } The problem is, when I go to http://host1 everything is fine, but on http://host2, it just shows host1! I don't have Apache installed and everything comes from repos. Any pointers?

  Read the article

• Ubuntu: Memory Leak

  - by Keener

  I'm having trouble finding from where this memory leak is occurring. I'm running Ubuntu 8.04 LTS on a Dell XPS M1530. I have 3GB of ram and I'm finding after about an hour or so of use top shows me 2GBs+ used. The strange thing is when I add up the memory percentages by PID either from top or ps aux I find that I should only be using about 20-25% of my available ram. What brought this to my attention was I've begun running vmware server again. Now, obviously the ram usage spikes when I load a virtual machine, but the memory VMware is using does not account for the memory usage I'm seeing via top or free. Stopping vmware server releases the memory which was allocated to it, but I'm still unable to find where this RAM is being used. After a complete reboot, of course, the memory is fine, but very quickly it climbs to 60-80% usage with the processes only appearing to account for a third of that. Any ideas where I should look for more information on what this could be?

  Read the article

• Error authenticating git repository with Redmine

  - by woni

  I've setup Redmine 2.1 on my Debian Squeeze server following this Tutorial HowTo configure Redmine for advanced git integration (I tried to use the grack path). Redmine server is running properly, but I have a problem granting users access to git repositories. When I try to clone a repository it says: error: The requested URL returned error: 500 while accessing The apache error.log shows this entry: [Fri Sep 28 15:50:56 2012] [crit] [client xx.xx.xx.xx] configuration error: couldn't check user. Check your authn provider!: /repo.git/info/refs It also asks me for user and password when cloning, but it shouldn't if I understand the tutorial right. I'm using the Redmine authentication module: <VirtualHost *:80> ServerName my.server.at DocumentRoot "/var/www/my.server.at/public" PerlLoadModule Apache::Redmine <Directory "/var/www/my.server.at/public"> Options None AllowOverride None Order allow,deny Allow from all </Directory> SetEnv REMOTE_USER=$REDIRECT_REMOTE_USER" SetEnv GIT_PROJECT_ROOT /var/git/my.server.at/ SetEnv GIT_HTTP_EXPORT_ALL ScriptAlias /git/ /usr/lib/git-core/git-http-backend <Location /> Order allow,deny Allow from all AuthType Basic AuthName Git Require valid-user AuthBasicAuthoritative Off AuthUserFile /dev/null AuthGroupFile /dev/null PerlAccessHandler Apache::Authn::Redmine::access_handler PerlAuthenHandler Apache::Authn::Redmine::authen_handler RedmineDSN "DBI:mysql:database=redmine;host=localhost" RedmineDbUser "user" RedmineDbPass "password" RedmineGitSmartHttp yes </Location> </VirtualHost> Can someone help me please and explain the error and what I can do to solve my problem?

  Read the article

• Changing time intervals for vSphere performance monitoring, and is there a better way?

  - by user991710

  I have a set of experiments running on a cluster node which is running ESXi 5.1, and I want to monitor the resource consumption on the node itself. Specifically, I am currently running experiments on a subset of the VMs on the ESXi host and wish to monitor resource consumption on those specific VMs. Right now, since I'm using only a single ESXi host, I am using vSphere to access it and the performance reports. Ideally, I would like to get these reports for different time intervals. I can already get the charts for a time interval of 1h, but these are rather long-running experiments and something like 2h, 3h,... would be preferable. However, I cannot seem to change the time interval. Here is an example of what my Customize Performance Chart dialog shows: I am also running on a trial key at the moment. How can I change this interval? Do I need a standard license, or do I just need to turn off the VM (unlikely, but I haven't attempted it yet as these are long-running experiments)? Any help (or pointers to documentation which deals with the above -- I've already looked but did not find much) would be greatly appreciated.

  Read the article

• ASUS laptop doesn't charge/use the battery after reinstalling Windows 7

  - by Stan

  I've done a clean install of Windows 7 x64 on an ASUS X501A laptop. The battery is detected and shows in the system tray as "plugged in, charging". However the charge level stays at 76% and if the AC cord is plugged out the laptop turns off. The laptop does not turn on without being plugged in either. Everything worked perfectly prior to reinstall. I've tried: Downloading and installing all the ASUS drivers, including the ATK ACPI driver Checking the BIOS - there do not seem to be any battery-related settings Flashing the BIOS to the latest version Uninstalling Microsoft ACPI-Compliant Control Method Battery in device manager as suggested on the internet Full power discharge/ATX reset as suggested by ASUS support: remove mains power charger, remove battery, press and hold power button for 10 seconds, reconnect battery and mains and turn on I have a feeling all this may have something to do with the EFI BIOS that comes on the laptop. During the reinstall I had to delete all partitions and start anew, because the Windows installer complained about the improper order of GPT partitions. The EFI System Partition was recreated by the installer, and I am guessing that it may be missing the particular ACPI driver needed to make the battery work. I've tried researching this, but could not come up with any useful info. I am hoping someone here may know a bit more about this and maybe help me understand what's going on and how to fix it. Barring that, I'll have to re-image the drive off an identical ASUS laptop with stock install and hope it fixes things.

  Read the article

< Previous Page | 409 410 411 412 413 414 415 416 417 418 419 420  | Next Page >